1 - TEquipment.NET
Contents
1. Insufficient load E onc cx e Load plate not on the scale e Weighing range not reached gt Place load plate on the scale gt Set fo zero Overload F 77777 e Weighing range exceeded gt Unload scale gt Reduce preload e Result not yet stable gt If necessary adjust vibration adapter or weigh dynamically e Function not permissible Unload scale and set to zero nng ER e Zeroing not possible with over gt Unload scale E n e E load or insufficient load hong J e No calibration gt Unplug the mains plug then plug it back in switch unit off and then back on in battery mode gt Calibrate scale gt Call OHAUS Service am e Printout not yet ended gt End printout gt Repeat required action e Switching the weighing unit impermissible during dynamic weighing gt End dynamic weighing gt Switch weighing unit e EAROM checksum error gt Unplug the mains plug then plug it back in switch unit off and then back on in battery mode gt Call OHAUS Service 34 Ranger RD Event and error messages Error Cause Remedy Weight display unstable e Restless installation location gt Adjust vibration adapter e Draft e Restless weighing sample e Contact between weighing pan and or weighing sample and surroundings e Mains fault gt Avoid drafts gt Dynamic weighing gt Remedy contact2. 6 Keyboard test e Press the keys ON OFF ZERO TARE PRINT Units Clear keys in order If the key works the scale changes to the next key Note You cannot abort the keyboard test If you have selected the menu item KboArd you must press all keys dISPLAY Display test The scale displays all functioning segments SNr Display of the serial number List Printout of a list of all menu settings rESEt AL SUrE Resetting all menu settings to the factory settings Confirmation inquiry e Reset all menu settings to the factory settings with Yes e Do not reset the menu settings with No 26 Ranger RD Interface description 4 Interface description 4 1 OHAUS interface commands The Ranger RD scales support the OHAUS command set With OHAUS commands it is possible to configure query and operate the scale from a PC 4 1 1 Available OHAUS commands Command Meaning 0S Set to print weight value immediately stable or unstable after P command 1S Set to print stable weight value after P command SA Set to print stable weight value automatically CA Set to print weight value continuosly XA Set to print weight value at specified interval where x 1 to 3600 seconds P Print displayed weight value Zero the scale Tare the scale XT Define the Preset Tare where x tare weight in grams H x y Define the Header H lt space gt x lt space gt
3. 67 09 26 Iceland 51 05 55 05 22 Ireland 35 47 47 05 17 Italy 55 30 58 04 23 Latvia 47 03 47 14 18 Liechtenstein 53 54 56 24 22 Lithuiania 49 27 50 11 20 Luxemburg 50 46 53 32 21 Netherlands 57 57 64 00 24 Norway 64 00 71 11 26 49 00 54 30 21 Poland 36 58 42 10 15 Portugal 43 37 48 15 18 Romania Ranger RD Appendix Geographical latitude Geo value Country 47 44 49 46 19 Slovakia 45 26 46 35 18 Slovenia 36 00 43 47 15 Spain 55 20 62 00 24 Sweden 62 00 69 04 26 45 49 47 49 18 Switzerland 35 51 42 06 16 Turkey 49 00 55 00 25 United Kingdom 55 00 62 00 23 factory setting 43 Appendix Ranger RD 44 7 3 2 GEO VALUES 6000e 7500e OIML Class III Height lt 1000 m Geograhical latitude Geo value 00 00 12 44 5 05 46 17 10 6 12 44 20 45 7 17 10 23 54 8 20 45 26 45 9 23 54 29 25 10 26 45 31 56 11 29 25 34 21 12 31 56 36 41 13 34 21 38 58 14 36 41 41 12 15 38 58 43 26 16 41 12 45 38 17 43 26 47 51 18 45 38 50 06 19 47 51 52 22 20 50 06 54 41 21 52 22 b7 04 22 54 41 59 32 23 57 04 62 09 24 59 32
4. Before connecting the scale to the mains check whether the voltage value printed on the rating plate corresponds with the local mains voltage A Never connect the device if the voltage value printed on the rating plate is different to the local mains voltage gt Plug the mains plug into the socket After connection the device performs a self test When the zero display appears the device is ready to weigh gt Calibrate the device in order to obtain the greatest possible precision see Section 3 3 1 Partially certified scales scales with first level certification must be certified by an authorised body or by the OHAUS Service Call OHAUS Service Scales with a built in battery can work independently from the mains for approxi mately 30 hours in normal operation A prerequisite for this is that the background lighting is switched off and that no peripheral devices are connected The device automatically switches to battery operation as soon as the mains supply is interrupted When the mains supply is restored the device automatically switches back to mains operation The battery symbol indicates the present charging level of the battery 1 segment cor responds to approx 25 capacity When the symbol flashes the battery must be charged min 4 hours The charging period is extended if work is continued during charging The battery is protected against overcharging The battery s charging capacity can be reduced und
5. play With dynamic weighing the scale calculates the mean value from 56 weighing oper ations within 4 seconds Prerequisite AVErAGE gt MAnuAL is selected in the menu The weighing sample must be heavier than 5 scale divisions 1 Place the weighing sample on the scale and wait until it has stabilized 2 Press PRINT to start dynamic weighing During dynamic weighing horizontal segments appear in the display and the dynamic result is then displayed with the symbol 3 Unload the scale to be able to start a new dynamic weighing operation Prerequisite AVErAGE gt AUtO is selected in the menu The weighing sample must be heavier than 5 scale divisions 1 Place the weighing sample on the scale The scale starts the dynamic weighing automatically During dynamic weighing horizontal segments appear in the display and the dynamic result is then displayed with the symbol 2 Unload the scale to be able to perform a new dynamic weighing operation Printing results If a printer or computer is connected to the scale the weighing results can be printed out or sent to a computer gt Press PRINT The display contents are printed out and transferred to the computer See Section 7 4 for sample protocols Operation Ranger RD A A 2 7 Cleaning CAUTION Electric shock hazard A Before cleaning with a damp cloth pull out the mains plug to disconnect the unit from the power supply CAUTION When
6. 2 weighing unit 19 Communication 23 Wight ise tc ciet 39 100 515 26 00601100 15 2 OVEFVI W oooi 17 ZBIOIDIga soot idc dut 11 Silena ar a a 19 Terminal 22 Menu structure 16 0 OHAUS commands 27 Operator menu se 15 Options o 5 24 46 Ranger RD Warranty LIMITED WARRANTY Ohaus products are warranted against defects in materials and workmanship from the date of delivery through the duration of the warranty period During the warranty period Ohaus will repair or at its option replace any component s that proves to be defective at no charge provided that the product is returned freight prepaid to Ohaus This warranty does not apply if the product has been damaged by accident or misuse exposed to radioactive or corrosive materials has foreign material penetrating to the inside of the product or as a result of service or modification by other than Ohaus In lieu of a properly returned warranty registration card the warranty period shall begin on the date of shipment to the authorized dealer No other express or implied warranty is given by Ohaus Corporation Ohaus Corporation shall not be liable for any consequential damages As warranty legislation differs from state to state and country to country please contact Ohaus or your local Ohaus dealer for further details 47 OHAUS TEquipment An
7. A CL tr ON OFF ZErO AZM OFF 0 5d 1d 2d 5d 104d 20 rEStArt ON OFF 20 FILtEr VibrAt LOW MEd HIGH 20 PrOCESS UNIVEr dOSING StABILI FASt StAndrd PrECISE FACt tEMP OFF 1K 2K 3K 5K 20 Min WEiG ON OFF ON OFF 21 rESEt SUrE 2 APPLIC AVErAGE OFF AUtO MAnuAL 21 rESEt SUrE 2 tERMINL dEVICE SLEEP OFF 1 min 3 min 5 min 22 PWr OFF YES NO b LIGHt ON OFF ACCESS SUPErVI 22 rESEt SUrE 22 COMMUNI COM 1 COM 2 MOdE Print 23 A Print CONt INU dIALOG CONt OLd dIAL OLd dt b GrOSS ON OFF tArE ON OFF nEt ON OFF Settings in the menu Ranger RD Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Page dt G GrOSS ON OFF tArE ON OFF nEt ON OFF COnt Wt 2nd dISP PriNtEr tEmPLat StdArd tEMPLt1 23 tEMPLt2 ASCi Fmt LINE FMt MULtI SINGLE LENGtH 1100 SEPArAt n Add LF 0 9 PArAMEt baud 300 38400 23 PAritY 7 nonE 8 nonE 7 odd 8 odd 7 EVEN 8 EVEN H SHAKE NO XONXOFF nEt 422 nEt 485 NEt Addr Ds 1 ChECSuM ON OFF Vcc ON OFF rSt COMx SUrE 24 COMMUNI OPtION EtH NEt IP AddrS SUbNEt GAtEWAY 24 USb USb tESt 24 diGitAL IN 1 4 OFF ZErO tArE 24 Print CLEAr Unit OUT 1 4 OFF StAbLE bEL Min AbV Min UndErLd OVErLd StAr dEF PrN tEmPLt1 LINE 1 NOt USEd HEAdEr 25 tEMPLt2 LINE 20 GrOSS tArE nEt StArLN CrLF F FEEd dIAGNOS tESt SC intErN ExtErN 26 KboArd dISP
8. RS232 Cable for Second Scale 80500526 RS232 Cable for SF42 Printer 80500571 Anti theft Device 80850000 Carrying Case for RD R 80850083 Carrying Case for RD L 80850084 Printer SF42 40 Ranger RD Appendix 7 Appendix 7 1 7 2 Information for certified scales in EC countries Weighing instruments verified at the place of manufacture bear the preceding mark on the packing label and green M sticker on the descriptive plate They may be set to work immediately Weighing instruments which are verified in two steps have no green M on the descriptive plate and bear the preceding identifaction mark on the packing label The second step of the verification must be carried out by the approved OHAUS Service or by the W amp M authorities Please contact OHAUS Customer Service The first calibration step of the verification has been carried out at the manufacturing plant It comprises all tests according to EN45501 8 2 2 Scales with analog connec tion to the weighing platform require an additional test according to EN45501 3 5 3 3 However this test is not mandatory if the terminal bears the same serial number as the weighing platform If national regulations in individual countries limit the period of validity of the certifica tion the operator of such a scale is himself responsible for its timely re certification Safety checks The compact scales of the Ranger RD series have been chec
9. USA TE t 9 Equipment oe Interworld Highway LLC NET OHAUS Ranger RD Compact Scales Instruction Manual Ranger RD Table of contents Table of contents C Co N 2 1 2 2 2 3 2 4 2 5 2 6 2 7 3 1 3 2 3 3 3 4 3 5 3 6 3 7 4 1 4 2 4 3 6 1 6 2 7 1 7 2 7 3 7 4 Page fol 119 116 poseen cc 4 Safety IMS r r 4 9 0101100 P 5 Putting into 665162 9 Operation isss 2 2 ioco anaa a naaa ka 11 Switching 0 60 6 Ol uscite rem ca d eat ch Y tele ei 11 Zeroing Zero point correction seis dod ND ews Pad RE Rte in Dd aen 11 OPEN a eoa eat aba Pap rg od dca tcl to RDUM an a 11 Weighing With TELE kasakska Doe codi hd eb oti ias 12 Dynamic 262 10 13 Piinting SS asad sand aida edt up oth dodo coda ad btt inte Dads M Ea ERU nine 13 EA a aan 14 Settings in thi MON nn kk nan nnam nares 15 Operating The 15 OVOTVIOWE iera bol t abd aa abut tai e eta 17 Scale sallitids GAME a 19 Application settings APPLICATION 21 Terminal settings TERMINAL ica Atar a a a t veta dee Pt codage 22 Configuring interfaces COMMUNICATION 23 Diagnosis and printing out of the menu settings DIAGNOS 26 Interface 6630101100 ci cic noch weeds nakin lunar a 27 OHAUS interface COMMONS ax cese see rtr teer a et e ets 27 SICS interface commandS rss faber rip ed d pte 29 TOLEDO Continuous mode eoi cita room ra A ne
10. gt Check mains Incorrect weight display e Incorrect Zeroing e Incorrect tare value e Contact between weighing pan and or weighing sample and surroundings e Scale tilted gt Unload scale set to zero and repeat weighing operation gt Clear tare gt Remedy contact Level scale 35 Technical data and accessories Ranger RD 6 Technical data and accessories 6 1 Technical data 6 1 1 Type key The Ranger RD compact scales are available with various capacities and platforms that can be seen from the complete type designation Example RDGRS compact scale with capacity 6 kg and small platform RD35LM compact scale with capacity 35 kg and large platform RD3SM compact scale with capacity 3 kg and extra small platform 6 1 2 General data RD S RD S IP RD M Applications e Weighing e Dynamic weighing Settings e Resolution selectable e Weighing unit selectable g kg oz Ib t e Taring function manual automatic chain tare e Automatic zero point correction when the scale is switched on and during oper ation e Filter for adapting to the ambient conditions vibration adapter e Filter for adapting to the weighing type e g dispensing weighing process adapter e Switch off function sleep mode for mains operated devices energy saving mode for battery operation e Display lighting Accuracy class OIML NTEP e RD S Ill e RD M Display e LCD liquid crystal display digits 1
11. Interworld Highway LLC NET P N 22017161 2007 Ohaus Corporation all rights reserved Printed in Germany
12. RD S D1335 265 100 240 200 46 276 208 216 165 165 RD R D 335 265 100 240 200 46 276 208 216 l RD L 370 360 115 350 240 92 310 304 310 D Dimenions in mm 6 1 6 Net weights Model without battery with battery with internal calibration weight without battery RD RS 4 6 kg 5 3 kg E RD RS IP 4 7 kg 5 4 kg RD LS 8 2 kg 8 9 kg z RD LS IP 8 3 kg 9 0 kg RD SM 4 9 kg 5 6 kg 5 4 kg RD RM 4 7 kg 5 4 kg 5 2 kg RD LM 10 5 kg 11 2 kg 11 7 kg 39 Technical data and accessories Ranger RD 6 1 7 Interface connections The compact scale can be fitted with a maximum of 2 interfaces The following com binations are possible COMI COM2 Note RS232 RS232 RS232 RS485 RS232 COMI can be optionally operated as RS422 or RS485 RS232 Ethernet not for RD S IP RS232 USB RS232 Digital I O 6 1 8 Assignment of the interface connections Pin RS232 RS422 RS485 Digital 1 0 COM1 COM2 4 wire COMI 2 wire COM1 COM2 es B GND 2 TxD1 2 TxD1 TxD1 RxD1 OUTO 3 RxD1 2 RxD1 OUTI 4 x OUT2 5 GND GND GND OUT3 6 INO 7 TxD1 TxD1 RxD1 INT 8 RxD1 IN2 9 VCC VCC VCC IN3 6 2 Accessories Designation Order number In Use Cover for RD R 21203719 In Use Cover for RD L 21203720 RS232 Cable for PC 80500525
13. in the display If A CL tris activated in the menu the tare weight is automatically cleared as soon as the scale is unloaded Automatic taring Prerequisite A tArE is activated in the menu the symbol T flashes in the display gt Place the container or packaging material on the scale The packaging weight is automatically saved as the tare weight the zero display and the symbol NET appear Chain tare Prerequisite The tare function CHAIn tr is activated in the menu With this function it is possible to tare several times if for example cardboard is placed between individual layers in a container 1 Place the first container or packaging material on the scale and press TARE The packaging weight is automatically saved as the tare weight the zero display and the symbol NET appear 2 Weigh the weighing sample and read print out the result 3 Place the second container or packaging material on the scale and press TARE again The total weight on the scale is saved as the new tare weight The zero display appears 4 Weigh the weighing sample in the second container and read print the result b Repeat the last two steps for other containers Ranger RD Operation 2 5 With manual start With automatic start 2 6 Dynamic weighing With the dynamic weighing function it is possible to weigh restless weighing samples such as live animals If this function is activated the symbol amp appears in the dis
14. unit and repeat after every weight change SRU Send weight value in the current unit and repeat ST After pressing the Transfer key send the stable weight value SU Send stable weight value in the current unit 1512 Start test function with external weight TST3 Start test function with internal weight LEVEL SPECIAL CLR Clear 13 Header for the printout ICP Send configuration of the printout LST Send menu settings MOI Weighing mode M02 Stability setting MO3 Autozero function M19 Send calibration weight M21 Inquire set weight unit P Print text P130 Weight value unit and price PRN Print out at every printer interface RST Restart SFIR Send weight value immediately and repeat quickly SIH Send weight value immediately in high resolution SWU Switch weight unit SX Send stable data record SXI Send data record immediately SXIR Send data record immediately and repeat U Switch weight unit 30 Ranger RD Interface description 4 2 2 4 2 3 Requirements for communication between scale and PC The scale must be connected to the RS232 RS485 USB or Ethernet interface of a PC with a suitable cable The interface of the scale must be set to Dialog mode see Section 3 6 1 A terminal progam must be available on the PC e g HyperTerminal The communication parameters baud rate and parity must be set in the terminal program and on the scale to the same values see Section 3 6 3 Notes on network operation via the optional inter
15. y where x 1 2 3 4 5 line number and y header text in quotes up to 24 characters PSI Change to MT SICS command set POH Return to OHAUS command set NOTE All commands must be followed by a carriage return line feed lt CR gt lt LF gt 4 1 2 Requirements for communication between scale and PC e The scale must be connected to the RS232 RS485 USB or Ethernet interface of a PC with a suitable cable e The interface of the scale must be set to Dialog mode see Section 3 6 1 e A terminal progam must be available on the PC e g HyperTerminal e The communication parameters baud rate and parity must be set in the terminal program and on the scale to the same values see Section 3 6 3 4 1 3 Notes on network operation via the optional interface RS422 485 Up to 32 scales can be networked with the optional RS422 485 interface In network operation the scales must be addressed from the computer before commands can be sent and weighing results received 27 Interface description Ranger RD 4 1 4 Output format Response to the P command Field 1 2 3 4 5 6768 10 POL SP SP W WWW WI WI WI SPJUN UN SP STISP N N N CR LF c Field 1 POL polarity space if positive if negative Fields 2 4 6 8 SP space Field 3 W weight up to 6 digits plus the decimal point Field 5 UN unit of measure 1 or 2 characters Field 7 ST stabil
16. 6 mm high with back lighting Keypad e Pressure point membrane keypad e Scratch proof labeling Housing e Diecast aluminum housing chromium nickel steel weighing pan e Dimensions see Page 37 Protection Class IEC 529 e 10 5 RD M IP43 not with Ethernet interface DIN 40050 EN60529 e RD SIP IP65 36 Ranger RD Technical data and accessories RD S RD S IP RD M Mains connection Direct connection to the mains MAINS supply voltage fluctuations up to 10 of the nominal voltage e 230 V 50 Hz 70 mA e 240 V 50 Hz 70 mA e 120 V 60 Hz 90 mA e 100 V 50 60 Hz 90 mA For battery operation e Connection via mains adapter 90 264 V 47 63 Hz 300 mA e infeed on the unit 24 V 1 3A Battery operation If the voltage supply is interrupted the unit automatically switches over to battery operation Ambient conditions e Use Indoor use only e Altitude up to 2000 m e Temperature range RD S 10 40 C 14 104 F e Temperature range RD M 10 30 C 50 86 F e Overvoltage category ll e Contamination level 2 e Relative humidity Maximum relative humidity 80 for temperatures up to 31 C 88 F decreasing linearly to 50 relative humidity at 40 C 104 F Interfaces e RS232 interface integrated e 1 other optional interface possible 37 Technical data and accessories Ranger RD 6 1 3 Weighing ranges and
17. 64 55 25 62 09 67 57 26 64 55 71 21 27 67 57 75 24 28 71 21 80 56 29 75 24 90 00 30 Ranger RD Appendix 7 4 Sample protocols Weighing with tare Dynamic weighing Printout with header G 0 1085 kg Dyn WT 43 52 kg OHAUS CORP T 0 0145 kg T 3 78 kg www ohaus com N 0 0940 kg G Gross weight G 0 1085 kg N Net weight T 0 0145 kg T Tore N 0 0940 kg Dyn WT dynamically determined weight Protocol of the scale settings menu point List see page 26 SOFTWARE VER 7 0 1 01b COMMUNICATION SCALE COM 1 MODE 1 Print METROLO NO APPr PriNtEr SNR 0000000 tEmPLat 1 StdArd Scale Build ASCi Fmt SCAL TYP 2MULT RN LINE FMT1 MULTI BAS UNIT kg LENGtH 1 0 SCL CAP1 1 5000 kg ADD LF 1 0 RESOL 1 0 0005 kg PARAMET SCL CAP2 3 000 kg BAUD 1 9600 RESOL 2 0 001 kg PAriTY 1 8 nonE GEO 219 H SHAKE 1 XONXOFF DISPLAY ChECSUM 1 OFF UNIt1 kg Vec 1 0FF UNIt2 eg COM 2 RESOLU 0 0005 kg MODE 2 DIALOG UNt rOLL ON PARAMET tArE BAUD 2 9600 A TArE OFF PAriTY 2 8 nonE CHAIn tr OFF H SHAKE 2 XONXOFF A CL tr OFF ChECSUM 2 0FF PB TArE ON Vcc 2 0FF ZERO OPTION Z CAPT 2 18 EtH NEt N A AZM 2d USB N A RESTART ON DEF PrN FILTER tEmPLt1 VIBRAT MED LINE 1 HEAGEr PROCESS UNIVEr LINE 2 CrLF StABILI FASt LINE 3 GROSS Min WEiG LINE 4 tArE SEt VAL 0 200 kg LINE 5 n
18. Et ONOFF OFF LINE 6 F FEEd LINE 7 STARLN APPLICATION LINE 8 CrLF e 2 tEmPLt2 DYNAMIC OFF TERMINAL DEVICE SLEEP OFF B LIGHt OFF 45 Index Ranger RD 8 Index A P Accessories 40 Password eene 15 AO 19 Power supply na 10 Aa nc oet fs 9 n PrO Olea ds 13 Ambient conditions 37 R 00110011005 36 Ma oir 13 2 Re dobiliy sss 38 Reset C AB 21 Calibrate 5 a ado bet aa nin peered 19 Interface 24 Chain 10 12 Scale i 2 Continuous mode 31 Terminal 22 D RS422 RS485 o cierto 31 Dimensions 39 S Display on ios ceto FK Sks 4 Display accuracy 19 Sample protocols 45 Dynamic weighing 13 21 Soeales Iybes stes 5 SONOS anna 36 E SICS commands 29 Error 6586063 34 Supervisor menu 15 F Switching 0 11 20 Switching Oh 11 I T Interfaces Tare Configure PM CAT 23 Automatic sss 12 Connections 40 Chain 1018 12 Gla a stenst tagi 12 K Terminal settings 22 Keyboard eee 8 TOLEDO Continuous 31 M TUBOS KU ooi ala 36 Mains connection 37 W Menu Weighing ranges 38 Application
19. Insufficient load OVErLd e Overload StAr e Changed calculated value 24 Ranger RD Settings in the menu 3 6 6 DEF PRN configuring templates tEMPLt1 tEMPLt2 Selecting Template 1 or Template 2 LINE 1 20 Selectline NOt USEd e Line not used HEAdEr e Line as header The contents of the header must be defined via an interface com mand see Section 4 1 GROSS e Gross weight tArE e Tare weight nEt e Net weight StARLN e Line with CrLF e Line feed blank line F FEEd e Page feed 25 Settings in the menu Ranger RD 3 7 Diagnosis and printing out of the menu settings DIAGNOS tESt sc Internal External Testing scale with internal calibration weight Int CAL appears in the display during the test e After completion of the test ideally d 0 Og briefly appears in the display after which the scale changes to the next menu ifem KboArd Testing scale with external calibration weight 1 The scale checks the zero point 0 appears in the display The test weight flashes in the display If necessary change the weight value displayed with No Put the calibration weight on the scale and confirm with Yes The scale checks the calibration weight put on them After the test is completed the deviation from the last calibration briefly appears in the display ideally d 0 Og after which the scale changes to the next menu item KboArd or O N KboArd PUSH 1
20. LAY SNr List rESEt AL SUrE Ranger RD Settings in the menu 3 3 Scale settings SCALE 3 3 1 CAL calibration adjustment This menu item is not available for certified scales without internal calibration weight Internal For scales with an internal calibration weight 1 Unload scale 2 Activate menu item CAL with Yes The scale calibrates with the internal cali bration weight Int CAL appears in the display After calibration is completed donE appears briefly in the display and the scale automatically returns to weighing mode External For scales without an internal calibration weight 1 Unload scale 2 Activate menu item CAL with Yes The scale determines the zero point 0 appears in the display The calibration weight to be placed on the scale then flashes in the display 3 If necessary change the weight value displayed with No 4 Place the calibration weight on the scale and confirm with Yes The scale calibrates with the calibration weight loaded After calibration is com pleted donE appears briefly in the display and the scale automatically returns fo weighing mode 3 3 2 DISPLAY weighing unit and display accuracy UNIt1 Select weighing unit 1 g kg 02 Ib t UNIt2 Select weighing unit 2 g kg oz Ib t rESOLU Select readability resolution model dependent UNt rOLL When UNT rOLL is switched on the weight value can be displayed i
21. OG Bi directional communication via OHAUS or MT SICS commands control of the scale via PC CONt OLd As per CONt INU see above but with 2 fixed blanks in front of the unit compatible with Spider 1 2 3 dIAL OLd As per dIALOG see above but with 2 fixed blanks in front of the unit compatible with Spider 1 2 3 dt b DigiTOL compatible format GROSS e Transfer of the gross weight identified with G tArE e Transfer of the tare weight nEt e Transfer of the net weight dt G As per dt b see above gross weight identified with G COnt Wt TOLEDO Continuous mode 2nd dISP For connecting a second display automatically activates the 5 V voltage supply at Pin 9 3 6 2 COM1 COM2 gt PRINTER settings for protocol printout This menu item only appears if the mode Print or A Print is selected tEmPLat Selecting protocol printout StdArd e Standard printout tEmPLt1 e Printout in accordance with Template 1 tEmPLt2 e Printout in accordance with Template 2 ASCi FmtT Selecting formats for the protocol printout LINE Fmt e Line format MULtI multi line or SINGLE single line LENGtH e Line length O 100 characters appears only with line format MULtI SEPArAt e Separator _ and space appears only with line format SINGLE Add LF e Line feed 0 9 3 6 3 COM1 COM2 gt PARAMET communication parameter bAUd Selecting baud rate 300 600 1200 2400 4800 9600 19200 38400 baud PAritY Selecting parity 7 none 8 none 7 odd 8 odd 7 even 8
22. d operate the scale from a PC SICS commands are divided up into various levels To use the MT SICS commands first send the OHAUS command PSI To return to the OHAUS command set send the OHAUS command POH 4 2 1 Available SICS commands Command Meaning LEVEL O Reset the scale I0 Inquiry of all available SICS commands Inquiry of SICS level and 5105 versions 12 Inquiry of scale data I3 Inquiry of scale software version 14 Inquiry of serial number S Send stable weight value SI Send weight value immediately SIR Send weight value repeatedly Z Zero the scale Zl Zero immediately LEVEL 1 D Write text into display DW Weight display K Keyboard check SR Send and repeat stable weight value T Tare TA Tare value TAC Clear tare TI Tare immediately LEVEL 2 C2 Calibrate with the external calibration weight C3 Calibrate with the internal calibration weight 110 Inquire or set scale ID 111 Inquiry of scale type P100 Print out on the printer 29 Interface description Ranger RD Command Meaning P101 Print out stable weight value P102 Print out current weight value immediately PWR Power On Off SIRU Send weight value in the current unit immediately and repeat SIU Send weight value in the current unit immediately SNR Send stable weight value and repeat after every weight change SNRU Send stable weight value in the current
23. e available in a small and large size in various capacities and resolutions The power supply is carried out via a built in power supply device an internal rechargeable battery with an external mains adapter or an external battery One of the following options can also be ordered Additional interface RS232 or RS485 e Ethernet interface e USB interface Digital I O Introduction Ranger RD 1 2 1 Overview 1 Display 2 Scale specifications 3 Load plate 4 Adjustable foot 5 Keys 1 Power supply connection 2 Fastand fine pressure equalization only with Protection Class IP65 3 Optional interface 4 RS232 interface Ranger RD Introduction 1 2 2 Display Active interface Weighing range display Battery charge level only present on scales with a battery Symbol for displaying net values Symbol for dynamic weighing Weight units 7 segment display 7 digits with decimal point Stability monitor goes out when a stable weight value is reached Sign 0 Identification for changed or calculated weight values e g higher resolution minimum weight not reached on oO oF WN Introduction Ranger RD 1 2 3 Keypad Main functions Key Function in operating mode Function in the menu Switching device on off abort Exi To the last menu item End Setting scale to zero DIO Back Scrolling back Taring scale 2 Scrolling forward Transfer key Long key press Ca
24. ed when the device is first delivered Therefore respond to the password inquiry with MENU when you call up the menu for the first time If a password has still not been entered after a few seconds the scale returns to weigh ing mode Emergency password for Supervisor access to the menu If a password has been issued for Supervisor access to the menu and you have for gotten it you can still enter the menu gt Press ZERO 3 times and confirm with Yes Settings in the menu Ranger RD 3 1 2 Selecting and setting parameters Back APPLIC No Yes Back Back No Back No Back Back No Back No Back Yes Yes Yes Yes Yes Yes Yes Scrolling on one level gt Scroll forward Press No gt Scroll back Press Back Activating menu items gt Press Yes accepting selection Exiting menu 1 Press Exit The last menu item END appears 2 Press Yes The inquiry SAVE appears 3 Confirm inquiry with Yes to save the settings and return to weighing mode or gt Press No to discard changes and return to weighing mode Ranger RD Settings in the menu 3 2 Overview Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Page SCALE CAL 19 dISPLAY UNIt1 g kg oz lb t 19 UNIt2 g kg oz lb t rESOLU UNt rOLL ON OFF tArE A tArE ON OFF 19 ChAIn tr ON OFF
25. er continuous mains operation gt To maintain the charging capacity after a maximum of 4 weeks discharge the bat tery completely before recharging it Ranger RD Operation 2 Operation 2 1 Switching on Switching off 2 2 Manual Automatic 2 3 Switching on and off gt Press ON OFF The scale conducts a display test When the weight display appears the scale is ready to weigh gt Press ON OFF Before the display goes out OFF appears briefly Zeroing Zero point correction Zeroing corrects the influence of slight changes on the load plate 1 Unload scale 2 Press ZERO The zero display appears In the case of scales that cannot be certified the automatic zero point correction can be deactivated in the menu or the amount can be changed As standard the zero point of the scale is automatically corrected when the scale is unloaded Simple weighing 1 Place weighing sample on scale 2 Wait until the stability monitor goes out 3 Read weighing result Operation Ranger RD 2 4 2 4 1 2 4 2 2 4 3 2 4 4 Weighing with tare Taring gt Place the empty container on the scale and press TARE The zero display and the symbol NET appear The tare weight remains saved until it is cleared Clearing the tare gt Unload scale and press TARE The symbol NET goes out the zero display appears or gt Press Clear The symbol NET goes out the gross weight appears
26. even H SHAKE Selecting Handshake NO XONXOFF nEt422 nEt485 network operation as per RS485 standard via the optional RS422 RS485 interface only for COM1 23 Settings in the menu Ranger RD NET Addr Assigning network address 0 31 only for NET 485 ChECSuM Activating checksum byte appears only in TOLEDO Continuous mode Vcc Switching 5V voltage e g for a bar code reader on off 3 6 4 COMI CON2 gt RESET COMT RESET COM2 resetting serial interface to factory settings SUrE Confirmation inquiry e Reset interface settings to factory settings with Yes e Do not reset the interface settings with No 3 6 5 OPTION configuring options If no option is installed or is not yet configured N A appears in the display EtH NEt Configuration of the Ethernet interface IP AddrS e Enter IP address SUBNEt e Enter Subnet address GAtEWAY e Enter Gateway address USb Configuration of the USB interface USb TEST e Test of the USB interface After the test has been passed rEAdy appears in the display diGitAL Configuration of the digital inputs outputs INL x24 Configuring inputs 1 4 OFF e Input not assigned ZErO e ZERO Key tArE e TARE Key PriNt e PRINT Key CLEAr e Clear Key UNIt e Units Key GUT L sss 4 e Configuring outputs 1 4 OFF e Output not assigned StAbLE e Stable weight value bEL MIN e Minimum weight not reached AbV MIN e Minimum weight reached or exceeded UNdErLd e
27. face RS422 485 Up to 32 scales can be networked with the optional RS422 485 interface In network operation the scales must be addressed from the computer before commands can be sent and weighing results received Description of the steps Host Direction Scale 1 Host addresses the scale e g with the address lt ESC gt 3A gt 3A hex Host sends a SICS command e g SI SI lt CRLF gt gt The scale confirms receipt of the command and lt lt ESC gt 3A sends the address back 4 The scale responds to the command and returns lt SS 45 02_kg control of the bus to the host lt CRLF gt 31 Interface description Ranger RD 4 3 TOLEDO Continuous mode 4 3 1 TOLEDO Continuous commands The scale supports the following input commands in TOLEDO Continuous mode Command Meaning P lt CR gt lt LF gt Print out the current result T lt CR gt lt LF gt Tare the scale Z lt CR gt lt LF gt Zero the display C lt CR gt lt LF gt Clear the current value Tx xxx lt CR gt lt LF gt Define tare 4 3 2 Output format in TOLEDO Continuous mode Weight values are always sent in the following format in TOLEDO Continuous mode Status Field 1 Field 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 STX SWA SWB SWC MSD LSD MSD LSD CR CHK Field 1 6 digits for the weigh
28. irmation inquiry e Reset the scale settings to factory settings with Yes e Do not reset scale settings with No 3 4 Application settings APPLICATION 3 4 1 AVERAGE determining the average weight for an unstable load OFF Calculating average weight switched off AUtO Calculating average weight with automatic start of the weighing cycle MAnuAL Calculating average weight with manual start of the weighing cycle via PRINT 3 4 2 RESET resetting application settings to factory settings SUrE Confirmation inquiry e Reset the application settings to factory settings with Yes e Do not reset the application settings with No 21 Settings in the menu Ranger RD 3 5 3 5 1 Terminal settings TERMINAL DEVICE Sleep mode energy saving mode and display backlighting SLEEP This menu item only appears on devices in mains operation When SLEEP is activated the scale switches off display and backlighting after the time period set when not in use The display and backlighting are switched on again at the press of a key or if the weight changes Possible settings OFF 1 min 3 min 5 min PWr OFF This menu item only appears on devices in battery operation When Pwr OFF is activated the device switches itself off automatically after approx 3 minutes when not in use b LIGHt Switching the display backlighting on off On scales with a battery the background lighting switches itself off automatica
29. ity status space when stable when unstable Field 9 N NET or B G Field 10 CR LF carriage return line feed Response fo the Print key Line Field 1 2 3 1 S C A L E SP SC CR LF 1 2 3 4 5 6 78 9 2 GC SP SP SP SP SP SP SP SP SP SP SP SP SP POLWIW W WF WWW WI SP UN UN SP ST CR LF 3 T SP SP SP SP SP SP SP SP SP SP SPSP SP POLWIWW W WW W SPIUNIUNSP 0 1 4 N SP SP SP SP SP SP SP SP SP SP SP SP SP POL W W WIW W W WI SP UN UN SP ST CR LF Line 1 Field 1 SCALE SP heading and space Field 2 SC scale identifier 1 scale 1 2 scale 2 Field 3 CR LF carriage return line feed Lines 2 3 4 Field 1 G Gross T Tare N Net Field 2 SP space up to 13 Field 3 POL polarity space if positive if negative Field 4 W weight up to 6 digits plus the decimal point Field 5 7 SP space Field 6 UN unit of measure 1 or 2 characters Field 8 ST stability status space when stable when unstable does not apply to Line 3 Field 9 CR LF carriage return line feed 28 Ranger RD Interface description 4 2 SICS interface commands The Ranger RD compact scales support the command set MT SICS METTLER TOLEDO Standard Interface Command Set With MT SICS it is possible to configure query an
30. ked by accredited testing institutions They have passed the safety checks listed below and carry the relevant test symbols Production is subject to production monitoring by the inspection offices Country Test symbol Standard Canada CAN CSA C22 2 No 1010 1 92 USA GR UL Std No 61010A 1 C US Other countries CB Scheme IEC EN61010 1 2001 no identification 41 Appendix 42 7 3 7 3 1 Table of Geo Values For weighing instruments verified at the manufacturer s the geo value indicates the country or geographical zone for which the instrument is verified The geo value set in the instrument e g Geo 18 appears briefly after switch on or is specified on a label Table GEO VALUES 3000e shows the geo values for European countries Table GEO VALUES 6000e 7500e shows the geo values for different gravitation Zones GEO VALUES 3000e OIML Class III European Countries Geographical latitude Geo value Country 46 22 49 01 18 Austria 49 30 51 30 21 Belgium 41 41 4413 16 Bulgaria 42 24 46 32 18 Croatia 48 34 51 03 20 Czechia 54 34 57 45 23 Denmark 57 30 59 40 24 Estonia 59 48 64 00 20 Finland 64 00 70 05 26 41 20 45 00 17 France 45 00 51 00 19 47 00 55 00 20 Germany 34 48 41 45 15 Greece 45 45 48 35 19 Hungary 63 17
31. lling up menu wu Ye D Activating menu item Accepting selected setting Additional functions Key Function Switching weight unit Clear key Ramger RD Introduction Major geographical location changes Putting into operation Selecting or changing the location The correct location is crucial to the accuracy of the weighing results gt Select a stable vibration free and if possible a horizontal location The ground must be able to safely bear the weight of the fully loaded scale Observe the following environmental conditions e No direct sunlight e No strong drafts e No excessive temperature fluctuations Aligning the scale Only scales that have been aligned precisely horizontally provide accurate weighing results The certified scales have a spirit level to simplify alignment gt Turn the adjustable feet of the scale until the spirit level s air bubble is inside the inner circle The manufacturer adjusts each scale to the local gravity conditions GEO value In the event of major geographical location changes this setting must be adjusted by a service technician Certified scales must also be recertified observing the national cer tification regulations These steps are not necessary for scales with an internal cali bration weight Introduction Ranger RD 1 3 2 A Note Note Connecting the power supply CAUTION
32. lly if there has been no activity on the scale for 5 seconds Note This menu item is accessible without a Supervisor password 3 5 2 ACCESS password for Supervisor menu access SUPErVI ENtER C rEtYPE C Password entry for Supervisor menu access Request to enter password gt Enter the password and confirm with Yes Request to repeat the password entry gt Enter the password again and confirm with Yes Notes e The password can consist of up to 4 characters e The PRINT key must not be part of the password It is required for confirming the password e The key ZERO may only be used in combination with another key e f you enter an impermissible code or make a typing error in the repetition COdE Err appears in the display 3 5 3 RESET resetting terminal settings to the factory settings SUrE Confirmation inquiry e Reset terminal settings to the factory settings with Yes e Do not reset the terminal settings with No 22 Ranger RD Settings in the menu 3 6 Configuring interfaces COMMUNICATION 3 6 1 COM1 COM2 gt MODE operating mode of the serial interface Print Manual data output to the printer with PRINT A Print Automatic output of stable results to the printer e g for series weighing operations CONt INU Ongoing output of all weight values via the interface dIAL
33. n all available units with Units Notes e On certified scales the weighing units oz and Ib are displayed with the symbol e On certified scales resolutions that deviate from the scale definition are displayed without a weighing unit and with the symbol e On dual range dual interval scales resolutions marked with I 1 21 are divided up into 2 weighing ranges intervals e g 2 x 3000 d 3 3 3 TARE tare function A tArE Switching on off automatic taring CHAIn tr Switching on off chain tare A CL tr Switching on off automatic taring with automatic clearing of the tare weight when the load is removed from scale Settings in the menu Ranger RD 3 3 4 ZERO automatic zero update AZM On certified scales this menu item does not appear Switching on off automatic zero update and selecting zeroing range Possible settings OFF 0 5 d 1d 2d 5d 10d 3 3 5 RESTART automatic saving of zero point and tare value ON OFF When the Restart function is activated the last zero point and tare value are saved After switching off on or after a power interruption the device continues to work with the saved zero point and tare value 3 3 6 FILTER adaptation to the ambient conditions and the weighing type VIbrAt Adaptation to the ambient conditions LOW e Very steady and stable environment The scale works very quickly but is very sensitive to external influences MEd e Normal en
34. n on vos dt 32 Event and error messages eeeeeeeeeeneneneeneenennnne nnn 34 Technical data and accessories eeeeeeeenee 36 TEN PPP 36 PG COSSONES Mr MEO MP 40 pon ger CD 41 Information for certified scales in EC countries 000 4 Safety NSS apana a a a ada aM 4 Table OF Geo VOlllGS a tuisse idet e tel doe Fat ta cae 42 Sample protocols oet htt Dee re tU ib P eve te 45 Lt dem cc ER 46 Introduction Ranger RD 1 Introduction X gt A 1 1 Safety instructions CAUTION Do not use RD S RD S IP65 RD M in hazardous areas Our product range includes special devices for hazardous areas CAUTION Use only scales with Protection Class IP65 if e the scale is used in wet areas e wet cleaning is necessary e the scale is used in a dusty environment Even with Protection Class IP65 the scale must not be used in environments with cor rosion risk A Never flood the scale or immerse it in liquid DANGER Electric shock hazard A Always pull out the mains plug before any work on the device DANGER Electric shock hazard if the mains cable is damaged A Check the mains cable for damage regularly and replace it immediately if it is dam aged A On the rear side of the device maintain a clearance of at least 3 cm in order to prevent the mains cable bending too much CAUTION On no account open the device The
35. readability RD S The RD S compact scales with strain gauge weighing cells are supplied in the configuration 2 x 3000 d Higher readabilities are available from the factory with the optional Premium weighing cells Capacity Configuration 2 x 3000 d standard 1 x 6000 d with optional Premium weighing cells Weighing Readability Weighing Readability ranges certified range certified 3 kg 1 5 kg 3 kg 0 5g 1g 3 kg 0 5g 6 kg 3 kg 6 kg 1g 2g 6 kg lg 15 kg 6 kg 15 kg 29 5g 15 kg 2g 35 kg 15kg 35kg 59g 10g 35 kg 5g 60 kg 30 kg 60 kg 10g 20g 60 kg 10g 6 1 4 Weighing ranges and readability RD M Configurations up to 1 x 60 000 e are possible with the RD M compact scales with MonoBloc technology Certified RD M compact scales are supplied as standard with an internal calibration weight Model Weighing interval s Readability d Verification value e RD3DSM 600 g 3 100g 0 01 g 0 1g 0 1g RD3SM 3 100 g 0 01 0 1g RDGDSM 1 200 g 6 100 g 0 01 g 0 1g 0 1g RD6SM 6 100 g 0 01 0 1g RD6DRM 1 200 g 6 100 g 0 1g 1g lg RD6RM 6 100g 0 2g 0 2g RD15DLM 3 500g 15 100g 0 1g 1g lg RD15LM 15 100 g 0 59g 0 5g RD35DLM 7 000 g 35 100g 0 1g 1g lg RD35LM 35 100 g 0 1g lg 38 Ranger RD Technical data and accessories 6 1 5 Dimensions A B c D E F G H K L
36. t value that is sent without a decimal point and unit Field 2 6 digits for the tare weight that is sent without a decimal point and unit STX ASCII characters 02 hex characters for start of text SWA SWB SWC Status words A B C see below MSD Most significant digit LSD Least significant digit CR Carriage Return ASCII characters OD hex CHK Checksum 2 part complement of the binary sum of the 7 lower bits of all previously sent characters incl STX and CR 32 Ranger RD Interface description Status word A Status Bit Function Selection 6 5 2 1 0 Decimal X00 0 0 0 0 position XO 0 0 X 0 0 0 X 0 0 0X 0 0 0 00X 0 0 000X 0 0 0000X Numerical X1 increment y Xb Status word B Status word C Function value Bit Function value Bit Gross net Net 1 0 0 0 Sign Negative 1 0 Overload 1 2 0 2 Movement 1 3 Print request 1 3 Ib kg kg 1 4 Extended 1 4 5 5 Powerup 1 6 Manual taring only kg 1 6 33 Event and error messages Ranger RD 5 Event and error messages Error Cause Remedy Display Dark e Back lighting set too dark e No mains voltage e Unit switched off e Mains cable not plugged in e Brief fault gt Set back lighting b LIGHt brighter gt Check mains Switch on unit gt Plug in mains plug Switch device off and back on again
37. the weighing pan has been removed never clean the area under the load plate holder with a solid object This could damage the weighing cell Other cleaning information Use damp cloths Do not use any acids alkalis or strong solvents Do not clean using a high pressure cleaning unit or under running water If very dirty remove the weighing pan protective cover Cif present and adjustable feet and clean these items separately Follow all the relevant instructions regarding cleaning intervals and permissible cleaning agents Ranger RD Settings in the menu 3 Settings in the menu 3 1 Operator menu Supervisor menu Note Settings can be changed and functions can be activated in the menu This enables adaptation to individual weighing requirements The menu consists of 6 main blocks containing various submenus on several levels Operating the menu Calling up the menu and entering the password The menu differentiates between 2 operating levels Operator and Supervisor The Supervisor level can be protected by a password When the device is delivered both levels are accessible without a password 1 Press MENU and keep it pressed until COdE appears 2 Press MENU again The menu item tErMINL appears Only the submenu dEVICE is accessible 1 Press MENU and keep it pressed until COdE appears 2 Enter the password and confirm with Yes The first menu item SCALE appears No supervisor password has been defin
38. vironment The scale operates at medium speed HIGH e Restless environment The scale works more slowly but is insensitive to external influences PrOCESS Adaptation to the weighing process UNIVEr e Universal setting for all weighing samples and normal weighing goods dOSING e Dispensing liquid or powdery weighing samples StAbILI Adjusting the weighing speed FASt e The scale operates very fast StAndrd e The scale operates at medium speed PrECISE e The scale operates with the greatest possible reproducibility The slower the scale works the greater the reproducibility of the weighing results 3 3 7 FACT automatic temperature dependent adjustment This menu item appears only on scales with an internal calibration weight TEMP Defining the temperature difference for automatic calibration OFF e Switching off automatic calibration in the case of a temperature difference 1K 2K 3K 5K e Automatic calibration in the case of a temperature change of 1 K 2 K 3 Kor 5 K since the last adjustment 20 Ranger RD Settings in the menu 3 3 8 MIN WEIG minimum weight This menu item appears only if the service technician has saved a minimum weight ON OFF Switching minimum weight function on off If the weight on the scale falls below the stored minimum weight an appears on the display in front of the weight indicator 3 3 9 RESET resetting scale settings to factory settings SUrE Conf
39. warranty is void if this stipulation is ignored The device may only be opened by authorized persons A Call OHAUS Service Ranger RD Introduction AN Note 1 2 CAUTION Handle the compact scale with care The scale is a precision instrument A When the weighing pan has been removed never clean the area under the load plate holder with a solid object A Do not put excessive loads on the scale A Avoid banging the weighing pan Disposal gt Observe the valid environmental regulations when disposing of the scale If the device has a rechargeable battery The battery contains heavy metals and therefore must not be disposed of with normal waste gt Observe the local regulations for disposing of environmentally hazardous materi als Use with foodstuffs Parts coming into contact with foodstuffs have smooth surfaces and are easy to clean The materials used do not splinter and are free of harmful substances With foodstuffs it is recommended to use the supplied protective cover gt Clean the protective cover regularly and carefully gt Replace damaged or very dirty protective cover immediately Description This user manual applies to the following types of compact scales e Ranger RD S with strain gauge weighing cell Protection Class IP43 e Ranger RD S IP with strain gauge weighing cell Protection Class IP65 e Ranger RD M with MonoBloc Protection Class IP43 The compact scales ar
Download Pdf Manuals
Related Search