Home

monika 2 - WeChillIt.com

1. call authorized service This concerns the CAREL thermostat Thermostat displays EO or E1 or LO or HI or EE or Ed or DF instead of temperature e EO failure of temperature sensor inside the chamber call authorized service e El failure of evaporator sensor call authorized service e LO low temperature alarm lower than temperature range set within the device call authorized service e HI high temperature alarm call authorized service e EE internal defect of the regulator call authorized service e Ed max defrosting time exceeded e DF defrosting in progress this is not an alarm signal This concerns the IGLOO thermostat The device is working sound signalling is activated Make sure that e The condenser is clean if necessary clean the condenser e Condenser ventilator is working properly e Ambient temperature does not exceed 25 C The device is working too loud Make sure that e The device is standing stably e Furniture adjoining the device do not vibrate when the cooling aggregate compressor is working A Noises made by the operating device are a normal phenomenon The devices are equipped with ventilators engines and compressors which turn on and off automatically Each compressor makes certain noises when operating These sounds are made by the aggregate engine and by cooling agent flowing through the circuit This phenomenon constitutes a technical feature of coolin
2. which are not related with Monika 2 device 7 THERMOSTAT SERVICE MONIKA 2 ROTA 17 IGLOO 7 1 IGLOO thermostat 2 Gs 5 e J SC ZB WECHILLIT COM a 75 Fig 13 Igloo thermostat control panel 1 Cooling on off switch 2 Manual defrosting switch Aggregate and defrosting operating control diode 4 Temperature monitoring switch on defrosting sensor 5 Temperature regulation switch increase 6 Temperature regulation switch decrease Verification of adjusted temperature inside the device By pressing A Y switch once we can verify the adjusted temperature The adjusted temperature shall be shown on the display with a visible red blinking spot diode The preview shall finish automatically after about 3 seconds Lowering or increasing the temperature press W or A switch and the adjusted temperature shall be visible on control panel Bu pressing the W switch we decrease the temperature to the desired value The function shall end automatically after about 3 seconds Manual defrosting switch No 2 enables to initiate the defrosting cycle at any moment when the device is working regardless of the automatic defrosting function the switch shall not operate when the temperature is higher than the final defrosting temperature The user should switch on switch off the aggregate only by means
3. Fig 2 p 7 Place the device on an even and on a sufficiently hard base and then level it with the help of levelling feet Remove the protection foil from the elements of the device f ex from the inside of the device display shelves and front fender beam MONIKA 2 ROTA 5 IGLOO If the user shall obtain a device partially disassembled to secure it during transportation perform the following operations 1 Mount display shelves Fig 3 1 p 7 2 Mount glass sides Fig 4 2 1 p 8 3 Mount the aluminium lamp together with lighting on glass sides Fig 4 3 p 8 4 Mount the casing of lamp conduit Fig 4 10 p 8 Move the casing of lamp conduit to the back of the glass side in order to hide the conduit coming out of the lamp in the casing and to place it on the internal part of the glass side Mount front screen Fig 4 8 p 8 Mount front glasses of the display cabinet Fig 4 5 p 8 Mount night screens Fig 5 1 2 p 9 Place the condensate container according to Fig 6 2 p 9 does not concern devices with evaporator Clean the whole device with water of temperature not exceeding 40 C with addition of washing liquid Do not use surface scratching agents caustic agents or agents containing chlorine and or soda Do not use water stream to clean the device only a wet cloth After installing the device in the final location it should be left to rest for at least 2 hours before the
4. actuation to allow the cooling agent level to settle which will prevent from problems with actuating the cooling aggregate WARNING Protect the cooling circuit against damage Place the plug of the connecting cable directly in plug in socket it_is forbidden to connect the device by means of extension cords or dividers Power sockets optional may be used to power cash register weight and similar receivers with power not exceeding 500W Turn on the main switch Fig 7 1 p 9 which activates the temperature regulator and then aggregate of the device Set the temperature on thermostat control panel Fig 7 3 p 9 service details on p 18 or 19 Turn on the lighting switch Fig 7 2 p 9 MONIKA 2 ROTA 6 IGLOO Ae 1 2 3 II Fig 2 Removing the wooden platform Unscrew the feet from the platform 2 Remove the wooden platform 3 Screw the feet in nuts welded to the frame of the device Fig 3 Assembly of display shelves 1 Display shelf 2 Front aluminium angle section 3 Back aluminium angle section ZB N WECHILLIT COM MONIKA 2 ROTA IGLOO P v3 E J l 8 1 9 6 7 f LA u n S Li 1 d 1 Pressure of the glass glas
5. use water stream to clean the device only a wet cloth A Do not use any sharp objects to remove filth A Devices equipped with wheels cannot be used on uneven surfaces MONIKA 2 ROTA 11 IGLOO During cleaning the inside of the device do not leave the front glass freely lifted in the aluminium profile This may cause the damage of the glass and is not covered by warranty Please remove the glass with profile for the time of cleaning Fig 8 p 12 Fig 8 Front glass disassembly 1 Front glass 2 Upper aluminium profile lifted guide of the glass 3 Lower aluminium profile catch of the glass First cleaning of the device should be performed after unpacking and before actuating the device The device should be cleaned with water and neutral cleaning agents Do not use surface scratching agents caustic agents or agents containing chlorine and or soda Possible glue or silicone residues on metal elements should be removed solely with extraction naphtha does not concern elements made of plastic Do not use other organic solvents It is recommended to make a break in the exploitation of the device once a month in order to clean its interior naturally defrost the evaporator clean the condenser and verify the condition of door seals If the device is not equipped with automatic condensate evaporation it is essential to remove the condensate from the container when filling the container Fig 6 p 9
6. The number frequency of condensate removal depends on device exploitation conditions f ex air humidity door opening frequency the amount and temperature of products placed for storage ZB WECHILLIT COM MONIKA 2 ROTA 12 IGLOO Fig 9 Temperature sensor inside the device 1 Temperature sensor 2 Evaporator screen 3 Evaporator drip rail When using the display cabinet as well as during maintenance works pay attention not to destroy the temperature sensor in the evaporator screen Do not use mechanical agents in order to fasten the defrosting process It is essential to keep the condenser of the device clean Dirt may hinder the heat exchange causing mainly increase in electric energy consumption and may cause damage of aggregate compressor In order to clean the condenser it is necessary to unscrew the sheet metal screws and pull the wind brace out Clean condenser lamellas with help of soft brush or paint brush If the condenser is extremely dirty blocked lamellas it is indicated to use vacuum cleaner or compressed nitrogen to suck blow the dirt from between lamellas WECHILLIT COM A The producer shall not be held responsible for damages of the condenser aggregate resulting from non observance of condenser cleanliness MONIKA 2 ROTA 13 IGLOO Door seal should be cleaned solely with clean water without any cleansing agents and it should be thoroughl
7. WECHILLIT COM USER MANUAL COOLING DISPLAY CABINETS MONIKA 2 ROTA This sign signifies information of particular meaning for user security and for proper device exploitation IGLOO Contents 1 MOINS TEIN 3 2 PROPERTIES OF THE DEVICE oret ette eden e a eerie 3 214 PUT DOSS T TT EE 3 2 2 Description of the device 3 2 3 Technical data A Ens E ET Ra EE 4 PREPARING THE DEVICE FOR 5 3 1 Requirements concerning the place of installation 5 3 2 Connection and SOPLBIDEL iba booa AMORE OE 5 4 EXPLOITATION 10 4 1 Temperature 11 5 MAINTENANCE 11 5 1 Cleaning and maintenance VEU MuR EET 11 6 SERVICE es 14 6 1 Fault identification repair eer theo rip 14 0 2 MT 16 7 THERMOSTAT SERVICE MEE 17 Tel IGLOO 18 7 2 CAREL 18 List of figures Fie 1 Construction of the device 4 Fig 2 Removing the wooden 7 Fie gt Assembly of display shelves acne trt 7 Fig 4 Assembly of glass elements and aluminium lamp 8 Fi
8. es until the desired value shall be obtained set io press once again in order to confirm the new value of the setting point MANUAL INPUT OF THE DEFROSTING CYCLE Defrosting shall be realised in an automatic mode It is possible to force defrosting x at any moment by pressing and holding the switch for minimum 5 seconds Diode No 1 shall blink during manual defrosting ZB N WECHILLIT COM MONIKA 2 ROTA 19 IGLOO NOTE IN CASE OF NOT OBSERVING THE PRINCIPLES ON CONNECTING AND USING THE DEVICE INCLUDED IN THIS MANUAL THE PRODUCER SHALL RESERVE THE RIGHT TO RECEDE FROM OBLIGATIONS OF THE GUARANTOR Information included in this document may be altered by IGLOO without noticing the user Copying the present manual without the consent of the producer is forbidden Images and drawings are of demonstrative character and may differ from the purchased device ZB N WECHILLIT COM MONIKA 2 ROTA 20
9. g 5 Assembly disassembly of night screens 9 Fig 6 Condensate CODEALDF ses eee rini rs n ERR 9 Ino 7 Control pariel re mu qii patet R SR EDP 9 Fig 8 Front glass disassembly 12 Fig 9 Temperature sensor inside the device 13 Fig 10 Cleaning the condenser YR ER 13 Fig 11 Changing the fluorescent lamp 14 Fig 12 Data plate A 17 Fig 13 Igloo thermostat control panel 18 Fig 14 Carel thermostat control panel 19 List of tables Table 1 Technical data cesses mmm enn 5 WECHILLIT COM MONIKA 2 ROTA 2 IGLOO 1 UNLOADING The device should be transported in vertical position and it should be properly secured and packed The manufacturer ships the device on a special wooden platform secured with cardboard angle sections and foil 2 PROPERTIES OF THE DEVICE 2 1 Purpose Monika 2 is a universal cooling device used to store and display a wide assortment of grocery products in singular packages previously cooled to storage temperature Our display cabinets ensure universal and efficient display area for all types of commercial and gastronomic units Guaranteed temperature inside the display cabinet equals 2 C 8 C with ambient temperature of 15 C 25 C and relative a
10. g devices and it does not signify their faulty work Steam precipitation on glasses of the device is a normal phenomenon in case of high relative air humidity exceeding 60 and does not require calling the service 6 2 Service MONIKA 2 ROTA 16 IGLOO IGLOO service telephone number 48 014 662 19 56 or 48 605 606 071 e mail serwis igloo com pl If after checking points described in chapter 6 1 Fault identification and repair the device still does not work properly please contact Technical Service of the Igloo company stating the data from the data plate Fig 12 p 17 Serial number NS Production date Type name of the device and Date when the device was purchased Description of the problem Your exact address and telephone number with the code number The data plate is located at the back of the device in the upper right corner below the top Fig 1 18 p 4 karina WA avoeiaLOO COMPAL MEER REESE EE VE SN NS 069 XXX lt MASA 153 00 kg NAPI CIE ZNAM 230V 50Hz MOC ROZMRA ANIA 0 00 w CZYNNIK ILOSCCZYNNKA 0 00 kg ZB c ZAKRES 2 8 C KLASA URZ DZENIA 3 DATA PRODUKCJI 09 2008 GAZ SPIEN IZOLACJ 365 227 C H I L L I T Typ NAZWA URZ DZENIA Ill Il On Q 5 907759 500353 Fig 12 Data plate The above figure shows a demonstrative data plate and the data stated on the plate are exemplary data
11. ir humidity of up to 65 2 2 Description of the device Monika 2 display cabinet has static cooling All types are equipped with automatic defrosting and electronic thermostat optionally cooperating with temperature recording module enabling to record and signal too low and too high temperature within the device There is also an option with automatic condensate evaporation Monika 2 display cabinet is furnished with a storage chamber Our devices are made according to modern technologies and have all certificates required by law ZB N WECHILLIT COM MONIKA 2 ROTA 3 IGLOO 23 22 21 Fig 1 Construction of the device Shelf for handling goods on the glass 2 Bent front glass lifted 3 Glass display shelf 4 Display shelves 5 Front screen 6 Front fender beam 7 Front customer shelf 8 Illuminated front panel 9 Basis of the device 10 Aluminium lamp with illumination 11 Night screens made of plexiglas 12 Granite working top made of stainless steel or furniture board in Rota 13 Maximum loading line sticker on the glass side 14 Evaporator 15 rail condensate outflow after defrosting the evaporator 16 Storing chamber 17 Cooling aggregate 18 Data plate 19 ABS sides 20 Wooden platform fixed for transport of the device 21 Device level
12. le on the display turn on the thermostat The device is operating but the lighting is off Make sure that e Lighting switch is turned on e Fluorescent lamp or starting switch of the device are not burnt Water leakage from below the device or into the inside of the chamber Check whether the device is properly levelled e Check the patency of outflow pipes Empty the condenser tray or container Check whether there is not too much ice in the rail and on the condenser defrost when necessary The device does not reach the proper temperature the lighting is on Make sure that The main switch is on Temperature setting on the thermostat is properly set Thermostat works properly The condenser is clean if necessary clean the condenser Ambient temperature does not exceed 25 C Enough time has passed for products to be cooled Ventilation holes of the device are not blocked This concerns the IGLOO thermostat thermostat displays CO or Cl or C2 instead of displayin temperature This situation shall occur when one of temperature regulation sensors has been destroyed The following messages may be displayed in such case e CO temperature sensors inside the chamber are damaged call authorized service e C1 failure of evaporator sensor call authorized service e C2 failure of condenser alarm sensors or failure of second MONIKA 2 ROTA 15 IGLOO evaporator sensor
13. ling feet 22 Storage chamber doors 23 Wind brace when removed access to condenser lamellas 24 Control panel temperature regulator switches 2 3 Technical data MONIKA 2 ROTA 4 IGLOO Table 1 Technical data Type of the ENT Weight T OW 66 voltage curren W kWh 24h Ikg mb device ROTA kg 1 0 230 50 1 1 18 3 6 50 110 1 3 230 50 1 2 30 3 8 50 130 1 5 230 50 1 5 36 4 9 50 150 1 7 230 50 2 0 58 6 4 50 170 2 05 230 50 2 0 58 6 4 50 190 2 5 230 50 2 4 60 7 6 50 220 In devices with illuminated front panel the rated lighting power is twice bigger than the one stated in the table 3 PREPARING THE DEVICE FOR EXPLOITATION 3 1 Requirements concerning the place of installation Verify whether the cross section of feeding conduits is proper for power consumption of the installed device It is forbidden to connect the device by extension rods or dividers The device should be connected to the separate properly made electric circuit with plug in socket with protecting pin according to PBUE Regulations concerning Electric Equipment Construction The device may be actuated solely after confirmation of the fire protection efficiency with results of measures performed according to binding regulations 3 2 Connection and actuation Unpack the device and remove the wooden platform from the basis
14. not use electric devices inside grocery product storing chamber MONIKA 2 ROTA 10 IGLOO e After closing the door of the device it is not recommended to open it with force Negative pressure created inside the device is levelled within 1 2 minutes which allows easy opening of the door e Avoid unnecessary opening of doors and leaving them open for a longer period of time 4 1 Temperature regulation A Service of Igloo and thermostat temperature regulators is described in chapter 7 p Btad Nie zdefiniowano zaktadki and 19 The basic aim of a thermostat is to control the cooling aggregate to obtain the set temperature within the device and maintain it within the determined temperature ranges The producer enters all settings of temperature regulators required for normal functioning of the device Before primary actuation the user should control and possibly set the required temperature inside the device on the control panel Digital display displays the current temperature inside the device y It is forbidden to interfere with systemic parameters of the thermostat as this can lead to serious consequences including the damage of the cooling device 5 MAINTENANCE 5 1 Cleaning and maintenance All maintenance services need to be performed after disconnecting the device from power supply Protect electric installation against any damage or water spillage A Do not
15. of the main switch of the device and not by means of the direct switch on thermostat control panel Switching on the main switch shall automatically initiate the thermostat Read more on www igloo pl 7 2 CAREL thermostat MONIKA 2 ROTA 18 IGLOO EL Fig 14 Carel thermostat control panel WHAT DO DIODES ON CONTROL PANEL SIGNIFY Diode 1 is on Compressor the symbol is visible when the compressor is working It is blinking when compressor actuation is delayed by security procedure It blinks in the following cycle two blinks pause when the constant working mode is activated Diode 2 is on Ventilator the symbol is visible when evaporator ventilators are turned on It blinks when the actuation of the ventilators is delayed by external disengagement or when another procedure is in progress Diode 3 is on Defrosting the symbol is visible when the defrosting function is activated It blinks when defrosting actuation is delayed by external disengagement or when another procedure is in progress Diode 4 is on Alarm the symbol is visible when the alarm is activated 5 current temperature inside the device is displayed decimal places displayed after the comma SETTING THE DESIRED TEMPERATURE mu set press for 1 second leading value shall be displayed on the screen nd increase or decrease the leading value by means of Y and switch
16. ould be placed in a dry and well ventilated place ensuring proper air exchange distance between the wall and the device min 10 cm out of sunlight kept far from heat sources and devices enforcing air flow ceiling and portable ventilators blow in heaters The device functions properly in a room where temperature falls within appropriate climatic class stated on the data plate The operation of the device may worsen when it shall operate in temperature lower or higher than the stated temperature range VAN remarks and indications e It is necessary to properly level the display cabinet which will prevent loud operation of the device and shall ensure proper water condensate outflow during defrosting e After transporting the device wait about 2 hours before its actuation e The first filling of cooling space should be performed after its previous cooling to working temperature This principle should also be observed after longer pause in exploitation Do not block any ventilation holes which would hamper circulation of the cooled air It is also necessary to ensure proper airflow around the device aggregate ventilation holes cannot be covered e Ensure even load on shelves do not exceed their maximal load and do not exceed maximal loading e Keep the condenser clean Impurities may lead to overheating of the compressor and as a consequence may result in damage of the device which is not covered by warranty e Do
17. s side 2 Glass side 3 Aluminium lamp 4 Aluminium lamp hole plug Fig 4 Assembly of glass elements and aluminium lamp 5 Bent front glass lifted 6 Upper aluminium profile lifted guide of the glass 7 Lower aluminium profile glass catch 8 Front screen made of glass 9 Front bracket 10 Lamp conduit protection 11 Lamp conduit ZB N WECHILLIT COM MONIKA 2 ROTA IGLOO Fig 5 Assembly disassembly of night screens 1 Lower night screen shorter one mounted as the first one 2 Upper night screen longer one mounted as the second one Leaf of the aluminium lamp hides and secures the night screens before falling out 4 Night screen guide aluminium profile Fig 6 Condensate container Rail water outlet hose condensate outflow after condenser evaporation 2 Condensate container empty the condensate Fig 7 Control panel 1 Main switch turns on off the aggregate of the device 2 Lighting switch 3 Thermostat temperature regulator panel service details in Chapter No 7 p 18 and 19 MONIKA 2 ROTA 9 IGLOO 4 EXPLOITATION Temperature of the cooled space and aggregate operating cycle may fluctuate They depend on numerous factors such as amount and temperature of products placed in the device and temperature of the surroundings The device sh
18. y dried The seal cannot get into contact with oily substances or grease Control whether door close properly during maintenance procedures Test place a sheet of paper between the seal and the casing and close the door The paper should pose a tangible resistance during an attempt to pull it out 4 3 Fig 11 Changing the fluorescent lamp 1 Fluorescent lamp handle 2 Fluorescent lamp 3 Casing of fluorescent lamp and starting switch 4 Starting switch of fluorescent lamp During maintenance services it is necessary to pay attention not to damage the data place of the device Fig 12 p 17 which contains significant information for servicing organs and waste removal companies 6 SERVICE 6 1 Fault identification and repair In case of any difficulties during actuation of the device or during its exploitation please return to these chapters in this manual which explain the performed operation This aims to ensure that the device is properly operated If you still experience difficulties the following hints will help you solve the problem The device is not working Make sure that MONIKA 2 ROTA 14 IGLOO e The device is connected to the supply network e Voltage and frequency in the network are compliant with those recommended by the producer 230V 50Hz e The main switch is turned on e Thermostat is turned on This concerns the Igloo thermostat If only two spots are visib

monika 2 - WeChillIt.com

Contents

Download Pdf Manuals

Related Search

Related Contents