user manual
Contents
1. GND GND GND The module configuration blank sample for this diagram you will find after installing configuration program SERA located in the directory ConfigTemplates File name GTAUTO_v4_VehicleAlarm tcfg The connection diagram of the module is in parallel with already available security system Automated GSM security and control system www topkodas It 28 JeusIS oogun enu eustg Joo enuy onal nal nal nal age Sensor Si nal Capote Sensor Si Door Sensor Si Shock Sensor Si Lu Siren Si O MHS JOOP I Ul YMS T i VS ASNA uonius suJ yooquN guy Vo DINO Vo Deno V oC T EMO Vo Drino NOIN Temperature sensor MICROPHONE CTT 21S WAS S AZI _PUNnOID JOSU S SAPMOIOTIY gino JOSUO j Josu s YOOYS Jno 109099 S Siren O oo yams uow edw 2262 2nrT O o yams puuoq SUJ GND GND GND GND L V N AYN LIVE AVO N 12V oo uous JOOIUNS SMOPUIAA 25019 OML 0 IMO Ignitio 12V Ignition 40A Out2_SMS_control 10u09 SIS EMO me Black White 12V ONUOS SINS FINO In the saloon of the vehicle the module should be placed in hard to reach place The device should be mounted in a place protected from impact of humidity or other materials causing corrosion as far as possible from heating elements of passeng2. User telephone number end symbol user ID number from 001 to 400 dial action 0 offor 1 on sequence OUT1 OUT2 OUT3 O0OUT4 ARM DISARM MIC Delete selected user s telephone number according to ID number User ID from 001 to 61 none 001 400 162 none 1 Delete all telephone numbers of remote control users from 001 to 400 Overheating temperature value upon reaching which the following SMS message will be 70 30 0 35 5 l 9 sent High temperature alarm Automated GSM security and control system www topkodas lt 20 Freezing temperature value upon reaching which the following SMS message will be 71 2 00 10 3 S sent Low temperature alarm 26 0 21 lt Temperature value for freezing equipment control 20 0 21 4 Temperature value for heating equipment control Send via SMS a part of information regarding configurations of the module 05 12 command code parameters will be sent 21 28 command code parameters will be sent 31 38 command code parameters will be sent none 1 40 49 command code parameters will be sent to make a request about output states Out 1 Out 4 test request System state request input output states will be sent along with current state of the system ARM DISARM ll m 123456 65432 To change installer s INST code recommended to change before applying the module in operation 123456 948921 To change user s USER code recommended before applying the mod
3. system state DISARM 123 59 y S236 ape System voltage Switch on testing Switch off testing Temperature 24 7 ce 92 20 AD Coba is closed a COMMS is opened COPS Connected GTAUTO v4 1106015 Ez 18 Software updating Updating of firmware version should be performed via PC The following is necessary e mini USB configuration cable e configuration software SERA e the new software version which may downloaded at www topkodas It More about software updating process see user manual of the software SERA Automated GSM security and control system www topkodas lt 30 12V 4 Annexes 1 Annex Central alarm system o 0 FUSE to vacuum central lock Automated GSM security and control system Lock www topkodas It GTauto Annex Z 9S WHV B Rd08i68Rd 96R8Rd0R8Ad48 hA Rd6 Rd R8A68hd 6 RB ALANAS E ALAN Rd68Ad 46R40 8 Rd6 R hd6RAd8 RAR Rd6 Rd RA68 ALAR 8 RB PTM RTE PTS RPT RT EP TER PTS EP TU ETC RP TURP TURP TEP FRCP TCR PTC PTE RP TURP TUPPER PPS R RPT Rn PTR PTM R mm e mB a s PT dann nam 9S ND YS 10 HE DER EORRROU RB RAR REPRE BOR RB BAH RRR RB RB R RRR BRAR RKR RB H EE TM BTR PTR RB PW RT PTR PTS RB PTM ETE RP TURP TUCO TEP Te RPT RE SLUU OUL lt 9S WHV ELSE AhLANALANAJEALANALANAJLAAL SLUUO 0 L lt 8 PTM RPT RBYT9 RPP Swe sere eee mmm mmm mem m mmm m m eee eee m R m m mm ee ee mm m mm m Bd08hd6R8Ad 8R
4. OUT4 you can program which to activate or deactivate the heating cooling system so to keep the temperature required This is the way to keep room temperature required Temperature range is 40 to 80 degrees Celsius or accordingly Fahrenheit It is possible to set a low temperature alarm and a high temperature alarm Passage through these thresholds will trigger alarm SMSs You can choose a temperature hysteresis If the temperature is too low or too high the Module will send SMS message including warning and actual temperature value allowing you to take action or a output to be activated to correct the temperature For example a user can receive a reporting SMS and also switch output on or off to achieve the requested temperate This is quite powerful temperature control system not only for residential use but for professional use only If your company sells heating on a calories basis this solution can help you a lot avoiding energy waste and useless trips to a location If you have a house in the mountains and want to make sure temperature is kept correctly GTauto is a professional solution to implement this decision Module can be used to monitor industrial refrigerators electrical transformers animal farms or any location or machine where temperature control is significant Temperature controller configuration window Temperature Controller Settings odling Settings T B 250 sr High Temp Alarm SMS Alarm High Temperature a
5. Cooling Hysteresis UF RE High Temp Cooler Hysteresis Cooler Output OUT lt Cooler OFF High Temp Alarm 300 L Lif High Temperature Alarm SMS Text High Temp Alarm Enable ee Hester OFF eating Settings Low Temp Low Temperature foo ne oe Low Temp Alarm SMS Hanm Low Temperature OF sC OUT Low Temp Alarm 2 D T Low Temperature Alarm SMS Text Low Temp Alarm Enable Temperature sensor is connected to the system wire contacts 9 Temp and 19 Temp Alarm and restore temperature may be changed Upon temperature alarm the module will send SMS message to a user And if setting exist the module will switch the selected output It is comfortable to use this function for indoor heating management In a case of accuracy shortage temperature sensor may be calibrated additionally Following the equation Temperature X ADC Y and by selecting X and Y coefficients Temperature calibration may be performed in software SERA in testing window It is necessary to have accurate thermometer in order to measure temperature at least in two points In testing window to read temperature ADC indications in these points Following the equation Temperature X ADC Y to calculate X and Y coefficients Calculated X and Y coefficients should be programmed in the module It is easy to calculate X and Y coefficients in MC Excel by using trendline y 0 3284x 269 26 Heating Hysteresis Temperature Sensor Calibration 0 3466
6. INT INS modes 0 delay 1 interior 2 instant 3 24h 4 silent 5 fire 11111121 02111133 11111221 02111111 Input IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 types 0 NO type 1 NC type 2 EOL 1111 0011 Service messages Arm Disarm Reset Test 1 ON 0 OFF In the example service messages Reset and Test will be sent aA S re In th example inputs INI IN3 INS ING INE INO will be restored LT CORR IN1 input name changing up to 16 symbols the end symbol Alarm Bonnet IN2 input name changing up to 16 symbols the end symbol Alarm Door IN3 input name changing up to 16 symbols the end symbol Microwave Pare Alarm Microwave IN4 input name changing up to 16 symbols the end symbol Ignition On INS input name changing up to 16 symbols the end symbol IN6 input name changing up to 16 symbols the end symbol Low Battery IN7 input name changing up to 16 symbols the end symbol IN1 input restore name changing up to 16 symbols the end symbol IN2 input restore name changing up to 16 symbols the end symbol IN3 input restore name changing up to 16 symbols the end symbol INS input restore name changing up to 16 symbols the end symbol IN6 input restore name changing up to 16 symbols the end symbol IN7 input restore name changing up to 16 symbols the end symbol a ells Outl output activation text changing up to 16 symbols the end
7. Microphone and voice r T 16 Le Ponne ON e E E 17 l2 Fo ivalbutoumut diarias ession aia n a ESERE 17 12 2 AOUIPULCONMECIION CIA CLANS cessisse ani i n aa aE EA RE i aa aii 17 12 3 Opetationaloutp t parameters ssdesceveciexcsescessceaudcesstevedeesatecvereacpseezceasddeeeteavad nade raai aad aiai ana iiri 17 IE Timers ihe security Syste scssusrioian ie ani i i aaa E ES e a inda a a ECan 17 14 Automatic periodical test sScending sees eee eee eee 18 l3 Messages e Te TT 18 16 Remote control of the module via SMS messages or via Short call 18 I7 Preparation tOo Operate amnesia ee mere er a ere re Smee A SOT a eee eee eee eee ee 18 DM I Ca aos csc ce seca E nea once cae net tronic oe nea amc E nace Cott see nee ude tee ace es Gud I P cea naebnes 19 17 2 Configuration and control of GSM communication module via SMS messages esse 19 I gt Conhsuration Of the module vid PC sser eE EERE EE O 26 17 4 Installation of the product and connection d1I99granm sss sese 26 17 5 Installation instruction and connection diagram of security system for house mini mobile cottages boats 26 17 6 Vehicle s GSM messages system Installation manual and connection diagram sss sees 27 FEl MSM a ls 1 OS e ote ec tense sree as E ec agai we ea oe eterna ce arise ate eu enas onsierednes eatenoe secede 30 LS OR AS WN Ce T TH 30 POUNCE S cee ayers E EEA pace ce taaiade tee ayaa tect ee E atest EE I AE E EN ae aeeu E AE T 31 Me RUT eh pan estes Steen an etc naeme tt
8. SMS message centre number using GSM phones Mostly SIM card already has SMS centre number inserted please skip this step Remove PIN code request of the SIM card it can be done using GSM phone Install SERA configuration program Connect USB cable to the PC and to the module Launch SERA program Guidelines on how to use SERA program is available in SERA description GSM communication strength IMEI and SMS centre number are available in Test window see SERA description e Configure telephone numbers to which information should be transferred Automated GSM security and control system www topkodas lt 18 e Set the numbers to send SMS and to make a call e Set active inputs which will be used For example if the input will not be used it should be disabled e Set periodicity of communication test if OO is entered the test will not be send e Set input parameters e Set output OUT1 OUT2 OUT3 OUTS states if applied After inserting SIM card or upon changing parameters of the module it is necessary to press RESET button There are two types to configure the module The first via SMS messages The second via PC by connecting the module to PC via programming cable Full change of parameters is possible only via PC by connecting programming cable If possible we recommend to configure the module via PC 17 1 SIM card GTAUTO module is not locked with a particular GSM network This means that a user may use SIM card of
9. and Unlock see clause 0 3 Each input may be linked with selected output i e to switch selected output depending on output state This feature enables to apply the module for premisses automation and temperature control For example For example Automated GSM security and control system www topkodas lt 14 if temperature drops below the standard limit the module is able to automatically activate heating system and also to inform a user about critical temperature by sending him an SMS 11 1 Equivalent input diagrams Equivalent 1 4 input diagram V GTALARM 4 2 2K e e IN1 IN4 5 6 inputs are used when Pull Up resistor is not necessary for the input For example when signal should be taken from vehicle s bell or ignition or from other device for which extraneous signal cannot be applied These inputs do not have internal Pull Up resistor Input resistance is 22kOhm Equivalent diagram of 5 6 inputs GTALARM 11 2 Sensor connection diagrams Sensors may be connected following 4 different connection diagrams e NC normally closed contact e NO normally open contact e NC EOL normally closed with end of line resistor line resistor e NO EOL normally closed with end of line resistor resistor NOTE All resistors should be 1 kOm 10 The length of wires for connection of sensors can not exceed 300m and resistance of wire connected to sensor c
10. changed 1 e if output has been deactivated it is activated and vice versa 51 52 53 54 commands sets preferred output state if O is being sent the output is being deactivated if 1 the output is being activated 50 and 51 52 53 54 commands performs the same action i e changes output states The user may use command which are the more convenient for him 58 command changes the state of selected output for set time limit If you wish to change invert OUT1 OUT4 states and to receive information about output states the following message should be sent USER 123456 50 1 50 3 80 5 USER user type 123456 user code space character 50 to change state of selected output space character 1 to change state of first output OUT 1 space character 50 to change state of selected output space character 3 to change state of first output OUT 1 space character 80 command see table space character 5 to send output states This command is not necessary Automated GSM security and control system www topkodas lt 23 If you wish to activate OUT1 and to deactivate OUT2 USER 123456 51 1 57 0 90 3 USER user type 123456 user code space character 51 set OUT state space character 1 deactivated output space character 52 set OUT2 state space character U deactivated output space character 80 command see table space character 5 to send output states This
11. command is not necessary Output control by selecting trigerring time interval USER123456 58 1 48 USER 123456 58 2 5 USER user type 123456 user code space character 58 command see table space character automatically e enable OUT for 48 seconds enable OUT2 for 5 seconds 1 enable OUT1 output 1 OUT1 2 OUT2 3 OUT3 4 OUT4 ARM DISARM of the security system via SMS message USER123456 59 0 USER123456_59_1 DISARM the security system ARM the security system 48 Output triggering time limit set for 48 seconds After time limit of 48 seconds OUT1 will be disabled It is possible to download test of the module control message according to request command USER 123456 80 6 USER user type 123456 user code space character space character e 6 text query Upon sending command SMS USER123456 80 6 test message will be 80 information request command see table 17 1 sent to the number from which SMS message has been sent Below see the example of received test SMS message Clarifications Signal strength Numerical values of communication signal level Corresponds the following meanings according GSM telephone 0 very weak signal communication loss limit 1 5 very weak signal correspond to one bar on the monitor of a mobile phone Automated GSM security and control system www topkodas It Test Signal strength 17 Syste
12. heater control options O O O O In order to control big power alternating current equipment it is comfortable to use solid state relays Standard AC DC adapter with the voltage 1OV 14V and current gt 1A might be used to powering the module dey Attention AC equipment can not be connected directly to the module It is necessary to use a special relays or other methods which are in compliance with electrical safety requirements Attention When controlling devices from the AC network it is necessary to follow all electrical safety requirements Module connection scheme to control heating or cooling equipment Furnance Heater Cooling Device Air Conditioner p iia aaa N i k OO p b i j efl eL LES EHE L 3 22 ST STE ake 5 5 2 eI fee S a g 2 0 ojo wn S nanm j EEN i a HANYOUNG a L gt HANYOUNG oo Bar AAR Solid State Relay AC 85 260V l DC 10 14V gt 1A DC 85 260V 5 24V Input 5 24V Input GND 12V O GND THT e Heater Control OUT2 FUSE 5A d 12V Automated GSM security and control system www topkodas It gt 1A AC DC adapter 10 14V 1 9 2 Remote temperature control via SMS messages Temperature may be changed in remote manner by using SMS commands Overheating temperature value upon reaching which the following SMS message will be sent High temperature alarm INST 123456 70_35 5 INST u
13. of parameters of the module USER User commands This verifier is used for module control Installer s or user s password space character Command code space character Configuration array One SMS message may include as many commands as one SMS message may cover i e 160 symbols including spaces In such case firstly verifier should be sent password should be written without space after the verifier and further come command code parameter command code parameters etc separated with space lt The module executes the commands as follows the first command next after the password and further go all other commands from the left to the right Automated GSM security and control system www topkodas lt 19 Beginning INST Password Slo Command code 123456 17 1 Table of Installer s command codes Command Examples of command parameters default parameters Clarifications settings examples Telephone number of users to whom send SMS and to whom make a call DIAL up to none TelNo 01 16 symbols the end symbol after the symbol user priority number 01 16 should be entered ane po ete selected user s telephone number according to priority number User ID from 01 to ee ooo Several Lock Unlock modes are available 0 1 2 3 4 5 6 see a in the annex No3 BS P In the example test to users will be send each hour o7 tf LED indication Test Reg l on 0 of S Input INLINZIN3 IN4IN5IN6
14. of which is connected to car body The system should be installed in a saloon of vehicle following installation manual of the manufacturer The module may be installed in line with already available security system such as GSM SMS pager or as independent separate system for car protection Connection diagram of the module as independent protection system is see below Automated GSM security and control system www topkodas It 27 i PT N T E E T bie bcs EET Aa L SA 5 L Sa tS A Pe CT N ed PH ed C ed r IS a ae 5 SF eee ee a ee 2A p w ta ahead MICROPHONE L MICN MICP Temp _Temp Led A Led K Out4 1 5 A Out3C1 5 A Out2 1 5 A Uu TS A _In8_Unlock In7_Lock __ In6_Siren ELE ER EKELELEKEFEREL EH REESE So 0 RIE 2 2 D f D 3 LElel a E Nl e lt el S S16 e v Q 3 l 2 E 2 StS 9 Gl Black BILE IS IZ IEIZ SIM Gle Ol ole mmelala le m S GND AV 2 N Car Battery gt K L Black White Temperature sensor aum amp dad ed o d Turn Lamps V t 12V ee ees 12V S yy 3 p 2 5 i ZS 2 S Sl amp i ba G Ignition Cut 40A 12V E SO Q S Q GND Out remote control Ignition L E o gt a 0 D ay T e eG OB Signal to auto close i Z L 5 Windows Sunroof and Side E A GND 12V Turn Lamps Mirrors upon locking N To CAR central LocK Siren and Unlock signals
15. type installer 123456 installer s code space character 05 command see table space character 1 lock unlock modes of the module see diagrams in the see diagrams in the 2 annex 17 2Table of users codes z Command Beginni arameters Possible oa 8 Password P Clarifications ng default commands pon 1 OUT1 2 OUT2 3 OUT3 4 OUT4 Change state of selected 29 OUT output Output state changes every time after sending command code Explanation see below the table USER 123456 ARM DISARM command 0 DISARM the security ear l ane U or 1 ARM the security system Send via SMS a part of information regarding configurations of the module 01 12 command code parameters will be sent 21 28 command code parameters will be sent 31 38 command code parameters will be sent cans EE So 40 49 command code parameters will be sent to make a request about output states Out 1 Out 4 test request System state request will send information on input output states and system state ARM DISARM Outputs control via SMS messages Output states of the module may also be controlled via SMS messages Let s assume that vehicle ignition should be blocked thus the first output should be connected to ignition blocking relay For outputs control the following commands are used 50 51 52 53 54 58 Command 50 changes inverts state of selected output When this command is being sent output state is being
16. v 274 5 vr Equation Temperatures A 400 Teperature Temperature may be measured in Celsius and Fahrenheit Automated GSM security and control system www topkodas lt 10 9 1 Premisses automation temperature controller installation and connection diagram Preparation of the module for operation by using configuration software pictures and the more detailed info are available in SERA description Define parameters of the outputs Output state SMS text output operation description OUT definition CTRL SMS DIAL state type State mode Steady If necessary output operation might be inverted In the GSM communication window parameters of the users to send SMS and DIAL should be set Also check boxes should be checked to send SMS and DIAL to a user about temperature alarms In GSM remote control window telephone numbers of users who will be able to control selected outputs via free short call should be entered On The Temperature Controller Settings window set the cooler device temperature control settings o Cooling temperature value High temperature Cooling hysteresis Select cooler control output OUT1 OUTA4 or disable if cooler device is not used Determine the temperature value at which will be sent an SMS overheat temperature alarm Determine the temperature at which the value will be sent an SMS temperature alarm o Ifyou want to receive overheat alarm need to check box Enable Similar settings are done with
17. 468 R N 4907 BOHHRH OB BR HGH HE DEBE Nt PTUEPTUEPTEPTUE PF N y0 UN A AE N 4907 won e Kee Nt gl NPON JO SEIS 32 www topkodas lt Automated GSM security and control system
18. 8 2 Users to receive SMS DIAL messages eee eee 9 8 3 Remote control Users who are able to control the module via short call 9 9 Temperature control and maintenance Heating and cooling System control sss sese 10 9 1 Premisses automation temperature controller installation and connection diagram sss sese 11 9 2 Remote temperature control via SMS messages see 12 TO BRIVIS AIR NOT me modi ereen EAA a 12 We ARWDISARM vias horr CA einne n A A A a 12 10 2 ARM DISARM by sending SMS message sss eee 12 10 3 ARM DISARM by using Lock and Unlock inputs sss sese sese 12 10 4 Usage of Lock Unlock IN4 IN6 inputs with lock unlock feature sss sese eee eee eee 13 10 5 Automatic arming of the security system Auto rearm sese eee eee eee eee eee 14 10 6 Enabling of the security system via IN6 input Force ARMing TuncOn sss eee 14 10 7 Blocking ARM INS additional Teatre sss sese 14 10 8 Bell confirmation signal by arming disarming the security SSG sss sees eee eee eee eee 14 i Mode IVES a E E A EN A E 14 LlLl Eg ivalent mput did CLAIMS s pes5ccsaceasevncataneaceceacunine iaoeiai e sa Haasa iE e aeaaaee ybebeaicislnstnehepbebuennies 15 I2 Sensorconnection digrais smsen iassa sa Hn aeaii e aaaea ag ieena ninnaa 15 11 3 Input configuration parameters cacesoceccetarsacercaeuane vsabnacsdecsisanentenerievedcteviedutsbseicadeatvetaatancasadeastusedbebeacaslnstneierienuendes 16 11 4 Voltage measuring IN7 internal esse 16 11 5
19. M operator may be changed or simply the amount of DIAL repetitions reduced Parameters of the module are set by sending SMS or via PC by using standard miniUSB cable and configuration software SERA which is available to download at www topkodas t Page In order to activate voice listening it is necessary to call from a user s telephone number When calling the module will immediately activate voice listening which will last as long as the user will reject the call or when the module will start performing other commands Calls from other telephone numbers of non authorized users are ignored 5 Package content GTAUTO module 1 pcs System cable Ipcs GSM antenna 1 pcs fs C Or 2 2 kOhm resistors 4 pcs 1 kOhm resistors 6 pcs ee Cee Oey System state indicator LED attached on the system cable 1 pcs Mini CD 1 pcs a e User s guide in PDF TE Mini USB cable amp Prosim SERA Shipping Package e USB drivers Note Some package content may be optional Please ask seller for more information External temperature sensor attached External microphone attached on the on the system cable 1 pcs system cable 1 pcs Automated GSM security and control system www topkodas It gt 6 Specifications Parameters of built in GSM module Quad band 850 900 1800 1900 MHz Sending of SMS messages Receiving of calls and dialling Microphone Outputs OUT OUT4 max current sss eee eee V 1500 mA OU
20. RESET button GSM antenna connector SIM card holder of Push Push type 9 Power supply and input output connector 7 1 Meaning of LEDs Name Indication variations Meaning Flashes remains lit for GSM module is in ARM security mode 50ms turns off for External LED on the 300ms las C ARM Blinking remains lit for GSM module is in DISARM non security mode state 50ms turns off for 10s Off Program error processor is out of order hardware problem or power supply failure Blinking remains lit for The module is functioning WDG green built in 50ms turns off after LED 1000ms The module is out of order or no voltage Lights continuously Modem has been registered to the network Flashes remains lit for Modem is being registered to the GSM network 50ms turns off for 300ms Modem failed to register to the network Power supply OK and the module is registered to the GSM E network A a ee Lights continuously Modem power supply is OK but the module failed to register to LED the GSM network Modem power supply failure or it is switched off WDG REG Turns on each 500 ms The Bootloader mode In this mode it is possible to update the firmware of the module 7 1 Input output connector pinouts meaning and layout ba Wire colour Description a re 11 V_ Red Positive supply voltage Power supply voltage B I6V o o 2 input Green Yaliow i ronevinput NONOEOL E 6 OUTI Grey __ First output 1500mA O
21. SERA The module is considered to be equipped properly and communications is reliable if all sent SMS and calls are properly received as well as all user commands are being performed 17 5 Installation instruction and connection diagram of security system for house mini mobile cottages boats It is recommended to use standard motion fire glass breaking sensors For powering of sensors we recommend to use standard 6 8 wires cable for designed for installation of security system For sound signalling we recommend to use siren DC12V up to 1500mA It is recommended to connect the siren to the system by using 2x0 75 sq mm double insulation cable It is possible to supply the security system from stabilized power supply source 10 15V and not less than 1 5A It is necessary to calculate max current of power supply The current of the alarm system is the current used by sensors relays siren and other devices It is most convenient to use power supply source applied for power supply of security systems with the option to connect backup lead battery It is recommended to mount remote control relays into sockets Sockets may be easily fixed in metal box It is necessary to select relays according to preferred voltage and current Auxiliary BUZZER is recommended to be installed inside the premises not far from the entrance Buzzer operates together with the main siren also when the system starts calculating the time to leave the premises and the time till
22. TI OUT4 are protected from overvoltage overcurrent and overhearting All outputs can be controlled via short call DIAL or via SMS message This feature may be used for gate opening ignition locking etc Output alarm parameters may be programmed Programmable algorithms for outputs operation CTRL SMS DIAL SIREN BUZER ARM state Zones OK Light Flash inverting pulse mode INI IN6 inputs SMS text for input alarm and restore Programmable enabling or disabling of inputs Input type NC NO EOL Algorithm for zones operation delay interior instant 24 hours silent fire Response time Time of additional response Commutation of selected out put IN7 voltage control internal power supply voltage input Alarm voltage programmable Restore voltage programmable Programming based voltage calibration Power supply voltage range esse eee eee eee from 8 0 V to 16 V Measurement scale oo ce ceceeceececcecceccecsceccecceccscscscesceecscssessescesceses 0 01V Temperature control parameters External temperature sensor Alarm temperature programmable Restore temperature programmable Programming based calibration of temperature sensor Temperature measurement range sese eee eee eee eee from 40 C to 80 C Measurement system eee eee eee Fahrenheit Celsius Me s rement scale aisarssazcesmasaasennspondeabbeonstanponadeatannstonnetadhesomuiegaapisacoananes 0 1 C 0 18 F Module control ARM DISARM of the security system vi
23. Topkodas gt UAB Topkodas GSM SMS DIAL security and remote control system User s guide Prog Version GTAUTO v4 APPLICATION The module may be applied for remote monitoring and control of vehicles motorcycles boats or other transport facilities as well as for their protection via GSM network For remote monitoring of premises and for control via GSM network Remote control of the devices via GSM network Access control Gate door control Automation of premises temperature and voltage control GSM thermostat for premisses and heating systems Remote voice listening FEATURES Adaptive control of alarm system ARM DISARM Not necessary additional key switch The module may turned ON OFF by using manufacturer s central lock 6 inputs Fully programmable zones 2 inputs for arm disarm the security system The module can be controlled using standard central lock of a vehicle or using other access control device 4 programmable 1 5 OC outputs for remote control or for fulfilment of selected function 1 output for monitoring of system s state LED indicator 16 users who receive information about protected object Reception of information in a form of SMS or via DIAL short call 400 users being able to control gate or electromagnetic lock via free short call ARM DISARM of the system via free short call ARM DISARM of the system with the factory remote control central lock Temperature measurement For temperature con
24. USER 123456 59 1 More info see 7 2 10 3 ARM DISARM by using Lock and Unlock inputs It is possible to ARM DISARM the module by using Lock and Unlock inputs These inputs may be used when it is necessary to control the module via any additional external access control device having NO or NC output e Vehicle s central lock signal e Access control device e g RFID IBUTTON keyboard e Itis possible to use switch button reed switch etc for generating of control signal Several Lock Unlock modes are available e Mode 1 V Pulse using Lock and Unlock inputs Lock input sets ARM mode after pulsing or steady signal Unlock sets DISARM mode It is comfortable to use Ist or 2nd mode when connecting the Automated GSM security and control system www topkodas lt 12 module to the central lock of vehicle Central lock mostly generates lock and unlock signals with two wires e 2nd mode 2 V Pulse using Lock and Unlock inputs similar as 1 mode only inverted e 3rd mode 3 V Level using Lock input used only one Lock input Unlock input is not used These modes are comfortable to use when activating deactivating the system by using switch or other access control device e 4th mode V Level using Lock and Unlock inputs similar as 3rd mode is only inverted e 5th mode V gt 500ms Pulse Lock input uses only one Lock input Unlock input is not used The ARM DISARM state might be changed via voltage pulse longer than 500ms The voltage puls
25. a LOCK UNLOCK outputs 6 control algorithms Two condition inputs used via SMS message via short call DIAL Automatic periodical test Test sending in a form of SMS message Sending communication control messages tests at time range from 1 to 24 hours after pressing RESET button or after entering into ARM security mode Settings discreetness one hour Power supply voltage Nominal power supply Voltage sss eee 12 6 V Power supply voltage range esse eee eee eee 9 16V Consumption current In standby ea een ne mre ee me rae tre ne ene Poe a ree entre Tenens eae eee ee less than 30 mAT In dialling or SMS sending mode sss sese sesseeseeeeecceeeeeeeeeeeaas less than 300 mA Environmental parameters Storage temperature range from see 40 to 85 C 40 iki 185 F Operational temperature range from sss eee eee 30 to 75 C from 22 to 167 F Max relative humidity under 40 C 104 TP 95 Automated GSM security and control system www topkodas It 6 Module 1 siorino aE a AE S 112g Overall dimensions of the module s 90x63x32 mm Current consumption in idle running depends on inputs connection type on output state and load 7 General view of the product and layout of control devices TAAA EA TGR BRAS AGS Ae EEE A ow t RRR ae 89 199 9 9 Jers u EN Automated GSM security and control system www topkodas lt Oy ae a REG yellow LED WDG green LED MOD red LED MiniUSB programming connector
26. alarm response of the security system after entering the premises see clause 7 1 It is possible to use buzzer of Hitpoint PB12N23P12Q or similar modified piezoelectric 12V DC 150mA max Buzzer Automated GSM security and control system www topkodas It 26 OC iren AC 110 220V Unloc n e SATII ITI AAAA no no gnition Out ns Transformer 18 24V a Backup Battery 12V MICROPHONE E l Le n L TR Sl fe D Ea EB am oO mia mlizo 2 Black D EW External oO T a power supply nm IN K Temperature sensor Black White ea t 2 Z 5 z 5 a BEL 5 E BUZZER Se 7 Sean Ses Sed Sos oO N E SIE E L ae oie 5 vw lo Ole Gls Gls Slt n x N E 2 wel KA US BH Roe T TRR 1 COM amp V S N G E 1K K S IK 7 1 me 1K eet wen l 12V ae COM 12V i COM COM COM COM COM Tamper Tamper2 Tamper3 ARM DISARM Any accsess O O O O O O COM control device RFID iButton NC NC NC Keypad with NC or NO output The module configuration blank sample for this diagram you will find after installing configuration program SERA located in the directory ConfigTemplates File name GTAUTO_v4_Boat_MobileCamper tcfg 17 6 Vehicle s GSM messages system Installation manual and connection diagram The module may be installed in all vehicles with petrol and diesel engines and 12V batteries negative pole
27. any GSM service provider with a possibility to send SMS and to call In order to control the module via a short call SIM card should be have Caller ID option Usually SIM cards have such option If your card can not identify a caller please contact GSM service provide or use another SIM card Locate SIM card into a holder Card s circuitry should look downward and card s key cut angle should look upwards The card holder is of Push Push type This means that after pushing the card once it is fixed and after pushing it again it is released Locate SIM card into a holder 2 Gently push it 3 Fix SIM card T Note do not locate SIM card with force because you may damage SIM card holder Locate SIM card into a holder Gently push it Fix SIM card Note do not locate SIM card with force because you may damage SIM card holder 17 2 Configuration and control of GSM communication module via SMS messages Only basic parameters of the module shown in the table 17 1 may be configured via SMS messages All parameters of the module may be changed via USB by using configuration software SERA Configuration of the module via SMS messages may be performed only with installer s password 17 1 The table shows configuration and control codes of the module Configuration of the module may be performed via SMS messages Configuration command SMS structure Verifier INST Installer s commands This verifier is used for configuration
28. aware USER password e Authorized user is a person whose mobile phone s number is entered in GSM module Two authorized users with the same rights may be entered into the module e Configuration programming of the settings which will define the operation of the item For example user s telephone numbers set up of periodicity for sending SMS message input names etc Event event a user receives the information about ARM status of the security system The module is in ARM mode DISARM status of the security system The module is in standby mode only 24h inputs are active NO input type Normal Open this means that the alarm will be send when the input will be connected with ground V NC input type Normal Close this means that the alarm will be send when the circuit between input and ground V will be broken EOL end of line resistor input type with resistor Service messages ARM DISARM test resetting of the system DIAL the system makes a call to the number specified Pull up resistor is that it weakly pulls the voltage of the wire it is connected to towards V or whatever voltage represents logic high MIC microphone COM negative power supply terminal V positive power supply terminal SSR Solid State Relay Caller ID Caller s identification 4 Short description of the operation principle GTauto further referred to as the module transfers messages about events of the sec
29. d user s telephone number the end symbol e 00l user ID number from 001 to 400 In this example the telephone number of Ist user is entered the end symbol e 000100 What actions should be done after making call to a user Sequence from the left to the right OUT1 OUT2 O0UT3 OUT4 ARM DISARM MIC 0 active functions 1 non active function In the example the function ARM DISARM is selected 5 Delete user s for remote control via short call telephone number according to ID number or all numbers at once Delete user s telephone number whose ID number is 001 It is possible to select from 001 to 400 INST123456 61 001 Delete all telephone numbers of remote control users from 001 to 400 Automated GSM security and control system www topkodas lt 21 INST 123456 62 6 Inputs programming INST123456 11_ 00000111_12 01101111 80 1 INST user s type installer 123456 installer s code space character 11 command see table 17 1 space character 00000111 used inputs are calculated from the left to the right IN IN2 IN3 IN4 IN5 alarms are disabled and IN6 IN7 IN8 alarms are enabled space character 12 command see table 17 1 space character 01101111 IN1 IN4 restores are disabled IN2 IN3 INS IN6 IN7 IN8 restores are enabled space character 80 command see table 17 1 space character 1 will send command code 05 12 parameters back to SMS sender More input parameters ma
30. d GSM security and control system www topkodas It 17 14 Automatic periodical test sending Periodical test may be used for communication control of the module Test sending time is programmable Test Time Asynchronous periodical test may be programmed This means that after each activation of the system test time is being calculated from the beginning Reset test counter ARMing Test sending may be disabled by setting time 00 Periodical test may be used for SIM card s account control The following parameters of the module are available in a test message GSM communication strength power supply voltage temperature IMEI number of the module software version 15 Messages sending Messages are being sent in the event of alarm after ARM DISARM of the security system if specified in the configuration upon test sending time if specified in the configuration after changing the module configuration if specified in the configuration upon sending request about parameters command code 80 SMS about alarm of the security system is doubled with a short telephone call if specified in configuration 16 Remote control of the module via SMS messages or via short call With the help of SMS messages it is possible to control devices connected to outputs Out Out2 Out3 Out4 It is possible to ARM DISARM the security system Control command for user USER are available in the table No 18 2 The amount of users when controlling via SMS i
31. e E mene lacedua oct lt cuaudeqpcsdutus onsedeqadeatomeneaadacpaesseadeasaleqavamnete cane teqrenseipe easedeuns 31 Dg 5 1111 eaves tessa terrasse ear cinerea eae cee Seaman EE E EE A EEE E E E A E E 32 Automated GSM security and control system www topkodas It 3 1 Safety requirements Before applying the module in operation please read this user s guide Any operations related with mounting of the module and connecting of peripheral devices should be performed only after unplugging the module from the mains 2 Application of the device GSM security module GTAUTO hereinafter the Module is applied for transferring of GSM SMS messages to the mobile phone of a user GFAUTO module may be used for protection of various vehicles The module may be used for protection of a vehicle or in combination with the vehicle s security system which has control lock control The module may be applied for protection of house garages cottages vehicles as well as for access control gate control objects automation smart house and temperature control For premisses protection and many other applications In the event of burglary the device depending on programmed operation algorithm is able to call or to send SMS to up to 16 users A user is able to hear what is going on premises after answering a call or he may make a call by himself A user is able to receive an SMS with detailed information about status of each protected zone and number of alarm event
32. e might be generated by using switch or other input control device e 6th mode V gt 500ms Pulse Lock input similar as 5th mode is only inverted 1 2 3 4 5 6 see diagrams in annex 2 Lock and Unlock inputs do not have built in Pull Up resistor When there is no external signal you need to connect external 2 2K pull up resistor The resistor should be connected between power supply positive terminal V and input Such event may occur when switch is connected between lock input and ground as shown in Fig 10 1Fig 10 1 Example of wiring diagram with two switches One switch for ARM ing another DISARM ing Ist or 2nd modes should be set by using two switches V Pull resistor 2 aK L Pull resistor 2 aK ence Fig 10 1 Example of wiring diagram with central lock of vehicle see annex 1 10 4 Usage of Lock Unlock IN4 IN6 inputs with lock unlock feature Lock Unlock condition is used when a user does not want the security system to be activated deactivated by using door lock or central lock button In such event the module will analyse signals from door and central lock and will not allow changing ARM DISARM mode This feature will protect a vehicle from disabling DISARMing the module via the lock or button in the event of breaking window and pressing central lock button or lock spinning For lock unlock blocking condition it is necessary to use IN4 or and IN6 module inputs These inputs are config
33. e user is able to hear short repetitive sound signals When 10 seconds are left till the begging of activation signals are being repeated each 0 5 seconds If after expiry of the delay time all zones remain unalarmed the system turns into ARM state along with beep sound to confirm the action ARM state state of alarm system ARM DISARM May be used for light indication When the output is set to operate in pulse mode this feature may be used to close car windows or sunroof on arming Impulse time should be set 20 30 seconds On arming the output will generate signal to close windows Inputs OK if any of zones is disturbed the output will be alarmed This feature is usually used for indication whether all zones are in order Light Flash used for connection of light signal Upon alarm of the security system the light starts blinking Lights will also blink when arming disarming the security system This feature may be applied to connect vehicle direction signals e Output inversion e Output type level or impulse e Output impulse duration 1 65535 seconds 13 Timers of the security system Entry Delay time period during which the user after passing Delay zone should manage to disarm the security system Exit Delay time period during which the user should manage to leave the object and pass Delay zone Siren time Siren switch on time in the event of alarm Test time time of automatic periodical test Automate
34. ed Automated GSM security and control system www topkodas It 16 12 Programmable outputs The module GTAUTO has 4 programmable outputs Outputs of the module may be used to switch relay LEDs siren or other sound device Current for OUT1 OUT4 is 1500mA All outputs are protected from short circuit over voltage and overheating 12 1 Equivalent output diagrams OUT I OUT4 outputs is open collector in terms of grounding V All outputs have current limitation from 1 5A also protection from overvoltage and overhearting OUTI OUT4 equivalent diagram GTAUTO COM OUT1 OUT4 12 2 Output connection diagrams Examples of output connection diagrams see below 1500mA GTAUTO 1500mA GTAUTO OUT1 OUT4 OUT1 OUT4 C V Siren V COM V COM 12 3 Operational output parameters The following parameters may be set for each output e SMS text for ON output state e SMS text for OFF output state e Output operation algorithm OUT def O CTRL SMS DIAL output used for remote control via short call or SMS E g for ignition blocking for gate control or for remote vehicle starting etc SIREN output used for connection of siren Siren time can be changed BUZER sound signalling device In the event of zone alarm beeps continuously When security system starts calculating exit delay th
35. ed after alarm response of the Site aeaa gt aeaa security system or following test messages schedule The number of users up to 7 IN Pins a s e Jv IN4 ear V N4 ear 16 It is possible to select what event SMS to be send to each user Z INS M N5 Iv ING M ING System Voltage Y System Voltage K Temperature IV Hlemperature lv ARM V ARM JV DISARM DISARM IV Service Service Ie TEST een 8 3 Remote control Users who are able to control the module via short call The number of users up to 400 These users are able to control outputs via short call to activate voice listening and to activate ARM DISARM mode of the system Action of the user is free to select The actions to be done by the module after the telephone number having been recognized might be assigned to every telephone number The following actions may be selected regarding telephone number of each user e To activate outputs OUT1 OUT2 OUT3 OUT4 optionally This function might be used to lock a vehicle s ignition to start a vehicle and for remote control of other equipment e ARM DISARM security system e Activate voice listening via external microphone MIC Automated GSM security and control system www topkodas It 9 9 Temperature control and maintenance Heating and cooling system control Temperature control with GSM phones GTauto thermostat measure temperature through a probe that is on system cable and can drive any of outputs OUT1 OUT2 OUT3
36. el with other security system For example if default security system is used in a vehicle thus bell signal may be used for IN6 of the GTAUTO module If default security system will be alarmed for appropriate reasons and will activate the bell thus GTAUTO module will automatically turn into ARM state And will send all information in relation to alarmed sensors Thus the user gains additional protection from undesirable deactivation of GT AUTO module This IN6 feature may be disabled 10 7 Blocking ARM IN5 additional feature This is additional feature IN5 which enables to block activation of ARM State This feature may be applied in vehicles by connecting IN5 input to ignition If GTAUTO module was deactivated and after ignition was turn on thus while the ignition will be on the module would not be able to enter into ARM state This feature may be disabled 10 8 Bell confirmation signal by arming disarming the security system The siren will generate confirmation signal when arming disarming the security system if function Siren signal on ARM DISARM was selected in the software SERA When the security system is to be turned in ARM mode the bell will beep once when in DISARM mode the bell will beep twice 11 Module inputs The module GTAUTO has e 6 programmable external inputs zones e 1 temperature sensor input e Measuring of power supply voltage Internal input is visible in programming table e 2 control inputs Lock
37. ers saloon and sources of electromagnetic disturbances auto computer air conditioning system relay units Automated GSM security and control system www topkodas It 29 Do not mount the unit directly to metal parts of the vehicle in order to avoid accumulation of condensate within system block The module should be mounted thus connectors of wires to be at the bottom side Wires of the security system can not be laid near moving or hot parts of a vehicle For fastening use screws or plastic fastening straps The battery should be installed in a place protected from impact of humidity or other materials causing corrosion as far as possible from heating elements of passengers saloon It is necessary to install fuses mentioned in the diagram Fuse seat should be installed as near as possible to the car battery 17 7 Testing and diagnostics Diagnostics and testing of the module may be performed via USB port with software SERA The software will show system input output GSM states in real time Thus it would be easier to evaluate whether the module operates as appropriate atx File Setup Devices Update About n System Options Testing window GSM Communications utputa states IZ Out Out Onsott a59772030884440 SM cardi READY Signal lewel 4 7 PTT TT Td Z Outs Outs Onit Registration Registered home network SMS Service Centre Address 370695399992 14 O outa OUL OnIGOTT 1023 1 nek 1023 Unlock
38. m voltage 13 16V Temperature 26 1 C IMEI 356895030001799 HW GTauto SW GTauto v4 110801 24 6 9 satisfied signal correspond to two bars on the monitor of a mobile phone 10 14 good signal correspond to three bars on the monitor of a mobile phone 15 and more excellent signal corresponds to four bars on the monitor of a mobile Voltage Voltage of car battery or other power supply source the module is connected to Temperature temperature sensor s showings C or F IMEI IMEI number of GSM modem HW hardware version SW software version System state request according to the command USER 123456 80 7 USER user type 123456 user code space character space character 80 command see table 17 1 7 command system state request The module will sent two part message to the number the SMS was sent from Below you will see the example of received SMS message following request command USER123456 80 7 The first of two SMS State ARM In1 Luggage closed In2 Bonnet closed In3 Door closed In3 MicrowaveRestore INS Ignition OFF The second of two SMS Inputs In6 Siren OFF In7 Battery restore Output states Out OFF Out2 OFF Out3 OFF Out4 OFF system state state of the first input state of the second input state of the third input state of the forth input state of the third input state of the seventh input state of the eight input s
39. one will not be responded if alarm of Delay type zone occurred and Entry Dlay or Exit Delay time still have not run out Such type zones may be used for connection of motion sensor in front of the door The input will be activated immediately if the door has not been opened before o Instant Instant zone Upon disturbance of this zone the system will immediately activate burglary alarm o 24 hours Upon disturbance of this zone the system will activate burglary alarm not depending whether the security system is in ARM or in DISARM modes The applications of this type zones are safes storehouses tampers of the sensors o Silent silent zone is always active not depending on whether the security system is ARM or DISARM Upon disturbance of this zone SMS messages are being generated but the siren will not be activated These zones may be applied for voltage temperature control AC mains failure control and for alarm of silent panic o Fire this zone is always active not depending on whether the security system is ARM or DISARM The zone generates a special siren signal with interruptions The zone is applied for smoke sensors and for fire alarm e Enabling or disabling of zone alarm or restore e Input speed time of the input reaction this is the time period during which changed input state should remain stable in order to let the module to register alarm or restore input state e Repeat time this is the time pe
40. ontacts can not exceed 300 Ohms Resistors should be mounted as near the sensor as possible Improper connection of resistors system will not work properly Pull Up resistors should be 2 2 KOhm V V A A Pull Up resistor Pull Up resistor 2 2K 22K IN1 INS IN1 IN5 IN6 NC NC NO NO CO CO iee CoM V V A A Pull Up resistor Pull Up resistor 2 2K PAS IN1 INS IN1 IN4_ IN5 IN6 lt NC EOL NC EO NC EO IKI IK NC EOL COM COM COM ba COM x IK IK Automated GSM security and control system www topkodas lt 15 11 3 Input configuration parameters INPUT 3 Settings x me ean NG T Zone Type Door opened Alarm SMS Text Door closed Restore SMS Text Zone Options IZ Alarm Enabled Fone Speed 200ms mz IZ Restore Enabled Event Repeat Timeout 602 S Zone Action The following parameters may be set for all inputs e Text of SMS messages for alarms and restores This text will be included when sending SMS message to a user about alarms and restores of zones e Input types NC NO EOL These parameters should be set depending on type of zone connection e Definitions of input application o Delay Entry Exit zone Set Entry delay and Exit Delay are applied for this zone Such type zones are used for connection of door sensor o Interior disturbance of this type of the z
41. pen Collector Z o o SSS 8 LED K Black White ARM DISARM state LED cathode S LED A ARM DISARM state LED anode 9 Temp Black White MICP Black White Positive differential input of the microphone MICN Negative differential input of the microphone REG yellow built in LED Automated GSM security and control system www topkodas It 8 8 Users 8 1 Control and programming of the module via SMS messages 8 1 1 Installer Installer is able to execute all INST commands available in the table 7 The installer is able to change parameters of the module only with INST password 8 1 2 User User is able to execute only user s USER commands available in the table 7 2 A User may send SMS request any time and receive parameters of the security system zones and inputs states communication strength temperature etc SMS messages may be used to control outputs Out1 Out2 Out3 Out4 and to activate ARM DISARM mode A User is able to control the module only when using USER password x Please note that all phone USER Phone Number numbers must start with a e d U 8 2 Users to receive SMS DIAL messages f 44011 30000000 ee For example The number of users up to 16 These users are able to receive messages TTS or and calls after alarm response of the security system or communication test OF senda SMS calarmmRestore Dialing to USER alarmmestore 1 1 INT INT system state test messages which are being generat
42. riod during which repeated event of the input will be ignored e Zone action switching of selected output OUT1 OUT2 OUT3 OUT4 in the event of alarm or restore May be used for object automation For example for indoor temperature control Upon dropping of temperature will critical limit heater would be switched on automatically 11 4 Voltage measuring IN7 internal This input is visible only in configuration window of the SERA software of the module IN7 input is intended for power supply voltage control If the module is being applied for the security of vehicle it is very comfortable to follow cat battery voltage A user will always be alerted that a car battery has been charged or discharged This the car battery will be protected from full discharge or damage Alarm and restore voltages are programmable Voltage measurement may be calibrated additionally 11 5 Microphone and voice listening The microphone may be connected to the system wire contacts 10 MICP and 20 MICN In order to avoid noises the microphone should be mounted as far as possible from GSM antenna 400 users are allowed activating voice listening in the objects In order to allow a user to activate voice listening it is necessary in user table GSM remote control to check the box MIC Note If a user number is enabled for ARM DISARM and MIC thus after making a call to the module the state ARM or DISARM will be changed and also microphone will be activat
43. s The user is able to control the device via SMS messages only if he knows user s password If a call is being performed from the telephone number not included in the system s data base the call is rejected immediately The module has system voltage control If power supply voltage drops below the defined value a user automatically will be notified via SMS The SMS message includes voltage of backup battery System Voltage The module has external temperature sensor A user receives information about temperature alarms and restores via SMS messages The SMS on voltage of the module and ambient temperature is also available Temperature may be measured in Celsius and Fahrenheit SMS periodical test ensures constant control of the module The module is able to send periodical test Test time is programmable The test will include all essential information GSM communication strength system car battery s power supply voltage temperature and IMEI of the module GTAUTO module is ideal for remote vehicle start up The module compares incoming number with programmed users numbers and in a case of coincide activates an output or other action and interrupts the call automatically All parameters of the module should be configured via PC by using software SERA or in remote manner by sending appropriate SMS including password 3 Used definitions and terms e Installer a person provided with INST installer s password e User is a person being
44. s unlimited Example of control command when changes the states of all three outputs and inquiry is made to send information via SMS about output states after changing of output states USER 123456 51 37 33 80 3 USER user type 123456 installer s code space character 51 changing of the first output state space character 52 changing of the second output state space character 53 changing of the third output state space character 80 information request command see table No 3 space character 5 to send information via SMS about output states More examples of controlling via SMS message see the chapter 7 2 All outputs may be controlled via short call the module will automatically reject the call Up to 400 users may control the module All users optionally may control outputs Outl Out2 Out3 OUT4 ARM DISARM the security system and activate voice listening MIC It is possible to assign to each user that he is able to control This is comfortable to use a single module for controlling of few gates when several masters are 17 Preparation to operate Before or after installation of the module it is necessary to configure its parameters SIM card settings may be configured by using only GSM phone How to prepare the module to operate e Connect system connector and GSM antenna e Connect power supply source 10 15V battery or stabilized 10 15V 1A power supply source Check and if necessary enter
45. ser type installer 123456 user code space character 70 the command to change overheating temperature alarm value space character 35 5 overheating alarm temperature value The end symbol Freezing temperature value upon reaching which the following SMS message will be sent Low temperature alarm INST123456_71_5 5 Temperature value for freezing equipment control INST 123456 72 28 5 Temperature value for heating equipment control INST 123456 73 21 7 More information about SMS commands see chapter 17 2 10 ARM DISARM of the module The module can work in ARM mode and DISARM mode ARM DISARM state of the module may be changed thus via short call via SMS message and by using Lock Unlock inputs All modes of ARM DISARM may supplement each other For example The module may be activated via Lock Unlock inputs and deactivated via short call or SMS message 10 1 ARM DISARM via short call It is possible for 400 users to activate deactivate the module via short call The module will recognize user s number and will automatically cancel the call Not recognized numbers are being ignored Information on how to program the user numbers is available in the description of SERA 10 2 ARM DISARM by sending SMS message It is possible to ARM DISARM of the module by sending SMS message and using USER or INST password Example of SMS message To ARM the system USER 123456 59 0 To DISARM the system
46. symbol Out2 output activation text changing up to 16 symbols the end symbol Out3 output activation text changing up to 16 symbols the end symbol Out4 output activation text changing up to 16 symbols the end symbol Outl output deactivation text changing up to 16 symbols the end symbol Out2 output deactivation text changing up to 16 symbols the end symbol Out3 output deactivation text changing up to 16 symbols the end symbol Out4 output deactivation text changing up to 16 symbols the end symbol 48 0000 1111 OUT1 OUT2 OUT3 OUT4 output states 1 Inverted 0 Normal Example outputs OUT1 OUT2 OUT3 OUT4are inverted Description of output Out1 Out2 Out3 Out4 operation algorithm 49 0000 1024 0 CTRL 1 SIREN 2 BUZZER 3 ARM state 4 Zones OK 5 Flash In the above example OUT1 will operate in siren mode OUT2 for remote control OUT3 to connect buzzer BUZZER OUT4 Zones OK 1 OUT1 2 OUT2 3 OUT3 4 OUT4 Change state of selected OUT output Output state changes every time after sending command code Explanation see below the table Activates or deactivates OUT3 output 0 deactivates 1 activates Activates or deactivates OUT4 output 0 deactivates 1 activates ARM DISARM command 0 DISARM the security system 1 ARM the security 59 none U or 1 ouian Command to enter new user for remote control via short call Command parameters none TelNo 001 000100
47. tate of the first output state of the second output state of the third input state of forth input System voltage State ARM Inputs In1 Luggage closed In2 Bonnet closed In3 Door closed In4 MicrowaveRestore In5 Ignition OFF Inputs In6 Siren OFF In7 Batery restore Output states Out OFF Out2 OFF Out3 OFF Out4 OFF The module is considered to be installed properly and communication is reliable if all messages and calls are received properly and all user command are being executed properly Automated GSM security and control system www topkodas It 23 17 3 Configuration of the module via PC The module may be configured and tested via PA by using standard miniUSB cable This configuration is being performed by using the software SERA which you may download at www topkodas It More info about the module configuration by using SERA program see SERA description l IO x File Setup Devices Update About aal el aal 2 yetem Options BR Zu stem Options SSM Renat gais GSM Alarm Security System Access Control Temperature Controlier p Inputs gt Temperature Controler Installer password p 6 symbols RIT r Service SMS Text rerz Custom SME Test User password 6 symbols HW GTAUTO i Testing and Diagnostic Ta ime 24 h Reset test counter after arming Boot GTAUTOdboot 10 LockUnlock Mode 1 V Pulse using Lock and Unlock inputs Sat GTAUTO v4 1108015 Entry Delay 5 Z E
48. trol tracking alarm and control Voltage measurement Voltage monitoring and alarm External microphone Remote voice listening option via external microphone Option to connect BELL for sound alarm System state BUZZER Optional output type FLASH feature may be used for direction indicators on arming or disarming or in the event of alarm Optional output type Sending of periodical test including system parameters SMS about state of each sensor alarms power supply voltage and GSM communication level Built in GSM module Testing and diagnostic of the module via USB by using program SERA Remote set up via SMS messages Configuration of the module via USB Standard mini USB cable may be used Free configuration program SERA Very compact Automated GSM security and control system www topkodas It 2 Content b SAS By Pe QU CIM Us sereen a EE EEEE E EE OEE O E E 4 25 APPin oree V O eeren E a E EE E E E E E A E 4 E ASCO CHIN OMS and Ter erasia E EE E T EE 4 4 Short description of the operation principle T 4 ig Parre 6 IMS ON TTT 5 i PS TM AUS T 6 7 General view of the product and layout of Control devices sese E 7 1 Input output connector pinouts Meaning and layout sese sss sees 8 8 RTT 9 8 1 Control and programming of the module via SMS messages sse eee 9 Gkal MSA nr E E ERE NE dn eachewnsdannd desceseowenedeerdnseachownsdened Sescecmeweredeernsee 9 N T RT E E NA EE ENA S NA A N E S A S sdaseoousesesaseeess 9
49. ule in operation none Remote module reset Reset by using SMS message 1 Programming of users telephone numbers to send SMS and to make a call INST123456_01 37011111111 01 INST user s type installer 123456 installer s code space character 01l command code programming of users numbers space character user s telephone number without comprised of country code operator s code and user s telephone number the end symbol e 0l user ID number 01 16 In this example the telephone number of Ist user is entered After the telephone number has been entered all events of the security system will be sent to a user Optional events to be send may be selected only when configuring via USB 2 Itis possible to delete telephone numbers one by one according order of priority or all 16 numbers at once INST123456 02 15 INST123456 02 15 Delete user s telephone number whose ID number is 15 It is possible to select from 01 to 16 3 INST123456 03 Delete all 16 users telephone numbers INST123456 _03 4 To enter user s telephone number for remote control via short call INST123456 60_3701111111 001 000100 LA LJ INST user s type installer 123456 installer s code space character 60 command code programming of users telephone numbers for remote control via short call space character 3701111111 user s telephone number without comprised of country code operator s code an
50. ured like additional input function The following conditions might be set e Unlock Blocking condition e Lock Blocking condition e Lock Unlock Blocking condition Automated GSM security and control system www topkodas lt 13 V GTauto GTauto Pull U UnLock Conditi ob V gag nLock Condition H Door lock UnLock Condition gt me F contact for IN4 contact for Unocking A Unocking 7 L A Central lock switch H Al o contact in passenger V S Central lock switch compartment contact in passenger for Unlocking Pull U compartment 22K for Unlocking Lock Condition oo v Door lock _ N contact Lock Condition 7 Door lock for locking IN6 ass N L for locking Central lock switch V z 4 j ee i Central lock switch compartment V for locking aca j o Lock for locking Cok da T i A AN Lock signal Pull Up 2 2K Unlock i 20 V Unloc UnLock signal A UnLock signal 10 5 Automatic arming of the security system Auto rearm If the function Auto reARM is on the module will automatically return to ARM state if during Entry Delay none of zones was alarmed This feature is active only if the module was deactivated via telephone DIAL or SMS This protects from casual disabling of the system via telephone 10 6 Enabling of the security system via IN6 input Force ARMing function This feature is comfortable to use when the module operates in parall
51. urity system to the mobile phone of a user via GSM communication channel Upon alarm response of the security system the module will generate SMS message about alarmed sensors door capote shock fuel tank etc SMS message is being sent to a user in line with a short call This is to reduce the probability that a user will not observe SMS message It is possible to send SMS and to call to 16 users The algorithm of message sending is SMS1 SMS2 SMSn till all SMS messages will be send After DIALI DIAL2 DIALn All messages are being sent until all users will be Automated GSM security and control system www topkodas It 4 notified about the event Preferred messages and texts of these messages should be defined when programming the module The module understands when the call is rejected and will not repeat calling When the module is calling to the user s phone the user can not reject the call at least 15 seconds Otherwise the module will understand that the user s number is busy and will try to repeat the call again In a case the user s number is busy in fact the module will make repetitive calls following the programmed number of calls Note Efficiency of this function depends on interpretation of call control by the operator in some cases the operator may wrongly interpret the call and thus the module will make repetitive calls each 60 seconds following the programmed number of repetitions by default 3 repetitions In such case GS
52. xt Delay f U Z S f 20 ld Siren signal on ARMIDISARM fecus Auto reSRM Temperature l Indication on off energy sawing See Modu PC time 201 1Uef2e 204714 COMMS if closed E Y Zee user manuals For details COMS Disconnected GTALITO v4 1108015 A 17 4 Installation of the product and connection diagram The module should be installed in such way to ensure GSM communication It is necessary to properly select place for GSM antenna GSM antenna can not be hidden deeply in metal constructions to prevent GSM communication screening GSM antenna should be mounted as fa as possible from electronic sensors shock microwave microphone temperature sensors etc because GSM electromagnetic field may disturb operation of sensors or other electronic devices We are not liable for disturbances related with your GSM communication service provider Connection diagram is available in the annex however other connections versions are also possible Fuses are necessary In order to check operation of the module it is necessary to activate used sensors door shock sensor etc and to observe their operation The user should receive messages a about alarmed zones depending on programming If SMS messages have not been received please check GSM communication and whether the module is configured properly by sending 80 command with 1 2 3 4 5 6 7 parameters We recommend to check configurations of the module and test with the software
53. y be changed via USB 7 Programming of input names INST 123456 21 Alarmluggage 22 Alarmcapote _ 23 Alarmdoor 80 2 8 Output names programming INST 123456 40_ ignition on _43_ ignition off _80_4 INST user s type installer 123456 installer s code space character 40 command see table 17 1 space character ignition on name of output state when ignition is on space character 43 command see table 17 1 space character ignition off name of output state when ignition is off space character 80 command see table 17 1 space character 4 will send 40 49 parameters of command codes 9 Programming of output parameters INST 123456 48 1010 49 1053 80 4 INST user s type installer 123456 installer s code space character 48 command outputs inversion see table 17 1 space character 1010 OUT 1 inverted OUT2 normal OUT3 inverted OUT4 normal space character 49 command description of operation output algorithm see table 17 1 space character 1053 OUTI siren OUT2 remote control OUT3 light signalling device FLASH OUT4 ARM State space character e 80 command see table 17 1 e space character Automated GSM security and control system www topkodas lt 22 e 4 will send 40 49 parameters of command codes 10 Module control modes ARM DISARM see diagrams2 in the annex INST 123456 05 1 INST user s
Download Pdf Manuals
Related Search