victron energy
Contents
1. check connections and cables No output voltage Over Temp indicator on Load less than 650W Thermal shutdown Improve ventilation make sure ventilation shafts of the inverter are not obstructed Lower ambient temperature No output voltage Short circuit or Wiring Check AC wiring Overload indicator on error for short circuit or Very high power load improper polarity hot and neutral reversed Remove load Ny victron energy 16 manual 5 Maintenance Very little maintenance is required to keep your inverter operating properly You should clean the exterior of the unit periodically with a damp cloth to pre vent accumulation of dust and dirt At the same time tighten the screws on the DC input terminals victron energy manual My De Paal 35 1351 JG Almere Haven The Netherlands T 31 0 36 5359700 F 31 0 36 5311666 sales victronenergy com www victronenergy com victron energy manual My2. 1 1 1 Do not expose the Inverter to water mist snow or dust To reduce the risk of hazard do not cover or obstruct the ventilation shaft Do not install the Inverter in a zero clearance compartment Overheating may occur 1 1 2 To avoid the risk of fire and electronic shock make sure that existing wiring is in good electrical condition and not undersize Do not operate the Inverter with damaged or substandard Wiring 1 1 3 There are some components in the inverter can cause arcs and sparks To prevent from fire or explosion do not put batteries flammable materials or anything should be ignition protected around the inverter Precautions When Working with Batteries 1 2 1 If battery acid contacts your skin or clothing you need to wash it out immediately with soap and water If acid enters into your eyes immediately flush your eyes with running cold water for at least 20 minutes and get medical attention immediately 1 2 2 Never smoke or make a spark or flame in the vicinity of batteries or Engines 1 2 3 Do not drop a metal tools on the battery The resulting spark or short circuit on the battery or other electrical parts may cause an explosion 1 2 4 Remove personal metal items such as rings bracelets necklaces and watches when working with a lead acid battery A lead acid battery may produce a short circuit current who s temperature is high enough to weld these metal items and cause a severe burn victron ener
3. EAA A OO WARNING REVERSE POLARITY WILL DAMAGE UNIT 3 2 1 Remote ON OFF switch for S600R model only 3 2 1 1 To operate the inverter with Remote ON OFF switch ON OFF switch on the Front Panel should be off 3 2 1 2 Ensure the remote control contact is off 3 2 1 3 Use 14 20 AWG wire to connect the Rear Panel Terminal marked REMOTE PORT to the remote control contact the remote control contact is in a state of low impedance short the inverter will be turned ON If the remote control contact is in a state of high impedance open the inverter will be turned OFF manual Ny victron energy 3 2 2 Ventilation Shaft Be sure to keep it a distance at least 1 inch form surrounding things 3 2 3 Input terminals Connect the input terminal to 12V 24V battery or other 12V 24V power source represents positive and represents negative Reverse polarity connection will blow the internal fuse and may damage the inverter permanently 3 2 4 Use wire 8 AWG to connects Chassis ground with Vehicle Chassis WARNING Operating the inverter without a proper ground connection may cause an electrical safety hazard victron energy 8 manual Ny 3 3 Installation The power inverter should be installed in an environment that meets the following requirements 3 3 1 3 3 2 3 3 3 3 3 4 3 3 5 3 3 6 Dry Do not allow water to drip on or en
4. al Safety Precautions rrrnnnnnannrnonnnnnnnnerernrrnrnnnnnene 1 1 2 Batteries Precautions rannnnnrannnnvrnnnnnerensnnerennerenensenenennn 1 2 FP AtUIS Hk ee 2 221 Applications iscyaseyet hse E ete sak tee et ee ee es 2 2 2 Electrical Performance arnnnaronnnranennnnernnnererennenensnnerenennnn 3 2 3 Mechanical Drawings rrnrnnrnnnnnvnnnnnnervnnnnerennenernrnenernnenen 4 OIKStrudtl0ns arsrsserieteebrdeedekrresamrennadeneaeadenvanaerden skrinet rand 5 3 1 Front Panel Operation rarnonnnnnvrnvrnnrvnnennrnnnnvenennennennenseenn 5 6 3 2 Rear Panel Operation arrnnnonnvnnrnnernvrennennennernenneneenennensnn 7 8 3 3 dnstallation vgs oh avd eeeeededte st gitte 9 3 4 Quick hook up and Testing rrnrrnrrnnnrnnnnnrnnvrrrnrnnrnnennensnenn 10 11 3 5 AC Safety Grounding onnrnnvranrorrrnnvnnennereenennennerneneennnntnnnn 12 13 3 6 DC Wiring Connections rnnnrnnvrvnnrnnrnnrennnerennrnnennenennnnne 13 14 3 7 Inverter Operation ararnnnnarnvnnnnnennernnrnersnnnnnernernernerennennene 15 MPOUDIOSNOOUUNG o c6 cacces sei coccece ves ewe secene caccecevee seeeecewcnceeweetereseetecies 16 lt MaintOnanCe aein aa tad ieces sucedenteed ett ANARA 17 victron energy manual My 1 Important Safety Information WARNING Before installing and using the Inverter you need to read Following safety information carefully 1 1 General Safety Precautions 1 2
5. gy manual My 2 Features m Pure sine wave output THD lt 3 m Output frequency 50 60Hz switch selections m Input amp output fully isolated design m High efficiency 88 94 m Driving highly reactive amp capacitive load at start moment m Tri Color indicators show input voltage amp output load level m Loading controlled cooling fan m Advanced microprocessor m Protection Input low voltage Overload Short circuit Low battery alarm Input over voltage Over temperature 2 1 Applications 2 1 1 Power tools circular saws drills grinders sanders buffers weed and hedge trimmers air compressors etc 2 1 2 Office equipment computers printers monitors facsimile machines and scanners etc 2 1 3 Household appliances vacuum cleaners fans fluorescent and incandescent lights shavers sewing machines etc 2 1 4 Kitchen appliances microwave ovens refrigerators and freezers coffee makers blenders ice makers toasters etc 2 1 5 Industrial equipment metal halide lamp high pressure sodium lamp etc 2 1 6 Home entertainment electronics television VCRs video games stereos musical instruments satellite equipment etc Ny victron energy 2 manual 2 2 Electrical Performance Item 12 650 24 650 12 650 24 650 Continuous Output Power 650W Maximum Output Power 3Min 680W Surge Rating 800W Input voltage 12V 24V 12V 24V O
6. k and inspect the power inverter the switch is OFF 3 4 2 Connect the cables to the power input terminals on the rear panel of power inverter The red terminal represents positive and black terminal represents negative Insert the cables into the terminals and clamp the nuts and the wires securely WARNING You may observe a spark when you make this connection since current may flow into charge capacitors in the power inverter Do not make this connection with the flammable fumes close by Explosion or fire may occur WARNING Ensure all the DC connections are tight torque to 9 10 ft lbs 11 7 13 Nm Loose connections and overheat may result in a potential hazard Ny victron energy 10 manual 3 4 3 Before proceeding further carefully check that cable you have connected does tie negative terminal of inverter to the negative output power source CAUTION Reverse polarity connection will blow the fuse in inverter and may permanently damage the inverter Damage caused by reverse polarity connection is not covered by warranty 3 4 4 3 4 5 3 4 6 3 4 7 Connect the cable from the negative terminal of the inverter to the negative terminal of the power source Make a secure connection Set the power switch to the ON position and the buzzer will send out beep sound at the moment the inverter will make self diagnosis and the LED s indicators will also appear
7. nect the battery cables to the DC input terminals on the Inverter The cables should be as short as possible less than 10 feet 3 meters ideally and large enough to handle the required current in accordance with the electrical codes or regulations applicable to the installation Cables that are not an adequate gauge too narrow or too long will deteriorate inverter performance such as poor surge capability and frequent low input voltage warnings and shutdowns These low input voltage warnings are due to DC voltage drop across the cables from the inverter to the batteries The linger and narrower the cables the greater the voltage drops WARNING The fuse must be installed on positive cable Failure to place a fuse on cables running between the inverter and battery may cause damage to the inverter and will void warranty victron energy manual My Increasing DC cable size helps improve the situation Victron recommends the following cables for optimum inverter performance apply both 120V and 230V versions Model No Wire AWG Inline Fuse 12 650 4 100A 24 650 6 50A Also use only high quality copper wiring and keep cable length short a maximum of 3 6 feet f 7 INLINE FUSE BATTERY victron energy 14 manual Ny 3 7 Inverter Operation To operate the power inverter use the ON OFF switch on the Front pa
8. nel to turn the power on Then the power inverter is ready to deliver AC power to the loads If you are operating several loads from the power inverter turn them on separately after the inverter is on This will ensure that the power inverter does not have to deliver the starting currents for all the loads at one time 3 7 1 Controls and indicators The ON OFF switch turns the control circuit in the power inverter on and off It does not disconnect power from the power inverter The Inverter operates from an input voltage ranging of 10 5 to 15 0 VDC for 12V models 21 0 to 30 0 VDC for 24V models The Inverter will indicate high and low DC voltage conditions as follows Model Dc Input over Voltage shut down Dc Input under Voltage alarm Dc Input under Voltage shut down 12 650 15 3 11 0 10 5 24 650 30 6 22 0 21 0 manual Ny victron energy 4 Troubleshooting WARNING Do not open or disassemble the inverter Attempting to service the unit yourself may cause an electrical shock or fire Problems and Symptoms Possible Cause Solutions Low output voltage Using average reading Use true RMS reading meter and cable 110V 95 105VAC Voltmeter 220V 190 210VAC See page 11 3 4 7 of the manual Load LED bar flash Overload Reduce load No output voltage Voltage indicator In the lower red zone Low input voltage Recharge battery
9. s model 3 1 Front Panel Operation 3 1 1 Front view oO PURE SINE WAVE INVERTER Li 2 a pp EE U mnndi Mmm LOAD 5 LEVEL 2 AI FAULT C rnin INPUT gt LEVEL 2 3 1 2 ON OFF switch Leave the switch in the down position OFF during installation 3 1 3 Input Level Display Input Voltage LED Status DC 12V DC 24V Slow Red Blink 10 5 10 9 21 0 21 8 Red 10 9 11 3 21 8 22 6 Orange 11 3 12 0 22 6 24 0 Green 12 0 14 0 24 0 28 0 Orange Blink 14 0 14 7 28 0 29 4 Over Red Blink 14 7t 29 4t manual Ny victron energy 3 1 4 Load Level Display AC Load Watts LED Status Load Condition Dark 0 30W Green 30W 200W Orange 200W 450W Red 450W 580W Red Blink Over 580W 3 1 5 Failure Display failure status OVP over voltage protection UVP under voltage protection OTP over temperature protection OLP over load protection 3 1 6 AC outlet Outlet Sockets available Europe IEC Continental Europe SCHUKO North America GFCI victron energy manual My 3 2 Rear Panel Operation i DC INPUT WARNING REVERSE POLARITY WILL DAMAGE UNIT NEG POS REMOTE PORT S gt Ha CHASSIS GROUND AN 2 LY DC INPUT NEG POS AO
10. ter into the inverter Cool Ambient air temperature should be between 0c and 336 the cooler the better Safe Do not install the inverter in a battery compartment or other areas where flammable fumes may exist such as fuel storage areas or engine compartments Ventilated Keep the inverter a distance at least one inch away from surrounding things Ensure the ventilation shafts on the rear and the bottom of the unit are not obstructed Dust free Do not install the Inverter in dusty environment The dust can be inhaled into the unit when the cooling fan is working Close to batteries Avoid excessive cable lengths Do not install the Inverter in the same compartment as batteries Use the recommended wire lengths and sizes see section 3 6 Do not mount the inverter where it will be exposed to the gases produced by the battery These gases are very corrosive and prolonged exposure will damage the Inverter WARNING Shock Hazard Before proceeding further carefully check that the Inverter is NOT connected to any batteries and that all wiring is disconnected from any electrical sources Do not connect the output terminals of the Inverter to an incoming AG source victron energy manual My 3 4 Quick hook up and testing For a quick hook up of the power inverter to check its performance before going ahead with installation please follow these guidelines 3 4 1 To check its performance unpac
11. utput Voltage 100 110 120V 3 220 230 240V 3 Fr n PEE EN Pee ME Efficiency full load 87 0 90 0 90 0 93 0 No Load Current Draw 0 87A 0 43A 0 83A 0 43A Output Waveform Pure Sine Wave THD lt 3 Output voltage Regulation 100 110 120V RMS 10 4 220 230 240V RMS 10 4 Input Voltage Regulation 10 5 15 21 0 30 10 5 15 21 0 30 VDC VDC VDC VDC Input Level Indicator Load Level Indicator Red Orange Green LED Failure Indicator Red LED Protection Overload Short Circuit Reverse Polarity Fuse Over Under Input Voltage Over Temperature Safety Certification UL458 EN60950 1 EMC EN50081 1 1992 EN50082 1 1992 EN55022B 1994 EN61000 4 2 1995 EN61000 4 3 1996 ENV50204 1995 e mark e13 020866 FCC Class B Operating Temperature Range 0 33 0 40 Storage Temperature Range 30 to 706 Cooling Loading controlled cooling fan Dimensions 295 L x 180 w x 72 H mm 11 61 L x 7 09 W x 2 83 H Inch Weight 2 7kgs 5 4Lbs 2 3 Mechanical Drawing Er 22829 8 Momin Ny victron energy 4 manual 3 Instructions This power inverter series is one of the most advanced line of mobile AC power systems To get the most effective power inverter it must be installed and used properly Please read the instructions of this manual before you install and operate thi
12. various colors Finally the buzzer will send out another beep sound and the input Level LED indicators will turn to Green color and the inverter starts working successfully Set the power switch to OFF position the inverter stops and all the lights go Off Set power inverter switch to the ON position and turn the test load on The inverter should supply power to the load If you plan to accurately measure the true output r m s voltage of inverter a meter such as FLUKE 45 BECKMAN 4410 or TRIPLETT 4200 must be used victron energy manual My 3 5 AC Safety Grounding During the AC wiring installation AC input and output ground wires are connected to the inverter The AC input ground wire must be connected to the incoming ground from AC utility source The AC output ground wire should go to the grounding point for your loads for example a distribution panel ground bus 3 5 1 Neutral Grounding GFCI S 3 5 1 1 120V models The neutral conductor of the AC output circuit of the Inverter is automatically connected to the safety ground during inverter operation This conforms to National Electrical Code requirements that separately derived from AC sources such as inverters and generators which have their neutral conductors tied to ground in the same way as the neutral conductors from the utility tied to ground at the AC breaker panel For models configured with a transfer relay while AC utility power is present and the In
13. verter is in bypass mode this connection the neutral of the Inverter s AC output to input safety ground is not present so that the utility neutral is only connected to ground at your breaker panel as required WARNING The risk of electronic shock Use only pass and Seymour type 2091 W ground fault circuit interrupter receptacles Other types may fail to operate properly when connected to this inverter equipment 3 5 1 2 230V models There is no connection made inside the Inverter from either the line or neutral conductor to safety ground Ny victron energy 12 manual 3 6 Ground Fault Circuit Interrupters GFCI Installations in Recreational Vehicles for North American approvals will require GFCI protection of all branch circuit connected to the AC output of the hardwire terminal equipped with Inverter In addition electrical codes require GFCI protection of certain receptacles in residential installations While the pure sine wave output of the Inverter is equivalent to the waveform provided by utilities compliance with UL standards requires us to test and recommend specific GFCI Victron has tested the following GFCI protected 20A receptacles and found that they functioned properly when connected to the output of the Inverter WARNING Do not operate the power inverter without connecting it to ground Electrical shock hazard may occur DC Wiring Connections Follow this procedure to con
14. victron energy My USER MANUAL Phoenix 12 650 Phoenix 24 650 CE Copyrights 2005 Victron Energy B V All Rights Reserved This publication or part thereof may not reproduced in any form by any method for any purpose VICTRON ENERGY B V MAKES NO WARRANTY EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE REGARDING THESE VICTRON ENERGY PRODUCTS AND MAKES SUCH VICTRON ENERGY PRODUCTS AVAILABLE SOLELY ON AN AS IS BASIS IN NO EVENT SHALL VICTRON ENERGY B V BE LIABLE TO ANYONE FOR SPECIAL COLLATERAL INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING OUT OF PURCHASE OR USE OF THESE VICTRON ENERGY PRODUCTS THE SOLE AND EXCLUSIVE LIABILITY TO VICTRON ENERGY B V REGARDLESS OF THE FORM OF ACTION SHALL NOT EXCEED THE PURCHASE PRICE OF THE VICTRON ENERGY PRODUCTS DESCRIBED HERE IN For conditions of use and permission to use this manual for publication in other than the English Dutch French or German language contact Victron Energy B V Victron Energy B V reserves the right to revise and improve its products as it sees fit This publication describes the state of this product at the time of its publication and may not reflect the product at all times in the future victron energy manual My Table of contents Important Safety Information cccceeeeeeeeeeeeeeeeeeeeeeeeeseeeeeeeeeee 1 1 1 Gener
Download Pdf Manuals
Related Search