INTRAPHEX UCI-11 Installation and User Guide
Contents
1. UCI 11C Rear view camera amp Navigation solution for Dodge Chrysler amp Fiat UConnect Touch 4 3 amp 8 4 systems Overview e Adds touch screen controlled navigation to vehicles without factory navigation e Provides a rear view camera solution for both the 4 3 and 8 4 UConnect Touch radios camera not included e Allows DVD video to be viewed while the vehicle is in drive only on 8 4 DVD equipped systems Product Description UCI 11C interface module La Radio T harness LVDS cable USB update cable Video IN cable a 1 Page Connectorpin out Navigation AV USB update port reserved LVDS IN from radio White LED LED Activity N A The connectors are viewed from the wire insertion side 8 Pin Video IN Connector Shield RCA Shield RCA aaa Video Signal Video Signal Bigg Shield RCA 4 Video Twisted 6 Video Signal 8 Video Pair 24 pin Navigation Connector 4 EMPTY 16 EMPTY 6 RGBGREENIN 18 EMPTY 8 RGBSYNCIN 20 EMPTY 9 EMPTY 21 EMPTY LAA ronment Sen pe ABB HoONMMMMMe anagoaprprnacan Radio T Harness LVDS OUT to screen Black 2 Page 18 pin Radio T Harness connector 1 12vPower 10 Ground 4 AudioleftOUT Radio 13 AudioLleftIN Car _ 6 Infotainment CAN HI Radio 15 Infotainment CAN LO Radio _ 8 VehicleCANHI Car 17 VehicleCANLO Car _ 9 VehicleCANHI Radio 18 Vehicle CANLO Radio _ A UCI2. Contrast Video in Motion settings Enable ON 7 Page To view the current hardware software revision e Press the About soft key to show current software revision e Press the Exit soft key to return to the main menu e To return to the system press the Exit soft key Note Changes in the settings menu will not be saved until Exit is pressed Changes will not be saved if the ignition is cycled before the Exit soft key is pressed 65 Operation Rear View Camera pith Esa MORE a SCREEN OFF The rear view surroundings will be displayed anytime the vehicle is shifted into REVERSE The image will be displayed on the factory touch screen along with the text Check Entire Surroundings The text will remain on the screen for 10 seconds and then will fade out Once the vehicle is shifted out of REVERSE the image will fade into the previous mode or screen Do not rely completely on the rear camera image periodically check your surroundings for obstacles Navigation 4 3 monitor To display navigation press the Screen Off button This will display the navigation home page To exit navigation press the Screen Off button again Audio prompts will be heard through the external speaker Refer to the navigation documentation for operation 8 4 monitor When navigation is enabled a new icon will show up in the bottom right corner of the screen where the More soft key is l
3. increments o Press the Exit soft key e To exit the Navigation input setting press the Exit soft key To view the current hardware software revision e Press the About soft key to show current software revision e Press the Exit soft key to return to the main menu e To return to the system press the Exit soft key Camera Settings 8 4 Monitor input Head Unit Brightness Adjusting the rearview camera settings Contrast To access the settings screen Press and hold the radio power button for 3 seconds Saturation If the vehicle has a factory camera set the Camera input to HEAD UNIT All setting s for the factory camera can be changed in the factory not the UCI Settings menu 6 Page ILRI Leag forme DIAS Fe e Onthe touch screen select Camera Input Settings Adjusting the input o Touch the Input soft key o Every press of the icon will change the input OFF Head Unit factory camera Video 1 Video 2 Video 3 The input image will be displayed in the back ground If the radio is set for Head Unit the camera adjustments are accessed in the factory menu Adjusting brightness Oo Touch the Brightness soft key o Press the or soft key to adjust the image in 10 increments o Press the Exit soft key Adjusting Contrast o Touch the Contrast soft key o Press the or soft key to adjust the image in 10 increments
4. to secure the module in place 4 Plug the routed cable from the UCI into the Directus navigation unit a Black Din RGB b Grey Din DATA c 4 pin MOLEX DC IN NOT USED 5 Included in the kit is an external speaker it is used for turn by turn navigation or any audio output from the navigation unit The speaker can be mounted on one of the metal rails running vertically under the steering column It is recommended that the speaker faces the opening under the steering column for best volume 6 Plug the speaker into the 3 5mm jack labeled SPK on the navigation en 4 Page MITT formeru joe pe 7 The GPS antenna needs to be installed right side up in a location that has a clear line of sight of the sky The antenna can be mounted on the dash or located in the dash below the dash pad without any metal obstructions Be sure the antenna is securely mounted with Velcro 2 sided stick tape or onto a metal surface 8 Connect the antenna to the jack labeled GPS ANT on the navigation unit 9 Return to step 13 in the UCI installation instructions above hy Settings 4 3 Monitor Adjusting the rearview camera settings To access the settings screen press and hold the Settings button for 3 seconds e On the touch screen select Camera Input Settings Adjusting the input o Touch the Input soft key SUCI by NAV TV o Every press of the icon will change the input OFF DIFF a factory camera Video 1 V
5. Installation TOOLS REQUIRED Phillips head screwdriver Plastic pry tool Small pocket screwdriver Refer to online document for vehicle specific installation 1 Gain access to the back of the radio head Pull out the radio enough to access the wiring behind the radio 2 Disconnect the white 22 pin connector from behind the radio gateway 3 Inthe kit is a 22 pin T harness connect the removed harness from the radio to the female receptacle of the supplied harness Take care not to bend any of the pins in the female receptacle when inserting 4 Plug the male plug of the T harness into the radio where the factory connector was located _ 3 Page PULTS formerty SiS een pe 5 Gain access to the rear of the screen amp disconnect the 3 cables that are attached Set the unit aside for ease of installation of the UCI The free end of the 22 pin T harness that is plugged into the radio head is routed behind the dash to the screen location 8 The 18 pin connector is inserted into the port labeled Radio T harness 9 Locate the WHITE ROUND connector that was removed from the screen Insert this cable into the WHITE port labeled LVDS IN 10 Take the provided LVDS cable and insert the BLACK end into the BLACK port LVDS OUT The other end will be connected to the screen later 11 If installing a rear view camera insert the 8 pin MOLEX plug into the port labeled Video IN Of the connections available
6. e image isn t displayed properly ie garbled or skewed A On the Kenwood navigations verify the Blue Black wire in position 12 is cut for a 4 3 screen or intact for an 8 4 screen The Directus units are preconfigured for a specific screen size Verify that the correct navigation unit is being installed for the particular screen in the vehicle These units cannot be user configured p 9 Page WMILAPHEY foment BSS US
7. ideo 2 Video 3 The input Camera input settings image will be displayed in the back ground Navigation input settings About Adjusting brightness o Touch the Brightness soft key o Press the or soft key to adjust the image in 10 increments o Press the Exit soft key WIP REY former Snes 5 Page Adjusting Contrast o Touch the Contrast soft key o Press the or soft key to adjust the image in 10 Camera Settings increments Video 1 o Press the Exit soft key Brightness Adjusting the Saturation Contrast o Touch the Saturation soft key Saturation o Press the or soft key to adjust the image in 10 Exit increments o Press the Exit soft key e To exit the Camera Input Setting press the Exit soft key Adjusting the navigation settings if installed e Press the Navigation input settings soft key Adjusting the input o Touchthe Input soft key o Every press of the icon will change the input OFF RGB Navigation Settings T Video 1 Video 2 Video 3 The input image will be displayed in the back ground Input RGB Adjusting brightness erness o Touch the Brightness soft key o Press the or soft key to adjust the image in 10 increments o Press the Exit soft key Adjusting Contrast o Touch the Contrast soft key o Press the or soft key to adjust the image in 10
8. o Press the Exit soft key Adjusting the Saturation o Touch the Saturation soft key o Press the or soft key to adjust the image in 10 increments o Press the Exit soft key e To exit the Camera Input Setting press the Exit soft key Adjusting the navigation settings if installed e Press the Navigation input settings soft key Adjusting the input o Touch the Input soft key o Every press of the icon will change the input OFF amp ON Only the RGB input is available The input image will be displayed in the back ground Adjusting brightness o Touch the Brightness soft key o Press the or soft key to adjust the image in 10 increments o Press the Exit soft key Adjusting Contras o Touch the Contrast soft key o Press the or soft key to adjust the image in 10 increments o Press the Exit soft key e To exit the Navigation input setting press the Exit soft key Changing the Video in motion settings e Press the Video in Motion soft key o Touch the Video in Motion soft key to change status ON or OFF This function enables and disables the ability to watch DVD videos while the vehicle is in drive o Press the Exit soft key to return to the main menu PILLER tormens Serres Camera Settings input Head Unit Brightness Contrast Saturation Navigation Settings Navigation On Brightness
9. ocated To access the navigation press the Nav soft button on the lower right corner The navigation screen will be displayed All the functions of the navigation can be controlled through the factory touch screen Refer to the user manual for operation To exit the navigation screen press the desired source The More soft touch button for the factory SETTINGS screen can be accessed through the navigation screen While in navigation mode if the climate control is adjusted the navigation screen will disappear anytime the system is being accessed 3 seconds after the last operation the navigation screen will return 8 Page WIZ mamas forme PINS Fe FAQ Q When the vehicle is in reverse get a blank screen A Verify that whatever input the camera is connected to i e video 1 which is what is selected in the Camera Settings Input If the wrong input is selected there will not be an image Q When the vehicle is in reverse the camera image is garbled and flickers A The camera is insufficiently powered The common cause is the camera is powered from the reverse lamps It is recommended to make the power connections at the cigarette lighter Q When I change the settings in the UCI menu they re not being saved A To save the changes in the settings menu the Exit icon needs to be used to exit the menu Any other way of exiting the menu will not save the settings Q When display the navigation screen th
10. there s a Twisted Pair Used for factory installed camera only on the 4 3 screens This input is not used on the 8 4 screens On the 8 4 screens the factory camera input is on the back of the radio head b Video 1 2 amp 3 Used for an aftermarket camera input using composite video yellow RCA connection Power connections for therear view camera can be made at the cigarette lighter 12 If installing navigation into the system proceed to the navigation installation section Otherwise continue to step 13 13 After all the connections are made securely mount the UCI module in the dash 14 Connect the WHITE end of the provided LVDS cable into the screen Make all other connections and reassemble the radio screen 15 Make the necessary changes in the SETUP menu amp test 16 Using the plastic pry tool gently pry around the dash panel to release the locking tabs Take extra care when releasing these tabs they may fall from the dash panel and into the dash If Installing Directus Navigation Once you complete step 12 of the UCI installation continue from this point 1 Plugin the supplied 24 pin Navigation harness into the port labeled NAVIGATION AV Route this cable down to the driver s side under dash or any location that is secure Be sure to securely fasten it to existing wiring and brackets Route away from any sharp or moving parts 3 Using Velcro secure the module For added stability a large zip tie should be used
Download Pdf Manuals
Related Search