LED Realbeam 4 RGBW
Contents
1. Display setting for using the device overhead installed With this function you can set fine the white output fine if you have RGB at 100 Dimmer red 0 10096 Dimmer green 0 100 Dimmer blue 0 10096 With this function you can control the device manual Dimmer red 0 10096 Dimmer green 0 100 Dimmer blue 0 10096 Dimmer white 0 10096 Dimmer 0 10096 Strobe Pan Tilt Test mode Shows the current working hours Shows the current software version Reset 9 16 VARYTEC 6 DMX chart 6 1 DMX Mode 1 1 channel Channel Value from 0 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 58 72 76 80 84 88 92 96 100 104 108 112 116 120 124 128 132 136 140 144 148 152 156 160 Value to 3 7 11 15 19 23 27 31 35 39 43 47 51 55 59 63 67 71 75 79 83 87 91 95 99 103 107 111 115 119 123 127 131 135 139 143 147 151 155 159 163 Function RGBW Red Green Blue Yellow Cyan Magenta White Orange Pink Violet Aqua Sky blue Full white Cool white Warm white White 3200 White 2500 Yellow 2 LEE 101 Straw LEE 103 Orange LEE 105 Light Rose LEE 107 Dark pink LEE 111 Magenta LEE 113 Blue 2 LEE 115 Med blue green LEE 116 Dark blue LEE 119 Bright Pink LEE 128 Medium Blue LEE 132 Golden amber LEE 134 Deep golden amber LEE 135 Pale Lavender LEE 136 Apricot LEE 147 Dark Lavender LEE 180 Chocolate LE2. fire electric shock or crash 4 16 VARYTEC 2 1 Overhead installation Danger of life You have to observe the regulations of BGV C1 formerly VBG 70 and EN60598 2 17 Installations are to carry out by skilled personnel only The suspension devices have to be build and measured so they can withstand for an hour the tenfold of the payload without suffering a permanent detrimental deformation Basically installation has to be made by using a second separate suspension This can be e g a suitable net The second suspension must be designed and attached so no part of the installation can fall down in case of failure During construction reconstruction and deconstruction unnecessary stay in the range of moving areas on lightning bridges under elevated work stations or any other danger zones is forbidden The operator is obliged to following safety related and mechanical facilities Before the first start up or after critical changes before restarting it has to be checked by an expert Review in the frame of the inspection test at least all four years by an expert Review by a qualified person at least once a year How to carry out the overhead installation In tidal fall you should install the device out of the lounge area of people IMPORTANT Overhead installation requires a high level of experience This includes knowledge of calculating the payload used installation material and safety inspections of the used ma
3. VARYTEC Manual LED Realbeam 4 RGBW VARYTEC 1 2 3 4 5 6 T 8 Table of contents Safety INStrUCIONS al 3 1 1 For safe and efficient operation nnne nnne 3 IM apri 4 2 1 Qverhead installat O M ies 5 ATO ARA E TL TREE 7 3 1 PTOQUCTCOVEIVIEW sasssa a aa af aan 7 3 2 DIMENSIONS gs a ra d a 7 CONNECCION 2 8 4 1 Electrical CONNECTIONS iii 8 4 2 UMX CONNECHIONS deckt dena ety uteris ii ha ann a bec a peu eb 8 4 3 DMX connection with nennen nennen nnne nnne nnne 8 Control ai ds 9 5 1 Str cture of the Men isis 9 DMX chait A a nr TIME IE IM 10 6 1 DMX Model 1 chanmel assist eli tices anette ke ale 10 6 2 DMX Mode 2 9 channels en E 11 6 3 DMX Mode 16 12 ISSN 13 Fecinicaldala PTT IEEE 14 2 16 VARYTEC 1 Safety instructions e This device is suitable for indoor use not outdoors only e All modifications to the device will void the warranty e Repairs are t
4. E 156 Just blue LEE 79 Surprise pink LEE 194 Scarlet LEE 24 Surprise Peach LEE 017 Fire LEE 19 English rose LEE 108 10 16 VARYTEC 6 2 DMX Mode 2 9 channels Channel 1 2 3 oN O O1 164 168 172 176 180 184 188 192 196 200 204 209 Value from 167 171 175 179 183 187 191 195 199 203 208 255 Value to 255 255 255 7 15 131 139 181 189 231 239 247 255 255 255 255 255 69 79 89 199 209 239 255 Mauve LEE 126 Bright blue LEE 141 Alice blue ROSCO 378 Rose indigo ROSCO 358 Urban blue ROSCO 81 Cool blue ROSCO 66 Light salmon ROSCO 30 Mayan sun ROSCO 318 Cherry rose ROSCO 332 Flesh pink ROSCO 34 Skelton exotic sangria ROSCO 39 Random color selection Function Pan Tilt 0 100 No function Open Strobe slow fast Open Pulse effect fast close and slow open Open Pulse effect slow close and fast open Open Random strobe Open Dimmer red 0 10096 Dimmer green 0 10096 Dimmer blue 0 100 Dimmer white 0 10096 No function Activates the blackout while Pan Tilt moving Deactivates the blackout while Pan Tilt moving No function Reset No function Sound to Light 11 16 VARYTEC 6 3 DMX Mode 3 16 channels Channel Value from Value to Function 1 0 255 Pan 2 0 255 Pan fine 3 0 255 Tilt 4 0 255 Tilt fine 5 0 255 Speed Pan Tilt fast slow 0 15 No function 16 35 Macro 1 36 55 Macro 2 56 75 Macro 3 76 95 Macro 3 96 115 Macr
5. mages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems Make sure the electrical connection is carried out by qualified personnel All electrical and mechanical connections have to be carried out according to the European safety standards 3 16 AA VARYTEC 2 Designated use This device was developed for professional use on stages in discos theatres etc The device is only approved for a connection up to 230V 50 60 Hz AC voltage and only for indoor use Regular breaks during operation increase the lifetime of your device Avoid convulsions or any form of forceful impact during the installation or the start up of the device Make sure that the device is not exposed excessive heat humidity or dust at the place of installation Take care that no cables are lying around You would endanger your own safety and also the safety of a third party It is not allowed to operate or store the device in an environment in which spray water rain humidity or fog is expected Humidity or very high atmospheric humidity could reduce the isolation of the device and could cause deathly electric shocks If you use fog devices the device has not be exposed to a direct smoke jet There has to be a safety distance of at least 0 5m between this device and the fog machine Make sure that the saturation of the fog has to enable a visibility of at least 10m The ambien
6. o 4 6 116 135 Macro 5 136 155 Macro 6 156 175 Macro 7 176 195 Macro 8 196 215 Macro 9 216 235 Macro 11 236 255 Macro12 7 0 255 Speed macros slow fast 8 0 255 Dimmer 0 10096 0 7 No function 8 15 Open 16 131 Strobe slow fast 132 139 Open 140 181 Pulse effect fast close and slow open 182 189 Open 190 231 Pulse effect slow close and fast open 232 239 Open 240 247 Random strobe 248 255 Open 10 0 255 Dimmer red 0 100 11 0 255 Dimmer green 0 10096 12 0 255 Dimmer blue 0 10096 13 0 255 Dimmer white 0 10096 0 7 No function 14 8 127 32 color macros 128 191 Color change 192 255 Color change fade 15 0 255 Speed color change slow fast 0 69 No function 16 70 79 Activates the blackout while Pan Tilt moving 80 89 Deactivates the blackout while Pan Tilt moving 90 199 No function 12 16 VARYTEC 200 209 Reset 210 239 No function 240 255 Sound to Light T IR remote Power on off Activates DMX Activates Master Slave an Tilt Color fade Activates Sound to Light mode No function Q Eon Choose a program or a setting Activates the automatic mode AN 00060 0 00 Choose a program a setting 000 NIU Color selection 13 16 VARYTEC 8 Technical data Power supply Voltage Power consumption max Light source LM type Color spectrum Power Number Power Optics Beam angle Connections Power in XLR in out Controlling Sound to Light Au
7. o carry out by skilled personnel only e Use only fuses of the same type and original parts as spare parts e Protect the unit from rain and humidity to avoid fire and electric shocks e sure to unplug the power supply before opening the housing 1 1 For safe and efficient operation Be careful with heat and extreme temperature Avoid exposing it to direct rays of the sun or near a heating appliance Not put it in a temperature bellow 32 F 0 C or exceeding 104 40 C Keep away from humidity water and dust Do not place the set in a location with high humidity or lots of dust Containers with water should not be placed on the set Keep away from sources of hum and noise Such as transformer motor tuner TV set and amplifier To avoid placing on un stable location Select a level and stable location to avoid vibration Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust or a wet soft cloth for stubborn dirt If out of work contact sales agency immediately Any troubles arose remove the power plug soon and contact with an engineer for repairing do not open the cabinet by yourself it might result a danger of electric shock Take care with the power cable Never pull the power cable to remove the plug from the receptacle be sure to hold the plug When not using the device for an extended period of time be sure to disconnect the plug from the receptacle Important Da
8. t temperature has to be between 0 C and 40 Avoid direct sunlight and close proximity to heaters You have also to attend it during the transport in closed motor vehicles Operate the device not during thunderstorms Surge voltages could destroy the device Unplug the power supply during thunderstorms During the installation the use of the mounting bracket is obligatory Surrounding objects or surfaces should not be in contact with the device Make sure that during the installation and removal of the device the area below the place of installation is basically cordoned off This also applies to implementation of service The device has basically been protected by a suitable safety Make familiar yourself with the functions of the device before start up People without the experience should not handle with the device The most cause of functional disorder is inappropriate handling Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust or a wet soft cloth for stubborn dirt For transport use the original packing or designated accessory to avoid damages during the transport For reasons of safety unauthorized changes are forbidden A usage of the device which differs from usages which are described in this manual can cause damages of the device In that case the warranty expires Additional you should notice that every differed usage is related with dangers and can cause e g an electrical short
9. terial and the projector whereas the required experience is not limited to this Do not try to carry out installation yourself under any circumstances if you are not qualified Contact a professional installer An inappropriate installation can lead to injuries and or damaged properties It is not allowed to install the device in the grip area of people If the device may hang from the ceiling or from high beams the use of truss systems is mandatory The device may not be installed so it can swing freely in the room Please note Crashing down items can cause serious injuries Do not install the projector if you doubt the safety of a possible installation form Before installation make sure that the mounting surface has the ability to carry the tenfold point load of the own weight of the device Mount the device with the mounting bracket to your trussing system using an appropriate clamp During overhead installation the device must be always secured by a safety rope which is designed to hold the twelvefold weight of device Only safety ropes with quick release safety fastener elements may be used Hang up the safety rope in the hole of the mounting bracket Direct the rope over the truss or an appropriate fastening point Hang up the end in the fastening element and tie up the locking nut A safety rope once exposed to failing load or damaged may not be used furthermore 5 16 VARYTI The maximum drop exceed must not exceed 20cm A safe
10. tomatic Master Slave DMX512 Number of DMX channels Hardware Protection class Suitability Dimensions L B H Weight 110 240 V 50 60 Hz 70W LED 4in1 RGBW 60 W 4x15W YO IEC 3pol Yes Yes Yes Yes 1 9 16 channels IP20 Indoor 234 x 196 x 130 mm 2 8 kg 14 16 15 16 VARYTEC Importer B amp K Braun GmbH Industriestra e 2 D 76307 Karlsbad www bkbraun com info bkbraun com Ce b 16 16 RoHS COMPLIANT 2002 95 EC
11. tput Socket of the last device in the series Please look to the bottom drawings COMMON DMX 0201 zZ Not Used COMMON DMX INPUT DMX OUTPUT DMX 8 16 VARYTEC 5 Control Press MENU to get to the menu With UP DOWN you can choose the required submenu Confirm with ENTER With UP DOWN you can make your required settings Confirm your settings with ENTER By pressing MENU you get back to the main menu 5 1 Structure of the menu Menu Addr Chnd Auto SLnd SoUn SenS bLnd Led Pan Tilt dISP Stat Manu Test Info rest Submenu 1 1 512 1Ch 9Ch 16Ch Ato1 4 SP 1 2 Mast SL1 2 On Off 0 100 Yes No Yes No On Off On Off dISP dSIP red 125 255 Gree 125 255 blue 125 255 red 0 255 Gree 0 255 bLue 0 255 Uhit 0 255 Dimm 0 255 Stro 0 255 Pan 0 255 tilt 0 255 Fhrs 0 255 uer Submenu 2 Function Setting the DMX address Choose one DMX mode Choose one automatic program The device sends a master signal The device acts as slave De Activates the sound to light mode Setting the sensitivity of microphone De Activates the blind function If you choose Yes the LEDs are off if you restart the device If this function is activated the display turns off if there is menu using De Activates the invert Pan De Activates the invert Tilt Display setting for using the device head up
12. ty rope once exposed to failing load or damaged may not be used furthermore Adjust the desired inclination angle via the mounting bracket and tighten the screw 6 16 VARYTEC 3 Introduction Thank you for buying the LED Realbeam 4 RGBW It is a powerful device For a successful installation and operation please read this manual carefully 3 1 Product overview p Am 7 16 VARYTEC 4 Connections 4 1 Electrical connections If you wish to change the power supply settings see the chapter Appendix Connect the fixture to the mains with the enclosed power cable and plug The earth has to be connected Cable EU Cable US Pin International Brown Black Live L Light blue White Neutral N Yellow Green Green Earth 4 2 DMX connections To make a DMX512 connection go ahead like it is described in the picture Make sure that you use shielded cable 3pole or 5pole XLR cables are suitable If you use a controller with a 5 pin DMX output connector you will need to use a 5pin to 3 pin adapter 4 3 DMX connection with terminator Where the DMX cable has to run a long distance or the equipment is operated in an electrically noisy environment like a disco for installations we recommend using a DMX terminator This prevents corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR connector with a 120 O resistor between pins 2 and 3 which is then plugged into the XLR ou
Download Pdf Manuals
Related Search