USER MANUAL For: XLCD18W
Contents
1. Timer ext FERNE EHER Reset me E S ooo ERE 5 Regulatory Agency 5 1 Safety Approvals This series design shall meet the standards of the following domestic and foreign agencies CE LVD EN60950 2006 All 2009 5 2 EMI EMS Emission Approvals This series design shall meet following EMI EMS specifications FCC Compliance FCC Rules and Regulations Part 15 subpart B Class A CE COMPLIANCE EN55022 2006 class A EN55024 2003 EN50130 4 2003 6 Reliability Mean Time Between Failures MTBF MTBF shall be 30 000 hours minimum at 90 confidence level and 100 duty cycle continuous operation at 25 C The calculation shall not include LCD panel 7 Mechanical 7 1 Cabinet Material Plastic Finish Black 7 2 Dimensions A el 18 Dims mm ee A 8 je D E2. XEne USER MANUAL For XLCD18W F CEG TABLE OF CONTENTS CE information 3 Safety Precautions 2 2 2 2 3 Scope rr e 5 Functional specification nun 9 Controls and indicators 1 x x x2 x x2 7 OSD Menu rr aan zz zzz ze nizza n zz zzz zena zazonanee 8 Regulatory Agency 222 2 2 10 Reliability 44 444 am nn 10 Mechanical esse lee aeg 11 CE INFORMATION The product must be installed according to the currently valid installation regulations for EMC to guarantee the designed use and to prevent EMC problems The device supplied with this manual is according to the EC EMC Directive 2004 108 EC 8 LVD 2006 95 EC SAFETY PRECAUTIONS i oR wh 10 11 12 Do not modify the three prong grounding type monitor power plug in any way Operate this unit only from the type of power source indicated on the label Do not block or cover ventilation openings on the back or bottom of the monitor cabinet Do not place this monitor near a radiator or heating vent Do not push objects of any kind through cabinet openings This may result in fire or electrical shock Before adding attachments always ask a service technician to perform routine safety tests to
3. determine that equipment is in safe operating condition Ground potential tests should be part of the routine safety check made by the service technician Do not place monitor on an unstable cart stand or shelf where it may fall and injure personnel or damage equipment Route power cords so that they cannot be walked upon or tripped over Do not allow anything to rest on the power cord Do not install monitor in wet areas or where it may be exposed to rain or water Do not spill liquid of any kind on the unit Unplug the power cord from the unit before cleaning the display Use only a damp cloth Do not use alcohol spirits or ammonia to clean the display DO NOT ATTEMPT TO CLEAN THE INTERIOR OF THIS UNIT THIS ACTION MUST BE PERFORMED BY THE SERVICE TECHNICIAN AS REQUIRED DURING NORMAL MAINTENANCE Refer all servicing to qualified service personnel REMOVAL OF BACK COVER BY UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO DANGEROUS VOLTAGES OR OTHER HAZARDS Unplug the unit immediately and notify the service technician A If liquid has been spilled into the display or the display has been exposed to rain or water B If the unit has been dropped or the cabinet damaged C If fuses continue to blow D If the power cord is damaged or frayed E If a distinct change from normal operation is apparent When replacement parts are required be sure that the service technician uses components specified by the manufacturer which have the same characteris
4. tics as the original parts UNAUTHORIZED SUBSTITUTIONS MAY RESULT IN FIRE ELECTRICAL SHOCK OR OTHER HAZARDS Upon completion of any service or repairs ask the technician to perform safety checks to determine that the equipment is in safe operating condition WARNING SERIOUS SHOCK HAZARDS EXIST WITHIN THE COVERS OF THIS MONITOR DO NOT OPEN THE COVERS UNDER ANY CIRCUMSTANCES THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE CAUTION USE RECOMMENDED MOUNTING APPARATUS TO AVOID RISK OF INJURY 1 Scope This specification is used to define the performance of the XLCD series color TFT LCD monitor This system can support up to 1920 x 1080 VESA standard The user friendly OSD menu is also provided to make this system easy to operate 2 Functional Specifications 2 1 Power Supply The power supply spec is listed below AC INPUT AC power input range 100 240 V 50 60Hz 1 3Arms max Power efficiency 280 DC INPUT DC JACK power input 12V 10 3 0A max 2 2 PC Input e VGA Input Analog RGB 0 707 Vrms Support VESA Standard Timing e DVI Input DVI 1 0 Compatible Interface Support VESA Standard Timing 2 3 Audio Input Signal Level 1 0 Vrms 2 4 Environmental e Temperature Operating 0 C to 40 C Storage 20 C to 60 C e Humidity Operating 10 to 85 non condensing Storage 10 to 95 non condensing 2 5 EDID This series of displays support EDID but does not support DDC2B function 2 6 Connec
5. tors A DVI INPUT 24 pins DVI D Connector B VGA INPUT D SUB 15 pins Connector C AUDIO INPUT Phone Jack Stereo D DC 12V INPUT DC JACK 5 59 2 59 Set up sequence 1 Make sure the power of PC and or Video source were turned off 2 Plug the power adapter Video signal and VGA cable to monitor 3 Turns the PC and or Video source power on 4 Plug the AC power cord onto power adapter Use reverse sequence to teardown the monitor 3 Controls and indicators A i Auto button O Press the button to run the Auto Adjust Display function B buttons O Press the buttons to scrolling the cursor to desired function e Press the buttons to adjust the value of selected function in sub OSD menu C M Menu button O Press the button to show the OSD main menu O As a confirmation key during the OSD operation D POWER LED Indication O Green Power on O Orange Power off Stand by O Flash Orange Sleep mode O Flash Green Freeze status E POWER button O Press the button to turn ON or turn OFF the monitor 4 OSD Menu 4 1 Menu 4 2 OSD Menu framework 0 100 Brightness O 100 9300 Color 6500 Color Temp Red 07255 ser ed AAA Auto Adjust Function Color Adjust Main Menu VGA and VGA A SRGB Es ONLY o S O S English Deutsch Francais Language Italiano ARE ZEHN fi DVI fe HZ Pyccko OSD OSD H Position 0 100 Menu OSD V Position 0 100 OSD
Download Pdf Manuals
Related Search