ST Series User Manual
Contents
1. c Adding New User with Administrator Already Setup 1 Press and hold the Down Button on the back of the panel for 2 seconds until the display panel lights up and digits appear release the button after a number appears on the screen this number will be 1 at this stage 2 Press the Down Button to confirm 3 The back light will display the symbol he and request the input of one of the existing administrators fingerprints 4 Input the new administrator fingerprint The back light will display the symbol U indicating that input is successful The symbol b indicates recognition failure 5 You will hear 5 short beeps followed by a long beep and then the front panel will light up Place the finger on the fingerprint sensor until you hear a long beep and the purple light comes on 6 Take your finger off the fingerprint sensor and then place it on the fingerprint sensor again until you hear a second long beep Repeat the process a third time until a third long beep 7 When the blue light comes on you ll know setup is complete Attention Please roll the tip of your finger slightly during the setup process to make sure the sensor will be able to verify the fingerprint 10 There are three types of PIN codes 1 The Administrator PIN Code 1 set required before any type of code change can take place 2 User PIN code 2 sets 3 Single Entry PIN Code 1 set expires after a single use 1 Administrator PIN Code Setu2. Setting Up New Administrators Using Administrator Fingerprints 1 Press and hold the Down Button on the back of the panel for 2 seconds until the display panel lights up and a number appears Then release the button the number 1 will appear at this time 2 Press the Up Button once to select the number 2 and press the Down Button and the Button until you hear a beep as reconfirmation 3 The back light will display the symbol _ and request the input of one of the existing administrators fingerprints 4 Input the new administrator fingerprint The back light will display the symbol U indicating that input is successful The symbol indicates recognition failure 5 The back light displays the numbers 1 through 4 which represent the 4 administrator fingerprint identities Please press the Up Button to select the number you want If the indicator light keeps flashing it means that there is already fingerprint identity stored in that location Press the Down Button to select the number you want 6 You will hear a long beep following 5 short beeps the front panel will then light up Place the finger on the fingerprint sensor until you hear a long beep and the purple light comes on 7 Take your finger off the fingerprint sensor and then place it on the fingerprint sensor again until you hear a second long beep Repeat the process a third time until a long beep 8 When the blue light comes on Your setup is ocmplete 09
3. Lock Status Light Sounds Blue 1 beep Red 3 beeps Purple 2 beeps Red 5 long beeps J4 beep after a valid PIN code fingerprint is entered Jindicates that the door is open The door locks automatically 1 5 seconds after the lever returns to the original horizontal position Types of Fingerprints amp PIN Code Quantity Function 150 50 persons Unlocking the door 12 4 persons Adding overwriting fingerprints 1 set Adding overwriting PIN Codes 2 sets Unlocking the door 06 Factory Default Settings Press the Up and Down Buttons on the back of the lock simultaneously until you see the blue light and all the general user fingerprint will be deleted Fingerprint Management There are 2 types of fingerprints Administrator fingerprints and general user fingerprints Simple Management General Users Only All users are equal no administrators needed Add users without having to enter an administrator s fingerprint You can only delet users by resetting the lock to factory defanlt setting Advanced Management General Users with Administrators There are 2 categories of users for users for fingerprints management general users and administrators Notice Memory function there is no need to reset the fingerprint and PIN Code after battery replacement When using the advanced management mode you cannot go back to simple management mod
4. SCG Sun Castle Global Precision Technology Co Ltd Taichung Headquarters No 1 3 Lane 1010 Zhongshan Rd Shengang Township Taichung County 429 Taiwan R O C TEL 886 0 4 25629136 8 FAX 886 0 4 25624697 Taipei Office 2C09 No 5 Sec 5 Xinyi Rd Taipei City 110 Taiwan R O C TEL 886 0 2 27296294 FAX 886 0 2 87862174 China Office Room 807 Area C Xinxin Jingdi Building Jiahe Rd Huli Xiamen 361009 China TEL 86 0 592 5236752 FAX 886 0 592 5281985 lll SCG Creating Quality SCG ST Series User Manual 01 Important Notes Product Overview Unlocking Methods Fingerprint Management Overview General User Setup Administrator Setup New Administrator Setup New General User Setup with Admin Administrator PIN Code Setup User PIN Code Setup Single Entry PIN Code Setup PIN Code Reset Optimum Volume Seitings Factory Default Settings 03 04 05 06 07 07 08 09 10 10 11 11 12 12 ST1 ST8 02 03 1 Keep your fingers clean when using the lock 2 Please keep the fingerprint sensor clean to ensure proper performance of the lock We recommend periodic cleaning with a cotton cloth 3 5 continuous failed operations will shut down the system for one minute to prevent unauthorized entry 4 When the battery is low the lock will emit a continuous beep after a successful operation 5 The lock memory can store 150 fingerprints We suggest that you
5. e To delete all users and general user fingerprints please restore factory default settings Please note that the administrator fingerprints will remain in the memory 07 I Fingerprint Setup A Setup as a general user directly add new fingerprints without administrator authentication 1 Press and hold the Down button on the back panel for 2 seconds until a number appears on the display panel and then release the button the number on the display panel will be 1 at this stage Press the Down Button again to confirm 2 There will be 5 short beeps followed by a long beep the front panel will light up then place your finger on the fingerprint recognition sensor until you hear a long beep and a purple light comes on 3 Take your finger off the fingerprint sensor and then place it back on the fingerprint sensor again until you hear a second long beep Repeat the process a third time until a third long beep 4 When the blue light comes on you ll know that setup is complete Symbol indication U setup complete setup failure F memory is full If new fingerprints are required restore the system to factory default settings before entering new fingerprints B Advanced Administrator Setup 1 Enhanced fingerprint lock administrator mode the presence of an administrator is needed when adding new users 2 1 4 administrator user logins can be created 3 Administrator fingerprints cannot be deleted a Setup as Ad
6. ministrator 1 Press and hold the Down Button on the back of the panel for 2 seconds until the display panel lights up and digits appear release the button after a number appears on the screen this number will be 1 at this stage 2 Press the Up Button once to enter the number 2 and press the Down Button and to confirm until you hear a beep as reconfirmation 3 The back light displays the numbers 1 through 4 which represent the 4 administrator fingerprint identities Please press the Up Button to select the number you want If the indicator light keeps flashing it means that there is already fingerprint identity stored in that location Press the Down Button to select the number you want 08 4 You will hear a long beep following 5 short beeps and the front panel will then light up Place the finger on the fingerprint sensor until you hear a long beep and the purple light comes on 5 Take your finger off the fingerprint sensor and then place it on the fingerprint sensor again until you hear a second long beep Repeat the process a third time until a third long beep 6 When the blue light comes on you ll know setup is complete Attention An administrator fingerprint cannot be deleted after it has been setup in the system but it can be replaced by other administrator fingerprints Once an administrator fingerprint is setup this administrator fingerprint must be input before any new user fingerprints can be added b
7. oB x A temporary PIN code cannot be 000000 or 123456 admin PIN no loud Exit 1 Input Admin PIN Code and then press purple light 2 Wait for 2 beeps to sound then press 04 3 Press the Volume Number 00 silent 01 low 02 medium 03 loud 4 Press to exit the system PIN Code Reset The preset PIN Codes cannot be deleted but they can be pevre OG Inn admin PIN no PIN Confirm Exit 1 Input Admin PIN Code and then press purple light 2 Wait for 2 beeps to sound then press 00 01 02 03 the PIN you want to Factory Default Settings replace Press the Up and Down Buttons on the back of the lock simultaneously 3 Press the intended PIN code consisting of 4 8 digits and then press to until you see the blue light and all the general user fingerprint and PIN confirm codes will be deleted 4 Press again to exit the system 13 Indication 1 The fingerprint is not stored yet 2 The fingerprint may not be stored correctly 3 The fingerprint sensor needs to be cleaned Advanced Management is set up Add Overwrite new users with administrator authentication Low battery alert Replace the battery immediately 1 Battery is dead 2 3 consecutive PIN code entry errors Please try again after 1 minute Provider of Comfort amp Safety 14 Headquarters No 1 3 Lane 1010 Zhongshan Rd Shengang Township Taich
8. p Meriasek Koo _______ J no Admin PIN Confirm Exit 1 Input factory default administrator code 123456 and then press purple light 2 Wait for 2 beeps to sound then press 00 2 3 Press the intended admin PIN code consists of 4 8 digits and then press to confirm 4 Press again to exit the system The Administrator PIN code cannot be 123456 or 000000 If a red light appears during this process it means the setup has failed A blue light indicates successful operation We strongly recommend that you change the administrator code immediately upon receiving this product 2 User PIN Codes Setup There are 2 User PIN Codes for the locks of the ST Series Ia A KON l a admin PIN no PIN Confirm Exit 1 Input Admin PIN Code and then press purple light 2 Wait for 2 beeps to sound then press 01 or 02 3 Press the intended PIN code consisting of 4 8 digits and then press to confirm 4 Press again to exit the system 11 12 Single Entry PIN Code Setup 22288 E OH oo L J oB n J admin PIN no silence Exit admin PIN no PIN Confirm Exit 0 CLL oA oA W 1 Input Admin PIN Code and then press purple light admin PIN no low Exit e T a ma o ress the intended single entr ode consisting of 4 8 digits an ecu a i i admin PIN no medium Exit 4 Press again to exit the system DI oA
9. store at least 2 valid sets of fingerprints per person in the system 6 If fingerprints and codes fail to unlock the door try using the emergency override keys 7 To ensure optimal performance of your lock make sure to read the user manual carefully Here is the correct way to place your finger on the sensor Wrong examples 04 Light Blue light operation success Red light operation failure Purple light setup mode Keypad PIN codes consist of 4 8 digits Confirm Exit Button Keyhole Cover use the magnet on the key chain key provided in the package and turn the keyhole cover 90 degrees clockwise to remove it Factory Default Settings press the Up and Down Buttons simultaneously for 2 seconds until you hear a long beep The Up button is the Select Button and the Down Button is the Confirm Button Fingerprint Recognition Sensor D ST8 ha The keyhole cover of the ST8 looks like this Please press the cover to open X _____ Use the magnet to remove J the keyhole cover Emergency override key 05 1 Using fingerprint recognition press and then place the finger on the sensor 2 Using PIN Code enter an assigned PIN code and press 3 Using the Mechanical Key use the magnet on the key chain key provided in the package and turn the keyhole cover 90 degrees clockwise to remove it Then use the key to open the door manually Door
10. ung County 429 Taiwan R O C TEL 886 0 4 25629136 8 FAX 886 0 4 25624697 Taipei Office 2C09 No 5 Sec 5 Xinyi Rd Taipei City 110 Taiwan R O C TEL 886 0 2 27296294 FAX 886 0 2 87862174 China Office Room 807 Area C Xinxin Jingdi Building Jiahe Rd Huli Xiamen 361009 China TEL 86 0 592 5236752 FAX 886 0 592 5281985 Company Website www scglock com Customer Service service sun castle net 886 0 800 629 136
Download Pdf Manuals
Related Search