Home

User Manual - Nancy`s Knit Knacks

image

Contents

1. 1 year commercial use limited warranty NKK will repair or replace any part of the unit except brakes and wheels that fail during the one year period Buyer must return the unit freight prepaid to NKK and NKK will return the repaired or replaced unit freight prepaid to Buyer Buyer must secure a return authorization from NKK before returning unit Measurement accuracy is not warranted because it is subject to many factors outside the control of NKK and this meter The unit includes a 5 5mm nut driver a 1 16 diameter Allen wrench and a small locknut These are used when changing the wheel or when removing the wheel to clean the fiber from around the wheel shaft You lock the shaft in place with the Allen wrench by poking it through a small hole in the shaft between the wheel and the housing when loosening and tightening the nut on the wheel We do not recommend removing the wheel unless you are specifically addressing a problem or doing maintenance on the shaft removing fiber Care must be used to properly re insert the wheel on the shaft Update 2014 we have developed an improved shaft which eliminates wheel balancing problems Note All production as of 2014 includes the new shaft Thanks for purchasing our EYM Once you start using this unit you will wonder how anyone ever measured yarn length any other way Please refer all questions to us Also visit our User s Forum for more info www nancysknitknacks com Nancy s Knit
2. Allen wrench required to hold the wheel shaft stationary while changing the wheel plus a nylock hex nut Brake use the EYM may be used either with or without the brake installed The EYM may record unintentional additional length at the end of a measurement if the brake is not installed However without the brake installed there will be less drag on the system used to pull the yarn through the EYM ball winder motorized ball winder etc We recommend using the brake 100 of the time because it stops the wheel measurement when the yarn finishes passing through Yarn Path we recommend installing the yarn over the top of the wheel most of the time because it gives you the best accuracy However you can also install yarn horizontally under the wheel when you need to change the way the yarn behaves Position yarn between both posts on both sides or run it over the highest post on both sides If you experience yarn control issues where the yarn misbehaves when going through the meter try reducing your speed and use the horizontal mounting method Meter accuracy under perfect conditions should exceed 99 Page 4 The EYM can be used with the following equipment e NKK Power Base for use with our motorized Ball Winder e Our Motorized Swifts and Skein winders e It can be used with any device as a measurement tool except it cannot be electrically connected to such 3 party devices Warranty The EYM is covered by a domestic USA
3. Knacks LLC 104 Hobblebrook Ct Cary NC 27518 800 731 5648 Fax 866 445 4371 info nancysknitknacks com www nancysknitknacks com Copyright 2009 2014 07 09 14 Page 5
4. A stiffer brake for special hard to Always mount brake with clip height of EYM Module on post brake cases is also available closest to the point of yarn entry d Plug in cable that connects to the Plug in AC adaptor into EYM Power Base Standard Power Base connection Page 1 Operational Overview and Instructions view DVD and website for more information Mode amp Task Depress LEDs LCD Display Preset Button Lit Measure Yards length this is the None Yards default mode Just load your yarn press the RESET once prior to running job Measure Meters length Press the Mode Meters Mode button once to get to Meters Load once your yarn and press the RESET button prior to running job 3 Measure Yards and Ounces weight Mode Yards Press Mode button twice Menu will ask twice Weight you to enter the number of YARDS and OUNCES from the yarn label After each entry press the SAVE button once NOTE in OUNCES Weight Mode the Decade buttons have a unique meaning as follows Use 0000 button to enter tens data Use 000 button to enter units ones data Use 00 button to enter tenths data Use 0 button to enter hundredths data After both numbers have been entered you can load your yarn and press the RESET prior to running job The measurement will then display the number of YARDS and equivalent OUNCES as the yarn is measured 1 Measure Meters and Grams weight Meters Press Mode button three time
5. MW Electronic Yarn Meter User Manual Thank you for purchasing our state of the art Electronic Yarn Meter We believe that this unit is the best system with which to measure yarn that is available today This User Manual will describe the unit s basic functions and features and help you to get the best performance and use from the meter Please review this manual and the video that accompanied it Only then will you fully understand what the meter can do Note throughout this manual we will refer to the Electronic Yarn Meter as the EYM Assembly and Construction the EYM is available in 3 different models Standard for basic use and for use with a plastic ball winder HDBW for use with the NKK Heavy Duty Ball Winder scheduled for early retirement Power Base for use with the NKK Power Base and Heavy Duty Ball Winder All 3 models use the same EYM module electronics and meter housing eS The control panel is shared between the EYM and our ERC used on Swifts The Top Left LED on the EYM relates to weight measurements so ignore the RED colored ROTS rotations Note This manual only shows the original design of the control panel Assemble the EYM stand install brake and cable s Install washers on both sides of mounting rail with knob g Install brake Install the standard Pla N oy Wore o QA O brake white plastic facing down Bee brake Install EYM Module on post Adjust
6. nd the NKK Power Base with turn off if connected Important Information 10 11 12 To clear actual data press RESET once To clear a Preset qty in any mode press the RESET button twice SLEEP Mode the unit goes into SLEEP mode after 5 minutes of inactivity Just press the RESET button ONCE to bring it out of SLEEP mode Your last data will still be displayed unless you press the RESET button a second time When in SLEEP mode the display LEDs and the encoder are turned off Master Reset press the Save and Reset buttons simultaneously to reset all data or you may remove the power plug and re insert it Mode Switch when changing modes all data is lost from the current mode There are 4 Modes Yards Meters Yards and Ounces Meters and Grams All modes can have a Preset mode also Power you may leave the unit on all of the time there is no on off button and it will go into SLEEP mode when not being used For periods longer than a few days disconnect power cord Wheel Changing after the EYM is used extensively over a long period of time you may have to change the wheel as it will show signs of wear on its foam covered surface Please purchase a replacement wheel only from Nancy s Knit Knacks Examine surface for grooves or slickness Wheel Change Tool Kit a wheel change kit is included with the meter and consists of a 5 5mm nut driver required to remove the wheel nut and a 1 16 x 3 long
7. s Menu will Weight ask you to enter the number of METERS and GRAMS from the yarn label After each entry press the SAVE button once After both numbers have been entered you can load your yarn and press the RESET prior to running job The measurement will then display the number of METERS and GRAMS as the yarn is measured __1 Measure Yards up to a Preset Qty None Yards 0 Page 2 Preset length This starts with the default mode Yards Simply enter a Preset number that you want to measure by pressing the decade buttons 0000 000 00 0 and then the SAVE button Press the RESET button once to ensure that your actual count is zero Pull yarn through the meter and when your Preset qty is reached a tone will sound and the NKK Power Base will stop if connected 2 Measure Meters up to a Preset Qty Mode Meters a Preset length Press the MODE button once once to get to Meters Then enter a Preset ke number that you want to measure by pressing the decade buttons 0000 000 00 0 and then the SAVE button Press the RESET button once to ensure that your actual count is zero Start pulling yarn through the meter and when your Preset qty is reached a tone will sound and the NKK Power Base will stop if connected 3 Measure Ounces up to a Preset Qty Mode Yards Preset weight Press Mode button twice twice Weight Menu will ask you to enter the number of YARDS and OUNCES from the yarn label Af
8. ter each entry press the SAVE button once After both length and weight data have been entered you then enter the Preset qty that you wish to measure up to in OUNCES by pressing the decade buttons 0000 000 00 0 NOTE in OUNCES Weight Mode the Decade buttons have a unique meaning as follows Use 0000 button to enter tens data Use 000 button to enter units ones data Use 00 button to enter tenths data Use 0 button to enter hundredths data Then press the SAVE button Load your yarn and press the RESET prior to running job The measurement will then display the number of Ounces actually counted in top row of display and the Preset qty in the bottom row When the Preset number has been reached a tone will sound and the NKK Power Base with turn off if connected Page 3 A Preset Measure Grams up to a Preset Qty weight Press Mode button three times Menu will ask you to enter the number of METERS and GRAMS from the yarn label After each entry press the SAVE button once After both length and weight data have been entered you then enter the Preset qty that you wish to measure up to in GRAMS by pressing the decade buttons 0000 000 00 0 Then press the SAVE button Load your yarn and press the RESET prior to running job The measurement will then display the number of GRAMS actually counted in top row of display and the Preset qty in the bottom row When the Preset number has been reached a tone will sound a

Download Pdf Manuals

image

Related Search

Related Contents

HM8131-2  HP Enterprise Secure Key Manager User's Guide  取扱説明書  HANDBUCH - e-Beam  Panasonic Toughbook CF-C2  Philips 046677422042 energy-saving lamp  Mise_en_page_1_Mise en page 1    Lektüreliste für die Bayerische Staatsexamensklausur  StorageCraft ImageManager User Guide  

Copyright © All rights reserved.
Failed to retrieve file