Shogun Club G-40 - UP Multimedia Service
Contents
1. 22 Pa 2 22 ase on Ps Par EE or EN EEE ES Pa 2 oe EN EN ES EN TE IE e DEN EN Eer feo Fr foe fo ET ET EE a as an oe an ar aw EN EN ET ef f e fae f ee e f e Dip Switch Position DMX Address 11 DMX Channels Channel 1 Mode DMX Control Sound Active 64 127 DMX Control Auto Run 128 191 Manual Select Sound Active 192 255 Manual Select Auto Run Channel 2 Close Laser Channel 3 Pattern Select Channel 4 Dot and Turn Channel 5 Turn Channel 6 Partition Channel 7 Static Patterns Pattern Size No Partition 64 127 Partition On X Coordinate 128 191 Partition On Y Coordinate 192 255 Partition On X amp Y Coordinate Channel 8 Speed 0 255 0 255 23 0 11 Different2. Arped Shogun Club G 40 ORDERCODE 32020 SHOWELECTRONICS FOR PROFESSIONALS Kanal 1 Kanal 4 Drehen Z Achse amp Zeichenfrequenz Kanal 6 Stauchen Strecken X Y Achse Kanal 8 Geschwindigkeit 23 45 253 255 Schnell Kanal 10 Zoom verkleinern 232 gp 3343 Po 4 54 5 65 6 76 7 87 8 98 9 109 10 120 21 153 54 164 65 175 76 186 87 197 98 208 09 219 20 230 31 241 42 252 53 255 iil Kleines Bild ormal __________ 110120 __ S 121 153 Kleines Bild 154 164 p 165175 o y 176 186 Z gt y y 187197 P 198 208 209 219 220 230 Boo 231 241 A 242 252 SHOGUN Club G 40 DMX Kanalzuordnung und Werte Kanal 2 Kanal 5 Kanal 7 Kanal 9 Zeichen Geschwindigkeit 6 68 9 91 2 114 15 137 38 160 61 183 84 206 07 229 30 252 53 255 Schnell Seite 1 von 3 Kanal 3 Muster Bilder Texte Auswahl LE Muster 8 KreiseimKreis 8 Muster Propeller 6 Fl gel 9 Muster Propeller 8 Fl gel 60 Muster Quadrat unterbrochen 4 mal Ecken SHOGUN Club G 40 DMX Kanalzuordnung und Werte Kanal 3 Muster Bilder Texte Auswahl 66 Muster Dreieck unterbrochen 18 68 Muster Dreieck unterbrochen 3 mal Ecken _ Bogen 80 Muster Quadrat Eken gerundet 86 Muster Stern 12 Zacken Explosion 88 Muster Sonne Explosion 90lMuster Stem 5 Zacken verbogen 96 Muster
3. Only operate the device after having familiarized with its functions Avoid flames and do not put close to flammable liquids or gases Always check the regulations when using a class IIIB laser product Always check and position the laser before anybody enters the room when the laser is facing an area with people Always allow free air space of at least 50 cm around the unit for ventilation Always disconnect power from the mains when device is not used before cleaning Only handle the power cord by the plug Never pull out the plug by tugging the power cord e Make sure that the device is not exposed to extreme heat moisture or dust e sure that the available voltage is not higher than stated on the rear panel e Make sure that the power cord is never crimped or damaged Check the device and the power cord from time to time e If device is dropped or struck disconnect mains power supply immediately Have a qualified engineer inspect for safety before operating If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature e If your Showtec device fails to work properly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Showtec dealer for service e For adu
4. Stem Zacken4 98 Muster Stern 8 Zacken im 8 99 Muster Pentagamm2 Crts Bild_ Hubschrauber meio Auto mea Wal Vogel aust Bio Seite 2 von 3 Kanal 3 Muster Bilder Texte Auswahl Maus faden OoOO ZT aBa Keze O OOOO Haus messa UFOS SSCS sofia a oo Zer O oOo Kreis _ _ Zifer Sim Kreis _ Zifer 8 im Kreis _ _ Zifer Tim Kreis _ Zifer 5 m Kreis _ Zifer 4im Kreis _ _ Zifer Sim Kreis _ _ Zifer 2 im Kreis _ _ Zifer tim Kreis SHOGUN Club G 40 DMX Kanalzuordnung und Werte Kanal 3 Muster Bilder Texte Auswahl _195 Muster Mini Stem Mini 201 Bid Dancing Gi 202 Bild Dancing _203 Bla Dancing GM3 204 Biid Dancing Sim 205 Biid Dancing GMS _206 Bid Dancing 207 Bild Dancing 208 Bild Dancing Gi _ 0 __ 210 Bild Dancing Dancing Dancing 273 Biid _ Dancing 214 Bild_ Dancing _21
5. Thank you Showtec Showtec Shogun Club G 40 Product Guide Warning Safety instructions Operating Determinations Description A Features and Overview AC E EEE E E E EE Set Up and Operation 5 One Shogun G 40 Stand alone mode One Shogun G 40 Sound Active One Shogun G 40 Auto ee ee eher Multiple Shoguns G 40 Master Slave Multiple Shoguns G 40 DMX Control DMX DSWIICH SEIN Ges ee een re euere ______ _ _ DMX Quick Reference Chart DMX Channels Maintenance en Replacing the Fuse Troubleshooting No Light No Response to DMX ae nee pe ee ee r D ON 11 12 13 13 14 14 15 WARNING LASER VG ig rx CAUTION EYEDAMAGES IN NEVER LOOK DIRECTLY INTO THE LIGHTSOURCE NEVER PROJECT A SINGLE LASER POINT CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP SAFETY INSTRUCTIONS Every person involved with the installation operation and maintenance of this device has to be qualified follow the instructions of this manual CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires B
6. protect the laser Before plugging the unit in always make sure that the power supply matches the product specification voltage Do not attempt to operate a 120V specification product on 230V power or vice versa The laser will only work between 15 35 C After 3 hours working you must shut off the laser and let the laser diode cool off for 30 minutes otherwise the laser could be damaged and the warranty becomes void Always disconnect from electric mains power supply before cleaning or servicing Damages caused by non observance are not subject to warranty One Shogun G 40 Stand alone There are 4 possibilities Stand Alone Sound active mode Master Auto Mode Master DMX 1 Fasten the Shogun onto firm trussing Leave at least 0 5 meter on all sides for air circulation 2 Plug the cord into a proper electric power supply socket 1112131415 6 7 12 Sound Active Auto Mode _ ON Master Sound Master Auto ON ON EI EI FI Le ON es eee DM 1 Set DMX ADDRESS ON Test _ Sound Active Turn on the music If Dip switches are all set to 0 then the fixture will react to the beat of the music See page 10 for Dipswitch settings After every new dipswitch settin
7. 5 Bid Dancing 216 Bild Dancing 2217 Bild Dancing 67 _218 Bid Dancing _219fBia Dancing 220 Bild Dancing 221 Bild Dancing 61 222 Dancing _22 Dancing Gi 23 224 Biid Dancing 225 Biid Dancing 226 Biid Dancing Gi 2 227 Biid _ Dancing _22 _ Dancing 229 Bild_ Dancing Gi 29 _ Dancing Gi 30 231 Biid Dancing Gns 232 Bild Dancing 233 Biid Dancing 6133 234 Bild Dancing 236 Bild Dancing 236 Bild Dancing 237 Biid Dancing _2 _ Dancing _239 Bid Dancing Gi 39 240 Biid _ Dancing Gi 40 222 Elefant Oooo 245 Biid Olympia Ringe mit Lauer Seite 3 von 3 Congratulations You have bought a great innovative product from Showtec The Showtec Shogun Club G 40 brings excitement to any venue Whether you want simple plug amp play action or a sophisticated DMX show this product provides the effect you need You can rely on Showtec for more excellent lighting products We design and manufacture professional light equipment for the entertainment industry New products are being launched regularly You can get some of the best quality best priced products on the market from Showtec So next time turn to Showtec for more great lighting equipment Always get the best with Showtec
8. ation 2 Use a 3 p XLR cable to connect the Shoguns and other devices The pins 1 Earth 2 Signal 3 Signal 3 Link the units as shown in figure 4 Connect a DMX signal cable from the first unit s DMX out socket to the second unit s in socket Repeat this process to link the second third and fourth units 4 Set DMX dip switches as follows See Dip Switch setting page 10 Shogun G 40 Address Value DMX Dip Switches ON Unit 1 1 1 and for DMX 10 and 12 Unit 2 11 1 2 4 and for DMX 10 and 12 Unit 3 21 1 3 5 and for DMX 10 and 12 Unit 4 31 1 2 3 4 5 and for DMX 10 and 12 5 Supply electric power Plug the end of the mains power cord into proper electric power supply sockets Do so for all units and the controller You can control up to 32 Shogun devices in Master Slave Mode DMX 512 DMX Set up Master Slave Set up Fig 4 Note Link all DMX cables and set dip switches before connecting electric power 6 Do not supply power before the whole system is set up and connected properly Design your show according to your DMX controller functions After every new dipswitch setting you have to disconnect the power and then turn the power on to activate the new dipswitch setting DMX Dip Switch Setting DMX products must have their own address to receive DMX signals Addresses on the Showtec Shogun Club G 40 are set by flipping the appropriate DMX dip switches A standar
9. d DMX address for a Showtec Shogun G 40 which has 10 channels is as follow Shogun G 40 Address Value DMX Dip Switches ON Unit 1 1 1 and for DMX 10 and 12 Unit 2 11 1 2 4 and for DMX 10 and 12 Unit 3 21 1 3 5 and for DMX 10 and 12 Unit 4 31 1 2 3 4 5 and for DMX 10 and 12 Explanation Since each unit has 10 channels each address advances 10 values See Address Value above Once address values are determined set the appropriate DMX dip switches on each unit Example 1 If you want to give a Shogun DMX address133 you first have to find the number 133 in the DMX Chart 2 Then look at the left side Dip Switches 1 5 horizontally from 133 In the Table you ll see 1 ON 2 OFF 3 ON 4 OFF 5 OFF 3 Finally look at the upper side of the table Dip Switches 6 9 vertically from 133 In the Table you ll see 6 OFF 7 OFF 8 ON 9 OFF DMX Address Quick Reference Chart Te a Pa Pee ENEN EN EN Ce 10 DMX Address Quick Reference Chart Dip Switch Position poses mor ef ef ef 1 Te a To iw om EEEN oe Pa ae roe ase
10. efore your initial start up please make sure that there is no damage caused by transportation Should there be any consult your dealer and do not use the device To maintain perfect condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual Please consider that damages caused by manual modifications to the device are not subject to warranty This device contains no user serviceable parts Refer servicing to qualified technicians only IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device e Never unscrew the housing e Never aim the laser beam at people or animals e Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution e Never remove warning or informative labels from the unit e Never use anything to cover the ground contact e Never look directly into the light source 2 Never leave any cables lying around Do not insert objects into air vents Do not connect this device to a dimmerpack Do not switch the device on and off in short intervals as this would reduce the lamps life Do not shake the device Avoid brute force when installing or operating the device Only use device indoor avoid contact with water or other liquids
11. g you have to disconnect the power and then turn the power on to activate the new dipswitch setting You can use the Audio sensitivity knob on the back of the Shogun to adjust the sensitivity reaction to the music Auto Mode If Dip switches are set to 1000000000 then the fixture will play all pre programmed patterns Multiple Shoguns G 40 Master Slave 1 Fasten the effect light onto firm trussing Use a 30 kg rated or stronger C clamp fastened onto the Shogun Leave at least 1 meter on all sides for air circulation 2 Use a 3 p XLR cable to connect the Shoguns and other devices The pins 1 Earth 2 Signal 3 Signal 3 Link the units as shown in figure 4 Connect a DMX signal cable from the first unit s DMX out socket to the second unit s in socket Repeat this process to link the second third and fourth units 4 Set DMX dip switches as follows See Dip Switch setting page 10 Shogun G 40 DMX Dip Switches ON Unit 1 Master Either Sound Active All dipswitches OFF or Auto Mode Dipswitch 12 ON Unit 2 Slave Dipswitch 10 ON Unit 3 Slave Dipswitch 10 ON Unit 4 Slave Dipswitch 10 ON 5 Supply electric power Plug the end of the mains power cord into proper electric power supply sockets Multiple Shoguns G 40 DMX Control 1 Fasten the effect light onto firm trussing Use a 30 kg rated or stronger C clamp bolted onto the Showtec Shogun bracket Leave at least 0 5 meter on all sides for air circul
12. lt use only Lighteffect must be installed out of the reach of children Never leave the unit running unattended e For replacement use fuses of same type and rating only e The user is responsible for correct positioning and operating of the laser The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this laser e This device falls under protection class Therefore it is essential to connect the yellow green conductor to earth The laser will only work between 15 35 C After 3 hours working you must shut off the laser and let the laser diode cool off for 30 minutes otherwise the laser could be damaged and the warranty becomes void e Repairs servicing and electric connection must be carried out by a qualified technician e WARRANTY Till one year after date of purchase CAUTION AVOID EXPOSURE TO BEAM Avoid direct eye contact with laser light Never intentionally expose your eyes or others to direct laser radiation Compliance Statement Your Shogun Laser has been designed to comply with FDA and IEC Standards for it classification The Shogun is a Class IIIB laser product Laser Safety and Compliance Information The Shogun is manufactured to comply with the IEC 60825 1 and in accordance with U S Food and Drug Administrations FDA Standards Listed under FDA Document 21 CFR 1040 and subsequent laser notices Product Classification and Manufacturing Label Identification La
13. n crash etc You endanger your own safety and the safety of others Rigging Please follow the European and national guidelines concerning rigging trussing and all other safety issues Do not attempt the installation yourself Always let the installation be carried out by an authorized dealer Procedure If the laser is lowered from the ceiling or high joists professional trussing systems have to be used Use a clamp to mount the laser with the mounting bracket to the trussing system e The laser must never be fixed swinging freely in the room e The installation must always be secured with a safety attachment e g an appropriate safety net or safety cable e When rigging derigging or servicing the laser always make sure that the area below the installation place is blocked and staying in the area is forbidden Improper installation can cause serious damage to people and property Proper Usage Safety and Compliance Information According to FDA Regulations you should operate this product as stated on the left 2 5meter Connection with the mains Connect the device to the mains with the power plug Always pay attention that the right color cable is connected to the right place Cable Pin internationai BROWN FASE BLUE YELLOW GREEN EARTH Make sure that the device is always connected properly to the earth Description of the device Features The Showtec Shogun Club G 40 is a laser effect
14. ny deformations on housings fixations and installation spots 3 The electric power supply cables must not show any damages or material fatigue Replacing the Fuse Power surges short circuit or inappropriate electrical power supply may cause a fuse to burn out If the fuse burns out the product will not function whatsoever If this happens follow the directions below to do so 1 Unplug the unit from electric power source 2 Insert a screwdriver into the slot in the fuse cover Turn the screwdriver to the left at the same time gently push a bit Turn and Push The fuse will come out 3 Remove the used fuse If brown or unclear it is burned out 4 Insert the replacement fuse into the holder where the old fuse was Reinsert the fuse cover Be sure to use a fuse of the same type and specification See the product specification label for details 13 Troubleshooting No Light This troubleshooting guide is meant to help solve simple problems If a problem occurs carry out the steps below in sequence until a solution is found Once the unit operates properly do not carry out following steps If the light effect does not operate properly refer servicing to a technician Response Suspect three potential problem areas the power supply the laser the fuse 1 Power supply Check that the unit is plugged into an appropriate power supply 2 The laser Return the device to your Showtec dealer 3 The fuse See page 13 for replacing
15. ser Classification Class IIIB Laser medium wavelength 532 nm Green Output 40mW Cooling TE Cooling CAUTION The use of corrective eye wear or optics for viewing at distances such as telescopes or binoculars within a distance of 100mm may pose an eye hazard This laser product is a Class IIIB laser and has an Interlocked housing There are no user serviceable parts inside Tampering or WARRANTY VOID removing warranty seals will void your products limited seal is broken or has been tampered with wa rranty Manufactured for Combo label with the Product Model Number Serial Number Date of Manufacturing Laser Light Warning Label Warranty Void Label and Interlocked Housing Label Model Number Date of Manulacure user serwsoeabie carts inside J ee Ls his product conto wiih FOA 21 0 1040 and subsequent meer Notices OPERATING DETERMINATIONS This device is not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects The minimum distance between light output and the illuminated surface must be more than 0 8 meter The maximum ambient temperature ta must never be exceeded If this device is operated in any other way than the one described in this manual the product may suffer damages and the warranty becomes void Any other operation may lead to dangers like short circuit burns electric shock lamp explosio
16. speeds Channel 9 Draw Speed 0 255 0 255 23 0 11 Different speeds Channel 10 Draw Speed 255 23 0 11 Different speeds 0 original size 1 11 Zoom In 12 23 Zoom Out Always use a new Q tip or cotton swab for each pass Use only Reagent grade acetone or 90 isopropyl alcohol Do not use too much force otherwise the mirror may break Always turn the power off before cleaning Let mirror dry before using the laser again Direction of Dirt on mirrors cleaning Rotate the cotton Q tip Maintenance The Showtec Shogun Club G 40 requires almost no maintenance However you should keep the unit clean Otherwise the fixture s light output will be significantly reduced Disconnect the mains power supply and then wipe the cover with a damp cloth Do not immerse in liquid Carefully wipe both mirrors clean with glass cleaner and a soft cloth Do not use alcohol or solvents The mirrors will require regular cleaning as smoke fluid tends to build up residues reducing the light output quickly Keep connections clean Disconnect electric power and then wipe the DMX and audio connections with a damp cloth Make sure connections are thoroughly dry before linking equipment or supplying electric power The following points have to be considered during the inspection 1 All screws used for installing the device or parts of the device have to be tightly connected and must not be corroded 2 There may not be a
17. the fuse No Response to DMX Response Suspect the DMX cable or connectors a controller malfunction a light effect DMX card malfunction 1 Check the DMX cable Unplug the unit change the DMX cable then reconnect to electrical power Try your DMX control again 2 Determine whether the controller or laser effect is at fault Does the controller operate properly with other DMX products If not take the controller in for repair If so take the DMX cable and the light effect to a qualified technician 14 Product Specification Model Showtec Shogun Club G 40 Voltage 240V 50Hz CE Fuse 2A 250V Dimensions 390x285x135mm LxWxH Weight 5 kg Operation and Programming DMX Channels 10 Signal input 3 pin XLR male Signal output 3 pin XLR female DMX control via standard DMX controller Laser 40 mW green Laser 532nm Minimum distance Minimum distance from flammable surfaces 0 5m Minimum distance to lighted object 0 8m Design and product specifications are subject to change without prior notice 15 2006 Showtec
18. with a high output and great effects 40 mW green laser 532nm DMX control via standard DMX controller 64 Patterns closed loop scanning pair 10 DMX control channels required 12 channels RGY and RGB units e RGY RGY TTL modulation Sound controlled built in microphone e Fuse 2A 250V Overview Frontside 1 Power LED 2 Laser indicator LED 3 Microphone 4 Sound Active LED 5 DMX indicator LED Fig 2 Backside Me gt un Sound Mi T F i sen Loches 1 TA 678 9101112 13 Fig 3 6 Dip Switches 10 Power ON OFF 7 Remote Interlock Connector 11 DMX signal connector OUT 8 Sound Sensitivity control 12 IEC Power Connector Fuse 2A 250V 9 Key System 13 DMX signal connector IN Remote Interlock Connector Use a DB9 connector to connect to the Remote Interlock which stops the beam being emitted once the connection loop has been opened Key System When the key is locked the unit stops emitting the laserbeam but keeps the power on and the steppers keep working Only when the key is turned after 15 seconds the projector starts emitting the laserbeam 5 seconds before emitting there is a rattling sound Set Up and Operation Follow the directions below as they pertain to your preferred operation mode Remove the protection cover from the front of the laser When the laser is not in use please replace the cover to
Download Pdf Manuals
Related Search