T715 User Manual
Contents
1. Introduction Thank you for purchasing this Timex Dual Alarm Clock Radio with Redi Set Automatic Time Setting System The clock in this model will set itself to the correct year month date day and time the first time you plug it in and after every power interruption The default setting is the Eastern Time zone All you need do is set it to your own time zone once and you may never have to adjust it again Daylight Saving Time and Standard Time adjustments are made automatically through the year 2099 This model is truly the cure for the annoying flashing 12 00 display This model includes a programmable dual alarm system that allows you to set one or both alarms for weekdays only weekends only or everyday operation And you can have one alarm wake you to the buzzer while the second alarm wakes you to your favorite radio station And the Sure Alarm battery back up system will operate the buzzer alarm to wake you up even if the power is off at the wake up time Best of all with Xtreme Battery Back Up XBBU system the long life 3 volt lithium battery that is pre installed in your unit will last for 5 to 8 years before it needs to be replaced a major money saver compared to buying new 9 volt batteries every 6 months And when the 3 volt lithium battery finally does need to be replaced a low battery indicator begins flashing in the display Please read this manual completely to understand all of the great features included in your m2. Off Antenna Information AM The AM bar antenna is inside the cabinet If AM reception is weak change the position of the cabinet until the internal antenna picks up the strongest signal FM Make sure the external FM antenna wire on the back cabinet is fully unwound and extended to its full length Wake To Radio 1 Turn the radio On and select the band station and volume level that you wish to hear when the alarm comes On then turn the radio Off again 2 Reconfirm the wake up time and alarm mode settings for the alarm you are using Alarm 1 or Alarm 2 or both alarms 3 Rotate the ALARM SELECTOR control on the front panel for one or both alarms to the Radio position The appropriate AL 1 and or AL 2 indicators will light up to confirm that the alarms are set 4 At the selected wake up time the radio will turn On It will play for one hour and then shut off automatically 5 To stop the radio sooner press either the appropriate ALARM 1 or ALARM 2 button or press the RADIO ON OFF button The radio will stop but the alarm remains set and will turn on again at the same time on the following day depending on the Alarm Mode setting 6 If you do not want the alarm to repeat on the following day rotate the appropriate ALARM SELECTOR switch to the Off position The AL 1 and or AL 2 indicators turn off Wake To Buzzer Crescendo Alarm Note Alarm 1 and Alarm 2 have different buzzer sounds
3. Digital Radio Frequency Display This clock radio features a digital radio frequency display instead of a dial scale to make tuning easier especially in a dark room The jumbo LED time display automatically changes to a radio frequency display as soon as you begin turning the TUNING control And the display automatically changes back to the correct time within 5 seconds after you release the TUNING control 1 Set the BAND AM FM selector switch to the desired band AM or FM 2 Set the VOLUME control to a low setting 3 Press the RADIO ON OFF button to turn the radio On The display changes from time to an AM or FM Frequency 4 Rotate the TUNING control to select the desired radio frequency Important It is not necessary to set the display to the exact frequency of your desired station Just use the display as a guide and rotate the TUNING control until you find the strongest and the best reception even if the frequency number shown on the display is slightly higher or lower than the actual station frequency Within 5 seconds after you release the TUNING control the display automatically returns to the correct time If you wish to check the station frequency again press the ALARM MODE Display button The display will change from time to radio frequency for 5 seconds and then return to time display 5 Adjust the VOLUME control to the desired setting 6 When you are finished listening press the RADIO ON OFF button to turn the radio
4. clock after a total memory loss proceed as follows 1 Follow the instructions on page 9 and install a fresh CR2450 lithium back up battery 2 Connect the radio to the AC outlet and wait until the time is displayed 3 Press the MONTH DATE and TIME buttons together to display the Year While holding the MONTH DATE and TIME buttons press the SET or buttons to adjust the Year display 4 Press the MONTH DATE button to display the Month and Date While holding the MONTH DATE button press the SET lt or gt buttons to adjust the Month Date display The Day indicator will change according to the Month Date selected 5 Depress the TIME button and the SET or buttons to adjust the time display Be sure to observe the AM indicator to confirm that you have set the time correctly If the AM indicator does not appear the time displayed is PM 6 After you have reset the Year Month Date and Time displays check your alarm time and alarm mode settings and adjust as required Lithium Battery Precautions e Dispose of exhausted battery properly in accordance with your local regulations e Do not leave the exhausted battery lying around where a young child or pet could play with or swallow it If the battery is swallowed contact a physician immediately e Battery may explode if mistreated Do not attempt to recharge it or disassemble it Do not dispose of the old battery in a fire Care and Maintenance There are no user serviceabl
5. do not allow limitations on implied warranties or exclusion of consequential damages so these restrictions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state 2009 SDI Technologies Inc All rights reserved TIMEX is a registered trademark of Timex Corporation the United States and other countries T715 120409 Printed in China 11
6. the original setting when the power is restored Adjusting The Wake Up Times Your Redi Set clock radio has two separate alarms that can be set and used independently You may use the alarms to wake two people at different times or you may use one alarm for weekdays and the other for weekend wake up times The initial default setting for Alarm 1 is 6 00 AM The initial default setting for Alarm 2 is 7 00 AM The procedure for adjusting the wake up times is the same for both Alarm 1 and Alarm 2 1 Depress and hold either the ALARM 1 or ALARM 2 Setting Button The display will change from the correct time to the Alarm 1 or Alarm 2 default wake up time 2 While holding the ALARM 1 or ALARM 2 Setting Button depress either the SET 4 or gt buttons to move the display back or forward to your desired wake up time 3 When the desired wake up time appears on the display release the SET or buttons Note Be sure that you have set the wake up time correctly by observing the AM indicator If the AM indicator appears the wake up time is AM If the AM indicator does not appear the wake up time is PM 4 When the desired wake up time AM or PM appears on the display release the ALARM 1 or ALARM 2 setting buttons Selecting The Alarm Mode Your Redi Set clock radio allows you to select from among three different alarm operation modes for either alarm The alarm modes are e Everyday the alarm will turn on all 7 days e We
7. IME ZONE button and press either the SET 4 or buttons until your own zone number appears in the display then release the buttons The clock display will change to the correct time in the time zone you selected The clock will always return to the correct time in the zone you selected after every power interruption If you move to a different time zone simply change the default zone display to the new zone and the Redi Set internal computer will remember that setting for you Date Display To see the correct date at any time depress the MONTH DATE button The display changes from Time to Month and Date MM DD For example October 9th will be displayed as 10 9 Year Display To see the correct year depress the MONTH DATE and TIME buttons together The display changes from Time to Year Daylight Saving Time DST and Leap Year Adjustments All Daylight Saving Time and Leap Year adjustments are made automatically by the Redi Set internal computer as follows e Start of Daylight Saving Time At 2 00 AM on the 2nd Sunday in March the clock will automatically advance to 3 00 AM e End of Daylight Saving Time At 3 00 AM on the 1st Sunday in November the clock will automatically reset to 2 00 AM e Leap Year At 12 00 midnight on February 28th in a Leap Year the calendar display will automatically change to 2 29 Note If you live in an area that does not observe Daylight Saving Time DST you may disable the automatic Daylight
8. Model T715 TI M 5 X AM FM Dual Alarm Clock Radio With Redi Set Automatic Time Setting System gt ALARM MODE SSON Se SE Se ED TE SE SN 2 ES OOZE i SLEEP OFF ALARM Q REDI SET TIMEX AM ALARM RADIO e XBBU EXTREME BATTERY BACKUP For additional information online registration and exclusive special offers visit our website www timexaudio com For questions or comments regarding this or other products please call our toll free number 1 800 888 4491 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE AVERTISSEMENT POUR R DUIRE LE RISQUE D INCENDIE OU DE CHOC LECTRIQUE NE PAS EXPOSER CET APPAREIL SOUS LA PLUIE ET L HUMIDIT of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence a risk electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance servicing instr
9. Saving Time DST feature Depress and hold the TIME ZONE button for 10 seconds The display will briefly show OFF and then return to the correct time The automatic DST feature is now disabled and the time will not change automatically from Standard Time to Daylight Saving Time Repeat this procedure again to re enable the automatic DST feature After holding the TIME ZONE button for 10 seconds the display will briefly show ON and then return to the correct time The automatic DST feature is now re enabled Manual Time Adjustments Some people like to set their clocks 5 to 10 minutes fast to make sure that they will always be on time Even though the Redi Set internal computer sets the time automatically you still have the option of adjusting the time manually if you wish To manually adjust the time display depress and hold the TIME button and press either the SET or buttons to adjust the time display back or forward as desired Each press of the SET 4 or gt buttons will change the display by one minute If you hold SET 4 or gt buttons the display will continue to change The display will change slowly at first two minutes at a time But if you continue holding the SET or gt buttons the display will change rapidly Note If you manually adjust the time your new setting is entered into the Redi Set internal computer as the new default time setting If the power is interrupted the display will return to your new setting not
10. Ta ow AL2 Alarm 2 Indicator Alarm 1 Indicator Time Year Month Date and Nia Battery Indicator Radio Frequency Display Operating Instructions Setting The Time The First Time IMPORTANT The first time you connect your Redi Set clock radio to the AC outlet the internal computer will automatically set the time correctly for the Eastern Time Zone which is the initial default setting The display will begin a countdown sequence 5 4 3 2 1 then the correct year will flash twice the correct Month Date will flash twice and then the correct Eastern Time will be displayed If you live in the Eastern Time Zone there is nothing else to do Your Redi Set clock is set correctly and running If you do not live in the Eastern Time zone you must change the default zone display to your own zone You only do this one time and the Redi Set internal computer will remember the new default zone setting and will always return to that setting after a power interruption There are 7 time zones programmed into your Redi Set clock radio ZONE 01 Atlantic Time ZONE 02 Eastern Time Default Setting ZONE 03 Central Time ZONE 04 Mountain Time ZONE 05 Pacific Time ZONE 06 Alaskan Time ZONE 07 Hawaiian Time To change the default time zone depress the TIME ZONE button The number 02 will appear in the display indicating that the default zone is ZONE 02 Eastern Time 4 Operating Instructions Hold the T
11. and the radio will not operate but a separate mini buzzer will turn on automatically to wake you up even if you selected the Wake To Radio option The Sure Alarm buzzer will sound for 3 minutes and then shut off automatically To stop the Sure Alarm buzzer immediately press the RADIO ON OFF button The SNOOZE button has no effect during Sure Alarm operation Note In order to maximize the life of the built in lithium battery please be sure to set the Alarm 1 and Alarm 2 switches to the OFF position if the radio will be disconnected from the AC outlet for more than a few hours This will prevent the Sure Alarm buzzer from turning On unnecessarily 2 Controls and Indicators Snooze Sleep Off Button Time Button Sleep Button Month Date Button ra 5 Alarm Mode Display Button Time Zone Button Alarm 1 Setting Button Alarm 2 Setting Button Radio ON OFF Button Set Forward Button Set 4 Back Button Alarm 1 Selector Off Radio Buzzer Alarm 2 Selector Off Radio Buzzer XBBU EXTREME BATTERY BACKUP Back View Line Input Jack Tuning Control Volume Control AM FM Band Selector Display Dimmer Control PS Power Cord FM Antenna Wire Display with Indicators m Day Indicators AM Indicator am f D aux Aux Line In Indicator KHz KHz AM Frequency Indicator Mkz MHz FM Frequency Indicator a es AL
12. commend that you place a small cloth between the radio and your furniture or that you apply small felt pads on the bottom of the rubber feet Power Source This radio is designed to operate on normal 120V 60Hz AC power only Do not attempt to operate this radio on any other power source You could cause damage to the radio and such damage is not covered by your warranty This radio should be connected to an AC outlet that is always live Do not connect it to an outlet that is controlled by a wall switch When the power to the radio is interrupted the installed lithium battery takes over to maintain the time and alarm settings and to operate the buzzer alarm if the power is Off at the wake up time To maximize the life of the lithium battery keep the radio connected to a live AC outlet at all times This radio is equipped with a polarized AC plug with one wide blade and one narrow blade This is a safety feature designed to minimize the chance of electric shock If this plug will not fit into your existing AC outlet do not try to force it and do not try to file the wider blade to make it fit Contact a qualified licensed electrician to replace your outdated outlet Sure Alarm Battery Back Up System This Timex Redi Set Clock Radio includes a Sure Alarm battery back up circuit that will wake you up even if the power is off at the selected wake up time If your power is off at the wake up time the clock display will be off
13. e Alarm 1 is a Single Beep sound e Alarm 2 is a Double Beep sound You will be able to tell which alarm is going off by the sound that it makes 1 Reconfirm the wake up time and alarm mode settings for the alarm you are using Alarm 1 or Alarm 2 or both alarms 2 Rotate the ALARM SELECTOR control on the front panel for one or both alarms to the Buzz position The appropriate AL 1 and or AL 2 indicators will light up to confirm that the alarms are set 3 At the selected wake up time the buzzer will turn On It will continue for one hour and then shut off automatically 4 To stop the buzzer sooner press the appropriate ALARM 1 or ALARM 2 button The buzzer will stop but the alarm remains set and will turn on again at the same time on the following day depending on the Alarm Mode setting 5 To stop the buzzer and turn the radio On immediately press the RADIO ON OFF button instead of the ALARM 1 and ALARM 2 button 6 If you do not want the alarm to turn the buzzer on the following day set the appropriate ALARM selector to the Off position Radio And Buzzer Operation You may set one alarm for wake to RADIO and the other for wake to BUZZER Just set the ALARM 1 and ALARM 2 Selector Controls to the desired positions Snooze Control After the alarm turns on in the morning you may press the Snooze button to stop the alarm for 9 minutes After 9 minutes the alarm turns on again The Snooze operation may b
14. e parts inside this radio Please refer all service problems to a qualified service facility If the cabinet becomes dusty wipe the exterior with a soft dust cloth only Never use dusting sprays or polishes on the cabinet If the cabinet becomes dirty or smudged with fingerprints it may be wiped with a soft cloth that has been slightly dampened with a mild soap and water solution Always disconnect the power cord from the AC outlet before cleaning and never allow any liquid to get inside the cabinet 10 Limited 90 Day Warranty Information Timex Audio Products a division of SDI Technologies Inc hereafter referred to as SDI Technologies warrants this product to be free from defects in workmanship and materials under normal use and conditions for a period of 90 days from the date of original purchase Should service be required by reason of any defect or malfunction during the warranty period SDI Technologies will repair or at its discretion replace this product without charge except for a 5 00 charge for handling packing return UPS postage and insurance This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center listed below The product must include proof of purchase including date of purchase The fee for service after the warranty period or without proof of purchase is 10 00 Before returning this product for service please first replace the batteries
15. e repeated several times within one hour of the original alarm time But after one hour the alarm will not turn on again During Snooze operation the appropriate Alarm indicator flashes in the display Sleep To Music Timer You can program the Sleep Timer to play the radio from 1 minute up to 99 minutes and then shut off automatically 1 Press the SLEEP button The display will briefly show 60 and the radio will begin to play After 60 minutes the radio will shut off automatically Each time you press the SLEEP button the sleep timer will start at 60 minutes This is the initial sleep timer default setting 2 To increase or decrease the amout of time that the radio will play before shutting off hold the sleep button and press either the SET or buttons to change the display to the desired sleep time up to a maximum of 99 minutes or a minimum of 1 minute Note When you change the sleep timer from the 60 minute default setting to a different setting the new setting becomes the new default setting Whenever you activate the sleep timer it will begin with your new default setting and count down to zero from that point 3 To cancel the sleep timer before it counts down to 0 and shut the radio Off immediately press the SNOOZE bar IMPORTANT Remember that the station and volume settings that you choose for the Sleep To Music operation are the same settings that you will hear if you set the alarm for wa
16. ekdays only the alarm will only turn on Monday through Friday e Weekends only the alarm will only turn on Saturday and Sunday To check the Alarm Mode setting for Alarm 1 depress the ALARM 1 setting button The display will show the Alarm 1 wake up time and the Day indicators will show you the alarm mode that is selected e If all 7 Day indicators are On the Everyday alarm mode is selected e If only the MON Monday through FRI Friday indicators are On the Weekdays only mode is selected e If only the SAT Saturday and SUN Sunday indicators are On the Weekends only mode is selected To change the Alarm Mode setting for Alarm 1 hold the ALARM 1 setting button and press the ALARM MODE Display button until the Day indicators show the desired mode setting Weekdays only Weekends only or Everyday operation Release the ALARM MODE and ALARM 1 Setting buttons and the display will return to the correct time Follow the same procedure to select the desired Alarm Mode for Alarm 2 if necessary Checking The Wake Up Times And Alarm Mode Whenever you want to check the wake up time or alarm mode settings simply press either the ALARM 1 or ALARM 2 Setting Buttons The display will change from correct time to wake up time and the DAY indicators will show you the alarm mode that is currently selected Release the ALARM 1 or ALARM 2 setting buttons to return to the correct time Listening to The Radio
17. if applicable with fresh ones as exhausted or defective batteries are the most common cause of problems encountered f service is still required 1 Remove batteries if applicable and pack the unit in a well padded heavy corrugated box 2 Enclose a photocopy of your sales receipt credit card statement or other proof of the date of purchase 3 Enclose a check or money order payable to the order of SDI Technologies Inc for the sum of 5 00 or 10 00 if after the warranty period or without proof of purchase 4 Send the unit prepaid to the Factory Service Center listed below Consumer Repair Department SDI Technologies Inc Timex Audio Products Division 1330 Goodyear Drive El Paso TX 79936 6420 NOTE This warranty is valid only if the product is used for the purpose for which it was designed It does not cover i products which have been damaged by negligence misuse or accident or which have been modified or repaired by unauthorized persons ii cracked or broken cabinets or units damaged by excessive heat iii damage to tape cassettes if applicable iv the cost of shipping this product to the Factory Service Center and its return to the owner This warranty is valid only in the United States of America and does not extend to owners of the product subsequent to the original purchaser Any applicable implied warranties are also limited to 90 days and SDI Technologies will not be liable for consequential damages Some states
18. ke to radio the following morning Display Dimmer Control You can reduce the display brightness by sliding the DIMMER control to the Low position Line Input Jack You may listen to the sound from an iPod MP3 player CD player or other external music source by connecting the external device to the Line In jack on the back of this clock radio Use an audio cable not included with 3 5mm mini plugs to connect the headphone jack of the external device to the Line In jack of this unit An AUX indicator will appear on the display when a Pant is nn to the Line In jack of this radio Begin playback on the external device and adjust the VOLUME control of this clock radio Note You must remove the audio cable from the Line In jack of this clock radio in order to listen to AM or FM When the audio cable is disconnected the AUX indicator turns Off in the display Changing The Lithium Back Up Battery When the back up battery voltage drops below a certain level the Low Battery indicator lt a Low begins flashing in the display When you see this indicator you should replace the battery as soon as it is convenient for you to do so To replace the battery proceed as follows IMPORTANT Leave the radio connected to the AC outlet when replacing the battery to avoid losing all of your time and alarm settings 1 Purchase a replacement 3V lithium battery The battery type is CR2450 This type battery is available almost everywhere that batteries a
19. ne doivent pas tre expos es de forte chaleur tel qu la lumi re du soleil au feu o autres choses de semblable Caution marking is located at the bottom of apparatus Les pr cautions d emploi sont inscrites en bas de l appareil The marking information is located at the bottom of apparatus Les marquages sont inscrits en bas de l appareil A Consumer Guide to Product Safety IMPORTANT SAFETY INSTRUCTIONS This unit has been designed and manufactured to assure your personal safety Improper use can result in potential electrical shock or fire hazards APoON gt D Read these Instructions Keep these Instructions Heed all Warnings Follow all instructions Water and Moisture Do not use this apparatus near water For example near a bathtub washbowl kitchen sink laundry tub swimming pool or in a wet basement Ventilation Do not block any of the ventilation openings Install in accordance with the manufacturers instructions For example it should not be situated on a bed sofa rug or similar surface that may block ventilation openings Also it should not be placed in a built in installation such as a bookcase or cabinet that may impede the flow of air through the ventilation openings Heat Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Power Sources The unit should be connected to a power supply only of the
20. ntegral convenience receptacles as this can result in a risk of fire or electric shock Damage Require Service Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Servicing The user should not attempt to service the unit beyond that described in the user s operating instructions All other servicing should be referred to qualified service personnel Safety Check Upon completion of any service or repairs to this product ask the service telchnician to perform safety checks to determine that the product is in proper operating condition Antenna Do not connect to an external antenna Questions Service Warranty Visit www timexaudio com Table of Contents GG IMPORT OM occ ces vaca tccccce ceuceccacstuncceccncctassctcesccssseurccste tsaevssassecs vase wacasscuataecise I 1 Introductions int cet cs eden eySvaceevnaee E cata vedeu E in nn nn den les cela et rennes teste trans 2 Preparation for Use died nent ee a aa Oaa da taie aes de name a elec nadie 2 Controls and Indicat iSannn ceases nn eas Sessa a EN sh ives cw en nr ei Nr Anne 3 Display witht IndiCatorS scsi cscs co sates ceca lens rene mone cie oben wo mass mn a tient a ete vee ne entie
21. odel Please retain this manual for future reference and because the warranty and product service info are printed at the end of this manual Preparation For Use Unpacking And Set Up Remove the radio from the carton and remove all packing materials from the radio We recommend that if possible you save the carton and packing materials in case your radio ever needs to be returned for service Using the original carton and packing material is the best way to protect your radio from damage in transit If you do dispose of the carton and packing material please do so properly Timex cares about our environment e Place the radio on a stable level surface convenient to an AC outlet and away from direct sunlight or sources of excess heat dust moisture or humidity e Unwind the external FM antenna on the back cabinet and extend it to its full length for best FM reception IMPORTANT Protect Your Furniture This radio is equipped with non skid rubber feet to prevent the radio from moving when you operate the controls These feet are made from special non migrating rubber material formulated to avoid leaving any marks or stains on your furniture However certain types of oil based furniture polishes wood preservatives or cleaning sprays may react with the rubber feet causing the rubber material to soften and leave marks or a rubber residue on wooden furniture If you will be placing this radio on fine wooden furniture we strongly re
22. re 4 Operating Instructions Listening to The Radio Changing The Lithium Back Up Battery Care and Maintenance Warranty Information FCC Information This device complies with Part 15 of the FCC Rules operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment complies with the limits for a Class B digital device as specified in Part 15 of FCC Rules These limits provide reasonable protection against radio and TV interference in a residential area However your equipment might cause TV or radio interference even when it is operating properly To eliminate interference you can try one or more of the following corrective measures e Reorient or relocate the receiving antenna e Increase the distance between the equipment and the radio or TV e Use outlets on different electrical circuits for the equipment and the radio or TV e Consult your dealer or an experienced radio television technician if the problem still exists Modifying or tampering with your system s internal components can cause a malfunction and might invalidate the system s warranty and void your FCC authorization to operate it This Class B digital apparatus complies with Canadian ICES 008 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada
23. re sold 2 Remove the battery from the packaging so it is ready to install 8 Place that radio face down on a towel or similar soft surface to avoid scratching the front lens 4 Use a small Phillips screwdriver to remove the screw that secures the battery holder and slide the battery holder out of the cabinet Battery Compartment 9 5 Remove the original battery from the battery holder and insert the new battery into the holder in the same way with the side facing up Slide the battery holder with the new battery back into the cabinet and secure the holder with the small sen 6 Turn the radio right side up and confirm that the Low Battery indicator ta ow is Off CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type PRECAUTION Danger d explosion si les piles sont remplac es de fa on incorrect Remplacer les piles seulemnet par le m me type de pile ou l quivalent Resetting The Clock After a Total Memory Loss If you experience a power failure with an exhausted back up battery in the radio all of the time and alarm settings may be lost In this case the clock will reset itself to its initial default settings when power is restored If you notice that the time on the display is incorrect press the MONTH DATE button to check the calendar setting If the Month and Date are also incorrect you probably experienced a total memory loss To reset the
24. type described in the operating instructions or as marked on the appliance Grounding or Polarization Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety When the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Power Cord Protection Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Itis always best to have a clear area from where the cord exits the unit to where it is plugged into an AC outlet Cleaning Unplug this product from the well outlet before cleaning Do not use liquid cleaners or aerosol cleaners Clean only with a dry cloth Non Use Periods The power cord of the unit should be unplugged from the outlet when it is to be left unused for a long period of time Objects and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings Attachments Only use attachments accessories specified by the manufacturer Lightning Unplug this apparatus during lightning storms or when unused for long periods of time Overloading Do not overload wall outlets extension cords or i
25. uctions in the literature accompanying the appliance The symbols above are located at the bottom of the cabinet CAUTION To prevent electric shock do not use this Polarized plug with an extension cord receptacle or other outlets unless the blades can be fully inserted to prevent blade exposure ATTENTION Pour pr venir les chocs lectriques ne pas utiliser cette fiche polaris e avec un prolongateur Une prise de courant ou une autre sortie de courant sauf si les lames peuvent tre ins r es a fond sans en laisser aucune partie a decouvert A Consumer Guide to Product Safety The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on apparatus L appareil ne doit pas tre expos aux coulements ou aux claboussures et aucun objet ne contenant de liquide tel qu un vase ne doit tre plac sur l objet ain plug is used as disconnect device and it should remain readily operable during intended use In order to disconnect the apparatus from the mains completely the mains plug should be disconnected from the mains socket outlet completely La prise du secteur ne doit pas tre obstru e ou doit tre facilement accessible pendant son utilisation Pour tre compl tement d connect de l alimentation d entr e la prise doit tre d branch e du secteur Battery shall not be exposed to excessive heat such as sunshine fire or the like Les piles
Download Pdf Manuals
Related Search