Installation and Operation Manual for High Speed Dome Camera VER
Contents
1. 120 S Timing actions for 7 days of programmable schedule Built in Semi conductor heater amp digital temperature sensor Pan Tilt accuracy 0 01 255 preset positions Multi Protocol through RS485 or coaxial cable Max 8 set of Group action can be stored This enables to move camera repetitively with combination of Preset A Group is composed of max 16 entities of Preset Max 4 of Patterns can be recorded and played back This enables to move camera to follow any trajectory operated by joystick as closely as possible Max 8 set of Swing action can be stored This enables to move camera repetitively between two preset positions with designated speed Max 1 set of auto scan can be stored This is to keep the ball machine according to the elevation angle of executive level 360 continuous rotation and speed can be adjusted 8 Privacy Zones with defined English camera title Auto Compatible PELCO_P PELCO_D compatible Guard Location the dome will rotate back to preset position after a period of vacant time Alarm triggering the alarm can trigger preset auto scan group and pattern tours functions Soft Address Function the use can set up the dome address without uninstall the dome Specially defrost function to get clear image when the camera is working on the low temperature environment High Speed Dome Camera Introduction Manual 4 Integrated Super Speed PTZ Rotator Delicate stepping motor stable sensitive and2. Freeze in Preset ON OFF UP AND DOWN TO SELECT At start point of preset movement camera LEFT AND RIGHT TO ENTER starts freezing the image of start point Camera keeps displaying the image of start point during preset movement and does not display the images which camera gets during preset movement As soon as camera stops at preset end point camera starts displaying live imageswhich it gets at preset end point This function availability should be different by models Auto Flip ON OFF When the camera tilts downward and goes just beyond the vertical position the camera will rotate 180 degrees Jog Direction INVERSE NORMAL If you set this to Inverse the view in the screen is moving same direction with jog tilting If Normal is selected the Dome Titl j j Dome Title view in the screen is moving reversely lt DOME TITLE gt Dome Max Speed 10 360 TITLE 2222999999 DOME TITLE OFF BACK EXIT Sets maximum jog speed Jog speed is inversely proportional to zoom magnification As zoom magnification OPEN SAVE CLOSE EXIT goes up pan tilt speed goes down Dome Title lt DOME SETUP gt lt ADVANCED gt gt lt DOME TITLE gt UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER Edits Label to show on monitor when preset runs MAX 10 alphabets are allowed Enter edit label cursor will be displayed on the screen using left right of joystick to select character and using up down to
3. II Specifications Product No 15 CD66WIB 15 CD66WB i i NTSC PAL 1 4 Interline CCD SCM 2270 SAMSUNG NTSC 768 H x494 V PAL 752 H x582 V SCM 2273 SAMSUNG NTSC 976 H x494 V PAL 976H x582 V CZ36SCM COP NTSC 1028 H x508 V 520K PAL 1028 H x596 V 610K Effective Pixels SCM 2370 SAMSUNG NTSC 768 H x494 V PAL 752 H x582 V SCM 2373 SAMSUNG NTSC 976 H x494 V PAL 976 H x582 V FCB EX1020 SONY NTSC Approx 380 000 pixels PAL Approx 440 000 pixels SCM 2270 SAMSUNG 560 TV Line SCM 2273 SAMSUNG 650 TV Line CZ36SCM COP 700 TV Line SCM 2370 SAMSUNG 560 TV Line SCM 2373 SAMSUNG 650 TV Line FCB EX1020 SONY 550 TV Line SCM 2270 SCM 2273 SAMSUNG x 27 Optical Zoom x 16 Digital Zoom ulimit eo SCM 2370 SCM 2373 SAMSUNG x 37 Optical Zoom x 16 Digital Zoom FCB EX1020 SONY x 36 Optical Zoom x 12 Digital Zoom SCM 2270 SCM 2273 SAMSUNG f 3 5mm 95mm CZ36SCM COP f 3 4mm 122 4mm Focal length SCM 2370 SCM 2373 SAMSUNG f 3 5 mm 129 5 mm FCB EX1020 SONY f 3 4mm 122 4mm Horizontal Res I I I I Xx ON LA ee ee Ration 50 dB AGC Off S N Min Illumination 0 2 Lux F1 67 50 IRE Color 0 02 Lux F1 67 50 IRE B W Day amp Night Auto Day Color Night ICR B W Auto Manual Semi Auto Ui Iris Auto Manual Semi Auto High Speed Dome Camera Introduction Manual 40 1 1 1 10000 sec ON Off Auto Manual Red Blue Gain Ad
4. ON OFF BACK Open or close the dome alarm function EXIT Alarm No 001 007 Select alarm channel number UP AND DOWN TO SELECT Alarm x Action NOTHING PRESET PATTERN SWING LEFT AND RIGHT TO ENTER GROUP Assign counteraction Preset position to each Alarm input Release Time 01 60 S Alarm output time is postponed to a certain time adjustable range is 01 sec to 60 sec Start Fan 20 60 C Ex If set start fan is 45 C the dome will start fan when above 45 C and it will stop to fan when temperature is lower than set value 5 C Defrost ON OFF Open or close the dome defrosting function High Speed Dome Camera Introduction Manual 38 I System Initialize lt SYSTEM INITIALIZE gt CLEAR ALL DATA NO CLR DISPLAY NO CLR CAMERA NO CLR MOTION NO CLR EDIT DATA NO REBOOT CAMERA NO REBOOT SYSTEM NO BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER The dome allows the user to reset its settings remotely under this menu Clear All Data Deletes all configuration data such as display camera motion setup and so on Clear Display Set Initializes Display Configuration Clear Camera Set Initializes Camera Configuration Clear Motion Set Initializes Motion Configuration Clear Edit Data Deletes Preset Date Swing Data Pattern Data and Group Data Reboot Camera Reboots Zoom Camera module Reboot System Reboots Speed Dome Camera High Speed Dome Camera Introduction Manual 39
5. UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER Displays system information configuration and date time setup Enable Disable of OSD display on Main Screen Enter into IR Setup menu Enter into Dome Setup menu Enter into Camera Setup menu Enter into Motion Setup menu Configure alarm action Initializes system configuration and sets all data to factory default configuration High Speed Dome Camera Introduction Manual 20 System Information lt SYSTEM INFORMATION The user can check the dome system information as required FIRMWARE VER 2 22 COLOR SYSTEM PAL The system information includes firmware version color system SN CODE 152859 PROTOCOL PELCOD poate anil Series code protocol 120ohm end resistor setup Date Time BAUD RATE 2400 120 RES OFF setup DATE TIME SETUP BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER Date Time Setup arate ime seu m Date Time Setup lt SYSTEM INFORMATION gt gt lt DATE MIME SETUP gt DATE 2015 03 06 TIME 08 00 00 The dome can display the data and time And the user could ah a enter this CLOCK menu to set up the DATE and TIME EXIT e Date 2015 03 06 OPEN SAVE CLOSE EXIT Move the cursor to Date move the joystick up or down to select the desired position about the date and then move the UP AND DOWN TO SELECT joystick lift or right to select corresponding date LEFT AND RIGHT TO ENTER e Time 08 00 00 Move the cur
6. 0055 BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER aSet North Direction Setup lt SET NORTH DIRECTION PTZ TO SELECT OPEN ENTER CLOSE EXIT 360 0 10 0 01X a Tilt Angle Setup lt TILT ANGLE gt TILT ANGLE 10 BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER N lt DOME SETUP gt gt lt PARKING ACTION SETUP gt Parking action setup means if there is no command for the dome for a period of time the dome will run the actions as defined Parking Action NOTHING To select parking action on off including NOTHING AUTO SCAN SWING1 8 GROUP1 8 PATTER1 4 PRESET1 8 Wait Time 005S 240S To select the waiting time for parking action function mSet North Direction lt DOME SETUP gt lt SET NORTH DIRECTION gt Set North to assign compass direction as criteria Move camera and press OPEN button to save a Tilt Angle lt DOME SETUP gt lt TILT ANGLE gt Set dome tilt angle Tilt angle 10 0 Move joystick left and right to select tilt angle High Speed Dome Camera Introduction Manual 97 gs ADVANCED lt ADVANCED gt lt DOME SETUP gt gt lt ADVANCED gt MOTION LOCK OFF FRZIN PRESET OFF Motion Lock ON OFF AUTO FLIP ON TOG DIRECTION NORMAL To set the motion lock on off If the function was turned on DOME MAX SPEED 360 lt DOME TITLE gt all of the scanning will be locked user can not delete such as BACK EXIT preset swing pattern and group
7. Introduction Manual 14 Dome Address Setup SW1 1 ID number of camera is set using binary number The example is shown bellow on tf 2 a 4 os 6 7 8 KL BM EN EN UN UN SES Ex 1 5 ON OFF ON OFF OFF OFF OFF OFF_ Ex ID 10 OFF ON OFF ON OFF OFF OFF OFF 2 The range of ID is 1 255 Factory default of Camera ID is 1 3 If you want to control a certain camera you must match the camera ID with Cam ID setting of DVR or Controller 4 Speed dome can change the ID address and baud rate via OSD menu Cabling Cabling Terminal Block Power Connection Please check the voltage and current capacity of rated power carefully Rated power is indicated in the back of main unit Rated Power Input Voltage Range Current Consumption AC24V AC24V 2V 15 CD66WIB AC24V AC24V 2V 15 CD66WB High Speed Dome Camera Introduction Manual 15 RS 485 Communication 1 For PTZ control connect this line to keyboard and DVR To control multiple cameras at the same time RS 485 communication lines of them is connected in parallel as shown below 2 Speed Dome OSD Menu support the distal 120R resistance of the opening and closing Keyboard Controller DVR Se a aa O M l M l M E l M aa d Yan h a wo wW oy k oy TERMIHAL RESISTOR 120R Video Connection Connect with BNC coaxial cable Alarm input Internal Terminal Connector INT S
8. OFF identify the location The dome supports 8 zone titles Please CLEAR ZONES CANCEL DELETE Zones No 01 08 BACK EXIT Move the cursor here Move a joystick left or right to choose the area of the need to set number 1 8 UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER o LeftLimit Move the joystick to right and enter into menu gt Left And Right Zone Setup press OPEN to save gt press CLOSE to exit lt LEFT ZONE SETUP Right Limit Move the joystick to right and enter into menu gt press OPEN to save gt press CLOSE to exit PTZ TO SELECT OPEN ENTER CLOSE EXIT Edit Label Edits Label to show on monitor when preset runs MAX 10 alphabets are allowed Enter edit label cursor will be displayed on the screen using left right of joystick to select character and using up down to move cursor After inputting press OPEN key to save and exit the setting S cd Bia ADEI Label Display ON OFF lt EDIT LABEL gt To switch on off the label display of zone LABEL BACK EXIT Clear Zones CANCEL OK Deletes data in current zone OPEN SAVE CLOSE EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER High Speed Dome Camera Introduction Manual 36 Timing Action Setup lt MOTION SETUP gt lt TIMING ACTION SETUP gt TIMING ACTION allows the user to set up the actions of the lt TIMING ACTION gt NO START STOP MOTION dome in 7 day
9. Preset numberjand press Enter lt Set Preset gt Press Preset input Preset number and press Enter lt Run Pattern gt Press Call input Pattern number and press Enter lt Set Pattern gt Please refer to the pattern setup turn to Pattern Setup If controller or DVR has no pattern button or function use shortcut keys with preset numbers For more information refer to Reserved Preset in this manual High Speed Dome Camera Introduction Manual 17 DI Starting OSD Menu Function Enter Menu Using the OSD menu Preset Pattern Swing Group and Alarm Input function can be configured for each application Press Call Preset Number 95 lt Enter gt Reserved Preset Description Function Some Preset numbers are reserved to special functions lt Call gt 95 lt Enter gt lt Call gt 51 lt Enter gt lt Call gt 52 lt Enter gt lt Preset gt 52 lt Enter gt lt Call gt 131 134 lt Enter gt lt Call gt 141 148 lt Enter gt lt Call gt 151 158 lt Enter gt lt Call gt 160 lt Enter gt lt Call gt 161 lt Enter gt lt Call gt 170 lt Enter gt lt Call gt 171 lt Enter gt lt Call gt 174 lt Enter gt lt Call gt 175 lt Enter gt lt Call gt 176 lt Enter gt lt Call gt 177 lt Enter gt lt Call gt 178 lt Enter gt lt Call gt 179 lt Enter gt lt Call gt 190 lt Enter gt lt Call gt 191 lt Enter gt lt Call gt 192 lt Enter
10. Sets digital zoom function to ON OFF If this is set to OFF PON optical zoom function runs but zoom function stops at the WHITE BAL IMAGE INTELL GENCE SPECIAL FUNC PAN HAN Day Night JAUTO DAY NIGHT Sets camera day or night mode end of optical zoom magnification EXIT SAVE DFLT Note CZ36SCM camera set using the embedded module itself menu settings High Speed Dome Camera Introduction Manual 29 m White Balance Setup WHITE BALANCE SETUPS lt CAMERA SETUP gt lt WHITE BALANCE SETUP gt WB MODE AUTO WB Mode AUTO MANUAL RED ADJUST 200 BULE ADIUSI 200 In Manual mode Red and Blue level can be set BACK up manually Red Adjust 50 200 Blue Adjust 50 200 UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER m Auto Exposure Setup lt CAMERA SETUP gt gt lt AUTO EXPOSURE SETUP gt lt AUTO EXPOSURE SETUP BACK LIGHT OFF Backlight ON OFF WDR OFF BRIGHTNESS 020 Sets Backlight Compensation SHUTTER WDR ON OFF AGC OFF BACK Wide dynamic range WDR balances thebrightest and EXIT darkest sections of a scene to produce a picture that is perfectly balanced in light and clarity UP AND DOWN TO SELECT Brightness 0 31 LEFT AND RIGHT TO ENTER Adjusts brightness of images Iris Shutter Speed and Gain are adjusted automatically in correspondence with this value Shutter ON OFF To select the auto electrical shutter on off Shutter Value 1 1 1 10000 To selec
11. Speed Dome Camera Introduction Manual 2 1 Introduction Features Product and Accessories CoO gt A 2 Installation Guide Preparations 9 Installation Method 10 Installation Dimensions 10 3 Dome Setting DIP Switch Setup 14 Cabling 15 Check points before operation 17 Start OSD Menu 18 Reserved Preset 18 OSD Display of Main Screen 19 4 How to use OSD Menu Main Menu 20 system Information 21 Display Setup 22 IR Setup 23 Dome Setup 24 Camera Setup 29 Preset Setup 31 Swing Setup 32 Pattern Setup 33 Group Setup 34 Auto Scan Setup 35 Zones Setup 36 Timing Action Setup 37 Alarm Input Setup 38 system Initialize 39 5 Specifications Specifications 40 Optional Bracket 42 High Speed Dome Camera Introduction Manual 3 1 Camera Specifications CCD Sensor 1 4 Interline Transfer CCD Camera Support CZ36SCM COP Zoom Magnification x 36 Optical Zoom x 32 Digital Zoom Camera Support FCB EX1020 SONY Zoom Magnification x 36 Optical Zoom x 12 Digital Zoom Camera Support SCM 2270 SCM 2273 SAMSUNG Zoom Magnification x 27 Optical Zoom x 16 Digital Zoom Camera Support SCM 2370 SCM 2373 SAMSUNG Zoom Magnification x 37 Optical Zoom x 16 Digital Zoom Day amp Night Function Various Focus Mode Auto Focus Manual Focus Semi Auto Focus Independent and Simultaneous Camera Characteristic Setup in Preset operation Main Features Step less speed changes auto zoom speed matching Pan 0 01 360 S Tilt 0 01
12. current Swing data Swing Direction INVERSE NORMAL Set the current SWING scanning direction the normal or inverse End Position Setup lt END POSITION SETUP gt Run Swing Run current Swing PTZ TO SELECT OPEN ENTER CLOSE EXIT High Speed Dome Camera Introduction Manual 32 mPattern Setup lt PATTERN SETUP gt PATTERN NO 001 STATE UNDEFINED CLR PATTERN CANCEL lt EDIT PATTERN gt lt EDIT LABEL gt RUN PATTERN BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER Edit Pattern lt PATTERN EDIT gt OPEN SAVE CLOSE EXIT TIME 1605 PTZ TO SELECT OPEN ENTER CLOSE EXIT Edit Label lt EDIT LABEL gt LABEL 7277777277 BACK EXIT OPEN SAVE CLOSE EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER lt DOME SETUP gt lt PATTERN SETUP gt Pattern Number 1 4 Selects Pattern number to edit If a selected pattern number is not defined UNDEFINED will be displayed under selected pattern number Clear Pattern CANCEL OK Deletes data in current pattern Edit Pattern Move the cursor here and then Move the cursor here and then joystick to the right to enter To start pattern recording Move camera with joystick of controller or run preset function to memorize the path mostly curve path ina selected pattern Maximum 500 commands can be stored in a pattern Edit Label Edits Label to show on monitor when preset runs MAX 10 alphabets are allowed Enter
13. edit label cursor will be displayed on the screen using left right of joystick to select character and using up down to move cursor After inputting press OPEN key to save and exit the setting Run Pattern Run current Pattern High Speed Dome Camera Introduction Manual 33 mGroup Setup lt MOTION SETUP2 GROUP SETUP gt Group Number 1 8 lt GROUP SETUP GROUP NO 001 Selects Group number to edit If a selected Group number is STATE UNDEFINED not defined UNDEFINED will be displayed under selected CLEAR GROUP CANCEL lt EDIT GROUP Group number lt EDIT LABEL gt RUN GROUP BACK Clear Group CANCEL OK EXIT Deletes data in current Group UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER Edit Group 1 Press OPEN key to start Tour setup 2 Note that MAX 16 Presets are allowed in a Tour Edit Group lt EDIT GROUP gt ID PRESET SPEED TIME I ee 350 0045 Move cursor up down and press OPEN key to set up 000 350 0045 l l l l l ooo 350 0045 3 Set up Action Dwell time and Speed is optional Time _ O00 330 0045 value from displayed in reverse Move cursor Left Right 000 350 0048 350 0045 to select items and 3 sec To 60 sec Speed value from 350 0045 350 0048 NEXT PAGE move cursor Up Down to change each value 30 to 360 Move cursor Left Right to select items and UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER Edit Label Edi Edit Label Edi
14. on an unstable or improperly supported location Improperly installed product may fall causing serious injury to a child or adult and damage to the product Use only with a mounting device recommended by the manufacturer or sold with the product To insure proper mounting follow the manufacturer s instructions and use only mounting accessories recommended by manufacturer 6 Power source This product should be operated only from the type of power source indicated on the marking label Precautions Operating Before using make sure power supply and others are properly connected While operating if any abnormal condition or malfunction is observed stop using the camera immediately and then contact your local dealer Handling Do not disassemble or tamper with parts inside the camera Do not drop or subject the camera to shock and vibration as this can damage camera Care must be taken when you clean the clear dome cover Especially scratch and dust will ruin your quality of camera Installation and Storage Do not install the camera in areas of extreme temperature which exceed the allowable range Avoid installing in humid or dusty places Avoid installing in places where radiation is present Avoid installing in places where there are strong magnetic fields and electric signals Avoid installing in places where the camera would be subject to strong vibrations Never expose the camera to rain and water High
15. to the environmental illumination changes I O Functions To reject external electric noise and shock perfectly alarm sensor Input is decoupled with photo coupler Using the dry contact for alarm input and output If an external sensor is activated camera can be set to move to the corresponding Preset position Reserved Presets for Special Purpose Most camera characteristics can be set up easily and directly with reserved preset not entering into OSD menu For more information refer to Reserved Preset in this manual High Speed Dome Camera Introduction Manual 7 II Product amp Accessories 2 _ y i 15 CD66WIB 15 CD66WB Accessories Installation and Operation Manual High Speed Dome Camera Caution AC24V 3A power for 15 CD66WIB AC24V 2A power for 15 CD66WB High Speed Dome Camera Introduction Manual Q Installation Guide Preparations Basic Requirements All the electric work must be finished under the latest electric amp fire prevention law and rules and any related law and rules Please check according to the packing list if every accessory is included And also make sure the installation is operated as required Please contact us for any help during the installation Installation Space and Density Checkup Please make sure the space is big enough to install our dome And also ensure the density of the ceilings or walls to hold total weight of the dome and its acce
16. ENTER lt IR SETUP gt lt IR TIMING SETUP gt To set the start time and stop time when the infrared was set TIME mode e Start Time 18 00 e Stop Time 08 00 Some of function can be set form user such as wiper soft limit power up action privacy zone parking action north direction and the tilt angle adjustment lt DOME SETUP gt gt lt WIPER SETUP gt Enter into Wiper Setup menu Wiper SINGLE CONTINUE To select the wiper working on single or continue mode Number 1 10 To select the number of continuing wipe when it was set CONTINUE mode Reset Reset Wiper Run wiper Run the windshield wiper High Speed Dome Camera Introduction Manual 24 m Soft Limit lt SOFT LIMIT gt SOFT LIMIT lt LEFT LIMIT gt lt RIGHT LIMIT gt LIMIT DELETE BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER m Power Up Action lt PWR UP ACTION gt PWR UP ACTION NOTHING BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER lt DOME SETUP gt gt lt SOFT LIMIT gt The user can set up the soft limit to define the left and right boundaries for the pan movement Soft Limit ON OFF To set soft limit function on off Left Limit To set left limit of the soft limit function Right Limit To set right limit of the soft limit function Limit Delete OK CANCEL To delete soft limit lt DOME SETUP gt lt PWR UP ACTION gt The user can define the dome action when power
17. Installation and Operation Manual for High Speed Dome Camera VER V1 0 15 CD66WIB 15 CD66WB Please read the operation manual carefully before installing and using this unit CAUTION CAUTION To reduce the risk of electrical shock do not open covers No user serviceable parts inside Refer servicing to qualified service personal This lightning flash with arrowhead symbol is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance A AN WARNING To prevent the risk of fire or electric shock hazard do not expose this camera to rain or moisture High Speed Dome Camera Introduction Manual 1 i Important Safeguard 1 Read Instructions Read all of the safety and operating instructions before using the product 2 Retain Instructions Save these instructions for future reference 3 Attachments Accessories Do not use attachments or accessories unless recommended by the appliance manufacturer as they may cause hazards damage product and void warranty 4 Water and Moisture Do not use this product near water or moisture 5 Installation Do not place or mount this product in or
18. SET xxx When camera reach to Preset xxx RUN PATTERN x When Pattern x is in action RUN SWG x GROUP xxx When Swing is in action XXXXXX ERR xxx When undefined function is called to run The Label stored for specific Preset and Pattern and Group This information shows current state of Alarm Input Current speed dome time and date Show current speed dome internal temperature Current speed dome IR mode Show the current level of soeed dome area location Show the current zones label High Speed Dome Camera Introduction Manual 19 i General Rules of Key Operation for Menu The menu items surrounded with lt gt always has its sub menu For all menu level to go into sub menu use joystick to the right To return last level of menu by pressing BACK key To move from items to item in the menu use joystick in the Up Down To change a value of an item use Left Right of the joystick in the controller Moving the joystick via left right to modify the parameter of the camera then saving automatically Some of functions have to save the parameter by pressing OPNE key LI Main Menu System Information Display Setup IR Setup Dome Setup Camera Setup Motion Setup Alarm Setup System Initialize SPEED DOME CAMERA lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt IR SETUP lt DOME SETUP gt lt CAMERA SETUP gt lt MOTION SETUP gt lt ALARM SETUP gt lt SYSTEM INITIALIZE gt ENIT
19. T LEFT AND RIGHT TO ENTER on or off according to the brightness of the light 2 Time Infrared light setting to open according to the time 3 Camera Infrared light turned on or off which is synchronized with the camera and transferred from day and night mode 4 NEAR Forced IR light to the near beam mode 5 FAR Forced IR light to the far beam mode 6 ON Infrared light mode forced open 7 OFF Infrared light mode forced close Output Power 00 09 To select the output power of infrared Testing Time 01S 08S To select the testing time of infrared when started Illumination on 01L 0O9L To select the starting illumination of infrared when it was AUTO mode IR Switch Zoom 01X 18xX To select the times of zoom from the high beam to low beam each other Ambient light O6L To test the light of environment automatically High Speed Dome Camera Introduction Manual 93 m IR timing Setup SIR TIMING SETUP START TIME 18 00 STOP TIME 08 00 BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER II Dome Setup lt DOME SETUP gt lt WIPER SETUP gt lt SOFT LIMIT gt lt PWR UP ACTION lt PRIVACY ZONE gt lt PARKING ACTION SETUP lt SET NORTH DIRECTION lt TILT ANGLE gt lt ADVANCED BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER m Wiper Setup lt WIPER SETUP gt WIPER SINGLE NUMBER 01 RESET RUN WIPER BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO
20. accurate 360 Pan and 10 90 Tilt range auto flip without blind area Stepless speed change auto zoom speed matching Near far IR Light auto matches camera zoom in out II All weather Outdoor Design High die cast alloy aluminum construction High Precision Mould with high heat conductivity Fully enclosed isolation design for heat sink Nanometer Dustproof waterproof and fog proof lens IP66 Waterproof 3000V lightning and surge current protection Function Instructions Focus PTZ Speed Auto Match The pan tilt rotation speed could be automatically adjusted according to the focus in out which makes it much more practical for manual target tracking Power Up Action This function enables to resume the last action executed before power down Most of actions such as Preset Pattern Swing Auto scan and Group are available for this function but jog actions are not available to resume Auto Flip When the camera tilts downward and goes just beyond the vertical position the camera will rotate 180 degrees Preset Position Set up and Call Up In the Preset function the dome stores the current pan tilt angle zoom and other position parameters in its memory When necessary the dome recalls these parameters and adjusts the camera to a particular position The user can store recall and clear the presets easily and promptly by using the keyboard controller The dome can store up to 255 presets Swing Users can set up the le
21. e Camera Introduction Manual 49
22. ensor 1 input FUSE m a a e IN7 Sensor 7 input FUSE O P IN COM I o IN COM Common point for alarm IN1 IN2 IN3 IN4 IN5 IN6 IN7 Alarm input signal After open the alarm function Speed dome can detect the status of alarm automatically Alarm output Speed dome can detect the status of alarm input automatically when any alarm was triggered then alarm output must be action High Speed Dome Camera Introduction Manual 16 II Check points before operation Before power is applied please check the cables carefully The camera ID of the controller must be identical to that of the target camera The camera ID can be checked by reading DIP switch of the camera If your controller supports multi protocols the protocol must be changed to match to that of the camera If you changed camera protocol by changing DIP switch the change will be effective after you reboot the camera Since the operation method can be different for each controller available refer to the manual for your controller if camera can not be controlled properly The operation of this manual is based on the standard Pelco Controller l i Preset and pattern Function Pre Check Check how to operate preset and pattern function with controller or DVR in advance to operate camera function fully when using controller or DVR Refer to the following table when using standard Pelco R protocol controller lt Go Preset gt Press Call input
23. ent PTZ data Edit Label Edits Label to show on monitor when preset runs MAX 10 alphabets are allowed Enter edit label cursor will be displayed on the screen using left right of joystick to select character and using up down to move cursor After inputting press OPEN key to save and exit the setting High Speed Dome Camera Introduction Manual 31 aSwing Setup lt MOTION SETUP gt gt lt SWING SETUP gt Swing Number 1 8 lt SWING SETUP gt SWING NO 001 Selects Swing number to edit STATE UNDEFINED lt START POSITION gt lt END POSITION Start And End Position W 3 ae l ae ae 6S Setup the 2 position for Swing function if a selected preset is CLR SWING CANCEL SWING DIG NORMAL not defined UNDEFINED will be displayed RUN SWING BACK When swing function runs camera moves form the preset EXIT assigned as the start point to the preset assigned as the end UP AND DOWN TO SELECT point in CW Clockwise direction The camera moves from LEFT AND RIGHT TO ENTER preset assigned as the start point to preset assigned as the end point CCW Counterclockwise direction Th f h Start Position Setup en camera moves from the preset assigned as the endpoint to the preset assigned as the start point in CCW lt START POSITION SETUP Counterclockwise direction Swing Speed 03 15 Sets Swing speed rating from 03 to 15 PTZ TO SELECT OPEN ENTER CLOSE EXIT Clear Swing CANCEL OK Deletes
24. ft and right boundaries by control keyboard Then speed dome can scan between this boundary It supports up to 8 groups of scanning paths High Speed Dome Camera Introduction Manual 5 Group The preset position can be programmed to be recalled in a set of sequences This sequence can be set to let the camera scan from one position to the next in a cycle at a set speed This feature is called the auto cruise The cruise sequence and dwell time of each preset can be set It supports up to 8 cruising tracks each cruising track with 16 presets Pattern Tour Dome can memorize 160s running path or 500 programmable instructions When start pattern tour speed dome will move automatically according recorded action path It supports 4 groups of pattern tours Guard Location The dome will automatically return to preset position if there is no operation in a period of vacant time Default Action When you start up the dome camera or do not send commands over a long time the dome camera will return to its default functions which include the home place auto pan auto cruise and pattern Dome Address Setup The dome supports up to 255 addresses and the dome will only response to the instructions given to its own address Please check the ball machine code dialing switch address setting Manual Object Tracking The use can move the joystick up down left or right to track the appearing object in the screen and use the joystick to zoo
25. gt lt Call gt 193 lt Enter gt lt Call gt 194 lt Enter gt Enters into OSD menu Start the windshield wiper Open the defrosting function Close the defrosting function Runs Pattern Function 1 4 Runs Swing Function 1 8 Runs Group Function 1 8 Sets Alarm ON Sets Alarm OFF Sets Camera BLC Mode to OFF Sets Camera BLC Mode to ON Sets Camera Focus Mode to AUTO Sets Camera Focus Mode to Manual Sets Camera Focus Mode to SEMI AUTO Sets Day amp Night Mode to AUTO Sets Day amp Night Mode to NIGHT Sets Day amp Night Mode to DAY Sets OSD Display Mode to AUTO Except Privacy Mask Sets OSD Display Mode to OFF Except Privacy Mask Sets OSD Display Mode to ON Except Privacy Mask Sets all Privacy Mask Display to OFF Sets all Privacy Mask Display to ON High Speed Dome Camera Introduction Manual 18 II OSD Display of Main Screen P T Z Information Camera ID Dome Title Action Title Action Label Alarm Input Date amp Time info Temperature IR info Zones Title Zones Label Camera ID Dome Title Action Title Zones Title Action Label Zones Label Alarm Info Date amp Time Info IR info PTZ Info Temperature Current Pan Tilt angle in degree and a compass direction Current Camera ID Address Current speed dome title Following are possible Action Titles and their meaning SET PRESET xxx When Preset xxx is stored CALL PRE
26. justable ON Off 0 01 360 S Range 360 endless 0 01 120 S Range 10 90 255 Preset Preset Accuracy 0 01 Shutter G O vlolojnjtor gt A 0 2g Pe are 3 Ie le Is c aa o cs 121531512 D o 5 J 9 16 D O D Nn op ge O Qle 3 a 2 W 5 2 o slo c Is IM O 5 D O us NITIS lo IS A D 2 aS O O 5 D 5 a Q Q D a 2 Oo 2 5 gt 5 D Co D 8 auto scan tracks user defined left and right boundaries and scan Swing speen 4 Pattern each pattern 160 sec or 500 instructions G 8 cruising tracks each cruising tracks has 16 preset positions roup user defined dwell time 1 set of Pan scan can be stored This is to keep the ball machine according to the elevation angle of executive level 360 continuous rotation and speed can be adjusted Auto flip Parking action Power Up Action etc Timing actions for 7 days of programmable schedule RS 485 9600 4800 2400 Selectable or change from OSD menu Pelco D Pelco P Auto identify 8 Zone Alarm Input Yes Yes AC24V 3A AC24V 2A 230 x 371 5 H mm Weight 5Kg Operating Temp 35 C 55 C High Speed Dome Camera Introduction Manual 41 Optional Bracket gt Ceiling Bracket 15 CD03BU1 gt Pole Bracket 15 CD04BHI b Inside Corner Bracket 15 CDO6BHI gt Outside Corner Bracket 15 CDO5BHI gt 21cm Pendent Bracket 15 CD03BH1 gt 6Feet Pendent Bracket 15 CD03BH6 V 20150318 High Speed Dom
27. m in and out with auto focus Privacy Mask Protection Set black mask areas to protect the privacy zones The black privacy locations can be set and support up to 8 mask zones Timing Running Function Users can set speed dome operation task at total 6 timing areas during 7 days Coordinates and Directions Display User can define the dome s direction of due north which will help to show up the exact moving directions on screen And zone title is supported to display when the dome moves to the specified ZONE High Speed Dome Camera Introduction Manual 6 PTZ and Lens Control Zoom Control Users can control zoom by keyboard to get near or far images Focus Control The default setting is auto focus The camera will auto focus based on the center of the video display to get the clear image In some special occasions the user could do the manual focus to get the desired image effect Auto Iris Control Auto Iris is aiming to detect the environmental lights condition and adjust the iris to get the stabilized brightness of the image Auto Back Light Compensation In the highly bright background auto back light compensation is aiming to compensate the brightness of the dark object and adjust the background brightness to get a clear image Auto Manual White Balance Auto Manual WB adjust depending on the environment light changes Day and Night Switch Only for Day Nigh Camera Speed dome camera can auto switch according
28. move cursor After inputting press OPEN key to save and exit the setting High Speed Dome Camera Introduction Manual 98 i Camera Setup lt CAMERA SETUP The user can make adjustment for the cameras under this FOCUS MODE SEMIAUTO menu IRIS MODE SEMIAUTO MIRROR OFF Focus Mode AUTO MANUAL SEMIAUTO FREEZE OFF DIGITAL ZOOM OFF DAY NIGHT AUTO a SEMIAUTO Mode lt WHITE BALANCE SETUP gt lt AUTO EXPOSURE SETUP gt BACK Manual Focus mode and Auto Focus mode Manual Focus EXIT Sets camera focus mode This mode exchanges focus mode automatically between mode activates in preset operation and Auto Focus mode UP AND DOWN TO SELECT activates when jog operation Starts With Manual mode at LEFT AND RIGHT TO ENTER presets Focus data ismemorized in each preset in advance Note the above camera menu and camera calls focus data in correspondence with presets supports only SONY FCB EX1020 as soon as camera arrives at a preset IRIS Mode AUTO MANUAL SEMIAUTO MAIN SETUF si CS vei Sets camera IRIS mode WHITE BAL ATW BACKLIGHT OFF MOTION DET OFF AK Mirror V H HV OFF EXPOSURE To select the image reverse including vertical horizontal or SPECIAL RESET both 0 SIT Freeze ON OFF Note SCM 2270 amp SCM 2370 If turn on this function the screen image will be frozen until it camera set using the embedded is turned off module itself menu settings Digital Zoom ON OFF lt MENU gt
29. on PWR UP ACTION NOTHING To select activities when power up Including NOTHING A SCAN SWING1 8 GROUP1 8 PAT TER1 4 PRESET 1 8 High Speed Dome Camera Introduction Manual 25 m Privacy Zone lt PRIVACY ZONE gt MASK NO 01 STATE DISPLAY CLEAR MASK CANCEL lt EDIT MASK gt BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER Edit Mask lt EDIT MASK gt UP DOWN LEFT RIGHT MOVE TELE WIDE CHANGE WIDTH lt DOME SETUP gt lt PRIVACY ZONE gt Privacy mask allows the user to mask the privacy areas with black frame The user can set up 8 privacy masks at most Mask No 1 8 Select Mask number If the selected mask has already data camera moves as it was set Otherwise UNDEFINED will be displayed under Mask No Display ON OFF Sets if camera makes mask shows or not on images Clear Mask OK CANCEL Deletes data in the selected mask NO Edit Mask lt DOME SETUP gt gt lt PRIVACY ZONE gt gt lt EDIT MASK gt Move camera to area to mask Then the menu to adjust mask size will be displayed Adjust mask size Use joystick or arrow buttons to adjust mask size e lt gt TILT WIDE Adjusts mask width e A V FAR NEAR Adjusts mask height e pressing the OPEN key to save editing and CLOSE key will withdraw from editing High Speed Dome Camera Introduction Manual 26 m Parking Action Setup lt PARKING ACTION SETUP PARK ACTION NOTHING WAIT TIME
30. s each day with 6 timing segments When l 00 00 00 00 NOTHING 2 00 00 00 00 NOTHING 00 00 00 00 NOTHING setup motion during the defined time segment 00 00 00 00 NOTHING 00 00 00 00 NOTHING No 1 6 00 00 00 00 NOTHING DAY FRI TIMING ACTION ON OFF BACK fishing the setup the dome will do the actions according to the To display whole the six segments each day in a week Start Time UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER To set up the start time for the defined motion within this time segment Moving the cursor up down to select item and left right setting start time Stop Time To set up the stop time for the defined motion within this time segment Moving the cursor up down to select item and left right setting stop time Motion NOTHING To setup the motion that will be operated in this time segment The motionincludes NOTHING AUTOSCAN SWING1 8 GROUP1 8 PATTER1 4 PRESET1 8 e Day MON TUE WED THU FRI SAT SUN To select date of the week Timing Action ON OFF To select the timing action on off High Speed Dome Camera Introduction Manual 37 Alarm Input Setup Match the Alarm sensor input to one of Preset Positions lt ALARM SETUP gt ALARM ENABLE Home Auto Scan Group Pattern Swing If an external sensor is ALARM NO activated camera will corresponding command position when ALARM ACT RELEASE TIME this item is predefined START FAN DEFROST Alarm Enable
31. sor to Time move the joystick up or down to select the desired position about the time and then move the joystick left or right to select corresponding time e Day MON TUE WED THU FRI SAT SUN Move the cursor to Day move the joystick to select corresponding day High Speed Dome Camera Introduction Manual 21 Display Setup SDISPLAY SETUP gt CAMERA ID ON IR INFO OFF DATE TIME OFF PTZ INFO AUTO MOTION AUTO ACTION TITLE AUTO ALARM INPUT AUTO TEMPERATURE AUTO BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER High Speed Dome Camera Introduction Manual This menu defines Enable Disable of OSD display on Main screen Ifan item is set to be AUTO the item is displayed only when the value of it is changed Camera ID ON OFF IR Information ON OFF Date Time ON OFF PTZ Information ON OFF AUTO Motion ON OFF AUTO Action Title ON OFF AUTO Alarm input ON OFF AUTO Temperature ON OFF AUTO 22 IR Setup lt IR SETUP gt The user can open and close the IR LED manually and set up IR MODE the IR LED work mode under this OSD mean control the OUTPUT POWER TESTING TIME joystick left or right to set the IR mode ILLUMINATION ON IR SWITCH ZOOM IR Mode AUT O TIME CAM NEAR FAR ON OFF AMBIENT LIGHT IR TIMING SETUP gt To select the IR LED mode such as AUTO TIME CAM NEAR FAR ON OFF 1 AUTO Infrared light is automatically turned UP AND DOWN TO SELEC
32. ssories Cables Preparation Please choose the proper cable according to the transmission distance The min requirement of coaxial BNC cable is listed as follows for reference Max Distance Feet Meter RG59 U 750ft 229m RG61 U 1 000ft 305m RG11 U 1 500ft 457m Setup Dip Switch for Dome Address Please turn to Dome Address Setup for details High Speed Dome Camera Introduction Manual Q Installation Method The high speed dome could be installed in wall mount and pendant mount Wall Mount Pendant Mount Installation Dimensions Wall Mount 15 CD66WIB 15 CD66WB Drill Drawing High Speed Dome Camera Introduction Manual 10 Pendant Mount 15 CD66WIB 15 CD66WB Drill Drawing Notice The wall and ceiling must be thick enough to install the expansion and can bear 4 times the weight of the dome camera itself High Speed Dome Camera Introduction Manual 11 Wall mount Installation Procedures 1 Take out the bracket from the package as shown mark the installation hole positions on the wall referencing to the bottom of bracket 3 Take out the high speed dome and put the cables through the bracket Use M8 screws to fix the bracket and dome body 4 Use 4 pieces of M8 screw nuts with washer to fix the bracket on the wall High Speed Dome Camera Introduction Manual 12 Pendant mount Installation Procedures Notice Pendant bracket is not designed for o
33. t the shutter speed such as 1 1 1 25 1 50 1 100 1 300 1 1000 1 10000 AGC ON OFF Enhances image brightness automatically in case that luminance level of image signal is too low High Speed Dome Camera Introduction Manual 30 Motion Setup lt MOTION SETUP SPRESET SETUP gt lt SWING SETUP gt lt PATTERN SETUP gt lt GROUP SETUP gt lt AUTO SCAN gt lt ZONES SETUP gt lt TIMING ACTION gt BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER mPreset Setup lt PRESET SETUP gt PRESET NO 001 STATE UNDEFINED CLR PRSEET CANCEL CLR ALL PRESET CANCEL lt EDIT SCENE gt lt EDIT LABEL gt BACK EXIT UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER Edit Scene lt EDIT SCENE gt OPEN SAVE CLOSE EXIT PIZ TO SELECT OPEN ENTER CLOSE EXIT User can enter this menu to set the scanning function of dome like preset swing group auto scan zones and timing action lt MOTION SETUP gt lt PRESET SETUP gt Preset Number 1 255 Except 95 Ifa selected preset is already defined camera moves to pre defined position If a selected preset is not defined UNDEFINED shows on monitor Clear Preset CANCEL OK Delete current Preset data include edit label Clear all Preset CANCEL OK Delete all current Preset data include edit label Edit Scene Redefine current Preset scene position Using Joystick move camera to desired position By pressing OPEN to save curr
34. ts Label to show on monitor when preset runs MAX 10 lt EDIT LABEL gt alphabets are allowed Enter edit label cursor will be LABEL 7777777727 BACK EXIT character and using up down to move cursor After displayed on the screen using left right of joystick to select inputting press OPEN key to save and exit the setting OPEN SAVE CLOSE EXIT e Run Group Run current Group UP AND DOWN TO SELECT LEFT AND RIGHT TO ENTER High Speed Dome Camera Introduction Manual 34 mAuto Scan Setup lt MOTION SETUP gt lt AUTO SCAN gt Scan Speed 10 50 lt AUTO SCAN gt SCAN SPEED 10 Sets Pan scan speed rating from 10 to 50 lt TILT POSITION RUN SCAN BACK Tilt Position EXIT Sets Auto scan Tilt position Including the ZOOM Run Scan Run current scan Run Auto SCAN ball machine according to a preset angle UP AND DOWN TO SELECT of TILT and ZOOM 360 horizontal rotation while running LEFT AND RIGHT TO ENTER speed rating can be adjusted in 10 50 Tilt Position Setup lt TILT POSITION SETUP OPEN SAVE CLOSE EXIT High Speed Dome Camera Introduction Manual 35 mZones Setup lt MOTION SETUP gt lt ZONES SETUP gt The use can set up zone title when the camera moves to a lt ZONES SETUP gt ZONES NO defined location which will make it much easier for the user to lt LEFT LIMIT gt lt RIGHT LIMIT lt EDIT LABEL gt check the following steps to set up a zone LABEL DISPLAY
35. utdoor installation If specially required please do make sure the waterproof installation of the dome 1 Take out the bracket from the package as shown mark the installation hole positions on the ceiling referencing to the bottom of bracket i _ 2 Drill the hole and install 4 pieces of M8 expansion bolt into the hole Onll Installation Holes 3 Take out the high speed dome and put the cables through the sockets on the bottom of the pendant bracket Use M8 screws to fix the bracket and dome body 4 Use screw nuts with washer to fix the bracket on the wall High Speed Dome Camera Introduction Manual Dome Setting Before the dome is installed please finish the setup of the baud rate and dome address Set the DIP switch inside the dome body The relative DIP switch site and connecting wires are diagramed below for reference DIP Switch Setup The dip switches are under the cover as following picture SW1 Dip switch for the dome address SW2 Dip switch for the dome protocol Baud Rate Setup SW2 Set the No 5 6 dip switch for the baud rate configuration Sao o ON on o EPS Reserved 1 If you want to control using DVR or P T controller their protocol must be identical to camera Otherwise you can not control the camera 2 Ifyou changed camera protocol by changing DIP S W the change will be effective after you reboot the camera High Speed Dome Camera
Download Pdf Manuals
Related Search