Wireless Keychain Remote Control
Contents
1. Wireless Keychain Remote Control Model 3150C Operating Instructions and Owner s Manual Control Garage Door Opener and HomeSettings System from your car Thank you for purchasing the 3150C Wireless Keychain Remote Control HomeSettings products by Wayne Dalton allow you to control your home by remote control You can create a complete Home Control and Access Network by combining your Wireless Keychain Remote Control with other HomeSettings products Indoor and outdoor lighting security systems garage door openers and thermostats are just a few of the items you can easily control with additional HomeSettings products Your new Wireless Keychain Remote Control is compatible with Wayne Dalton garage door openers the Garage Door Opener Conversion Module and the Wireless Gateway to give you control of Z Wave enabled modules Home Control Basics HomesSettings products will allow you to easily control multiple devices in a home with the push of a button in what is known as a scene Turning on all of the lights as you come home is an example of a scene Dimming lights and closing your curtains to watch TV it s also a scene Visit www wayne dalton com access to get ideas on how to create scenes with your Remote Control and other Z Wave enabled HomeSettings products PACKAGE CONTENTS 3150C Transmitter Visor Clip Key Chain Ring User Manual X S Q Packages O2. Guljoousajqnol soinjea4 paoueapy Example of Use Single Big button is pro grammed only to activate Garage Door Opener while each of the two smaller buttons are programmed to SCENE 1 and 2 of the Gateway Module SCENE 3 of the Gateway module can be programmed to activate by pressing the two Press 2 Transmitter buttons smaller buttons at the same time at the same time Troubleshooting Problem Solution e The range of the transmitter is reduced 3 Replace Battery To change the batteries insert a coin in the coin slot and twist to access the battery compartment Your transmitter may use one or two CR2016 batteries Remove the batteries from the battery cage and replace with fresh batteries Be sure to maintain the correct polarity Coin Slot Troubleshooting Problem e One of my Wireless Gateway SCENES is not working e My operator no longer works with my remote The Wayne Dalton Wireless Gateway can be activated by up to 12 transmitter programs When exceeded the last one programmed will be dropped The Wayne Dalton operator can be activated by up to six remote control devices including wall station and keyless entry controls If a seventh control is programmed one of the programmed controls will be overwritten and will no longer activate the operator To clear the programming of all remote control devices press and hold the DoorMaster light fixture program button
3. Examples of Scenes The following examples describe how your Wireless Gateway can be used For further ideas please visit our website at www wayne dalton com access 1 Approaching your home in your car you wish to turn on the outside lights near the garage front door and rear door as well as a lamps in the kitchen and family room Wireless Gateway SCENE 1 can be programmed to turn all of these lights ON To operate SCENE 1 from your car you will also need to program one button of the remote located in your car to SCENE 1 2 In your car and leaving your home you wish to turn off the outside lights near the garage front door and rear door as well as interior lights and appliances and also turn on your security alarm Wireless Gateway SCENE 2 can be programmed to turn all of these modules OFF and to turn ON the security alarm To operate SCENE 2 from your car you will also need to program one button of the remote located in your car to SCENE 2 3 Noises outside your home awaken you during the night SCENE 3 is programmed to turn on only the outside lights You can turn on SCENE 3 with your Keychain Remote from your bedroom to illuminate the area and scaring off any potential intruders 4 Lights out You have tucked your 2 children in bed and one has your permission to read for 15 minutes while the other has your permission to watch TV for 15 minutes After 15 minutes you want to turn off their lights and TV SCENE 2 is prog
4. ME M eee 1 Wanmmgs andiGlosS Tk a eee ae 2 Se 0 Reenter rere en eee 3 4 DAES nee eee ee eee 5 Advanced grok 0 chee ae en ee pe eee 6 TOUBIESHOOUIIG seer cee en ere eter nnerenr nee eee eee eee 6 7 GOTO LANG Cease A A A E A 8 Look forthe Quick symbol for basic instructions Start Definition of Symbol AN Warning Installation Safety Precautions Never let children operate or play with door controls Keep remote controls away from AN children Fatal injury could result should a child become trapped between the door and the floor Always keep moving door in sight and keep people and objects away until it is completely closed To prevent serious injury or death avoid standing in the open doorway or walking through the doorway while door is moving GLOSSARY Copy See Replicate Delete Erase transmitter or SCENE information from Controller Also known as Exclude Device Any item that is connected to a module for example lamps Exclude Remove a module from the controller Include Add a module to the controller Module Any HomeSeitings or Z Wave product that is controlled with a HomeSettings or Z Wave remote controller A module can be part of more than one scene Network A collection of devices controlled by primary or secondary controllers operating on the same system A network has its own unique identification code so that no one else can control the system Operator Garage D
5. ed transmitter button s LED will turn off or idrive operator will beep once On the DoorMaster only release the transmitter button and press again LED will light briefly then turn off 4 Return the emergency disconnect handle to motor operated position 5 Press same transmitter button s again door should operate Transmitter is now programmed to operator 6 To OPERATE press the transmitter button NOTE idrive model only The first transmitter command after programming will only open the door through a six inch up down cycle Normal door operation will then occur on all subsequent transmitter commands TRANSMITTER BUTTONS PROGRAM IDRIVE TORQUEMASTER PROGRAM BUTTON BUTTON DOORMASTER QUANTUM amp CLASSIC amp PRODRIVE dn 19S Programming to Controller Use the following procedure to program the Wireless Keychain Remote transmitter button to a SCENE button on the Wireless Gateway WDHA 12R This procedure also is used to reassign a transmitter button to a different SCENE button 1 Press and Hold SCENE button you wish to program either Scene 1 2 or 3 until the LED turns off then immediately release the SCENE button Choose 1 2 Press and hold the desired Transmitter button SCENE button The LED on the Wireless Gateway will flash three 3 times quickly to indicate the programming is successfu
6. ence by one or more of the following measures a reorient or relocate the receiving antenna b increase the separation between the equipment and receiver c connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help IC Regulatory Information This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation of the device Cet appareillage num rique de la classe B r pond a toutes les exigences de Il interference canadienne causant des r glements d quipement Lop ration est sujette aux deux conditions suivantes 1 ce dispositif peut ne pas causer l interference nocive et 2 ce dispositif doit accepter n importe quelle interference re ue y compris l interf rence qui peut causer l op ration peu d sir e WARNING Changes or modifications to this receiver not expressly approved by Wayne Dalton Corp could void the user s authority to operate this equipment Copyright 2007 Wayne Dalton Corp Part No 0001766 RevA New 08 27 07 You can reach us via email at homesettings wayne dalton com for Consumer Assistance or online at www wayne dalton co
7. idrive Quantum or Classic drive operator program button for approximately ten seconds When the DoorMaster Quantum Classic drive status LED goes out or idrive operator beeps three times then all controls are erased Hurjooysajqnoly Covered by one or more of the following Patents D413 055 D413 579 D413 867 D421 031 D472 568 D472 910 D473 573 D473 574 D505 393 5 929 580 5 931 212 6 078 249 6 161 438 6 145 570 6 164 014 6 325 134 6 326 751 6 326 754 6 401 792 6 561 255 6 561 256 6 568 454 6 588 156 6 605 910 6 667 591 6 739 372 6 845 804 6 851 465 6 873 127 6 880 609 6 903 650 Other US and Foreign Patents pending FCC and IC Statement FCC Regulatory Information NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interfer
8. l 3 Release the transmitter button Transmitter Buttons Note Your Keychain Remote cannot directly operate Z Wave modules the Z Wave modules must be programmed to the Gateway Scene to which you have programmed your transmitter button 4 To OPERATE plug the Wireless Gateway into AC power then press the transmitter button corresponding to the programmed SCENE which you want to activate Best Practice Tip Program the garage door opener to a button by itself and SCENE s to their own transmitter buttons Programming to Conversion Module Use the following procedure to program the 5 Wireless Keychain Remote transmitter button to Y JY Program Button a Wayne Dalton Garage Door Opener Conversion Jp Module Model WDRR 372R This module will allow your Keychain Remote Control to operate any brand Garage Door Opener 1 Install the Garage Door Opener Conversion PEE EE neo aren Module per the instructions provided with it elpful hint A broom handle can be used to extend your reach for 2 Press and release the PROGRAM button on the depressing the program button Conversion Module The red indicator will turn on 3 Press and release the desired transmitter button Transmitter Buttons The Red LED indicator on the Conversion Module ear will flash to indicate as successful operation 6 To OPERATE press the transmitter button corresponding to the Conversion module d 38S
9. m access aoueljdwo
10. oor Opener Primary Controller The first controller used to set up your modules and network NOTE Only the Primary Controller can be used to include or delete modules from a network It is recommended that you mark the primary controller for ease in modifying your network Replicate Copy from one controller to another Scene A scene is a series of Z Wave modules programmed to turn to a specific level on off dim with the push of a button on a controller Secondary Controller A controller containing network information about other modules within the network and is created FROM the primary controller Secondary controllers cannot include or delete modules to the network Transmitter Garage Door Opener transmitter Asessoj5 buruse y Programming to Operator NOTE Any of the three transmitter buttons can be programmed to activate the door In multi door installations each button can be programmed to activate a separate door Only one button at a time per transmitter can be programmed to activate a door To program the transmitter 1 Place the emergency disconnect handle in the manual door operated position This is for Safety reasons 2 Press program button on DoorMaster light fixture idrive prodrive Quantum or Classicdrive operator LED will light or idrive operator will beep once indicating that it is ready to learn a transmitter 3 Within 30 seconds press and hold the desir
11. rammed to their bedroom lights lamps and to a TV in the childs room Using your Keychain Remote you can turn their lights and TV off Examples require the following modules 1 Wireless Gateway WOHA 12R 1 Keychain Remote 3973C or any built in vehicular remote control 3 Dimmer Switch Module HA O6WD for each light switch 2 Lamp Module HA O3WD for lamp in kitchen and family room 1 Wireless Gateway WOHA 12R 1 Keychain Remote 3973C or any built in vehicular remote control 3 Dimmer Switch Module HA O6WD for each light switch 2 Lamp Module HA O3WD for lamp in kitchen and family room 1 Wireless Gateway WOHA 12R 1 Keychain Remote 3973C 3 Dimmer Switch Module HA O6WD for each light switch 2 Lamp Module HA O3WD for lamp in kitchen and family room 1 Wireless Gateway WOHA 12R 1 Keychain Remote 3973C 2 Dimmer Switch Module HA O6WD for each light switch 2 Lamp Module HA O3WD for lamp in kitchen and family room 1 Appliance Module HA O2WD for the TV sojdwexy Button Combinations Use this procedure to program your Keychain Remote for up to 6 actions In any of the previous programming instruc tions at the point where you need to activate a transmitter button to complete the programming step simply simultaneously press a combina tion of any two buttons Then to activate that programmed action simultaneously press those two buttons
Download Pdf Manuals
Related Search