Home

Manual - Assurance Overhead Doors of Tulsa

1. INSTALLATION Position and Mount the Garage Door Opener Attach the Emergency Release Rope ana Handle ere ettet eerte Install Power Door Lock Attach the Cable Tension Monitor Required iere Install the Door Control MyQ Control Panel Install Remote Light Introduction 2 we Install the Protector System 13 Connect Power eeeeeeee 16 Install the Battery Backup optional 18 ADJUSTMENT 19 Program the Travel Limits 19 Set tlie POM cote eos 20 Test the Safety Reversal System 21 Test the Protector System 21 Test Cable Tension Monitor 22 Test Power Door Lock 22 To Open the Door Manually 22 OPERATION 23 Using Your Garage Door Opener 23 Using the Door Control MyQ Control Panel 24 Using the Remote Control 25 PROGRAMMING 26 To Add a Remote Control Keyless Entry or MyQ Enabled Accessories using the Door Control MyQ Control Panel 26 Internet Gateway Not Provided 21 Safety Symbol and Signal Word Review This garage door opener has been designed and tested to offer safe service provided it is installed operate
2. 1 FLASH Safety reversing sensors wire open broken or disconnected OR 2 FLASHES Safety reversing sensors wire shorted or black white wire reversed 3 FLASHES Door control or wire shorted 4 FLASHES Safety reversing sensors slightly misaligned dim or flashing LED 5 FLASHES Motor RPM is not recognized 9 FLASHES Cable tension monitor reversal 10 FLASHES Limits and forces need reprogramming 11 FLASHES Limits and forces need reprogramming 12 FLASHES Attempting to compensate 13 FLASHES Attempting to compensate Safety Reversing Sensor SYMPTOM One or both of the Indicator lights on the safety sensors do not glow steady e Inspect sensor wires for a short staple in wire correct wiring polarity black white wires reversed broken or disconnected wires replace attach as needed e Disconnect all wires from back of garage door opener e Remove sensors from brackets and shorten sensor wires to 1 2 ft 30 60 cm from back each of sensor e Reattach sending eye to garage door opener using shortened wires If sending eye indicator light glows steadily attach the receiving eye e Align sensors if the indicator lights glow replace the wires for the sensors If the sensor indicator lights do not light replace the safety reversing sensors SYMPTOM The door doesn t activate from the door control e Inspect door control wires for a short staple in wire replace as neede
3. IMPORTANT NOTE Model 580LM Alternate Power Supply may be installed if an outlet is not located near the garage door opener MyQ light controls will continue to work however all other MyQ devices Internet Gateway and TTC WILL NOT work if using the Model 580LM Alternate Power Supply If you would like to use these features contact an electrician to install an outlet near the garage door opener Red Learn LED To Erase All Codes From the Door Control MyQ Control Panel Memory Erase all remote controls and keyless entries 1 Press and hold the LEARN button on the control panel until the red learn LED goes out approximately 6 seconds All remote control and keyless entry codes are now erased Reprogram any compatible accessory you wish to use Erase all devices including MyQ enabled accessories 1 Press and hold the LEARN button on the control panel until the red learn LED goes out O approximately 6 seconds L JJ 2 Immediately press and hold the LEARN button again until the red learn LED goes out All codes are now erased Reprogram any compatible accessory you wish to use 27 Programming Reprogramming Light or Additional Light Your garage door opener remote light has already been programmed at the factory to operate with your opener Any additional or replacement remote lights will need to be programmed 1 Press the LEARN button on the light until the LED comes ON 2 Activ
4. HARDWARE Insulated Staples dinnnnnnnnnnn Not shown Screw 6ABx 1 1 4 Standard installation 2 um gt a ATTA Screw 6 32x1 pre wired 2 Drywall Anchors 2 To insert or p Ga release wire d push in tab with screwdriver tip Q WHT Red White WHT RED Installation IMPORTANT INSTALLATION INSTRUCTIONS A amp WARNING To reduce the risk of SEVERE INJURY or DEATH 1 This portable luminaire has a polarized plug one blade 5 NEVER use with an extension cord unless plug can be is wider than the other as a feature to reduce the risk of fully inserted electric shock 6 DO NOT alter the plug 2 This plug will fit in a polarized outlet ONLY one way 7 Light is intended for ceiling mount and indoor applications 3 If the plug does not fit fully in the outlet reverse the plug ONLY 4 If it still does not fit contact a qualified electrician 6 Install Remote Light HARDWARE CAUTION The remote light garage door opener light wai Anchor 2 To prevent possible OVERHEATING of is designed to plug directly into a standard the endpanel or light socket 120V outlet Select an appropriate location z D DO NOT use short neck or specialty on the ceiling to mount the light within 6 light bulbs feet 1 83 m of an electrical outlet so that Light Clip
5. m 1 1 2 3 8 cm board or a 2x4 laid flat 4 amp WARNING Without a properly installed safety reversing sensor persons particularly small children could be SERIOUSLY INJURED or KILLED by a closing garage door Adjustment 5 Test Cable Tension Monitor If your cable tension monitor has been activated the LED on the garage door opener will blink 9 times 5 Test Power Door Lock 1 With the door fully closed the power door lock bolt should be protruding through the track 2 Operate the door in the open direction The power door lock should retract before the door begins to move 3 Operate the door in the down direction When the door reaches the fully closed position the power door lock should automatically activate to secure the door NOTE If the power door lock does not function the lock can be manually released by sliding the manual release handle to the open position 7 To Open the Door Manually Disengage door lock before proceeding The door should be fully closed if possible Pull down on the emergency release handle until a click noise is heard from the garage door opener and lift the door manually To reconnect the door to the garage door opener pull the emergency release handle straight down a second time until a click noise is heard from the garage door opener The door will reconnect on the next UP or DOWN operation Test the emergency release 1 Make sure the ga
6. The Chamberlain Group Inc 845 Larch Avenue g Elmhurst Illinois 60126 1196 ELITE SERI ES www liftmaster com Os Model 8500 GARAGE DOOR OPENER For Residential and Light Duty Commercial Use Install On Sectional Doors With Torsion Assemblies Only This product is intended for installation only by trained garage door technicians This product may require adjustments to door springs and or track configurations This product is not intended for use on low headroom tracks or garage doors utilizing extension springs Please read this manual and the enclosed safety materials carefully Wi Fasten the manual near the garage door after installation The door WILL NOT CLOSE unless the Protector System and cable tension monitor are connected and properly aligned Periodic checks of the garage door opener are required to ensure safe operation The model number label is located behind the hinged door of your opener DO NOT exceed 10 complete cycles of door operation per hour This garage door opener is ONLY compatible with MyQ and Security 2 0 accessories Table of Contents INTRODUCTION Safety Symbol and Signal Word Review Plains acit cias Preparing Your Garage Door Tools Need di tts Carton Inventory sseese PAR CWANG ssi cec ande der neas ASSEMBLY Attach the Collar to the Garage Door Opener Attach Mounting Bracket to Garage Door Opener
7. DQ O J A 7 16 WHT 11 mm WHT BLK Bell wire Installation 8 Connect Power To avoit installation difficulties do not run the garage door opener at this time To reduce the risk of electric shock your garage door opener has a grounding type plug with a third grounding pin This plug will only fit into a grounding type outlet If the plug doesn t fit into the outlet you have contact a qualified electrician to install the proper outlet There are two options for connecting power OPTION A TYPICAL WIRING 1 OPTION B PERMANENT WIRING A WARNING To prevent possible SERIOUS INJURY or DEATH from electrocution or fire Be sure power is NOT connected to the opener and disconnect power to circuit BEFORE removing cover to establish permanent wiring connection e Garage door installation and wiring MUST be in compliance with ALL local electrical and building codes NEVER use an extension cord 2 wire adapter or change plug in ANY way to make it fit outlet Be sure the opener is grounded Plug in the garage door opener into a grounded outlet DO NOT run garage door opener at this time IMPORTANT NOTE The model 580LM Alternate Power Supply may be installed if an outlet is not located near the garage door opener MyQ light controls will continue to work however all other MyQ devices and TTC WILL NOT work if using the Model 580LM Alternate Po
8. Light Lens Installation 1 Install the Protector System The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction This is a required safety device and cannot be disabled IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR When properly connected and aligned the safety reversing sensor will detect an obstacle in the path of its electronic beam The sending eye with an amber indicator light transmits an invisible light beam to the receiving eye with a green indicator light If an obstruction breaks the light beam while the door is closing the door will stop and reverse to full open position and the opener lights will flash 10 times The units must be installed inside the garage so that the sending and receiving eyes face each other across the door no more than 6 inches 15 cm above the floor Either can be installed on the left or right of the door as long as the sun never shines directly into the receiving eye lens The mounting brackets are designed to clip onto the track of sectional garage doors without additional hardware If itis necessary to mount the units on the wall the brackets must be securely fastened to a solid surface such as the wall framing Extension brackets see accessories are available if needed If installing in masonry construction add a piece of wood at each location to avoid drilling extra holes in masonry if repositioning
9. Wrench IMPORTANT INSTALLATION INSTRUCTIONS A amp WARNING To reduce the risk of SEVERE INJURY or DEATH READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS Install garage door opener ONLY on properly balanced and lubricated door An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH ALL repairs to cables spring assemblies and other hardware MUST be made by a trained door systems technician BEFORE installing garage door opener Disable ALL locks and remove ALL ropes connected to door BEFORE installing garage door opener to avoid 7 NEVER wear watches rings or loose clothing while installing or servicing the garage door opener They could be caught in door or operator mechanisms Install wall mounted door control within sight of the door out of reach of children at minimum height of 5 feet 1 5 m e away from ALL moving parts of the door Install the Entrapment Warning Placard next to the door control in a prominent location entanglement 10 Place manual release safety reverse test label in plain view Mount the emergency release within reach but at least 6 gn inside of goor feet 1 83 m above the floor and avoiding contact with 11 Upon completion of installation test safety reversal vehicles to avoid accidental release NEVER connect garage door opener to power source until instructed to do so system Do
10. of the garage floor e Any repair to or adjustment of the opener 4 Test the Protector System 1 Press the remote control push button to open the door 2 Place the opener carton in the path of the door 3 Press the remote control push button to close the door The door will not move more than an inch and the opener lights will flash The garage door opener will not close from a remote if the indicator light in either sensor is off alerting you to the fact that the sensor is misaligned or obstructed If the garage door opener closes the door when the safety reversing sensor is obstructed do not operate the door Call for a trained door systems technician A A A V A A V V c AAA AAA ERA PALS Ades Safety Reversing Sensor Safety Reversing Sensor 21 4 amp WARNING Without a properly installed safety reversal system persons particularly small children could be SERIOUSLY INJURED or KILLED by a closing garage door e Safety reversal system MUST be tested every month e f one control force or travel limits is adjusted the other control may also need adjustment After ANY adjustments are made the safety reversal system MUST be tested Door MUST reverse on contact with 1 1 2 3 8 cm high object or 2x4 laid flat on the floor E
11. screws to secure the mounting bracket to the wall Secure the antenna wire with a staple to prevent antenna from being entangled in a door roller FIGURE 1 Bearing Plate Collar Screws Set Screws 3 16 Hex Key Wrench Screws 14 10x1 7 8 4 amp WARNING To prevent possible SERIOUS INJURY or DEATH e Concrete anchors MUST be used if mounting bracket into masonry e NEVER try to loosen move or adjust garage door springs cables pulleys brackets or their hardware ALL of which are under EXTREME tension e ALWAYS call a trained door systems technician if garage door binds sticks or is out of balance An unbalanced garage door might NOT reverse when required Operator MUST be mounted at a right angle to the torsion bar to avoid premature wear on the collar HARDWARE 14 10x1 7 8 Hex Screws 2 Insulated Staples Not shown Installation 2 Attach the Emergency Release Rope and Handle 1 Thread one end of the rope through the hole in the top of the red handle so NOTICE reads right side up as shown Secure with an overhand knot at least 1 inch 2 5 cm from the end of the rope to prevent slipping Thread the other end of the rope through the loop in the emergency release cable Adjust rope length so the handle is no higher than 6 feet 1 83 m above the floor Secure with an overhand knot NOTE If it is nec
12. up to 20 times without power Door loses limits e Collar not tightened securely Tighten collar see Assembly Steps 1 and 2 and reprogram limits see Adjustment Step 1 The garage door opener moves when the door is in operation e Some minor movement is normal for this product If it is excessive the collar will wear prematurely e Check to make sure the torsion bar is not moving left right excessively e Check to make sure the torsion bar is not visibly moving up and down as it rotates e Check that the opener is mounted at a right angle to the jackshaft If not move the position of the mounting bracket Power lock makes noise when operating e Call LiftMaster dealer for replacement power lock 32 Repair Parts Installation Parts KEY PART KEY PART NO NO DESCRIPTION NO NO DESCRIPTION 1 888LM MyQ Control Panel 10 4146388 Collar with set screws 2 2 895MAX 3 Button MAX remote control 11 41A6102 Power door lock 3 10A19 3V2016 lithium battery 12 41A5266 1 Safety sensor brackets 2 4 290151 Remote control visor clip 13 380LM Remote Light garage door opener light 5 4144582 Emergency release rope amp handle assembly 14 41D96 1 Light lens for light 6 41B4494 1 2 Conductor bell wire white amp white red NOT SHOWN 7 41A6104 Cable tension monitor 101D173 Push bar for door control 8 4100902 Mounting bracket 41A6288 Hardware bag for light 9 4145034 Safety sensor kit receiving and sending 4146298 Ins
13. 1 1 2 high 3 8 cm object or 2x4 laid flat on floor CAUTION To prevent damage to vehicles be sure fully open door provides adequate clearance a ERE YELLOW YELLOW EL LL GL cy Adjustment 2 Set the Force The force setting measures the amount of force required to open and close the door 1 Push the yellow button twice to enter into the Force Adjustment Mode The LED will flash quickly Push the door control or programmed remote control The door will close DOWN Push the door control or programmed remote control again The door will open UP Push the door control or programmed remote control a third time to close the door DOWN The LED will stop flashing when the force has been programmed The door must travel through a complete cycle up and down in order for the force to be set properly If the garage door opener cannot open and close the door fully inspect the door to ensure that it is balanced properly and is not sticking or binding If the door is not stopping exactly where you would like it repeat Program the Travel Limits Push yellow button twice to enter garage door opener into Force Adjustment Mode 20 4 amp WARNING Without a properly installed safety reversal system persons particularly small children could be SERIOUSLY INJURED or KILLED by a closing garage door
14. BACKUP SYSTEM The Chamberlain Group Inc Seller warrants to the first retail purchaser of this product for the residence in which this product is originally installed that it is free from defects in materials and or workmanship for a period of five years from the date of purchase except that the motor is warranted to be free from defects in materials and or workmanship for the lifetime of the product while you own your residence and the Battery Backup System is warranted to be free from defects in materials and or workmanship for a period of one year from the date of purchase The proper operation of this product is dependent on your compliance with the instructions regarding installation operation and maintenance and testing Failure to comply strictly with those instructions will void this limited warranty in its entirety If during the limited warranty period this product appears to contain a defect covered by this limited warranty call 1 800 528 9131 toll free before dismantling this product You will be advised of disassembly and shipping instructions when you call Then send the product or component pre paid and insured as directed to our service center for warranty repair Please include a brief description of the problem and a dated proof of purchase receipt with any product returned for warranty repair Products returned to Seller for warranty repair which upon receipt by Seller are confirmed to be defective and covered by this lim
15. Door stops while opening e Garage door opener will try to compensate three times before turning to a 11 Flash 30 Troubleshooting Troubleshooting The garage door doesn t operate from the MyQ Home Control App or website e When using Model 580LM Alternate Power Supply or when in Battery Backup mode the Internet Gateway will not activate the garage door through the MyQ Home Control App If you wish to use the Internet Gateway with your garge door opener please contact your local electrican to wire an outlet next to the garge door opener The garage door opener doesn t operate from either the Door Control or the remote control e Does the garage door opener have electric power Plug a lamp into the outlet If it doesn t light check the fuse box or the circuit breaker Some outlets are controlled by a wall switch e Have you disabled all door locks Review installation instruction warnings on page 7 e sthere a build up of ice or snow under the door The door may be frozen to the ground Remove any restriction e The garage door spring may be broken Have it replaced see page 3 for reference e Ifthe yellow command LED does not turn on reverse the wires connected to the RED and WHT terminals of the control panel Replace wire if necessary The yellow and red LEDs on the Door Control are blinking quickly e The control panel is charging and may take up to 5 minutes to become operational My remote control will not activate
16. OVER ANY PROBLEMS CAUSED BY INTERFERENCE UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE OR INABILITY TO USE THIS PRODUCT IN NO EVENT SHALL SELLER S LIABILITY FOR BREACH OF WARRANTY BREACH OF CONTRACT NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT Some states do not allow the exclusion or limitation of consequential incidental or special damages so the above limitation or exclusion may not apply to you This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state 2013 The Chamberlain Group Inc 114A4565C All Rights Reserved
17. Screw the Es amus are away from moving pere CR DO NOT use halogen bulbs Use parts ONLY incandescent S e 1 Install the hinge and latch clips Clips sx O TEND ul M EM iid d slide in between the metal plate and the USE iy ee QUIS plastic housing on each side of the light To provide an adequate visual alert the base garage door opener light bulb MUST be a minimum of 40 Watt or equivalent 2 Install screws into the ceiling leaving 1 8 inch 3 mm of the thread exposed NOTE If installing light on drywall and a ceiling joist cannot be located use wall anchors provided No pilot hole is required for wall anchors 3 Determine the length of power cord needed to reach the nearest outlet Wind any excess cord around cord retainer on the top side of the light base Wall Anchor 4 Install the light base by pushing onto the screws and turning the base clockwise to lock the light in place 5 Install two Type A19 incandescent or compact fluorescent bulbs 100 watt maximum per bulb 200 watts total NOTE Do not use LED bubs as they may reduce the range or performance of your remote control s 100 Watt max 6 Install the light lens by hooking one end of the lens over the hinge and pressing up on the other end to latch into place 7 Plugin the light to outlet NOTE Light will not operate until the garage door opener is activated Light Clip Screw cat
18. a certain number of openings remember that the test has used up one opening To clear the temporary password repeat steps 1 3 setting the number of hours or times to 0 in step 3 ONE BUTTON CLOSE The garage door opener can be closed by pressing only the ENTER button if the one button close feature has been activated This feature has been activated at the factory To activate or deactivate this feature press and hold buttons 1 and 9 for 10 seconds The keypad will blink twice when the one button close is active The keypad will blink four times when one button close is deactivated 28 Maintenance Care of Your Garage Door Opener MAINTENANCE SCHEDULE Once a Month e Manually operate door If it is unbalanced or binding call a trained door systems technician e Check to be sure door opens and closes fully Adjust limits and or force if necessary see Adjustment Steps 1 and 2 e Repeat the safety reverse test Make any necessary adjustments see Adjustment Step 3 Once a Year e il door rollers bearings and hinges The garage door opener does not require additional lubrication Do not grease the door tracks THE REMOTE CONTROL BATTERY The LED s on your remote control will stop flashing when the battery is low and needs to be replaced To replace battery open the case as shown Insert battery positive side up Replace the battery with only 3V2016 coin cell batteries Dispose of old battery properly Rem
19. allation Depending on your requirements additional materials may be required THIS GARAGE DOOR OPENER IS COMPATIBLE WITH Doors that use a torsion bar and springs The torsion bar must be 1 inch 2 5 cm diameter NOTE Inspect the torsion bar while the door is raised and lowered It is important that there is no noticeable movement up 4 6 inch 10 15 cm drums not to be used on tapered drums over 6 inches 15 cm High lift up to 54 inches 137 2 cm high and standard lift sectional doors up to 14 feet 4 3 m high Doors up to 18 feet 5 5 m wide Doors up to 180 sq ft 16 7 sq m Review or inspect proposed installation area The garage door opener can be installed on the left or right side of door Select the side that meets the requirements listed below a Must have minimum of 2 1 2 inches 6 4 cm between the garage wall and the center of the torsion bar Must have minimum of 3 inches 7 6 cm between the ceiling and the center of torsion bar Must have minimum of 8 inches 20 3 cm between the side garage wall or obstruction and the end of torsion bar The torsion bar must extend at least 1 5 inches 2 5 12 7 cm past the bearing plate This may vary depending on your installation requirements An electric outlet is required within 6 feet 1 83 m of the installation area If outlet does not exist contact a qualified electrician Depending upon garage construction extension brackets or w
20. asure and place right and left assemblies at the same distance out from the wall Be sure all door hardware obstructions are cleared 3 Fasten to the floor with concrete anchors as shown not provided Attach with E Concrete Anchors Safety Reversing Sensor Bracket Installation MOUNTING THE SAFETY REVERSING SENSORS 1 Slide a 1 4 20x1 2 carriage bolt head into the slot on each sensor 2 Use wing nuts to fasten safety reversing sensors to brackets with lenses pointing HARDWARE toward each other across the door Be sure the lens is not obstructed by a bracket Carriage Bolt extension 1 4 20x1 2 2 Mm 3 Finger tighten the wing nuts 1 4 20 2 Carriage Bolt Wing Nut lt WIRE THE SAFETY REVERSING SENSORS 1 Run the wire from both sensors to the garage door opener Attach the wire to the wall HARDWARE and ceiling with the staples A Insulated Staples 2 Strip 7 16 inch 11 mm of insulation from each set of wires Separate the wires Twist Not shown the white wires together Twist the white black wires together 3 Insert the white wires into the white terminal on the garage door opener Insert the white black wires into the grey terminal on the garage door opener To insert or remove the wires from the terminal push in the tab with a screwdriver tip pA CQ
21. ate the garage door opener using the hand held remote door control or keyless entry 3 The code has been programmed when the remote light comes on Additional Programming for the Keyless Entry Not Provided TO CHANGE AN EXISTING KNOWN PIN If the existing PIN is known it may be changed by one person without using a ladder 1 Press the four buttons for the present PIN then press and hold the button Release the button 2 Press the new 4 digit PIN you have chosen then press ENTER Test by pressing the new PIN then press ENTER The door should move TO SET A TEMPORARY PIN You may authorize access by visitors or service people with a temporary 4 digit PIN After a programmed number of hours or number of accesses this temporary PIN expires and will no longer open the door It can be used to close the door even after it has expired To set a temporary PIN 1 Press the four buttons for your personal entry PIN not the last temporary PIN then press and hold the button Release the button 2 Press the temporary 4 digit PIN you have chosen then press ENTER 3 To set the number of hours this temporary PIN will work press the number of hours up to 255 then press OR 3 To set the number of times this temporary PIN will open door press the number of times up to 255 then press Test by pressing the four buttons for the temporary PIN then press ENTER The door should move If the temporary PIN was set to
22. balanced or binding call a trained door systems technician e Clear any ice or snow from the garage floor area where the door closes e Review Adjustment Step 2 Repeat safety reverse test after adjustments My door will not close and the light bulbs blink The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction e Verify the safety sensors are properly installed aligned and free of any obstructions The garage door opener strains to operate door e The door may be out of balance or the springs may be broken Close the door and use the emergency release handle to disconnect the door Open and close the door manually A properly balanced door will stay in any point of travel while being supported entirely by its springs If it does not disconnect the garage door opener and call a trained door systems technician The garage door opener motor hums briefly then won t work e The garage door springs may be broken See above e ifthe problem occurs on the first operation of the garage door opener door may be locked Disable the power door lock The garage door opener won t operate due to power failure e Manually open the power door lock e Use the emergency release handle to disconnect the door The door can be opened and closed manually When power is restored pull manual release a second time e faBattery Backup is connected the opener should be able to operate
23. button the HOLD OPEN LED will turn solid The TTC will remain suspended until the HOLD OPEN button is pressed again or the garage door opener is activated from another device door control remote control keyless entry etc 24 LIGHTS Press the LIGHT button to turn the garage door opener lights on or off When the lights are turned on they will stay on until the LIGHT button is pressed again or until the garage door opener is activated Once the garage door opener is activated the lights will turn off after the specified period of time the factory setting is 4 1 2 minutes The LIGHT button will not control the lights when the door is in motion To change the amount of time the garage door opener lights will stay on Press and hold the LOCK button until the garage door opener lights flash The time interval is indicated by the number of flashes NUMBER OF TIMES GARAGE DOOR OPENER GARAGE DOOR OPENER LIGHTS FLASH LIGHT STAYS ON Light Feature The lights will turn on when someone enters through the open garage door and the safety reversing sensor infrared beam is broken Activate Start with the garage door opener lights on Press and hold the LIGHT button until the garage door opener lights turn off then on again Deactivate Press and hold the LIGHT button until the garage door opener lights turn on then off again Approximately 10 seconds TIME THE Operation Using the Remote Control Press an
24. c 10 Cycles per Hour gt Pliers Wire Cutters Tape Measure a 3 16 and 1 8 Hex Key Wrench Pencil Claw Hammer oe L Screwdriver ce 2 CA Adjustable End Wrench Needle Nose Pliers Torque Meter not shown Introduction Carton Inventory Accessories included with the garage door opener will vary depending on the model purchased If anything is missing carefully check the packing material Remote Control 3 Button Premium Remote Control Visor Clip Model 895MAX 1 White amp White Red Remote Light Garage Door Opener Light with Hardware Bag Door Control MyQ Control Panel Model 888LM Power Door Lock with 2 Conductor White amp White Black Bell Wire with Connector Collar with Screws The Protector System 2 Safety Reversing Sensors 1 Sending Eye and 1 Receiving Eye with 2 Conductor White amp White Black Bell Wire attached Safety Labels and Literature G Mounting Bracket Cable Tension Monitor with 2 Conductor Green White Bell Wires Moving Door Can Cause Serious Injury or Death Safety Reversing Sensor Bracket 2 Hardware Hex Screw 14 10x1 7 8 4 Self Tapping Screw 10 32 2 Screw 6x1 1 4 2 Drywall Anchor 2 Machine Screw 6x1 2 Wall Anchor Screw In 2 Carriage Bolt 1 4 20x1 2 2 Handle Wing Nut 1 4 20 2 Rope Pan Head Screw 1 4 20x1 2 2 Insulated Staples Hex Head Screw 8x1 2 Lock Temp
25. correctly When the light beam is obstructed or misaligned while the door is closing the door will reverse and the garage door opener lights will flash ten times If the door is already open it will not close The sensors can be aligned by loosening the wing nuts aligning the sensors and tightening the wing nuts 1 Check to make sure the LEDs in both sensors are glowing steadily The LEDs in both sensors will glow steadily if they are aligned and wired correctly If the receiving sensor is in direct sunlight switch it with sending sensor so it is on the opposite side of the door invisible light beam Sending Sensor Receiving Sensor IF THE AMBER LED ON THE SENDING SENSOR IS NOT GLOWING e Make sure there is power to the garage door opener e Make sure the sensor wire is not shorted broken e Make sure the sensor has been wired correctly white wires to white terminal and white black wires to grey terminal IF THE GREEN LED ON THE RECEIVING SENSOR IS NOT GLOWING e Make sure the sensor wire is not shorted broken e Make sure the sensors are aligned A us a ENSURE THE DOOR CONTROL IS WIRED CORRECTLY The yellow command LED and the red learn LED on the door control will blink quickly for up to 5 minutes as the door control recharges When the door control is operational the yellow command LED will glow steadily 17 Installation g Ins
26. d e Disconnect wires at door control touch wires together If garage door opener activates replace door control e f garage door opener does not activate disconnect door control wires from garage door opener Momentarily short across red and white terminals with jumper wire If garage door opener activates replace door control wires SYMPTOM Sending indicator light glows steadily receiving indicator light is dim or flashing Realign receiving eye sensor clean lens and secure brackets e Verify door track is firmly secured to wall and does not move SYMPTOM Door travels 2 3 inches and stops e Reprogram limits and forces See Adjustment section e fthe motor unit continues to travel 2 3 inches check the travel module connection or replace the travel module SYMPTOM No movement motor runs 2 3 seconds e Reconnect the emergency release e Motor may need to be replaced SYMPTOM Door stops and reverses while closing e Check for possible door obstructions and remove e Check that the cable tension monitor is properly connected to the opener e Replace the cable tension monitor SYMPTOM Door stops while opening e Reprogram limits and forces See Adjustment section SYMPTOM Door stops and reverses while closing e Reprogram limits and forces See Adjustment section SYMPTOM Door stops and reverses while closing e Garage door opener will try to compensate three times before turning to a 10 Flash SYMPTOM
27. d maintained and tested in strict accordance with the instructions and warnings contained in this manual When you see these Safety Symbols and Signal Words on the following pages they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them The hazard may come from something mechanical or from electric shock Read the warnings carefully When you see this Signal Word on the following pages it will alert you to the possibility of damage to your garage door and or the garage door opener if you do not comply with the cautionary statements that accompany it Read them carefully To Erase All Codes From the Door Control MyQ Control Panel MEMO aiti certet cms 27 Reprogramming Light or Additional Light 28 Additional Programming for the Keyless Entry Not Provided 28 MAINTENANCE 29 Care of Your Garage Door Opener 29 TROUBLESHOOTING 30 Diagnostic Ghart s 30 Troubleshooting ssss 31 Troubleshooting Continued 32 REPAIR PARTS 33 Installation Parts sss 33 Garage Door Opener Assembly Parts 34 ACCESSORIES 35 REPAIR PARTS AND SERVICE 36 WARRANTY 36 4 amp WARNING Mechanical A WARNING Electrical CAUTION Introduction Planning Survey your garage area to see if any of the conditions below apply to your inst
28. d hold the button down until the door or gate starts to move The remote control will operate from up to 3 car lengths away on typical installations Installations and conditions vary contact an installing dealer for more information 3 Button Remote Controls Additional buttons on the remote control can be programmed to operate up to 3 devices such as additional garage door openers light controls gate operators or access control systems NOTICE To comply with FCC and or Industry Canada IC rules adjustment or modifications of this transceiver are prohibited THERE ARE NO USER SERVICEABLE PARTS Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC rules and IC RSS 210 Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class B digital apparatus complies with Canadian ICES 003 25 Programming Your hand held remote control model 895MAX has already programmed to the door control MyQ Control Panel at the factory Below are instructions for programming additional remote controls keyless entries and MyQ enabled accessories to the door c
29. e NEVER learn forces or limits when door is binding or sticking Repair door first Too much force on garage door will interfere with proper operation of safety reversal system e After ANY adjustments are made the safety reversal system MUST be tested Door MUST reverse on contact with 1 1 2 high 3 8 cm object or 2x4 laid flat on floor Adjustment 3 Test the Safety Reversal System TEST 1 With the door fully open place a 1 1 2 inch 3 8 cm board or a 2x4 laid flat on the floor centered under the garage door 2 Operate the door in the down direction The door must reverse on striking the obstruction Upon successful safety reversal test proceed to Adjustment Step 4 ADJUST If the door stops on the obstruction it is not traveling far enough in the down direction Complete Adjustment Steps 1 and 2 Program the Travel Limits and Set the Force Repeat the test When the door reverses on the 1 1 2 inch 3 8 cm board or 2x4 laid flat remove the obstruction and run the garage door opener through 3 or 4 complete travel cycles to test adjustment If the garage door opener continues to fail the Safety Reverse Test call for a trained door systems technician IMPORTANT SAFETY CHECK Test the Safety Reverse System after e Each adjustment of limits or force controls e Any repair to or adjustment of the garage door including springs and hardware e Any repair to or buckling
30. ed with the Indicates the status of your garage door from inside or the MyQ control panel For instructions on garage door opener light bulbs the home and allows you to close an open garage door programming to the internet gateway refer to from inside the house the manual 26 Programming Internet Gateway Not Provided The LiftMaster Internet Gateway gives you control of your garage door from your internet connected computer or mobile device You must have your internet gateway registered to your customer account at www myliftmaster com in order to use it with the MyQ Control Panel Go to www myliftmaster com and follow the instructions to create an account and register your device if you have not already Model 828LM LiftMaster Internet Gateway To program your MyQ Control Panel to the LiftMaster Internet Gateway ee C N H A M PI d Devi 1 Goto www myliftmaster com from a computer or mobile device o RE 2 Click on Manage Places gt Add New Device gt Garage Door Opener and follow the My Gateway gt Add New Device directions Add New Place Step 1 Step 2 3 Once you click ADD you have 3 minutes to press the LEARN button two times on the Learn uten on your on MyQ control panel The red learn LED will turn on 4 The red learn LED will turn off when programming is complete Once the control ec e panel is learned it will appear on your screen You can then name the device e g My Control Panel etc
31. eight of 5 feet 1 5 m where small children cannot reach and away from the moving parts of the door For gang box installations it is not necessary to drill holes or install the drywall anchors Use the existing holes in the gang box NOTE Due to power consumption this door control Model 888LM cannot be used in conjunction with another wired door control connected to your garage door opener If an additional door control is needed the wireless door control model 885LM can be programmed to the door control Model 888LM 1 Strip 7 16 11 mm of insulation from one end of the wire and separate the wires 2 Connect wires to the door control Make sure the polarity is correct Red wire to the RED terminal White wire to the WHT terminal 3 Markthe location of the bottom mounting hole and drill a 5 32 4 mm hole 4 Install the bottom screw allowing 1 8 3 mm to protrude from the wall 5 Position the bottom hole of the door control over the screw and slide down into place 6 Liftthe push bar up and mark the top hole 7 Remove the door control from the wall and drill a 5 32 4 mm hole for the top screw 8 Position the bottom hole of the door control over the screw and slide down into place Attach the top screw 9 Run the white and red white wire from the door control to the garage door opener Attach the wire to the wall and ceiling with the staples not applicable for gang box or pre wired installations Do not p
32. er has already been programmed at the factory to operate with your remote control which changes with each use randomly accessing over 100 billion new codes MyQ technology uses a 900MHz signal to provide two way communication between the garage door opener and MyQ enabled accessories When programmed to the LiftMaster Internet Gateway you can monitor and control your garage door from any internet enabled computer or smartphone You may program up to 12 Security 2 0 remote controls 2 Security 2 0 keyless entries and a combination of 16 MyQ accessories to the MyQ control panel The garage door opener can be activated through a wall mounted door control remote control wireless keyless entry or MyQ accessory When the door is closed and the garage door opener is activated the door will open If the door senses an obstruction or is interrupted while opening the door will stop When the door is in any position other than closed and the garage door opener is activated the door will close If the garage door opener senses an obstruction while closing the door will reverse If the obstruction interrupts the sensor beam the garage door opener lights will blink 10 times However you can close the door if you hold the button on the door control or keyless entry until the door is fully closed The safety reversing sensors do not affect the opening cycle The safety reversing sensor must be connected and aligned correctly bef
33. ere in the home 825LM Remote Light Control Automatically control your lights using your garage door opener a SECURITY 2 07 remote control or a LiftMaster Internet Gateway Plugs into any interior outlet STANDARD ACCESSORIES 885LM Security 2 0 Wireless Door Control Push bar light feature and all auxiliary button Includes battery 891LM Single Button Remote Control Includes visor clip 893LM 3 Button Remote Control Includes visor clip 877LM Wireless Keyless Entry Enables homeowner to operate garage door garage door opener from outside by entering a password on a specially designed keyboard Also can add a temporary password for visitors or service persons This temporary password can be limited to a programmable number of hours or entries e e A 380LM Remote Light Enables homeowner to turn on a work light from their car with their garage door opener remote or from anywhere in their home with an additional LiftMaster Security remote 35 475LM Battery Backup Provides backup power to the garage door Opener 975LM Laser Park Assist Laser enables homeowners to precisely park vehicles in the garage 41A5281 Extension Brackets Optional For safety reversing sensor installation onto the wall or floor 480LM Alternate Mounting Kit This kit allows model 8500 to be mounted below the torsion bar in
34. essary to cut the rope heat seal the cut end with a match or lighter to prevent unraveling Garage Door Opener Emergency Release Cable Emergency Release Handle Overhand Knot 3 Install Power Door Lock The power door lock is used to prevent the garage door from being manually opened once the door is fully closed 1 The power door lock must be mounted within 10 feet 3 05 m of garage door Opener with approximately a 3 inch 7 6 cm distance between the center of a door roller and the hole for the power door lock bolt If possible mount on same side as garage door opener The second roller from the bottom is ideal for most installations Ensure rail Surface is clean and attach lock template to track Drill holes as marked on the template Fasten power door lock to the outside of the garage door track with hardware provided 10 feet 3 05 m max Run bell wire up wall to garage door opener Use insulated staples to secure wire in several places Insert wire through the bottom of the garage door opener Plug the connector into the garage door opener Garage Door Track 9 amp WARNING To prevent possible SERIOUS INJURY or DEATH from a falling garage door e f possible use emergency release handle to disengage door ONLY when garage door is CLOSED Weak or broken springs or unbalanced door could result in an open door falling rapidly and or unexpectedl
35. he track It should lie flush with the lip hugging the back edge of the track as shown If your door track will not support the bracket securely wall installation is recommended Door Track Safety Reversing Sensor Bracket ia OPTION B Wall Installation 1 Place the bracket against the wall with curved arms facing the door Be sure there is enough clearance for the sensor beam to be unobstructed 2 f additional depth is needed an extension bracket see Accessories or wood blocks can be used 3 Use bracket mounting holes as a template to locate and drill 2 3 16 diameter pilot holes on the wall at each side of the door no higher than 6 15 cm above the floor 4 Attach brackets to wall with lag screws not provided If using extension brackets or wood blocks adjust right and left assemblies to the same distance out from the mounting surface Make sure all door hardware obstructions are cleared Provided with Extension Bracket Sensor Bracket de Fasten Wood Block to Wall with Lag Screws not provided Safety Reversing Sensor Bracket Lag Screws not provided Extension Bracket See Accessories Provided with Extension Bracket Safety Reversing OPTION C Floor Installation 1 Use wood blocks or extension brackets see Accessories to elevate sensor brackets so the lenses will be no higher than 6 15 cm above the floor 2 Carefully me
36. ierce the wire with the staple as this may cause a short or an open circuit 10 Strip 7 16 11 mm of insulation from the end of the wire near the garage door opener Connect bell wire to the quick connect terminals on the garage door opener white to white and white red to red 11 Fasten the warning placard to the wall next to the door control NOTE DO NOT connect the power and operate the garage door opener at this time The door will travel to the full open position but will not return to the close position until the sensor beams are connected and properly aligned See page 13 a to garage door opener to door control ANA WARNING To prevent possible SERIOUS INJURY or DEATH from electrocution e Be sure power is NOT connected BEFORE installing door control e Connect ONLY to 7 28 VOLT low voltage wires To prevent possible SERIOUS INJURY or DEATH from a closing garage door nstall door control within sight of garage door out of reach of children at a minimum height of 5 feet 1 5 m and away from ALL moving parts of door e NEVER permit children to operate or play with door control push buttons or remote control transmitters Activate door ONLY when it can be seen clearly is properly adjusted and there are no obstructions to door travel ALWAYS keep garage door in sight until completely closed NEVER permit anyone to cross path of closing garage door
37. il the LED starts flashing slowly then release 2 Pushand hold the black button until the door reaches the desired UP open position NOTE Make sure the door opens high enough for your vehicle 3 Push the door control or programmed remote control This sets the UP open limit and begins closing the door 4 Immediately when the door begins to close press and release either the black or yellow button This will stop the door SETTING THE DOWN POSITION 5 Push and hold the yellow button until the door reaches the desired DOWN closed position 6 Once the door is closed if there appears to be too much pressure on the door you may toggle the door back and forth using the black and yellow buttons to reach the desired closed position 7 Push the door control or programmed remote control This sets the DOWN close limit and the door should open Proceed to Set the Force 4 amp WARNING Without a properly installed safety reversal system persons particularly small children could be SERIOUSLY INJURED or KILLED by a closing garage door NEVER learn forces or limits when door is binding or sticking Repair door first ncorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system e After ANY adjustments are made the safety reversal system MUST be tested Door MUST reverse on contact with
38. is necessary The invisible light beam path must be unobstructed No part of the garage door door tracks springs hinges rollers or other hardware may interrupt the beam while the door is closing uf o o A A A iv V V V d A A A iv V V V vj A A A V V V d SILLAS Safety Reversing Sensor Invisible Light Beam 6 15 cm max above floor X Protection Area Safety Reversing Sensor 6 15 cm max above floor Facing the door from inside the garage 4 amp WARNING Be sure power is NOT connected to the garage door opener BEFORE installing the safety reversing sensor To prevent SERIOUS INJURY or DEATH from a closing garage door Correctly connect and align the safety reversing sensor This required safety device MUST NOT be disabled nstall the safety reversing sensor so beam is NO HIGHER than 6 15 cm above garage floor Installation INSTALLING THE BRACKETS Be sure power to the opener is disconnected Install and align the brackets so the safety reversing sensors will face each other across the garage door with the beam no higher than 6 15 cm above the floor Choose one of the following installations OPTION A Track Installation 1 Slip the curved arms over the rounded edge of each door track with the curved arms facing the door Snap into place against the side of t
39. ited warranty will be repaired or replaced at Seller s sole option at no cost to you and returned pre paid Defective parts will be repaired or replaced with new or factory rebuilt parts at Seller s sole option You are responsible for any costs incurred in removing and or reinstalling the product or any component ALL IMPLIED WARRANTIES FOR THE PRODUCT INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE APPLICABLE LIMITED WARRANTY PERIOD SET FORTH ABOVE FOR THE RELATED COMPONENT S AND NO IMPLIED WARRANTIES WILL EXIST OR APPLY AFTER SUCH PERIOD Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you THIS LIMITED WARRANTY DOES NOT COVER NON DEFECT DAMAGE DAMAGE CAUSED BY IMPROPER INSTALLATION OPERATION OR CARE INCLUDING BUT NOT LIMITED TO ABUSE MISUSE FAILURE TO PROVIDE REASONABLE AND NECESSARY MAINTENANCE UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT LABOR CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT REPLACEMENT OF CONSUMABLE ITEMS E G BATTERIES IN REMOTE CONTROL TRANSMITTERS AND LIGHT BULBS OR UNITS INSTALLED FOR NON RESIDENTIAL USE THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH OR RELATING TO THE GARAGE DOOR OR GARAGE DOOR HARDWARE INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS DOOR ROLLERS DOOR ALIGNMENT OR HINGES THIS LIMITED WARRANTY ALSO DOES NOT C
40. late Assembly 1 Attach the Collar to the Garage Door Opener A WARNING s binis installation difficulties do not run the garage door garage door opener until instructed To preven t possible S ERO U s UU RY The garage door opener can be installed on either side of the door see PLANNING section tightened The door may NOT a y page 3 The illustrations shown are for installation on the left side correctly or limits may be lost due to 1 Loosen the collar screws collar slip 2 Attach collar to the garage door opener motor shaft The side of the collar with the larger hole should be placed on the motor shaft Ensure that the collar is seated all the way on motor shaft until stop is reached 3 Position the collar so the screws are facing out and are accessible when attached to the torsion bar 4 Tighten the screws on both sides of the collar equally to secure collar to the motor shaft to 12 14 ft lbs of torque NOTE Do not tighten set screws until indicated Collar Motor Shaft 3 16 Hex Key Wrench RIGHT WRONG Assembly HARDWARE 2 Attach Mounting Bracket to Garage Door Opener 1 Loosely attach slotted side of mounting bracket to the same side of the garage door opener as the collar using self threading screws provided NOTE Do not tighten screws until instructed Screw 10 32 2 Installation Socket
41. ng the Door Control MyQ Control Panel NOTE Due to power consumption this door control Model 888LM cannot be used in conjunction with another wired door control connected to your garage door opener If an additional door control is needed the wireless door control model 885LM can be programmed to the door control Model 888LM To program the 885LM to the MyQ Control Panel follow the remote control programming steps NOTE MyQ light controls will continue to work however all other MyQ devices and TTC will not work if using the Model 580LM Alternate Power Supply or when in Battery Backup mode Push Bar HOLD OPEN 1 Minute Button for the TTC LED Timer To Close TTC 5 Minute LIGHT Button TTC LED Motion Sensor 10 Minute TTC LED PUSH BAR Press the push bar to open close the door LOCK Designed to prevent operation of the door from hand held remote controls However the door will open and close from the Door Control the Outdoor Key Switch the Keyless Entry Accessories and MyQ Internet Gateway Activate Press and hold the LOCK button for 2 seconds The command LED will flash as long as the lock feature is activated and your handheld remote control will not operate your door at this time Deactivate Press and hold the LOCK button again for 2 seconds The command LED will stop flashing and normal operation will resume MOTION SENSOR This feature will automatically turn on the garage d
42. ontrol NOTE Use the learn button on the door control to program all accessories The yellow learn button on the garage door opener will NOT program accessories To Add a Remote Control Keyless Entry or MyQ Enabled Accessories using the Door Control MyQ Control Panel REMOTE CONTROL 1 Press the MyQ Control Panel LEARN KEYLESS ENTRY button twice the red learn LED will 1 Press the MyQ Control Panel LEARN button twice the red learn turnon LED will turn on 2 Press the button on the remote control j that you wish to operate your garage door The garage door opener lights will flash or two clicks will be heard when the code has been programmed 2 Enter a 4 digit personal identification number PIN of your choice on the keyless entry keypad Then press the ENTER button 3 The garage door opener lights will flash or two clicks will be heard when the code has been programmed Command LED yellow MyQ ENABLED ACCESSORIES 1 Press the MyQ Control Panel LEARN button twice the red learn LED will turn on 2 Press the LEARN button on the MyQ device Button Model 823LM Remote Light Switch Light module can be synchronized with Bu the garage door opener light bulbs utton Model 825LM Remote Light Control Model 829LM Garage Door and Gate Monitor MyQ viuda may be programmed to the inoj LiftMaster Internet Gateway Model 828LM Light module can be synchroniz
43. ood blocks may be needed to install safety reversing sensors Alternate floor mounting of the safety reversing sensors will require hardware not provided Any gap between the floor and the bottom of the door must not exceed 1 4 inch 6 mm otherwise the safety reversal system may not work properly A model 475LM Battery Backup is strongly recommended if there is no access door to the garage as this garage door opener cannot be used in conjunction with an external emergency release mechanism VZIT N N N C 8 inches 20 3 cm e S Safety reversing DIC sensor c _ 3 inches 7 6 cm and down or left and right If the movement is not corrected the life of the garage door opener will be greatly reduced ht Introduction Preparing Your Garage Door BEFORE YOU BEGIN e Disable locks e Remove any ropes connected to the garage door Complete the following test to make sure the garage door is balanced and is not sticking or binding 1 Lift the door halfway up Release the door If balanced it should stay in place supported entirely by its springs 2 Raise and lower the door to check for binding or sticking If your door binds sticks or is out of balance call a trained door systems technician 3 Verify equal cable tension on each side of do
44. oor opener lights when motion is sensed The lights will come on for 4 1 2 minutes then shut off Activate Deactivate Slide the motion sensor switch ON or OFF TIMER TO CLOSE TTC The TTC feature automatically closes the door after a specified time period 1 5 or 10 minutes Once the TTC has been set and the door is open the LED for the selected close interval will blink and begin to count down to close the door The control panel will beep and the garage door opener lights will flash before closing the door The TTC feature will deactivate if the garage door encounters an obstruction twice or the safety reversing sensors are incorrectly installed The garage door will reverse open and WILL NOT close until the obstructions are clear or the safety reversing sensors are correctly installed When the obstruction has been cleared or the safety reversing sensors have been aligned the door will close when the garage door opener is activated Activate Press and hold the ON button until one of the TTC LEDs light up Then press the ON button again to cycle through the time interval options the corresponding TTC LED will light for each time interval The garage door opener light bulbs will blink as confirmation Deactivate Press and hold the OFF button until all TTC LEDs turn off and a beep is heard from the control panel To suspend the TTC To suspend the TTC and temporarily hold the door open press and release the HOLD OPEN
45. or Cable tension should remain equal during the entire travel of the door Sectional Door Tools Needed 4 amp WARNING To prevent possible SERIOUS INJURY or DEATH e ALWAYS call a trained door systems technician if garage door binds sticks or is out of balance An unbalanced garage door may NOT reverse when required e NEVER try to loosen move or adjust garage door door springs cables pulleys brackets or their hardware ALL of which are under EXTREME tension Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing and operating garage door opener to avoid entanglement CAUTION To prevent damage to garage door and opener e ALWAYS disable locks BEFORE installing and operating the opener e ONLY operate garage door opener at 120 V 60 Hz to avoid malfunction and damage DO NOT exceed 10 complete cycles of door operation per hour During assembly installation and adjustment of the garage door opener instructions will call for hand tools as illustrated below Stepladder Suum 5 32 3 16 SORS and 3 4 Drill Bits CD Os 1 4 5 16 amp 3 8 Sockets J and Wrench with 6 Extension Specifications MOUS cs ccs dentata ni ant nei eee Ma Meath 120 Vac 60 Hz ONLY CUTE s ciu Dee Sarat Sete ee moan Gade ate d ce ew RR didn 1 0 AMP Rated Loader dressi eran er Moga REETLEXG RR i epr ere 325 in Ib se
46. or MUST reverse on contact with a 1 1 2 3 8 cm high object or a 2x4 laid flat on the floor Installation 1 Position and Mount the Garage Door Opener NOTE For additional mounting options refer to the accessories page 1 2 Close the garage door completely Slide the garage door opener onto the end of the torsion bar If the torsion bar is too long or damaged you may need to cut the torsion bar Ensure the collar does not touch the bearing plate Use a level to position and vertically align the garage door opener Verify the mounting bracket is located on a solid surface such as wood concrete or door flag bracket When the garage door opener is properly aligned mark the mounting bracket holes If necessary tighten collar screws on the torsion bar to hold garage door opener in place while marking holes NOTE The garage door opener does not have to be flush to wall Remove the garage door opener from torsion bar Drill 3 16 inch pilot holes at the marked locations Drill through steel plate if necessary Slide the garage door opener back onto the torsion bar until pilot holes align with bracket Securely tighten collar screws to the torsion bar to 12 14 ft lbs of torque Figure 1 Securely tighten both set screws Figure 1 NOTE You may need to manually raise the door slightly in order to reach the set screws Secure the mounting bracket to the wall and to the garage door opener Use the 14 10x1 7 8 inch
47. ore the garage door opener will move in the down direction The garage door opener lights will turn on when the garage door opener is activated They will turn off automatically after 4 1 2 minutes or provide constant light when the Light feature on the MyQ Control Panel is activated Bulb size is A19 Bulb power is 100 watts maximum Light feature Lights will also turn on when someone walks through the open garage door With a MyQ Control Panel this feature may be turned off as follows With the garage door opener lights off press and hold the light button for 10 seconds until 23 the light goes on then off again To restore this feature start with the garage door opener lights on then press and hold the light button for 10 seconds until the light goes off then on again TIMER TO CLOSE TTC The TTC feature automatically closes the door after a specified time period that can be adjusted using a TTC enabled door control Prior to and during the door closing the garage door opener lights will flash and the garage door opener will beep BATTERY BACKUP The battery backup system allows access in and out of your garage even when the power is out When the garage door opener is operating on battery power the garage door opener will run slower the light will not function the Battery Status LED will glow solid orange and a beep will sound approximately every 2 seconds f applicable Operation Usi
48. ove the two screws and open the case 3V2016 2 i 29 4 amp WARNING To prevent possible SERIOUS INJURY or DEATH e NEVER allow small children near batteries f battery is swallowed immediately notify doctor To reduce risk of fire explosion or chemical burn Replace ONLY with 3V2016 coin batteries DO NOT recharge disassemble heat above 212 F 100 C or incinerate NOTICE To comply with FCC and or Industry Canada IC rules adjustment or modifications of this receiver and or transmitter are prohibited except for changing the code setting or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS Tested to Comply with FCC Standards FOR HOME OR OFFICE USE Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Troubleshooting Diagnostic Chart Your garage door opener is programmed with self diagnostic capabilities The diagnostic LED will flash a number of times then pause signifying it has found a potential issue Consult Diagnostic Chart below Garage Door Opener Op a l 3 E Diagnostic LED N ne 9 eL ET p oo eee pee
49. rage door is closed 2 Pull the emergency release handle The garage door should then be able to be opened manually 3 Return the door to the closed position 4 Pull the emergency handle a second time 5 Reconnect the door to the garage door opener 4 amp WARNING To prevent possible SERIOUS INJURY or DEATH from a falling garage door f possible use emergency release handle to disengage door ONLY when garage door is CLOSED Weak or broken springs or unbalanced door could result in an open door falling rapidly and or unexpectedly NEVER use emergency release handle unless garage doorway is clear of persons and obstructions Power Door Lock Manual Release Emergency Release Handle 22 Operation IMPORTANT SAFETY INSTRUCTIONS A amp WARNING To reduce the risk of SEVERE INJURY or DEATH READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS ALWAYS keep remote controls out of reach of children NEVER permit children to operate or play with door control push buttons or remote controls ONLY activate door when it can be seen clearly it is properly adjusted and there are no obstructions to door travel ALWAYS keep garage door in sight and away from people and objects until completely closed NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR NO ONE SHOULD GO UNDER A STOPPED PARTIALLY OPENED DOOR If possible use emergency release handle
50. tall the Battery Backup optional When in Battery Backup mode wireless MyQ devices and Timer To Close will be disabled If the optional Battery Backup is part of this installation it should be installed at this time The Battery Backup can be mounted to either the ceiling or a wall within 3 feet 9 m of the garage door opener 1 2 3 Unplug the garage door opener Position the Battery Backup on a structural support ceiling joist or wall stud Attach the Battery Backup to the support with the 1 1 2 inch lag screws 2 provided There are mounting holes on either side of the Battery Backup Connect the Battery Backup cord into the connector on the bottom of the garage door opener Follow all instructions included with the Battery Backup to test for proper operation 475LM Battery Backup Connector Battery Backup Cord Adjustment 1 Program the Travel Limits Travel limits regulate the points at which the door will stop when moving up or down Adjust the position of the door by using the black and yellow buttons Black moves the door UP open and yellow moves the door DOWN close NOTE The yellow command LED and the red learn LED will blink quickly for up to 5 minutes as the control panel recharges When the control panel is operational the yellow command LED will glow steadily SETTING THE UP POSITION 1 Press and hold the black button unt
51. tallation hardware bag eyes with 2 conductor bell wire attached includes hardware listed on page 5 114A4565 Owner s manual 114A4565SP Owner s manual Spanish 33 Repair Parts Garage Door Opener Assembly Parts KEY PART KEY PART NO NO DESCRIPTION NO NO DESCRIPTION 1 041DJ002 Logic board complete with plate 4 41A6095 Motor with bracket 2 41A6408 Travel Module 5 418122 Power cord 3 410168 Transformer 6 41A6348 3 Cover 34 Accessories MAX ACCESSORIES Compatible with LiftMaster garage door openers manufactured since 1993 877MAX MAX Wireless Keyless Entry For use outside of the home to enable access to the garage using a 4 digit PIN 890MAX Mini 3 Button MAX Remote Control 893MAX 3 Button MAX Remote Control Includes visor clip 895MAX MyQ ACCESSORIES 823LM Remote Light Switch Automatically control your lights using your garage door opener a SECURITY 2 0 remote control or a LiftMaster Internet Gateway Simply replaces your current wired wall switch 828LM Internet enabled LiftMaster Internet Gateway accessory which connects to the computer and allows you to monitor and control garage door openers and lighting accessories enabled by MyQ technology Garage and Gate Monitor Monitor open closed status for up to 4 MyQ compatible garage door openers or gate operators and close them from anywh
52. the case where the torsion bar is not round or the normal mounting area is obstructed 580LM Alternate Power System Model 580LM Alternate Power Supply may be installed if an outlet is not located near the garage door opener 990LM Surge Protector The Garage Door Opener Surge Protector is designed to protect LiftMaster garage door openers against damage from lightning and power surges Easy to install Repair Parts and Service LIFTMASTER SERVICE IS ON HOW TO ORDER CALL REPAIR PARTS OUR LARGE SERVICE ORGANIZATION Selling prices will be furnished on request or parts will be shipped at SPANS AMERICA prevailing prices and you will be billed accordingly WHEN ORDERING REPAIR PARTS ALWAYS GIVE THE FOLLOWING INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR INFORMATION TELEPHONE e PART NUMBER SIMPLY DIAL OUR TOLL FREE NUMBER PART NAME 1 800 528 9131 MODEL NUMBER ADDRESS ORDERS TO THE CHAMBERLAIN GROUP INC Technical Support Group 6050 S Country Club Road Tucson Arizona 85706 www liftmaster com For professional installation parts and service contact your local SERVICE INFORMATION LIFTMASTER CHAMBERLAIN dealer Look for him in the Yellow TOLL FREE NUMBER Pages or call our Service number for a list of dealers in your area 1 800 528 9131 Warranty LIFTMASTER FIVE YEAR LIMITED WARRANTY LIFETIME MOTOR LIMITED WARRANTY ONE YEAR LIMITED WARRANTY FOR THE BATTERY
53. the garage door e Verify the lock feature is not activated on the door control e Reprogram the remote control e fthe remote control will still not activate the door check the diagnostic codes to ensure the garage door opener is working properly The remote control has short range e Change the location of the remote control in your car e Check to be sure the antenna on the side or back panel of the garage door opener extends fully downward e Some installations may have shorter range due to a metal door foil backed insulation or metal garage siding The door doesn t open completely e Check power door lock e ls something obstructing the door Is it out of balance or are the springs broken Remove the obstruction or repair the door The door opens but won t close e Check cable tension monitor see Installation Step 4 e ifthe garage door opener lights blink check the safety reversing sensor see Installation Step 9 e ifthe garage door opener lights don t blink and it is a new installation see Adjustment Step 2 For an existing installation see below Repeat the safety reverse test after the adjustment is complete 31 Troubleshooting Troubleshooting Continued The door reverses for no apparent reason and garage door opener lights don t blink e Check cable tension monitor see Installation Step 4 e s something obstructing the door Pull the emergency release handle Operate the door manually If it is un
54. to disengage door ONLY when door is CLOSED Use caution when using this release with the door open Weak or broken springs or unbalanced door could result in an open door falling rapidly and or unexpectedly and increasing the risk of SEVERE INJURY or DEATH NEVER use emergency release handle unless doorway is clear of persons and obstructions After ANY adjustments are made the safety reversal system MUST be tested Failure to adjust the garage door opener 9 Safety reversal system MUST be tested every month Door MUST reverse on contact with 1 1 2 3 8 cm high object or a 2x4 laid flat on the floor Failure to adjust the garage door opener properly may cause SEVERE INJURY or DEATH 10 ALWAYS KEEP DOOR PROPERLY BALANCED see page 4 An improperly balanced door may NOT reverse when required and could result in SEVERE INJURY or DEATH 11 ALL repairs to cables spring assemblies and other hardware ALL of which are under EXTREME tension MUST be made by a trained door systems technician 12 To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution disconnect ALL electric and battery power BEFORE performing ANY service or maintenance 13 This operator system is equipped with an unattended operation feature The door could move unexpectedly NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR 14 SAVE THESE INSTRUCTIONS properly may cause SEVERE INJURY or DEATH Using Your Garage Door Opener Your garage door open
55. wer Supply If you would like to use these features contact an electrician to install an outlet near to the garage door opener CONNECTION If permanent wiring is required by your local cote refer to the following procedure To make a permanent connection through the 7 8 inch hole in the back of the garage door opener according to local code 1 Be sure power is NOT connected to the opener and disconnect power to circuit Remove the garage door opener from the torsion bar remove cover screws and set the cover aside Remove the attached green ground terminal Cut black and white wires and strip away 1 2 inch 1 3 cm of insulation 3 inch 7 6 cm before spade terminals Remove the power cord from the garage door opener Install a 90 conduit or flex cable adapter to the 7 8 inch hole Reinstall garage door opener to torsion bar Run wires through conduit cut to proper length and strip insulation Attach with wire nuts provided Properly secure wire under plastic ties so that wire does not come in contact with moving parts 10 Reinstall the cover Black Wire White Wire 90 Connector Flexible Conduit Ground Tab Green Ground Screw Ground Wire Black Wire From Power Cord White Wire From Power Cord Installation ENSURE THE SAFETY REVERSING SENSORS ARE ALIGNED The door will not close if the sensors have not been installed and aligned
56. wire to garage door opener Use insulated staples to secure wire Connect bell wire to the green quick connect terminals on the garage door opener polarity is not important NOTE Cable must have tension through entire door travel Make sure there is no slack in cable on opposite side of garage door during normal operation If slack occurs during door travel adjust cables as required to garage door opener 777 m Drum OVO Qo To insert or release wire push in tab with screwdriver tip mni Cable HT GRN d G E O Oo Cable Tension Monitor Monitor Roller 1 8 1 4 3 6 mm L 4 to cable tension monitor 10 Cable Tension The cable tension monitor MUST be connected and properly installed before the garage door opener will move in the down direction The cable tension monitor detects ANY slack that may occur in the cables and will reverse the door eliminating service calls HARDWARE 8 Hex Head Screw 2 dinnnnnnnm Insulated Staples Not shown Screw 6 2 v Wall Anchor 2 SIDE VIEW ble Tension Monitor Roller 3 4 Min 19 mm Min VIILILLLLLLILLLLILILLILLLILILILLLLLLLTLILLLILLLLL LL A Installation 5 Install the Door Control MyQ Control Panel Install the door control within sight of the door at a minimum h
57. y e NEVER use emergency release handle unless garage doorway is clear of persons and obstructions HARDWARE Um HARDWARE jm Handle Lock Screws 1 4 20x1 2 2 Insulated Staples Not shown Lock Template Installation 4 Attach the Cable Tension Monitor Required NOTE The cable tension monitor is shipped for left side installation It is recommended that the cable tension monitor be installed on the same side of the door as the garage door opener For right side installation remove the snap ring holding the roller in place and reassemble it on the opposite side of the cable tension monitor 1 Position the cable tension monitor as close to the drum as possible Make sure cable tension monitor is located over a wood support member and the roller is free from any obstructions NOTE There must be no obstructions in the installation area that prevent the cable tension monitor or the cable itself from closing completely when slack is detected 2 Mark and drill 3 16 inch pilot holes for screws pilot holes are not required for anchors NOTE If the cable tension monitor cannot be mounted into wood with the lag screws provided it can be mounted into 1 2 inch or greater drywall using the wall anchors 2 and the 8 hex screws 2 provided in the hardware bag 3 Attach the cable tension monitor to the wall using the hardware provided Make sure that the roller is on top of the cable 4 Run bell

Manual - Assurance Overhead Doors of Tulsa

Contents

Download Pdf Manuals

Related Search

Related Contents