Home

Manual here

1. Note 1 Allthe above parameters can only be modified when the PON ports are disabled 2 EMS software will disable all PON ports first automatically when modify the above parameters and then enable them when finished 6 3 5 ONU P2P Due to the nature of the EPON network structure the ONU device registered on the same PON port cannot communicate with each other This feature will affect some special application If the communication is required the P2P point to point function must be enabled On the P2P Configuration page user can enable or disable this function Note 1 This configuration can only be modified when the PON ports are disabled 2 When change this configuration EMS software will shutdown the PON ports first and then open them when change finished 3 According to IEEE802 3 protocol the point to point operation between ONUS of the same PON port is not supported so we do not recommend users to enable this function unless it is really needed 6 3 6 LLID 6 3 6 1 Configuring LLID Each ONU can register and get one or more LLID in EPON system We can control the number of users under each logic link by MAC restrict Click Logic Link gt Link Configuring 33 62 WDS1U2PGE or User Manual EMs Software Link Config Pon Port Id Link ID LLID MAC OnLineStatus Associated ONU I LLID MAC Entry L D imit 0 4095 Pon Port 2 2 00 1B 62 48 5 online 1256 Pon Port 2 ig E0
2. 1v Default TPID 0 FFFF Default Vlan Costo Vo VID 1 4094 ONU Port Manage ONU Bridging Mode Client TPID Hex C LAN ID Service TPID Hex Mac Address Managenent ONU ACL ONU VLAN ONU Queue Manage ONU Qos IQP Snooping IGMP Global Parameter IGMP Port Config Logic Link Link MAC Manage Block Link Manage Link SLA Add button add Translate entry Click Add to open the Add VLAN window shown as below CH Add FLAN Client TFIL Hex 8100 CHL AN IC Semice TRID Hexd 8100 SYLAN ID Click OK button after input the TPID and VID a new translate entry will be added to the VLAN Translate list Up to 8 VLAN translate entry can be set for an ONU port Delete button delete a VLAN translate entry selected in the VLAN Translate list Refresh button refresh the Port VLAN configuration Set button apply the port VLAN configuration to this ONU port Trunk Mode Trunk mode allows the port forward multiple VLANs at the same time generally used for the connection between the network equipment The method of an ONU port under trunk mode process an Ethernet packet is shown in the following table 50 62 If the packet s VID exist in the VLAN Trunk allow list or equal to yes the port default VLAN ID forward this packet otherwise discard this packet Add default VLAN Tag to this no packet and forward this packet If the packet s VID equal to the port default VID strip the VLAN Ta
3. gt MAX Allowed LLID Number Some types ONU device support multiple LLID for these types device user can configure the maximum allowed LLID number for it For OLT device one LLID is considered as a virtual ONU 37 62 ep ue WDS1U2PGE ort User Manual EMS Software gt Registered LLID Number This parameter is the LLID number registered to OLT device currently gt User Information This parameter is used for user to fill user special information for per ONU device gt Range Value This parameter is the optical link distance from OLT to ONU device measured by OLT device 7 2 3 Basic Operation Open Basic Configure page User can do Reset Default and Save operation for per ONU device through the function buttons located on this page Through the User Traffic Enable function user can enable or disable the service traffic transmission 7 3 RSTP Configure and Port Isolation Open Advanced Configure page Following is a typical figure IGMP Global Parameter IGMP Port Config RSTP The Rapid Spanning Tree Protocol RSTP guard against the formation of loops in an Ethernet network topology Packets can become caught in repeating cycles referred to as broadcast storms that needlessly consume network bandwidth and that can significantly reduce network performance The ONU RSTP function applies on ONU user ports used to prevent network loop on these ports When network loop occur Such a
4. window from Alarm menu then click Alarm Rule Configuration Following figure is a typical view EN Config Trap Rule System Trap Name Filter EFON 1974P E OH EFON 1U8P NU user port c 7 NI Power down Sale NU UNIPort Down NU UNIPort Up NU Offline NU Online ogic Link Link ogic Link Linkup NU Traffic Change ink ID Besourc NU ID Resource llegal Regist LT Tratfic Change witch Fort Tra witch Fort Lin witch Fort Linkup FF Flug out FF Flug in an Status Change ower Status Ch i IC WC Fe Lo Choose the target device type in left column such as EPON 1U OLT device Then the supported alarm items for the selected type will be shown on right part Each entry contains the alarm name severity level and filter or not Severity level is configurable and classified as Information Minor Major and Critical four levels Different level alarms will be marked with different color in alarm window Any one of the supported alarm items can be filtered out according to requirement 8 2 Alarm Query To open Alarm Query window from Alarm menu click Alarm Query Following figure is a typical view 55 62 WDS1U2PGE ort User Manual EMs Software CR Alarm Filter fx Time Clear Severity Handler Trap Object NE IP Address From Time 2015 05 03 14 40 58 End Date 2015 06 03 14 40 58 _ Days Current Time Alarm Status Sever
5. SOMEPLUG Monaruws WDS1U2PGE GE PON OLT manual V1 1 WDS1U2PGE EPON OLT Equipment User Manual EMS Software Part Version V1 1 S ODSeSrPLUG oY WDS1U2PGE GE PON OLT manual V1 1 Statement Copyright 2012 All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without the prior written consent The information in this document may be update at any time due to product versions upgrade or any other reasons Unless otherwise agreed this manual is for reference only All statements information and recommendations in this manual do not constitute the warranty of any kind express or implied Please contact your suppliers to get the latest version of this document About This Manual This document is one of the WDS1U2PGE OLT equipment user manuals The contents of this document include EMS software installation and operation guidelines Users should learn this document first when beginning to operate FD1002S OLT device The related documents for WDS1U2PGE OLT device are WDS1U2PGE OLT Device Installation User Manual WDS1U2PGE OLT CLI Operation User Manual Revision History 2015 4 1 Ct Leg ue ET 3 Table of Contents OS PAT UI EE 2 ABOUT THIS MANUAL vene 2 REVISION HISTORY Ne 2 1 1 SOFTWARE INTRODUCTION seseeesevvssvvnsvnnvvnnsennsennnvnnvvnnvnnuvnnsvnnsennsennvsnnvnnnvnnuvnnsvnnnennuenee 5 1 1 PENE NNN 5 1 2 FUNCTIONAL PEAT URES see eee 5 2 EMS SO
6. gt Port VID All ports default VLAN ID can be modified and the valid VID range is 1 to 4094 gt Nested VLAN Nested VLAN is also called QINQ When port based QINQ or protocol based QINQ is needed on one port the Nested VLAN mode should be enabled first All ports support Nested VLAN configuration gt Broadcast Multicast and Unknown Unicast Rate Limit Uplink ports support rate limit for Broadcast Multicast and Unknown Unicast traffic When one of these traffic type is limited it will be transmitted under the configured rate value The rate units are Kbps and Kpps optional 6 2 7 2 Port Status This page displays the uplink ports working status including following parameters v Plug Status SFP transceiver installed or not v Link status working speed working duplex mode flow control mode and etc Parameters displayed on this page can t be modified Following is a typical page view 28 62 4 r H Port ID Plug Status Link State Protocol StatuWork Speed Vork Duplex Work Flow cont 3 rol OLT Device t eg Y gel plugdut LinkDown inkDown mbpsl0 hal fDup ott Basic Inf ge2 plugin LinkUp linkUp mbpslG ful lDup off Rer Interf Man oe kiagtur linkDown hinkDown mbpsl0 halfDup bee User Mana ed blugout LinkDown inkDown labpsiG leut iDup oft Trunk Managm VLAN Man RSTP ONU Authori Port Mirror IGMP Snooping g Port Port Properity Port Status Refresh 6 2 8 ONU Authentication WDS1U2PGE device s
7. 11 62 e z EMS Server Program Icon ENS 5 Sr ver 8 Cie Bo EMS Client Program Icon PMS ELG ERE EMS software installed finished Note EMS can be directly startup when set up finished PC restart is not needed 3 EMS Startup 3 1 MySQL Database Startup MySQL database must be startup before EMS software Normally MySQL should has been running up when configuration wizard successfully finished Following method can be used to verify if MySQL database is already running up Right click My Computer icon select manage option and then open the service window to verify if the MySQL service status is started 3 2 EMS Software Startup EMS software is C S structure including Server and Client two parts Server program must be started first and Client program should be run up when Server has been successfully started Double click EMS Server program icon to run it There will be a Server icon located on the program running field typically as following EMS Server Program Running Icon T rel i ER LES Note EMS Server will take several seconds normally it will not longer than 30 seconds If the program running icon cant be found there EMS Server startup failed In this condition you should check to verify if the installation requirements are satisfied and if the MySQL database is successfully configured and started After EMS Server has been started EMS Client program can be run up Client
8. Add Location Submenu Add Shortcut Icon Device Upgrade aues 01 55 35 an em 01 9E D0 MM Pork 2 Mm Pork 4 Ca location As above figure through Add Location menu or its shortcut open add location operate window as following Add Location Operation steps I Select the parent node for new added node ii Input the name of new node iii Select map for the new location node The map should be upload first when select this node on top tree the topology area will apply this map 2 Location node delete 17 62 5 2 WDS1U2PGE orr User Manual EMs Software bt mH 5 PE S ugr Pont 4 CO loca emm G AddLocation j Add Device EG Modify i Delete Change Map As above figure right click the selected location node and delete it Add Delete Device The managed element device should be added to EMS manually According to following steps to add a WDS1U2PGE OLT device to EMS 1 WDS1U2PGE device add mf Element EHanagement System System Alarm Config Performance Help leja A 03B340ONU 4 gt 03 83 40 ONLU 4 p k GA Add Location Add Location eee te Modify a AsdDevice Add Device Submenu Change Map Upload Map Add Device Shortcut Icon Device Upgrade anea 01 55 36 amea 01 96 00 A Ponkt Mmm Portz A Ca location As above figure through Add Device sub menu or its shortcut to open the device add window
9. EW Add Device Location mw px Device Type mm ie Lewice Name 192 168 120 100 TE 192 168 120 100 Read community DEE Write community So Poll Interval Sec i fs o o i Snip set Timeout 3ec 5 Snup get Timeout Sec 5 18 62 ep ue Ee ie 7 WDS1U2PGE or User Manual EMs Software As above figure the new added device need configure following parameters v Location Select the location node where the added device should be located v Device Type Select the device type for the new added device EMS can manage WDS1U2PGE OLT and other EPON products So it is needed to select correct device type Select EPON 1U type for WDS1U2PGE OLT equipment Device Alias In order to recognize the managed device easily a suitable alias is normally needed instead of IP Address or MAG Address This device alias will be displayed on top tree list IP Address Input the management IP Address of the new added element device which can be in band or out band IP Address Read and Write Community EMS software is designed based on SNMP protocol to communicate with managed devices Read and write community is used by SNMP protocol as access password Community value input here should be the same with which configured in managed device such EMS can communicate with the managed device successfully Polling Interval and SNMP Read and Write Timeout Value EMS software will poll the managed device periodically with a configured
10. Following sections introduce these ONU management features 7 2 ONU Basic Information 7 2 1 LED Indicator Usually the device panel diagram will be displayed on the ONU management window On this diagram all the working LED indicators show the actual working status See the following example figure 3 2 1 gt 321 LNK ei eu Oo EJ LNKIACT PWR o OPTIN 4 1j R LILL The bright green icon indicates light ON and the dark LED icon indicates light OFF 7 2 2 Basic Information Open Basic Configure page the ONU basic information is displayed on this page On this page user can view device type MAC Address ONU ID Number Device SN Hardware Revision Firmware Version User Information Max Allowed LLID Number Online Status and Range Value etc Following are explanations for some special parameters gt ONU ID ONU ID is the ONU device ID number which is assigned by OLT device ONU ID is convent for user to identify per ONU device ONU ID is a unique value for per PON port the range is 1 to 64 When an ONU device registered to a PON port OLT assigned an unused ONU ID value for it This value will be bound with the ONU s MAC Address until the ONU device is deleted from this PON port can only be deleted when offline When an ONU device is deleted from one PON port the ONU ID value assigned for it will be taken back When the deleted ONU registered to this PON port again it will be assigned a random new ONU ID value
11. In order to avoid upgrade an error file to target devices CRC check function can be used Before downloading file to devices the Calculate CRC tool button can be used to calculate the CRC result of the selected file When the file is transmitted to target device the device firmware will recalculate the CRC result and then compare this result with the CRC value received from EMS Such feature will avoid error file is upgraded to device 4 Upgrade Operation When the upper needed upgrade configurations are finished according to following steps to finish device upgrade procedure 1 Click Download to Device button In this step the FTP client program running on device will download the target file from the specified FTP server When finished successfully the Progress Status will display transmit ok result 2 Click Upgrade button In this step the target device will update the specified file with the new received file When finished successfully the Process Status will display upgrade ok result 3 Click Reboot button The new upgrade file will take effect when the target device reboot Whole upgrade process finished when the target device boot up with the upgraded new files 61 62 RER Ee ka BR H Le CON WDS1U2PGE OLT User Manual EMS Software End Thanks for choosing the wodaplug com products Contact Company Address Prague 150 00 Prague 5 Radlicka 33 Tomorrow systems s r o Tel 420 257 2
12. 54 H ALARM MANAGEMENT ivcssissscscccccsccesscaccssscscccccsssscscectesssscescensnesccetessssccesccedoedecetersdseessceessese 54 8 1 ALARM RULE CONFIGURATION cccecececsceccecececececcecececececcecececeaescecececeacecececeasecececeusaceceeeeececeeeeeass 55 8 2 PARTA MER EE EE EE ER EE EE 55 9 OPERATION LOG MANAGEMENT eeseevnsevnvvvnsvnnvvnnvvnnvvnnvvnnvvnnvnnsvnnnvnnvvnnvvnnvvnnvnnnvnnnvnnueeeee 57 10 DATABASE MAINTENANCE eeosvsevvnevnnvnnvvnvvnnvnnvnnvvnnvnnvnnvvnnvnnvnnvnnnvnnvnnvnnnvnnvnnunnuvnnennennnen 57 11 USER ACCOUNTS MANAGEMENT eeeseeveevnvvnnvnnvvnvvnnvnnvvnvvnnvnnvnnnvnnvnnvnnnvnnvnnvnnnvnnennennnen 58 12 SYSTEM UPGRADE EE 59 END 62 4 62 ep ue EEE a WDS1U2PGE or User Manual EMS Software 1 1 Software Introduction 1 1 Brief Views EMS Element Management System software is a C S architecture integrated device management platform which is designed based on SNMP protocol Now it is mainly used for managing EPON series products EMS need following runtime environment gt OS Windows2000 Windows XP Windows NT Windows 7 Windows8 gt Hardware CPU 2 4GHz 512M memory gt Software JAVA 1 5 MySql 5 0 1 2 Functional Features EMS software has following main features gt Based on standard SNMP protocol Support multiple client access C S architecture Support integrated management all our EPON series products Support auto topology or modify manually and multi layer map view Support configurati
13. Ge Port Ingress Policy Pon Port Input Rate Limit disable ONU 00 00 0 Upstream Peak Information Rate 0 1024000 Kbps Basic Configure Advanced Configure ONU Port Manage ONU Bridging Mode Mac Address Management ONU ACL Port Egress Shape ONU VLAN Output Rate Limit disable ONU Queue Manage E GE ONU Qos Downstream Peak Information Rate 0 1024000 Kbps IGP Snooping IGMP Global Parameter IGMP Port Config Logic Link Link MAC Manage Block Link Manage Link SLA Ingress policy feature supports to configure the maximum data rate received on 41 62 ep ue Ee ie 7 WDS1U2PGE or User Manual EMs Software each user port based on selected packet type The packet types to apply ingress policy feature can be broadcast packet multicast packet all packets and broadcast multicast DLF packets The rate unit is kbps and maximum value is 100000kbps The ingress policy feature can be disabled Egress shaping feature supports to configure the maximum output data rate on each user port And the rate limit mechanism can be weight fair or strict priority 7 5 ONU Loopback Test Loopback test function is used for network manager to test network performance between OLT and ONU equipment When do loopback test operation test packets are sent to target ONU device from OLT PON port and then these test packets are looped back to OLT PON port by the ONU device OLT software will compare the received test packets with the
14. Log Management Operation log query feature is designed for network manager to trace back the history operation records when needed From Alarm menu click System Log to open operation log management window Typical window view is shown below Filter UserName og DateTime j 2015 06 03 08 4 2015 06 03 08 4 lad From Time 2015 06 03 06 44 50 ladmin End Date 2015 06 03 09 44 50 User name ALL e Page record 50 search Sav L Current Page 1 1 History operation log can be filter out by operation user name and operation time range The query result can be saved as a excel file 10 Database Maintenance EMS database maintenance feature includes database backup and restore two functions Most of the configuration information for EMS software such as added device and location node device name and user name etc are saved in software database To avoid configuration loss when system halted network manager need to backup database constantly The backup database can be restored to retrieve the Original configuration when needed such as operating system reinstalled or EMS reinstall Database maintenance function located on System menu Click Database Backup in Database Maintenance submenu When backup operation finished following prompt message will appear Software save database files using automatically generated file name And the backup database files are saved at system defaul
15. No Add default VLAN Tag to this packet and forward If the VID is not equal to the port s default VLAN ID discard this Tag of this packet and forward Discard this packet The following figure shows the Tag VLAN configuration Page 48 62 WDS1U2PGE or User Manual EMs Software Default TPID O FFFF Refresh button refresh the Port VLAN configuration Set button apply the port VLAN configuration to this ONU port Translate Mode Translate mode allows the port overwrites VLAN tag The method of an ONU port under trunk mode process an Ethernet packet is shown in the following table If the VID of a packet equal to the CVLAN ID of a certain translation entry overwrite the packet s VID with this entry s SVLAN ID and yee forward this packet If the VID of a packet is not equal to any translation entry s CVLAN ID discard this packet Add default VLAN Tag to this no packet and forward this packet If the VID of a packet equal to the SVLAN ID of a certain translation entry overwrite the packet s VID with this entry s CVLAN ID and Downstream JER forward this packet If the VID of a packet is not equal to any translation entry s SVLAN ID discard this packet 49 62 ep ue Ee ie 7 WDS1U2PGE or User Manual EMs Software The following figure shows the Translate VLAN configuration Page OLT Device test equ Le b Pon Card Pon Module w Pon Port Port 2 iv I VLAN Mode 00 00 0
16. Size The maximum allowed burst frame length on this Logical Link The valid range is 1 to 256 unit is Kbytes The default value is 100 The default value is recommended Note 1 User can also view or modify the SLA configurations on Logical Link Link SLA page on ONU Management window They have the same configuration results 2 It is convenient to modify the configurations on ONU management page for per ONU device and have a whole view on PON card management page 7 ONU Management 7 1 ONU Management Introduction ONU is the user end device in EPON system EMS software manages the accessed ONU devices through their registered OLT device OLT device transmits 35 62 ep ue Ee ie 7 WDS1U2PGE or User Manual EMs Software management operations received from EMS software to accessed ONUs through OAM frames defined based on IEEE802 3ah standard EMS software supports to manage various tyoes ONU devices such as 1FE port type 4FE port type 4FE 2POTS type and 4FE 2POTS 1CATV type etc as long as these ONU devices support standard OAM features This part introduces the management operations for EMS software to manage 4FE port type ONU device For other types the mainly operations are the same and different management features are introduced in their special sections Double click the selected ONU device icon on topology tree list to open ONU Management window The function pages located on this windo
17. To Onu Logic Link Link Config Link SLA Refresh First As above figure SLA configurations for each PON port Logical Link ID and Direction are listed in the SLA Configuration table Logical Link ID is assigned 34 62 ep ue EN WDS1U2PGE ort User Manual EMS Software by OLT device when ONU registered to it SLA parameters are introduced as following gt Minimum Guaranteed Bandwidth Also called assured bandwidth is the bandwidth that OLT will allocate to this Logical Link assuredly The valid value range is 0 to 1000000 unit is kbps The default value is 0 Note Total minimum guaranteed bandwidth for all Logical Links registered to per PON port can t exceed the max throughput value Normally it is 950Mbps on downlink direction and 930Mbps on uplink direction When exceed the guaranteed bandwidth may be not effective gt Maximum Allowed Bandwidth Maximum allowed bandwidth is also called best effort bandwidth It is the maximum bandwidth that OLT can allocate to one Logical Link when there is free bandwidth The valid value range is 0 to 1000000 unit is kbps The default value is 1000000 gt Delay Sensitive This parameter can be set as tolerant or sensitive The sensitive option can only be set when the maximum allowed bandwidth is equal to the minimum guaranteed bandwidth Under this configuration the Logical Link will have lower delay performance gt Max Burst
18. and Server program can run on a same computer or a different computer just need the network between them communication well Following logging window will appear after the Client software successfully started 12 62 ep ue e a a WDS1U2PGE ort User Manual EMs Software See gt User name Password Language O e English If Server and Client software are installed on a same computer you should just input the correct username and password If they run on different computer you need set the Server s IP Address through the Advance configuration part The typical interface is as following Login User name admin Password pe Language ODO rk e English Connection deploy Poll Server 1 427 168 10 3 Fort 8888 TimeoutiSech 5 As above Poll Server field is the IP Address e g 192 168 10 3 of the computer on which EMS Server is running The other fields Port and Timeout use the default value normally If the transmission delay between Server and Client computers is not SO good you can change the default Timeout value to a larger one Note 1 The default Poll Server IP Address value is 127 0 01 which is the Loopback Address of the local computer You need not change this value to other Address if the Client software runs on the same computer with Server software 2 The default username and password are admin and 1234 You can change them when logging in Th
19. and need to be added when need il All the information of the deleted device will also be removed from EMS lil None any configurations on the deleted device itself will be changed 6 FD1002S OLT Management 6 1 OLT Chassis Management Double click the OLT chassis icon to open the chassis management window Typically as following figure Front Panel Wi Uplink Port SFP Out band Network eet Basic Informari Uplink Port SFP OLT chassis management includes following several parts Front Panel Four uplink ports two PON port one console port one out band network management port Led Indicator located on the card panel graphic display the card s real time working Status When EMS can t connect with the OLT the windows will change to gray color Basic Information The basic information of device type SN Version Alarm Status System Description Installation location and manager contact information 20 62 oa oe com WDS1U2PGE or User Manual EMs Software 6 2 Switch and Control Card Management Double click switch and control card icon on top tree list or the card panel icon located on chassis management window to open the switch and control management window Typical as following figure Mi Control Hodule Management EE asic Information OLT Device 192 168 v Hardware Revision OLT 0 3 Software Version OLT 1 5 24 Basic Information Running Status Running Tim
20. change their TAG UNTAG mode 3 Click the Set button to apply the new VLAN partitions Delete created VLAN groups 1 Select the VLAN group entry to be deleted in VLAN Group table 2 Click Delete button to delete the selected VLAN 6 2 6 Port Mirroring Port mirroring is used on a network switch to send a copy of network packets seen on one switch port or an entire VLAN to a network monitoring connection on another switch port This is commonly used for network appliances that require monitoring of network traffic such as an intrusion detection system To use the port mirroring feature you must designate one or more source ports and one destination port The source ports are the ports whose packets are mirrored and monitored The destination port is the port where the packets from the source ports are copied and where the network analyzer is connected There can be only one destination port on the switch FD1002S switch engine support port mirroring All switch ports including uplink and downlink ports can be designated as source ports One of four uplink port can be designated as destination port Open Port Mirror page to configure port mirroring function Here are guidelines for setting the port mirroring feature 1 Select source ports More than one port can be selected as source ports You can mirror the ingress traffic egress traffic or both on the source ports Port Port6 can be source ports 26 62
21. more MAC entry from the MAC Address List table Following sections explain the several parts of authentication function Authentication Mode Three authentication modes White List Black List and Non authority are supported Non authority When this mode is chosen ONU authentication function is disabled That is OLT device will not authenticate the accessed ONU devices All accessed ONU devices can register to this OLT device This is also the default authentication mode e Black List When this mode is chosen the MAC address whose attributes are blackMAC will be considered as illegal MACs and the MAC address whose attributes are whiteMAC will be ignored The ONUs with illegal MACs will be de registered by OLT device The ONUs with MACs that are not included in the Black List can register to this OLT device normally White List When this mode is chosen the MAC address whose attributes are whiteMAC will be considered as legal MACs and the MAC address whose attributes are blackMAC will be ignored Only those ONUs with legal MAC can register to this OLT device and others will be de registered by this OLT device MAC Address List Table The MAC Address List table will be checked to judge if a MAC is legal or illegal when the authentication mode is enabled Black List mode or White List mode User can add a unique MAC Address or a MAC Address range to this table by Add oper
22. the actual network deployment This window located on the bottom of the main frame including Alarm Log and Operation Log page Alarm log page shows and records the real time alarm information including alarm object occur time and alarm content Operation log page shows and records the manager s operation records in order to trace back when needed Alarm and Log Window 4 2 Device Management Window For device management EMS is mainly through the corresponding device management window to operate Through the Configuration menu or double click the device icons located on Top tree or topology map manager can open the device management windows Following are several typical examples Device Basic Information Windows PON Card Windows Switch and Control Card Window ONU Management windows 16 62 ep ue eene er WDS1U2PGE or User Manual EMS Software 5 Management Object Add Delete 5 1 Location Add Delete For convenience of managing numerous devices divide them in different regions according to their deployed locations is normally needed According to following steps to divide management regions 1 Adda Location node on the Top tree list Showing as follow E Element Eanagement System Sec Alarm Config Performance Help 03 83 40 0NU 4 P 03 B3 40 0NU A P 40 ONL 4 p E Tree at Gg Add Loen Add Lo e ec Modify Add Device SS Delete c6 S Location Change Map El Upload Wap
23. the MySQL Database Server No other servers such as wed or mad server wi be run MySQL wil utize up to al avaiable memory Choose Developer Machine default option click Next 8 62 PLUG CON WDS1U2PGE or User Manual EMs Software ySQL Server Instance Configuration Bizard MySQL Server Instance Configuration Configure the MySQL Server 5 0 server nstance Please select the catabase usage Multifunctional Database General gurpose databases This wil optimize the server for the use of the fest barmectiona InnoDB storage engine and the high speed MyISAM storage engne Transactional Database Only Optimized for apptcation servers anc transactional wed appicatons This vel make DmoDE the main storage engine Note that the MyISAM ere can st be used Non Transactional Database Only Suited for simple web apokabons monitoring or logging apolcations AT 8s well as ensiysis programs Only the non transactional MyISAM storage argine vel be activated Choose Multifunctional Database default option to continue nstance VLontiguration MySQL Server Instance Configuration Configure the MySQL Server 0 server instance Please set the aporoxmate number of conorrenct comrectors to the server Decision Support DSS OLAP Select this option for database appicatons that wil not require high number of concurrent conrectons A number of 20 commections wt
24. 02 1d mode all received packets will be forwarded based on 802 1d standard MAC Aging Time 40 62 JORAaPLUG CON WDS1U2PGE or User Manual EMS Software MAG Aging time can be configured for per user port it is the aging time for dynamic MAG Address entries in MAG Address table The value unit is second When this value is set to 0 the learned MAG Address entries will not be aged out 7 43 MAC Address Management Open MAC Address Management page manager can view the learned dynamic MAG Address entries on each user port Click Clear button to clear ei ONU Management ga siii MITO 4 1 en Sec e3 Sp OLT Device test equ Ly 5 UNI Port ID wniPortl Refresh Pon Card pop Module jw e ONU Dynamic MAC Index ONU Dynamic MAC Address Pon Port Port 2 ONU 00 00 0 Basic Configure Advanced Configure ONU Port Manage ONU Bridging Mode Mac Address Management IGP Snooping IGMP Global Parameter IGMP Port Config Logic Link Link MAC Manage Block Link Manage Link SLA 7 4 4 Ingress Policy and Egress Shaping ONU user ports support traffic management feature on both up and down direction Upstream direction received on user port traffic supports ingress policy feature and downstream direction traffic supports egress shaping feature Open ONU Qos page typical page is shown below aA ONU Management OLT Device test equ V port ID hmiPortl Pon Card Pon Module
25. 11010 Mail info wodaplug com Web www wodaplug com 62 62
26. 67 B3 00 0 online 3 Gre Basic Information Pon Port 2 p20 E0 67 B3 00 0 es online 20 256 OLT Device test equ v Interface Information Bridge Config Onu To Onu Logic Link Link Config Link SLA Refresh Default MAC limit is 64 so each Logic Link can service to 64 user simultaneously Number of concurrent users can be configured from 0 to 4095 6 3 6 2 Configuring Logic Link SLA SLA refers to the Service Level Agreement In EPON system OLT device maintain a SLA configuration for each registered Logical Link SLA configurations include minimum guaranteed bandwidth maximum allowed bandwidth delay sensitive and maximum burst size parameters By configuring different SLA parameters EPON system can allocate different service levels for different customers based on their service demands Click Logic Link gt Link SLA E Pon Kodule Management 4 SLA Config Pon Por Link ID Direction ID MIN Guaranteed Max Allowed Ban Delay Sensitive Max Burst Size t Id Bandwidth 256 1 dwidth 256 1000 32 4095 KBytes 000000 Kbps 000 Kbps Pon P upstream 0 1000000 tolerant 100 Basic Information Pon P 7 downstream k 1000000 jtolerant 100 Interface Information Pon P 9 upstream i 000000 tolerant 100 Bridge Config Pon P 9 dovnstrean p 1000000 tolerant 100 Pon P 110 upstream d 11000000 tolerant 100 Pon P 10 dovmatrean 11000000 tolerant 100 OLT Device test equ v Onu
27. E Al program features val be installed Requires the most ask space Custom Choose which program features you want installed and where they J L wi be installed Recommended for advarced users Choose Typical setup type 6 62 PLUG CON WDS1U2PGE ort User Manual EMs Software re Beil Server 5 0 Setup Faizard Ready to Install the Program The vated i ready ta begin iratallaljan If you want to review or change any of your hatalavon settings cick Back Click Cancel me exit the wizard Setup Type Typical Oi Program Files MYSQL ysg Server 5 04 cmd install 1 ae i Click Install to begin setting up Le Sign Up Setup Fizard MySQL com Sign Up Login or creste a new MySQL com account Please log in or select the coton to create a new account Create a new free MySQL com account If you do not yet have MySQL com account select this option and complete the folowing three steps Login to MySQL com Select this option if you already have a MySQL com account Please speoty your login information below Emal address Password Carce Choose Skip Sign Up go to next step GJ mysar Server 5 0 Setup Wizard Wizard Completed Setup has finished instaling MySQL Server 5 0 Click Finish to exit the wizard Configure the MySQL Server now Use this option to generate an optmzed MySQL config file setup Wrdous Service ruing on dedicated port ard to set the pas
28. FTWARE INSTALLATION sesevvsevvnvvnvvvnvvnnvvnnvvnnvvnnvvnnvnnnvnnnvnnvnnsvnnvvnnvnnnvnnnvnnnvnnueenee 5 2 1 DATABASE INSTALLATION Gene 5 2 2 EMS SOFTWARE INSTALLATION ugeet get Eege 11 3 EMS STARTUP arne 12 3 1 MYSQL DATABASE STARTUP arrestee gc eecinaciocaanarcetesssnrtecearesstanna adalat T nian ea ene anagiied a a ORA 12 3 2 EMS SOFTWARE STARTUP ic scsssssicnsaicnennsesdnadawssuanseasianbnenesinnsaneaaadiomsuewnssmedaaanmanionwenwndeotianemmneseantewsoans 12 4 EMS SOFTWARE FRAME INTRODUCTION eeseevesvvnsvvnvvnnvvnnvvnnvvnnvvnnvnnnvvnnennsvnnsvnnsvnnennneen 14 4 1 TRENE 14 4 2 DEVICE MANAGEMENT WINDOW sicsseiiscorcirsdisrracirenreris EEN EENS e 16 5 MANAGEMENT OBJECT ADD DELETE eeeoeevnsevnnvvnnvnnvvnnvvnnvvnnvvnnvnnnvnnnvnnsvnnsvnnvvnnvvnnennnenee 17 5 1 EOC ATO NDI DELETE oreet sac ice tag tna ised ates EE OE 17 5 2 ADD DEEDS dE EE e 18 6 FD1002S OLT MANAGEMENT eeeeovevonevnnvvnnvvnnvvnnvvnnvnnnvnnnvnnvvnnnvnnvvnnvnnuvnnnvnnnvnnsvnnsvnnsvnnennnenn 20 6 1 OLT CHASSIS MANAGEMENT 20 6 2 SWITCH AND CONTROL CARD MANAGEMENT 21 6 2 1 Device Basic Information and System Configuration rrrrrnnrernnrvnnnrennnrernnrernnern 21 6 2 2 In band Network Interface Management 22 6 2 3 User Management 23 6 2 4 TN 23 6 2 5 010116 10101910 VEAN EEE EE NE 24 6 2 6 PON MINORO EEE EE NE EE ENEE 26 6 2 7 Switch Port Management 27 6 2 7 1 PNG 27 6 2 7 2 Pr NN 28 6 2 8 COI FACTS CAN E 29 6 3 PON CARD MANAGEMENT uante ad nd cue auatiat
29. GE TRUNK features v TRUNK can applied on all four uplink ports v Support t trunk group at most v Each TRUNK group support two physical ports Only support porti and port3 configured to one group port2 and port4 TRUNK configured to one group EMS Trunk management features supported in EMS are as following Trunk Table This table displays all the configured Trunk groups and their port members Trunk ID is used to identify one Trunk group uniquely Trunk Group Add Allocate an unused Trunk ID choose the port members for this group only those un allocated ports can be chosen then click Add button to create a new Trunk group The new added group and its members will be displayed in Trunk Table Trunk Group Delete Select a Trunk group entry to be deleted in Trunk Table and click Delete button to delete it Click Refresh can get the running information of TRUNK 6 2 5 Configuring VLAN VLAN Virtual Local Area Network is the standard mechanism used today to partition a single Layer 2 bridging domain into multiple separate independent bridging domains Conceptually each VLAN constitutes a bridged network VLANs provide many useful features such as Better utilization of bandwidth by reducing flooding of Broadcasts Multicasts and unknown Unicast packets to relevant ports only 24 62 ep ue eene er WDS1U2PGE or User Manual EMS Software Natural mechanism to separate traffic with different proto
30. ODAPL ue Com WDS1U2PGE or User Manual EMs Software 2 Select destination port Only one uplink port can be designated as destination port ge1 ge4 port can be destination port 6 2 7 Switch Port Management This part describes how to display and modify the switch port settings of WDS1U2PGE The switch ports of FD1002S includes 4 uplink ports ge1 ge4 and two downlink connect with PON interface ports Fout uplink ports is identified as ge1 to ge4 from uplink port 1 to 4 and two downlink ports is identified as ge5 to ge6 from downlink port 5 to 6 Open Switch and Control Card management window The Port Property page contains the port configurable parameters and the Port Status page displays the port working status parameters 6 2 7 1 Port Property Settings The port property page typical view is as following figure Ef Control Hodule Management men FON BEE Port Properties Port ID Speed C Duplex Flow Co Port Pr Port VIPort En Permit Nest VL Broadca MulticalUnknow Inhibit jonfig Config iority D 1 409 able ilter Frame T AN Enab st Rate st ate Unicas ion Rat Net Interface Manage ig 0 7 La ype le o ontro t Rate e 0 100 User Manage Control 0000 Trunk Managment e lauto lauto is e enable is E allType is el is e dis eldis e 11000000 VLAN Management ss S T l1000000 RSTP ONU Authority Port Mirror d H IGMP Snooping Config ge S1G disable 0 i fe e disable all
31. Type is e dis e idis e dis FE Port e s dis el le e is e allType dis eldis e idis eldis Port Properity Port Status d lenable isi e allType dis e dis e dis eldis o auto is e o le e dis e allType dis e dis e dis e dis e 1000000 sable 0 disa elallType dis lel isable dis e disable 1000000 la disable 1000000 d id e 1000000 The port list table on this page includes all of the six switch ports Some parameters are configurable for all ports and some other can only be configured on uplink ports The parameters displayed as gray style in this table cannot be modified Following are the parameters description gt Port Enable Uplink ports can be shut down by setting the Port Enable parameter as disable status Downlink ports can t be disabled gt Speed and Duplex The speed and duplex mode for uplink ports can be configured Speed parameter can be set as 10M 100M and 1000M in copper mode and fixed 27 62 ep ue Ee ie 7 WDS1U2PGE or User Manual EMs Software as 1000M in fiber mode Duplex mode supports Full Duplex Half Duplex and Auto Mode gt Flow Control Uplink ports Flow Control mode can be configured as enable disable or auto mode The default mode is auto mode gt Port Priority The default priority for uplink ports can be modified and the valid range is 0 to 7 The higher value has lower priority
32. WDS1U2PGE ort User Manual EMs Software 7 6 ONU IGMP Snooping IGMP snooping can passively snoop on IGMP Query Report and Leave IGMP version 2 packets transferred between IP Multicast Routers Switches and IP Multicast hosts to learn the IP Multicast group membership It checks IGMP packets passing through it picks out the group registration information and configures multicasting accordingly ONU maintains a table of relationship between a multicast MAC address and ONU ports When an ONU port receives a Host Membership Report message ONU join this port to the corresponding table entry When the ONU receive a multicast packet ONU check this table to determine which ports to forward this packet IGMP global parameters include multicast switching mode and fast leave enable The following figure shows the ONU IGMP Global Parameter Configure Page y ONU IGMP Global Parameter Config Multicast Switching Mode IGMP MLD Snooping Fast Leave Enable Enable IGP Snooping IGMP Global Parameter IGMP Port Config ONU device supports five different Multicast Switching modes gt IGMP MLD Snooping Mode This mode is IGMP Snooping and MLD dual modes gt CTC Controllable IGMP MLD Mode This mode is Host controllable mode for IPv4 and IPv6 multicast gt IGMP Snooping Mode This mode is IGMP snooping only mode gt CTC Controllable IGMP MLD Mode This mode is Host controllable mode for IPv4 multicast gt Path Th
33. a seb eaceeaaneandausenedenaawvanieunaceoacud aan 31 6 3 1 BASIC Information VICW vvss scsscoseexcecesicascucavensesiededsviandieteesdbessxvoadvaiedandesssiasdiasacdabeoavennden 31 6 3 2 os 319 G 01 15 O EEE ee ee ret eer eee eer rer ee eer eer eee ere ee eee 31 6 3 3 OLT EEE EEE 31 Leg ue ET wu e T 6 3 4 OLT Bridge Contiouraion 32 635 PP 33 6 3 6 HI EE 33 6 3 6 1 Eeg Ste Th EEE EE EEE EE 33 6 3 6 2 Fe Ag GE REE EE 34 7 ONU MANAGEMENT eerseevnsvvnvnnvvnnvvnnvvnnvvnnvnnnvnnnvnnnvnnvvnnvrnnvnnnvnnnvnnnvnnnvnnunnnvnnnvnnuvnnuennuennunenee 35 7 1 ONU MANAGEMENT INTRODUCTION 35 7 2 ONU BASIC INFORMATION eccwcscdcensencnsdnacsasaeceanansnansned doasencsadwasenbaleveesaeae a E aa 37 7 2 1 LEDI E e EEN 37 7 2 2 Basle NNN 37 7 2 3 BASIC Operation 38 7 3 RSTP CONFIGURE AND PORT ISOLATION sensnvnvnnununnnnnnnnunnnnnnnnnnunnnnnennnnnnnnnnennunnnnnenennunnnenennunnnnnenennenen 38 7 4 ONU PORT MANAGEMENT 39 7 4 1 PON Working E 39 7 4 2 eege ee e 40 7 4 3 MAC Address Management 41 7 4 4 Ingress Policy and Egress Shaping cccscccccsssccssssccsssscsessessssscsssescssescssesesssssesaees 41 7 5 NORTETT hv 42 7 6 ONUIGMP ON 43 7 7 ONTARIO eee 45 7 8 ONU VLAN CONFIGURATION sueransesvevnennenesenenannennernennenesenenannesvernennenesenevevnesenensnsenenenenennesvevnennenenent 47 7 9 ONU LOGICAL LINK MANAGEMENT 52 7 9 1 Logical Link Status Management 52 7 9 2 Logical Link MAC Address Management 53 7 9 3 Logical Link SLA Management
34. ation When do add operation Begin MAC and End MAC should be input A unique MAC will be added if the two MAC Addresses are the same When add a MAC Address range the End MAC value should be different with the Begin MAC Note that the End MAC value should be numerical larger than the Begin MAC value When add a MAC entry the blackMAC or whiteMAC attribute should be chosen to logically assign this entry to Black List table or White List table Authentication Failure ONU MAC List Table This read only table contains the illegal ONU register information when authentication function is enabled Such as the illegal ONUs MAC Address and their number of times try to register This table contents can be cleared by click Clear button 30 62 ODOPLUG EE e WDS1U2PGE or User Manual EMs Software 6 3 PON Card Management This section describes the management functions of EMS software to manage WDS1U2PGE OLT device Currently WDS1U2PGE have two PON ports Double click the PON card icons in topology tree or the PON card graphic in chassis management window to open the PON Card Management window Following is a typical page view Pon Bodule Banagencnt 4 Basic Config OLT Device CEST equ e Running Status Running Time 1 hours 20 minutes 55 seconds FirnVer Basic Information Interface Information 6 3 1 Basic Information View Open Basic Information wind
35. be assumed Online Transaction Processing OLTP Choose this option for highly concurrent applications that may have eg ane tme up to 500 active connections such s heavily badec wed servers Manual Setting Please enter the anoraxmate number of concurrent commectons Concurrent connections 15 ms Choose Decision Support DSS OLAP default option click Next Fizard Contiguration server Instance EySol MySQL Server Instance Configuration Configure the MySCi Server 5 0 server instance Please select the defauit character set Standard Character Set Makes Latni the default diarsell This Ciaracte sekis suited for English and other West European arguages Best Support for Hultlingualism Make UTFS the default character set This i the recommended character set for storing text in meny Afferent erguages Manual Selected Default Character Set Collation Please speofy the character set to use Choose Manual Selected Default Character Set Collation option and specify Character Set as utf8 type to go to next step 9 62 PLUG WDS1U2PGE or User Manual EMs Software FOOL Server Instance Configuration Fizard MySQL Server Instance Configuration Configure the SOL Server 5 0 server rstance Please set he Windows apSors V Install As Windows Service This is the recommended way to run the MySQL server on Viindows S
36. cols or departmental traffic Increased security by preventing access between VLANs For example networks with sensitive information such as marketing and finance can be separated from the rest of the network FD1002S OLT equipment switch engine is fully compliant with the IEEE802 1Q VLAN standard and has following main features v v v Support Port based VLAN and IEEE802 1Q VLAN Support full 4K VLAN group VID range 1 4095 All switch ports including uplink ports and downlink ports support VLAN partition VLAN 1 is the system reserved VLAN it includes all switch ports all ports is UNTAG mode Open VLAN Management page typically as following VLAN Enable Disable Use the VLAN Enable option manager can enable or disable VLAN feature When disabled all ports working on VLAN Unaware mode Add a new VLAN group 1 2 Set the VLAN ID Choose the port members to be assigned to this VLAN group in Egress Ports list The default TAG modes for all port members are UNTAG Mode remove the default option on the specified ports when these ports need to be configured as TAG mode Click Add button to create the new VLAN group Left VLAN Table will list all the created VLAN groups Change created VLAN groups 25 62 ep ue eene er WDS1U2PGE or User Manual EMS Software 1 Select the VLAN group entry to be changed in VLAN Group table 2 Modify the port members belong to the selected VLAN or
37. configuration only persistent after execute Save Config which in PON card basic configu Block Link Manage Link SLA Refresh Set Open Logical Link Link SLA page Typical page is shown below On this page network manager can configure SLA parameters for the Logical Links registered by this ONU device The Logical Link SLA management features here are accordant with the SLA configurations introduced in PON card management section Please refer to subsection for detail introduction 8 Alarm Management This chapter introduces EMS alarm management features EMS software receives alarm information sent from managed EPON equipments The alarm information is contained in TRAP messages based on SNMP protocol standard To receive TRAP messages sent from managed device target IP Address should be configured first The target IP Address is the PC server s IP Address on which EMS software is installed Please refer to section to learn the operations to configure these parameters EMS software supports user defined alarm rule configuration Based on defined rule alarm information can be classified or filtered Network manager can query current alarm and history alarm information occurred on managed equipments by various search conditions Following sections introduce the alarm management details 54 62 MWooarevuc com WDS1U2PGE or User Manual EMS Software 8 1 Alarm Rule Configuration To open Alarm Rule Configuration
38. e 0 hours 55 minutes 47 seconds Net Interface Manage User Manage gt Trunk Managment Console Port Speed IP Address 192 168 120 109 VLAN Management RSTP ONU Authority Port Mirror IGMP Snooping Config Trap Receiver 1 IP Address 192 168 120 165 Trap Receiver 2 IP Address 0 0 0 0 System Config Network Mask l2ss 255 255 0 Gateway 192 168 1 1 Read Community public Write Community private T Trap Receiver 3 IP Address 0 0 0 0 Trap Receiver 4 IP Address 0 0 0 0 Refresh Set Reboot Default save Following management features are contained on this window Get or set device configuration information such as IP Address Trap Receiver Address SNMP parameters etc Get or set management user information TRUNK management of switch part QINQ management of switch part VLAN management of switch ports RSTP management of switch part Port Mirror management of switch part Status and configuration of switch ports ONU Authority management Display status attribute of port Following sections in this part introduce the management features contained on the switch and control card management window 6 2 1 Device Basic Information and System Configuration Open Basic Information windows Basic Information 21 62 ep ue eene er FS WDS1U2PGE or User Manual EMS Software Include device type serial No software and hardware
39. e main software interface will appear when successfully log in The typically initial window is as following 13 62 JG eee OLD 00 Gb pl l a Lo egen 4584 By now EMS Server and Client software has been successfully start up 4 EMS Software Frame Introduction 4 1 4 1 Main Frame Overview After successfully login software comes to main frame Following is a typical appearance Mil Element Management System System Alarm Config Performance Help EE EN ee a E GE Top Tree 1ab H ees 192 168 120 100 Di ees 192 168 1 100 C di 192 168 120 109 ME switch Control Module Mh Pon Module Y rort 1 E M rort 2 BENUM 48 56 09 ONU 7 HEN 00 00 02 0NU 1 HEN 00 00 18 0NU 4 Gje ejams 192 168 120 ONU 13 ONU 4 ONU 7 Clear Severity Handler Trap Object NE IP Address Resume Time Descript Trap Log Operation log Current User admin 06 02 2015 18 06 42 admin Query success Device Top Tree gt lab gt 192 168 120 109 gt Pon Module gt Port 2 gt 48 5B 09 0NU 7 As above figure main frame contain following several parts mn ELEMENT mannen FUNCTION contain System Alarm Configure 1 Main Menu Performance and Help parts Their main features are as 14 62 Top tree Device List Topology Shortcut Bar Topology Map Window System Menu Including System Configuration MIB Bro
40. ed when the PON port is disabled gt LLID ONU Registered Number These parameters display the registered LLID number and the registered online ONU device number for per PON port OLT Bridge Configuration Open Bridge Configuration page user can modify the following bridge parameter settings CH Pon Bodule Management 4 Bridge Parameters Config OLT Device test equ Le MAC Aging Time 0 2419200 3 300 Bridge VLAN Number 64 MAC Overwrite lai sable w Discard Unknowd MAC disable Forward Tag On Simple Bridge enable v Basic Information 1 Interface Information Click set will automatically reset OLT chip ONU will be re registered under the device Bridge Config Ref Set gt MAC Aging Time 32 62 ep ue CT 7 WDS1U2PGE or User Manual EMS Software The aging time for MAC Address learned on PON ports The valid value range is 0 to 2419200 seconds When this value is 0 the MAC aging feature is disabled The default value is 300s MAC Overwrite When this function is enabled and the dynamic MAC table is full new learned MAC Address will overwrite the oldest MAC entries Discard Unknown MAC When this function is enabled the bridge engine will not forward unknown unicast packets Forward TAG Frame on Simple Bridge When this function is enabled the bridge engine will forward all tag and untagged frames When this function is disabled the bridge engine will forward only untagged frames
41. ervice Name MYSA EN Launch the MySQL Server automaticaly V iinclude Bin Directory in Windows PATH Check this opson to include the drectory containing the server dent executables in the Windows PATH variable so they can be called from the command line L lt back Iw JP can Choose Install As Windows Service option default option and Include Bin Directory in Windows PATH option Note this is not GER option click Next Beat Setver lnstance Configuration Fiind MySQL Server Instance Comtiguration Confgae ta MySOL Server 5 0 server stands Pesse sat Pe secunty optors 2 Modify Security Settings 2 New root password e000 Ever the root osssword rom Cort gees Retype the passere Erable root scores fram renais racires create An Anonymous Account Ths coon wel create an anonymous account om tins server Please note that ths can lead to an esecure system Choose Modify Security Settings option and set New root password as 1234 and set it again in Confirm text field to confirm this security password This password is used by EMS software to access MySQL database and must be set correctly Then click Next to continue YSOL Server inatance Configuration Paszard MySQL Server Instance Configuration e Configure the MySQL Server 5 0 sever rstarce Ready 19 execute C Prepare comfiguration C Write configuration te J Start service Apply secunty set
42. es with conflicting actions may match the same frame In this case the action of the rule with the highest precedence lowest numerical value is applied to the frame The action from the lower precedence rule is ignored Step 4 Specify action categories When an Ethernet packet matches one or more ACL rules it will be filtered or forward according to the rule category Action categories can be forward or discard a frame set the Destination queue for a frame delete an existing VLAN tag add a new VLAN tag set VID set CoS and so on Step 5 Apply Set up the ACL rule click on the Add button to add the ACL rule to the ACL rule lists Click Delete button to delete the selected ACL rule entry Click Apply button to apply all rules in the ACL rule list to the ONU 7 8 ONU VLAN Configuration ONU supports four port VLAN modes Transparent mode Tag mode Translate mode Trunk mode These four modes are introduced as follows Transparent Mode In this mode upstream or downstream Ethernet packet received at this ONU port forward without processing The following figure shows the Transparent VLAN configuration Page 47 62 WDS1U2PGE or User Manual EMs Software Refresh button refresh the Port VLAN configuration Set button apply the port VLAN configuration to this ONU port Tag Mode The method of an ONU port under tag mode process an Ethernet packet is shown in the following table ee Discard this packet
43. g of this packet and forward this packet If the packet s VID not equal to the port default VID but exist in the yes VLAN Trunk allow list forward this Downstream packet If the packet s VID not equal to the port default VID and not exist in the VLAN Trunk allow list discard this packet Discard this packet The following figure shows the Trunk VLAN configuration Page Fen ONU Hanagement VLAN Mode Default TPID 0 FFFF Add button add allowed VLANs Click Add to open the Add VLAN window shown as below 51 62 EN Add VLAN TPIL Hex 8100 WLAN IC T Click OK button after input the TPID and VID a new entry will be added to the VLAN Trunk allow list Up to 16 allow VLAN entry can be set for this ONU port Delete button delete a VLAN entry selected in the ONU VLAN list Refresh button refresh the Port VLAN configuration Set button apply the port VLAN configuration to this ONU port 7 9 ONU Logical Link Management Based on EPON protocol standard OLT equipment will allocate one or more Logical Link for each successfully registered ONU device The Logical Link is also called LLID simply In downstream direction OLT add LLID field to the received standard Ethernet frames and then sent them to all registered ONU devices ONU device will only receive the frames with the same LLID value as the one it registered In upstream direction OLT schedule and manage upstream packets based on the Logical Links
44. ht uplink port can be used as In band management port without any special specified Now one network interface identified as viO can be used as in band network interface Manager can configure its network parameters on this page such as IP Address Subnet Mask Default Gateway and Management VLAN This network interface can also be disabled Note 1 The default configuration is enabled IP Address 192 168 1 100 Management VLAN disable VLAN 1 2 In band network IP Address can t be configured as the same network segment with the Out band IP Address 6 2 3 User Management Open User Manage page This page contains users information which is used to access the CLI management interface Note 1 The users list in this page is used to access CLI interface and not used to login EMS software 2 Now the CLI users information cannot be modified in EMS it can be done through CLI interface 6 2 4 Trunk Management WDS1U2PGE supports IEEE802 3ad Link Aggregation standard trunk protocol Trunk allows very high bandwidth interfaces to be created by bundling multiple physical links into a single logical link Traffic forwarded to the trunk interface is load balanced across the physical links thus achieving an effective bandwidth close to the aggregate bandwidth of each of the port members of the trunk group Open Trunk Management page Following figure shows a Trunk configuration example 23 62 WDS1U2P
45. ity _ Handler No Handler Network Element Page record cou LJNE Sel WW Alarms 50 Select Trap Name Select ALL Deselect All Illegal user login ONU Dar BLOCK ONU RSTP NORMAL ONU POWER DOWN ONU PORT DOWN ONU PORT UP ze Fees ET Weg ek Previous Next Current Page l l Alarm information can be queried by alarm time alarm level alarm status alarm device and alarm content The query result can be saved as a file On the Alarm Log page located on the bottom of EMS main window or open Current Alarm window current alarm information can be viewed Following figure is a typical view eee Systen Alarm Config Performance Help ejs aja E GE Top Tree la E g test equipment ME Switch Control Module dili Pon Module Y Port 1 Traps DER E S rort 2 SETTENE Clear Handler NE IP Address Time Resune Time emm geleet y Handler Trap Obj GEE 00 00 02 on BENN 00 00 18 on N Jof t A De els R J gt Clear Severity Handler Trap 0 D EN Trap Log Operation log Current User admin 06703 2015 09 38 40 admin Query Hardware Revision Software Version Running Status Running Time success Device 56 62 ep ue _ 7 7 WDS1U2PGE ort User Manual EMs Software 9 Operation
46. l up to 8 matching rules These matching rules are and relationship namely only when all the rules are established the matching condition is established A matching rule consists of the following components Matching fields A matching field is a continuous series of bits in a frame such as destination MAC address source MAC LLID Ethernet frame type VLAN ID COS priority IP protocol type L4 source port L4 destination port TOS priority source IP address destination IP address Rule operators Rule operators compare the value of rule field in the incoming frame with a specified value The result is a Boolean value either true or false 8 of the following Rule operators are supported Matching value The matching value is the value which specified by user used in the bool comparison in a clause 46 62 ep ue Ee ie 7 WDS1U2PGE or User Manual EMs Software Click the gt gt button to add the matching rule to the rules list Click the lt lt button to remove the selected rule in the rules list Step 2 specify the target port of the matching condition ACL rule can be applied to ONU PON port or UNI port If an ACL is applied to PON ports then this ACL rule take effect for downstream packets If an ACL is applied to UNI ports then this ACL rule take effect for upstream packets Step3 Specify rule precedence The defined range of precedence for user rules is from 8 13 8 has the highest precedence Two rul
47. m with a VLAN Tag so you will need to configure the multicast VLAN Tag processing mode ONU supports three different VLAN tag processing mode Not Strip VLAN Tag Strip VLAN Tag and Switch VLAN Tag gt Not Strip VLAN Tag Do not strip the VLAN Tag in the multicast stream Multicast stream sent from this port still contains a multicast VLAN Tag gt Strip VLAN Tag Strip the VLAN Tag in the multicast stream Multicast stream sent from this port does not contain a multicast VLAN Tag 44 62 ep ue e E H WDS1U2PGE or User Manual EMS Software gt Switch VLAN Tag Overwrite the VLAN Tag in the multicast packet then forward This mode configuration page as shown in the following figure es ONU Management OLT Device test equ w 4 Port ID luniPort1 Pon Card Pon Module v IGMP Groups 0 64 Pon Port Port 2 v onu 00 00 0 w Mutticast Strip Mode Config Multicast VLAN Config Basic Configure Multicast Strip Mode Switch VLAN Tag x Multicast VLANs Advanced Configure ONU Port Manage ONU Bridging Mode ress Management Multicast VLAN IPTV User VLAN Click Add button on the Multicast Strip Mode Configure panel to open the Add IGMP Multicast VLANs window as shown in the following figure EN Add IGEF Kulticast Switch YLAN Multicast vi AN Cos 0 7 oH VIDM 4095 d IPTY User WYLAN Cos o 7 oH VIDM 4095 1H Multicast VLAN parameter is used to match VLAN Tag in the multicast s
48. main procedure for device upgrading is two steps First download firmware files to target devices to be upgraded Then target device will go through the whole firmware update process according to upgrade commands received from EMS Device upgrading steps are introduced as follows 1 FTP Server Configure Install a FTP server program on the management PC if you have not Then start the FTP server There is a third party FTP server program WFTPD if EMS is fully installed Following introduce take WFTPD as a sample There may be some different if the FTP server is not WFTPD In such condition please refer to the software user manual From the Security menu of WFTPD program select Users rights item to open the user security dialog window Configure the username access password and home directory information Typical configuration window is shown below 59 62 1 2 3 User Rights Security Dialog x User Name E User admin New User Delete Change Pass Home Directory E AFTPSERVER jw Restricted to home Help For Help press F1 1 socket 0 users Wooarevuc ET FT WDS1U2PGE or User Manual EMs Software Copy the device firmware files to be update to the home directory of FTP server program EMS Upgrade Parameters Configuration From Configure menu select Device Upgrade Device upgrade window Typical view is shown as below Device Upgrade will appear j To
49. on operation on all EPON products functions Support multiple level operation authority Real time and history alarm record view search and save Operation history record trace and save Use independent database and support data backup and import Support performance monitor and traffic counters statistic Support third party database platform VV VV VV VV V V 2 EMS Software Installation EMS software installation needs two steps database installation and EMS software setup And database need to be installed before software setup 2 1 Database Installation The opened third part database software Mysql is used by EMS The Mysql setup programs provided in CD which is shipped with products can be directly used or you can download it from internet Remember 5 0 or higher version is compatible with EMS software 5 62 PLUG CON WDS1U2PGE or User Manual EMS Software According to following steps to install Mysql database fly MySQI Server 6 0 Setup Vizard Welcome to the Setup Wizard for MySQL Server 5 0 The Setup Wizard val install MySQL Server 5 0 release SO Zoe on your computer To contnue dok Next WARNING Ties program is protected Dy copyright law Click Next to continue 15 ByYSOL Server 5 0 Setup Vizard Setup Type Choose the setup type that best suits your needs Please select a setup type iypicat ms Common program features wil be nstalled Recommended for ME GY peneraluse O Complete A
50. op Module Port 2Z T ONU 00 00 0 Pon Port Basic Configure Advanced Configure ONU Port Manage ONU Bridging Mode Mac Addres ONU ACL ONU VLAN ONU Queue Manage ONU Qos 3 Management IGMP Snooping IGMP Global Parametey IGMP Port Config Logic Link Block Link Manage Link SLA d Link ID OnLine Associa LLID maj OLT Dynamic MAC tatus ted OND C Entry Dynamic MAC Address ID Limit 0 4095 9 lonline 9 256 Refresh Clear OLT Static MAC Index Static MAC Address f Refresh Refresh Add Delete On this page network manager can view or clear dynamic MAC Address entries learned on each Logical Link Can add or delete static MAC Address entries on each Logical Link Logical Link MAC Address tables are maintained on OLT device OLT forwards downstream frames based on MAC Address table 53 62 YORaPLUG com WDS1U2PGE or User Manual EMS Software 7 9 3 Logical Link SLA Management a ORU Hanagement OLT Device test equ y SLA Config Link ID Direction ID MIM Guaranteed BanMax Allowed Bandw Delay Sensitive Max Burst Size 32 Pon Card Pon Module dwidth 256 1000000idth 256 1000000 Pon Port Port Z kbps R mr upstream ONU 00 00 0 lHovnstrean lo Basic Configure Advanced Configure ONU Port Manage ONU Bridging Mode IQP Snooping IGMP Global Paramete IGMP Port Config Logic Link Link MAC Manage Link
51. ows it displays the PON Card firmware version Running Time and Running Status etc The led indicators located on the front panel graphic display the PON module s real time working status There are two LED on the left of the PON port are indicator of status of ONU connecter with the PON port 6 3 2 Basic Operation On Basic Information page user can reset the card default the card to factory configuration or save the configurations by click the corresponding operation button 6 3 3 OLT Management Open OLT Management page following is a typical page view 31 62 6 3 4 Pon Interface Basic Config Pon Port Id Pon Port l D OLT Enable enable OLT Device test equ v OLT Work State Max LLID Number 0 256 Registered LLID Number 0 OLT MAC Address 00 A1 02 01 03 40 Basic Information Interface Information Access ONU Number 0 Bridge Config Onu To Onu Logic Link Link Config Link SLA On this page user can do the following operations gt OLT Enable Disable Enable or disable the PON ports of this PON card When the PON ports are disabled all ONUs registered on this card will be de registered Note that some other configurations can only be modified when the PON ports are disabled gt Max LLID Number This parameter is the max LLID number allowed to register for per PON port One ONU device may register one or more LLID to the connected PON port This parameter can only be modifi
52. p Tree test Upgrade Configure Statusvew eee Top Tree location test equipm Ton quip FTP Configure IP 192 168 120 70 User Name admin Target ctriCardimage Ir Progress Status File Name Password admin ee me Refresh Download to Device Upgrade Reboot Upload to PC Choose the OLT device to be upgraded from the device list on the left column of window Input FTP Server IP Address User Name Password and Firmware file name on the Upgrade Configure page 4 Select the file target to be updated The supported upgrade targets may be different for different type devices For FD2000S OLT device for example the supported upgrade targets include switch and control card firmware PON card firmware PON chip firmware PON card configuration files and PON chip boot file Following take WDS1U2PGE OLT device as sample to introduce upgrade procedure 60 62 ep ue Ee ie 7 WDS1U2PGE or User Manual EMs Software From the Target dropdown list to select a target file object 5 Choose the target device object For per target file object some index parameters need to be chosen to specify the specific device object to be upgraded For example if the file target is for PON card object then PON card slot index need to be chosen One or more number index can be specified at the same time 6 CRC Check
53. packets sent from it to get the test results such as sent and received packets error packets and delay performance Network performance on the test optical link can be evaluated based on the loopback test results Open the ONU Loopback Test page Typical page is shown below ONU Management OLT Chassis test v Y Location MAC ed Frame Number 21 00000 0 e kel E Test Pon Card Pon 1 v Payload Size 46 1500 Bytes 100 VLAN Tag 0 4094 0 WE er 1 SC Ss Refresh Pon Port img 2 v Status Finished OK ammes ONU 03 83 40ONU 4 x Test Result SentFrames 0 Received Frames 0 B onfigure i ae tere ErrorFrames 0 Min Delay us 0 Wvanced Configur ONU Port Manage Max Delay us 0 Average Delay m ONU BridingMode Mac Address Management ONU Loopback Test ONU IGMP Snooping ONU ACL ONU VLAN ONU Qos Logic Link Link MAC Manage Block Link Manage Link SLA Loopback test steps are as follows 1 Before beginning loopback test test packet number frame length and VLAN TAG should be set first Set VLAN TAG as 0 indicates sent un tag frames 2 Choose loopback location MAC or PHY can be chosen This option is used to specify from which the test packets will be looped 3 Click Test button to start test 4 When test finished the test results will be shown on the result table 42 62 ep ue e a a 7
54. registered by ONU devices Open ONU Management window and go to Logical Link page to do Logical Link management Following subsections introduces the Logical Link management features 7 9 1 Logical Link Status Management Open Logical Link Status Management page Typical page is shown below 52 62 7 9 2 ect ONU Hanagement OLT Device test equ Pon Card Pon Module Pon Port Port 2 ONU 00 00 0 Basic Configure Advanced Configure ONU Port Manage ONU Bridging Mode ac Address ONU ACL U VLAN ONU Queue Manage ONU Qos IGHP Snooping Management IGMP Global Parameter IGMP Port Config Logic Link Link MAC Manage Block Link Manage Link SLA H Y Current Logic Link Link ID LLID MAC Associated LLID MAC E ONU ID ntry Limit 0 4095 256 3 E0 67 B 9 Blocked Link Table Blocked Link MAC The Current Logical Link table shows all the Logical Links registered by this ONU device Each Logical Link is identified by its MAC Address The Block and Unblock button is used to block or unblock Logical Links The Re register button is used to force a Logical Link to reregister to OLT When a Logical Link is blocked it will be deregistered and can t reregister again until it is unblocked later Logical Link MAC Address Management Open Ey ort Hanagement Logical Link Link MAC Management page typical page is shown below OLT Device test equ T Pon Card P
55. rough Mode This mode is all IGMP IPMC MLD IPv6 Multicast are passed through mode Fast Leave Enable 43 62 ep ue ET F WDS1U2PGE or User Manual EMS Software When Fast Leave is enabled forwarding of a group stops immediately upon reception of a Leave message for that group Note that this feature is only useful if it is known that exactly one device downstream of the ONU can join a group If more than one device is attached to the ONU port though a switch or hub then the first one to leave would stop traffic to both devices The following figure shows the IGMP Port Configure Page OLT Device test equ w 4 Po rt ID juniPortl Pon Card Pon Module v IGMP Groups 0 64 t Port 2 v 00 00 0 w Multicast Strip Mode Config mfig ONU Port Manage ONU Bridging Mode Mac Address Management ONU ACL ulticast Strip Mode Strip VLAN Tag ONU VLAN ONU Queue Manage ONU Qos IGMP Snooping IGMP Group is used to configure how many multicast groups this ONU port can join in Click Add button on the Multicast VLAN Configure Panel to open the Add IGMP Multicast VLANs window as shown in the following figure EN Add IGHP Multicast VLANs E Multicast YLAN Cos 0 7 oH VID1 4095 1 Enter the Cos and the VID then click OK button to add a multicast group to this ONU port after that multicast streams contains this multicast VLAN Tag will be transmitted to this port Because the port receives a multicast strea
56. rt Flow Control and Port Enable parameters can be configured on this page Port Speed and Duplex parameters can be configured only when the port is enabled and port link status is Up and Auto negotiation is disabled 7 4 2 Port Bridge Mode Open ONU Bridge Mode page Typical page is shown below Basic Configure Advanced Configure ONU Port Manage ONU Bridging Node Mac Address Management Bridge mode parameters for per ONU port can be configured on this page These parameters include MAC Limit MAC Aging Time and Forwarding Mode etc MAC Limit This parameter is used for network manager to control the maximum learned MAC Address entries When the forwarding mode is dropUntilLearned the new received packets with un learned MAC Address will be dropped when the number of learned MAC Address come to the configured MAC limit value When the forwarding mode is configured as d8021mode the new received packets will be flooded to all ports and their source MAC will not be learned when the number of learned MAC Address come to the configured MAC limit value Forwarding Mode The ONU user port forwarding mode can be configured as drop until learned mode and 802 1d mode by setting this parameter value as dropUntilLearned or d8021mode When the forwarding mode is drop until learned mode only the packets with learned source MAC Address will be forwarded the un learned packets will be dropped In 8
57. s two user ports are connected mistakenly one of them will be shutdown automatically by STP protocol 38 62 or off ep ue Ee ED PN WDS1U2PGE ort User Manual EMs Software By setting RSTP parameter enable disable RSTP function can be turned on Port Isolation For multiple user ports ONU equipments Layer 2 switch among these ports is supported usually But for most access network build based on EPON technology the communication among local users is not needed in most case The network designer can turn on or off switch capability among ONU user ports by setting Port Isolation parameter enable disable 7 4 ONU Port Management 7 4 1 This section describes the management function and parameter configuration for ONU user ports ONU user port management includes the following gt Port Working Status gt Port Bridge Mode Configuration gt Port MAC Address List gt Ingress Policy and Egress Shaping The following subsections introduce the above content Port Working Status Open ONU Port Management page Typical page is shown below Gi ONU Hanagement 4 Port Management Status UNI Port ID Link Status Speed and Duplex Working Status Flow Control Port Enable Status and User Information parameters for all user ports can be viewed on this page 39 62 ep ue e a a WDS1U2PGE ort User Manual EMs Software Port Speed and Duplex working mode User Information for per Po
58. sacrd for the root account Installation finished choose Configure the MySQL Server now option to begin database software configurations 7 62 PLUG com WDS1U2PGE or User Manual EMs Software BySQL Server Instance Configuration Fizard F Welcome to the MySQL Server Instance Configuration Wizard 1 0 8 The Configuration Wizard wil allow you to configure the MySQL Server 5 0 server instance To Continue cick Next next gt df ee Database configuration wizard startup click Next to continue ESOL Server Instance Configuration Vizard Configure the HySOL Server 5 0 server instance Dat tas ary e madian Bat do not Midi kava PTs Gli instalabon Ths vill use a general punnese configuration for the server that can be tuned manually Choose Detailed Configuration default option to go to next step EySOL Server Instance Configuration Vizard MySQL Server Instance Configuration Configure the MySQL Server 5 0 server mstence Please select a server type This val nfiuenoe memory disk and CPU usage Kat b H ha a This is a development machine and many other appkcabons vil be run on it MySQL Server should only use a minimal amount of memory Server Machine Several server applications vil be running on this machine Choose this opbon for web anpication servers MySQL wil have medium memory usage O Dedicated MySQL Server Machine This machine is Gedicated to run
59. t directory Network manager can move these files to securer location if needed When do database restore click Database Restore in Database Maintenance submenu Select the database file to be restored on the pop up window and click OK button to do restore operation Typical view is shown below 57 62 ep ue eene er F WDS1U2PGE or User Manual EMS Software Restore Database Please select the database s backup file 20121211211505 5qI 20130131220953 sql 20130205152121 sql On the pop up database restore window only the files saved at system default directory will be list If the backup files were moved to other location they must be copied to the default directory first The system default location for saving database files is EMS EMS Server backupDB directory 11 User Accounts Management EMS software supports multi user operation and set different privilege for different user to improve system security Network managers can add or delete user accounts or modify their information Following figure is a typical operation view si User Hanager BEE Account Phone Right admin admin System Admin alancui Sne ai System Admin st fest System Admin Login Mame admin Username admin Password Password Confirm Phone Right System Admin e User management operations are explained as below Adding a User To add a new user account do the following 1 Input username pass
60. time interval Normally the poll interval can use the default value SNMP read and write timeout values are the longest wait time for EMS to wait response from managed device Usually the default value is suitable Manager can also revise these values according to the real network performance situation When the above parameters are configured click OK button to finish the device add operation When success the new added device s icon will appear on top tree list and topology area Showing as following figure icon node New added device located on top tree location I Element Management System System Alarm Config Performance Help e S G atest equipment MM switch Control Module l Pon Module New added device icon located on Y rort 1 g j M rort 2 test equipment ENN 45 58 09 0NU 7 topology map HEN c 00 00 02 0NU 1 HE 00 00 18 0NU 4 Note For FD1002S OLT device only the chassis node need to be added manually other part such as equipped card and accessed ONU device need not to be added 19 62 ep ue ET F WDS1U2PGE or User Manual EMS Software These devices will be detected automatically 2 Delete WDS1U2PGE device Obsolete or unwanted device on top iree list can be deleted from EMS Right click on the selected device icon and select Delete option to delete a device Note 1 Deleted device cant be restored
61. tings Please press Execute to start the configuration Bak Execute Cara Come here MySQL database configuration wizard finished click Execute to startup 10 62 Woearvuc ee 4 7 WDS1U2PGE ort User Manual EMs Software 2 2 FOOL Server Instance Configuration Virard E He Server Inskance Configuration Configure the MySQL Server 50 server mylone e W Arie configuration Te LCGFeenn F es Hy SOU SOL Sewer Seet fl Apply security sengs Configuration le crealed Security G tt applied Press Finish to close the Wizard As above interface showing MySQL database installation configuration and startup successfully finished click Finish to complete all the installation steps EMS Software Installation EMS software can be installed when MySQL database has been successfully installed Run EMS set up program directly and then following the installation wizard to finish all the installation steps There are no special configuration options during the whole installation process The initial startup interface is as following EES InstallShield Wizard Preparing to Install EMS Setup amp preparing the InstallSheld Wizard which vil unde pou through the program setup process Please war Decompressing EMS mei After EMS has been successfully installed there will be two program icons created on the desktop and the installation directory Typically as following appearance
62. treams When the VLAN Tag of the multicast streams is equal to this Multicast VLAN ONU overwrite the VLAN Tag of the multicast with IPTV User VLAN then forward 7 7 ONU ACL Configuration ACL Access Control List using packet filtering read the Ethernet frame header information such as source address destination address source port destination port and so on forward or filter the packet according to the predefined rules so as to achieve the purposes of access control The following figure shows the ACL configuration Page 45 62 Ey ORT Management d AddDelete Clause OLT Device test equ v Gi Fon Card Fon Module e Field Rule false Pon Port Port 2 LS Field Select Destination MAC Field Field Field Value E Field Yalue du 00 00 0 Basic Configure Advanced Configure l ONU Port Manage ONU ACL Config ONU Bridging Mode Apply Port Entry PON Port x Prio Rule Ac Actio Field Field Field Val rity tion n Par Rule je Mac Address Management Priority 2 8 13 12 3 f J Rule Action No Operation v ONU Queue Manage ONU Qos hann Delete IGMP Snooping IGMP Global Parameter IGMP Port Config Logic Link Link MAC Manage Block Link Manage Link SLA Refresh To configure an ACL rule follow these steps Step 1 define the matching conditions A matching condition consists of one or severa
63. upports authentication feature to accessed ONU devices Authentication is based on the MAC address of ONU devices and functioned as Black list or White list table method Only one authentication mode can be chosen at the same time ONU authentication function is system level feature and the configuration applied to all PON ports of the whole device When authentication function is enabled only those authenticated ONU devices can register to OLT PON ports and others cannot register to OLT PON ports Open Switch and Control Card Management window into ONU Authentication page Following is a typical interface E Cont rol Kodule Management 4 Authentication Method Non authority w Set equ Y l MAC Address List Index MAC Address End MAC Address IMAC Attribute 1 00 00 00 11 22 33 00 00 00 11 22 33 whiteMac on Net Interface Manage User Manage Trunk Managment VLAN Management RSTP DNT Authority Port Mirror Add Delete Non Authority ONU MAC To configure the ONU authentication function perform the following procedure 1 Choose one authentication mode through the Authentication Mode dropdown list 2 Click Set button to enable the chosen mode 29 62 ep ue ET a WDS1U2PGE or User Manual EMs Software 3 Click Add button to add a MAC or a MAC range to the MAC Address List table when the authentication mode is not Non authority mode 4 Click Delete button to delete one or
64. version running status and time information System Configure Configure or check the IP Address Subnet Mask and Default Gateway Note 1 The network parameters configured here are for the out band interface of WDS1U2PGE OLT device 2 Out band IP and in band IP can t on the same network segment 3 Usually EMS will lost the connection with managed device when change the network parameters Manager should change the network parameters of the managed object in EMS to the same value with the parameters configured in the device itself to recover the connection Configure or Check SNMP Read Write Community Note 1 The Community values configured here are the parameters of the managed device itself 2 EMS should use the same Community values to access the managed device Configure or Check TRAP Receiver Address The TRAP receiver address Is the destination IP Address where device alarm information is sent When there are alarm occurred these alarm information will be sent to these configured target IP Address Usually the TRAP receivers are those computer servers on which EMS software is installed Four receiver IP Address can be configured at most 6 2 2 In band Network Interface Management Open Network Interface Management page typically as following figure ep ue _ ie 7 WDS1U2PGE ort User Manual EMs Software FD1002S supports In band and Out band two network management interfaces Any one of the eig
65. w contain all the management features for this type ONU device Following is a typical interface view for ONU management SSES OLT Device NN TC Conte ONU ID ONU Standard Pon Card Pon Module E ONU Device Type Factory Serial Pon Port Port 2 vi ONT 00 00 0 ONU User Information ONU Hardware Revision 1 0 ONU Firmware Revision O 6 0 15 0 1 0 4 ONU MAC E0 67 B3 00 00 02 Basic Configure Advanced Configure Registered LLID Num 1 ONU On Line Status ONU Port Manage l ONU Bridging Mode ONU User Traffic Enable enable LY Receiving optical power 4 49dBm Mac Address Management ONU ACL ONU VLAN 2 Sch ONU Queue Manage Refresh ul Set ONU Qos gt IGP Snooping IGMP Global Parameter IGMP Port Config Logic Link Link MAC Manage Block Link Manage Link SLA Transmitted optical power 1 47dBm ONU Range Value 16 Ometer 7 o 19 k Reboot Default Save As above figure a typical type ONU device supports following main management features ONU Basic Device Information ONU Basic Operation e RSTP Configuration ONU User Port Management e ONU Bridge Configuration e ONU MAC Address ONU Loopback Test e ONU IGMP Snooping ACL Configuration VLAN Management 36 62 ep ue e 7 7 WDS1U2PGE ort User Manual EMs Software e ONU Queue Configuration ONU Port Ingress Policing Egress Shaping ONU Logical Link SLA Configuration
66. word and other user account information on the text boxes located on the bottom of the user management window 2 Choose the operation privilege level for the adding user 58 62 ep ue TS WDS1U2PGE or User Manual EMs Software Click Adding User button icon to add this new user Click Save button icon to save the operation results Deleting a User To delete a user account do the following Choose the user account entry list in user accounts table Click Delete button icon Click Save button icon to save the results Changing User Information To change a user account configuration do the following 1 Choose the user account entry to be changed in user list table The chosen user information will be displayed on the bottom user account corresponding parameters Modify the displayed account information Click Save button icon to save the changed results User Account Privilege There are System Admin Network Manager and Common User three different management privilege levels System Admin level is the highest privilege has all the operation rights of EMS software Network Manager level has all the operation rights except of user account management function Common User level is the lowest privilege the users with this privilege can only view management information and have not the rights to do any set operations 12 System Upgrade EMS software supports device firmware on line upgrade The
67. wser Database Maintenance and User Manage etc Alarm Menu Alarm Query Configure Trap Rule and System Log are within this menu Configuration Menu Top tree update device add delete device configuration map update and device upgrade features are located in this menu Performance Menu Including performance monitor and alarm threshold configuration Help Menu Change software skin language and About information The Top tree list contains all the added and accessed devices managed by EMS Through this device list manager can view some visual device information such as online or not alarm status and location info etc Double click the device icons can navigate to their management interface window FD1002S OLT has 5 type management objects including chassis switch and control card PON card PON port and ONU device Use these buttons to manage device icons on the background map Topology Map window is the main area of EMS The topology map of managed device is displayed here For convenience of managing manager can move device icons to their installation locations which are normally matched with the background map By double click the device icons located on the map manager can open the corresponding device management window to operate In this area manager can also redraw add or delete the passive network components manually such as fiber link 15 62 and splitter device in order to make them meet with

Manual here

Contents

Download Pdf Manuals

Related Search

Related Contents