GSM Gateway
Contents
1.2. 4 Dimension Drawing 4 1 1 port 4 2 4 ports 8 ports Operation Manual 4 5 Demonstration on Double Sides of Equipment 5 1 1 port 1 1 Socket of externally connected antenna 2 DC 12V power input 3 PHONE Telephone PBX connector with standard RJ 11 USA type plug connected to the phone set or PBX 4 PSTN phone jack Central office line interface standard RJ11 phone jack 5 PWR LED Power Indicator 6 STATE LED Slow flashing during the initialization stage Light up when the phone set is picked up Fast flashing during the GSM line in use Flash timing indicates the RSSI received signal strength indicator 5 times per second for the strongest receiving time per second for the poorest receiving 7 PSTN LED Flashing during the PSTN line in use 8 GSM LED Fast flashing when the GSM channel is available otherwise slow flashing Insert the SIM card from the back take off the slide first MT 350 1 port Tnsert the SIM card in the front MT 354 358 Quad Octa Port Important You must off your PIN Code of your SIM Card by your cellular phone Operation Manual 5 5 2 4 ports 8 ports 6 7 8 9 10 1 Reset button After changed SIM card please press reset button for 5 seconds 2 SIM Card Please insert SIM card 3 PHONE Telephone PBX connector with standard RJ 11 USA type plug connected to the phone set or PBX 4 PSTN phone jack Central office l
3. it and its line connects to PSTN can it dial out A Yes it could yet is confined to dial out by PSTN only Q11 Can the phone make inspection on the echo signal of polarity reversal A Yes it could When call is dialed out through GSM the phone will make linear polarity reversal when it s called for echo response Q12 Does the machine deserve CLID function A Yes it does When GSM sends in call signal it will send the CLID out from phone by DTMF signal Q13 How to compulsorily dial out any number through GSM VPN A Wecan press before dialing out and dial phone number next to it Finally press ff to finish this task Operation Manual 18 16 Specification 1 Phone impedance under DC 1kQ AC 6000 exclude wire impedance 2 Phone signal receiving level 3dbm 24dbm 3 Phone signal time 50 100ms 4 Phone frequency error 1 5 Feed voltage 48V 6 Power converter Input 230 110 VAC 50 60 Hz 200mA gt Output 12VDC 1000mA 7 GSM specification 7 1 GSM Frequency bands Dual Band EGSM 900 and GSM 1800 GSM Phase 2 7 2 GSM class Small MS 7 3 Transmit power Class 4 2W for EGSM 900 Class 1 1W for GSM 1800 7 4 SIM card reader External connected via interface connector 7 5 Antenna 50Qantenna coaxial connector 7 6 Temperature range Normal operation 20 C to 55 C Restricted operation 25 C to 20 C and 55 C to 70 C Storage 40 C to 85 C
4. number setting 13 Call Transfer Restriction Setting Allow to setup 10 sets of number which are allowed to do call transfer from mobile to PSTN All calls from other numbers will transfer to phone set Restrict function setting Format wait for confirming tone 36aabb aa 01 means no restriction All calls from mobile will be transferd to PSTN 02 restrict the numbers set by function 37 see as below 99 clear all the restriction numbers bb should be the same as aa Default setting 01 all calls will be transferred Restrict number setting Format wait for confirming tone 37aabbbbbb aa should be 2 digits ranges from 00 to 09 as restrict code bbbbbb the number to be associated with the restrict code max 15 digits Note the function cod 99 reset to factory setting doesn t affect the restrict code number setting 14 Echo Cancel Function 4 20NNNNH NNNN 0101 Echo Cancel Enable Operation Manual 16 NNNN 0202 Echo Cancel Disable Default 0202 15 Q amp A Q1 PWR lamp doesn t light up after power on 2 A No power transmitted to power plug or the transformer is mal functioned Q2 No further vocal sound heard after picking up the phone A Phone line is disconnected or wrong wire connected Q3 Why the Busy Tone is heard directly wile picking up phone 2 Not linked to PSTN GSM isn t ready yet it might occur from the reasons of disconnecting antenna not
5. be forced to dial out from 11 11 Setting of Specific Call Transfer Dual band Only Tri band and SMS version dont Wave his A A 12 CLES EN DOGS aa arenes 12 12 ES Mires transfer 13 TS WOEE OGG Setting e bd o 14 13 Call Transfer Restriction Setting 15 Echo CAE cds 15 87242 COS 16 Operation Manual 1 1 Preface Congratulations You have selected the remarkable product GSM Gateway by your sharp and intellectual judgment This product will provide you the best wire and wireless communication services Before using this product you have to read over this Operation Manual letting this product serve you with its full functions to satisfy your ideal desire and enjoy yourself in the wire and wireless communication applied in daily lives The product is under our delicate design which has fulfilled the ideal way of communications expressed on the slogan of making wireless to wire versus making wire to wireless It can save your communication expense and bring you an unpredictable effort using this product 2 Function Interpretation 1 Conversion of wire amp wireless communication We can use GSM Gateway to apply conventional telephone set replacing cell phone to perform sending and receiving phone calls 2 Auto select econo
6. correct the will beep up once in response If not correct the then will beep up four times consecutively instead Default setting None 11 GSM simulated echo bell sound function Format Waiting for confirming tone 57aabb It s the function of dialing out phone call from GSM and generates echo bell sound before starting to talk in the phone aa means echo bell sound time in a unit of 0 1 sec 00 98 bb needs to be inputted identical to aa This function will disable if setting up to 00 If setting up to 99 it won t have time limit on it Notice that this echo function will be halt if there is actual echo sound reply or voice response occurred therein Default setting 00 turn off this function 12 GSM isn t ready call will be forced to dial out from PSTN Format Waiting for confirming tone 59aabb While GSM isn t ready the function will let the phone forcedly dial out from PSTN If aa is set to 01 it means that the call is not to dial out through PSTN and presented by the tone signal of busy line If aa is set to 02 it means that the phone call is forced to dial out through PSTN bb needs to be inputted identical to aa Operation Manual 12 Notice that this echo function will be halt if there is actual echo sound reply or voicel response occurred therein Default setting 02 forced to dial out through PSTN 11 Setting of Specific Call Transfer Dual ban
7. out code amount Format Waiting for confirming tone 7laabb aa means dial out number of call digits bb have to be inputted in exactly identical to aa Example 711010 which means setting dial out number of call digits 10 If correct will beep up once in response If not correct will beep up four times consecutively instead Default setting 10 2 Phone line Polarity reversing function Format Waiting for confirming tone 510101 is to turn the reversing function off 510202 is to turn it on default Default setting 02 Operation Manual 9 3 Definition of DTMF reversing signal Format Waiting for confirming tone 52aabb In some regions or systems DTMF reversing signals vary and be defined by this function aa 11 TONE 12 TONE 13 A TONE 14 B TONE 15 C TONE 00 D TONE bb needs conforming to aa Default setting 15 C TONE 4 Limit of communicating time Format Waiting for confirming tone 6 laabb aa means the communicating time in the unit of min 00 99 and will show alerting sound 30 sec ahead of disconnect bb should be identical to aa by input If setting to 00 it then means unrestricted Example 610505 which means that system will send out alert sound at the communicating time of 4 30 and hang up it at about 4 55 If correct the will beep up once in response If not correct the then will beep up four times consecutively instead Default setting
8. 00 5 GSM function of dialing out the prompt tone means this call is through GSM Format Waiting for confirming tone 530101 turn off prompt tone 530202 turn on prompt tone default Default setting 02 tum on this function 6 When not connecting to Telephone Office line PSTN GSM will provide the forced dial out function Format Waiting for confirming tone 550101 turn off function of forced dial out 550202 turn on function of forced dial out default Default setting 02 to turn on this function Operation Manual 10 7 Set up GSM extra dialing local code When both GSM and PSTN dial local code the difference between them is that GSM has to extra dial up local code whereas PSTN needs not This function applies to the condition that when PSTN has been cut and user dials local phone No system thus will add in local code automatically and dial out from GSM Format Waiting for confirming tone 63aabb aa means code limit There are still certain restrictions when auto adding local code such as that the service or emergent phone calls need not to add extra code dialing action This setting is that when the total phone number length inputted is shorter to the setting value then won t extra dial local code bb means local code 2 8 digitals it isn t contained in the original code while dialing out through GSM and will auto add it in advance Example 630604 if the prefix code isn t 0 04 an
9. GSM Gateway Operation Manual 4 ports 8 ports INDEX E S A E a N Pee eed erect 1 2 Function Interpreta da 1 Sans OL Equ deh ats 2 E Dimension Drawing 2 5 Demonstration on Double Sides of 0 0 0 0 4 6 Install Lane Connect AN 6 7 Set the AIN aaa 7 8 Code Conversion AAA sna 8 O Cancel Code da 8 Parameter oeno AA E EREET 8 1 Set GSM dial out code amount 8 2 Polarity reversing inc 8 3 Definition of DTMF reversing Small 9 4 Limit de e e 9 5 GSM function of dialing out the prompt 9 6 When not connecting to Telephone Office line GSM will provide the forced AECA et 9 7 Set up GSM extra dialing local COdS ooooooniocnnoccnoconoonncconnnonononnncconn nono connnnnonnnninos 10 8 Voice volume modulation ias 10 9 Restore defa lt setting e EENE Ur 10 10 Set up extra dialing local code to 22 22222224420424474 4 0000 11 11 GSM simulated echo bell sound 2 2 2 2 22 4 0000000 11 12 GSM isn t ready call will
10. Where 82 are function codes aa represents time delay to auto respond in the unit of 0 5 sec bb should be identical to aa Example 821010 it means that machine will auto respond after 5 seconds Example 820000 it means that after call is dialed out it can receive responding signal only when the other side of call makes corresponding signal Default value 10 sec later to auto respond it 2 3 DTMF definition of reversed signal Format Waiting for confirming tone 52aabb In some zones or systems various DTMF reversed signals can be defined by this function aa 11 TONE 12 TONE 13 A TONE 14 B TONE 15 C TONE 00 D TONE bb should be identical to aa Default setting 15 C TONE 3 GSM free transfer setup 3 1 Setup GSM to PSTN free mode Format Waiting for confirming tone 81 Waiting for prompt tone Once the GSM to PSTN free mode has be set all the incoming calls from GSM will be answered and prompt to enter password If the password is correct the calling party can hear the Bi tone then he she can dial out using the PSTN line To cancel this function press 81 3 2 GSM to PSTN free mode password setup Format Waiting for confirming tone 83aaaabbbb Waiting for prompt tone 83 is the function code aaaa is the password bbbb should be the same as aaaa Example 8312341234 means the calling party needs to enter 1234 for Operation Manual 14 password auth
11. able to receive signals or equipment mal functioned Q4 How to set up allow to dial number 2 A Step I connect a call receiver at phone Step II lift up phone Step dial and set up all to dial code after hearing beep sound then press again to confirm If we need to set up more than one allow to dial codes use to separate them off Ex 0910 beep 0920 beep It means that the allow to dial number is set to 0910 and 0920 Step IV hang up phone speaker and the setting process is over Q5 How to clear up the former setting of allow to dial 2 A Each new setting will auto cover over the former two settings Q6 How to quick sending out codes A Press after dialing out phone call it will be sent out immediately Operation Manual 17 Q7 how many allow to dial codes can this machine memorize 2 A 50 sets Q8 Can we use to fax or make data preparation Negative only can perform tone function exclusively 09 After setting up allow to dial code why we can t select the allow to dial route A 1 Check if line PSTN is connected properly 2 The allow to dial function hasn t been set up yet 1 not to follow the correct setup procedure processing setup 3 This machine derives the line malfunction inspecting ability If the line is out of order it will connect to GSM route in a forced way have to set up local code in advance Q10 If the has no power
12. d Only Tri band and SMS version don t have this feature 1 PSTN TO GSM The GSM GATEWAY can receive calls from PSTN and send them out through GSM Format Waiting for confirming tone 80nnnn Waiting for echo tone in responding Where 80 are function codes nnnn means the call number is to be dialed out To cancel this function press 80 Example 800911123456 represents that PSTN send in call can be dialed out to 0911123456 2 GSM TO PSTN 2 1 Setup GSM to PSTN assigned mode This machine can receive calls from GSM and dial them out through PSTN Format Waiting for confirming tone 81nnnn Waiting for echo tone in responding Where 81 are function codes nnnn means the call number is to be dialed out To cancel this function press 8 1 Example 810281112345 represents that GSM send in call can be dialed out to 0281112345 At some circumstances it needs to add in the last digital of PSTN number To input it press FP and to certify the input Example 810423210287 it means dialing out phone call to 0423210287 2 2 GSM call Transfer setting time to PSTN auto response When GSM phone call is dialed out through PSTN it doesn t have the responding signal in some practical applications and requires to use this function to auto respond a few seconds later Format Waiting for confirming tone Operation Manual 13 82aabb Waiting for echo tone in responding
13. d total code number isn t less than 6 then when dialing out form GSM it will dial 04 ahead of the other code numbers If correct the will beep up once in response If not the then will beep up four times consecutively instead Default setting 00 to turn off this function Note If it isn t connecting to PSTN then the phone won t dial out through GSM in case not setting up this function and not passing through the checking number of allow to dial code 8 Voive volume modulation 21 aabb aa means voice volume which varies from 00 04 00 is the bottom value and 04 is the peak one bb should be externally inputted identical to aa Example 210404 it means that the voice volume is set to the maximum value If correct the will beep up once in response And if not the then will beep up four times consecutively instead Default setting 04 it means that the maximum voice volume is set up 9 Restore default setting Format Waiting for confirming tone Operation Manual 11 990909 the only act needed to follow is to reboot machine 10 Set up extra dialing local code to PSTN Format Waiting for confirming tone 1 laaaaa aaaaa means the digitals dialed out with extra codes can extend to 12 digitals Example 111805 it means that if the phone number is dialed out with two prefix digitals of 02 08 through PSTN it will automatically dial out 1805 in advance If
14. e code that allows sending calls out from GSM Hang up the phone and the setting is thus completed When the coding number is altered follow the above steps to set up again X when nnnn is set to gt it will close the calls sending function from GSM Format waiting for confirming tone turn setting function on nnnn waiting for echo tone in responding Where nnnn means the allow to dial prefix code which as 0937 0948 are on behave of 0937 and 0948 the prefix code is dialed out from GSM Default setting 0 all call number starting with code 0 means allow to dial code Operation Manual 8 8 Code Conversion Setting Format Waiting for confirming tone turn setting function on aaaa Waiting for echo tone in responding bbbb Waiting for echo tone in responding Where aaaa means original code bbbb means converted code the 002 006 means converting prefix codes 002 to 006 automatically We have defined this code dialing mechanism outputting through Telephone Office line CESE system of PSTN If we want to output through GSM we can set the first code to such as H H 002 006 which means that will auto convert prefix codes 002 to 006 and dial out through GSM 9 Cancel Code Conversion Format Waiting for confirming tone turn setting function on Waiting for echo tone in responding is to cancel code conversion function 10 Set Parameter 1 Set GSM dial
15. entication Entering password has to be done in 30 seconds If no password is required press 83 Default password no password 3 3 Password prompt tone setup Format Waiting for confirming tone 84aabb 84 is the function code bb should be the same as aa 11 TONE gt 12 TONE 13 A TONE gt 14 B TONE 5 C TONE gt 00 D TONE 16 No tone Default value 15 C Tone emarks Interpretation of echo sound Command confirmed two beeps Setting is correct single beep Setting is error four consecutive beeps 12 Short Code Setting Allow to setup 100 sets of short code Once the short code has been set see function 31 below user may press 00 99 for fast dialing 0 9 are also accepted and regards as 00 09 The routing function applies to the setup number rather than the short code itself To enable disable the short code function Format wait for confirming tone 30aabb 01 for disable short code function 02 for enable short code function 99 clear all the numbers associated with the short codes bb should be the same as aa To set the number for short code Format wait for confirming tone Operation Manual 15 3 laabbbbbb aa should be 2 digits ranges from 00 to 99 as the short code bbbbbb the number to be associated with the short code max 15 digits Notice the function cod 99 reset to factory setting doesn t affect the short code
16. ine interface standard RJ11 phone jack 5 LEDs All LEDs indicating function are same as 1 port GSM Gateway 6 Switch Power Switch the AC input voltage 110v 220v 7 Antenna Connecting with antenna 8 ON OFF The switch of the AC power 9 Fuse If power failed please check the fuse 10 AC In Connecting with power cord Operation Manual 6 6 Install Line Connections 6 1 1 port Antenna PBX Wiring Diagram 1 Take apart your local PSTN connecting line from the phone or PBX and connect it to the LINE connecting slut of If you use to send and receive calls only then you don t need to connect the local PSTN line 2 Connect PHONE connecting slut to the inlet side of phoneset or PBX 3 Put in transformer power DC end connects to DC 12V of and then the PW lamp on the front side of should light up 4 will proceed with system detection after booting Please connect the Line and Phone correctly before energizing it If problem is found during the system operation please take power source off first and process wiring task next Operation Manual 7 6 2 4 ports 8 ports Sim Local PSTN Phone or PBX DES Antenna Power cord There are no different between 1 port 4 ports and 8 ports base on setting 7 Set the Allow to Dial Code 1 Hold the phone and dial numbers following the order illustrated below innnn n means th
17. mic route From various settings will determine the calls connected through local PSTN Line or GSM on accordance of call numbers dialed therein which can save phone call fee as a favorable benefit 3 Through the connection towards local PSTN line the phone calls will proceed with code transfer dialing process For example when you dial 002 will transfer it to 006 and transmit the calls through the other fixed communication network systems 4 Voice volume modulating system In order to cooperate with different application environment the Wizard is capable to modulate the voice volume of phone 5 MVPN Function Provide MVPN routing according to the prefix of MVPN number for GSM carrier Operation Manual 2 3 Parts Of Equipment After opening the package please check whether all parts attached to Wizard are provided in the package If there is any missing please query the sales agent promptly to supplement for the insufficient parts The parts on the list are specified below 3 1 1 port 1 The Main Device 2 Transformer AC DC 110V AC 12V DC or 220V 12 DC 3 Phone connecting Line 4 Antenna 5 This Operation Manual 3 2 4 ports 8 ports 1 The Main Device 2 Phone connecting Line 4 ports 4 lines 8 ports 8 lines 3 Antenna 4 ports 1 set 8 ports 2 sets 4 Power cord option European American Australian Standard 5 This Operation Manual 1 Operation Manual 3
Download Pdf Manuals
Related Search