M2000 Digital Indicator
Contents
1. 4 2 HIGH SPEED DIGITAL WEIGHT INDICATORS USER MANUAL FOR SOFTWARE VERSION 1 45 OR HIGHER RELEASE DATE 12 01 03 M2000 DIGITAL WEIGHT INDICATORS USER MANUAL Copyright 2003 Western Scale Co Limited All rights reserved Published by WESTERN SCALE CO LTD 1670 Kingsway Ave Port Coquitlam B C Canada V3C 3Y9 Information in this User Manual is subject to change without notice due to correction or enhancement The information described in this manual is the property of Western Scale Co Ltd No part of this manual may be reproduced or transmitted in any form without the expressed written permission of Western Scale Co Ltd FOR TECHNICAL SUPPORT REGARDING THIS PRODUCT PLEASE CALL YOUR M2000 SCALE SERVICE REPRESENTATIVE TABLE OF CONTENTS Introduction B edi EH e hase e e ena ba 2 Note To M2000 Users EET eR ERR HOMER SE add ehe 2 M2000 IridiCators 5 un OE hop t a exi e ab Sha 3 Receiving Inspection 3 M2000 User Interface etel s sd 4 Alpha Numeric Display 4 LED Indicator lamps kana aa mte 4 Function Keys oed atri DEAD ARRAS 6 dep ete Sa ASRS 6 ZERO SCALE iio Ie Bas 6 CLEAR key oderam up e Opes dn 6 TARE KOV coit ceto b2. z lt N eS nnn 6442000 HIGH SPEED DIGITAL WEIGHT INDICATORS TOTAL MODE EXAMPLE 2 3 Floor scales each using a channel on a single M2000 CH1 and CH3 are calibrated as 2000 x 2 Ibs CH2 is calibrated to 500 x 0 2 Ib As a result only Channels 1 and 3 will be included in Total Mode 1 Press 4 followed by the PRINT SELECT key 4 PRINT ToTAL sELECT 2 The CH1 and CH3 LED indicators will illuminate Nl 2 x th gt ow CH1 CH2 CH3 3 The weight on the display is the sum of these two channels SCALE OPERATIONS IN TOTAL MODE Pressing the ZERO SCALE button will zero all the channels that are part of the total The TARE function will tare all channels simultaneously displaying the total NET weight The MOTION and SCALE ZERO LEDs will indicate the status of all the scales that are part of the total TOTAL MODE must be enabled in Calibration before it can be used See Page 2 Note to M2000 Users TOTAL MODE cannot be used in legal for trade applications in Canada 5 PRINT SELECT USER MANUAL SCAN MODE allows the indicator to cycle between the scale channels that are enabled The M2000 will automatically switch the display to the next available channel and pause for 3 seconds before switching to the next channel To enter SCAN press 5 followed by the PRINT SELECT key Select a specific channel to stop scanning
3. Keypad may need replacement Remember that some keypad functions may be disabled Call for Service POWER PROBLEMS Proper steps must be taken during installation to prevent noise static or other power problems Consult your local M2000 dealer to ensure all power requirements are met For the best results have your system installed by a qualified scale technician It is important to note that in very noisy industrial environments power conditioning filters would be a requirement to ensure a fail safe operation under all conditions Indicators should not share AC power with electrical motors and switchgear Consult with the site engineer for clean AC power 19 6442000 HIGH SPEED DIGITAL WEIGHT INDICATORS 20 M2000 SPECIFICATIONS INDICATOR PERFORMANCE UNIT CONVERSION ZERO TRACKING Ibs kg 1 99 of d or 1 2 3d RESOLUTION M2000A RESOLUTION M2000D SAMPLING RATE SPAN STABILITY ZERO STABILITY LINEARITY CORRECTION CALIBRATION METHOD CALIBRATION SEALING FILTERING MODES FIRMWARE UPGRADING LOAD CELLS 520 000 A D counts per loadcell 256 000 A D counts per loadcell 100 times per second per AD channel 2ppm Celsius 5nV Celsius 5 span entries Calibration through software stored in Flash memory Class 1 Audit Trail System password protected FASTSTEP quick response Display from CH1 CH2 CH3 and TOTAL MODE All Channels Flash Memory In field Firmware upgrading witho
4. GROSS NET WEIGHING MODES 6 PRINT GR NET SELECT To change the weighing mode press 6 followed by the PRINT SELECT key If the M2000 has a tare value stored it will toggle between GROSS and NET weighing modes If no tare value is stored the M2000 will remain in GROSS weighing mode SELECTING POUNDS KILOGRAMS 7 PRINT Ib kg SELECT TEST DISPLAY 8 PRINT TEST SELECT To change the weighing units on the display press 7 followed by the PRINT SELECT key The indicator will toggle units from Ibs to kgs or kgs to Ibs Either unit of measurement can be set up as the default See Page 2 Note to M2000 Users To test the display segments press 8 followed by the PRINT SELECT key All the segments in the display will light up for a short period of time 11 6442000 HIGH SPEED DIGITAL WEIGHT INDICATORS TIME amp DATE ON THE M2000 M2000 Indicators have a built in Time amp Date Clock that is Y2K compliant and automatically adjusts for leap years The real time clock runs from a battery on the main board and will continue to operate when power is cut The M2000 does not have to be in Calibration Mode to change the time and date settings Access these Parameters as you do functions Number followed by PRINT SELECT SET TIME PARAMETER 80 Using the numeric keypad enter the new 6 digit time in the format shown below Press PRINT SELECT to save the new time or cancel at any time by pressin
5. en 15 Serial Communications 15 Barcode Scanners amp other Peripheral Devices 15 Industry Specific Programs amp 16 M2000 Option Boards ico topi otro rep 16 Filtering amp Adjustments 16 Entering Setpoint Values 17 M2000 User Trouble Shooting 18 M2000 Specifications zrs S a ae ee a aaae 20 2000 HIGH SPEED DIGITAL WEIGHT INDICATORS INTRODUCTION Thank you for choosing the smart weighing solution Utilizing over 25 years of research and development in electronic weighing systems M2000 high performance scale indicators are the industry standard for speed versatility and reliability From Truck In Out programs to Cattle weighing the M2000 can be custom tailored to meet the needs of all weighing applications With up to 3 independent scale channels and a totalizing function an M2000 can easily take the place of three other indicating devices M2000 indicators are easy to use and compatible with all scale systems making them ideal for new installations as well as upgrades to existing systems For a complete synopsis of M2000 Indicator f
6. Replace the battery with a type RENATA CR2450N 3V 540mAh lithium battery or equivalent This battery should be available at most electronics stores NEVER USE METAL OBJECTS SUCH AS SCREWDRIVERS TO REMOVE THE BATTERY THIS CAN RESULT IN PERSONAL INJURY AND OR A SHORT CIRCUITING OF THE BATTERY CAUSING DAMAGE TO THE INDICATOR 13 642000 HIGH SPEED DIGITAL WEIGHT INDICATORS ADVANCED M2000 FUNCTIONS The M2000 s advanced functions are accessible in Calibration Mode It is important that only qualified Scale Service Technicians access this mode This not only ensures the optimal performance of your weighing system but may be required under law in Legal For Trade applications Your M2000 trained Scale Service Provider will be happy to help you access all the features and functions required to maximize your system s effectiveness ELECTRONIC SEAL M2000 Set Up and Calibration settings are electronically sealed with a password This safeguard helps prevent accidental or unauthorized alteration of important scale settings Passwords are 4 digit numbers The factory default for the password is 1111 which can be changed in Calibration Mode To change or view the password in Calibration Mode consult a M2000 trained Service Technician IMPORTANT If you forget your password Calibration Mode will be inaccessible Contact your Scale Service Provider for assistance AUDIT TRAIL The M2000 is equipped with a Category 1 Audit Trail syst
7. in workmanship and matesials for the following peed and upon the following deseris and conditions 1 The waranty period is for 12 months commencing from the dade of delivery of the product io the purchaser 2 Western shall at i option repair o replace or mund the purchase price within a reasonable period ol time alter been notified of the alleged detest and after having eei reci that defect pursuant te this warranty in fact iE PDQ L mui SD unu ES ic Momo a ET C PALA TTA LT LIEU ie 5 Wester shall not be responsible kr ja consequential or special losses r damages sieh eg lass od use inconvenience commercial or economic kiss fb defects caused by misuse negligence modiGcation or neglect el improper operation mainbenance or repair This warranty shall have no force amd effect arl shall not apply there has been any unauthorted modification alteration or substitution of amy part or parts of the product ar b ihe serial number of ihe product has been altered or diaced in any manner whabsoewer 7 Noemployee or agent af Western has any authority fc add to subtract from or change any portion of this warranty and Westem s obligation herein is strictly limited io these terms as writer 8 enn rese or med by las eli po el the alleged defect must be ghen during the warranty dl will Rel ad ee Qr warranties expressed or by law ie
8. the M2000 The key must be pressed and held for 1 second to turn the M2000 off The ON OFF key is not hard wired to the M2000 power supply A Power Bypass function is available for Process Control and other applications See Page 2 Note to M2000 Users ZERO SCALE KEY Removes small residual weight values to return the displayed weight ES to zero The Centre Zero LED will be illuminated If the ZERO SCALE button is pressed in NET weighing mode the stored tare weight will appear as a negative weight on the display The scale cannot be zeroed if The ZERO key has been disabled The scale is in MOTION The residual weight on the scale is too great More than 2 of Scale Capacity Three rapid beeps will sound to indicate any of these conditions CLEAR KEY CLEAR Press the CLEAR key to erase previously entered tare values The CLEAR key will also function to cancel any keypad entry USER MANUAL TARE KEY D There are 2 methods used to tare the scale Method 1 Tare a random weight on the scale Place an item of unknown weight on the scale Container Box etc Press the TARE key and the displayed weight will be tared Note that the NET LED will illuminate to indicate that the scale is now in NET mode Method 2 Manually enter a tare With a stable weight on the scale enter the desired tare weight using the numeric keypad followed by the TARE key The NET LED will illuminate to indicate the scale is in
9. 000 Serial Communications offer variable output strings and support a wide range of protocols to easily integrate with any weighing system Transmit scale information directly to your Printer and or Remote Display Capture scale data for processing by a PC Data Controller or PLC The M2000 has two fully independent fully configurable serial ports COM1 and COM2 on the back of the indicator The factory default settings allocate COM1 for printing tickets at 9600 baud COM2 is allocated for outputting a weight string DF1500 in continuous mode at 9600 baud The COM Ports are programmable for RS232 amp RS422 capabilities Please note that Single Channel Models only have one serial port COM1 BARCODE SCANNERS AND OTHER PERIPHERAL DEVICES Combine your scanner and your scale to print out accurate product weight tickets The SMARTWIRE peripheral interface also provides easy connection and communication 15 642000 HIGH SPEED DIGITAL WEIGHT INDICATORS INDUSTRY SPECIFIC PROGRAMS amp FEATURES The Multi Purpose M2000 software package supports many industry specific features that simply require activation upon installation A variety of unique program configurations are available Examples include Truck In Out Onboard Weighing In Motion Weighing Cattle Weighing For further information regarding these programs contact your local M2000 dealer M2000 OPTION BOARDS 4 20 mA OUTPUTS The M2000 utilizes an optional 4 20 mA board to ge
10. CEIVING INSPECTION It is always good practice to verify that the M2000 Indicator Kit is undamaged upon receipt Check over packaging for any signs of damage Remove the M2000 indicator from its protective packaging and check for damage Each M2000 Indicator Kit should include M2000 Indicator 12 Volt Power Supply amp Power cord Slimline models only M2000 User Manual Capacity Label Set Removable Connectors for all M2000 terminals Correct number of cable strain reliefs For stainless steel enclosure models BE SURE TO CHECK THAT ALL NECESSARY OPTION BOARDS HAVE BEEN INCLUDED 642000 HIGH SPEED DIGITAL WEIGHT INDICATORS M2000 USER INTERFACE DISPLAY amp KEYPAD M2000 Displays are split into two components The Alpha Numeric Weight Display and the LED indicators ALPHA NUMERIC DISPLAY CHi CH CHS GR The Alpha Numeric Weight Display has 6 multi character LED s Scale weights Error messages and Calibration information See M2000 Technical Manual are shown here A negative weight is shown by a minus sign on the far left LED character The number of decimal points on the display is determined in Calibration Mode On power up a scrolling 12000 will be displayed followed by the software version number The scale weight will then be displayed LED INDICATOR LAMPS These triangular LEDs will illuminate to indicate certain scale conditions USER MANUAL SCALE CHANNEL 1 INDICATOR
11. NET mode If the scale was at zero the tare will be displayed as a negative weight The scale cannot be tared if There is a negative weight on the scale The scale is in motion The TARE key is disabled See Page 2 Note to M2000 Users PRINT SELECT KEY PRINT The PRINT SELECT key has two functions SELECT Function 1 PRINT a Weigh Ticket to a printer Press the PRINT SELECT key A ticket will be sent to the printer connected to an M2000 COM Port Please consult your M2000 Scale Service representative regarding printing information ticket formatting etc Function 2 SELECT a function Enter the function number on the numeric keypad followed by the PRINT SELECT key See Standard M2000 Functions Next Section 642000 HIGH SPEED DIGITAL WEIGHT INDICATORS STANDARD M2000 FUNCTIONS M2000 Standard functions are accessible via the keypad To prevent accidental misuse some standard functions may need to be enabled upon installation Additional fine tuning may also be recommended to maximize your weighing systems performance To get the most out of your M2000 discuss your system requirements with your M2000 Scale Service representative SELECTING SCALE CHANNELS M2000 Indicators utilize 3 independent scale channels Channel 1 is the default scale channel To view the weight display for the desired channel press the channel number on the numeric keypad followed by the PRINT SELECT key Note the app
12. and EXC to SNS Display shows RRRRRR Loadcell voltage range problem Call for Service Display shows EEEEEE OR 888888 The scale has been overloaded Remove weight from the scale immediately Check scale for damage Call for Service if necessary Display shows Scale Sections have not been allocated Digital System only Call for Service Will not Print The Scale Channel you are trying to print on is in MOTION or OVERLOADED Wait for scale to settle or remove excess load Cannot Zero Scale ZERO key disabled Must be enabled in Calibration Scale in Motion Wait for scale to settle Weight on Scale gt 2 of Scale Capacity To zero more than 2 Zero Range must be increased in Calibration Consult an M2000 trained Scale Technician SYMPTOM Cannot Tare Scale POSSIBLE PROBLEM Tare function disabled USER MANUAL PROBABLE SOLUTION Must be enabled in Calibration Scale in Motion Wait for scale to settle Cannot Tare a negative weight Remove weight clear scale and re enter Tare Cannot Select a Scale Channel Scale Channel is Disabled Scale Channels other than CH1 must be enabled in Calibration Mode Consult an M2000 trained Scale Technician Display segments missing LED may need replacement Use the TEST DISPLAY function to confirm Call for Service No response to Key presses
13. b Illuminated LED indicates the weight from Scale Channel 1 is displayed CH1 A blinking LED indicates motion on the scale SCALE CHANNEL 2 INDICATOR v Illuminated LED indicates the weight from Scale Channel 2 is displayed CH2 A blinking LED indicates motion on the scale SCALE CHANNEL 3 INDICATOR v Illuminated LED indicates the weight from Scale Channel 3 is displayed CH3 A blinking LED indicates motion on the scale GROSS WEIGHING MODE INDICATOR v Indicates the scale is in GROSS weighing mode No tare is stored GR CENTRE ZERO INDICATOR v Indicates scale is within 0 2 graduations of true ZERO May illuminate with a displayed weight in NET mode or if Tare Offset is being utilized NET WEIGHING MODE INDICATOR v Indicates the scale is in NET weighing mode Scale has a tare weight NET stored LB INDICATOR The scale is weighing in IMPERIAL units Pounds or a fraction thereof Ib KG INDICATOR v The scale is weighing in METRIC units Kilograms or a fraction thereof kg SCALE MOTION INDICATOR V Ablinking Scale Channel LED indicates MOTION on that scale CH3 TOTAL MODE INDICATOR W W W Multiple illuminated Scale Channel LEDs indicate TOTAL CH1 CH2 CH3 MODE Only those channels illuminated are included 642000 HIGH SPEED DIGITAL WEIGHT INDICATORS FUNCTION KEYS CH1 CH2 CH3 GR 0 NET Ib kg 5 7 8 SCAN Ibikg TEST ON 04 DER NUMERIC ON OFF KEY KEYS Pressing this key powers up
14. em The Audit Trail has two counters Calibration Counter Changing parameters that affect the calibration of weight will increment the Calibration counter by 1 Parameter Counter Changes to all other parameters will increment the Parameter counter by 1 Important Note Because the Audit Trail becomes active at the factory the counters may not initially show 0 even when the M2000 is new out of the box IT IS EXTREMELY IMPORTANT THAT THE CORRECT TIME AND DATE BE SET FOR THE AUDIT TRAIL TO BE ACCURATE THE AUDIT TRAIL IS PERMANENT AND CANNOT BE DISABLED OR ERASED BY REMOVING THE INTERNAL BATTERY USER MANUAL ACCESSING THE AUDIT TRAIL The Audit Trail can only be accessed from normal Weighing Mode 1 Enter 1000 followed by the PRINT SELECT The message Aud will briefly be displayed 2 Shortly after the M2000 will display in order the date of the last change made to the M2000 s calibration parameters the calibration CAL counter and the configuration CFG counter 031031 tR 00 PRINTING From simple weight printouts to customer designed tickets the M2000 prints to virtually any printer Utilize pre designed pre programmed industry specific tickets amp programs or the M2000 Ticket Formatter which allows for the easy creation of custom weigh tickets and reports Contact your M2000 dealer representative regarding the printing freedom the M2000 delivers SERIAL COMMUNICATIONS M2
15. g the CLEAR key For 12 Hour clock mode Parameter 83 must be used to select AM or PM L 2 Digit Seconds 00 59 2 Digit Minute 00 59 2 Digit Hour 01 12 or 00 23 EXAMPLE 11 00 AM PRINT PRINT SET DATE PARAMETER 81 Using the numeric keypad enter the new 6 digit date in the format shown below Press PRINT SELECT to save the new date or cancel at any time by pressing the CLEAR key YY MM DD L jJ 2 Digit Day 01 31 2 Digit Month 01 12 2 Digit Year 00 99 EXAMPLE OCTOBER 31 2003 3 1 3 1 fz CH1 SELECT CH3 CH1 CH3 CH1 SELECT USER MANUAL PARAMETER 83 TIME FORMAT MODE Description Controls Time Format settings 12 Hour or 24 Hour military time clock settings are available PARAMETER VALUE TIME FORMAT 0 default 24 Hour Mode 1 12 Hour Mode AM 2 12 Hour Mode PM BATTERY REPLACEMENT ON THE M2000 The M2000 uses a 3V Lithium Battery to run the real time clock and backup the indicators memory Power is drawn from the battery only when the indicator is disconnected from the 12V supply With regular use then the battery should have a long lifespan REPLACING THE BATTERY 1 Remove the M2000 s back cover 2 A coin sized battery is located in a battery holder Upper left corner of the M2000 PCB 3 Use your fingers to grab each edge of the battery 4 Gently pull on an angle removing the battery from the holder
16. ght for Setpoint 1 PARAMETER 52 Setpoint Value weight for Setpoint 2 PARAMETER 53 Setpoint Value weight for Setpoint 3 PARAMETER 54 Setpoint Value weight for Setpoint 4 PARAMETER 55 Setpoint Value weight for Setpoint 5 PARAMETER 56 Setpoint Value weight for Setpoint 6 EXAMPLE ADJUST SETPOINT 6 TO 1000 Ibs FROM 500 Ibs 1 In Weighing Mode verify the M2000 is weighing in Ibs If not switch weighing units 7 PRINT JSELECT 2 Select the Setpoint to adjust Parameter 56 for Setpoint 6 The display will show the current Setpoint Value nnn SCAN GR NET SELECT 3 Enter 1000 followed by PRINT SELECT 1 PRINT CH1 SELECT 17 6442000 HIGH SPEED DIGITAL WEIGHT INDICATORS 18 USER TROUBLESHOOTING FOR THE M2000 SYMPTOM M2000 will not power up POSSIBLE PROBLEM External power source failure PROBABLE SOLUTION Check Circuit Breaker Power Outlet 12V Power Supply failure Replace Power Supply M2000 will not turn off ON OFF key disabled The ON OFF key may be disabled for Process Control Applications Consult an M2000 trained Service Technician Display shows UUUUUU The loadcell cable to the M2000 has been disconnected or possibly severed No Signal Input Check terminal for disconnection If loadcell cable is damaged call for Service Sense lines from loadcell have not been terminated Connect Sense wires or jumper EXC to SNS
17. l the pra sions of ihe Sake of Goods Aa and In particular 20 thereof hereby specifically excluded WESTERN SCALE CO LIMITED 1670 Kingsway Avenue Port Coquitlam Vancouver B C a je s vm Lorie a ACER AL L i m Rr FEC
18. nerate an output current reflecting weight This typical industrial sensor protocol is useful in a broad range of applications SETPOINTS amp RELAYS The M2000 supports a total of 6 Setpoints that can be allocated to any Scale Channel The optional Setpoint board uses solid state relay modules to switch AC and DC loads REMOTE INPUTS The Isolated Input board allows the M2000 to accept remote input switch control Zero Tare Clear Gross amp Print functions are supported For further information regarding M2000 option boards contact your local M2000 dealer FILTERING AND ADJUSTMENTS M2000 Indicators have a high degree of compensation abilities and adjustability making them the industry s most versatile weighing element With ADVANCED SET UP FEATURES STATE OF THE ART FILTERING SYSTEMS and a GLOBAL COMPATIBILITY STRATEGY the M2000 can be fine tuned by Qualified Scale Technicians to perform at an elite level in all applications USER MANUAL ENTERING SETPOINT VALUES Setpoints should be installed and structured by a qualified Scale Technician However simple adjustment of the Setpoint weights can be done by the User Parameters 51 56 in Weighing Mode are used to enter Setpoint values The values entered into these registers will control the Setpoint relays NOTE THE UNITS OF MEASUREMENT TO ENTER A SETPOINT VALUE IN KILOGRAMS MAKE SURE THE M2000 IS CURRENTLY WEIGHING IN KILOGRAMS PARAMETER 51 Setpoint Value wei
19. o Sec decking 7 PRINT SELECT Key uuu actu petes EE ee 7 Standard M2000 Functions r 8 Selecting Scale Channels uuu u u a n 8 tota Modea ur ta dace bates 9 Total Mode Example 1 9 Total Mode Example 2 10 Scale Operations in Total Mode 10 SCAN Modes dotata 11 Gross Net Weighing Modes sss 11 Selecting IDS KQS 2 15 t t Sates 11 TESUDIS DIAY euma D I PE 11 Time amp Date on the 2000 12 SOU TIME AE NS 12 gt 12 5 EE 12 Example ceret Par aul eue e rey AA Pee a dE 12 Time Format tics usa matan Mie viii tie vete Vene Nava fessus D 13 Battery Replacement on the 2000 13 Replacing the 13 Advanced M2000 Functions r rrr 14 Electronic Seal 8 008 u t l i PRONUS 14 Audit Trail iii Rer DB RM DPA 14 Accessing the Audit Trail 15 PAIRING s Pere E ead EI p ee
20. ropriate Scale Channel LED indicator will illuminate PRINT SELECT CH1 CH2 CH3 GR 0 0 NET EI sui oe CH1 CH2 CH3 EI gt EI CH1 CH2 CH3 GR 0 NET Scale Channels 2 amp 3 must be enabled in Calibration Set up Mode See Page 2 Note to M2000 Users USER MANUAL TOTAL MODE SUMMING CHANNELS Up to 3 channels may be summed together to display a total weight Only channels that are enabled and calibrated with the same grad size decimal places and units of 4 PRINT weight will be displayed in TOTAL MODE TOTAL j SELECT Channel 1 is always included in TOTAL MODE TOTAL MODE is indicated when more than one of the Scale Channel LEDs are illuminated To return the M2000 to Single Channel Mode select a channel followed by the PRINT SELECT key TOTAL MODE EXAMPLE 1 A Truck scale with 3 sections Each section is wired to a separate channel on the M2000 allowing the operator to record the total weight of the vehicle along with the individual axle weights v SECTION 3 WIRED SECTION 2 WIRED SECTION 1 WIRED TO CHANNEL 3 TO CHANNEL 2 TO CHANNEL 1 3800 eppo UUU UUU IUUU 1 To view the rear axle weight Section 3 select Scale Channel 3 CH3 LED will illuminate v 3 E Y Y CH3 SELECT C H 1 2 C H3 2 To view the total weight Sum of all sections enter TOTAL MODE Press 4 followed by the PRINTISELECT key CH1 CH2 amp CH3 LEDs will illuminate
21. unctions or information on other custom weighing services please contact your M2000 dealer NOTE TO M2000 USERS This User Manual is intended for operational use by M2000 owners Information regarding standard indicator functionality is contained within Due to the important role weighing systems play certain functions and features of M2000 indicators should only be accessed by qualified Scale Technicians Specific information regarding Communications Enabling amp Disabling M2000 functions Scale Set up and Scale Calibration can be found by calling your Scale Service Provider For the best results have your system installed to your unique specifications by a qualified Scale Technician USER MANUAL M2000 INDICATORS The M2000 Indicator family includes M2000 A 3 Channel Analog Indicator 2 COM Ports One of the world s best and most affordable high speed fully featured indicators For use with Analog loadcells M2000 AS Single Channel Indicator 1 COM Port M2000 features and quality at a low cost For use with Analog loadcells M2000 D 3 Channel Digital Indicator 2 COM Ports Digital Communication with your scale for maximum lightning protection and data integrity Converts Analog loadcell signals to digital at the scale via the DLC Smart Box M2000 Indicators are available in a variety of enclosures including the NEMA rated wash down model NSS 1 Contact your M2000 dealer for details RE
22. ut affecting calibration data Up to 16 Loadcells using two DLC slaves LOADCELL INPUTS FULL SCALE 4 ranges 0 9mV 0 19mV 0 39mV and 0 79mV EXCITATION M2000D 5VDC 16x350 32x700 ohm in total EXCITATION M2000A 7 5VDC 16x350 32x700 ohm in total COMMUNICATIONS SERIAL OUTPUTS 2 full duplex RS232 RS422 1 only with Single Channel model INTERFACE SMART WIRE peripheral expansion RS485 multi drop EXTERNAL IO Bie SETPOINTS 6 channel Setpoint via SMARTWIRE optional EXTERNAL IO ANALOG OUTPUT 4 20mA board via SMARTWIRE optional EXTERNAL IO 1 DIGITAL INPUTS 6 optically isolated inputs via SMARTWIRE optional NETWORKING RS485 Multi drop Networking of up to 32 indicators as slaves ELECTRICAL POWER REQUIREMENTS 12VDC 1 Amp 1 5A maximum POWER DRAW 200 mA TEMPERATURE RANGE 10C to 40C RFI PROTECTION Filtered Signal Excitation amp Sense lines ENCLOSURES Wash down stainless steel enclosures Panel mount swivel bracket or STAINLESS desktop Light Stainless or NEMA 4 X ALUMINIUM Slimline M2000A only 12 GA Cast aluminium APPROVALS MEASUREMENT CANADA NTEP CSA CSA Approved Power Supply OIML Pending 1o new products sold by The following terns ol warranty r celled Wier unless Western Scale Co Limited otherwise specified in the terms of sake All new products ane warranted against defects
Download Pdf Manuals
Related Search