GPSRXNV-01 - RVR Elettronica SpA Documentation Server
Contents
1. 3 GPS LOCK Green LED when lit on indicates the correct reception of satellite signals 4 EBO OK Green LED when lit on indicates the correct synchronization 5 RS232 DB9 F connector for direct serial communication 6 2 Rear Panel Figure 6 2 1 MAINS VDE connector for mains power supply fuse protection and voltage changer block 100 110 230 250V 50 60Hz 2 BATTERY Switch to enable or disable the power supply of buffer battery 3 ALARMS DB9 M connector for the alarm output status of the equipment through the contacts available 4 10 2 OUT 1 BNC connector for the signal output at 10MHz for the synchronism of the carrier 5 1OMHz OUT 2 BNC connector for the auxiliary signal output at 10MHz for the synchronism of the carrier only in case of presence of proper option 6 10MHz OUT 3 BNC connector for the auxiliary signal output at 10MHz for the synchronism of the carrier only in case of presence of proper option 7 10MHz OUT 4 BNC connector for the auxiliary signal output at 10MHz for the synchronism of the carrier only in case of presence of proper option 8 1 OUT TTL 1 BNC connector for the signal output of 1 PPS TTL for the synchronism of the carrier 9 1pps OUT TTL 2 BNC connector for the signal output of 1 PPS TTL for the synchronism of the carrier only in case of presence of proper option 10 1pps OUT TTL 3 BNC connector for the signal output of 1 PPS TTL for the synchronism of2. B Nr 1 Mains Power Cord The following accessories are also available from Your R V R Dealer Accessories spare parts and cables 4 1 General Description The GPSRXNV 01 produced by R V R Elettronica SpA is a GPS receiver Global Positioning System alias the satellite navigation system developed and maintained by the U S Department of Defense with characteristics that can be used in synchronization systems for isofrequency broadcasting systems SFN alias Single Frequency network The GPSRXNV 01 is designed to being contained into a 19 rack box of 1HE Two major features of GPSRXNV 01 is compact design and user friendliness Another key feature is its modular concept design the different functions are performed by modules with most connections achieved through male and female connectors or through flat cables terminated by connectors This design facilitates maintenance and module replacement The GPSRXNV 01 contains a buffer battery to avoid possible lack of power supply and its internal battery charger Four LEDs on the front panel provide the following status indications AC ON DC ON EBO OK and GPS LOCK The rear panel features the VDE mains input connector with voltage selector that allows to use it with different supply voltages as well as the ON OFF switch of the buffer battery the N type connector for GPS antenna input the BNC connector for 1PPS output signal the BNC connector for 10MHz sync signal and the
3. ES 7 2 Electrical Specifications General A power suppl 100 120 230 250 V 50 60 Hz power supp 12V Accur TC with GPS lock 50 ns 1 10 2 fr n r lt t2x101 P m Integr Antenna Input Connector N type LLL Uscita 5V output for antenna power supply 1pps TTL output nn r BN Typical level TIL 10MHz output Connector o 1 1 1 BNC Signal E dal Typicallevel sD BM OO T ic Di 25 dE Connectors RS232 serial interface DB9 female connector to connect the receiver to an external devices for programming ALARMS interface DB9 male connector signaling of alarm Lu 4 45 O 2 Options DST10 Adds auxiliary ouputs at 10 2 and 2x li 10 14 Rev 1 0 16 11 07 User Manual GPSRXNV 01 2 2 ELETTRONICA 7 3 Spare Parts Subsets for Maintenance Panel r L041PC1001 Interf rd an harger L0411N1001 Power r PSS1201 01 Parts of parts Transformer TREALTOOO1 PS receiver EPSILON BOARD OEM II Buff rv 12V 2Ah 12 2 2 User Manual Rev 1 0 16 11 07 11 14 GPSRXNV 01 an ne ELETTRONICA 8 Module identification 8 1 12 14 GPSRXNV 01 is made up of several modules connected through connectors to facilitate maintenance and replacement if needed Top View The figure 8 1 shows a top view of the equipment and component locations 1 2 3 4 5 6 1 T o Figure 8 1 Panel Board SL041PC1001 Bu
4. DB9 connector for status alarm signaling User Manual Rev 1 0 16 11 07 3 14 GPSRXNV 01 5 1 5 1 1 4 14 Quick guide for installation and use This section provides a step by step description of equipment installation and configuration procedure Follow these procedures closely upon first power on and each time any change is made to general configuration such as when a new transmission station is added or the equipment is replaced Once the desired configuration has been set up no more settings are required for normal operation at each power up even after an accidental shutdown the equipment defaults to the parameters set during the initial configuration procedure The topics covered in this section are discussed at greater length in the next sections with detailed descriptions of all hardware and firmware features and capabilities Please see the relevant sections for additional details The topics covered in this section are discussed at greater length in the next sections with detailed descriptions of all hardware and firmware features and capabilities Please see the relevant sections for additional details Preparation Preliminary checks Unpack the GPS receiver and immediately inspect it for transport damage Ensure that all connectors are in perfect condition Provide for the following applicable to operating tests and putting into service V Single phase 230 or 115 15 10 Vac mains power supp
5. holes are supplied for the ventilation in order to assure a reliable efficacy of the product that for protect itself from excessive heating these fissures do not have to be obstructed or to be covered The fissures doesn t be obstructed inno case The product must not be incorporated in a rack unless it is supplied with a suitable ventilation or that the manufacturer s instructions are been followed A WIRING This equipment can irradiate radio frequency energyand if it s not installed following the instructions contained in the manual and local regulations it could generate interferences in radio communications A WIRING This device has a connection to ground on the power cord and on the chassis Check that they are correctly connected Operate with this device in a residential ambient can cause radio disturbs in this case it can be demanded to the user to take adequate measures Specifications and informations contained in this manual are furnished for information only and are subject to change at any time without notice and should not be construed as a commitment by R V R Elettronica SpA The R V R Elettronica SpA assumes no responsability or liability for any errors or inaccuracies that may appear in this manual including the products and software described in it and it reserves the right to modify the design and or the technical specifications of the product and this manual without notice e Warning regarding the us
6. problem and so that a possible easy solution can be detected Dealers and Distributors are supplied with all the information about problems that may occur and usually they can repair the unit quicker than what the manufacturer could do Very often installing errors are discovered by dealers 2 Ifyour dealer cannot help you contact R V R Elettronica and explain the problem If it is decided to return the unit to the factory R V R Elettronica will mail you a regular authorization with all the necessary instructions to send back the goods 3 When you receive the authorization you can return the unit Pack it carefully for the shipment preferably using the original packing and seal the package perfectly The customer always assumes the risks of loss i e Rev 1 0 16 11 07 1 14 2 14 GPSRXNV 01 R V R is never responsible for damage or loss until the package reaches R V R premises For this reason we suggest you to insure the goods for the whole value Shipment must be effected C I F PREPAID to the address specified by R V R s service manager on the authorization LS DO NOT RETURN UNITS WITHOUT OUR AUTHORIZATION AS THEY WILL BE REFUSED 4 sure to enclose a written technical report where mention all the problems found and a copy of your original invoice establishing the starting date of the warranty Replacement and warranty parts may be ordered from the following address Be sure to include the equipment mo
7. quiet as possible e Loosen their clothing a reclining position is recommended e Call for medical help as soon as possible 3 2 Treatment of electrical Burns 3 2 1 Extensive burned and broken skin o Cover area with clean sheet or cloth Do not break blisters remove tissue remove adhered particles of clothing or apply any salve or ointment o Treat victim for shock as required e Arrange transportation to a hospital as quickly as possible If arms or legs are affected keep them elevated If medical help will not be available within an hour and the victim is conscious and not vomiting give him a weak solution of salt and soda 1 level teaspoonful of salt and 1 2 level teaspoonful of baking soda to each quart of water neither hot or cold Allow victim to sip slowly about 4 ounces half a glass over a period of 15 minutes Discontinue fluid if vomiting occurs DO NOT give alcohol 3 2 2 Less severe burns e Apply cool not ice cold compresses using the cleansed available cloth article e Do not break blisters remove tissue remove adhered particles of clothing or apply salve or ointment e Apply clean dry dressing if necessary Treat victim for shock as required e Arrange transportation to a hospital as quickly as possible e f arms or legs are affected keep them elevated User Manual GPSRXNV 01 4 Unpacking The package contains B Nr 1 GPSRXNV 01 B Nr 1 User Manual
8. the carrier only in case of presence of proper option 11 GSM ANT Type N connector for antenna receiver input 8 14 Rev 1 0 16 11 07 User Manual 6 3 Connectors description 6 3 1 RS232 DB9 female 0 000 G Z 6 3 1 ALARMS DB9 male Pin Name 1 GPS LOCK 2 GPS LOCK GPS LOCK 4 GPS LOCK 5 GND 6 EBO OK 7 EBO OK 8 EBO OK 9 EBO OK User Manual Type OUT dig OUT dig OUT dig OUT an OUT dig OUT dig OUT dig OUT an Rev 1 0 16 11 07 GPSRXNV 01 Purpose Closed contact if PIN2 is in normal operating condition Common contact Closed contact if PIN2 is in alarm condition Tip JP6 SLO411N1001 is in pos 2 3 or 3 4 12V signalling in case of normal operation condition If JP6 SLO411N1001 is in pos 1 2 12V signalling in case of alarm If JP6 SLO411N1001 is in pos 4 5 12V always active GND Closed contact if PIN7 is in normal operating condition Common contact Closed contact if is in alarm condition Tip JP5 51041131001 is in pos 2 3 or 3 4 12V signalling in case of normal operation condition If JP5 SLO411N1001 is in pos 1 2 12V signalling in case of alarm If JP5 51041131001 is in pos 4 5 12V always active 9 14 GPSRXNV 01 T Technical Specifications 7 1 Mechanical Specifications Gize Panel 183 mm 19 027 x 44 mm 1 73 1 HE e
9. GPSRXNV 01 User Manual Volume 1 4 RaW Manufactured by ELETTRONICA Italy Name File 03 GPSRXNV 01 ING 1 0 indd Version 1 0 Date 16 11 2007 Revision History 16 11 2007 First Edition J H Berti 044014 NN GPSRXNV 01 User Manual Version 1 0 Copyright 2007 R V R Elettronica SpA Via del Fonditore 2 2c 40138 Bologna ltalia Telefono 39 051 6010506 Fax 39 051 6011104 Email info rvr it Web www rvr it All rights reserved Printed and bound in Italy No part of this manual may be reproduced memorized or transmitted in any form or by any means electronic or mechanic including photocopying recording or by any informa tion storage and retrieval system without written permission of the copyright owner Declaration of Conformity Hereby R V R Elettronica SpA declares that this FM transmitter is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC 6 R V R GPSRXNV 01 Table of Contents 1 Preliminary Instructions 1 2 Warranty 1 3 First Aid 2 3 1 Treatment of electrical shocks 2 3 2 Treatment of electrical Burns 2 4 Unpacking 3 4 1 General Description 3 5 Quick guide for installation and use 4 5 1 Preparation 4 6 External Description 8 6 1 Frontal Panel 8 6 2 Rear Panel 8 6 3 Connectors description 9 7 Technical Specifications 10 7 1 Mechanical Specifications 10 7 2 Electrical Specifications 10 7 3 Spare Par
10. ble on the DB9 M connector User Manual Rev 1 0 16 11 07 13 14 GPSRXNV 01 9 3 Panel board SL041PC1001 This card is mounted on the frontal panel The panel board provides the visualization via LEDs related to status of equipment Also hosts the RS232 connector for direct serial communication normally used only for factory settings 14 14 Rev 1 0 16 11 07 User Manual
11. del and serial number as well as part description and part number R V R Elettronica SpA Via del Fonditore 2 2c 40138 BOLOGNA ITALY Tel 39 051 6010506 3 First Aid The personnel employed in the installation use and maintenance of the device shall be familiar with theory and practice of first aid 3 1 Treatment of electrical shocks 3 1 1 If the victim is not responsive Follow the A B C s of basic life support Place victim flat on his backon a hard surface Open airway lift up neck push forehead back Figure 1 Figure 1 e clear out mouth if necessary and observe for breathing e if not breathing begin artificial breathing Figure 2 tilt head pinch nostrils make airtight seal four quick full breaths Remember mouth to mouth resuscitation must be commenced as soon as possible Figure 2 e Check carotid pulse Figure 3 if pulse is absent begin artificial circulation Figure 4 depressing sternum Figure 5 Figure 3 Figure 4 Rev 1 0 16 11 07 ELETTRONICA Figure 5 In case of only one rescuer 15 compressions alternated to two breaths e If there are two rescuers the rythm shall be of one brath each 5 compressions e Do not interrupt the rythm of compressions when the second person is giving breath Call for medical assistance as soon as possible 3 1 2 If victim is responsive e Keep them warm Keep them as
12. e designated and the use limitations of the product This product is an transmitter radio indicated for the audio broadcasting service in frequency modulation It uses working frequencies that are not harmonized in the states of designated user The user of this product must obtain from the Authority for spectrum management in the state of designated user the appropriate authorization to use the radio spectrum before putting in exercise this equipment The working frequency the transmitter power let alone other specifications of the transmission system are subject to limitation and definited in the authorization obtained 2 Warranty R V R Electronics S P A guarantees absence of manufacturing defect and the good operation for the products within the provided terms and conditions Please read the terms carefully because the purchase of the product or acceptance of order confirmation constitutes acceptance of the terms and conditions For the last legal terms and conditions please visit our web site WWW RVR IT wich may also be changed removed or updated for any reason without prior notice Warranty will be void in cases of opened products physical damage misuse modification repair by unauthorised persons carelessness and using the product for other purpose than its intended use In case of defect proceed like described in the following 1 Contact the dealer or distributor where you purchased the unit Describe the
13. f the equipment and with responsibility regarding the own safety and the other not qualified staff safety place under his directed surveillance in case of works on the equipment A WARNING The machine can be equipped with an ON OFF switch which could not remove completely voltages inside the machine It is necessary to have disconnected the feeding cord or to have switched off the control panel before to execute technical operations making sure himself that the safety connection to ground is connected The technical interventions that expect the equipment inspection with circuits under voltage must be carry out from trained and qualified staff in presence of a second trained person that it is ready to intervene removing voltage in case of need R V R Elettronica SpA doesn t assume responsibility for injury or damage resulting from improper procedures or practices by untrained unqualified personnel in the handling of this unit A WARNING The equipment is not water resistant and an infiltration could seriously compromise its correct operation In order to prevent fires or electric shocks do not expose the equipment to rain infiltrations or humidity Please observe all local codes and fire protection standards during installation and use of this unit A WARNING The equipment has to its inside exposed parts to risk of electric shock always disconnect power before opening covers or removing any part of this unit Fissures and
14. ffer battery BATTPG12V2A2 Transformer TRFALT0001 Power supply card PSS1201 01 Interface card SL0411N1001 GPS receiver EPSILON BOARD OEM Il Rev 1 0 16 11 07 User Manual GPSRXNV 01 ELETTRONICA 9 Working Principles The figures below provide an overview of GPSRXNV 01 modules and connections GPS Antenna BATTERY CHARGER GPS RX E EO 6 12 5 TTL Output 1OMHZ SYNC Output MAINS Voltage INTERFACE PANEL lt gt MAIN PS Following is a brief description of the different module functions all diagrams and board layout diagrams are included in the Technical Schedule Vol 2 Figure 9 1 9 1 Power supply card PSS1201 01 The power supply section is composed by a transformer which supplies a voltage of 12 V for the power supply of analog section and a voltage of 7 V for the power supply of digital logic section In case of absence of network and in case the switch on the rear panel of the battery is enabled the equipment automatically switches the power supply on the internal buffer battery thus guaranteeing the continuity of the service 9 2 Interface card SL0411N1001 This card performs the following tasksi e Interfacing and control of receiver module EPSILON BOARD e Interfacing and control of power supply module SWPSUPO0003 e Supply and control of LED signalling card e Control of status and alarm indication of equipment made availa
15. l and a compatible PC with Microsoft Windows 98 2000 XP on which you have installed the software furnished The ALARMS DBS9 connector figure 6 2 note 3 from which the signals related to the GPS LOCK and EBO OK front LEDs come issued can be used in SFN systems that require a power lowering in case of failure in GPS synchronism In case DST10 option is present it gives further 3 auxiliary 10MHz outputs and 2 auxiliary 1pps outputs beyond those already available connect the remaining outputs depending on your system configuration A connection example is shown here below Rev 1 0 16 11 07 User Manual la GPSRXNV 01 ELETTRONICA TO TX2 GSM MODEM D 2 He Oe TO TX1 GSM MODEM 2 lt Di me Oa lt GPS ANTENNA INPUT 5 gt GPSRXNV 01 DST10 mee CHANGE OVER Fe TX2 CHANGE OVER Figura 5 3 User Manual Rev 1 0 16 11 07 7 14 GPSRXNV 01 6 External Description A ELETTRONICA This section describes the components found on the front and rear panel of GPSRXNV 01 6 1 Frontal Panel DO GPS RECEIVER gt ec Co Figure 6 1 1 AC ON Green LED when lit on indicates the presence of mains power supply 2 DC ON Green LED when lit on indicates the presence of continuous power supply in case this LED is ON while that AC ON is off it indicates that the receiver is powered by battery
16. ly with adequate earth connection V Connection cable kit including e Mains power cable e Cable to connect the 1 PPS TTL signal sold separately e Cable to connect the 10 MHz signal sold separately e GPS receiver antenna sold separately Rev 1 0 16 11 07 User Manual GPSRXNV 01 5 1 2 Preparation of the mains supply WARNING perform all the operations described in this section with the mains supply disconnected The general fuse is accessible from the outside on the rear panel see figure 6 2 To check the integrity or for substitution remove the fuse holder with a screwdriver The fuse to be used is of type Mains Fuse 1 A 5x20 LE Note the switch with lock position for the connection of buffer battery is kept open BATTERY OFF position during transport Check this condition and set the switch to ON BATTERY position see figure 6 2 note 11 after powering the system 5 1 3 Connections Connect tge GPS ANTENNA input of GPSRXNV 01 see figure 6 2 note 11 to antenna receiver figure 5 1 Obim GPS ANTENNA INPUT gt oS eal Q e so e 9 99 Foy tle i E eS e Bos EXC Hs e G msn 5 Wee sc Q AN Figure 5 1 Connect the 10MHz OUT 1 output of GPSRXNV 01 figure 6 1 note 4 to the proper IN 10MHZ input equipped with apparatus of R V R Elettronica like PTX LCD with SFN option figure 5 1 If the equipment is of a different brand ide
17. ntify an equivalent input Connect the 1PPS OUT TTL 1 output of GPSRXNV 01 figure 6 1 note 8 to the proper REMOTE input equipped with apparatus of R V R Elettronica like PTX LCD with SFN option figure 5 1 If the equipment is of a different brand identify an equivalent input User Manual Rev 1 0 16 11 07 5 14 GPSRXNV 01 i 6 14 Note in the following figure is shown the diagram of cable when connecting equipment of R V R Elettronica like the PTX LCD with SFN option Figure 5 2 Rite Coaxial cole 1 15 Figure 5 2 Connect the power cable in the proper MAINS connector placed on the rear panel figure 6 2 note 1 Note The mains must be equipped with adequate ground connection properly connected to the machine This is a pre requisite for ensuring operator safety and correct operation After connecting the power supply the receiver performs a bootstrap test lighting on in sequence before GPS LOCK led and then EBO OK led soon after light them off Once that 4 satellites are correctly receipt and decodified the GPS LOCK led light on again when the phase locking of 10MHz e 1PPS signal happens the EBO OK will be again light on too In case that you made explicit request for purchase the software license of EPSILON BOARD OEM II card at time of order the reading parameters of GPSRXNV 01 and of satellites will be made through the serial connection between the RS232 and the DB9 placed in front pane
18. ts 10 8 Module identification 12 9 1 Top View 12 9 Working Principles 13 9 1 Power supply card 551201 01 19 9 2 Interface card 510411 1001 13 9 3 Panel board SL041PC1001 14 User Manual Rev 1 0 16 11 07 GPSRXNV 01 Rev 1 0 16 11 07 RaW Ra ELETTRONICA This page was intentionally left blank User Manual ELETTRONICA GPSRXNV 01 IMPORTANT The symbol of lightning inside a triangle placed on the product evidences the operations for which is necessary gave it full attention to avoid risk of electric shocks The symbol of exclamation mark inside a triangle placed on the product informs the user about the presence of instructions inside the manual that accompanies the equipment im portant for the efficacy and the maintenance repairs lt 2 User Manual 1 Preliminary Instructions General foreword The equipment in object is to considering for uses installation and maintenance from trained or qualified staff they conscious of the risks connected to operate on electronic and electrical circuits electrical The trained definition means staff with technical knowledge about the use of the equipment and with responsibility regarding the own safety and the other not qualified staff safety place under his directed surveillance in case of works on the equipment The qualified definition means staff with instruction and experience about the use o
Download Pdf Manuals
Related Search