ICON® ELSINORE bOOT
Contents
1. E ETE COM ti i CE PERSONAL PROTECTIVE EQUIPMENT USER MANUAL ELSINORE BOOT MOTORCYCLISTS BOOTS DIRECTIVE 89 686 EEC CATEGORY II STANDARD EN 13634 2010 NOT TO BE REMOVED EXCEPT BY CONSUMER NOT TO BE REMOVED EXCEPT BY CONSUMER MIEN ICON ELSINORE BOOT MOTORCYCLISTS BOOTS PERSONAL PROTECTIVE EQUIPMENT USER MANUAL STANDARD EN 13634 2010 DIRECTIVE 89 686 EEC CATEGORY II PPE The Elsinore Boot by Icon is considered Personal Protective Equipment PPE as defined by European Directive 89 686 EEC The protective footwear described in this manual is considered Category 11 PPE and as such may only display the CE Marking after having undergone an EC Type Approval and subsequent relevant Certification at a Notified European Body Placement of the CE Marking on the protective footwear indicates conformity with the Basic Health and Safety Requirements of Directive 89 686 EEC The protective footwear described in this manual has undergone EC Type Examination at Ricotest s r l Notified Body number 0498 to assure compliance with Directive 89 686 EEC It has additionally been examined and tested to assure its compliance with technical Standard EN 13634 2010 Protective Footwear for professional motorcycle riders Requirements and test methods SAFETY WARNINGS USE RESTRICTIONS AND LIMITATIONS Use of Elsinore Boots is strictly limited to on road motorcycling Elsinore Boots are designed to offer l2. gt 2 5 resistance Area B Remainder of boot upper Level 1 2 5s Level 2 2 12s Upper is classified based on the lowest result obtained in either area A or B For a definition of Area A and B see Fig 1 and Chart 3 below Impact cut 4 4 5 mm Area A Achilles and instep Level 2 resistance Level 1 x 25 mm maximum knife penetration Level 2 lt 25 mm maximum knife penetration Area B Remainder of boot Level 1 lt 25 mm maximum knife penetration Level 2 lt 15 mm maximum knife penetration Upper is classified based on the lowest result obtained in either area A or B For a definition of Area A and B see Fig 1 and Chart 3 below Chart 2 Elsinore Boots Type Examination Test Results According to EN 13634 2010 Test EN 13634 2010 Reference Unit Requirement Result Sole Transverse rigidity of footwear 6 1 kN Level 1 2 1 0 kN Level 2 Level 2 2 1 5 kN Fig 1 Key 1 Zone 1 shin region 2 Zone 2 ankle region Area A m Area B Chart 3 Dimensions for Material Areas shown in Fig 1 Size Paris Points Size English 38 and Below 5 and below 40 120 39 42 5 5to 8 50 125 43 and above 8 5 and above 55 130 The lower tangen the ankle as felt of Zone 2 is used to define the lower limits of measure ment E amp F Zone 2 is located by centering po
3. Rule In general all PPE should be replaced at least every five years even if the PPE has not suffered any damage Damage may be present and may not always be identified by a simple visual inspection 05 06 PERFORMANCE Elsinore Boots have undergone EC Type Examination to assure compliance with Directive 89 686 EEC They have additionally been examined and tested to assure their compliance with the appropriate technical Standard European standard EN 13634 2010 includes two performance levels in terms of the protection afforded The degree of risk or hazard that a motorcyclist will face is closely linked to the type of riding and the nature of the accident Within standard EN 13634 2010 Level 1 performance is deemed as the minimum level required in order for the footwear to provide useful protection in an accident and offers footwear with an optimum comfort level to suit all riding types Where riders feel that their riding style or sport exposes them to an increased accident risk Level 2 has been provided which offers increased performance however it is likely that this additional level of protection has an increased penalty for the weight and comfort so may not be acceptable to all riders Chart 2 Elsinore Boots Type Examination Test Results According to EN 13634 2010 Test EN 13634 2010 Reference Unit Requirement Result Upper Impact 4 4 4 seconds Area A Achilles and instep Level 2 abrasion Level 1 2 1 5s Level 2
4. ce the risk of injury to the area for which the PPE was designed to provide limited protection Misuse that will degrade Elsinore Boots performance Elsinore Boots must be worn to provide any protection Improper use of the Elsinore Boots can seriously compromise effectiveness and reduce performance In order for the Elsinore Boots to retain their original protective capabilities only use the Elsinore Boots for the purposes described in the Use Restrictions and Limitations section of this user manual Never tamper with any part of the boots Never bend or twist the boots excessively as this constitutes improper use Do not paint the boots or use colorants of any nature Environmental conditions that will degrade Elsinore Boots performance Contamination with foreign substances and or improper care can seriously compromise the Elsinore Boots effectiveness and reduce their performance Do not expose the Elsinore Boots to extreme direct sunlight or extreme moisture Do not expose the Elsinore Boots to extremely high or low temperatures like those found in a closed car or outdoor storage CARE INSTRUCTIONS Cleaning Use a suede leather safe cleaner on the exterior leather portions of the boot only Leather safe cleaners can be found at most shoe repair locations or retail stores specializing in leather apparel Use a rag dampened with clean water to wipe other exterior portions of the boot buckles plates or sole Note that leather safe c
5. e available from retailers Disposal At the end of the Elsinore Boots useful life do not discard them into the environment Dispose of them according to your local disposal requirements MATERIALS CONTENT This product contains no known harmful substances SAFETY WARNINGS WAIVER AND RELEASE BY OWNER NO PERSONAL PROTECTIVE EQUIPMENT IS ABLE TO SAFEGUARD AGAINST ALL IMPACTS NO PERSONAL PROTECTIVE EQUIPMENT CAN OFFER COMPLETE PROTECTION AGAINST ALL INJURIES MOTORCYCLING IS INHERENTLY DANGEROUS IN NATURE AND USE OF THIS EQUIPMENT CANNOT PREVENT INJURY OR DEATH WHEN USING THIS EQUIPMENT THE USER ASSUMES ALL RISK ASSOCIATED WITH THIS ACTIVITY WHICH MAY CAUSE INJURY OR DEATH THE USER HEREBY WAIVES ALL CLAIMS AGAINST ICONG A DIVISION OF LEMANS CORPORATION AND LEMANS CORPORATION FOR DEATH OR INJURY TO HIS OR HER PERSON AND HEREBY COVENANTS TO NOT SUE FOR ANY CLAIMS ARISING AS A RESULT OF INJURY OR DEATH WHILE USING ICON PRODUCTS 09
6. footwear size according to country The undesignated size denotes U S A sizing ABRIQUE EN CHINE PRODOTTO IN CINA MADE IN CHINA FABRICADO EN CHINA GEFABRICEERD INCHINA CREMNOB WTAE In addition to the markings described above the year and at least the quarter of manufacture will also be indicated on a separate label Some additional coded information which Icon uses to track the product may also appear The code may also appear in other versions of the marking 03 04 USE Selecting the Correct Size In order to ensure you choose the correct size Elsinore Boot MEN S SIZES lease see the table below PPE Position and Fit For PPE to offer the maximum protection poss ible PPE must be placed on the areas to be protected and PPE must cover the protected areas effectively If the protective features are already incorporated into the PPE then to be positioned correctly the PPE must be the correct size In all cases the proper equipment has been supplied to keep this PPE firmly in contact with the body Footwear Protective footwear fit is very impor snugly but not too tightly Confirm t on the outside of the boots by pu towards the toe of the boots and ou each strap onto its buckle post con rotective footwear that fits properly Any protective footwear Wearing Instructions and Adjustment Unzip the boot zipper located on the inside of each calf by pu ant The fi
7. imited protection in specific circumstances only Elsinore Boots are designed for use as on road motorcycling riding boots only Elsinore Boots are designed for use in addition to other personal protective equipment The addition of Elsinore Boots to any other PPE or on road motorcycling apparel being worn is not intended to imply that said PPE or on road motorcycling apparel is also CE approved On road motorcycling is inherently dangerous in nature and use of Elsinore Boots cannot prevent injury or death Icon strongly suggests always using multiple forms of PPE including an approved helmet jacket with approved impact protectors an approved back protector pants with approved impact protectors gloves and approved boots whenever engaged in on road motorcycling 01 02 CE MARKING SYMBOL KEY Below is an explanation of the CE Marking and other markings on the Elsinore Boot envisaged both by Directive 89 686 EEC and by EN 13634 2010 The CE mark is located on a label stitched onto the Elsinore Boots Example Marking for the Elsinore Boots RN 80725 CA 37038 PO XXXX DATE OF MANUFACTURE XX XXXX 29 9 5 UK A4 EU MADE IN CHINA FABRIQUE EN CHINE PRODOTTO IN CINA EN 13634 2010 28 JP FABRICADO EN CHINA GEFABRICEERD IN CHINA B Level 2 2 2 ere MENS HOIMIMES Chart 1 Label Explanation C CE mark to indicate that the protective footwear complies with the requirements or Directi
8. int X over the natural center of hrough the footwear when worn 07 08 SAFETY WARNINGS PROTECTION LIMITATIONS General Use Elsinore Boots are intended to protect against ambient conditions without excessively impairing the user s ability to control the motorcycle while operating the foot controls Elsinore Boots are designed with safety and dexterity in mind Elsinore Boots are considered to be PPE because they are designed and manufactured to provide imited protection to the foot and ankle during an accident or in the event of a fall from a motorcycle Additional particular hazards encountered during an on road motorcycle accident may include impacts with the rider s motorcycle conflicting vehicles and other roadside objects The chances of serious injury are increased if the foot becomes trapped under the motorcycle during a sliding impact Elsinore Boots will not prevent traumas caused by high energy impacts traumas caused by severe forces of bending twisting torsion or crushing as the result of striking an object or traumas caused by extreme movements The force levels used in the tests do not compare directly to the forces motorcyclists are exposed to in real world accidents therefore products that meet the requirements of the EN 13634 2010 Standard may only reduce the severity of some minor injuries No protective footwear can offer complete protection against all injuries the principle is to create a product that will help to redu
9. leaner may darken the leather of the boot Be sure to test any leather safe cleaner on an inconspicuous location first before cleaning the boot Do not use solvents or other toxic substances to clean the Elsinore Boots Do not use hair dryers or other heaters to dry the boots after cleaning Maintenance Regularly condition the exterior leather portions of the boots with a quality suede leather safe conditioner Apply suede leather conditioner to exterior leather portions only Do not apply leather conditioner to boot interior zippers hook and loop fastening material or sole Suede leather safe conditioners can be found at most shoe repair locations or retail stores specializing in leather apparel Storage Store the boots in a dry ventilated area away from sunlight or direct heat Ensure that they cannot be crushed hit dropped or otherwise damaged by impact and that they are not stored under heavy objects Do not store the boots with their weight distributed across a few single points only If wet after use before storing dry boots in a ventilated space at room temperature do not use hair dryers or other heaters Transport When transporting the boots do not leave them in a closed car for long periods of time and expose them to extremely high or low temperatures Ensure that they cannot be crushed hit dropped or otherwise damaged by impact and that they are not transported under heavy objects Spare parts Replacement buckle kits ar
10. re detailed above while choosing different adjustment strap holes For maximum protection and safety the protective footwear should not cause any discomfort and should not reduce the rider s freedom of movement or restrict the reach to or operation of the motorcycle controls while in a normal riding position If you are unable to find a proper fit in this protective footwear style please try another CE certified protective footwear style SAFETY WARNINGS SAFETY INSPECTIONS AND OBSOLESCENCE Before Every Use Check the sole to confirm that it is good condition and attached securely to the boot Check the lining to confirm that it is not ripped or torn Check uppers and adjustment straps to confirm that the leather is not cut or cracked Check the zippers buckles and adjustment straps to confirm that they are not broken that they are not filled with debris and that nothing prevents them from fastening securely Protective footwear that is improperly fastened cannot protect the user If the protective footwear or any parts of them become worn replace the footwear immediately In the Event of an Impact In the event of impact the key elements of the protective footwear may become compromised and the protective footwear may no longer provide the limited protection described above The damage may not be visible to the naked eye In all cases of impact replace the boots Replacement Elsinore Boots can be purchased at Icon retail locations 5 Year
11. t of different protective footwear styles varies due to differences in design and construction Only use at does not fit properly should not be used Be sure that the protective footwear fits at heel lift is minimal Check to confirm adequate room in the toe box ing down on the zipper pull Release the leather adjustment straps from the buckles ling the leather straps away from the calf and off of the buckle posts and then sliding the adjustment straps from under the buckle flanges Insert foot pulling the boot on Slide foot all the way down in the boot Confirm oot fit Boot should feel snug on foot but not too tight Foot longer than the boot Close the zipper by pulling up on the zip sock material is caught in the zipper Reengage the adjustment straps in the boot buckles by inserting the adjustment straps into the buckles while ulling the adjustment straps rearward making sure the adjustment straps are completely underneath the upper and lower buckle flanges Then press irming that the buckle pos should be the same length as the boot without being too much shorter or too much er pull until the pull reaches the top of the boot Be sure to confirm that no pant or is inserted completely through a hole in the adjustment strap Check to confirm that wearing these boots does not reduce your ability to operate the motorcycle controls Fit may be adjusted by following the adjustment strap release and reengagement procedu
12. ve 89 686 EEC Pictogram indicating that User Manual Information Notice has been provided for this product 9 oto Specific symbol to indicate the protective footwear is for motorcycle use only EN 13634 Technical reference standard a EN 13634 2010 Level X X IPA IPS WR FO SRA SRB SRC B Indication of the protective footwear performance level in compliance with EN 13634 2010 X numeral denotes impact abrasion resistance level of upper X numeral denotes impact cut resistance level of upper X3 numeral denotes transverse rigidity of footwear IPA footwear meeting the optional requirements for ankle impact protection IPS footwear meeting the optional requirements for shin impact protection WR footwear meeting the optional requirements for resistance to water penetration FO footwear meeting the optional requirements for resistance to fuel oil SRA SRB or SRC footwear meeting the optional requirements for slip resistance B footwear meeting the requirements for uppers permeable to water vapor For further details regarding the performance levels of this protective footwear please see the section in this User Manual titled PERFORMANCE and Chart 2 included in that section titled Elsinore Boots Type Examination Test Results According to EN 13634 2010 Protective footwear name or Internal Manufacturing Code Manufacturer s name or logo 11 5 UK 12 lt MENS HOMMES Protective
Download Pdf Manuals
Related Search