RokSpot RGBW Manual
Contents
1. Each receiving device typically has a means for setting the starting channel number that it will respond to For example if two 6 channel fixtures are used the first fixture might be set to start at channel 1 so it would respond to DMX channels 1 through 6 and the next fixture would be set to start at channel 7 so it would respond to channels 7 through 12 The greatest strength of the DMX communications protocol is that it is very simple and robust It involves transmitting a reset condition indicating the start of a new packet a start code and up to 512 bytes of data Data packets are transmitted continuously As soon as one packet is finished another can begin with no delay if desired usually another follows within 1 ms If nothing is changing i e no lamp levels change the same data will be sent out over and over again This is a great feature of DMX if for some reason the data is not interpreted the first time around it will be re sent shortly Not all 512 channels need to be output per packet and in fact it is very uncommon to find all 512 used The fewer channels are used the higher the refresh rate It is possible to get DMX refreshes at around 1000 times per second if only 24 channels are being trans mitted If all 512 channels are being transmitted the refresh rate is around 44 times per second In summary since its design and evolution in the 1980 s DMX has become the standard for lighting control2. Fixture Auto Shut Off Check the fan in the fixture If it is stopped or moving slower than normal the unit may have shut itself off due to high heat This is to protect the fixture from overheating Clear the fan of obstructions or return the unit for service Beam is Dim Check optical system and clean excess dust grime Also ensure that the 220V 110V switch is in the correct position if applicable No Light Output Check to ensure fixture is operating under correct mode IE sound active auto DMX Etc if applicable Chase Speed Too Fast Slow Check to ensure proper setup of speed adjustment No Power Check fuse AC cord and circuit for malfunction Blown Fuse Check AC cord and circuit for damage verify that moving parts are not restricted and that unit s ventilation is not obstructed Slow Movement Verify that 220V 110V switch is in the correct position if applicable Also check that speed channels are set appropriately No Response to Audio Verify that the fixture is in Sound Active mode Adjust Audio Sensitivity If Applicable Fixture Not Responding Responding Er raticly Make sure all connectors are seated properly and securely Use Only DMX Cables and or check cables for defects Install a Terminator Reset fixture s Intermittent Lamp Check lamp for properly installation Relamp lamp may have reached end of life Remote Doesn t Work Verify remote control cable is installed properly and sec
3. 000 lt gt 005 006 lt gt 055 056 lt gt 105 106 lt gt 155 156 lt gt 205 206 lt gt 255 32 Bit Dimmer As set in the control menu display Mode 0 8 bit 256 dimming steps Mode 1 32 bit 0 25 intensity range Mode 2 32 bit 0 50 intensity range Mode 3 32 bit 0 75 intensity range Mode 4 32 bit full intensity dimming DMX Values In Depth 8 Channel Mode Channel Value What It Does 1 000 lt gt 255 Dimmer 0 lt gt 100 2 000 lt gt 255 Red Intensity 0 lt gt 100 3 000 lt gt 255 Green Intensity 0 lt gt 100 4 000 lt gt 255 Blue Intensity 0 lt gt 100 5 000 lt gt 255 White Intensity 0 lt gt 100 6 000 lt gt 014 000 lt gt 255 Strobe Strobe Off Strobe Slow lt gt Fast 7 000 lt gt 031 032 lt gt 063 064 lt gt 095 096 lt gt 127 128 lt gt 159 160 lt gt 191 192 lt gt 223 224 lt gt 255 Fade Color Change Sound Active No Function Fade In Ch 8 Controls Speed Fade Out Ch 8 Controls Speed Fade In Fade Out Ch 8 Controls Speed Multicolor Fade Ch 8 Controls Speed Fade In Fade Out Auto Run Color Jump Ch 8 Controls Speed Sound Active Multicolor Ch 8 Controls Speed 8 0 lt gt 255 Fade Speed Fade Speed Slow lt gt Fast Page 14 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC Troubleshooting Symptom Solution
4. It is flexible robust and scalable and its ability to control everything from dimmer packs to moving lights to foggers to lasers makes it an indispensable tool for any lighting designer or lighting performer Page 16 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC Keeping Your RokSpot As Good As New The fixture you ve received is a rugged tough piece of pro lighting equip ment and as long as you take care of it it will take care of you That said like anything you ll need to take care of it if you want it to operate as designed You should absolutely keep the fixture clean especially if you are using it in an environment with a lot of dust fog haze wild animals wild teenagers or spilled drinks Cleaning the optics routinely with a suitable glass cleaner will greatly improve the quality of light output Keeping the fans free of dust and debris will keep the fixture running cool and prevent damage from overheating In transit keep the fixtures in cases You wouldn t throw a prized guitar drumset or other piece of expensive gear into a gear trailer without a case and similarly you shouldn t even think about doing it with your shiny new light fixtures Common sense and taking care of your fixtures will be the single biggest thing you can do to keep them running at peak performance and let you worry about designing a great light show putting on a great concert or maximizing your cli ent s satisfactio
5. ft The maximum recommended number of fixtures on a serial data link is 32 fixtures Data DMX Cabling To link fixtures together you ll need data cables You should use data grade cables that can carry a high quality signal and are less prone to electromagnetic interference For instance Belden 9841 meets the specifications for EIA RS 485 applications Standard microphone cables will probably be OK but note that they cannot transmit DMX data as reliably over long distanc es In any event the cable should have the following characteristics 2 conductor twisted pair plus a shield Maximum capacitance between conductors 30 pF ft Maximum capacitance between conductor amp shield 55 pF ft Maximum resistance of 20 ohms 1000 ft Nominal impedance 100 140 ohms Page 8 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC Cable Connectors Cables must have a male XLR connector on one end and a female XLR connector on the other end Duh CAUTION Do not allow contact between the common and the fix ture s chassis ground Grounding the common can cause a ground loop and your fixture may perform erratically Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other 3 Pin 5 Pin Huh If you use a controller with a 5 pin DMX output connector you will need to use a 5 pin to 3 pin adapter They are widely available ove
6. Rev A 2013 Blizzard Lighting LLC 4 OPERATING ADJUSTMENTS The Control Panel All the goodies and different modes possible with the RokSpot LED are accessed by using the control panel on the rear of the fixture There are 4 control buttons below the LED display which allow you to navigate through the various control panel menus lt MENU gt Is used to navigate to the previous higher level menu item lt UP gt Scrolls through menu items and numbers in ascending order lt DOWN gt Scrolls through menu items and numbers in descending order lt ENTER gt Is used to select and confirm store the current selection The Control Panel LED Display shows the menu items you select from the menu map on page 11 When a menu function is selected the display will show immediately the first available option for the selected menu function To select a menu item press lt ENTER gt Press the lt MENU gt button repeatedly until you reach the desired menu function Use the lt UP gt and lt DOWN gt buttons to navigate the menu options Press the lt ENTER gt button to select the menu function currently displayed or to enable a menu option To return to the previ ous option or menu without changing the value press the lt MENU gt button Page 11 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC Control Panel Menu Structure Addr d001 d512 To choose the DMX address SLAU SL AU To run the fixture in sla
7. and related stage equipment DMX provides up to 512 control channels per data link Each of these channels was origi nally intended to control lamp dimmer levels You can think of it as 512 faders on a lighting console connected to 512 light bulbs Each slider s position is sent over the data link as an 8 bit number having a value between 0 and 255 The value 0 corresponds to the light bulb being completely off while 255 corresponds to the light bulb being fully on DMX data is transmitted at 250 000 bits per second using the RS 485 transmission stan dard over two wires As with microphone cables a grounded cable shield is used to prevent interference with other signals There are five pins on a DMX connector a wire for ground cable shield two wires for Primary communication which goes from a DMX source to a DMX receiver and two wires for a Secondary communication which goes from a DMX receiver back to a DMX source Generally the Secondary channel is not used so data flows only from sources to receiv ers Hence most of us are most familiar with DMX 512 as being employer over typical 3 pin mic cables although this does not conform to the defined standard DMX is connected using a daisy chain configuration where the source connects to the input of the first device the output of the first device connects to the input of the next device and so on The standard allows for up to 32 devices on a single DMX link
8. indicated on the voltage selector switch All fixtures must be connected to circuits with a suitable Ground Earthing Getting A Hold Of Us If something is wrong just give us a call or send an email We ll be happy to help honest Blizzard Lighting N16 W23390 Stoneridge Dr Suite E Waukesha WI 53188 USA www blizzardlighting com 414 395 8365 Email support blizzardlighting com Disclaimer The information and specifications contained in this document are subject to change without notice Blizzard Lighting assumes no responsibility or liability for any errors or omissions that may appear in this user manual Blizzard Lighting reserves the right to update the existing document or to create a new document to correct any errors or omissions at any time You can download the latest version of this document from www blizzardlighting com Author Date Last Edited Date J Thomas 12 12 2013 J Thomas 12 16 2013 Page 4 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC SAFETY INSTRUCTIONS Please keep this User Guide for future use If you sell the unit to someone else be sure that they also receive this User Guide ALWAYS make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on the de cal or rear panel of the fixture This product is intended for indoor use only To prevent risk of fire or shock do not expose fi
9. Blizzard Lighting LLC www blizzardlighting com Waukesha WI USA Copyright c 2013 rokspot RGBW TM Page 2 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC TABLE OF CONTENTS RokSpot LED Pin Spot 1 1 Getting Started 3 What s In The Box 3 Getting It Out Of The Box 3 Powering Up 3 Getting A Hold Of Us 3 Safety Instructions Don t Stick Your Hand In The Toaster 4 2 Meet The RokSpot LED Pin Spot 5 Features 5 DMX Quick Reference 5 The RokSpot Pin up Picture 6 3 Setup 7 Fuse Replacement 7 Connecting A Bunch Of RokSpot Fixtures 7 Data DMX Cables 7 Cable Connectors 8 3 Pin 5 Pin Huh 8 Take It To The Next Level Setting up DMX Control 8 Fixture Linking Master Slave Mode 9 Mounting Rigging 9 4 Operating Adjustments 10 Navigating The Control Panel 10 Control Panel Menu Structure 11 DMX Mode 12 Master Slave Mode 12 Sound Active Mode 12 Standalone Program Mode 12 Manual Color Adjustment 12 DMX Channel Values In Depth 13 Troubleshooting 14 5 Appendix 15 A Quick DMX Lesson 15 Keeping Your RokSpot As Good As New 16 Returns Gasp 16 Shipping Issues 16 Tech Specs 17 Page 3 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC 1 GETTING STARTED What s In The Box 1 x RokSpot Professional LED Pin Spot 1 x Rockin Power Cord This Lovely User Manual Getting It Out Of The Box Congratulations on purchasing o
10. HE ROKSPOT LED PIN SPOT CONTROL FEATURES RGBW color mixing via 1x 15W OSRAM LED Variable electronic dimming amp strobe Built in color amp chase macros via DMX Built in automated programs via master slave Built in sound active programs RGBW color mixing ability in standalone mode HSV 3 Ch RGBW 4 Ch RGBW Dimmer 5 Ch Extended 8 Ch amp Extended 32 bit dimming 9 Ch DMX Profiles ADDITIONAL FEATURES Narrow 8 beam angle Rugged and well built It hits the gym regularly Natural convection cooling Secure bracket for positioning flexibility Flicker free constant current 400hz LED driver 3 pin male input and 3 pin female output PowerCon compatible AC power In Out connectors DMX Quick Reference 8 9 Channel Mode Channel 8 Channel 9 Channel 1 Dimmer Dimmer 2 Red Intensity Red Intensity 3 Green Intensity Green Intensity 4 Blue Intensity Blue Intensity 5 White Intensity White Intensity 6 Strobe Strobe 7 Built in Programs Built in Programs 8 Program Speed Program Speed 9 32 Bit Dimmer DMX Quick Reference 3 HSV 4 5 Channel Mode Channel HSV 4 Channel 5 Channel 1 Hue Red Intensity Dimmer 2 Saturation Green Intensity Red Intensity 3 Value Blue Intensity Green Intensity 4 White Intensity Blue Intensity 5 White Intensity Page 6 RokSpot RGBW Manual Rev A 2013 Bl
11. Press the lt MENU gt button to confirm Stand Alone Master Slave Sound Active Modes Allows a single or Master Slaved units to run factory installed programs at user selectable speeds 1 To set the fixture in Flash Fade mode select FLAS or FAdE To confirm press the lt ENTER gt button 2 Now you can adjust the flash settings from FL00 FL15 or the fade settings from FA00 FA15 Then press the lt ENTER gt button to confirm 3 To use the fixture in automatic mode select ASC and press the lt ENTER gt button Then use the lt UP DOWN gt to choose from AS00 AS15 then press the lt ENTER gt button to confirm 4 Adjust the speed of the chase as above using SP15 slowest to SP00 fastest then press the lt ENTER gt button to confirm 5 To set the fixture as a slave unit select SLAU and hit lt ENTER gt The unit will display a flashing SL AU to indicate it is in slave mode Sound Active Mode 1 To use sound active mode select SouA then press the lt ENTER gt button to confirm Standalone Program Mode Allows a single unit to display a variety of colors and programs without a DMX controller 1 To set the fixture in manual mode select Pr To confirm press the lt ENTER gt button 2 Now select the program by using the lt UP gt and lt DOWN gt buttons to select Pr00 Pr30 To confirm press the lt ENTER gt button Manual Color Adjustment Allows the user to adjust th
12. e color balance of the fixture These settings are global they will effect all modes 1 Use the lt MENU gt and lt UP DOWN gt button to select rL Red Level GL Green Level bL Blue Level or UL White Level then hit lt ENTER gt 2 Using the lt UP DOWN gt buttons select the maximum level for each color between x000 x255 000 off then hit lt ENTER gt to confirm Page 13 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC DMX Values In Depth 9 Channel Mode Channel Value What It Does 1 000 lt gt 255 Dimmer 0 lt gt 100 2 000 lt gt 255 Red Intensity 0 lt gt 100 3 000 lt gt 255 Green Intensity 0 lt gt 100 4 000 lt gt 255 Blue Intensity 0 lt gt 100 5 000 lt gt 255 White Intensity 0 lt gt 100 6 000 lt gt 014 015 lt gt 255 Strobe Dimming Strobe Slow lt gt Fast 7 000 lt gt 031 032 lt gt 063 064 lt gt 095 096 lt gt 127 128 lt gt 159 160 lt gt 191 192 lt gt 223 224 lt gt 255 Fade Color Change Sound Active No Function Fade In Ch 8 Controls Speed Fade Out Ch 8 Controls Speed Fade In Fade Out Ch 8 Controls Speed Multicolor Fade Ch 8 Controls Speed Fade In Fade Out Auto Run Color Jump Ch 8 Controls Speed Sound Active Multicolor Ch 8 Controls Speed 8 0 lt gt 255 Fade Speed Fade Speed Slow lt gt Fast 9
13. en 7 days of receipt Page 17 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC Tech Specs Weight amp Dimensions Length 5 8 inches 146 5 mm Width 5 2 inches 130 mm Height 6 7 inches 169 6 mm Weight 1 8 lbs 8 kg Power Operating Voltage 100 264VAC 47 63HZ Power Consumption 15W 2a pf 64 Light Source LED 1x 15W 4 in 1 LED 100 000 hours Optical Beam Angle 8 degree optics standard Luminous Intensity Lux m Red Green Blue White All 1m 5 640 5 950 5 300 10 150 18 680 2m 1 240 1 380 1 210 2 180 4 240 Thermal Max Operating Temp 104 degrees F 40 degrees C ambient Control Protocol USITT DMX 512 DMX Channels 3 4 5 8 9 Input 3 pin XLR Male Output 3 pin XLR Female Other Operating Modes Standalone Master Slave Sound Active Color Preset Other Information When I see hitchhikers I just pretend that they approve of my driving Warranty 2 year limited warranty does not cover malfunc tion caused by damage to LED s DISCLAIMER The power connector fitted to the fixture and fixture cord are designed for compatibility with products manufactured by Neutrik AG Neutrik USA and their related entities howev er they are not manufactured by affiliated with or endorsed by Neutrik AG Neutrik USA or any related entity Neutrik and powerCON are registered trademarks of Neutrik AG Page 18 RokSpot RGBW Manual Rev A 2013 Bl
14. from the output as stated above to the input of the following fixture and so on A quick note Often the setup for Master Slave and Standalone operation requires that the first fixture in the chain be initialized for this purpose via either settings in the control panel or DIP switches Secondarily the fixtures that follow may also re quire a slave setting Check the Operating Adjustments section in this manual for com plete instructions for this type of setup and configuration Mounting amp Rigging This fixture may be mounted in any SAFE position provided there is enough room for ventilation It is important never to obstruct the fan or vents pathway Mount the fixture using a suitable C or O type clamp The clamp should be rated to hold at least 10x the fixture s weight to ensure structural sta bility Do not mount to surfaces with unknown strength and ensure properly rated rigging is used when mounting fixutres overhead Adjust the angle of the fixture by loosening both knobs and tilting the fixture After finding the desired position retighten both knobs When selecting installation location take into consideration lamp replacement access if applicable and routine maintenance Safety cables MUST ALWAYS be used Never mount in places where the fixture will be exposed to rain high humidity extreme temperature changes or restricted ventilation Page 10 RokSpot RGBW Manual
15. izzard Lighting LLC Figure 1 The RokSpot Pin Up Picture 1x OSRAM 4 in 1 RGBW LED 4 button LED Control Panel Mounting Yoke with Adjustment Locking Knobs Figure 2 The Rear Connections DMX In DMX Out Menu Buttons Heavy Duty Cast Aluminum Enclosue AC Power Out AC Power Out Page 7 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC 3 SETUP Fuse Replacement CAUTION The RokSpot utilizes a high output switch mode power supply with an internal fuse Under normal operating conditions the fuse should not require replacement The fuse is field replaceable however it is an advanced procedure suited to qualified individuals Should your RokSpot fuse require replacement please contact Bliz zard Lighting for instructions or to return your unit for service Connecting A Bunch of RokSpot Fixtures You will need a serial data link to run light shows using a DMX 512 controller or to run shows on two or more fixtures set to sync in mas ter slave operating mode The combined number of channels required by all the fixtures on a serial data link determines the number of fix tures the data link can support Fixtures on a serial data link must be daisy chained in one single line Also connecting more than 32 fixtures on one serial data link without the use of a DMX optically isolated splitter may result in deterioration of the digital DMX signal The maximum recommended cable run distance is 500 meters 1640
16. izzard Lighting LLC This page has been intentionally left blank Page 19 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC This page has been intentionally left blank Enjoy your product Our sincerest thanks for your purchase The team Blizzard Lighting
17. n and wow factor That s what it s all about after all Returns Gasp We ve taken a lot of precautions to make sure you never even have to worry about sending a defective unit back or sending a unit in for service But like any complex piece of equipment designed and built by humans once in a while something doesn t go as planned If you find yourself with a fixture that isn t behaving like a good little fixture should you ll need to obtain a Return Authori zation RA Don t worry this is easy Just send an email to support blizzardlighting com and we ll issue you an RA Then you ll need to send the unit to us using a trackable pre paid freight method We suggest using USPS Priority or UPS Make sure you carefully pack the fixture for transit and whenever possible use the original box amp packing for shipping When returning your fixture for service be sure to include the following 1 Your contact information Name Address Phone Number Email address 2 The RA issued to you 3 A brief description of the problem symptoms We will at our discretion repair or replace the fixture Please remember that any shipping damage which occurs in transit to us is the customer s responsibil ity so pack it well Shipping Issues Damage incurred in shipping is the responsibility of the shipper and must be reported to the carrier immediately upon receipt of the items Claims must be made within sev
18. ne of the most rockin little spot fixtures on the market today Now that you ve got your RokSpot or hopefully RokSpots you should carefully unpack the box and check the contents to ensure that all parts are present and in good condition If anything looks as if it has been damaged in transit notify the shipper immediately and keep the packing material for inspection Again please save the carton and all packing materials If a fixture must be returned to the factory it is important that the fixture be returned in the original factory box and packing Powering Up All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel is used solely for a 0 to 100 switch AC Voltage Switch Not all fixtures have a voltage select switch so please verify that the fixture you receive is suitable for your local power supply See the label on the fixture or refer to the fixture s specifications chart for more information A fixture s listed current rating is its average current draw under normal conditions Check the fixture or device carefully to make sure that if a voltage selection switch exists that it is set to the correct line voltage you will use Warning Verify that the voltage select switch on your unit matches the line voltage applied Damage to your fixture may result if the line voltage applied does not match the voltage
19. r the internet and from specialty retailers If you d like to build your own the chart below details a proper cable conversion Conductor 3 Pin Female Output 5 Pin Male Input Ground Shield Pin 1 Pin 1 DMX Data Pin 2 Pin 2 DMX Data Pin 3 Pin 3 Not Used No Connection No Connection Not Used No Connection No Connection Take It To The Next Level Setting Up DMX Control Step 1 Connect the male connector of the DMX cable to the female connector output on the controller Step 2 Connect the female connector of the DMX cable to the first fixture s male connec tor input Note It doesn t matter which fixture address is the first one connected We recommend connecting the fixtures in terms of their proximity to the controller rather than connecting the lowest fixture number first and so on Step 3 Connect other fixtures in the chain from output to input as above Place a DMX terminator on the output of the final fixture to ensure best communication Page 9 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC Fixture Linking Master Slave Mode 1 Connect the male 3 pin connector side of the DMX cable to the output female 3 pin connector of the first fixture 2 Connect the end of the cable coming from the first fixture which will have a female 3 pin connec tor to the input connector of the next fixture con sisting of a male 3 pin connector Then proceed to connect
20. urely Verify remote is correct type CA 9 or other as applicable Fixture Moving On Its Own Verify proper mode of operation Is the fixture in Auto mode If your problem persists or isn t listed contact support blizzardlighting com DMX Values In Depth HSV Mode Ch Value What It Does 1 000 lt gt 255 Hue 2 000 lt gt 255 Saturation 3 000 lt gt 255 Value DMX Values In Depth 4 5 Channel Mode Ch Value What It Does 5 Ch What It Does 4 Ch 1 000 lt gt 255 Dimmer 0 lt gt 100 Red Intensity 2 000 lt gt 255 Red Intensity Green Intensity 3 000 lt gt 255 Green Intensity Blue Intensity 4 000 lt gt 255 Blue Intensity White Intensity 5 000 lt gt 255 White Intensity Page 15 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC 5 APPENDIX A Quick Lesson On DMX DMX aka DMX 512 was created in 1986 by the United States Institute for Theatre Technology USITT as a standardized method for connecting lighting consoles to lighting dimmer modules It was revised in 1990 and again in 2000 to allow more flexibility The Entertainment Services and Technology Association ESTA has since assumed control over the DMX512 standard It has also been approved and recognized for ANSI standard clas sification DMX covers and is an abbreviation for Digital MultipleXed signals It is the most common communications standard used by lighting
21. ve mode CHnd 9CH 9 channel DMX mode 8CH 8 channel DMX mode 5CH 5 channel DMX mode 4CH 4 channel DMX mode 3CH 3 channel DMX mode SP SP00 SP15 Speed adjustments 0 15 Pr Pr00 Pr30 Built in programs 0 30 ASC AC00 AC15 Auto mode 0 15 FAdE FA00 FA15 Fade settings 0 15 FLAS FL00 FL15 Flash strobe speed 0 15 rL r 000 r 255 Red dimmer 0 lt gt 100 GL G 000 G 255 Green dimmer 0 lt gt 100 bL b 000 b 255 Blue dimmer 0 lt gt 100 UL U 000 U 255 White dimmer 0 lt gt 100 SouA So uA Sound active mode LED on oFF Display menu on off nodE nod0 nod4 Dimming mode 0 4 UErn UE2 0 Software version Page 12 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC DMX Mode Allows the unit to be controlled by any universal DMX controller 1 The default mode for the fixture is DMX which appears as d001 on the LED Readout To select a different DMX address using the lt MENU gt button select Addr then hit lt ENTER gt Use the lt UP DOWN gt buttons to select the correct address then hit lt ENTER gt to confirm Setting the DMX Channel Mode 1 To select a DMX channel mode press the lt MENU gt button then use the lt UP gt or lt DOWN gt buttons until the display reads Chnd and press the lt MENU gt button Then use the lt UP gt or lt DOWN gt buttons until the display reaches your desired channel mode
22. xture to rain or moisture Make sure there are no flammable materials close to the unit while operating The unit must be installed in a location with adequate ventilation at least 20in 50cm from adjacent surfaces Be sure that no ventilation slots are blocked ALWAYS disconnect from the power source before servicing or replacing fuse and be sure to replace with same fuse size and type ALWAYS secure fixture using a safety chain NEVER carry the fixture by its cord Use its carrying handles DO NOT operate at ambient temperatures higher than 104 F 40 C In the event of a serious operating problem stop using the unit immediately NEVER try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized tech nical assistance center Always use the same type spare parts NEVER connect the device to a dimmer pack Make sure the power cord is never crimped or damaged Never disconnect the power cord by pulling or tugging on the cord Avoid direct eye exposure to the light source while it is on Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact Blizzard Lighting at sup port blizzardlighting com Page 5 RokSpot RGBW Manual Rev A 2013 Blizzard Lighting LLC 2 MEET T
Download Pdf Manuals
Related Search