SDC-15 - Karma Digital
Contents
1. 1080p D ILA 3D Front Projector 2012 Addendum Preface ABOUT THIS MANUAL ADDENDUM This 2012 Manual Addendum is designed for use with the Wolf Cinema SDC 15 Home Cinema Projector This document is intended to accompany and augment the original User s Manual for this product Information in this document has been carefully checked for accuracy however no guarantee is given to the correctness of the contents The information and specifications in this document are subject to change without notice COPYRIGHT Copyright 2012 Wolf Cinema This document contains proprietary information protected by copyright All rights are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer TRADEMARKS All trademarks and registered trademarks are the property of their respective owners The lighting flash with arrow head within an equilateral triangle is intended to alert the user to the presence of dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOIS2. Green Settings 8 8 Blue Settings 8 8 This function adjust for image depth perception Adjust these settings to your preference by using the LEFT RIGHT keys Press the OK key to display the adjustment window The BACK key returns you to the previous screen May be adjusted when the 2D 3D feature is ON Settings 1 5 Select this to automatically identify subtitles and set 3D conversion to On or OFF Adjust settings to your preference May be adjusted when the 2D 3D feature is There may be instances where automatic identification does not work or certain images are identified as subtitles Use the LEFT RIGHT keys to configure your desired settings Press the OK key to display the settings list then use the UP DOWN keys to make your selections The BACK key returns you to the previous screen Settings On Off SDC 15 1080p D ILA 3D Front Projector 2012 Addendum Setting the Screen Size Image Sizing and Aspect Ratio Refer also to page 36 of the SDC 15 User s Manual You can quickly change the screen size aspect ratio of the projected image or mask image borders as desired if the surrounding edges of the image area are distorted Setting the Screen Size Aspect Ratio The projected image can be set to a desired screen size and aspect ratio 1 Select Menu 2 Select Input Signal gt Aspect Video 1 Select 2 Confirm 3 Set aAspect Value 1
3. ORMAT Display the 3D setting menu Use this function to sequentially select focus zoom and shift adjustment lens controls To hide the image temporarily To display close the menu This sequentially switches between users 1 5 To Turn ON the Projector To select input mode This sequentially switches the call up save edit modes of your lens memory PICTURE MODE CINEMA ANIME To adjust color temperature THX USER This sequentially switches anamorphic modes illustrate buttons on the remote control for 7 seconds To select confirm To return to previous menu To switch picture mode Color Profile To set gamma 1 ji COLOR COLOR om ey Sequentially switched picture adjust items such as contrast and brightness The switching items are not the same for different models or different picture modes 3D Format and Settings For additional information about 3D viewing refer to page 54 and pages 59 61 of the SDC 15 User s Manual 3D Format 2D 3D Parallax Crosstalk Cancel Intensity Sub Title Adjust This control selects the 3D input signal format Use the LEFT and RIGHT keys to configure the desired settings Press the OK key to display the available settings list then use the UP DOWN keys to make your selection The BACK key returns you to the previous sc
4. RN Move the cursor to Adjust Pixel then press the OK button to display the pattern and adjustment window Adjust Pixel Window Horizontal Press the OK button to enter the adjustment mode Use the UP DOWN LEFT and RIGHT keys to align the pixels in both the horizontal and vertical directions Select the BACK key to exit this adjustment mode fF Note The operational window and the small remote control indicators when you are in the pixel adjustment mode certain remote control buttons serve as dual use dual function buttons Pixel Adjust Setting Select l Color A ADJUST ColorP COLOR COLOR PIC O GAMMA O TEMP PFILE ADJ Operate O RACI Pixel Alignment and Fine Adjustment Continued REMOTE CONTROL DUAL USE BUTTONS Use the GAMMA button to select ADJUST COLOR i e red or blue pixels Use the COLOR TEMP button to change from the ADJUST PIXEL to the ADJUST FINE operational windows Use the COLOR PILE button to select ADJUST PATTERN COLOR i e white green Use the PIC ADJUST button to change from ADJUST WHOLE AREA to ADJUST ZONE Use the BACK button to stop pixel alignment and exit this mode After making overall large scale window adjustments proceed to fine tuning Press the COLOR TEMP button on the remote to change from ADJUST PIXEL to ADJUST FINE operational windows Or from the main menu set the ADJUST AREA to ALL and sele
5. Select 2 Confirm Lens Control and Lens Memory Lens Control Use this remote button to adjust focus zoom and shift You can also turn the test pattern display ON and OFF and then save your lens position settings during adjustment Use the UP DOWN keys to select an item to adjust Press the BACK key to return to the previous screen Image Pattern Lock Focus This selection adjusts the image focus Zoom This selection adjusts the image overall size Shift This selection enables you to move the image UP DOWN LEFT or RIGHT using the center rosette A test pattern for your use when adjusting focus zoom and shift On During adjustment the test pattern is displayed Off During adjustment the external input signal is displayed without the test pattern This locks out or enables use of the lens controls On This effectively locks out the LENS functions on the remote control Off This enables the LENS functions on the remote control VariScope Lens Memory Select Save Name Edit This menu function and via direct IR remote contro button recalls previously saved lens adjustment memories This is used to toggle between the primary lens VariScope aspect ratio memories i e 1 78 1 1 85 1 2 35 1 and so forth as created by you or your custom installer This saves all focus zoom and shift settings work into one of three available memories the user memories can be renamed Edit and change the
6. TURE DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE DO NOT OPEN THE CABINET REFER SERVICING TO QUALIFIED PERSONNEL ONLY U 7 X Q A 44 lt WARNING To meet FCC requirements a shielded power cord is recommended in order to prevent interference It is essential that only the supplied power cord is to be used Use only shielded cables to connect 1 0 devices to this equipment You are cautioned that changes or modifications not approved by the party responsible for compliance could void your authority to operate the equipment WARNING High brightness light source Do not stare into the beam of light or view directly Be especially careful and ensure that children do not stare directly into the beam of light WARNING To reduce the risk of fire or electric shock do not expose this product to rain or moisture CAUTION For minimal servicing and to maintain high image quality we recommend that you use the projector in an environment that is smoke and dust free When used in areas where there is a lot of smoke or dust the filter and lens should be cleaned often to lengthen the service life of the projector WARNING IC chips or other technologies in the product include confidential and or trade secret property belonging to either Wolf Cinema or the Victor Company of Japan JVC Therefore you may not copy modify adapt translate distribute reverse engineer reverse assemble or decompile the contents thereof WARNING The v
7. b pixels are thus generated based on this process and a true 3840 x 2160 video frame is created Amazingly this process has no moving parts and results in a smooth film like image with minimal visible pixel structure Pixels shifted by Ep E shift elemen changing refraction Resolution doubles horizontally and vertically 1920 1080 To see the benefits of this remarkable V4K light engine you can turn the processor on and off via the following remote control commands Press the OK key then in sequence RIGHT LEFT RIGHT LEFT A small window will appear in the upper right hand corner of the screen indicating the V4K processor is ON Simply depress the RIGHT key to turn the V4K processor to the OFF mode Depress the RIGHT key again to turn it back on Insure that you have the V4K engine turned ON then select the BACK or MENU button to end this demonstration Note This V4K demonstration feature is only possible when watching 2D content Images and technology descriptions courtesy of the Victor Company of Japan JVC 1080p D ILA 3D Front Projector 2012 Addendum Remote Control Your SDC 15 projector remote contro has been modified to incorporate the following features To Turn OFF the Projector This button sequentially switches 3D formats This function cannot be used when inputing 2D and frame packing 3D singles STAND BY 3D F
8. ct ADJUST COLOR and ADJUST PATTERN then move the cursor to ADJUST FINE and press the OK button which will display the pattern and fine tuning operational window Adjust the horizontal vertical pixel structure as required Maximum deviation here is 31 31 Next set the ADJUST AREA to ZONE to make independent zone fine adjustments There will be 11x11 smaller sections that can be independently adjusted For quick access to this menu press the PIC ADJUST button on the remote Use the UP DOWN LEFT and RIGHT keys to move the cursor to the position you want to adjust Press the OK button to enter the operation mode Then use the UP DOWN LEFT and RIGHT keys to move and adjust the pixels within that zone in the horizontal and vertical directions Press the BACK key to return to the previous screen or exit the alignment window Notes on pixel alignment Itis impossible to match all image pixels on the screen Due to properties inherent to D ILA technology there will always be some gaps and overlapping structure Color errors may also result from screen type used and on axis off axis viewing positions In case the image is reversed or upside down the horizontal and vertical directions are reversed Please perform adjustments on a clear still image When fine tuning the effects of adjustments may be limited and perhaps difficult to see on certain image types L 1080p D ILA 3D Front Projec
9. ed without the need for an external anamorphic lens Full anamorphic lens support is also included Advanced multi zone pixel convergence 1 16th pixel 121 zone adjustment e Advanced screen surface compensation driver 255 memories Please review this document to discover the details regarding these important feature enhancements and contact your local Wolf Cinema dealer for further information or contact Wolf Cinema directly at 1 510 843 4500 We hope you enjoy your Wolf Cinema home theater experience Features amp Updates _ amp Updates V4K Enhanced Resolution 3840 x 2180 Wolf Cinema s V4K Technology Originally developed by Japan s NHK Engineering and the Victor Company of Japan JVC and also called e shift in other devices this unique technology implementation by Wolf Cinema delivers an HD image with 4 times the pixel density of standard 1920 x 1080 sources The original 1080p signal is first processed with an advanced imaging algorithm to improve edge transitions eliminate aliasing and stair stepping and increase contrast within each video frame Each frame is then temporally separated into two sub frames at 1920 x 1080 pixels each and projected through the D ILA engine and the V4K processing panel This panel utilizes a property of liquid crystals called bi refringence and can rapidly switch between straight light and refracted light by 0 5 pixel shifted both vertically and horizontally New su
10. ements AC 110V 240V 50 60Hz Power Consumption 350W 3 4A standby mode 0 9W Operation Environment Temperature 5 C to 35 C Humidity 20 to 80 no condensation storage temperature 10 C to 60 C Installation Height Recommended below 5000 ft 1524 m high altitude operating mode available Dimensions WxHxD 19 5 x 8 8 x 22 5 in 496 x 224 x 572 mm Weight 60 Ibs 28 kg net 75 Ibs 34 kg shipping Accessories Please see page 14 of the full User s Manual Notes 2 D ILA is the abbreviation for Direct Drive Image Light Amplifier 3 D ILA devices are manufactured using extremely high precision technology Pixel effectiveness is 99 99 Only 0 01 or less of the pixels may be off or permanently lit and still be within spec 4 HDCP is the abbreviation for High bandwidth Digital Content Protection system 5 Ethernet is not supported e Design and specifications are subject to change without prior notice Please note that some of the pictures and illustrations may have been abridged enlarged or contextualized in order to aid comprehension Images may differ from the actual product 2012 Wolf Cinema Wolf Cinema The New Standard of Excellence Wolf Cinema 2431 Fifth St Berkeley CA 94710 W Tel 510 843 4500 Fax 510 843 7120 www wolfcinema com C I N EM A
11. entilation slots and objects next to them may get extremely hot during operation Do not touch these areas until they have sufficiently cooled down DISPOSAL Do not use household or municipal waste collection services for disposal of electrical and electronic equipment EU countries require the use of separate recycling collection services CAUTION Review all important safeguards operating and installation instructions as provided the accompanying WOLF CINEMA USER S GUIDE prior to using this product SDC 1 5 1080p D ILA 3D Front Projector 2012 Addendum 2012 New Features _ New Features Thank you for purchasing the Wolf Cinema SDC 15 a next generation stereoscopic 3D home cinema projector Starting in January 2012 the SDC 15 projector will incorporate the following new features and upgrades which are described in further detail in this User s Manual Addendum e V4K technology a unique 4K imaging process that converts standard HD sources into 3840 2160 on screen resolution e 2D gt 3D adaptive imaging new video processing algorithms that can render in real time 3D imaging from 2D sources e Adjustable 3D parallax and crosstalk cancellation provides for improved stereoscopic 3D imaging reduced ghosting artifacts and results in more natural 3D image e VariScope lens memories three primary optics presets so that 1 78 1 1 85 1 and 2 35 1 aspect ratios can be instantly recall
12. er memory name you wish to edit Press the OK button on the main unit or the remote control to confirm and enter the edit mode Press the BACK key on the main unit or remote control at anytime to exit the edit mode Doing this will delete your modifications Input Cursor This highlights the edit area The cursor will move automatically as you enter characters Select Cursor Select and move the cursor using the UP DOWN LEFT and RIGHT keys on the projector or on the remote control Select the letter to enter and press the OK button Make the next letter number or symbol selection and press OK Clear Use this to delete a character Move the select cursor to the desired location and press the OK button This will delete the character in the Name field All Clear Use this to delete ALL characters Move the select cursor to the desired location and press the OK button A delete confirmation message will appear OK Use this function to save the entered name information Select OK and a saved confirmation message will appear Pixel Alignment and Fine Adjustment Use this section to adjust fine tune any slight errors in the horizontal vertical pixel alignment It is found under the INSTALLATION menu tab Adjust Adjust Area Adjust Color Adjust Pattern Color Adjust Pixel Adjust Fine Reset Select this function to turn the pixel alignment function ON and OFF Settings Off On Use this functi
13. lens memory aspect ratio names Number of characters is limited to 10 and may include capital and lower case letters numbers and symbols Memory 1 2 or 3 Select the user memory name you wish to edit Input Cursor Select Cursor Press the OK button on the main unit or the remote control to confirm and enter the edit mode A is displayed if the information is not saved Press the BACK key on the main unit or remote control at anytime to exit the edit mode Doing this will delete your modifications This highlights the edit area The cursor will move automatically as you enter characters Move the cursor using the UP DOWN LEFT and RIGHT keys on the projector or on the remote control Select the letter to enter and press the OK button Make the next letter number or symbol selection and press OK 2 5 r o Select Cursor Input Cursor ABE EASA OOK 2 8151 AM JAA OES Character List Hangaia e JAWAD Oo SPACE _Clear_ All Clea OK Exit Operate Back MENU select D BACK 1080p D ILA 3D Front Projector 2012 Addendum Clear Use this to delete a character Move the select cursor to the de
14. on to set the overall pixel adjustment range Settings Whole Zone Whole Selects the entire screen as the adjustment area Zone screen is divided into 11 x 11 sections for fine adjustment Note the size of the individual zones cannot be changed This function selects the color of the pixels you want to adjust Settings Red Blue This function sets the pattern color Settings White Green Adjust Color White Sets the adjustment pattern to white Green Sets the pattern to green and the color set using the Adjust Color items Adjust Color Use this to move the color selected previously Adjust Color pixel by pixel in the vertical and horizontal directions This function is disabled with the Adjust Area is set to Zone H Horizontal Settings 2 2 V Vertical Settings 2 2 Use this to move the color selected previously Adjust Color pixel by pixel in the vertical and horizontal directions H Horizontal Settings 31 31 V Vertical Settings 31 31 Returns all settings to the original default factory settings 1080p D ILA 3D Front Projector 2012 Addendum Pixel Alignment and Fine Adjustment Continued The following steps are useful when re aligning the projector s visible pixel structure Enter the PIXEL ADJUST menu off the INSTALLATION tab First set the ADJUST AREA to WHOLE and make your initial general wholesale adjustments to the image alignment Select ADJUST COLOR and ADJUST PATTE
15. reen Some signals may not be embedded with 3D information thus the image projected may revert to 2D Reconfigure such selections manually It is recommended to read On 3D reference pages 59 61 of the User s Manual before watching 3D video images Settings Auto Side by Side Top amp Bottom 2D Auto 3D formats are determined automatically Side by Side Select this if the 3D input signal is the side by side method Top and Bottom Select this if the 3D signal is the top and bottom method 2D Projected as a 2D signal This feature converts current 2D images into a quasi 3D video image This effect may not be visible with certain content On Select to convert 2D video images to 3D Off Select to NOT convert 2D images into 3D This function enables fine adjustment of any misalignment of the left and right 3D video images Adjust these settings to your preference by using the LEFT RIGHT keys Press the OK key to display the adjustment window The BACK key returns you to the previous screen Cannot be adjusted when the 2D 3D feature is ON Settings 15 15 This reduces cross talk within 3D image content Adjust these settings to your preference by using the LEFT RIGHT keys Press the OK key to display the adjustment window The BACK key returns you to the previous screen May be adjusted during 3D playback but not when the 2D 3D feature is White Settings 8 8 Red Settings 8 8
16. sired location and press the OK button This will delete the character in the Name field All Clear Use this to delete ALL characters Move the select cursor to the desired location and press the OK button A delete confirmation message will appear OK Use this function to save the entered name information Select OK and a saved confirmation message will appear Picture Modes and User Name Edit Picture Modes Refer also to page 47 of the SDC 15 User s Manual Note The major change from last year s remote control is that the USER 1 and USER 2 direct access buttons are now combinedinto the one USER button which toggles through the FIVE available user setting memories User 1 WOLF FACTORY CALIBRATIONS User 2 User 3 User 4 and User 5 Adjust and save your image quality as desired Last adjustments are saved automatically You may change the user names anytime using the USER NAME EDIT feature User Name Edit You can rename any Picture Mode memory bank as below The total number of characters is limited to 10 and may include capital and lower case letters numbers and symbols 1 Picture Adjust gt i Input Cursor Character List Select Cursor gt All Clear OK Exit Operate Back MENU select D BACK User 1 5 Select the us
17. tor 2012 Addendum Remote Control Code Hexadecimal code is sent during communication Remote Control Button Name Hexadecimal Code Remote Control Button Name Hexadecimal Code A 37 3330 31 NATURAL 37 33 36 41 v 37 3330 32 USER 37 33 44 37 BACK 37 3330 33 37 3336 46 ON 37 3330 35 HDMI 1 37 3337 30 STAND BY 37 3330 36 HDMI 2 37 3337 31 HIDE 37 3331 44 PIC ADJ 37 3337 32 LENS AP 37 33 32 30 INFO 37 3337 34 MENU 37 3332 45 GAMMA 37 3337 35 OK 37 3332 46 C TEMP 37 3337 36 LENS CONTROL 37 3333 30 3D 37 33 38 37 gt 37 3333 34 COLOR PROFILE 37 3338 38 4 37 3333 36 C M D 37 33 38 41 PC 37 33 34 36 ANAMO 37 3343 35 37 3334 44 COLOR SPACE 37 3343 44 37 33 36 36 LENS MEMORY 37 33 44 34 37 3336 37 3D SETTING 37 33 44 35 CINEMA 37 33 36 38 3D FORMAT 37 33 44 46 FILM 37 3336 39 2012 Specifications Specifications Product Name Model Name Display Panel Size Projection Lens VariScope Light source Lamp Average Lifespan Screen Size Performance Resolution V4K Resolution 2D gt 3D Algorithm Projection Distance Analog Video Input Format Digital Video Input Format Input terminals Video Input HDMI Input PC Input Output Terminal Trigger terminal 3D Synchro Control Terminal Remote Terminal LAN Terminal Wolf Cinema SDC 15 3D D ILA Home Cinema Projector SDC 15 D ILA device 2 3 0 7 1920 pi
18. xels x 1080 pixels x 3 total no of pixels approx 6 22 million 2 0 x power zoom lens 1 45 1 to 2 78 1 zoom focus power Three user adjustable lens presets 1 78 1 1 85 1 and 2 35 1 aspect ratios NOTE projector throw distance when utilizing the internal VariScope feature is appx 1 45 1 to 2 1 1 x SW external VariScope FX anamorphic lens support also provided 220 W Ultra high pressure mercury lamp Part No WC LPU220 2000 3000 hours normal mode Approx 60 to 200 aspect ratio 16 9 1300 ANSI 100 000 1 CR performance 1920 dots x 1080 dots 3840 dots x 2160 dots Real time conversion of standard 2D images into 3D Approx 1 8m to 12m 480i 480p 576i 576 720p 50 Hz 720p 60 Hz 10801 50 Hz 10801 60 Hz 480i 480p 576i 576p 720p 50 Hz 720p 60 Hz 10801 50 Hz 10801 60 Hz 1080p 24 Hz 1080p 50 Hz 1080p 60 Hz PC compatible signals Reference page 26 1 system RCA pin jack x3 Y 1 0Vp p 75Q Pb Cb Pr Cr 0 7Vp p 750 Also supports R G B Sync G 2 system HDMI 19 pin x 2 HDCP compliant 4 Compatible with the HDMI v1 4a standard 5 1 system D Sub 15 pin VGA 1 system 3 5mm DC power jack DC OUT 12V 0 1A 3D synchro emitter dedicated terminal 1 system mini DIN 3pin RS 232C terminal 1 system D sub 9 pin male x1 external control 1 system stereo mini jack x1 remote control 1 system RJ 45 plug x1 1080p D ILA 3D Front Projector 2012 Addendum Power Requir
Download Pdf Manuals
Related Search