MANUBAL V60 instructions
Contents
1. 5 2 UNHITCHING THE MANUBAL BALE GRAB 5 2 1 Remove the MANUBAL unit with the grab open ram rod retracted 5 2 2 Release the hydraulic pressure and unhitch MX Y 19 rue de Rennes BP 83221 F 35690 ACIGNE 7 Modification reserved 6 GRAB OPENING CLOSING ADJUSTMENT The extent of opening and closing of the grab can be adjusted to match the type of bale being handled 6 1 ROUND BALES This setting enables 0 90m to 1 80m diameter bales to be picked up 6 1 1 Position the MANUBAL bale grab upright 6 1 2 Open the grab halfway Lower the MANUBAL bale grab to the ground Stop the engine 6 1 3 Remove the clip from the rod end ram pin and remove the pin Note the screw on the pin flat acts to prevent rotation and need not be removed 6 1 4 Position the ram opposite the hole for the round bale setting See table below 6 1 5 Insert the pin as well as the synchronising link in the appropriate hole Note check the spacers for correct positioning 6 1 6 Refit the clip 6 1 7 Repeat operations 6 1 3 to 6 1 6 for the cylinder end ram pin 364187_10 MX 7 19 rue de Rennes BP 83221 F 35690 ACIGNE 8 Synchronising links Viewed from below Modification reserved 6 2 RECTANGULAR BALE With the grab open the tines do not extend beyond the vertical mast Rectangular bale pick up is more effective2. Only control the MANUBAL bale grab from the drivers seat Keep operating the controls until movements stop Do not leave the drivers seat without stopping all control movements All personnel must be kept away from the area in which the loader MANUBAL bale grab combination is moving while it is in operation Never pass under a raised bale Never use the MANUBAL bale grab to push a bale Carrying or lifting personnel using the MANUBAL bale grab is forbidden Never stand or pass under the load Before any operation the user must ensure that the MANUBAL bale grab is in proper working order and can be used in complete safety He must also check and ensure thatthe tractor loader MANUBAL bale grab combination is stable by fitting acounterweight to the back of the tractor This should ensure that 20 of gross weight remains on the rear axle of the tractor for optimum safety while travelling and working When travelling on the road it is imperative that the regulations governing use on the public highway be observed size implement markings etc Protruding items such as tine ends must be protected or stowed grab closed lower tine kit retracted Take great care when operating at height in order to avoid catching any items electric power or telephone lines guttering roof trusses etc Whenever the tractor is stopped momentarily or for an extended period the engine must be shut down and the MANUBAL bale g
3. MANUBAL V60 User Manual Read carefully before operating the Manubal UK 365509 AA 0511 Original instructions Dear user We thank you for placing your trust in our product and hope you will find your MX MANUBAL satisfactory in every way Taking a few minutes to read this manual will enable you to use the capabilities of your MX MANUBAL to the full prolong its service life and ensure safe operation The MANUBAL user manual before you is an important document please retain it in order to be able to refer to it if required Make it available to any other users and hand it over it to any new owner in the event of your MX MANUBAL being sold on The illustrations and technical data shown in this document might not match your MX MANUBAL bale grab exactly operating conditions will nevertheless remain the same TABLE OF CONTENTS 1 SAFETY RULES 2 SAFETY STICKERS 3 IDENTIFICATION PLATE 4 DESCRIPTION 5 HITCHING UNHITCHING THE MANUBAL BALE GRAB 6 GRAB OPENING CLOSING ADJUSTMENT 7 WRAPPED BALE GRAB KIT 8 PRINCIPLE OF USE 9 MAINTENANCE STORAGE 10 TECHNICAL SPECIFICATIONS EC DECLARATION OF CONFORMITY Page 1 SAFETY RULES The tractor loader MANUBAL bale grab combination must only be operated by trained and experienced personnel For your complete safety and that of others strict compliance with the hitching and unhitching procedure for the MANUBAL bale grab is required chapter 5 of this manual
4. 6 2 1 Position the MANUBAL bale grab upright 6 2 2 Open the grab halfway Lower the MANUBAL bale grab to the ground Stop the engine 6 2 3 Remove the clip from the rod end ram pin and remove the pin Note the screw on the pin flat acts to prevent rotation and need not be removed 6 2 4 Position the ram opposite the hole for the rectangular bale setting See table below 6 2 5 Insert the pin as well as the synchronising link in the appropriate hole Note check the spacers for correct positioning 6 2 6 Refit the clip 6 2 7 Repeat operations 6 2 3 to 6 2 6 for the cylinder end ram pin Synchronising links Viewed from below MX 7 19 rue de Rennes BP 83221 F 35690 ACIGNE 9 Modification reserved 7 WRAPPEDBALE GRAB KIT This kit converts your MANUBAL unit into a round wrapped bale grab The conversion is very simple and is accomplished in just a few seconds Wrapped bale grab opening closing adjustment The adjustment is carried out using the holes provided for round wrapped bales 7 1 Position the MANUBAL bale grab upright 7 2 Openthe grab halfway Lower the MANUBAL bale grab to the ground Stop the engine 7 3 Remove the clip from the rod end ram pin and remove the pin Note the screw on the pin flat acts to prevent rotation and need not be removed 7 4 Position the ram opposite the hole for the wrapped bale setting See drawing 7 5 Insert the pin as well as the synchronis
5. X E fig MXA o Serial number Seriennummer Ann e Year Poids vide k Unloaded weight Leergewicht g 328462 X 19 rue de Rennes BP 83221 F 35690 ACIGNE N a Modification reserved 4 DESCRIPTION 1 Bracket 6 Synchronising link 2 Grab 7 Rod end ram pin 3 Tine 8 Cylinder end ram pin 4 Ram 9 Telescopic connecting bar 5 Synchronising crank 10 Upper connecting bar MX 7 19 rue de Rennes BP 83221 F 35690 ACIGN 6 Modification reserve 5 HITCHING UNHITCHING THE MANUBAL BALE GRAB 5 1 HITCHINGTHE MANUBAL BALE GRAB 5 1 1 Hook the self centring V notches into the MANUBAL hitch bar for telescopic handlers refer to the manufacturers user manual 5 1 2 Position yourself on the right hand side and lock manually 5 1 3 Crowd back to check that the MANUBAL is being held correctly 5 1 4 Operate each moving component to its fullest extent in each direction to check the hydraulic system is free from leaks and the hoses are routed correctly Position for locking the MANUBAL bale grab
6. Y CE The manufacturer MX 19 Rue de Rennes F 35690 Acigne Hereby declares that the following equipment V60 Manubal Comply with EC directive 2006 42 of the Council of European Parliament and of the council of 17th of May 2009 relating to machines Acign 5th of May 2011 ZZ Loic Mailleux Technical Director MX Z 19 rue de Rennes BP 83221 F 35690 ACIGNE T l 33 0 2 99 62 52 60 Fax 33 0 2 99 62 50 22 e mail contact m x eu
7. e they are connected See to it that straw or hay residues do not jam up the pivot points Check the MANUBAL bale grab to ensure that it is in proper working order throughout and that screws clips and pins are in place before any use Check the condition of the wear bushes and replace them before they are fully worn Lubrication points 9 2 Storage Unhitch the MANUBAL bale grab with the grab opened ram rod retracted Lubricate pivot points Coat the tines with oil Modification reserved MX Y 19 rue de Rennes BP 83221 F 35690 ACIGN 12 10 TECHNICAL SPECIFICATIONS Stacking height Number of bales picked up Bale diameter 6 bales H1 20m 1 bale H1 20m from 0 90 to 1 80 m Distance between tips Number of tines on grab 6 Overall height H 1610mm Grab height h 750 mm Width L 1625 mm Distance between tips In round bale setting 420 mm grab closed pf In rectangular bale setting 1 020 mm In round bale setting 1 510 mm In rectangular bale setting 1 570 mm Loader model grab opened po Tine diameter 25 mm Tine working length 1 340 mm 350 kg Wrapped bale diameter 1to1 60m Wrapped bale weight Up to 800 kg Min pivot height 3 45 m as from MX T6 Option MX 7 19 rue de Rennes BP 83221 F 35690 ACIGN Modification reserved 13 EC DECLARATION OF CONFORMIT
8. grab yourself or have it modified by anyone else without first requesting written authorisation from MX Failure to comply with these rules may render your MANUBAL bale grab hazardous In the event of damage or injury MX shall not be held responsible in any way Warranty cover will cease immediately in the event of failure to observe the standards and instructions for use and maintenance of the MANUBAL bale grab as stipulated in the user manual THE INSTALLER SHALL BE FULLY LIABLE FOR ANY FITMENT ON A LOADER OTHER THAN MX OR A TELESCOPIC HANDLER WHICH HAS NOT BEEN RECOMMENDED BY MX MX ZF 19 rue de Rennes BP 83221 F 35690 ACIGN 4 Modification reserved 2 SAFETY STICKERS Ensure the labels are clean and legible replace them if damaged 1 Location MANUBAL frame carrier Familiarise yourself with the safety rules in the user manual before using or working on the unit 3 IDENTIFICATION PLATE Identification details are to be passed on to your dealer with any request for spare parts or service work Its location is shown below 2 Location MANUBAL frame carrier MANUBAL identification data plate H H MX ce ER 2 z 19 rue de Rennes F 35690 ACIGNE a y A 9 D signation Designation Type Model Typ H E N de s rie AM
9. ing link in the appropriate hole Note check the spacers for correct positioning 7 6 Refit the clip 7 7 Repeat operations 7 3 to 7 6 for the cylinder end ram pin CAUTION the synchronising links should be removed from the MANUBAL bale grab when it is used for wrapped bales which allows the 2 grab arms to float This enhances effectiveness and safety when stacking bales contiguously 7 8 Position the first side of the wrapped bale grab kit U section against the grab tine carrier 7 9 Position the other side of the wrapped bale grab kit O section opposite the hole provided for this purpose in the MANUBAL grab 7 10 Insert the pin and the clip supplied in the kit 7 11 Repeat operations 7 8 to 7 10 for the other kit Note the kit is not handed as regards assembly It is identical for the left and right hand sides Option MX ZB 19 rue de Rennes BP 83221 F 35690 ACIGNE 10 Modification reserved 8 PRINCIPLE OF USE 8 1 Holding the bale on its cylindrical face 8 2 Holding the bale on its flat face MX 7 19 rue de Rennes BP 83221 F 35690 ACIGNE 11 Modification reserved 9 MAINTENANCE STORAGE 9 1 Maintenance Lubricate pivot points regularly See lubrication points below Ensure hydraulic connections are cleaned each time befor
10. rab lowered When notin use protruding items such as tine ends must be protected or stowed grab closed Check periodically to ensure that safety pins and bolts are in place Do not replace them with any other items such as nails wire etc Any adjustment on the MANUBAL bale grab ram position etc must be carried out after the MANUBAL bale grab has been lowered to the ground and the tractor engine shut down Any work involving fault tracing diagnostics and or disassembly of parts may only be undertaken by a skilled technician who will start with an assurance that the work will be carried out in complete safety for himself and his surroundings A Caution Check hoses for length and routing in all configurations fully crowded fully dumped etc before first use The MANUBAL bale grab is designed to withstand a maximum operating pressure of 210 bar Above this pressure the MANUBAL bale grab will require to be fitted with a pressure limiter Any instance of a MANUBAL bale grab being fitted which ignores the recommendations in the MX price list in force on the date of purchase will void MX warranty on the entire supply Any modification to any part of the MX supply rams grab tines crank etc or use of a component installed on the MANUBAL bale grab which has not originated from MX will void MX warranty on the entire MX supply Use only genuine MX spare parts Do not modify your MANUBAL bale
Download Pdf Manuals
Related Search