Home

Futura Manual

Contents

1. C yam SH ME gt O Fig 36 Fig 37 20 Copyright Silca 2015 Operating manual FUTURA 5 1 4 Cutting cruciform keys with 3 fins The standard 4 sided clamp can be used to cut almost all cruciform keys except for Y and T shaped ones 1 Leave the gauge in its original position 2 Fit the key into the clamp Insert the grooved bar into the notch on the clamp according to the key stop as shown in Fig 38 Key stop towards the inner part of the clamp Fig 39 Key stop DOWN and Fig 40 Key stop UP Butt the key stop up against the bar 3 Tighten the knob M1 to secure the key 4 Remove the bar ATTENTION the cuts on each fin are different POSITION OF KEY AND BAR Fig 39 Key stop DOWN Fig 40 Key stop UP Copyright Silca 2015 21 Operating manual FUTURA 5 1 5 Removing fitting the clamp 01V 01VJ Raise the safety shield 2 Unscrew the knob M1 and remove together with the washer set Fig 41 3 Pull the clamp upwards
2. Fig 46 SHOULDER STOP f Fig 47 TIP STOP 5 2 3 TRACK type keys Futura NA Futura Auto Ca Fig 49 Ford Escape key on Futura NA and Futura Auto 24 Copyright Silca 2015 Operating manual FUTURA 5 3 REMOVING FITTING CLAMP 01R Raise the safety shield Loosen the grub screw P2 and remove the clamp by pulling it towards the operator Carefully clean the clamp support seat Clean the clamp before fitting into the support Fit the clamp with knob on the right into the special dovetail and take up against the stop pin Tighten the grub screw P2 to secure the clamp 5 4 REMOVING FITTING THE JAWS ON CLAMP 01R Raise the safety shield Loosen the knob P1 by a couple of turns Fig 51 Use your fingers to pull the jaw to be removed out towards the operator Fig 52 Carefully clean the seat of the jaw on the clamp Clean the jaw before fitting into the clamp 6 Fit the jaw up against the stop pin oF Go N gt NOTE there is only one way to fit the jaw into the clamp Fig 51 Fi
3. Laser receiver Laser transmitter 8 2 12 15 10 OPTIC READER 13 9 2nd version 11 8 9 7 7 gt 6 5 5 3 4 1 1 MOTHER BOARD J9 Laser receiver Laser transmitter 16 4 14 3 12 1 10 2 36 Copyright Silca 2015 Operating manual MOTHER BOARD J12 MOTHER BOARD J15 MOTHER BOARD J17 a FUTURA STEP MOTOR X AXIS red 4 light blue 3 green 2 MOTHER BOARD J13 yellow 1 STEP MOTOR Y AXIS red Al white red 3 gree
4. Zero points X Y Z 174 199 28 Options Machine maintenance Network setting Start Upgrades Backup Restore User series Machine zero points Dimple Track Machine zero points Dimple Track Clamp 01R 01J 02J Side A Tracer 02T Clean carefully the clamp and the tracer Totally close the clamp START Cancel 32 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA Machine zero points Dimple Track ATTENTION Attention This operation will delete any clamp calibrations of Standard key Remember to calibrate again the clamps of Standard keys Machine zero points Dimple Track Machine zero points detected Offset X 175 Offset Y 199 Offset Z 27 Save the calibration At the end of the operation you are required to save the data entered Tap Yes to confirm NOTE Remember to replace the 02T tracer with the proper cutter prior to attempting to cut a key to prevent damaging the 02T tracer Copyright Silca 2015 33 SW SOFTWARE Operating Guide FUTURA 6 3 3 Options The Options menu contains General Preferences STANDARD key Preferences DIMPLE TRACK key 6 3 3 a General The following parameters can be modified e Measurement Unit millimeters or inches Silca Futura_bbl7 fol Info Zero point Calibration neen Measurement Measurement Unit Standard key Unit Calibration Preferences Zero point Calibration Standard key Lang
5. Copyright Silca 2015 63 SW SOFTWARE Operating Guide Tap on Downloads Ka Fig 13 ax kW F F _ B F AW leet 64 SW idav 10 72 de EN Ui 24 Friday 24 October 7014 Silca Futura_bbe3 Ka Lem em H d od Owner r f WW A ECH Ps Copyright Silca 2015 it ZER VI Wegen AN mes Ela Store TE FUTURA SOFTWARE Operating Guide Select Silca apk and tap on Install Fig 14 Wait for the update to finish Futura Do you want to install an update to this existing application Your existing data will not be lost The updated application will get access to DEVICE ACCESS full network access view network connections view Wi Fi connections Cancel Install Fig 14 Do the same for upgrading the SilcaKeyboard apk Copyright Silca 2015 FUTURA 65 SW SOFTWARE Operating Guide FUTURA 8 BACKUP RECOVERY This function permits to create and save a backup backup User database file in a USB key that can be connected the machine s USB port Also provided is the recovery Restore User database function always using the USB key with the last file that was saved on tt Silca Futura_bb17 fal Info User Database Backup Recovery Calibration Settings Backup User Database Restore User Database Maintenance Upgrades User seres 66 SW Copyright Silca 2015 SOFTWARE Operating Gu
6. an a go n ooo 2 MOTOR 1 MOTOR 2 MOTOR 3 MOTOR 4 1 OAL E ul Rios R98 o D ppoppog J5 USB Oo OUTPUTS D T D0 uu 0 D J23 Oo goo00O0 OO pp Wi J20 1 1 1 ARAARA MILLING MOTOR INPUTS 24V 4 J13 X axis motor J12 X axis sensor d J14 Y axis motor J15 Y axis sensor gt J18 Z axis motor J17 Z axis sensor gt J19 not used J16 not used gt J7 cutter motors micro carter lt uod u1 y Ef lt BUUSIUE gf lt uod qsn gr Deen jou ozr SS p sn ou Cen lt a Abt Ajddns 1 mod pf 35 Copyright Silca 2015 Operating manual FUTURA 15 10 OPTIC READER 13 S 1st version 11 8 9 D 7 6 5 5 3 4 1 1 1 2 I 3 4 i I 5 S ZZ i MOTHER 9 10 1
7. Display SSV SERV z Senured with WPANPAZ Storage SSV WibOx e Ca Battery Eso with APA WFAZ Open the drop down menu and select Connect to Machine IP Address Reset Axes Machine Status Change Keyboard E Man Machine Registration Update Futura Hit Start search in the window that appears 46 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA Search the machine in the Network Set the number of Machines in the network 0 all 1 SCH Start search Stop search Hit the description Silca Futura on the screen to connect to the Silca apk APP connection Search the machine in the Network Silca Futurabb17 Set the number of Machines in the network 0 all 1 o Start search Stop search Copyright Silca 2015 47 SW SOFTWARE Operating Guide FUTURA 6 4 MACHINE MAINTENANCE e Digital Inputs This function is used to test operation of the digital inputs on the electronic board to which they are connected screen micro gauge position sensor electrical contact etc To perform the test carry out the movement described for each item and check that the relative signal changes color from red to green Silca Futura_bb17 fal Digital inputs info A Main board temperature Calibration Digital Outputs Micro cover seni wee Open and close the cover DN Optical Reader Micro mobile Tracer position Connections Raise and lower the Tracer
8. Reload page Pete creer Ve Bari ees oe red eect Restart Machine Machine IP Address Reser Axes D399 Machine Status Change Keyboard Machine Registration Update Futura Canlas iiia iE Ti Regmirgtuen eter cepted Recovery tools Gikea APP Vers 120 Arie Copyright Silca 2015 61 SW SOFTWARE Operating Guide FUTURA Take the Tablet where there is a Wi Fi network connect the Tablet to the Wi Fi network and start the Silca FUTURA application On the Tablet scroll from left to right to open the drop down menu d Ceci Ak Connect to Reload page Please wait reloading page Restart Machine Machine IP Address Reset Axes Machine Status Change Keyboard Machine Registration Recovery tools Sica APP Vers 1 20 Tap Update Futura to see a screen showing machine information Tap Check updates and wait a few minutes Connect to See Update Futura Reload page Machine Info Getting machine informations Bootloader 1 0 Restart Machine Keel Microcontroller 1 2 Machine IP Address Operative System 12 Application 28 90 Reset Aves Software 114 Dodd Microcontroller Eat Datatase 1 40 Machine Status Code list 1 39 Check updates Im lay Change Keyboard d Upgrade level and 6 0 password Machine Registration Mastercode 1 0 0 0 Board ID nag Serial Number 1111111111111 MAC Address OKZ FROG KA Recovery tools Silca APP
9. Serial Number Please register on line the machine To register the machine go to menu Options gt Registration e Ifthe machine is not registered now the same message will appear every time FUTURA is started e If the machine is not registered it will not be possible to download software updates There are 4 ways to register Method 1 FUTURA machine and Tablet connected in local Wi Fi network mode or FUTURA machine in Access Point mode connected to the router by Ethernet cable Method 2 FUTURAmachine and Tablet connected in Access Point mode take the Tablet where it can be Wi Fi connected Method 3 Use the Silca Remote Service program SRS Method 4 Registration through browser from a PC Tablet connected to the internet 52 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA Method 1 FUTURA machine and Tablet connected in local Wi Fi network mode or FUTURA machine in Access Point mode connected to the router by Ethernet cable Tap to view the registration method for Futura machines Start the FUTURA program tap the icon OPTIONS gt Settings gt Registration Enter the data into the fields shown those with are required and then tap Register and wait for a message communicating that the machine has been registered Tap Close penal Number il Wating for Email confirmation To complete the registration s requimed to confirm the recemed Email and inte Zero oomt Calibration Standa
10. an Ethernet cable is not connected to the machine port Connect the USB cable to the machine and tablet Access Settings on the tablet by selecting the corresponding icon in the list of applications Set OFF to disable the Wi Fi In the tablet Settings hit the More icon and select the item Tethering amp Portable hotspot DA Settings WIRELESS amp HETWORKS Wireless amp networks e wir Oo Gaston Aeroplane mode a Data usage Tethering amp portable hotspot DEVICE Digital Media Server Sound Share meda wi other eves Display PlayTo Lanes ln A ree ply e Storage gapi Settings WIRELESS amp NETWORKS i Wireless amp networks Tethering amp portable hotspot WiFi OFF USE tetherin d Bluetooth Tethered a Data usage Portable Wi Fi hotspot BE sic DEVICE Mr ASUS Wi Pe portable AF holepet O Sound Display Bluetooth tethering Alot sharing fee lobes inene borreri E Storane Tick USB Tethering or select ON to enable 44 SW SA Copyright Silca 2015 SOFTWARE Operating Guide FUTURA When this item is enabled a green light on the machine will flash for a few seconds It may take 10 20 seconds for this to happen Start the Silca Futura application and open the drop down menu Select Connect to to find the machine A Gi Arak Reload page Please wait reloading page Restart Machine Mach
11. to confirm 26 SW Copyright Silca 2015 SOFTWARE Operating Guide 6 2 2 DIMPLE TRACK keys clamp calibration FUTURA This menu contains a list of standard clamps and options for cutting these types of keys Select the required clamp and tap START to begin calibration Use the 02T tracer for calibrating the clamps ATTENTION to calibrate clamps with J jaws make sure the jaws are closed completely before proceeding Silca Futura_bbe3 Info Clamps Standard keys O1R 01J 02J EE O1R 01J 04J 01R 03J 02J Settings Mobile Tracer 0O1R 05 06 Mai Standard key Adapter Maintenance Standard key Adapte 01R 07J 08 Upgrades Dimple track key Adapter O1R 09J 10J OIR 115 02 Backup Restore O1R 12J5 02J 1 13 02 User series O1R 135 02 O1R 14J 15J O1R 16J 17J O1R 18J 02 O1R 19 02J O1R 20J 21J Silca Futura_bbe3 Clamp Clamp calibrated v z Cancel Info Clamps Standard keys Tracer Clamp side Settings Mobile Tracer Offset X e Wire Maintenance Standard key Adapter Oliset Y Offset Z Upgrades Dimple track key Adapter Backup Restore User senes Copyright Silca 2015 Clamp side A Manual Corrections Offset X D Hf Di bi Offset Y EEE Offset Z kees S ke X e g GH 3e SEH Z 27 SW SOFTWARE Operating Guide FUTURA Calibration Clamp 01R 01J 02J Calibration completed Offset X 0 Offset Y 0 Offset Z 0 undefined At the
12. Calibration Check for new upgrades Settings Maintenance Backup Restore User series Fig 7 Tap on Check for Updates to get a list of what will be downloaded with the update Gm Software Upgrade a Info i A new SW Upgrade ts available News Calibration N 2 components to be upgraded Settings They will be updated Futura application 2 9 0 Maintenance Update level and password 18 0 men Do you want to download the Software Upgrade User series Fig 8 Tap News to see information about the update to be installed on the machine Tap on Yes to start downloading Copyright Silca 2015 59 SW SOFTWARE Operating Guide FUTURA BS A Gica F mura biz WS Updates Calibration Check for new upgrades Settings e Waintenance Backup Restate si Downloading upgrade in progress Liner saries Fig 9 When download is over you will be asked to restart the FUTURA machine procedure run by the software Follow the on screen instructions 7 2 2 Update with SILCA REMOTE SERVICE Program Fig 5 Install the Silca Remote Service program on your PC The program can be downloaded from the Silca website www silca biz by selecting the Products menu gt Silca Key Programs gt SKP Modules gt Silca Remote Service Products 2 Silca Key Programs O SKP Modules Silca Remote Service Z Silca Remote Service Utility for updating programs on b
13. FUTURA FUTURA NA FUTURA JAPAM FUTURA FUTURA Operating Manual Original Instructions D443236XA C vers 7 0 EN CED c 2015 SILCA S p A Vittorio Veneto This manual has been drawn up by SILCA S p A All rights reserved No part of this publication can be reproduced or circulated by any means whatsoever photocopies microfilm or other without the consent of SILCA S p A Edition October 2015 Printed at Vittorio Veneto Da SILCA S p A Via Podgora 20 Z I 31029 VITTORIO VENETO TV Italy The Manufacturer declines any responsibility for possible inaccuracies in this document due to printing or transcription errors The Manufacturer reserves the rights to alter the information without prior notice except when they affect safety This document or any of its parts cannot be copied altered or reproduced without written authorization from the Manufacturer Keep the manual and look after it for the entire life cycle of the machine The information has been drawn up by the manufacturer in his own language Italian to provide users with the necessary indications to use the key cutting machine independently economically and safely IMPORTANT NOTE in compliance with current regulations relating to industrial property we hereby state that the trade marks or trade names mentioned in our documentation are the exclusive property of authorized manufacturers of locks and users Said trade marks or trade names are n
14. Menu used to set up the machine 6 Upgrades Menu used to update machine software 7 Backup Recovery Menu used to save machine data and restore them when necessary 8 Info Menu showing machine details from the search menu Silca Futura_bbe3 Machine ID shows the name of the Futura machine Initial menu tap the symbol to go back to the initial menu Favourites tap the symbol to view the data cards series saved in the favorites menu Copy by Original tap the symbol for direct access to the Copy from Original menu Search menu tap the symbol for direct access to the Search menu Information tap the symbol to view information about the Futura machine iS Bere Turn off machine tap the symbol to turn off the Futura machine without affecting the software wait until the green light goes out and then turn off the machine with the ON Emergency push button Copyright Silca 2015 SOFTWARE Operating Guide e CHOICE OF KEYBOARD FUTURA When the FUTURA program is started you are required to choose the type of keyboard you will use for entering data SILCA Keyboard smaller keyboard specially designed for the FUTURA program Android AOSP keyboard standard Android Tablet keyboard Choose input method English UK Silca Keyboard English UK Android keyboard AOSP Set up input methods If you have chosen the Silca keyboard you can go back to Android by hitting the key on the Silc
15. Micro gauge position Upgrades Backup Restore Log Files Raise and lower the key gauge User series Advanced Setting Electric contact Make a contact between cutter tracer and clamp e Digital Outputs This function is used to test operation of the digital outputs on the electronic board and relative devices connected to it To perform the test tap ON on the screen Silca Futura_bb17 e into Digital Inputs ON Turn on white LED ee Wad ii E Settings Motors ON Turn on greeen LED Turn on blue LED st e ON Tum on Buzzer Upgrades Connectior Backup Restore Log Files Advanced Setting User series 48 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA e Motors This function is used to test operation of the 3 step motors for the X Y and Z axes at the moment the B axis is not used To perform the test tap for the axis involved Note The carriage must not reach and hit the end of its run The Reset key homes the axes NOTE tap only when the value shown in the Working position field is positive Axis clearance sensor the ring becomes green when activated e Cutter motors To perform the test tap the button for the motor to be tested check that the cutter turns for 5 seconds Ine Cigital Inputs Motors Calibration Digital Outputs Motor i z setings Motors Abas luis positian D 0 Oo Work position D Al Al Deotva Reader 5 Tero Ada b
16. VIA PODGORA 20 Z I 31029 VITTORIO VENETO TV ITALY TEL 04389136 FAX 0438 913800 Declares under its own responsibility that the Key cutting machine model FUTURA complies with the requirements of the following European Directives European Union DIRECTIVE 2006 42 CE Machines European Union DIRECTIVE 2004 108 CE Electromagnetic Compatibility European Union DIRECTIVE 1999 5 CE R amp TTE European Union DIRECTIVE 2006 95 CE Low Voltage 14 and with the EN 55022 2010 ETSI EN 300 328 2012 V1 8 1 EN 55024 2010 EN 60825 1 2007 EN 61000 3 2 2006 Al A2 2009 EN 62471 2008 EN 61000 3 3 2008 EN 60950 1 2006 A11 2009 A1 2010 A12 2011 EN 301 489 1 2011 V1 9 2 EN ISO 12100 2010 EN 301 489 17 2012 V2 2 1 EN 62233 2008 Standards Claudio Tomasella of the Silca S p A Research amp Development Division is authorized to create a Technical File General Manager Basic Production Center Stefano Setti 3 ips Pre Pr P fe e EF Wire ra E Fal Pay iting nie EC Drees deier KA SILCA S p A Tel 39 0438 9136 Fax 39 0438 913800 www silca it info silca it Via Podgora 20 Z 1 P IVA C F e Reg Impr IT03286730266 REA TV 258111 wa 31029 Vittorio Veneto TV Italy Cap Soc 10 000 000 i v Export TV 038851 Societ soggetta a direzione coordinamento di Kaba Holding AG con sede in R mlang Svizzera A Member of the Kaba Group Hofwisenstrasse 24 ai sensi e per gli ef
17. 5V TT wie o USB DM reen MOTHER BOARD J5 USB DP black GND USB SHIELD 6 Copyright Silca 2015 39 Operating manual MOTHER BOARD J7 OOA Go h 3 MOTHER BOARD J4 rosso nero rosso nero nero nero Filter FUTURA CUTTER MOTOR MICRO CARTER nr Cutter motor laser ur Cutter motor flat Micro carter red red POWER SUPPLY 24V MOTHER black black 7 lt 24V lt 7 EMERGENCY PUSH BUTTON a f BOARD J3 ETHERNET CABLE EXTENSION 40 Copyright Silca 2015 ETHERNET PORT 4 ETHERNET CABLE Operating manual J2 J3 J4 J5 J6 J7 J8 J9 J10 J12 J13 J14 J15 J16 J17 J18 J19 J20 J21 J22 J23 EN Led lamp Ethernet port Power feeder 24V USB port Antenna Cutter motor micro carter Led lamp RGB Optic reader Gauge sensor X axis sensor X axis motor Y axis motor Y axis sensor not used Z axis sensor Z axis motor not used not used Electric contact Micro cover tracer point s
18. Cuts Decoding Partial cuts mis Card options bei Use corrections Info Card Offset X 5 Offset Y fio Queue of job Note Save Close Manual corrections Warning Do you confirm saving data ATTENTION remember that non suitable corrections may lead to serious damages for the machine ECH wes Confirm with Save 14 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA e PARTIAL CUTS used to make a search for correspondence with the code table if applicable enter the known cuts and tap Search Partial Cuts Code Symbols Cuts Decoding Manual corrections Quantity 1 Card options 1 1 Info Card 1 Queue of job Cutting Tree Note Cutting tree function accessible only from Partial cuts and enabled only for Data cards Series with code tables available Tap the Cutting Tree key to continue Cutting Tree N key blanks required 4 Codes selected Key n 1 The list of keys shown in the cutting tree coincides with the list of keys shown in the Partial cuts window however here the keys are listed according to Groups Code and Cuts in order to reduce to a minimum the number of key blanks to be used The box at the top of the screen shows the maximum number of key blanks to be used for all the possible cut combinations listed Each Group needs a new key blank to cover all the cut combinations it lists work down from
19. Profile Series Makes Applications and Key blank Tap Next to continue Sea Fu era bbed a User series AE Typo of koy DimpeTrack Rey Webiches Keys emm Card 232 Sorita A1 01 180 SE R File Wmportrg praced wre Profile An e Enter the card number genie dezcrmoten ante protien the table to be mmiponed and press Mext io go on to he Asse MEKI Bore hh Curbs Numero imag 68 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA wia Fa bieg A User series E Blakes Ayataka Wakes geeried SHE d DAM E SS File Impaning Drocechuue SICMA ge ge SGelec Ge or mare makes Mam those availabe SIERAU and uae he arrows bo rave Tem ite the r t hangd Column Presse Next To ga on to Mie next Screen SIEM SILCA SIMECA SIMPLEX SINJET SIPEA GIS SrkecaFu ueea Dei LA User series 1 Ap pics Available Apolicaiions Seeche PUCH E RIZZATO CYCLES foot SWM e Lee ihe arrows bo move ihe Gtpoalcatonz mito the right hand column and then press Mert io go op fo ihe neri Pile paring procedure Select ane or mare gopleations fram hose availabe TESTI YAMAHA CYCLES CYLINDERS VARIOUS MAKES Screen CISA PADLOCKS FILLERCAP VARIOUS BRANDS FUIRNMITIIRE FARIS wea Fra bieg A User series A8 Blanks Available Blanks Selected File impaoning praced ire Enter ihe mame of the blank iit apolicaile
20. To view information about the tokens available used tap Taken stat Token available Ela Token consumed D To view the days still available in the case Of her Umimited Tokena P UTPs tap e Duration eratptbel l Expiration days 25 Close Copyright Silca 2015 73 SW SOFTWARE Operating Guide FUTURA e When the icon Token and or calendar UTP are pce it means that the tokens or days are in excess of the minimum warning point in the Token gt Settings menu e When the icon Token and or calendar are yellow it means that the tokens or days are below the minimum warning point in the Token gt Settings menu e When the icon Token and or calendar are red it means that the tokens or days have expired or are about to expire Extratoken If the customer has used up all the tokens or the UTPs have expired SILCA provides the opportunity to cut keys for another 21 days The tokens consumed will be counted during this period A the end of the 21 days the machine will cease to cut keys and a new UTP package or tokens must be purchased from a SILCA distributor If the customer purchases a pack of tokens those consumed during the ExtraToken period will be deducted Example Days 1 Tokens Tokens consumed in the Extra Token period 280 Package purchased 1500 tokens When the package is installed the machine will have 1220 tokens at its disposal If
21. AND CONDITIONS How to Apply These Terms to Your New Programs If you develop a new program and you want it to be of the greatest possible use to the public the best way to achieve this is to make it free software which everyone can redistribute and change under these terms To do so attach the following notices to the program It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty and each file should have at least the copyright line and a pointer to where the full notice is found lt one line to give the program s name and a brief idea of what it does gt Copyright C lt year gt lt name of author gt This program is free software you can redistribute it and or modify it under the terms of the GNU General Public License as published by the Free Software Foundation either version 2 of the License or at your option any later version This program is distributed in the hope that it will be useful but WITHOUT ANY WARRANTY without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE See the GNU General Public License for more details You should have received a copy of the GNU General Public License along with this program if not write to the Free Software Foundation Inc 51 Franklin Street Fifth Floor Boston MA 02110 1301 USA Also add information on how to contact you by electronic and paper mail If the program is interactive make
22. Backup Restore Side B Side C Side D Side F Side H User series Manual Corrections Offset X Offset Y Tap START to begin calibration Fit template Z3 into the 01V clamp as illustrated Standard key clamp calibration ATTENTION Clamp Clamp side Stop Cutter Template Clean carefully the Optical Reader Cancel Copyright Silca 2015 25 SW SOFTWARE Operating Guide FUTURA When the message Clean carefully the Optic Reader and key without removing it appears lift the safety shield and carry out the required operations Close the safety shield and press START to continue Standard key clamp calibration Start Please clean carefully the Optical Reader and the key without removing it gt START E STOP At the end of the operation you are required to save the data entered Tap Yes to confirm Standard key clamp calibration Calibration completed Offset X 8 Offset Y 6 Optical reader Offset X 3 Optical Reader Offset Y 2 Salvare i valori The 01V clamp is calibrated only for Side A Only Manual corrections of Y spaces e X depth can be entered on sides B C and D Positive value of Y takes cut closer to stop Negative value of Y takes cut away from stop Positive value of X lowers the cut from the axis Negative value of X raises the cut from the axis Adjustments from 30 to 30 hundredths of mm 118 thousandths of an inch Tap Save
23. Copy key with measurements read after decoding a key the cuts can be verified and compared to the keys original cuts If the cuts Offset values are significant it s possible to cut the key by using the measurements just read not the keys original cuts nominal values that are in the card by inserting a check flag in the appropriate box NOTE when decoding standard keys you must use the clamp side designated by the software as well as the stop position designated in order to decode the key properly Use of other clamp positions or stop positions will result in a misread key Once decoded should you receive the message key blank not allowed or bad permutation the key may not have been positioned properly As a result the software will not recognize the key blank or the depths read will not correspond with any of the codes in the code series database If you are sure that the proper card and key blank were used reposition your key and try again Copyright Silca 2015 13 SW SOFTWARE Operating Guide FUTURA e MANUAL CORRECTIONS to enter manual adjustments in the relative fields for X axis and Y axis activate the Use corrections flag tap Save and then Close Adjustments from 30 to 30 hundredths of mm 118 thousanaths of an inch Close the window after it has shown an OK message An icon Manualcorrections Indicates when the manual adjustment is active Manual corrections Code
24. Fig 42 4 Carefully clean the seat of the clamp support Clean the clamp before fitting into the support Tighten the knob M1 with the washer set 22 Copyright Silca 2015 Operating manual FUTURA 5 2 CLAMP FOR DIMPLE AND TRACK KEYS 01R According to the type of key to be decoded and or cut follow the instructions in the Silca tablet program regarding e clamp e use of jaws Q1 and Q2 e clamp stop Fig 44 and Fig 45 FITTING THE KEY The clamp is designed to house high security keys with shoulder stop or tip reference For shoulder stop keys place the shoulder of the key against the jaws stop O Fig 44 and the others tip stop must be placed against one of the grooves 1 2 3 4 as indicated in the Silca tablet program For this operation use the bar provided Fig 45 NOTE the stop bar must be removed before decoding or cutting 1 Fit the key to be cut into its seat and ensure it is resting firmly on the clamp plate 2 Tighten the knob M to secure the key 5 2 1 DIMPLE keys A a Fig 44 SHOULDER STOP Fig 45 TIP STOP Copyright Silca 2015 23 Operating manual FUTURA 5 2 2 TRACK type keys
25. Installation is the customer s task and does not require any special skills The key cutting machine is supplied ready for use and does not need calibration except for the tools to be used and any additional jaws that are included with the machine however the operator is required to make certain checks and prepare the machine for use NOTE the machine is shipped with a steel rod installed in the cutter shaft to prevent the allen screw from backing out during transit REMOVE THE ROD AND INSTALL THE PROPER CUTTER PRIOR TO ATTEMPTING TO CUTA KEY 3 1 CHECKING FOR DAMAGE FUTURA is a solid compact machine and will not break if handling unpacking and installation are carried out to the instructions in this manual However it is good practice to check that the machine has not been damaged 3 2 ENVIRONMENTAL CONDITIONS To make the most of the key cutting machine bear in mind the following environmental parameters it is advisable for the area to be dry with good air circulation The optimum environmental conditions for machine operation are temperature 10 C to 40 C relative humidity approx 60 3 3 POSITIONING 1 Place the key cutting machine on a solid horizontal work bench suitable for the weight of the machine 20 Kg The work bench should be approximately 100 120 cm high to facilitate access to the working parts We recommend leaving at least 30 cm clearance behind and around the machine to ensure good ventilation and facilit
26. SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA 11 1 TOKEN APPLICATION ON THE MACHINE TOKENS on the machine can be updated in the ways described below e Futura machine with Local Network LAN connection Select the Update menu in the Futura program and press Check Updates If the Silca server has tokens ordered available a message will appear with a request to download The tokens will be downloaded automatically to the machine without the need to re boot When the tokens have been updated a message will appear to indicate whether a machine software update is available on the Silca Server e Futura machine with ACCESS POINT connection Use the SILCA REMOTE SERVICE program or take your tablet to a Wi Fi connection point with access to the internet If an update is available on the Silca server the tokens ordered available and the machine software update will be downloaded together in a single operation 11 2COPY BY ORIGINAL AND DATA CARD CUTTING FLOW on Token version Before each cutting operation by data card by code or from an original the tablet shows the cost or token value of the chosen cutting operation This information is not visible if a UTP package is used e COPY BY ORIGINAL Clamp side Gutier DIE Clean carefully the Optical Reader CH e COPYING BY CARD Cut Dimple Track key Card 1572 Sn 621 Clamp O1R O1J 02J Camp side A Cut
27. Silca is the default icon for viewing Silca series E tap User to view the existing user series Ch 9 associated to the selected card e Tap the special field to enter the Hook position it is automatically saved when the keyboard is turned oft There are 3 folders on the right of the screen INFORMATION shows information about the lock make applications and Silca IIco key blank Info about a key can be viewed by tapping the field relating to the key blank APPLICATIONS shows the applications for which this key blank is used ete ratte E Ee locks cylinders vehicle model etc Cylinders ABUS EC 75 30 ABB EC 75 40 ABB2 CARD shows information relating to accessories needed for cutting keys with INFORMATION APPLICATIONS the FUTURA key cutting machine Clamg Part Nunther 1 A ae SForR Right Jaw Part Mumiber 1 mu 07432547B Copyright Silca 2015 9 SW SOFTWARE Operating Guide FUTURA KEY BLANK To gain access to additional information regarding the Silca key blank simply tap on the following icon BE e List of other Silca key blanks that can be used e List of comparative key blanks e List of Brand names linked to the Silca key blank Key blanks CS206 Key Manufac SILCA Stem length 2700 Q PPLICATIONS CARD Comparatives Lock Manufacturer ULO50 ABI LL DROE ULO501 ULOSOH LL DON CS206B2 Close 10 SW Copyright Silca 2015 SOFTWARE Op
28. axis carriage U Zaxis carriage V Ethernet port W Power pack W1 Power pack connector Fig 6 Y USB port Z Tool holder Copyright Silca 2015 1 2 SAFETY FUTURA is entirely built in compliance to the Machine Directives The operations for which it has been designed are easily carried out with no risk to the operator The adoption of general safety precautions and observation of the instructions provided by the manufacturer in this manual eliminate all human error unless deliberate FUTURA is designed with features which make it completely safe e Safety shield The protective shield is designed to cover the working parts as completely as possible ensuring operator safety The shield C must be raised in order to fit keys for cutting or carry out other operations Fig 7 Raising the shield by means of a microswitch will deactivate the operating and movement functions including the cutter and failed shield closing will be notified with a special message on the tablet To re activate the work cycle lower the shield and follow the instructions on the tablet Fig 7 e Emergency stop Use the red emergency button R Fig 5 located on the right hand side of the machine to stop the machine immediately in the event of serious malfunctioning or a hazard for the operator When the cause of the emergency has been eliminated turn the button 45 clockwise to deactivate it NOTE the operator is responsi
29. end of the operation you are required to save the data entered Tap Yes to confirm MANUAL CORRECTIONS Y X and Z axis manual corrections can be applied if necessary Positive value of Y takes cut closer to stop Negative value of Y takes cut away from stop Positive value of X moves cut to the right of the axis Negative value of X moves cut to the left of the axis Positive value of Z lowers the cut from the axis Negative value of Z raises the cut from the axis Adjustments from 30 to 30 hundredths of mm 118 thousandths of an inch Tap Save to confirm 6 2 3 MOBILE TRACER 01T calibration ATTENTION when calibrating the 01T mobile tracer make sure the J1 J2 jaws are completely closed before proceeding Silca Futura_bbl7 Info Clamps Standard keys S Cancel Clamps Dimple track keys Mobile Tracer w calibrated Offset X Maintenance Standard key Adapter Offset Y Upgrades Dimple track key Adapter Backup Restore User senes Lower the 01T mobile tracer and lock in place by turning the knurled knob clockwise Tap START to begin calibration and follow the instructions on the screen At the end of the operation you are required to save the data entered Tap YES to confirm 28 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA 6 2 4 STANDARD key Adapter calibration Silca Futura_bbe3 ft Info Clamps Standard keys Bo Simpiex DIV EZ Clamps Dimple t
30. it output a short notice like this when it starts in an interactive mode Gnomovision version 69 Copyright C year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY for details type show w This is free software and you are welcome to redistribute it under certain conditions type show c for details The hypothetical commands show w and show c should show the appropriate parts of the General Public License Of course the commands you use may be called something other than show w and show c they could even be mouse clicks or menu items whatever suits your program You should also get your employer if you work as a programmer or your school if any to sign a copyright disclaimer for the program if necessary Here is a sample alter the names Yoyodyne Inc hereby disclaims all copyright interest in the program Gnomovision which makes passes at compilers written by James Hacker lt signature of Ty Coon gt 1 April 1989 Ty Coon President of Vice This General Public License does not permit incorporating your program into proprietary programs If your program is a subroutine library you may consider it more useful to permit linking proprietary applications with the library If this is what you want to do use the GNU Lesser General Public License instead of this License Copyright Silca 2015 85 SW VITTORIO VENETO 04 03 20 CE DECLARATION OEMA HINE COMPLIANCE SILCA S p A
31. no special hazards involved in moving it The packed machine can by carried manually by one person 2 1 PACKING The packing for the FUTURA key cutting machine ensures safe handling of the machine and all its components Packing comprises expanded plastic material wrapped around the machine The robust cardboard box in which it is placed and the nylon wrapping protect the machine even when stored for a long period Fig 9 T Keep dry Handle with care Up The symbols on the outside of the cardboard box give indications for transport A ATTENTION keep the complete packing for future machine transfers 2 2 UNPACKING To remove the machine from its packing 1 Cut the strapping with scissors and remove 2 Open the box carefully without damaging it 3 Free the machine from the protective shells 4 Check the contents of the packing comprised of FUTURA key cutting machine documentation comprising user s manual spare parts sheet specialist guide and warranty tablet tablet stand power lead power pack tool kit fixing bracket 2 3 HANDLING THE MACHINE Once removed from its packing place FUTURA directly on the work bench one person can easily perform this operation ATTENTION lift the machine by holding onto the base Never lift the machine by gripping the clamps levers or other parts 10 Copyright Silca 2015 Operating manual FUTURA 3 MACHINE INSTALLATION AND PREPARATION
32. regulations lay down special methods for disposing of waste Machine FUTURA is not only a durable machine but is also re usable Recycling is a good environmentally friendly practice Packing The FUTURA device is consigned in a cardboard packing box which can be re used if undamaged When it is to be thrown away it is classified as solid urban waste and should be placed in the special paper collecting bins The protective shell containing the machine is in expanded polyethylene classified as SUW and can therefore be placed in an ordinary waste Waste from key cutting Residue deriving from key cutting is classified as special waste but can be included in solid urban waste SUW as metal scourers This waste must be disposed of in the special collection centers according to its classification by current laws in Italy and the European Union If it is contaminated or contains harmful noxious substances which transform the metal residue included in SUW into harmful noxious substances it is included in the lists of the appendices to current regulations in Italy and the European Union for waste disposal INFORMATION TO USERS Under the terms of Directive 2012 19 UE regarding waste from electric and electronic equipment WEEE e The symbol shown above is also attached to equipment and indicates that it has been placed on the market and must be separated and disposed of when no longer wanted including all components sub assemblies and co
33. select the FUTURA machine ATTENTION you need a blank FAT32 format USB PEN Enter the FUTURA machine serial number into the SRS program screen regarding update preparation and then fit a USB PEN into the PC Wait for the update file to be saved on the USB pen If the machine is not registered you will be required to register using the special website page Ensure that the FUTURA machine is off red push button and that the FUTURA app on your tablet is closed Fit the USB PEN into the FUTURA machine USB port on the back of the machine Start the FUTURA machine and wait a few minutes until the white light flashes regularly Remove the USB PEN without turning off the FUTURA machine Wait for FUTURA to re boot blue light flashing regularly Start the Futura APP from your tablet ATTENTION do not unplug or turn off FUTURA during updating 7 2 3 Update from TABLET Fig 6 ATTENTION Make sure there is no USB PEN in the Futura machine USB port during updating This update procedure is employed to update the FUTURA machine using the Tablet after taking the Tablet to a place where there is a Wi Fi network with internet access Before starting check that the machine is registered shown on the Machine Registration screen On the tablet scroll from left to right to open the drop down menu Tap Machine registration to view a screen enter the machine serial number 13 digits and then hit Check Connect to
34. the Program means either the Program or any derivative work under copyright law that is to say a work containing the Program or a portion of it either verbatim or with modifications and or translated into another language Hereinafter translation is included without limitation in the term modification Each licensee is addressed as you Activities other than copying distribution and modification are not covered by this License they are outside its scope The act of running the Program is not restricted and the output from the Program is covered only if its contents constitute a work based on the Program independent of having been made by running the Program Whether that is true depends on what the Program does 1 You may copy and distribute verbatim copies of the Program s source code as you receive it in any medium provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty keep intact all the notices that refer to this License and to the absence of any warranty and give any other recipients of the Program a copy of this License along with the Program Copyright Silca 2015 83 SW SOFTWARE Operating Guide FUTURA You may charge a fee for the physical act of transferring a copy and you may at your option offer warranty protection in exchange for a fee 2 You may modify your copy or copies of the Program or any portion of it thus forming a work
35. you distribute the same sections as part of a whole which is a work based on the Program the distribution of the whole must be on the terms of this License whose permissions for other licensees extend to the entire whole and thus to each and every part regardless of who wrote it Thus it is not the intent of this section to claim rights or contest your rights to work written entirely by you rather the intent is to exercise the right to control the distribution of derivative or collective works based on the Program In addition mere aggregation of another work not based on the Program with the Program or with a work based on the Program on a volume of a storage or distribution medium does not bring the other work under the scope of this License 3 You may copy and distribute the Program or a work based on it under Section 2 in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following a Accompany it with the complete corresponding machine readable source code which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or b Accompany it with a written offer valid for at least three years to give any third party for a charge no more than your cost of physically performing source distribution a complete machine readable copy of the corresponding source code to be distributed under the terms of Sections 1 and 2 abo
36. 2 Cuts Decoding Se Manual corrections Partial cuts Card options Info Card Queue of job Cancel e QUEUE OF JOB If the cut is filled and correct you can save your job in Queue of Job by tapping the following icon the job can then be done afterwards Tap on Queue of Job to display the list of jobs available e DECODING used to decode the cuts on the original key ATTENTION make sure the key to be decoded is clean ATTENTION anodised aluminium dimple laser keys plastic keys or any other key without electrical conductivity CANNOT BE decoded For these types of keys digit the cuts directly or enter the indirect code if the SSN in use allows it Tap Decoding information appears regarding the position of the key in the clamp To continue tap START and perform the operations described on the screen At the end of the operation tap OK Decoding Code Cuts Decoding Clamp Clamp side d i Manual corrections STOP Partial cuts Card options Info Card Queue of job Note 12 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA To view the decoded measurements and the measurements read on the key tap Decoded Values on the bottom of the screen Decoded data 391 Simbol Nominal value 705 510 575 640 575 pory key with measurements read Then tap CUT to cut the key using the combination provided by the previous operation
37. 7285 BK 1 6032 391 5 T200 BL 1 6002 39 j D CYLINDERS VARIOUS MAKES LOCKS VARIOUS MAKES Key blanks CS206 EF E Key Manufacturer SILCA Stem length 2700 To remove a data card in the Favorite s menu tap the relevant star symbol which will go back to white 22 SW f Copyright Silca 2015 SOFTWARE Operating Guide FUTURA 5 QUEUE OF JOBS The Queue of Jobs collects all the jobs the keys the user prefers to do later See on page 12 how to move a job in this Queue of Jobs key pamez Status T 15 391 7326 1 Axis O 2 6 4 3 5 Queued 0 1 p gt go vu 29 7281 Axis 0 6 2 4 7 3 Stopped 1 2 bk bi e To cut the key select only one job at a time by inserting a check flag in the appropriate box then tap on the arrow symbol to gain access to the key cutting screen e To select deselect all the jobs saved in the Queue tap a the number of pieces can be edited for all jobs or all jobs can be deleted e To delete a job just tap on the garbage bin or select one or more jobs and then tap on Delete Job e To modify the amount of keys to cut just select a job and then tap on Modify Pieces then type in the amount you intend to cut and tap on Confirm key_name Code gt Note Status Pieces 0 14 391 7281 Axis 0 6 2 4 7 3 Stopped 1 2 p rt 23 SW Copyright Silca 2015 SOFTWARE Operati
38. ER POINT REPLACEMENT esch Raise the safety shield Rotate the cutter shaft G1 by hand and take the grub screw G2 to the front of the machine Use a hex key to loosen the grub screw G2 and remove the tool N Fit the new tool pushing all the way upwards Tighten the grub screw G2 to secure the tool O A e2 TS Le em PH g A CT a ji al a gD rhe Ke EE ON Ee lt ar Fig 64 NOTE the machine is shipped with a steel rod installed in the cutter shaft to prevent the allen screw from backing out during transit REMOVE THE ROD AND INSTALL THE PROPER CUTTER PRIOR TO ATTEMPTING TO CUT A KEY 7 5 TRACER 01T REPLACEMENT esch Raise the safety shield Move the lever J1 to the left to lower the tracer Use a hex key to loosen the grub screw J2 and remove the tracer N Fit the new tracer pushing all the way upwards Tighten the grub screw J2 to secure the tracer o A 30 Copyright Silca 2015 Operating manual FUTURA 7 6 CHECKING AND REPLACING FUSE Fuses should be checked with a tester Oohmmeter multimeter etc as they may appear to be in good condition even when they are electrically faulty Fuses must always be replaced with the same amperage and type rapid or delayed as indicated in this manual FUTURA has 1 fuse 4 Amps delayed Protects the cutters motors and their electronic controls 230V a c T
39. ING SPEED c0ccccccceccceseeceeecccceseeeecsccesseeeeeesceeseeeeeesscceseeeesscceeseeeess 18 2 10 Cutting DIMPLE TRACK TUBULAR keys and CUTTING SPEED ticisiccisssivuntaeusssnnawsiwsncinaniannctsivedinaeuatuthuianidediendsnaannets 19 2 COPT E TE 20 amp FAVORITE Sessenta in scam bbesinaadanaaaboanieasaumbookesentanonanbeabesaunnnteantadiaincdeinubatacesaamposkianninoiads 22 5 GUEURE e 23 0 OF TON ae E E EEE EE E EE EE EE EE EE 24 AE Ch e ME 24 02 CALIBRATION HE 25 6 2 1 STANDARD key clamp Calloranlon E 25 6 2 2 DIMPLE TRACK keys clamp calibration a seesiocaecanttraieastcantmcanccactacesnstuseaveininthiainsoumenvetriueuchieentblnieaaonseeivinuencanst 27 6 2 3 MOBILE TRACER ET E ere on 22indvsccsnecereonescsadtncessttaveuvetssadbrncsisiupabineceheoisd bhabsweenyedesnvaxobleonsdiacendsaaenetedeneecked 28 6 2 4 STANDARD key Adapter calibration 2 02 0 lt s000ss00ssse0ceeseesseesseessceentecensseessaneeensceesersseencessansesenssuossaseenesscevenseres 29 6 2 5 DIMPLE TRACK keys Adapters EE eege 29 63 IN eege 30 6 3 1 Zero point Calibration 3S TANDARD EE 30 6 3 2 Zero point Calibration DIMPLIE TRACK BE 32 Bed Eege 34 Fg SINS EE 34 6 3 3 b Preferences Standard key py sei cereretsrenemnseespatescestecmenia sede caneun emma steeeitraetnnontugawalaponmaaduaeneanenemerens dagemssels amedaresbennliane 36 6 3 3 c Preferences DIMPLE TRACK key eege Ee ENEE 37 Cy LE 38 6 3 4 a ACCESS POINT mode Wi Fi connection between machine and Tabl
40. If the distribution and or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces the original copyright 84 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries so that distribution is permitted only in or among countries not thus excluded In such case this License incorporates the limitation as if written in the body of this License 9 The Free Software Foundation may publish revised and or new versions of the General Public License from time to time Such new versions will be similar in spirit to the present version but may differ in detail to address new problems or concerns Each version is given a distinguishing version number If the Program specifies a version number of this License which applies to it and any later version you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation If the Program does not specify a version number of this License you may choose any version ever published by the Free Software Foundation 10 If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different write to the author to ask for permission For software which is copyrighted by the Free Software Foundation write to the Free
41. Power management Language amp input Et ASUS Customised Setting PERSONAL Afrikaans L ti OFF EE Bahasa Indonesia ei Security Bahasa Melayu Ch Lock screen Backup amp reset e tina Accounts Add account Dansk SYSTEM i Deutsch Deutschland Date amp time A Accessibility Deutsch Liechtenstein i About Deutsch sterreich 4 Scroll and select the desired language i e English United States 5 Select Silca Keyboard if desired 6 Select Display gt Sleep gt Never This will prevent the application from timing out and closing the session 7 To quit ire e For all Silca key cutting machine software functionalities follow the instructions in the SOFTWARE Guide section in this manual e Further instructions are given in the quick guide for the tablet 16 Copyright Silca 2015 Operating manual FUTURA 5 CLAMPS 5 1 CLAMPS FOR FLAT KEYS WITH STANDARD CUTS 01V CLAMP FUTURA FUTURA NA Fig 24 01V clamp 01VJ CLAMP FUTURA JAPAN Gi eee Fig 25 01VJ clamp Copyright Silca 2015 17 Operating manual FUTURA The use of one of the clamp sides is required according to the type of key to be decoded and or cut by copying or by code Fig 24 and Fig 25 Positioning the correct side to be used is quick and easy With the clamp jaws slightly open turn the clamp by hand to position it as required facilitated by a new special alignment syst
42. R YM287T2 2 3 DIMPLE TRACK keys This menu is used to restrict a search to the dimple track category of keys e g CS48 IE15 AB48 No on Futura Auto 2 4 FULL KEY SEARCHING This menu is used to make extended searches not restricted to categories No on Futura Auto The SEARCH menu for VEHICLE keys differs from the others in that it has 4 extra search parameters Vehicle make enter the name of the vehicle manufacturer Model enter the name of the vehicle model Year from enter the year the model first came out Year to enter the year production of the model ceased or leave the field empty 2 5 TRASPONDER GUIDE The Transponder Guide contains all the transponder key copying solutions provided by Silca chap 10 Copyright Silca 2015 SOFTWARE Operating Guide FUTURA See example of STANDARD keys search flow When you enter the STANDARD keys category the following window appears for you to enter the search parameters Key blanks gt Cuts 5 i Key Manufacturer wes d Lock Manufacturer Lock system on Tomm a 2 6 SEARCH Parameters Code enter the indirect key cutting code Card Sn enter the card number or serial number assigned by Silca Key blanks enter the Silca IIlco key blank code or comparative Key manufacturer enter name of key manufacturer Cuts enter number of cuts for the key to be included in the search Lock Manufacturer enter the brand of lock to
43. Software Foundation we sometimes make exceptions for this Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally NO WARRANTY 11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE THERE IS NO WARRANTY FOR THE PROGRAM TO THE EXTENT PERMITTED BY APPLICABLE LAW EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND OR OTHER PARTIES PROVIDE THE PROGRAM AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU SHOULD THE PROGRAM PROVE DEFECTIVE YOU ASSUME THE COST OF ALL NECESSARY SERVICING REPAIR OR CORRECTION 12 INNO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER OR ANY OTHER PARTY WHO MAY MODIFY AND OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE BE LIABLE TO YOU FOR DAMAGES INCLUDING ANY GENERAL SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES END OF TERMS
44. TURA After a key search the key to be duplicated will always with exception be the Silca reference by default ILCO can also be set as a reference by default keys that are not produced by Silca copyright obsolete new keys Silca Futura_bb17 Info Zero point Calibration zeen Standard key Calibration Preferences Zero point Calibration Standard key me siii Preferences intions Dimple Track key Network setting Maintenance Upgrades Backup Restore User seres fi zi Reference Brand Selection Measurement Unit Lanquage ILCO Enabled SILCA display Notes Comparatives Copyright Silca 2015 35 SW SOFTWARE Operating Guide FUTURA 6 3 3 6 Preferences Standard key Info Zero point Calibration General Standard key Set preferences Calibration Cutting check Zero point Calibration Sms Dimple Track key Check installed Key jettings Preferences o lotions Dimple Track key aintenance Minimun distance from STOP 0 50 Network setting Upgrades Backup Restore Rectify key STOP Y User series Enable STOP Rectification DW L Rectification Thickness X Key Stop Height Y Depth H Length L Cutting check in simple terms MACS protection Maximum Adjacent Cut Specification When enabled this function prevents the FUTURA from accepting user input of direct cuts that would result in a combination of cuts not include
45. URA machine and Tablet connected in Access Point mode NOTE the Tablet must be taken where there is a Wi Fi connection with internet access Connect a tablet to your local Wi Fi network and connect to the internet to start the Silca FUTURA app Scroll from left to right to open the drop down menu as shown below K AEAk Connect to Reload page Please wait reloading page Restart Machine Machine IP Address Reset Axes gt gt gt Machine Status Change Keyboard Machine Registration Update Futura Recovery tools Sila APP Yars 120 Tap Machine Registration Connect to Reload page ee a Restart Machine tHiiiittiiti Machine IP Address Reset Axes EEY Machine Status Change Keyboard Machine Registration Update Futura of D i d Hi Repanrien Machis toi egies Recovery tools aT iy Sika APP Wars 120 E Privacy Foto E Seger lf the serial number is not read digit its thirteen numerical characters and press Check Enter the data into the fields shown those with are required then tap Register 54 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA Amessage confirming registration will arrive at the address given Use your mail program to open the e mail from Silca and click on Validating email Email address validation Your email address has not been validated Click on the link be
46. Wars 120 At the end tap Download When the message appears to connect to the machine for update installation go back to the FUTURA machine start the Silca FUTURA application and connect in Access Point mode On the Tablet scroll from left to right to open the menu tap Update Futura and then Apply update Wait a few minutes until a message appears to restart the FUTURA machine procedure run by the software Wait a few minutes for the machine to start then connect to the Tablet when the intermittent blue light begins flashing 62 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA 7 3 APP UPDATE Silca apk and SilcaKeyboard apk After you updated the FUTURA machine s software when the program starts up you may see the following screen indicating that a new version of the Silca apk or SilcaKeyboard apk is avaialble Silca Futura_bbe3 a APP ipdate Available A newer version of the APP is available Silca apk Do you want to download the APP Update Cancel install Fig 10 Tap on Install and proceed with updating the APP Search APP ipdate Available Close the current APP and install the Update touching the icon on the top left corner of the screen or select the Android function Download Upgrades Queue of jobs Fig 11 Close the application that is opened by tapping on and dragging the Futura APP downwards off the screen see Fig 12
47. a keyboard DO EN eo EN Bie ES ECS Bold E K LM N oJ ERS COJ E83 ESI D 1U pa 0 Ead pd A Ti E e CHANGE PROGRAM LANGUAGE The default program language is English To change language go to the Options menu Ch 6 select Settings gt Options gt General gt Language and choose the language you require Info Zero point Calibration General Measurement Standard key Unit Calibration Preferences Preferences Cnnneaietiins Somparatiyv Options Dimple Track key p Maintenance Reference Network setting Upgrades Key Manufacturer Backup Restore User series Zero point Calibration Standard key EA EZ Dimple Track key English Language Eg italiano am German EE French Spanish Dutch E Portuguese ka Czech SS Swedish e MEASURING UNITS All the values given in the program for the technical measurements of keys and clamps are expressed in hundredths of a millimetre default or thousandths of an inch according to the measuring unit chosen from the Options menu Copyright Silca 2015 SOFTWARE Operating Guide FUTURA e DROP DOWN MENU Connect to Reload page Please wait reloading page Restart Machine Machine IP Address Reset Axes gt gt Machine Status Change Keyboard Machine Registration Update Futura Recovery tools Silca APP Vers 1 20 To view this menu on the Tablet scroll from left to right to open the list Connect to used to fi
48. ado Detector eje Z Motor eje Z no utilizado no utilizado Contacto el ctrico Micro carter no utilizado PT L mpada Led Porta ethernet Alimentador 24V Porta USB Antena Motor fresa micro carter L mpada Led RGB Leitor optico Sensor calibre Sensor eixo X Motor eixo X Motor eixo Y Sensor eixo Y n o utilizado Sensor eixo Z Motor eixo Z n o utilizado n o utilizado Contato el trico Micro carter FUTURA NL Led lamp Ethernetpoort Voedingseenheid 24V USB poort Antenne Freesmotor cover micro Led lamp RGB Optische lezer Gauge sensor X as sensor X as motor Y as motor Y as sensor niet gebruikt Z as sensor Z as motor niet gebruikt niet gebruikt Elektrisch contact Cover micro sensor palpador sensor tracer punt n o utilizado niet gebruikt 41 SOFTWARE Operating Guide FUTURA SOFI WA is OPERATING GUIDE Copyright Silca 2015 SOFTWARE Operating Guide FUTURA INDEX 1 FUTURA MODELS GENERAL INFORMATION 3 E E AIA I ether vores iie EE E IENE 4 WE OF EE EE eebe is e CHANGE PROGRAM EAING AGE E 5 MEASURING ER RE 5 8 8 as BONE E EE 6 BFW EE 7 WEE le KOYD isine cnn a n ENA Tn EEEE aA T EE 7 ee NEMCE E 7 29 DIMPLE TRAOK EE 7 24 FULLKEY SEARCHING WE 7 259 TRASPONDER eege geess 7 E Wen 8 27 RN KEE I e EE 9 28 Using a CUTTING DATA Oy 2 EE 11 2 9 CUTTING STANDARD flat keys and CUTT
49. and or track cuts It can cut keys in ferrous materials in general brass silver nickel etc having e Standard cuts e Dimple cuts e Track cuts e Special cuts e g Ford Tibbe with optional accessory e Cuts on tubular keys with optional accessory FUTURA is used to cut the following types of keys Keys with STANDARD CUTS ji Fig 4 ATTENTION Anodised aluminium keys plastic keys or any other key without electrical conductivity CANNOT BE decoded O STANDARD on Futura JAPAN Fig 3 Keys with DIMPLE and or TRACK CUTS STANDARD on Futura NA and Futura Auto Copyright Silca 2015 Operating manual FUTURA 1 1 MAIN OPERATING PARTS BOO OO OON ei ve YVOQOOOOO MOO amp Tablet stand Tablet Safety shield Lamp Cover Prismatic cutter Standard cuts Cutter Dimple Track cuts G1 Cutter shaft Dimple Track cuts H Optic reader Gauge D Gauge sensor J Tracer 01T J1 Tracer movement lever L Tool compartment K Swarf collection tray M Clamp 01V Standard cuts Clamp 01J Futura JAPAN version M1 Clamp knob 01V P Clamp 01R Dimple Track cuts P1 Clamp knob 01R Q1 Left hand jaw nm D OD P Q2 Right hand jaw W H ON Emergency push button S X axis carriage IFA oec T Y
50. ar If the machine has not already been registered enter the data in the relevant fields fields marked are required and then hit Register Amessage will be sent to the given email address to confirm registration Use your mail program to open the email from Silca and click on Validating email Email address validation Your email address has not been validated Click on the link below to validate the email address entered Email to validate sxsss silca it Validating email LE you do not see correctly the email copy and paste the link below into your internet browser www Ssilcawebsw biz Futura confirmEmail dat a MTEIMZE4MTU 1YS 5pdA Email to be validated silca it Pid Berek v z ateg u rg Contact Sach SPA We Podgora 20 Zi S020 Vii Werte TN Inky Tei 30 036 81358 Fax 20 De Oste amai F cvtottat E Sica 2014 Al nigra reserved G 9 ag ei De Aa span The machine is now registered 56 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA Method 4 Registration through browser from a PC tablet connected to the internet Access any browser from your PC or tablet and enter the following address https www silcawebsw biz futura reg index html Select the language in the top right hand corner of the page e C https www sikcawebswhizt Please insert the Serial Number of your machine Serial Number 1111111111111 Check Ent
51. ate handling Fig 10 2 Make sure machine voltage is suitable for the mains supply and that the latter is earthed with a differential switch 3 Connect the power lead power pack to the machine chap 3 4 2 f oa cm Fig 10 Copyright Silca 2015 11 Operating manual FUTURA 3 4 SEPARATE PARTS The machine packing also contains the following components separately packed 3 4 1 Tablet stand and tablet Fig 12 These items are separate from the machine and must be unpacked and installed by the operator in the way described below 1 Remove the 2 items from their packing 2 Loosen the knob on top of the machine cover Fig 13 3 Install the tablet stand so that the special profile fits into the slot on the machine cover Fig 14 4 Screw down and tighten the knob to secure the tablet stand to the cover Fig 15 5 Fit the tablet into its stand Fig 16 6 Connect the tablet USB Micro USB cable to the special receptacle on the tablet and then to the power supply 12 Copyright Silca 2015 Operating manual FUTURA 3 4 2 Power pack and lead Z d d ef ae wf wf a ai We aa Fig 17 Fig 18 Connect FUTURA to the power pack W and connect the latter to the power supply with the power lead W2 3 4 3 Fixing bracket If the ke
52. aterial trimmed by the cutter at each passage example expressed in hundredths of a millimetre Key blank dimension used with the Detect Key blank measurement function 16 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA With keys that have SYMMETRIC CUTS the following window would appear Card options K OO Cut Type M_NORMALE_FLAT_LFD Cutter O1F Clamp 01V Key blank dimension 780 Depth removal step 70 Detect Key blank measurement this function is used to read the measurement of the key blank stem width in order to adapt cutting to the key blank in use If this function is enabled it is automatically applied only to keys with two sides NOTE activating the Detect Key blank measurement allows the user to clamp the key in any jaw position i e clamping the keys profile on side C or D only for standard and NA versions when cutting a key by code Regardless of the jaw position used the stop position designated by the software must be used This function is only available when cutting two sided symmetrical standard keys NOTE when this function is enabled cuts cannot be repeated on a key already cut e INFO CARD views information about the clamp side and stop to be used cutter and key blank Tap the relevant icons D to see images and part code ywa ini 2 391 Code SN 728 Cutter DIE a Key blank CS206 4 Cuts Clamp DIV oO 3 Clamp side B Decoding e
53. ations to activate this method 1 FUTURA CONNECTION TO A Wi Fi ROUTER Pick the network to which you want to connect by tapping the SSID field and then inserting the network s password Tap Save to reboot the machine in Local Network The machine should initially reboot with a flashing white and blue light to then end with two flashing blue lights that indicate the connection to the local network was successful If the inserted password was incorrect the machine would reboot in Access Point mode with an intermitted flashing blue light Local network setting SSID SSv GUEST ra RS Password cosessease Security option WPA2 PSK rr x Local Network mode set successfull Local Network mode set successfull Copyright Silca 2015 41 SW SOFTWARE Operating Guide FUTURA 2 CONNECTING TABLET TO A Wi Fi ROUTER From the Tablet s Settings menu tap on the desired network to connect Settings 4 WIRELESS amp NETWORKS SSv GUEST S D Bluetooth OFF 8 SSV PROD Data usage Secured with WPA WPA2 h More SSV DEVL Secured with WPA WPA DEVICE Silca Futura_bb17 Notin range di Sound i Display Storage o Battery Apps amp Users a Power management e ASUS Customised Setting 3 REBOOTING THE FUTURA S APPS Open the drop down menu and select Connect to Reload page ies tea ieee er n ibration i Standard key Access Point Mode Dimple Trac
54. auge to its original position with the gauge up against the key stop proceed as follows 1 Turn counter clockwise 2 Pull towards the operator and continue to rotate counter clockwise until it comes up against the stop pin 13 3 Release the gauge Copyright Silca 2015 19 Operating manual FUTURA 5 1 2 Stop positions key stop d He NR Un Fa um Fig 33 HEAD STOP Stop 0 Fig 34 TIP STOP IL LC LI 4 e To fit keys with tip stops into the clamps fit the bar provided into the grooves Fig 34 or up against the right hand side of the clamp NOTE the stop bar must be removed before decoding or cutting D ATTENTION it is not necessary to apply force to close the clamp properly 5 1 3 Use of pins CLAMP 01V 01VJ For keys with narrow stems the pins must be placed between the bottom of the clamp and the back of the key so that the key protrudes sufficiently out of the clamp and therefore can be properly read and cut If the key has a narrow stem and is also very thin 2 pins must be used Fig 35 Fig 35 If the original key is broken place a suitable sized pin in the groove of the keys stem so that it is properly held in place and therefore can be copied Fig 36 NOTE use a pin with the same diameter for both decoding and cutting
55. based on the Program and copy and distribute such modifications or work under the terms of Section 1 above provided that you also meet all of these conditions a You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change b You must cause any work that you distribute or publish that in whole or in part contains or is derived from the Program or any part thereof to be licensed as a whole at no charge to all third parties under the terms of this License c If the modified program normally reads commands interactively when run you must cause it when started running for such interactive use in the most ordinary way to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty or else saying that you provide a warranty and that users may redistribute the program under these conditions and telling the user how to view a copy of this License Exception if the Program itself is interactive but does not normally print such an announcement your work based on the Program is not required to print an announcement These requirements apply to the modified work as a whole If identifiable sections of that work are not derived from the Program and can be reasonably considered independent and separate works in themselves then this License and its terms do not apply to those sections when you distribute them as separate works But when
56. be included in the search Lock system enter the name of the lock system Press Clear to delete the entered fields After entering one or more parameters tap the Search button to start the search This operation will show the data relating to the lock systems found and information about the Silca Ilco key blank if applicable Tap on the left hand side of the page to re open the Search Parameters window Copyright Silca 2015 SOFTWARE Operating Guide FUTURA 2 DATA CARD SERIE info silca Futura_bbeS l q INFORMATION APPLICATIONS CARD Lock Manufacturer Favourite Sn Lock System lt Profile Series CISA uw T283 BA 1 0032 a91 Dr JPM o T2084 BB 1 6032 3931 l 5 7285 BRK 1 6032 391 5 T286 BL 1 6032 391 1 5 CYLINDERS VARIOUS MAKES LOGES VARIOUS MAKES d B Next CH g s Key blanks C8206 rls SILCA m can ABI G Stem length reng e 2700 CS206B7 Cas gt CH To access the cutting card select the relevant line and tap the OPEN CUTTING CARD button In the section of the window showingthe search results Favourite Sn Lock System Profile Series Card Type N of cuts e Order searches by tapping the arrow next to the relative fields e Select a series from those shown or search for it on the next pages lt Previous mo V Tap this icon to access the Transponder Guide for vehicle keys Select the Silca or User series al
57. ble for keeping the area around the button clear so that it can be reached as quickly as possible e Laser warning Regulations require that warning label Supplied chap 1 4 in the language to be used be attached to the optical reader as shown in Fig 8 Copyright Silca 2015 Operating manual 1 3 TECHNICAL DATA Electricity supply Cutter motor Standard cuts Cutter motor Dimple Track cuts Prismatic cutter Standard cuts Cutter Dimple cuts Cutter Track cuts Tool speed Movement Clamp 01V for standard cuts Clamp 01VJ Futura JAPAN Clamp 01R for Dimple Track cuts Runs Dimensions Mass Noise level CLASS 1 LASER READER FUTURA Machine 24V d c 2 2 Amp 55W Power pack 90 264V a c 50 60Hz 120W MEANWELL GS120A24 P1M 24V d c 24V d c in HSS super rapid steel coated in HSS Super Rapid steel in HSS Super Rapid steel coated prismatic cutter Standard cuts 1100 rpm cutter Dimple Track cuts 7000 rom on 3 axes with special bushes driven by step motors on rectified roller guides removable with 4 universal sides for holding flat keys vehicle keys and cruciform keys removable with 4 universal sides for holding flat keys MIWA flat keys vehicle keys and cruciform keys removable and provided with interchangeable jaws X axis 30mm Yaxis 50mm Z axis 27 mm width 318 mm depth 413 mm height with tablet and stand 522 mm 340
58. cense or distribute the Program is void and will automatically terminate your rights under this License However parties who have received copies or rights from you under this License will not have their licenses terminated so long as such parties remain in full compliance 5 You are not required to accept this License since you have not signed it However nothing else grants you permission to modify or distribute the Program or its derivative works These actions are prohibited by law if you do not accept this License Therefore by modifying or distributing the Program or any work based on the Program you indicate your acceptance of this License to do so and all its terms and conditions for copying distributing or modifying the Program or works based on it 6 Each time you redistribute the Program or any work based on the Program the recipient automatically receives a license from the original licensor to copy distribute or modify the Program subject to these terms and conditions You may not impose any further restrictions on the recipients exercise of the rights granted herein You are not responsible for enforcing compliance by third parties to this License 7 lf as a consequence of a court judgment or allegation of patent infringement or for any other reason not limited to patent issues conditions are imposed on you whether by court order agreement or otherwise that contradict the conditions of this License they do not excu
59. code copy etc ila Future ize infqrmatians Informations Log Fichier Jetons Full log password OH Etalonnage Configurations Tokens Taken Total Tokens Configurators Log File 2015 06 26 13 54 47 CARD 1572_END 6 1333 2018 08 26 13 43 42 CARD 1572 _EHD 9 1295 SE 2015 06 26 13 40 10 COPY END l EH Waves Ze 2018 08 17 16 40 31 CARD 73 4_END Kail 1406 2015008 17 16 17 51 CARD 7354_END 20 1440 Sauvegarde Reinitial 2018 08 17 16 10 40 CARD 7384 END ell 1440 sation 201 508 04 13 42 27 CARD 1572_END 6 1480 2018 08 09 24 57 COPY END 1497 SUR 2015 08 03 09 24 18 cory END l 1493 seo 2018 07 21 10 15 48 CARD Dap END b 144 2015 07 91 09 50 12 ADD 1500 1500 2018 07 31 09 49 34 ADD 1 50m 0 CH 78 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA 12 CHANGING TABLETS If a new Tablet is to replace the previous one download install the Futura App and the customized Silca Keyboard Proceed as follows 1 Make the Wi Fi Tablet Futura connection see Ch 6 3 4 USE 2 Open the browser CHROME OF the CHROME icon is in the Apps page and enter the following ad dresses 192 168 0 1 Silca apk to download the App 192 168 0 1 SilcaKeyboard apk to download the keyboard EA C 192 168 0 1 SilcaKeyboard ac 0410 Wednesday 10 15 2014 al Copyright Silca 2015 79 SW SOFTWARE Operating Guide 4 Open the Android Download application KH Camera Lanser 5 Tap on the 2 apps
60. d Mot inser Us oroduct Usb manufacturer aiia renne Se Backup Hesione Lag Files User seed Advanced seting e Log Files The Log file is requested by Silca when on board machine software anomalies are encountered This function permits to create and save a log file ona USB key connected to the machine s USB port or directly to Silca s Server with the FUTURA machine connected to a local network Wi fi or LAN cable connection Save machine Log Files into a USB PEN drive int Digital Inputs alibratian Digital Qutputs Save Log Files Settings Mr corz wunnen or ert Upgrades Connections Send machine Log Files fo Servet Send Log Files liser saries Advanced Setting 50 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA e Advanced Setting Function for Silca internal use meai F ura lT gt info Digital Inputs Daraa Calibratean Digital Gutputs nl Settings Mrptorg Dotv al Reader Upgrades Connections Backup lesion Lag Files Lengt soties Copyright Silca 2015 51 SW SOFTWARE Operating Guide FUTURA 7 MACHINE UPDATE AND REGISTRATION 7 1 MACHINE REGISTRATION To download the machine software updates you must be registered on the SILCA WEB FUTURA server This operation is required only on first access From the 2 6 0 version of the program on after cutting at least 50 keys you are required to register the machine on the Silca Web FUTURA server
61. d distribute verbatim copies of this license document but changing it is not allowed Preamble The licenses for most software are designed to take away your freedom to share and change it By contrast the GNU General Public License is intended to guarantee your freedom to share and change free software to make sure the software is free for all its users This General Public License applies to most of the Free Software Foundation s software and to any other program whose authors commit to using it Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead You can apply it to your programs too When we speak of free software we are referring to freedom not price Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software and charge for this service if you wish that you receive source code or can get it if you want it that you can change the software or use pieces of it in new free programs and that you know you can do these things To protect your rights we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights These restrictions translate to certain responsibilities for you if you distribute copies of the software or if you modify it For example if you distribute copies of such a program whether gratis or for a fee you must give the recipients all the rights that you have You
62. d in the data cards Check installed key when enabled this function checks whether the second side of the key is properly aligned in the clamp Any alignment errors taper will be offset This function is used only for keys with cuts on both sides Rectify key STOP when enabled adjusts the key stop as per instructions on the screen Minimum distance from stop the range 50 90 hundredths of a millimeter Y 197 354 thousandths of an Inch L Interval for parameters involved in hundredths of a millimeter X Oe 99 Y 0 400 H 0 400 L 0 500 36 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA 6 3 3 c Preferences DIMPLE TRACK key Silca LFD_b657 e info Zero point Calibration General Standard key Set preferences Calibration Preferences Use mobile Tracer bei Zero point Calibration Standard key Dimple Track key ST RR Carriage speed at rapid 3000 Dmnole Track key Machine mamtenance Network setting Upgrades Backup Restore salva User series Set preferences used to enable or disable the use of the 01T mobile tracer If the field is not selected the 02T tracer is required to be fitted into the shaft for the decoding operations Carriage speed at rapid used to set the carriage speed for rapid movements the pre set value of 3000 is recommended by Silca Copyright Silca 2015 37 SW SOFTWARE Operating Guide FUTURA 6 3 4 USE The FUTURA machine ca
63. during cutting operations e Under no circumstances should compressed air be used to clear the work zone of chippings as this will blow them onto the moving parts e Never use oily products or thinners for cleaning painted surfaces clamps electrical or electronic connections e Make sure the key to be decoded is clean Copyright Silca 2015 27 Operating manual FUTURA 7 MAINTENANCE d ATTENTION for repairs or replacement of parts for maintenance the CE mark is guaranteed only if original spare parts provided by the manufacturer are used The FUTURA key cutting machine does not need special maintenance but it is good practice to check and if necessary replace parts subject to wear cutter tracer point belt Replacement operations are simple and can be performed by the operator iss f ATTENTION to maintain machine efficiency we recommend using protective oil such as ATTENTION DO NOT USE COMPRESSED AIR WD40 or similar to apply to the burnished mechanical parts Make sure the oil does not come into contact with the electronic parts Before performing any type of maintenance checks or replacements read the warnings below e Do not perform any maintenance operations with the machine on e Always disconnect the power lead e Follow the instructions in the manual carefully e Use original spare parts see provided spare parts sheet 7 1 OPERATIONS e Access to rear compartment e Prismatic cutter replacem
64. e 38 Bech LOCAL NETWORK Od Ci sacseeocicciiesccsitiatiantoti otieaadeltncssabaes aceiasicdvewhet sosisdeonnaedentsos nal E eE AAEE a SiE a eR ERA 40 6 9 4 0 TETHERING USB MOJE sirsenis areias aa aiaa i aiara iaaiiai 44 6 3 4 d ETHERNET with connection to LAN and router eege ageet NEEN Ae 46 624 Ee EEN Ce 48 7 MACHINE UPDATE and REGISTRATION EE 52 7 1 MACHINE ER A Let CG 52 7 2 MACHINE SOFTWARE UPDATE enger EEN 58 7 2 1 Update in LOCAL NETWORK mode stesgeeb urgegeeg eege Seege Eege geseet 59 7 2 2 Update with SILCA REMOTE SERVICE Program esccsiasccscccerdes stsansntasscstuseerdintaurdsdsesiandusst ciiadGaecestusdecdesedesiaecavetsd 60 Tao e ANS TOM TABUE sgrin N a E E 61 7 3 APP UPDATE Silca apk and Rene ee E EE 63 o PACKUP FRECV EE 66 T USER EN 67 10 he lee 71 11 TOKEN AND UTP Unlimited Token E EE 73 11 21 TOKEN APPLICATION ON Rer E 75 11 2 COPY BY ORIGINAL AND DATA CARD CUTTING FLOW on Token version sssessssnssssennrnssserrrrresrrnrrrrresrrrereenen 75 12 CRHANGING TABLE TS arusi EE TN 79 13 FUTURA PROCEDURE TO CLEAR CACHE 0 cccccccccccceeeeceeeeeeeeeeeeeeaeeeeaeeeseeeeseeeesaeessaeesaeeesaeeeseeeseeees 82 2 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA 1 FUTURA MODELS GENERAL INFORMATION Futura A machine for cutting decoding keys with standard laser and dimple cuts and cutting by Copy from original of cylinder and automobile keys with standard cuts Futura NA A machine for
65. e Zero point Calibration STANDARD key e Zero point Calibration DIMPLE TRACK key e Options e Network setting 6 3 1 Zero point Calibration STANDARD key Tap START and follow the instructions on the screen Info Clamp DIV Calibration Zero point Calibration Clamp side A Calibrated Yes Options Machine Zero points X Y 97 6 maintenance Network setting Upgrades Backup Restore User series Machine Zeros point of Standard key ATTENTION Clamp Side Stop Cutter Template Clean carefully the Optical Reader Cancel 30 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA Machine Zeros point of Standard key Attention This operation will delete any clamp calibrations of Standard key Remember to calibrate again the clamps Machine Zeros point of Standard key Machine zero points detected Offset X 100 Offset Y 8 Salvare i valori At the end of the operation you are required to save the data entered Tap Yes to confirm Copyright Silca 2015 31 SW SOFTWARE Operating Guide FUTURA 6 3 2 Zero point Calibration DIMPLE TRACK key This operation requires the use of the 02T tracer ATTENTION make sure the jaws are completely closed before starting Tap START and follow the instructions on the screen Dimple k Info Zero point Calibration Standard key Clamp 0IR 01J 02J Calibration alibratio Tracer 02T i
66. e plugged into a main power supply to fully re charge the battery daily 2 Turnon the tablet by holding down the push button B1 Fig 22 holding it down for a few seconds REGULATING TABLET INCLINATION 1 Loosen the knob B2 2 Incline the stand as required 3 Tighten the knob B2 4 1 CHOICE OF LANGUAGE d A 1 Select Settings WIRELESS A HETADAES Silca Futura_bbl 8 Bluetooth ete Silea Futura_b6st CB Data usage Setzer with WEP More Silca Futura_bboa Secured srh WEF DEVICE e S5V PHOG do Sound Secured with WPA x Display Silea Futura_b659 e Seog ed with WEP Storage S5V DEVL P Battery Sep wish WPACARAZ a P Apps 4y GUEST 7 B Users Silca Futura_bbaf Secured with WEF VW E Power management IT Zt Guest e E ASUS Customised Setting Copyright Silca 2015 15 Operating manual FUTURA 2 Scroll up with your finger 3 Select Language amp Input and then Language on the right D Power management ZX ASUS Customised Setting Language PERSONAL English United Kingdom Location access OFF KEYBOARD amp INPUT METHODS Default Di Security English UK ASUS keyboard h Lock screen ASUS keyboard Semer Google Keyboard 7 English UK A Backup amp reset Accounts Google voice typing FO Add account SYSTEM Silca Keyboard i Date amp time SPEECH W Accessibility Voice Search coms Text to speech output CH Settings
67. ed on the vehicle by diagnostics or manual procedure If there is no solution with Silca keys when programming by diagnostics or manual procedure if available the copy must be made from an original key column indicating a Silca key blank complete with transponder or ORIGINAL ae Column indicating a Silca key blank without transponder ELS column indicating a Silca FLIP key blank without transponder Example Fig 15 In this case the user may blue section gt to clone the original key with RW devices use HU101MH use HU101TE or HU101FH with GTI transponder green section gt to programme a key on the vehicle with original diagnostics sd see dealer use HU1011T17 use HU101TE or HU101FH with GTI transponder programmed as ID63 or with T17 transponder Get further details or access manual programming procedures by hitting see Fig 15 PELI Transponder details wm D z KE Vehicle Make H ignition kees SILCA key blank Master Valet FORD AUS D HUT RAH Vehicle Model N al programmable ILCO key blank keys AF FALCON KUTO TRAH Trangpoeorber Eat shell N master keys to be programmed Be i D a D d Programmi Deum device W o Haniel procedure D selected 72 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA 11 TOKEN AND UTP UNLIMITED TOKEN PLAN Token machines are a new pay per use concept applied to Futura machines which employ special toke
68. eibi ai i Upgrades Connections aaa E ee e User series Advanced Seating Cutters Motors e Optical Reader Perform the Optical reader threshold test to verify if the optical reader is active Tapping on the Read laser threshold switches the optical reader from to O inig Drotzal rouge a l Test Optical Reader threshold H CGalke zatpmp Digital Qutguits Settings Moos Upgrades Connections Backup Aestore Lag Files Leer series Advanced Setting Copyright Silca 2015 49 SW SOFTWARE Operating Guide FUTURA Perform the Optical reader threshold test only if encountering anomalies when reading and or decoding keys Thoroughly clean the optical reader s glass close the protective shield Tap on Optical reader calibration the green ball indicates that the optical reader is calibrated the red ball indicates that you must thoroughly clean the optical readers lens and re calibrate the reader ATTENTION after the Optical reader calibration proceed with the machine zero points calibration standard flat keys then with the standard flat keys clamp calibration e Connections This function shows all the machine connections that are available Ssca utura_bbl e WTE mE ine Dotal Inputs WiFi 5 E erat eae E E 00 71 iFi 1921 Calibration Digital Outputs a HODE H Saplings Motors Etnherret Etnerret J aeen LGR STATS wen Ceitical Reader Usb arserte
69. em Fig 26 The 4 sided clamp is used to secure keys firmly up against the back and on the profile To copy keys these can be locked on any of the clamp sides A B C or D the user will decide which side is the most suitable To decode a key you MUST use the clamp designated by the software For code key cutting the choice of clamp to use is established by the software Fig 26 CLAMP ROTATION 18 Copyright Silca 2015 Operating manual FUTURA 5 1 1 Use of the shoulder gauge The gauge is used to position flat cylinder or vehicle keys that call for Stop 0 Fig 33 Fig 31 Pull the gauge gently towards the operator turn clockwise by about 180 and release against the clamp Fit the sample key into the clamp with the stop up against the gauge To align the tip of keys without shoulders use the tip stop bar provided Fig 34 The choice of position 1 2 3 4 depends on the length of the cut NOTE take the gauge back by hand to its original position before starting to read or cut the key Fig 32 For all reading decoding and cutting operations the gauge I must be taken back manually to its original position Fig 32 in this position it covers the sensor 12 which detects it To take the g
70. ensor not used IT lampada led Porta ethernet Alimentatore 24V Porta USB Antenna Motore fresa micro carter Lampada Led RGB Lettore ottico Sensore calibro Sensore asse X Motore asse X Motore asse Y Sensore asse Y non usato Sensore asse Z Motore asse Z non usato non usato Contatto elettrico Micro carter sensore tastatore non usato DE Led Lampe Ethernet Anschluss Speisegerat 24V USB Anschluss Antenne Motor Fr ser Mikro Carter Led Lampe RGB Opticher Leser Lehre F hler Fuhler X Achse Motor X Achse Motor Y Achse Fuhler Y Achse nicht verwendet Fuhler Z Achse Motor Z Achse nicht verwendet nicht verwendet Elektrische Kontakt Mikro Carter Taster F hler nicht verwendet FR Lampe Led Port Ethernet Alimentateur 24V Port USB Antenne Moteur fraise micro carter Lampe Led RGB Lecteur optique Senseur calibre Senseur axe X Moteur axe X Moteur axe Y Senseur axe Y non utilis Senseur axe Z Moteur axe Z non utilis non utilis Contact lectrique Micro carter senseur palpador sensor palpador non utilis Copyright Silca 2015 ES Lampara Led Puerto ethernet Alimentador 24V Puerto USB Antena Motor fresa micro carter L mpara Led RGB Lector optico Detector calibre Detector eje X Motor eje X Motor eje Y Detector eje Y no utiliz
71. ent e Cylindrical cutter and or tracer point replacement e Tracer 01T replacement e Checking and replacing fuse e Battery replacement 7 2 ACCESS TO REAR COMPARTMENT 1 Turn off the key cutting machine and disconnect the power lead 2 Remove the tablet 3 Loosen the 2 screws E1 and the 2 screws E2 4 Rotate the cover towards the front of the machine 28 Copyright Silca 2015 Operating manual FUTURA 7 3 PRISMATIC CUTTER REPLACEMENT esch Raise the safety shield 2 Rotate the cutter by hand to align the cutter slot with the rear slot on the reader stand 3 Insert the pin F1 provided with the machine into the 2 slots 4 Loosen the nut F2 clockwise ATTENTION the thread is to the left 5 Remove the nut pin and cutter 6 Carefully clean the cutter shaft seat and the new cutter 7 Fit the new cutter and align the cutter slot with the rear slot on the reader stand 8 Insert the pin F1 provided with the machine into the 2 slots 9 Tighten the nut F2 counter clockwise Attention the thread is to the left ATTENTION when fitting a new cutter to replace a worn one or when fitting a re sharpened one see ch 5 2 of the Software guide Oem Copyright Silca 2015 29 Operating manual FUTURA 7 4 CYLINDRICAL CUTTER AND OR TRAC
72. er key copying solutions provided by Silca Open the Transponder Guide MENU the search window will appear Enter into the fields the known information about the vehicle or transponder key to view data relating to identification copying storage and the procedures provided by Gilea Eutua Die A gi Wehicle Make Wehicle Motel re VEAF e a FEAF d er blanks sel key Manufacturer Cy Transgondar If Transgender Type hide zbachetg SLES key JEC Sapra SOA PLUS PESTO SPS coed fora PAUL AS TCOFY eopiahles cree Ships only these pragamnieahe mih 3103B8 ues odp meh rarest Pree Sew qgenecablen miy ew EMPTY BHELL only D IMPORTANT e tap the column icon to learn the meaning of each column Silca HU e press the orange arrow gt to make a new search or go back COPT Ra NES EE En d HUTOITIT TIF HU TU RH HULOITE HUTOTFH d GT aa GI Fig 15 Copyright Silca 2015 KR Mi CH B o a ac i INPG j FUTURA 71 SW SOFTWARE Operating Guide FUTURA Select the required car model at the top of the window The bottom part of the window will show detailed information about the different possibilities blue section use one of the Silca keys indicated in the first 3 columns to create a clone of the original transponder key i e a key ready for use green section use one of the Silca keys indicated in the first 3 columns to get a key that can be programm
73. er the machine serial number 13 digits and then hit Check a CB https wew siicawebswhiz fut om Serial Number Registration Machine NOT registered Compar Last Name First Name Address Country 3 Privacy Policy Register Back Enter the data in the fields indicated fields marked are required hit Il agree then Register and wait for the message confirming that the machine has been registered Confirmation of registration will be sent to the email address indicated Use your email program to open the e mail received from Silca and click on Validating email Emal address valdateon Your email address has net been validated Click on the link below to validate the email address entered Email te validate sssss ailea it Validating email If you do net See correctly the email copy and paste the link Belew inte your internet browser hitps few si loowebsw bie Fulura conl iemE mai L datacchHPEIRSEAHMT Oye THH jl seo ye poldsowl pill joel sax pbyhybats AB s aW ivShpdh Email to be validated silca it Emad adcress vabdatec succesfully Contact Saca SEA Vie Podgora 20 Z I 31029 Vitono Veneto TV Italy Fax 635 0438 015000 KAILA Copyright Silca 2015 57 SW SOFTWARE Operating Guide 7 2 MACHINE SOFTWARE UPDATE FUTURA NOTE Silca periodically releases Software and Data Updates for the machine To check fo
74. erating Guide FUTURA 2 8 Using a CUTTING DATA CARD Example Data card for STANDARD keys ARD 39 LOCK SYST Code SN 7281 PROFILE BC CODE SERIES 603 Cuts Decoding dh Manual corrections Zoe ay LI EM aan Partial cuts EE Fee A Info Card Pee Lal Queue of job D oa 2 toar Cancel The screen shows all the technical details relating to the selected cutting card e g Card SN Profile Series Spaces Depth Cutting angle Tap the D Cance key to go back to the previous screen Tap L to edit the way to view depths on the card e Depths referring to the key axis Fig 1 e Depths referring to key back i e the plate bottom of the clamp Fig 2 Note this function is only available for two sided symmetrical keys standard and vehicles 235 235 235 235 235 235 235 300 235 235 235 235 235 235 235 j onic ro Fa Fs tc M En VE a EE ra O CN LU gn vm a ihe i i I LJ ges Ai Quota Grezza 820 Quota Grezza 820 P P Dd pp ee ee ee Pe a IRE HHHH HH H el gt 35 35 3 3 3 3 3 300 325 a e WEE un EE un EE vn EE un EL ara Fig 1 Fig 2 Copyright Silca 2015 11 SW SOFTWARE Operating Guide FUTURA The list on the right contains the functions listed below e CODE enter the indirect code for cutting the key e CUTS this function is used to enter direct cuts CARD 391 LOCK SYST Code SN 7281 PROFILE BC CODE BCA0BE SERIES 1 603
75. fetti degli articoli 2497 2497sexies del Codice Civile SILCA S p A Via Podgora 20 Z I 31029 VITTORIO VENETO TV Tel 0438 9136 Fax 0438 913800 E mail silca silca it www silca biz Members of the Kaba Group amp
76. g 52 Copyright Silca 2015 25 Operating manual FUTURA 5 5 USING TRACER 01T The tracer 01T is used to read decode both dimple and track keys This tracer may or may not be required according to the type of key to be decoded and the dimensions involved ATTENTION Anodised aluminium keys plastic keys or any other key without electrical conductivity CANNOT BE decoded e ACTIVATING THE TRACER 01T Fig 54 To use the tracer move the lever J1 to the left and lower the tracer When the tracer is lowered turn the lever knob clockwise e EXCLUDING THE TRACER 01T Fig 55 Turn the lever knob anticlockwise Take the tracer to the idle position raise the lever J1 and move to the right Fig 54 5 6 TRACER 02T Some applications may require the use of the 02T tracer The 02T tracer when required should be placed into the cutter shaft replacing the cutter Fig 57 Note fit the new tracer pushing all the way upwards Fig 56 NOTE for cutting and or decoding operations with the tracer point 02T the tracer 01T must be in the idle position Fig 55 REPLACE THE 02T TRACER WITH THE REQUIRED CUTTER PRIOR TO ATTEMPTING TO CUT A KEY 26 Copyright Silca 2015 Operating manual FUTURA 6 CLEANING e Keep the operational parts of the machine as clean as possible by brushing away the chippings in areas where they accumulate
77. ges of use handling regulation use and maintenance The materials used in manufacture and the components employed in using FUTURA are not dangerous and ensure that the machine complies to current standards Silca S p A has also experimented and applied numerous technical solutions that allow the key cutting machine to optimize the quality of the cut keys To guarantee maintaining these results over time please follow the instructions below e Observe the procedures described in this manual e Always use Original Silca Tools as they are designed to make the best of FUTURA and provide quality key cutting e Use Silca IIlco key blanks made with top quality materials e Have the key cutting machine checked periodically by an authorized Silca After Sales Service Center list at the end of this manual e Always use Silca Original Spare Parts Beware of imitations NORMAL USE FUTURA is a key cutting machine and must be installed and used according to the rules and specifications established by the manufacturer The FUTURA key cutting machine is designed for use on business or industrial premises e g hardware shops key cutting centers etc Any other use different from that indicated in this manual will cause the forfeiture of all customers rights to make claims on Silca S p A and may be an unknown source of hazard for the operator or third parties iS ATTENTION Negligent use or failure by the operator to observe the ins
78. h STOP 0 Clamp 01V CO Part number D942846ZR Manual corrections En ins Partial cuts e Ok ES emm Card options Info Card Note Sch w Cut Cancel e NOTE when highlighted views data card notes i e further specific information relating to the position of the key or an accessory etc Queue of job Note Copyright Silca 2015 17 SW SOFTWARE Operating Guide FUTURA 2 9 CUTTING STANDARD flat keys and CUTTING SPEED To make a cut on the key tap CUT information is shown about the position of the key in the clamp Cut Standard key Card 391 Sn 7281 CARD 391 SN 7261 CODE Clamp DIV Clamp side B E Cutter DIE Gi STOP 0 Detect Key blank gt ae N measurement Pieces 1 The following can be set 1 Pieces indicates how many keys you wish to cut 2 Cutting speed change by means of the following icons Material Key For hard materials such as steel etc select the left hand icon the carriage will 15 advance more slowly than the default settin Ei For soft materials Such as brass etc select the right hand icon the carriage will advance more quickly than the default setting Thickness Key For very thick keys and or those with a full profile select the left hand icon the number reer wa of passages will be higher than the default setting ii For slimmer keys select the right hand icon the number of passages will be lower than the defa
79. he operator IT IS OBLIGATORY to read the manual carefully before using the machine Readers characteristics This manual must be read and its contents acquired by those who will use it Manufacturer s ID FUTURA has an ID plate located on the back of the machine showing the serial number SILCA SPA VIA PODGORA 20 g 8 31029 VITTORIO V TO manufacturer s TREVISO ITALY cb address Tel 0438 9136 Fax 04306 913800 i e mail infogpsilca it TYPE N MATRICOLA serial No working SERIAL No voltage absorbed current absorbed see chap 8 DECOMMISSIONING How to apply for after sales service Silca provides purchasers of FUTURA with After Sales Service For the total safety of the operator and machine any operation not described in the manual must be carried out by the manufacturer or in the special Service Centers recommended by Silca At the end of the manual there is a list of manufacturers and authorized Service Centre addresses The warranty card attached to the machine covers free repairs or replacement of faulty parts for 24 months from the date of purchase All operations must be agreed by the user with Silca or the Service Center Damage caused by negligence or wrong use of the machine by the user will null the warranty Copyright Silca 2015 Operating manual FUTURA TERMINOLOGY For those inexperienced in the subject of keys and key cutting below is an illustration of the most freq
80. i oren rete ccn eects essere esas ee es oat neces E EEEE E REE 24 5 2 3 TRACK TYPE KEYS FUTURA NA AND FUTURA AUTO 24 59 REMOVING FITTING CLAMP OTR eeegeg eg beesesegege eebe EENE EEE OS NEERA EEEE i 25 54 REMOVING FITTING THE JAWS ON CLAMP OJR gemgtesgegce Eege eseeheed eege ees Seebeeee 25 To US SINGTRACER E 26 S0 TRAGER OZ E 26 Eeer 2 T NAINTENANG EE 28 Tel e NEE 28 122 ACCESS TO REAR COMPAR TIVE RRE 28 7 3 PRISMATIC CUTTER REPLACEMENT aeztassssagiee gssseetigeege ER EES EES SES 29 7 4 CYLINDRICAL CUTTER AND OR TRACER POINT REPLACEMENT sssssoasssessseessssrnrsnnererrrserreennns 30 T9 TRACER OIT REPLACEMENT E 30 720 CHECKING AND REPLACING FUS E eege See 31 7 7 BATTERY FRE PEACE E RE 32 o Bl SAO i Eege 33 EE 34 21 HOW TO REQUEST SERVICE eee eee een meen ee ee ne ee Oe eee ree 34 10 ELECTRICAL DIAGRAMS EE 35 SOFIWARE GUIDE eege 1SW CE DECLARATION Operating manual USE OF THE MANUAL This manual has been drawn up by the Manufacturer and is an integral part of the machine literature The manual gives information that is obligatory for the operator to know and which makes it possible to use the machine safely User s Manual This user s manual is provided because it is essential for proper use and maintenance of the machine The manual must be kept carefully throughout the life of the machine including the decommissioning stage Keep in a dry place close to the machine where it is always to hand for t
81. ide FUTURA 9 USER SERIES Function accessible from Options gt User Series This function is available to the user to import a code table in XML Keso or CSV format associating it to a data card and thereby creating a new user series Use a USB PEN FAT32 format and copy onto it the file or files with the table to be imported Note the file must not be in a folder Insert the USB PEN into the Futura USB port die User series a Galibeatian Laer Senes AA Ere il Settings Maintenance Upgrades Rackup Restore To create the user series tap User Series Management Type of ken User Series D Tap Add Series to import the new file When the User Series exists and is selected highlighted you can Tap the Edit key to vary certain parameters associated to the series Tap the Eliminate key to erase the selected series Copyright Silca 2015 67 SW SOFTWARE Operating Guide FUTURA Jia F a bieg A Type of file EJ mm Fie Wpnportng proce wire insertie USB PEN mita the Futu a machine and press the Rehresh button Select the ype of tile to be mooted cv of xml kean Se lecthe file to import amd press Next io goan io the MEKI Sareen Follow the instructions on the Tablet page During guided import you will be required to enter or select certain parameters to associate to the new series e g Data card number
82. ie s a a aoj oa os oO jaa a Es a D suy S 2 _ a a S ris KI EJ 5 a SO_DEBUG o om ol c6 o UI 2 Cm em DI ES eat ID D oS BE eB coe o US U2 ao SEE SS HERIER Lu osf o u31 U3 O D D D DD D 904d OS Cp C219 c28 DE R152 R158 c23 u30 F L10 cns ae ds a E 2 o ogo o 1 E o ogo o N 1 o ogo o 1 o ong 5 GAUGE SENS SENSOR 1 SENSOR 2 SENSOR 3 8 8 3 o o f l oO UU Eer Eer SWITCH bz u o2o n 1 5 E o on o 1 ES D Dep o
83. ine ID Address Reset Axes Machine Status Change Keyboard Machine Registration Update Futura Recovery tools mia APP Wer 1 2 When the machine has been found hit to select and establish connection Search the machine in the Network Silca Futurabb1 7 Set the number of Machines in the network 0 all 1 E Start search Stop search NOTE if the tablet and machine have been turned off when turning on the USB connection must be made again in the way described above if you wish to work with the Tethering USB mode When the machine tablet connection has been made the tablet Wi Fi connection can be re established if necessary Copyright Silca 2015 45 SW SOFTWARE Operating Guide FUTURA 6 3 4 d ETHERNET with connection to LAN and router This method is used to connect the FUTURA key cutting machine to the LAN by cable in the machine ethernet port and the tablet connected by Access Point ETHERNET with connection to LAN and router After connecting the machine to the router with the ethernet cable connect the tablet to the router only if you need an internet connection for your tablet Select the router from the tablet Settings menu and make the connection Wi Fi He on i SSV DEVL Bwetooth fa a m Data usage Silca Futura_0f92 m Bava smurd wih WEF More Sika Futura_bbez m DEVICE Sane secured wih WER Era Siica Futura_093a D Eent wih AER
84. ive value of Y move cut closer to stop Negative value of Y move cut away from stop Positive value of X lower the cut Negative value of X raise the cut Adjustments admitted 30 to 30 hundredths of a millimetre Press Save to confirm 2 Depth removal step 3 Pieces indicates how many keys will be cut 4 Cutting speed change by means of the following icons Material key For hard materials such as steel etc select the left hand icon the carriage will 1s ez advance more slowly than the default setting aan For soft materials Such as brass etc select the right hand icon the carriage will advance more quickly than the default setting Thickness key For very thick keys and or those with a full profile select the left hand icon the number reer wc of passages will be higher than the default setting For slimmer keys select the right hand icon the number of passages will be lower than the default setting DEFAULT When this icon is enabled highlighted the values set by Silca are applied enzeg Remove the key just read from the clamp and load the key blank to be cut positioning with the same Stop and Clamp Side used during the reading process Tap Copy to start key cutting NOTE the Copy by Original function will cut the key exactly as read if no manual adjustments are made If you are copying a worn key and do not make manual adjustments the cut key will be an exact dup
85. just downloaded for installation Download Sikakeyboard 1 apk ba 19216801 11268 f 1 17 ME Sea 1 ak H EI CN IST 166 0 J55 KE 3665 KE Hon ripnatinabile Im 1S Hon riprestinabile ID IEH 80 SW Futura Do you want to install an update to this existing application Your existing data will not be lost The updated application will get access to DEVICE ACCESS full network access view network connections view Wi Fi connections Cancel Install Copyright Silca 2015 FUTURA SOFTWARE Operating Guide FUTURA After you install the new FUTURA application you should move the Silca FUTURA application icon to the main screen 1 Tap the center bottom Open all Apps screen icon MAYA Be Sie Wednesday 10 15 2014 OEE La gt mver NH No onneeitgn Ne e OOP Feta Mailhie Go to Inbox e 2 Search for Futura icon bag 3 Tap and hold keep pressing the Silca Futura application icon and drag it to the main screen e x Seng E Eie e d ei i i _ Wednesday 10 15 2014 HOEFE 7 81 SW Copyright Silca 2015 SOFTWARE Operating Guide 13 FUTURA PROCEDURE TO CLEAR CACHE FUTURA Clearing the FUTURA application Cache is recommended to improve the performance of the FUTURA APP 1 Entering the Android Tablet Settings D Bluetooth ON Data usage More DEVICE di Sound Zi Display St
86. k key Machine IP Address gu z Options Reg n Reset Axes Machine Status iZero point Calibration Change Keyboard AA3N Machine Registration Update Futura Recovery tools Silca APP Vers 1 20 Tap on Start Search in the following window 42 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA Search the machine in the Network Set the number of Machines in the network 0 all 1 9 Start search Stop search Tap on Silca Futura in the following window to obtain a connection between the Futura s APPS Silca apk and the machine Search the machine in the Network Silca Futurabb17 Set the number of Machines in the network 0 all 1 SCH Start search Stop search The last mode setting will be automatically saved by the machine at each successive reboot if the last set mode was Local Network and this mode is not recognized within a certain time frame the FUTURA will automatically go to Access Point mode Copyright Silca 2015 43 SW SOFTWARE Operating Guide FUTURA 6 3 4 c TETHERING USB mode This method is used to connect the machine to a tablet by means of a USB cable Use the power cable provided with the tablet NOTE this function is active from software version 2 12 0 Attention This control is active and can be selected only if the tablet Wi Fi network is disabled OFF the USB cable is connected to the tablet and machine
87. licate of the original worn key To copy a worn key back to OEM specifications you should use the Search function to identify the card or code series used for the original key Once the proper card is opened select Decoding on the right side of the card menu This will measure the cuts based on the depth data used by the OEM and the software will make adjustments to the depths measured and cut the duplicate key back to OEM specifications Copyright Silca 2015 21 SW SOFTWARE Operating Guide FUTURA 4 FAVORITE S Favourites The FAVORITES menu contains the data cards that have been selected in the Search menu Standard keys Vehicle keys Dimple Track keys Saving data cards to the favorites menu will eliminate the time spent searching for frequently used cards Silca LFD_bosT Look System Profile Series Li 729 Atra Boss 5 6 DAA 000001 348933 2176 5 6 5 6 1284 Opel 2T BW 0001 3679 2200 l HH L T281 AC 1 6037 391 a T286 Al 1 6032 391 5 Erer 012345676 330 N d D Cancel To select data cards to be included in the Favorite s menu tap the star symbol in the first left hand column of the Search menu the symbol will be highlighted in black Silca Futura_bbed q Favourite Sn Lock System Profile Senes Type N of cuts INFORMA TION APPLICATIONS CARD 1 6032 Lock Manufacturer DER BD BIER 491 i 5 Ier ZE 3 CISA GI T283 BA 1 6032 391 i D JPM T1284 BB 1 603 KEN ch
88. low to validate the email address entered Email to validate s x s silca it Validating email YS 5pdA Sun Email to be validated silca it Ei ag resg v tep suECeuluEn Contact Sach SPA Vie Podgora 20 21 21020 Vima Weeer Tv ia Tei 30 156 8158 Fam 339 Cubs hoo amai edicts ita il T Sita 2074 All Ponts reserved BOAO va Ett Asi De Go back to the FUTURA machine and re connect in Access Point mode NOTE when the machine is updated for the first time registration data will be transmitted by the Futura WEB server to the machine Copyright Silca 2015 55 SW SOFTWARE Operating Guide FUTURA Method 3 Using the Silca Remote Service SRS program FUTURA machine and tablet connected in Access Point mode Install the Silca Remote Service program on your PC The program can be downloaded from the Silca website www silca biz by selecting the Products menu gt Silca Key Programs gt SKP Modules gt Silca Remote Service Products 2 Silca Key Programs O SKF Modules Silca Remote Service O Silca Remote Service Utility for updating programs on board devices in the RW copying transponder keys and Optika families Futura and Easy Scan over the Internet Sikca Remote Service Module POF Download Start the program and select the Futura machine model select the Next button and then Register a dedicated web page will appe
89. mm without tablet and stand Kg 20 sound pressure Lp A brass flat keys 72 0 dB A Steel flat keys 74 5 dB A brass dimple keys 70 0 dB A brass track keys 74 0 dB A steel track keys 75 0 dB A e Maximum radiation with safety lock excluded 230 uW e Wave length 790 6 um invisible e Classed to EN 60825 1 2007 Copyright Silca 2015 Operating manual 1 4 ACCESSORIES PROVIDED FUTURA comes with a set of accessories for its operation and maintenance tools hex wrenches Supplied in a special tool kit comprising FUTURA stop bar cutter 01D 2 mm allen key S J e 00 See IN 1 7 mm steel pin tracer point 02T 2 5 mm allen key COC INS 1 2 mm steel pin fresa O1L 3 mm allen key C A O1L INS slanted brush fuses 4 Amp delayed cutter release rod ke 19 mm spanner T allen key 2 5 mm template Z3 regulating key b Uu S K d Futura AUTO O3R clamp D743276ZB 19J jaw D744023ZB 04J jaw D743256ZB adapter B6 D708040ZB Futura AUTO cutter 02L D743671ZB oa Futura NA ganascia 19J D744023ZB Cutters and tracers on machine Separately cutter 01F tracer point 01T fixing bracket Copyright Silca 2015 Operating manual FUTURA 2 HANDLING The FUTURA key cutting machine is easy to handle and there are
90. must make sure that they too receive or can get the source code And you must show them these terms so they know their rights We protect your rights with two steps 1 copyright the software and 2 offer you this license which gives you legal permission to copy distribute and or modify the software Also for each author s protection and ours we want to make certain that everyone understands that there is no warranty for this free software If the software is modified by someone else and passed on we want its recipients to know that what they have is not the original so that any problems introduced by others will not reflect on the original authors reputations Finally any free program is threatened constantly by software patents We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses in effect making the program proprietary To prevent this we have made it clear that any patent must be licensed for everyone s free use or not licensed at all The precise terms and conditions for copying distribution and modification follow GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING DISTRIBUTION AND MODIFICATION 0 This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License The Program below refers to any such program or work and a work based on
91. n 2 MOTHER BOARD J14 white green 4 STEP MOTOR Z AXIS red 4 white red 3 green 2 MOTHER BOARD J18 white green 1 X AXIS SENSOR yellow 1 brown black 2 black ut light blue 3 light blue 4 Y AXIS SENSOR 1 brown lightblue our 4 black H Z AXIS SENSOR i brown am 3 black 5 4 light blue 37 Copyright Silca 2015 Operating manual MOTHER BOARD J22 MOTHER BOARD J2 MOTHER BOARD J8 38 FUTURA TRACER POINT SENSOR black brown O 0 A N light blue SS black MICRO CARTER SE red a a Jh a NS green LED LAMP LED LAMP RGB brown red black ON DARON light blue light blue Copyright Silca 2015 Operating manual FUTURA ELECTRIC CONTACT 1 O MOTHER BOARD J21 O 6 GAUGE SENSOR 1 GI 1 MA 7 MOTHER BOARD J10 Ne OUT 4 4 USB PORT S1 USB l r Sg re
92. n be set up in one of the 4 modes below e ACCESS POINT through Wi Fi e LOCAL NETWORK LAN e TETHERING over USB e ETHERNET with connection to LAN 6 3 4 a ACCESS POINT mode Wi Fi connection between machine and Tablet In this mode the Tablet connects directly to the machine The machine is set on this mode in our workshops ACCESS POINT Info Zeropoint Calibration Standard key Access Point Mode Calibration Access point Mode Feropoint Calibration Dimple Track key Satings j Options Machine maintenance Network setting Local Network Mode Upgrades Local network mode Backup Restore Leer series When the machine and Tablet are switched on the connection automatically activates in around two minutes if not check the Wi Fi connection from your Tablet to see if the machine is included in the Wi Fi networks that are found the FUTURA machine will appear as Silca Futura_ 38 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA Friday 02 28 2014 05 WHRELEES AL HET AOS nN Silca Futura_bblT e 8 Bluetooth OFF Prasen con WEP Data 55 PROD 3 ois Prometta con WEA WPAZ S More SV DEM m Prodetia con APANPAT DEVICE d Sound SSv GUEST e Display Storage E Battery E Apps ZB Users B Power mansgernent E ASUS Customised Setting If it is not connected pick Silca Futura_ and input the password which correspond to the FUTURA machine serial number made u
93. nal and load the key blank to be cut Clamp 01V Clamp side Cutter DIE Stop 0 Cutter entrance before STOP 0 Clean carefully the Optical Reader In the Left hand Part of the screen e Select the clamp side A B C D to be used for reading and cutting the key e Select the type of Stop involved 0 1 2 3 4 in the case of Stop 0 the gauge is used to align the key stop with Stops 1 2 3 4 a bar is used to align the stop with the key tip e he Distance field is used when the stop selected is 1 2 3 4 and there is an indication of the point at which the optic reader will start reading the original key Normally this point equals Stop O which refers to the position of the gauge key stop Range 0 400 hundredths of mm gt insert only NEGATIVE value NOTE clean the optic reader carefully with the brush provided before starting the Copy by Original procedure 20 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA When the key has been read the following can be set Sica Futura_bbed Clam S Clamp Offset DIV x 0 Eh Clamp side A Y vele Cutter OTF Depth removal step Stop 100 Pieces 1 Cutter entrance before STOP 0 Clean carefully the Optical Reader Material Key Z ai ch E PO Thickness Key irman 1 Manual adjustments Manual adjustments can be made to Y and X only if strictly necessary Posit
94. nd the FUTURA machine if there is a LAN connection or Wi Fi Access Point Reload page used to reload the page if it is not properly viewed activated Restart Machine used to restart the machine Machine IP address used to enter the FUTURA IP address manually default is192 168 0 1 Reset Axes used to clear the axes on the FUTURA machine Machine Status used to see connection status between the machine and Tablet Change Keyboard used to select and set the type of keyboard to be used Silca or ASUS keyboard Machine Registration used to register the FUTURA machine when the Tablet is connected to a Wi Fi network with internet access Update FUTURA used to download new updates for the machine when the Tablet is connected to a Wi Fi network with internet access Recovery tools this function is protected by a password and is for the exclusive use of Silca personnel In addition the Silca App version installed on the Tablet is shown below Copyright Silca 2015 SOFTWARE Operating Guide FUTURA 2 SEARCHES When the Searches menu is opened the following window appears Standard keys Vehicles keys Dimple Track keys Full key searching 2 1 STANDARD keys Menu used to make a search restricted to the category flat keys only e g CS207 YA31 ULO5O No on Futura Auto 2 2 VEHICLE keys This menu is used to restrict a search to the category of standard edge cut and track vehicle keys only e g HU66P GT15
95. ng Guide 6 OPTIONS Options contains the following menus e Info e Calibration e Settings e Machine maintenance e Upgrades e Backup Restore e User series Machine data Program name LFD Programs Calibration Settings Mastercode version 1 0 0 0 Maintenance Program Version 1 4 Dimple track key Database 1 02 Upgrades Version Standard key Database version 1 02 Backup Restore Upgrade enabled LD 1 2014 F 1 2014 User series Model Futura Machine ID 0000000000000 Serial Number 1153181282209 Mac Address 00 f1 23 aa bb 18 00 f1 23 aa bb 17 IP Address 192 168 0 1 Hardware Version 2 0 Firmware Version 0 9 Card Info Standard keys cut 14 Dimple track keys cut 6 1 INFO FUTURA This window shows the main data for the FUTURA machine e g SW update version serial number number of keys cut etc 24 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA 6 2 CALIBRATION Calibration includes e Clamp Standard keys e Clamps Dimple Track keys e Mobile Tracer e Standard key Adapter e Dimple Track key Adapter 6 2 1 STANDARD key clamp calibration 3 Silca Futura_bbe3 amp Info Clamps Standard keys D Cancel Cutter DIE Calibration i alibratior Clamps Dimple track keys Tainiplate 73 Clamp calibrated AS Settings Mobile Tracer p Offset X 4 Maintenance Standard key Adapter Offset Y 4 Reader Offset X Upgrades Dimple track key Adapter Reader Offset Y 1
96. ns purchased by the customer as and when needed There are 2 types of tokens Token digital coins whose value decreases every time a copy of a key is made When the tokens are finished new ones must be purchased to continue using the key cutting machine UTP Unlimited Token Plan a special timed digital coin that allows the machine to be used freely i e an unlimited number of keys can be cut for a given period a few months up to a year At the end of the period new tokens must be purchased to continue using the key cutting machine NOTE To apply for token recharge and or a UTP package the machine must be registered to register see chap 7 1 MACHINE REGISTRATION Running Tokens and UTPs The following procedures apply when a newly recharged token or UTP package is used according to the type of system on the machine In use on the machhe New System Duration of the UTP package in use is extended by adding the UTP UTP duration of the new one Token Token The new tokens are added to those already in use UTP Token The tokens will be operative when the UTP package expires Token UTP The tokens will be operative when the UTP package expires About tokens and UTPs One of the following two icons is situated in the top left hand corner close to the SILCA logo The Tokens still available Days of use in the case of UTPs Token summary
97. nsumables that are an integral part of the product e Please contact SILCA S p A or any other subject on the national registers of other countries in the European Union for information about waste disposal systems for the equipment Household waste or of similar origins can be disposed of by the separate urban waste collection system e When purchasing new equipment of an equivalent kind the unwanted equipment can be given back to the dealer The dealer will then contact the authority responsible for collecting it e Separate waste collection of unwanted equipment and its forwarding to treatment recovery and environmentally friendly disposal makes it possible to avoid potential negative effects on the environment and human health and assists recycling and recovery of materials e Unauthorized disposal of the product by the user is punished by the application of fines established by the countries which have received Directive 2009 98 CE wastes are substances or objects deriving from human activity or natural cycles which are discarded or intended to be discarded Copyright Silca 2015 33 Operating manual FUTURA 9 ASSISTANCE Silca provides full assistance to purchasers of the key cutting machine To ensure complete safety for the operator any job not specifi ed in this manual should be carried out by the manufacturer or in the special Service Centres recommended by Silca On the back cover of this manual is a list of the manufac
98. o check and or replace the fuse proceed as follows 1 Turn the machine off and unplug it from its power supply cable 2 Access the rear compartment chap 7 2 To remove the fuse press the fuse cap with your fingers and turn it counter clockwise To fit the new fuse carefully position the fuse back into place then gently press the fuse cap downwards turning it clockwise 2 D To remove CoA To fit Fig 67 Copyright Silca 2015 31 Operating manual FUTURA 7 7 BATTERY REPLACEMENT 1 Turn the machine off and unplug it from its power supply cable 2 Access the rear compartment chap 7 2 3 Use insulated screwdriver to remove the fl at battery 4 Insert the new battery into its seat paying attention to the poles A ATTENTION use the same type of lithium battery CR2032 3 Volt JAMEEL e SEIT si S DEY e gt rea amen j SA T SE 32 Copyright Silca 2015 Operating manual FUTURA 8 DECOMMISSIONING To decommission the machine it must be made unusable by e deactivating the power supply e separating the plastic parts from the metal parts e Remove the lithium battery from the electronic board A ATTENTION the lithium battery must be disposed of in the special containers After doing the above dispose of the waste in compliance with the current directives in the country where the machine is located Waste disposal CEE
99. oard devices in the RW copying transponder keys and Optika families Futura and Easy Scan over the Internet Silca Remote Service Module PDF Download The machine can be updated in the following ways Method 1 Quick update Quick update saves time as it downloads only the files needed Fit a blank format FAT32 USB PEN into the Futura machine and open the machine software go to the Diagnostics menu gt Log File and press Save log file on the USB pen Fit the USB PEN into the PC on which the SRS program is installed go to the SRS program screen regarding quick update preparation and wait for the update file to be saved on the machine If the machine is not registered you will be required to register using the special website page Ensure that the FUTURA machine is off red push button and that the FUTURA app on the tablet is closed Fit the USB PEN into the FUTURA machine USB port at the back of the machine Start the FUTURA machine and wait a few minutes until the white light flashes regularly Remove the USB PEN without turning off the FUTURA machine Wait for FUTURA to re boot blue light flashing regularly Start the Futura APP from your tablet ATTENTION do not unplug or turn off FUTURA during updating 60 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA Method 2 Total update Total update all files will be downloaded a Start the program T sica Remote sevice aNd
100. ominated only for the purposes of information so that any lock for which our keys are made can be rapidly identified INDEX USE OF THE MANUAL EH 1 GENERACE E E 4 1 MACHINE DESCRIP ON WEE 5 E WR MAIN OPERATING RE 6 La AFET EE T t3 TEGHNICAL DATA eonia e ee ee ETTO E ee ee ee RISk 8 NF TR RE 9 SE 10 e lc EE 10 2 Een ce ee ees E A E A ee 10 2 3 HANDLING THE EEN 10 3 MACHINE INSTALLATION AND PREPARATION e erscccctetcccexsistesnenceionsedeensseesstaecenersizetsecevdedwaceucgsdieteseensinciee 11 3 1 CHECKING FOR DAMAGE ert ere tine a erek kada iiair eet ee etre ee eee ee ninini ree 11 32 ENVIRONMENTAL CONDITION escenico i En n ege EE EEEE eE 11 SS SR e TR E 11 SE KE PAR KE 12 3 4 1 TABLET STAND AND TABLET E 12 3 4 2 POWER PACK AND EA 13 SE ING eM EE 13 3 5 WORK STATION DESCRIPTION giessen 14 d TABLET REGULATION AND geet 15 A1 CHOICE OF LANGUAGE gaa a nee E E EE EE OTEA a A EERE 15 SE ee ee E EE E E E E E E O ee eee EEEE O 17 5 1 CLAMPS FOR FLAT KEYS WITH STANDARD CUTS setters eee eee eee 17 511 USE OF THE SRAOULDER Seege eee er ee er ee eee 19 51 2 STOP POSITIONS KEY STOP cee 20 5 1 3 USE OF PINS CLAMP OIVIOINJ e eee e ee eee eee ee eee ee eae ee ead reese essen eeeaae essa eeeeaed 20 5 1 4 e EREECHEN 21 5 1 5 REMOVING FITTING THE CLAMP 01V Ol geegeegtege eege dE 22 5 2 CLAMP FOR DIMPLE AND TRACK KEYS ME Egeter deeg EE 23 oA DIMPLE KEYT eee eer eee enn enn eae enn en eee er ee nme eee ents 23 TLL TRAR KE rene
101. orage os 2 Tap on Apps and then FUTURA di Display Storage DOWNLOADED Batt m Futura e 1 25MB Pm Geen D Users L a Power management ZX ASUS Customised Setting PERSONAL gt oration access B 44 a 4 A a RUNNING 3 Tap on Clear Cache Apps o Futura Version 1 0 Force stop Uninstall P Show notifications STORAGE te 1 EE 1 25MB EE err oe eH Tes A a ee 1 16MB Date EEN 88 00KB Clear data CACHE Cache 10 78MB Clear cache marpa E 82 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA GNU GENERAL PUBLIC LICENSE This product includes partly software owned by Silca and partly open source software Below is the original text of the official license for open source software On request Silca will provide a DVD with the GPL code included in the FUTURA product To make the request contact SILCA at the following address SILCA S p A Via Podgora 20 31020 Vittorio veneto ltaly Email service silca it The GPL code used on this product is distributed WITHOUT A WARRANTY and is subject to copyright for one or more writers This product also includes software developed by OpenSSL Project for use by the OpenSSL Toolkit GNU GENERAL PUBLIC LICENSE Version 2 June 1991 Copyright C 1989 1991 Free Software Foundation Inc 51 Franklin Street Fifth Floor Boston MA 02110 1301 USA Everyone is permitted to copy an
102. p of 13 numbers Silca Futura_bbl Signal strength Excellent Sacunity WER LCE F show password Show adane op ons Cancel RRERERESESKSERKSERWNR e _ SUES eS ee es es EES ESR meme 1 1 1 1 1 1 1 ie mm gen mn Copyright Silca 2015 39 SW SOFTWARE Operating Guide FUTURA The option to change the Wi Fi channel is used in cases when the point to point communication cannot be properly connected since there are too many devices tuned to the same channel lt also permits the user to adapt to the rules and restrictions of Wi Fi channel use in their country To change the channel one must first be connected select the new channel and then reboot the machine Wifi Channel Selection Wifi Channel 6 3 4 5 LOCAL NETWORK mode This mode is used to connect the machine to a Wi Fi router Connect the Tablet to the same router to communicate with the machine LOCAL NETWORK LAN To access this method of use go to the Settings menu on the tablet select Network setting and hit the Local Network mode icon info Fero point Calibration Standard key Access Point Mode Calibration Access point Made Zero point Calibration Dimple Track key Options Machine maintenance Matwork setting Local Network Mode Upgrades Local network mode Backup Restore lear series 40 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA Perform the following oper
103. r new updates use one of the connection methods available ATTENTION Do not insert a USB modem sticks for the transfer of data in the machine USB port FUTURA can be updated in one of the following ways Update with LOCAL NETWORK mode Update with LOCAL NETWORK option Connect the FUTURA machine to the local Wi Fi network Attention first set uo FUTURA and then the Tablet in Local Network mode Connect the FUTURA machine to the LOCAL network inserting the network cable to the machine Ethernet port the machine must remain in Access Point mode Fig 4 Update with SRS Program Silca Remote Service Update from TABLET 1 Use the Silca Remote Service SRS to download the software update from the web 2 Use a USB PEN to transfer the update onto the machine 1 Use the Tablet connected to a Wi Fi network with Internet access to download the software update 2 Connect the Tablet to the machine in ACCESS POINT mode to transfer the update to the machine Fig 5 58 SW Fig 6 Copyright Silca 2015 SOFTWARE Operating Guide FUTURA 7 2 1 Update in LOCAL NETWORK mode Fig 3 Fig 4 ATTENTION Make sure there is no USB PEN in the Futura machine USB port during updating Tap E to view machine update methods To upgrade the FUTURA machines software in manual mode follow the steps indicated below Silca Futura_bb17 Updates i
104. rack keys B14 Esety Omega DIV Settings Mobile Tracer Upgrades Dimple track key Adapter Backup Restore User series Manual Corrections Offset X y Offset Y gt 4 gt X am om gt Adjustments to X spaces and Y depths can be made manually Positive value of Y takes cut closer to stop Negative value of Y takes cut away from stop Positive value of X lowers the cut from the axis Negative value of X raises the cut from the axis Adjustments from 30 to 30 hundredths of mm 118 thousandths of an inch Tap Save to confirm 6 2 5 DIMPLE TRACK keys Adapters calibration Silea Futura_bbi Clamps Standand keys Clamps Dimple track keys A34 01A 01J 024 Settings Mobile Tracer Maintenance Standard key Adapter E Upgrades Dimpleitrack key Adapter Backup Restore EE side A User series Manual Comections Offset X Offset Offset Z Positive value of Y takes cut closer to stop Negative value of Y takes cut away from stop Positive value of X moves cut to the right of the axis Negative value of X moves cut to the left of the axis Positive value of Z lowers the cut from the axis Negative value of Z raises the cut from the axis Adjustments from 30 to 30 hundredths of mm 118 thousandths of an inch Tap Save to confirm Copyright Silca 2015 29 SW SOFTWARE Operating Guide FUTURA 6 3 SETTINGS The Settings menu contains
105. rd key Calibration Zero goint Calibration press the buttan CHECK of thes screen Dimp Track Hey Senial Humber Dotwung kamienice Company Gica Asia TEE Hetwark setting Laat Hame Sieg First Mame Sica Rackiip Aeaiore Address Yia Paipera 120 Leer sapjes ity Vittpro Veneno County if Emai e e pila Required Fields A message confirming registration will arrive at the address given Use your mail program to open the e mail from Silca and click on Validating email Email address validation Your email address has not been validated Click on the link below to validate the email address entered Email to validate xss silca it Validating email If you do not see correctly the email copy and paste the link below into your internet browser https www silcawebsw biz Futura confirmEmail dat a MTE1MZE4MTUyMj IwN jswMDo mMzowN piNjo2MztsaxXZpby5yb3Nz aUBzaWx YS 5pdA Email to be validated silca it Email address validated succesfully Contact Silca S p A Via Podgora 20 Z I 31029 Vittorio Veneto TV Italy Tel 39 0438 9136 Fax 39 0438 913800 e mail info silca it Silca 2014 All rights reserved KABA s Member of the Kaba Group At the end tap Close and then Check to conclude the registration procedure on the Tablet Copyright Silca 2015 53 SW SOFTWARE Operating Guide FUTURA Method 2 FUT
106. ria Gregummp2ie 100 Maintenance Average monthly cansumptan Ap Eniimate Token end days ado Upgrades Token virtual stati Bachupy Restore Annal coneurption 100 Average monthly consumption Ap User series Cost Token by type key Dimple Track kers Siancdarg keyg Vehicles keys Fai Si Real statistics are calculated according to the actual consumption of the tokens purchased when normal tokens are used Virtual statistics calculate average consumption of tokens when a UTP is in use In this way customers can see how much they would have consumed in tokens if they had purchased individual tokens instead of the UTP option Tap Settings to edit the following values e Token alert threshold number indicates the point in numbers of tokens at which special warning messages are activated e UTP threshold alert days indicates the point in number of days at which special warning messages are activated Silea Futira_O9 Be A inio Info Token preferences Calbeaton Token alert threshold jnumber 300 UTP Unlimited Takend Paid threshold ag Sapings alert days Maintenance Upgrades Bachup Resor User series i a Copyright Silca 2015 77 SW SOFTWARE Operating Guide FUTURA Tap Log File to view the last operations carried out by the FUTURA machine and saved in chronological order token recharge tokens consumed by a copy from the original tokens consumed by a data card or
107. se you from the conditions of this License If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations then as a consequence you may not distribute the Program at all For example if a patent license would not permit royalty free redistribution of the Program by all those who receive copies directly or indirectly through you then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program If any portion of this section is held invalid or unenforceable under any particular circumstance the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system it is up to the author donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License 8
108. ta make a search Le the arrows to move ihe banka miia the right hand Column and then press Mert io go anio ihe new sereen 69 SW Copyright Silca 2015 SOFTWARE Operating Guide Sones faz Code import Ah Card 732 File H me imp weh lest CSN s e Operation on data in Up Code ARS IO table Press Refresh to apply editing ARTDI 17434 Separator k ao Skip tal pw o ABIDZ 33437 Symbol separator O ARIA 23437 Quake Hone a 6 ARID 12343 ABTS er2ag4 ABO 127434 A DT 1244s ARTIA 22924 AGT 2492 4B110 22134 Age En fnermateon AKI Guts STM es Tap Import to import the file directly without editing FUTURA Note only if necessary before terminating table import you can edit certain parameters using the menu on the right Operation on data in the table and or Operations on columns Tap i to view information about the field After editing the parameters Operation on data in the table tap the Refresh key After editing the parameters Operations on columns tap the Import key to start importing the file At the end of the operations the following screen will appear Import result No errors found Tap Save to save the new User series Tap Modify to make changes 70 SW Copyright Silca 2015 SOFTWARE Operating Guide 10 TRANSPONDER GUIDE Transponder Guide The Transponder Guide contains all the transpond
109. ter iD STOP H Pieces Token required D ao SU Dy 110 Clean the clamp Copyright Silca 2015 75 SW SOFTWARE Operating Guide FUTURA At the end of the Copy by data card or Copy from original flow a window appears on your tablet showing the cost of the operation tokens consumed This information is not visible if a UTP package is used VEL Copy key Ses Clamp Goy ker DIN Liv F Copy completed Clamp side A e Token consumed Press Repeat to cut more capes or sade 2 Additional Token is required for a new copy ce for cutting the second side Cutter DIE Stop Piecas 1 Cutter entrance before STOP 0 Clean carefully the Optical Then required 1 Roader Material Ray Thickness Key H e e Cut Dimple Track key Card 1572 Sn 621 CARD Ei BEEN SH az CODE Cutting completed Cutting completed Humber of keys cut irectiona Token consumed 6 a rn w Ok fl eat CB a E i ES Queue of job e p Mote gt Cancel CH 76 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA Summary of TOKEN or UTP situation In the Options menu of the Silca Futura program tap Token and then Info to view a summary of the data and statistics relating to the token system M info Token avartahle 1440 Calibration Settings Taken consumed 100 Settings Log Files Acte Tobes statistics i S An
110. the American market for cutting decoding keys with standard laser and dimple cuts and cutting by Copy from original of cylinder and automobile keys with standard cuts Futura JAPAN A cutting machine for the Japanese market for cutting decoding keys with standard laser and dimple cuts and cutting by Copy from original of cylinder and automobile keys with standard cuts Futura AUTO Cutting machine for cutting decoding vehicle keys cars motor bikes trucks bicycles and relative accessories etc with standard and laser cuts Cutting by Copy from original of vehicle keys with standard cuts TOKEN Futura chap 11 Pay per use key cutting machine run on tokens Nota please check with Silca whether the token option is available on the version you require Copyright Silca 2015 SOFTWARE Operating Guide FUTURA e PROGRAM START To start the program tap the icon Ge on the Tablet screen lf the program does not start check the network settings use see Ch 6 3 4 Silca Futura_bbe3 Queue of obs Keen Lg e J AN e D 1 Search Menu used to select a category of Series Searches 2 Copy by Original Menu used to make a copy of a key by means of a laser reader standard edge cut keys only 3 Favourites Menu used to access a series of searches previously set up as favourites 4 Queue of jobs Menu used to run the job queue previously created 5 Options
111. the customer purchases a UTP package the days used during the ExtraToken period will be deducted according to the following logic the last day on which key cutting took place is counted Examples X one or more keys cut 1 2 3 4 5 6 aE 9 10 11 12 13 14 15 Nk 18 19 20 21 One day will be deducted from the duration of the UTP package in question 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 10 days will be deducted from the duration of the UTP package in question Ee 20 days will be deducted from the duration of the UTP package in question TATA ee EA Ad No days will be deducted Note Futura Token is sold without tokens When the first key is cut a UTP is automatically activated free for one month At the end of the month you will be informed on your tablet that you have 3 weeks 21 days your disposal to purchase the token solution that meets your needs according to calculations regarding use of the machine At the end of the 3 week period the machine will no longer cut keys To continue using the machine contact a Silca distributor to purchase tokens or UTPs and set up the machine for the chosen mode Tokens or UTPs 74
112. top Select the group and or single code and tap the QUEUE key to place them in the job queue Tap Close OK and then Queue of Job The jobs must be carried out in progressive order starting from the key with the shallowest cuts to those with deeper cuts Copyright Silca 2015 15 SW SOFTWARE Operating Guide FUTURA e CARD OPTIONS Code Card options Cuts D Decoding Cut Type M_NORMALE_FLAT_LFD Cutter ot Manual corrections Clamp 01V Partial cuts Key blank dimension 780 Depth removal step 70 Info Card Queue of job Note Cut type alternative cutting methods can be chosen from Flat Track Normal Normal Easy y t NORMAL M_NORMALE_FLAT LFD For conventional car and door keys y t FLAT M_PIANO_FLAT_LFD put into the lock Mainly used for car keys where the cut edges are rounded to facilitate the movement of the blades when the key is D e LASER M_LASER_FLAT_LFD Conjunction of the cutting angles is determined automati NV 7 cally by the machine allowing cuts to be made with varia ble angles this facilitates the smooth entry of the key into the lock prolonging the working life of the key y t NORMAL EASY M_EASY_FLAT_LFD Concerns traditional automotive and door lock keys the edges of the cuts are removed when possible by a defi ned value of around 30 hundredths of a millimeter Likewi se even for the keys tip Depth removal step this value indicates the amount of m
113. tructions in this manual are not covered by the warranty and the manufacturer declines any responsibility in such cases ATTENTION Anodised aluminium keys plastic keys or any other key without electrical conductivity CANNOT BE decoded RESIDUAL RISKS No further risks will arise when properly using the FUTURA machine SAFETY REGULATIONS e Always disconnect the machine when it is not in use or when performing maintenance operations e Check the electrical wiring periodically replace any wires that show signs of wear e Always work with dry hands free of grease or oil e Never tug on the electricity supply lead and make sure it is not in contact with oil or other liquids sharp objects or heat Never remove the grounding pin from the plug Check that the ground wire is connected properly e Do not use the machine in dangerous environments wet or damp e All visitors especially children must stay at a safe distance from the machine and must never come into contact with the electric wiring Copyright Silca 2015 Operating manual FUTURA 1 MACHINE DESCRIPTION FUTURA is an electronic machine operating on 3 axes with controlled movement Accurately studied it adds a high degree of cutting precision to operating speed and ease of use FUTURA operates only when connected to a TABLET containing a Silca program It uses a laser reader to read and or codify flat keys with standard cuts It uses a tracer to decode keys with dimple
114. turer s addresses listed below are the addresses of specialized Service Centers 9 1 HOW TO REQUEST SERVICE The guarantee attached to the key cutting machines ensures free repairs or replacements of faulty parts within 24 months of purchase All other service calls must be arranged by the customer with Silca or with a Silca service center 34 Copyright Silca 2015 FUTURA Operating manual 10 ELECTRICAL DIAGRAMS JOSUas Julod 13981 Jeueo oU Zeer e due Dei zr gt JOB U0D 91149819 LZ gt GOu due pe or gt Josuas o6neb our gt Be O Wl Bn O Q O O wel 93020 ROL d0 pe naan il o Oo Oo o O8Oo OOo 2 ER ES s Oje Oj Opez le 2 2f r Gi o a B g al 1 R129 lt bg ea onan o 7 HE D z m zB fe 3 ES H SSC Han E Lo D ez lt x a oO aen Gr Dozy O o S zen ajsa T E3 S a el o dot N sno sco meai Sa Tee EIS Per S TL EEE N o dpe RES 2 all 2 5 D lt o KG eil Sjj H a u rE OI s
115. uage Dimple Track key Hundredths of a Millimeter OTT Preferences Comparatives Options Dimple Track key Thousandths of Inch Maintenance R eter ence Network setting Key Manufacturer Upgrades Backup Restore User series Silca Futura_bb17 fal Info Zero point Calibration aen Measurement Language Standard key Unit Calibration Preferences Zero point Calibration Standard key ER Dimple Track key Settings Preferences c e Somparatives Optior Dimple Track key p gg italiano Maintenance Reference Network setting mm German Upgrades Key Manufacturer EE French Backup Restore Spanish User series Dutch Gg Portuguese ka Czech SS Swedish 34 SW Copyright Silca 2015 SOFTWARE Operating Guide e Comparatives comparative brands to visualize for key research It s possible to pick and or unpick brands that can be seen after a research of comparatives articles In the comparative list Silca is activated by default Silea Futura_bbl Standard key Calibration Preferences Zero point Calibration Standard key senna Ge 2ethngs Preferences Dimple Track key Maintenance Network setting Upgrades Backup Restore User series e Reference Key Manufacturer Comparatives Measurement F S Um Language Enabled display Notes Reference Key Manufacture IR CLOVER SILGA STAR TAYLOR Select All Deselect All FU
116. uently used terms Fig 2 1 Head 4 Blade stem 7 STANDARD cutting 10 Stem 2 Neck 5 Tip 8 DIMPLE cutting 3 Shoulder stop 6 Back 9 TRACK cutting ATTENTION anodised aluminium dimple laser keys plastic keys or any other key without electrical conductivity CANNOT BE decoded For these types of keys digit the cuts directly or enter the indirect code if the SSN in use allows it 2 Copyright Silca 2015 Operating manual FUTURA GRAPHICS IN THE MANUAL Obligation to read OP aerch Symbol on Pay attention the manual TOKEN versions GRAPHICS ON THE FUTURA KEY CUTTING MACHINE T Do not clean with Obligation to read OE code Symbol on compressed air the manual TOKEN versions P E ane Laser warning labels A QR code is a two dimensional bar code used to memorize information to be read by means of a mobile phone or smart phone Read the QR code on the machine to connect to useful and constantly updated information relating to key cutting machine maintenance useful tips for your FUTURA key cutting machine and see the continuously evolving range of optional accessories Get the free mobile app at http gettag mobi Copyright Silca 2015 gt Operating manual FUTURA GENERAL WARNINGS FUTURA is designed to the principles of European Standards CE Right from the design stage solutions have been adopted to eliminate hazards for the operator in all the sta
117. ult setting DEFAULT When this icon is enabled highlighted the values set by Silca are applied rename 18 SW Copyright Silca 2015 SOFTWARE Operating Guide FUTURA 2 10 Cutting DIMPLE TRACK TUBULAR keys and CUTTING SPEED To make a cut on the key tap CUT 4 i information is shown about the position of the key in the clamp Q Cut Dimple Track key Card 869 Sn 100 CARD 869 SN 100 CODE Clamp 01R 01J 02J Clamp side A Cutter 01D STOP 0 Pieces 1 The following can be set 1 Pieces indicates how many keys you wish to cut 2 Cutting speed change relates to carriage advancement NOTE the default value set by Silca is 100 To change the Silca settings tap the required value With a value of 110 the carriages will advance at a speed 10 higher than the default setting With a value of 90 or 80 the carriages will advance 10 or 20 more slowly than the default setting Press START to begin the procedure Copyright Silca 2015 19 SW SOFTWARE Operating Guide FUTURA 3 COPY BY ORIGINAL Copy by Original Tap Copy by Original to start the procedure for copying an original key using the laser reader as an optic reader device This operation can be used only for the types of keys cut on clamp 01V The Copy procedure is divided into two steps first load the original key to be read into the clamp 01V once the key has been read remove the origi
118. ve on a medium customarily used for software interchange or c Accompany it with the information you received as to the offer to distribute corresponding source code This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer in accord with Subsection b above The source code for a work means the preferred form of the work for making modifications to it For an executable work complete source code means all the source code for all modules it contains plus any associated interface definition files plus the scripts used to control compilation and installation of the executable However as a special exception the source code distributed need not include anything that is normally distributed in either source or binary form with the major components compiler Kernel and so on of the operating system on which the executable runs unless that component itself accompanies the executable If distribution of executable or object code is made by offering access to copy from a designated place then offering equivalent access to copy the source code from the same place counts as distribution of the source code even though third parties are not compelled to copy the source along with the object code 4 You may not copy modify sublicense or distribute the Program except as expressly provided under this License Any attempt otherwise to copy modify subli
119. y cutting machine is transported and used on a vehicle e g a van it must be prepared as follows 1 Turn off the machine and detach the power lead 2 Remove the tablet holder and tablet 3 Turn the key cutting machine onto its back 4 Connect the fixing bracket to the machine and secure with the 2 screws 5 Return the machine to its upright position on the work top 13 Copyright Silca 2015 Operating manual FUTURA 3 5 WORK STATION DESCRIPTION One operator is enough to operate the machine which has the following operating parts e General ON OFF emergency button R located on the right hand side of the machine e Key holding clamps M P e Tablet B e Tablet ON button B1 e Safety shield C e Cutters F G B C S EE P gt F S S G M ech 0 i L d EE 4 R Fig 22 14 Copyright Silca 2015 Operating manual FUTURA 4 TABLET REGULATION AND USE 1 Connect the tablet to a power source by means of its power pack in order to charge it 3 hours for the first charge Plugging the tablet into the USB port on the back of the Futura machine will not provide enough power to fully charge the tablet The USB port will provide a trickle charge and may extend the battery life while the tablet is used The tablet should b

Download Pdf Manuals

Related Search

Related Contents

La qualification des intérimaires, une priorité en Picardie  タイドクロック取扱説明書  Philips SC5275/33  MANUAL DE INSTRUCCIONES  Equip USB 2.0 Dual PC Bridge Cable  Philips Marathon Bucket CRP192  Emerson 133HP Drawings & Schematics  Quick Reference Guide  the PDF file  コンプレッサの設置に関する法規  

Copyright © All rights reserved. Failed to retrieve file