1.3 Location and description of major components and functions. 1
Contents
1. Screw Trigger in to the side connector of the laser unit 5 Attach Trigger pad to weapon using the Velcro lock Usual positions are on the pistol handle or over the thermal cover of the barrel using the supporting hand for activation 2 1 3 Installing the battery Open battery cover 6 Insert battery in the correct direction in the same way as you fit the battery in the red dot sight Make sure that the battery contacts are clean Close battery cover 2 2 OPERATING PROCEDURES 2 2 1 Selecting a laser Turn the selector 4 to the desired position The laser beam will only be activated once you press the switch pad Left Position Laser OFF Position 1 The Laser is at low power Position 2 The Laser is at high power 2 2 2 Switch pad trigger activation The laser must be on position 1 or 2 Pressing the Trigger switch activates the Laser When the switch is released the laser is interrupted 2 2 3 Adjustment of the Laser beam The laser can be adjusted horizontally and vertically Horizontal adjustment using the side located adjustment screws 3 Vertical adjustment using the adjustment screws located on top 2 To correct the point of impact proceed as follows e Turning the side adjustment screw in the direction moves the point of impact to the right e Turning the side adjustment screw in the impact to the left e Turning the top adjustment screw in the direction moves the point o2. CHAPTER 1 1 PRESENTATION The Aimpoint LPI IR Laser Aiming Device is a development based on long ex perience in engineering and manufacturing of lasers ranging from pistol to mili tary infantry rifle applications The Aimpoint LPI is intended to fit on AIMPOINT red dot sights which means that no special rail system is required The laser beam can be adjusted in X and Y axis independently The Aimpoint LPI is a truly unique tool light weight small and sturdy 1 2 SPECIFICATION Material housing Surface finish Housing width 44 mm 0 5 mm Housing height 24 mm 0 5 mm Overall housing length 47 5 2 mm 77 mm 2mm Weight incl battery 150 gr 5 3 oz Max temperature range 10 to 50 C 14 to 122 F Water resistance Submersible to 10 m water depth High strength Aluminum Anodized black Battery 3V Lithium battery of type DL1 3N 2L76 Mounting The Aimpoint LPI can be mounted with 4 different interfaces EN a N gi Ci z AY ees g eS fa WWS AA INA Setting The Laser has two different power settings to enable the selection of the power for short range or long range The performance of the night vision equipment used varies from manufacturer and the range for the low and high power will differ accordingly Light source Wavelength Beam output power Setting High 840 nm IR 0 1 mWw Setting Low 840 nm IR 0 005 mW Light source Beam Shape Beam diverg
3. ence Laser class Setting High 2x2 mm typ 0 5 mrad iss Setting Low 5x 2mm typ 0 5 mrad Adjustment of laser beam 1 Click 0 28 mrad Adjustment range of laser beam 20 mrad Unless indicated otherwise the data is accurate at ambient room temperature and normal operating conditions Typical Important notice Beam output power will be set as required by the user The user is solely responsible for the observation of the applicable safety regulations The max and the min level can be separated by a factor of no more than 20 1 3 Location and description of major components and functions Mounting screws Vertical adjustment screw Horizontal adjustment screw Power selector Off Contact for Remote switch pad trigger 7A Battery cover Lens cap NOOR WD CHAPTER II OPERATION 2 1 ASSEMBLY AND PREPARATION FOR USE WARNING Insure the weapon is unloaded and the safety selector is in the safe position before attempting to install remove or perform maintenance on the laser 2 1 1 Installing laser on the weapon Installing the laser on the sight or on the rail of the weapon The laser has to be fitted with the mount corresponding to the mount used on your red dot sight Remove the upper part of your red dot sight mount and fit the laser in its place as shown Use thread lock Loctite when assembling the laser to the mount with the 2 mounting screws 1 2 1 2 Installing remote switch pad trigger
4. f impact down e Turning the top adjustment screw in the impact up direction moves the point of direction moves the point of One click equals approx 3 cm at 100 m MAINTENANCE The LPI requires no routine maintenance When the lenses are soiled by dirt or gun powder residue a soft optical cloth is required to wipe the lens clean If required the reflection shields can be removed 7 Safety notice LASER beams can cause damage to the human eye Target lasers are for use by trained personnel only The user is responsible to maintain the safety precautions defined by local laws The use of this equipment is the sole responsibility of the operator z Aimpoint User s Manual for AIMPOINT LPI IR aiming laser device Aimpoint AB J gershillgatan 15 SE 213 75 Malm Sweden Phone 46 0 40 671 50 20 Fax 46 0 40 21 92 38 e mail info aimpoint se www aimpoint com Aimpoint Inc 14103 Mariah Court Chantilly VA 20151 2113 USA Phone 1 703 263 9795 Fax 1 703 263 9463 e mail info aimpoint com www aimpoint com THE FUTURE IN SIGHT 2008 Contents property of Aimpoint All rights reserved 11536 1
Download Pdf Manuals
Related Search