MPC823E61J13ER Errata
Contents
1. The following table shows the recommended values for the XFC Capacitor for CDR2 MPC823e rev A and later silicon along with the minimum and maximum values as determined by the multiplication factor MF XFC CAPACITOR VALUES MF MINIMUM RECOMMENDED MAXIMUM RANGE CAPACITANCE CAPACITANCE CAPACITANCE UNIT MF lt 4 580 MF 100 680 MF 120 780 MF 140 pF MF gt 4 830 MF 1100 MF 1470 MF pF DOC5 I2C Address Register Not Cleared on Reset The I2C Address Regsiter IZADD is not cleared by reset This may cause a nonzero value to be present on reset If this value matches the address of a slave device on the I2C bus it will cause reception problems over I2C This errata has no other effect on operation Workaround If using I2C Master Mode reset I12ADD to 0x0 during your I2C initialization routine MPC823E DEVICE ERRATA 61J13D 9 MPC823E DEVICE ERRATA 61J13D MOTOROLA MOTOROLA MPC823E DEVICE ERRATA 61J13D 11 HOW TO REACH US USA EUROPE LOCATIONS NOT LISTED Motorola Literature Distribution P O Box 5405 Denver Colorado 80217 1 800 521 6274 or 480 768 2130 JAPAN Motorola Japan Ltd SPS Technical Information Center 3 20 1 Minami Azabu Minato ku Tokyo 106 8573 Japan 81 3 3440 3569 ASIA PACIFIC Motorola Semiconductors H K Ltd Silicon Harbour Centre 2 Dai King Street Tai Po Industrial Estate Tai Po N T Hong Kong 852 26668334 HOME PAGE2. FIELD TIME RES TIMEP DR2M DRIM DRQP EIE SCD ERAM RESET 0 0 0 0 0 0 0 0 0 R W R W R W R W RW RWW R W RW R W R W ADDR IMMR amp OxFFFF0000 0x9c4 BIT 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 FIELD RESERVED ERAM4K RESERVED RESET 0 0 0 R W R W RW RW ADDR IMMR amp OxFFFF0000 0x9c6 GENERAL ERRATA G1 Core Operation Is Limited to a 3 0V Minimum The current versions of the MPC823e silicon are only tested and verified at 3 0V 3 6V power Because of this low voltage operation at 2 2V cannot be guaranteed to power the core Workaround None G2 The External Bus Transaction May Hang After a PLPRCR Write Access An endless external bus transaction can occur on the next external bus access after executing a PLPRCR write command that changes the MF field The PLPRCR write command causes the PLL to freeze the clocks until it is locked again according to the new MF value The failure mechanism occurs because the clock unit indicates operation complete before all necessary tasks are actually completed The next external bus request is driven by the system interface unit and suddenly all clocks are stopped MOTOROLA MPC823E DEVICE ERRATA 61J13D 3 Workaround The store instruction to the PLPRCR register should be in a burst aligned address cache line followed by an isync instruction The instruction cache should be enabled while executing this code sequence G3 LC
3. interrupt due to an error in a load store cycle a data storage interrupt or an alignment interrupt occurs set the DAR and DSISR registers to the effective address associated with the interrupting instruction In some 8 MPC823E DEVICE ERRATA 61J13D MOTOROLA MOTOROLA cases when a load store breakpoint occurs when one of the debug counters expires just before one of the above interrupts occur the value of the DAR and DSISR is changed Although the interrupt is after the breakpoint and therefore should be ignored by the processor the DAR and DSISR are updated The value of the DAR and DSISR is normally used by the software inside these interrupt routines and may influence program flow only if these interrupts are nested one inside the other and a load store breakpoint is used inside one of these interrupt routines See Section 6 Core and Section 20 Development Support for details burt_253 DOC3 SDMA Aggressive Mode Bit 25 of the SDCR am LAM LCD Video Aggressive Mode 0 Disable LCD Video aggressive mode Priority depend on the LAID field 1 Enable LCD Video aggressive mode The LAID and RAID fields must be equal to 00 This bit affects all SDMA transfers including LCD and Video Controller transfers D0C4 XFC Capacitor Values Based on the PLPRCR Field Table 5 4 XFC Capacitor Values Based on the MF Field in the MPC823e User s Manual on page 5 23 shows the recommended values for UDR2 MPC823e rev 0 silicon
4. D Off and On Sequence With a Pending SDMA Cycle Causes Wrong Data Fetch If the LCD controller is turned off and there is a pending SDMA cycle for the LCD controller and then the LCD is turned on again before the SDMA cycle completes the LCD controller will start fetching from the start address 16 instead of the start address Workaround Make sure that the pending SDMA cycle is completed before turning on the LCD controller This can be done by performing an access to external memory before turning on the LCD controller G6 LCD Controller Off Sequence When LAM Bit Is Set May Cause the CPU to Lock Up The LCD aggressive mode LAM bit of the SDCR register allows aggressive arbitration for the LCD controller when doing DMAs to system memory If this bit is set and the LCD controller is turned off the LCD controller generates a spurious request to the SDMA that may cause the CPU to lockup Workaround Clear the LAM bit before turning off the LCD controller G7 Possible External Bus Hang Occurs Under Certain Error Conditions The external bus cycle may hang when the following sequence of events occur 1 The transaction on the external bus ends as a result of TEA assertion OR a bus monitor timeout occurs AND 2 The next transaction also ends with a TEA assertion or a bus monitor timeout burt 300 Workaround None G8 Higher Than Normal Current Consumption Without Executing a MULLW Instruction In the integer multip
5. MPC823E61J13ERID REV 1 0412003 ala MOTOROLA digitaldna intelligence evaryunhers MPC823e MASK 61J13D DEVICE ERRATA SILICON MASK SET 61J13D APRIL 2003 CPU ERRATA These errata apply to the MPC823e 61J13D CDR2 silicon The errata that are currently scheduled to be addressed in the future revision of the silicon are so marked Changes to this errata are in italics CPU1 Bus Error Not Fully Supported by the Data Cache on a Burst The data cache does not support a bus error that might occur on the second or third data beat of a burst burt_232 Workaround Avoid using a bus error in this case CPU2 Incorrect Data Breakpoint Detection on Store Instructions When a breakpoint on data occurs and you have programmed the size elements as byte or half word the following may occur A breakpoint might be detected when it should not A breakpoint might not be detected when it should Either of these two cases can occur if the data that is programmed to be detected matches some other portion of the register that is currently stored to memory by the store byte or store half word instruction For example e Assume that you have programmed a byte data breakpoint on a store instruction and you are looking for the byte element 0x55 Assume that register R1 has the value 0x00080000 R10 has the value 0x55443322 and the stb R10 0x3 R1 store instruction is performed What occurs is that byte 0x22 from R10 is s
6. any DIVW instructions dividing by one after the isync see errata G9 If more than 2 DIVWs are required then the additional CACHE lines must be loaded and locked into the ICACHE MPC823E DEVICE ERRATA 61J13D 5 For example If your longest transaction is 16 CPU clocks then you must add 2 DIVW instructions global SetPLPRCR align 16 SetPLPRCR nop nop nop addi 15 0 1 stw r4 PLPRCR r3 This cache line MUST be in the cache isync divw r4 r4 r5 divw r4 r4 r5 nop This cache line MUST be in the cache nop These NOP s are to prevent the CPU from nop trying to fetch from the BLR target by nop filling the instruction prefetch queue nop This cache line MUST be in the cache nop nop blr G17 Address Bus May Consume Excess Current in Low Power Modes When entering Sleep or Deep Sleep Mode normally PLPRCR FIOPD is set to 1 to enable internal pulldowns on the Address and Data Bus In some units the Address Bus pins are not sufficently pulled down This may cause excess current draw The Data Bus is not affected Workaround None Fixed in Rev B G18 Open Drain Pins Do Not Allow 5 Volt Pullups The Open Drain pins on the MPC823 will not allow external pullups to raise the voltage to the normal levels Workaround None MPC823E DEVICE ERRATA 61J13D MOTOROLA GENERAL CUSTOMER INFORMATION MOTOROLA Although not generally considered to be errata the following items are g
7. causes an incorrect value to be present in the VF flush information when the unimplemented exception occurs burt_251 Workaround None CPU4 Case of I Cache Using Address of Old Page When Fetching New Page The Instruction Cache uses the address associated with the old page when fetching the first data from a new page under the following circumstances 1 There is a show cycle on a sequential instruction which crosses the page boundary 2 The internal bus is busy during the IMMU request with the old page number Thus on the next cycle the I Cache uses this incorrect address to access the external memory and internal cache burt_285 Workaround Do not run in show all mode or do not put a sequential instruction in the last address of an MMU page MPC823E DEVICE ERRATA 61J13D MOTOROLA CPM ERRATA CPM14 RCCR and RMDS Should Be Written To As A Single 32 bit Register The ERAMAK bit is cleared in the RISC Microcode Development Support Control Register RMDS if the register s location is accessed as either part of a half word or byte access Workaround If the ERAMAK is to be set the RMDS must be accessed as part of a word starting at IMMR 0x9C4 to IMMR 0x9C7 It is best to write to these two registers as if they were a single 32 bit register See register table below RCCR RMDS BIT lalala lals lly 8 9 10 11 12 13 14 15
8. http motorola com semiconductors Information in this document is provided solely to enable system and software implementers to use Motorola products There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document Motorola reserves the right to make changes without further notice to any products herein Motorola makes no warranty representation or guarantee regarding the suitability of its products for any particular purpose nor does Motorola assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability including without limitation consequential or incidental damages Typical parameters that may be provided in Motorola data sheets and or specifications can and do vary in different applications and actual performance may vary over time All operating parameters including Typicals must be validated for each customer application by customer s technical experts Motorola does not convey any license under its patent rights nor the rights of others Motorola products are not designed intended or authorized for use as components in systems intended for surgical implant into the body or other applications intended to support or sustain life or for any other application in which the failure of the Motorola product could create a situation where personal i
9. ited memory Setting the memory to burst inhibited will not solve the problem Workarounds Do not use data show cycles in a system that performs SDMA bursts These include systems that use ATM Fast Ethernet and memory to memory IDMA G14 CPU Receives A Machine Check After Writing to the PLPRCR The CPU may receive a machine check after writing to the PLPRCR This error is caused by an extra clock generated by the clock block after the SIU releases the bus When the internal bus is released the CPU begins a transaction The CPU s clocks are then stopped mid cycle and it never receives the acknowledge from the bus The failure mechanism occurs due to an internal logic synchronization issue aggravated by memory refreshes performed by the UPM The problem is only evident when entering and exiting doze mode frequently such as when using doze to conserve power The possibility of encountering this problem is small but finite 1 in a million entries Workaround Prevent the CPU from getting the bus during the extra clock To do so you must enable the instruction cache and insert a delay To calculate how long of a delay is necessary take the longest bus transaction including memory refresh and PCMCIA in CPU clocks The resultant number of clocks must be executed using instructions such as NOP 1 clock ISYNC 2 clocks or DIVW 13 clocks If you use the DIVW instruction then divide the resultant number by 13 and round up Then insert this m
10. ly module in the core there are internal latches that do not get initialized properly during reset Due to this improper initialization there is a 1 8 chance of a driver contention which may create higher than normal current consumption in various modes This current consumption is most noticeable in the lower power modes burt_361 Workaround Adding a mullw instruction puts the two control lines into a valid state eliminating the contention MPC823E DEVICE ERRATA 61J13D MOTOROLA MOTOROLA G12 Incorrect Reporting of Loss of Lock Reset Status The RSR LLRS bit is set by both unintentional and software initiated loss of lock The RSR LLRS bit should be set only by an unintentional loss of lock Software initiated loss of lock e g changing the SPLL multiplication factor or entering low power modes should not set this bit Workaround The PLPRCR SPLSS functions as intended Reference this bit instead G13 Conflict Between Data Show Cycles and SDMA Burst Writes IF data show cycles are enabled via SIUMCR DSHW ANDan internal register or dual port RAM access is made immediately following an SDMA burst write THEN the SDMA burst write may be corrupted The observed phenomenon is that a burst write with four operands will hold the second operand into the third and fourth burst beats For example a burst write of A B C D will be observed on the bus as A B B B This behavior can also occur when the SDMA burst is to burst inhib
11. njury or death may occur Should Buyer purchase or use Motorola products for any such unintended or unauthorized application Buyer shall indemnify and hold Motorola and its officers employees subsidiaries affiliates and distributors harmless against all claims costs damages and expenses and reasonable attorney fees arising out of directly or indirectly any claim of personal injury or death associated with such unintended or unauthorized use even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part MOTOROLA MOTOROLA and the Stylized M Logo are registered in the US Patent and Trademark Office All other product or service names are the property of their respective owners Motorola Inc is an Equal Opportunity Affirmative Action Employer Motorola Inc 2003 MPC823E61J13ER D Rev 1 04 2003
12. set an instruction breakpoint on this instruction the chip will behave unpredictably Workaround Disable instruction breakpoints when setting the IFM bit CI 102 Concurrent Operation Of Ethernet amp i2c or SPI has Overlapping Parameter RAM Tables When concurrent operation for the Ethernet protocol and either I2C or SPI is set up and used at the same timer there is an overlap in the parameter RAM Workaround There is microcode available that moves the I C SPI parameter RAM entries to another location in the dual port RAM To use this download the description of the change and the object code file from the website at http www mot com SPS ADC pps _subpgs _etoolbox 8XX i2c_spi html This package is called the MPC8XX 12C SPI Microcode Package MPC823E DEVICE ERRATA 61J13D 7 CI 103 Port A Pins PA9 and PA11 May Consume Excess Current in Low Power Modes When the Port A pins PA9 and PA11 are configured as General Purpose Outputs then the MPC823 may consume excess current in Sleep or Deep Sleep mode due to internal floating nodes Other than the 1mA of typical excess current there are no operational issues Workaround Before entering Deep Sleep Mode set PAPAR DD9 DD11 and PADIR DR9 DR11 to 1 to configure them as TDM pins See Section 16 14 3 on page 16 470 of the MPC823 User s Manual Be sure to read CIO4 below CI 104 Port A Pins PA9 and PA11 May Consume Excess Current in Low Power Modes While in TDM Mode When
13. the Port A pins PA9 and PA11 are configured as TDM pins the MPC823 may consume excess current in Sleep or Deep Sleep modes If the TDM is not active these pins are tristated causing excess current consumption Other than the 100 uA of typical excess current there are no operational issues Workaround Set SIGMR ENA and SIMODE STZA to 1 before entering Sleep or Deep Sleep modes See Section 16 7 5 on page 16 126 of the MPC823 User s Manual GENERAL DOCUMENTATION ERRATA ASSOCIATED WITH SILICON OPERATION The following items reflect additional information about the operation of the MPC823e and references made in the MPC823e User s Manual Please refer to the manual for clarification DOC1 Cache Inhibit Operation In some cases the last instruction executed from a certain page gets the caching inhibited attribute of the next page when the page change occurs between the time a fetch request was issued to the instruction cache and the time the instruction cache delivers the instruction to the sequencer Since the instruction cache inhibit is only used for performance reasons mostly for not caching very fast memories or pages that include non real time programs the performance effect of this feature is negligible See Section 9 Instruction Cache for more information burt_237 DOC2 Updating the DAR and DSISR with Debug Counter Operation If a load store breakpoint occurs as a result of debug counter expiration when oa machine check
14. tored to address 0x00080003 and this should not generate a breakpoint since 0x22 does not equal 0x55 but in some cases it can and does in this scenario R10 does include the data 0x55 The result is a breakpoint is executed when it should not be e Assume that in the above case you are programming for byte element 0x22 maybe a breakpoint condition will not be detected even though it should burt_246 Note These fault cases depend on the previous Load Store instruction address If the previous Load Store instruction address LSB is different from the current instruction address LSB then an incorrect breakpoint detection might occur Workaround None CPU3 Program Trace Mechanism Error In the following cases there is an error in the program trace mechanism e Ox00004ff0 divw r25 r27 r26 e 0x00004ff4 divw r28 r27 r26 e 0x00004ff8 unimplemented e 0x00004ffc b 0x00005010 and where 0x00005010 belongs to a page where a page fault occurs The divide takes a relatively long time so the instruction queue gets filled with the unimplemented instruction which is the branch and the branch target page fault When the sequencer takes the unimplemented instruction it releases the fetch that was blocked by the mmu error which causes the queue to get another instruction in addition to the first page fault Because the second fault is sequential to the branch target it is not reported by the queue flush VF and this
15. uidelines for using the device appropriately Cl 100 External Interrupt Handling For external interrupt pins if a request signal is a pulse the interrupt request pin should be configured to edge detect mode This ensures that the interrupt will be recognized even if interrupts are temporarily blocked or disabled by the software The interrupt service routine ISR should clear the edge status flag after the ISR is entered and prior to setting the MSR s EE bit if it waits until after the EE bit is set a second interrupt may be taken If a request signal is a standard handshake the assertion is asynchronous but the negation occurs upon request from the ISR This ensures that the interrupt is taken and the source of the interrupt is known The timing with respect to the EE bit is the same To avoid spurious interrupts interrupt masks should not be set while interrupts might be sent to the core Likewise no interrupts should be disabled while the interrupt might be pending at the core That way when the core responds to the interrupt request the request will still be pending and the core can determine the source of the interrupt To accomplish all of the above the EE bit should be disabled when masks are set or when interrupt enables are cleared Cl 101 Move to Special Register mtspr Access to ICTRL Register If you use mtspr to set the Ignore First Match IFM bit of the ICTRL register to 1 at the same time that you
Download Pdf Manuals
Related Search