Untitled - Clinton Electronics
Contents
1. Check if SENS UP is set to AUTO Check if Shutter settings are set to AUTO or 1 30 Clinton Electronics Corp NXHD User Manual a 0 HD SDI INSTALL TIPS Existing Coax Coax cable that once worked fine for analog may not be suitable for HD SDI installations HD SDI is a digital signal that has a different transmission meth od than analog It is important to test the cable before committing to using the existing coax cable for your installation Coax Cable Integrity is Critical Do not kink or bend the coax cable at an extreme angle The integrity of the outer shielding of coax is very important to the HD SDI signal Damaged cable reduces the signal strength and could even cause no video Avoid Splices Splices and poor quality connectors are not suitable for a HD SDI system Avoid splices at all costs and only use high quality compression style BNC connectors Typical Distance The typical distance with Clinton CE CB1000 or CE CW1000 Siamese cable range from 250 275 feet Longer Distances If you plan to run the coax longer than 275 feet we strongly recommend that you use an HD SDI extender like the CE SDIEXT Coax Cable Testing It is advised to use a signal generator CE SDIGEN and a cable tester CE SDITEST to check the cable to see if it will be OK for an acceptable HD SDI signal Analog and HD SDI are not interchangeable While HD SDI and Analog share the same type of cable and connectors that is where the si2. ON SCREEN DISPLAY User Manual Clinton Electronics Corp 6701Clinton Road Loves Park IL 61111 Sales 1 800 447 3306 Support 1 800 549 6393 www clintonelectronics com IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation open ings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sourc es such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electri cian for replacement of the obsolete outlet 10 Protect the power cord from be ing walked on or pinched particular ly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tri pod bracket or table specified by the manufacturer or sold poneis cant WARNING with the apparatus When a cart is used use caution when mo
3. MOTION SELECT Select up to 4 areas to highlight motion DISPLAY Turn ON or OFF the motion detection area as well as adjust the position and size of the area oo MO 5 1 SELECT AREAI 3 SENSITIVITY Ao 4 MOTION VIEW ON 5 DEFAULT a 6 RETURN RET POSITION 1 Position the flashing box to the desired area then press SET 2 Adjust the size of the area then press SET 3 Once you have the desired location and size of the MOTION AREA choose RET Return to apply changes Choose AGAIN to start over to make any needed adjustments to the area gt SENSITIVITY The lower the value the more sensitive the camera will be to motion MOTION VIEW Turn ON or OFF the colored overlay MOTION still displayed on the screen DEFAULT Restores default MOTION settings 11 E Clinton Electronics Corp NXHD User Manual ECIAL gt PRIVACY Apply a mask to an area you want to hide Useful in areas where a camera can see into areas that are not relevant to security needs SELECT Select up to 8 privacy areas the selected area will be flash and be displayed with a thin white outline DISPLAY Choose to have the selected privacy area be shown in COLOR MOSAIC or INV Inverted Position and size of the privacy area are adjustable upon entering the submenu PRIVACY 1 SELECT AREA 3 COLOR 2 4 TRANS 3 SS AUEr POSITION 6 RETURN 1 Position t
4. Adjust the amount of gain to be applied to the BLC area AREA Adjust the position and size of the BLC area 1 Position the white box to the desired area then press SET 2 Adjust the size of the area then press SET 3 Once you have the desired location and size of the BLC AREA set choose RET Return to apply changes Choose AGAIN to start over to make any needed adjustments to the area DEFAULT Restores default BLC settings Qi While using the BLC function it is possible to have the bright portion of the scene appear overexposed 0 Clinton Electronics Corp NXHD User Manual EXPOSUR HSBLC HicHLiGHT Suppression Back LIGHT COMPENSATION If the scene contains extremely bright light areas such as car head lights the light can mask out much of the on screen detail Use the HSBLC feature to remove these bright lit areas to allow detail such as a car license plate number to become visible HSBLC ON HSBLC OFF SELECT Select the desired HSBLC area 1 4 DISPLAY Turn ON or OFF the selected HSBLC area 1 SELECT AREA1 3 LEVEL ma 20 4 MODE ALL DAY 5 BLACK MASK ON POSITION 6 DEFAULT Al 7 RETURN RET 1 Position the flashing box to the desired area then press SET 2 Adjust the size of the area then press SET 3 Once you have the desired location and size of the HSBLC AREA set choose RET Return to apply changes Choose AGAIN to star
5. always displayed in black and white You can turn on or off the burst signal on B W mode Automatic switching does not occur BURST Alters the color burst information passed to the video monitor Since this is B W mode it doesn t effect color but can effect gain IR SMART The IR SMART menu lets you select an area on screen where IR light can be detected The LEVEL slidebar controls signal gain in the area you define gt EXT This mode is used for cameras that have an external D N filter typically IR LED equipped cameras El 1 Clinton Electronics Corp NXHD User Manual NR This function reduces background image noise in a low light environment improving visibility MAIN MENU 1 LENS DCd 2 EXPOSURE a 3 WDR OFF 4 WHITEBAL ATW 5 DAY NIGHT AUTO 4 7 SPECIAL 8 ADJUST 9 RESET 10 EXIT 2D amp 3D NR 1 2DNR ON 2 3DNR ON l 3 RETURN RET From the main menu scroll to NR and press the SET button to access the sub menu gt 2DNR Reduces noise in the brightness of the image gt 3DNR Reduces noise caused by movement SMART NR Activates amp deactivates 2DNR amp 3DNR automatically depending on the environment Activates only when motion is present detected LEVEL The higher the level the more noise is filtered out S LEVEL Set the start level of the 3DNR function E LEVEL Set the end level of the 3DNR function 3DNR SMART NR OFF 2 LEVEL muaa 85 3
6. flicker which can happen when there is a clash with the frequency of the installed lighting MANUAL You can control the shutter speed manually 1 240 1 50 000 x2 x30 gt AGC Auto Gain CONTROL The higher the gain level the brighter the screen but the higher the noise gt SENS UP During low light situations the camera will automatically detect the light level and maintain a clear picture if this mode is activated OFF Deactivates the SENS UP function AUTO Activates the SENS UP function SENS UP may be disabled depending on manual SHUTTER settings When SENS UP is set to AUTO mode you can adjust the brightness by in creasing or decreasing the shutter speed x2 x30 The higher the SENS UP level the brighter the screen but the more likely it is that an after image will appear Possible image blur is normal with increased zoom while using SENS UP Clinton Electronics Corp NXHD User Manual o 6 EXPOSUR gt BRIGHTNESS Adjusts the video brightness 1 100 gt BLC This function is useful for adjusting areas of interest that appear too bright or too dark due to bright lighting conditions e BLC Back LIGHT COMPENSATION An area with a bright light source in the background can cause objects in the foreground to appear as silhouettes Use this setting to adjust the exposure of the image to properly expose the object in the foreground BLC ON BLC OFF GAIN
7. using 1 LENS DC y is present press the UP or DOWN 2 EXPOSURE l the SET button buttons 3 WDR OFF to enter the sub 4 WHITE BAL ATW 5 DAY amp NIGHT AUTO 4 6 NR Change the setting using the 7 SPECIAL LEFT or RIGHT 8 ADJUST buttons 9 RESET 10 EXIT 2 Scroll through menu items from the list available by using the UP or DOWN buttons 3 Use the LEFT or RIGHT buttons to change a setting 4 When finished select EXIT and press the SET button to save settings An item with the Pi icon also has sub menus To select a sub menu select an item with the icon and press the SET button An item with the icon is unavailable due to function settings After 30 seconds of no OSD activity the OSD menu will disappear All menu items have a RETURN option With this function you have the op tion to RET RETURN which takes you back to the previous menu screen Or you have to the option to END which saves current settings and exits out of the OSD Menu Some menu items only function when connected to an HD SDI monitor DVR If connected to an analog source ie analog test monitor the screen will display only black Press the LEFT or RIGHT button to de select the item 0 El Clinton Electronics Corp NXHD User Manual p Al a a a ct me FOCUS o Focus Zoom Cameras Only This function is only available on cameras equipped with a Auto Focus Zoom lens AF MODE SEMI 2 DISTA
8. NCE 0 3M 3 LENS REFRESH OFF 4 D ZOOM OFF 5 ZOOM DISPLAY OM 6 SMART ZOOM OFF 7 DIS 8 D EFFECT d 9 LENS INITIAL 10 RETURN From the main menu scroll to FOCUS and press the SET button to access the l sub menu gt AF MODE I SEMI The Focus will be adjusted automatically just after zoom in or out l AUTO The Focus will be adjusted automatically accord ing to the level of zoom MANUAL Manually adjust the focus of the lens gt DISTANCE The effective distance setting for focus control modes Auto Manual or SEMI Adjustable from 03M 0 5M 0 8M OM 1M 3M 5M 10M gt LENS REFRESH l Lens origin is regularly calibrated automatically Select between per forming either every day to every 10 days gt D ZOOM DicitaL Zoom Enable and adjust the level of digital zoom gt ZOOM DISPLAY I Display the level of zoom O Optical Zoom D Digital Zoom gt SMART ZOOM l Motion activated Digital Zoom x1 x10 to a specified area Useful for zooming to an area of interest such as a doorway while still being able to monitor the surrounding area i Auto Focus Zoom Cameras Only J Clinton Electronics Corp NXHD User Manual o 4 p rer ey ey ey o o o o gt FOCUS Auto Focus Zoom Cameras Only l gt DIS DiciTaL IMAGE STABILIZER This function mitigates any picture movement due to external factors such as wind or building vibration gt D EFFECT FREEZE Pau
9. S LEVEL CO O 4 E LEVEL CA Q 5 RETURN RET When adjusting the noise reduction level in 3DNR mode remember that the higher the level is set the greater the reduction in noise level as well as the brightness of the image Clinton Electronics Corp NXHD User Manual A El ECIAL This function includes special features that allow you to assign a name for the camera highlight motion events as well as adding privacy masks and the option to change the language displayed From the main menu scroll to SPECIAL and press the SET button to access the sub menu gt CAM TITLE Use this feature if you want to quickly identify a given image by assigning a title that will display on screen A Camera Title 0123456789 ABCDEFGHIJK E LMNOIPQRSTUV FRONT DOOR WXYZPret4 TOURS 7 CLR POS END 1 Select CAM TITLE then use the LEFT RIGHT button to set it to ON and then press the SET button 2 Use the 4 direction buttons to move to a desired letter and select the letter by pressing the SET button Repeat this to enter multiple letters You can enter up to 15 letters 3 Enter a title move the cursor to POS and press the SET button The entered title appears on the screen Select the position to display the title on the screen by using the 4 direction buttons and press the SET button 4 When the position is determined select END and press the SET button to return to the SPECIAL menu W
10. e subject is dim 3 If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically the WHITE BALANCE operation may become unstable Clinton Electronics Corp NXHD User Manual Aa 0 amp NIGHT This function displays images in color or B W In AUTO mode the camera will automat ically transition to B W to allow for clearer low light images This also allows cameras equipped with infrared illuminators to provide clear images in low light or no light sit uations DELAY TES 2 D N AGC rfi 27 1 LENS DC 4 2 EXPOSURE d 3 WDR OFF 4 WHITE BAL ATW 5 DAY amp NIGHT AUTO 4 3 N D AGC juran 20 4 RETURN RET 6 NR d 7 SPECIAL d 8 ADJUST d 9 RESET d 10 EXIT d From the main menu scroll to DAY amp NIGHT and select a desired mode using the Left or RIGHT buttons according to the picture display you want gt AUTO The mode is switched to COLOR in a normal environment but switches to B W mode when ambient illumination is low DELAY Sets a delay time before the switch is made from day to night night to day Useful if the camera is placed in an area that is subject to shadows or intermittent light level changes D gt N N gt 3D LEVEL Set the light level that triggers automatic switching COLOR from day to night night to day The image is always displayed in color Automatic switching does not occur gt B W The image is
11. function allows the ability to adjust the color temperature based on colors being emitted from different light sources Illumination is generally referred to as color tem perature which is represented in a measurement of kelvin K 9000 10000 K Rainy ED EQ Cloudy fi E 6500 8000 K 5000 6500 K Partly Cloudy HG 5000 5500 K gt Sunny 4000 5000 K Fluorescent lamp gp 3000 4000 k Wi Halogen lamp 2500 3500 K Tungsten lamp A 1000 2000 K 4 Candlelight From the main menu scroll to WHITE BAL and select one of the 4 following modes using the Left or Right buttons gt ATW Auto TRACKING WHITE BALANCE Select this to automatically readjust the white balance each time a change in the ambient color temperature is detected gt AWC gt SET Select this to find the optimal luminance level for the current environment point the camera towards a sheet of white paper and press the SET button gt MANUAL Select this to fine tune white balance manually Red Blue gain values adjustable gt AWB Auto White BALANCE Select this to set the white balance for only one particular environment More accurate then ATW but has to be reset manually when there is a change in ambient color temperature WHITE BALANCE may not work properly under the following conditions 1 When the color temperature of the environment surrounding the subject is out of the control range ie clear sky or sunset 2 When the ambient illumination of th
12. he selected area to the desired location then press SET 2 Adjust the size of the area then press SET 3 Once you have the desired location and size of the PRIVACY area choose RET Return to apply changes Choose AGAIN to start over to make any needed adjustments to the area COLOR Select from 16 different colors TRANS Adjust the transparency of the color DEFAULT Restores default PRIVACY settings Clinton Electronics Corp NXHD User Manual A 16 ECIAL gt LANGUAGE Choose from English Japanese Chinese Korean German Francais Italiano Espa ol Polish Russian Portugu s Dutch Turkish Hebrew or Arabic Scroll LEFT or RIGHT to the desired language and press the SET button to apply language to the OSD menu gt DEFECT Sensors could have defects for something wrong in the process of their storage or manufacturing process Such defects are called dead pixels which consist of two types static dead pixel and dynamic dead pixel The first can be found from the beginning while the second is found over time after using sensors for a certain period of time Dynamic dead pixels may not be visible on the screen of ordinary illumination However they can be made visible by amplifying the analog digital gain Dead pixel correction DPC corrects such defects LIVE DPC Automatic Dead Pixel Correction LEVEL Level of auto Dead Pixel Correction STATIC DPC Manual Defect OFF ON START Star
13. hen the CAM TITLE menu is OFF no title will be displayed on the monitor even if you enter one If you move the cursor to CLR and press the SET button all the letters are deleted To edit a letter move the cursor to the bottom left arrow and press the SET button Next move the cursor over the letter to be edited then move the cursor to the letter to be inserted and then press the SET button 1 E Clinton Electronics Corp NXHD User Manual SPECIAL gt D EFFECT FREEZE Pause the image or reactivate it MIRROR You can reverse flip the image from the camera on your monitor MIRROR Vertical flip V FLIP Both horizontal and vertical flip ROTATE Horizontal flip MIRROR D ZOOM Enable and adjust the level of digital zoom SMART ZOOM Motion activated Digital Zoom x1 x10 to a specified area Useful for zooming to an area of interest such as a doorway while still being able to monitor the surrounding area Enabling any one of the Digital Zoom effects D ZOOM or Smart Zoom will disable the other one IE if Smart Zoom is enabled D Zoom will be disabled Using Smart Zoom of D Zoom will disable make in active WDR Picture quality degrades when using the digital zoom functions Clinton Electronics Corp NXHD User Manual A 4 SPECIAL gt MOTION Monitor activity more efficiently with this feature by means of highlighting moving objects with a color overlay and displaying the word
14. inst harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense DISCLAIMER Clinton Electronics reserves the right to change the contents of this manual without prior notice WARNING Changes or modifications not expressly approved by the manufac turer could void the user s authority to operate the equipment CAUTION To prevent electric shock and risk of fire hazards Do NOT use power sources other than that specified Do NOT expose the inside of this appliance to rain or moisture This installation should be made by a qualified service person and should conform to all local codes The camera requires periodic inspection Contact an authorized technician to carry out the inspection Do not install the camera on a surface that can not support it If the camera is installed on an inappropri ate surface it may fall and cause injury AN AN Do not disassemble the camera It may result in an electric shock or other hazards AN TAUN Do not touch the front lens of the camera This is one of the most imp
15. ions and settings can be adjusted or changed by activating the OSD menu When the OSD menu is activated text will display on the monitor The user can then move the cursor to the desired function to change the setting set e AUTO FOUCS e DIGITAL ZOOM SMART ZOOM e DIS EJE INDOOR OUTDOOR gt tee e SHUTTER e AGC e SENS UP e BRIGHTNESS BLC e HSBLC e ACCE e DEFOG OFF ON e ATW AWC gt SET MANUAL AWB e AUTO e COLOR B W EXT e 2DNR gt 3DNR Pido CAM TITLE D EFFECT MOTION e PRIVACY LANGUAGE DEFECT e UTC MODE AIl e SHARPNESS MONITOR LSC e RESOLUTION FRAME RATE NN FACTORY EXIT b Auto Focus Zoom Cameras Only 0 El Clinton Electronics Corp NXHD User Manual ACCESSING THE OSD Settings can be adjusted using the built in joystick button pad optional CE RE MOTE or the optional UTC Up The Coax REMOTE Joystick use Press directly down on the joystick to activate the OSD menu Button pad use Press the SET button to activate the OSD menu CE REMOTE use Plug the remote into port serue located on the camera Press the SETUP button to activate the OSD menu CE REMOTE sold separately not available for every model Clinton Electronics Corp NXHD User Manual o 2 OSD MENU SETTINGS 1 Press the SET button Settings can only be changed when the OSD menu is displayed on the monitor Select the m When an arrow function
16. lens limitations gt VIDEO OUT Select NTSC or PAL composite video signal gt RESOLUTION Select either HD 720 or FULL HD 1080 composite video signal gt FRAME RATE Select the desired frame rate 30p 6Op 60i RESET From the main menu scroll to RESET and press the SET button to reset all camera settings to the factory default settings EXIT From the main menu scroll to EXIT and press the SET button to exit from the OSD menu Clinton Electronics Corp NXHD User Manual A E TROUBLESHOOTING If you have trouble operating your camera refer to the following table If the guidelines do not enable you to solve the problem contact Clinton Electronics Technical Support at 1 800 549 6393 or 815 633 1444 Problem Solution Nothing appears on the Check the power connection screen Check the video signal line connection HD SDI Composite When the camera s HD SDI BNC output is directly connected to the DVR s or mon itor s BNC terminal Make sure the DVR or monitor supports HD SDI signal input HD SDI output is converted into other for mat such as HDMI DVI or VGA by using a video converter Make sure the converter s HD SDI input format supports the product s output video format The video image is not clear Check if the lens is clean Clean the lens with a clean cloth Adjust the contrast feature of the monitor Make sure that the screen is not exposed di rectly to a bright light Move
17. milarities end Analog cameras will not work on HD SDI DVRs and HD SDI cameras will not work on Analog DVRs When in doubt test the cable Before you suspect the HD SDI camera or DVR is defective please check the device with a short piece of coax cable to make sure it is not the cable run causing the trouble We are here to help If you need further help call Clinton Electronics Technical Support toll free at 800 549 6393 CE SDIEXT CE SDIGEN CE SDITEST sold separately El El Clinton Electronics Corp NXHD User Manual CONTACT 2a CCTV Sales 1 800 447 3306 ta CCTV Support 1 800 549 6393 y H O o www clintonelectronics com Paas Address 6701 Clinton Road Loves Park IL 61111 Clinton Electronics Corp NXHD User Manual a El Make sure you read this manual before using the camera Store this manual safely so that you can use it in the future Please use this manual along with the Installation Manual included with the camera Clinton Electronics Corp 6701Clinton Road Loves Park IL 61111 Sales 1 800 447 3306 Support 1 800 549 6393 www clintonelectronics com ver 02 2714
18. ortant parts of the camera Be careful not to leave finger prints on the lens cover Do not install the camera under unstable lighting conditions Severe lighting change or flicker can cause the camera to work improperly Do not expose the camera to radio activity If exposed to radioactivity the CCD will fail Stop using your camera if you find it malfunctioning If the camera emits smoke or is unusually hot for a long period a fire may be caused AM Do not hold plug with wet hands It could cause an electric shock Do not use the camera close to a gas Cla EELS It may result in a fire or other hazards A Do not install the camera in extreme temperature conditions Only use the camera under conditions when temperatures are between 20 F 122 F Be especially careful to provide ll when operating under high temperatu Ss Do not drop the camera or subject it to physical shocks It can damage the housing compromising weather resistance A A AN Never keep the camera pointed directly at strong light It can damage the CCD AS TABLE OF CONTENTS ACCESSING THE OSD OSD MENU SETTINGS FOCUS Auto Focus Zoom Cameras Only LENS WDR Wide Dynamic Range WHITE BAL DAY amp NIGHT NR Noise Reduction SPECIAL ADJUST RESET EXIT TROUBLESHOOTING 01 02 03 04 05 06 09 10 11 12 13 18 18 18 19 OSD On Screen Display MENU Camera funct
19. se the image or reactivate it MIRROR You can reverse flip the image from the camera on your monitor MIRROR Vertical flip V FLIP Both horizontal and vertical flip ROTATE Horizontal flip V FLIP gt LENS INITIAL Lens origin is calibrated by controlling Enabling any one of the Digital Zoom effects D ZOOM Smart Zoom or DIS will disable the other two IE if Smart Zoom is enabled D Zoom and DIS will be disabled Using Smart Zoom of D Zoom will disable make in active WDR Picture quality degrades when using the digital zoom functions l Auto Focus Zoom Cameras Only LENS From the main menu scroll to LENS and press the SET button to access the sub menu gt INDOOR Select for indoor installations Fixed electronic shutter gt OUTDOOR Select for outdoor installations Automatic electronic shutter 0 E Clinton Electronics Corp NXHD User Manual EXPOSUR This function allows for the control of the amount of light that enters the camera Too much light results in a washed out image 1 SHUTTER AUTO 2 AGC ia 15 3 SENS UP Al d 4 BRIGHTNESS mjm 40 5 BLC OFF From the main menu scroll to EXPOSURE and press the SET button to access the sub menu gt SHUTTER Selectable automatic or manual shutter speeds AUTO Select this to control the shutter speed automatically depending on the ambient illumination of the subject FLK Select this when you experience picture
20. t Defect compensation follow the on screen instructions LEVEL Level of Manual Defect SENS UP Compensates for defects while SENS UP is activated The higher the level the more defects will be compensated Dead pixels are very rare and almost never occur and when they do it usually takes years before they develop Unfortunately there is no way to predict their occurrence but when and if they do it s very uneconomical to replace a good camera because a tiny pixel is locked permanently white for instance Most users will never use this feature gt UTC MODE Set to MODE 2 if using CE REMOTE UTC Camera must be connected to an ANALOG source such as a test monitor to use the CE REMOTE UTC While connected to analog some camera OSD features will not display correctly CE REMOTE UTC sold separately Clinton Electronics Corp NXHD User Manual This function provides additional options to help with how the image is displayed on the screen From the main menu scroll to ADJUST and press the SET button to access the sub menu gt SHARPNESS The outline of the image becomes cleaner and more distinctive as the SHARPNESS level increases If you increase the SHARPNESS level too high the picture may become distorted or noise may appear gt MONITOR Select to adjust for LCD or CRT monitors adjustable gain levels gt LSC Lens SHADING COMPENSATION Select to adjust for smoke tinted domes or image vignetting caused by
21. t over to make any needed adjustments to the area LEVEL Adjust the level of the HSBLC function The lower the level the more sensitive the HSBLC function becomes MODE Adjust when the HSBLC is active All Day or Night BLACK MASK Turn ON or OFF the HSBLC mask DEFAULT Restores default HSBLC settings e For effective license plate observation it needs minimum illumination and fast shutter speed more than 1 200sec Clinton Electronics Corp NXHD User Manual o E EXPOSUR gt ACCE Apaptive CoLorR Contrast ENHANCEMENT Enhance the overall color contrast of the image gt DEFOG Images in extraordinary environments such as fog or rain or in a very strong luminous intensity have DR dynamic range lower than ordinary images This function is a contrast enhancement which is used to overcome such shortcomings DR Wide Dynamic Range This function illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas WDR OFF WDR mode will not function when the camera is connected via the ANALOG connection WDR mode is an HD SDI only function If connected to the ANALOG connection the screen will go black when se lecting WDR Press Right or Left on the joystick to select a different option 0 El Clinton Electronics Corp NXHD User Manual WHITE BALANCE This
22. the camera if necessary The screen is dark Adjust the contrast feature of the monitor Adjust the BRIGHTNESS level of the EXPO SURE If you have an intermediate device set the 75Q Hi z properly and check the terminals There is a problem with the Check if an appropriate power source to camera operation The cam the camera complies with the manufactur era surface is too hot and er s standard requirement or if the voltage black stripes appear on the keeps changing screen 1 El Clinton Electronics Corp NXHD User Manual TROUBLESHOOTING Problem Solution The MOTION function is not working Colors are not quite right The screen is flickering COLOR Day amp Night mode is not working SENS UP function is not working Check if the DISPLAY mode is turned on Check if the SENSITIVITY level is too low Check the WHITE BAL setting Perform AWC gt 3SET Check if the camera is facing directly into sunlight or fluorescent light Move the cam era if necessary Set Shutter to FLK Flicker HD SDI video may not appear to be normal if distance exceeds the maximum transfer able distance When a BNC cable adapter is used to com bine two or more BNC cables for distributed HD SDI video transfer make sure the im pedance of the adapter is 750 Otherwise it may cause shorter transfer distance or broken video transfer Check the delay in the DAY amp NIGHT AUTO sub menu
23. ving the cart ap paratus combination a to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified ser vice personnel Servicing is required when the apparatus has been dam aged in any way such as power sup ply cord or plug is damaged liquid has been spilled or objects have fall en into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped CAUTION AN RISK OF ELECTRIC SHOCK DO NOT DISASSEMBLE TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT DISASSEMBLE NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alerttheusertothe presence of important operating and maintenance servicing instructions in the literature accompanying the appliance In USA and Canada Use Class 2 Power Supply Only INFORMATION This equipment has been tested and found to comply with lim its for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection aga
Download Pdf Manuals
Related Search