CIRCA Scientific Temperature Monitor User Manual
Contents
1. Set Up Temperature C Audio Tone Volume Test Update Warning Graph Minimum Graph Maximum Figure 8 Set Up Screen a Settings touch button to increase value touch to decrease value Note warning temperature cannot be set equal to or greater than alarm temperature Graph maximum and minimum cannot be set below alarm and warning levels CS ART2005 Rev 03 Page 10 of 27 CIRCA Scientific Temperature Monitor User Manual b Alarm and Warning Audible Levels touch ALARM or WARNING button to hear and update audible tone and volume settings Note warning volume cannot be set equal to or greater than alarm volume Touch bar graph level to desired setting and then UPDATE button to save and exit Tone Yolume Control Graphs Set Up Tone Volume Audio f y i 10 Tone Yolume Test Update il Aarm 9 8 7 6 5 4 3 2 1 9 8 6 5 4 3 2 1 Figure 9 Tone and Volume Setting Note all user selected values are retained the last settings used before shut down will be those recalled upon start up O2 Once set up is complete select desired screen either Maximum Temperature or Channel Graphs in which to view temperatures measured by the temperature probe 03 Disconnect probe from interconnect cable by grasping connectors Do not pull on cable or probe wire to disconnect Note after disc2. you can safely turn off power Select OK Button CS ART2005 Rev 03 Page 13 of 27 CIRCA Scientific Temperature Monitor User Manual 9 Cleaning and Disinfection Disconnect from power before cleaning Use a damp cloth Do not use liquid or spray detergents for cleaning Wipe outer surfaces with damp cloth and let dry Do not rinse soak wash or sterilize If disinfection is required apply non abrasive non corrosive disinfection fluid to disposable cloth wipe outer surfaces and then let dry 10 Maintenance Routine Visual Inspection Visually inspect the monitor and all accessories at least once before each use Inspect the power cord cables and monitor for damage wear and loose components Particular attention should be made to the power cord and interconnect cable for insulation damage such as cuts brittleness cracking and bare spots Do not use if equipment appears damaged Annual Safety Inspection and Accuracy Test The following safety inspection and accuracy test should be performed by hospital s equipment service department at least every 12 months LJ Inspect the equipment and accessories for mechanical damage LJ Inspect all labels and markings for legibility LJ Check temperature accuracy with the following test Equipment 10K Resistor Test Part available from CIRCA Scientific 1 Connect Test Part to Interconnect Cable 2 Turn unit on 3 Observe temperature readings 12 displayed on th
3. 27 CIRCA Scientific Temperature Monitor User Manual 15 15 Symbols Key Equipment Markings Key Equipment Markings Alternating current Dangerous voltage Direct current Caution EU Only Products affected by ON OFF push push the directive Waste of Electrical and Electronic NOTE Each position Equipment WEEE These ON or OFF is a stable products are not to be discarded position nn together with non electrical or non electronic products Centre Positive Indicates that the center tip of the output plug is For indoor use only Positive and the barrel of the output plug is Negative Defibrillation Proof Type BF Applied Part It I fi Oe e ed Date of Manufacture T Manufacturer Caution Federal U S A law restricts this device to sale by or on the order of a Serial Number physician Caution part of defibrillation proof protection is provided by REF the S Cath temperature a E Er probe Do not use with any other applied part Table 4 Symbols Key CS ART2005 Rev 03 Page 21 of 27 CIRCA Scientific Temperature Monitor User Manual 16 Electromagnetic Compatibility Warning Use of cables and accessories other than those supplied and sold by CIRCA Scientific may result in increased emissions or decreased immunity of the equipment Warning The equipment should not be used adjacent to or stacked with other equipment If adjacent or stack
4. CIRCA Scientific Temperature Monitor User Manual CIRCA Scientific Temperature Monitoring System Model CS 1000 CIRCA YV SCIENTIFIC CIRCA Scientific LLC 14 Inverness Drive East Suite H240 Englewood CO 80112 303 951 8767 CS ART2005 Rev 03 Page 1 of 27 CIRCA Scientific Temperature Monitor User Manual Table of contents 1 General warnings and cautions Page 3 2 Indications for use Page 4 3 Description Page 4 4 Alarm System Overview Page 7 5 Setup instructions Page 8 6 Check out instructions Page 9 7 Operating instructions Page 10 8 Shut Down Page 12 9 Cleaning and Disinfection Page 14 10 Maintenance Page 14 11 Storage and Transportation Page 15 12 Troubleshooting Page 16 13 Accessories Page 18 14 Technical Information Page 19 15 Symbols Key Page 21 16 Electromagnetic Compatibility Page 22 CS ART2005 Rev 03 Page 2 of 27 CIRCA Scientific Temperature Monitor User Manual 1 General warnings and cautions Rx Only Federal U S A law restricts this device to sale by or on the order of a physician The monitor is designed for use with CIRCA Scientific interconnect cables and temperature probes only Incompatible components can result in degraded performance and could lead to damage to the unit No modification of this equipment is allowed Never pour any liquid into an opening This may cause fire or electrica
5. Overview CS ART2005 Rev 03 Page 17 of 27 CIRCA Scientific Temperature Monitor User Manual 13 Accessories The monitor is designed for use with CIRCA Scientific interconnect cables and temperature probe only The interconnect cables and temperature probes are sold separately Contact CIRCA Scientific or Authorized Distributor for ordering information The Recorder Port located on the back of the monitor is intended to connect with the 0 to 5V analog input of a recording device that is compliant with IEC 60601 1 Do not connect this port to any other device Caution Use of accessories or replacement parts not supplied by CIRCA Scientific can result in degraded performance and could lead to damage to the unit Warning Use of cables and accessories other than those supplied by CIRCA Scientific may result in increased emissions or decreased immunity of the equipment Power Supply use only Sinpro model MPU50 105 power supply N Recorder Port Monitor Front View Interconnect Cable Temperature Probe Sold Separately Sold Separately Figure 10 Equipment Illustration CS ART2005 Rev 03 Page 18 of 27 CIRCA Scientific Temperature Monitor User Manual 14 Technical Information Classification Class I Defibrillation Proof Type BF Applied Part Continuous Operation Electrical Mains Mains Supply Voltage 100 240V AC Mains Supply Frequency 47 63 Hz Mains R
6. System The CIRCA Scientific CS 1000 Temperature Monitoring System is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled The customer or the user of the CIRCA Scientific CS 1000 Temperature Monitoring System can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and the CIRCA Scientific CS 1000 Temperature Monitoring System as recommended below according to the maximum output power of the communications equipment Rated maximum Separation distance according to frequency of transmitter output power of transmitter 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2 5 GHz d 1 2 VP d 1 2 VP d 2 3 VP 0 12 meters 0 12 meters 0 23 meters 4 7 inches 4 7 inches 9 1 inches 0 38 meters 0 38 meters 0 73 meters 15 0 inches 15 0 inches 28 7 inches 1 2 meters 3 9 feet 3 8 meters 12 5 feet 12 meters 39 4 feet 1 2 meters 3 9 feet 3 8 meters 12 5 feet 12 meters 39 4 feet 2 3 meters 7 6 feet 7 3 meters 24 0 feet 23 meters 75 5 feet For transmitters rated at a maximum output power not listed above the recommended separation distance d in meters m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts W according to the transm
7. ated Input 1 35A Electrical Power Output Voltage 12V DC Max Supply Current 3 75A Max Use only Sinpro model MPU50 105 power supply Electrical Monitor Input Voltage 12 19 V DC Power Input Current 3 75 2 63A Electrical Safety and Meets IEC 60601 1 1988 A1 1991 A2 1995 Electromagnetic Meets IEC 60601 1 2 2007 Compatibility User Settings Alarm and Warning Temperature Levels in 0 1 C increments Alarm and Warning Tone and Volume 1 10 in single digit increments Graph y axis Minimum and Maximum in 1 C increments Setting range O C to 90 C Measurement Display Update rate 50 milliseconds Graph time span 60 seconds Accuracy 0 3 C Precision 0 1 C Alarm System Intended position of the Operator to observe the Alarm Signal is within an approximate distance of 4 5 feet 1 4 meters Alarm Signal Sound Pressure Range 45 to 85 dB CS ART2005 Rev 03 Page 19 of 27 CIRCA Scientific Temperature Monitor User Manual Physical Dimensions monitor 10 2 W x 7 8 H x 3 25 D 258 W x 199 H x 83 D mm Weight 5 5 Ibs 2 6 kg Disposal No special precautions are required Dispose of equipment per hospital policy EU Only Products affected by the directive Waste of Electrical and Electronic Equipment WEEE These products are not to be discarded together with non electrical or non electronic products Table 3 Technical Information CS ART2005 Rev 03 Page 20 of
8. ce or damage to other property Warning is a statement that alerts the user to the possibility of injury death or other serious adverse reactions associated with the use or misuse of the device CS ART2005 Rev 03 Page 3 of 27 CIRCA Scientific Temperature Monitor User Manual 2 Indications for use Display continuous temperature measurement C from 12 sensor temperature probe 3 Description The CIRCA Scientific Temperature Monitoring System consists of a touch screen monitor bracket and power supply The monitor is to be used with CIRCA Scientific interconnect cable and temperature probe only The interconnect cable and temperature probe are sold separately Touch Screen Monitor XN _ Power Button Power Supply S Monitor Front View Monitor Back View Interconnect Cable Temperature Probe Sold Separately Sold Separately Figure 1 System Equipment CS ART2005 Rev 03 Page 4 of 27 CIRCA Scientific Temperature Monitor User Manual The monitor displays 12 temperature probe sensor readings C the maximum temperature of all sensors and contains an alarm system with user selected levels The monitor features the following three screens Maximum 12 Channel Temperature Monitor Temperature Maximum Temperature Channel Graphs Set Up Monitoring ra 37 0 E 37 0 B g 27 0 M370 g 37 0 E 37 0 d 7 0 37 0 g 37 0 Bf 37 0 g 37 0 Mf 37 0 Audio Off Chan
9. e Turn monitor back on by momentarily pushing Power Button on back of monitor Probe Disconnected Ensure temperature probe is firmly seated to interconnect cable and interconnect cable 1s No valid temperature data firmly seated to monitor Please check probe When properly connected message will terminate and temperature readings display Touch OK button Ensure USB Cable back of monitor is firmly seated in ports Reconnect cable Proceed with Shut Down from Windows screen Seral Port and or Thermal Array Monitor Failed to mtialze The poart COM16 does not exist Turn monitor back on by momentarily pushing Power Button on back of monitor Table 1 Message Overview C4 Proceed with operating instructions below CS ART2005 Rev 03 Page 9 of 27 CIRCA Scientific Temperature Monitor User Manual 7 Operating instructions Screen navigation and set up is by touch screen Different screens may be selected by touching the tab near the top of the screen Maximum Temperature Channel Graphs Touch Tab to Select Maximum Temperature Channel Graphs Maximum Temperature Channel Graphs Set Up Maximum Temperature Channel Graphs Set Up Temperature C Audio Tone Volume Test Update Alarm ae Alarm wring EE Warning Graph Graph Figure 7 Display Screens O1 Select Set Up tab to set desired alarm system levels and graph y axis minimum and maximum Maximum Temperature Channel Graphs
10. e monitor 4 Calculate the measurement error for each individual Output Temperature measurement by subtracting reading from 25 0 C 5 Ensure that the measurement error is not greater than 0 3 C Do not use equipment if the inspections or test reveal a defect The equipment has no serviceable parts Warning to prevent shock do not remove cover Refer servicing to qualified personnel CS ART2005 Rev 03 Page 14 of 27 CIRCA Scientific Temperature Monitor User Manual 11 Storage amp Transport Do not leave this equipment in an environment where the storage temperature may go below 20 C 4 F or above 60 C 140 F This could damage the equipment If shipping equipment pack in original carton and packing materials If original packing material is not available cover monitor pack with foam and ship in sturdy box to prevent damage during transport CS ART2005 Rev 03 Page 15 of 27 CIRCA Scientific Temperature Monitor User Manual 12 Troubleshooting Message USE Communications Failure USB Communications Failure Please reconnect USB cable and restart system Message Probe Disconnected No valid temperature data Please check probe Message Seral Port and or Thermal Array Monitor faled to initialize The port COMT6 does not exist Monitor does not boot up and BIOS Configuration reset to default CS ART2005 Rev 03 Touch OK button Ensure USB Cable back of monitor is
11. ed use is necessary the monitor should be observed to verify normal operation Normal operation is considered as absence of unusual erratic variations in temperature readings The equipment may be affected by portable and mobile RF Radio Frequency communications equipment Table 5 Guidance and manufacturer s declaration Electromagnetic Emissions The CIRCA Scientific CS 1000 Temperature Monitoring System is intended for use in the electromagnetic environment specified below The customer or the user of the CIRCA Scientific CS 1000 Temperature Monitoring System should assure that it is used in such an environment Emissions test Compliance Electromagnetic environment guidance RF emissions Group The CIRCA Scientific CS 1000 Temperature CISPR 1 Monitoring System uses RF energy only for its internal function Therefore its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment RF emissions Class A shag The CIRCA Scientific CS 1000 Temperature Harmonic emissions Class A Monitoring System is suitable for use in all establishments other than domestic and those IEC 61000 3 2 directly connected to the public low voltage Veloce acao Conpites power supply network that supplies buildings i ee used for domestic purposes flicker emissions IEC 61000 3 3 CS ART2005 Rev 03 Page 22 of 27 CIRCA Scientific Temperature Monitor User Manual Table 6 Guidance a
12. ee Operating Instructions section below for setting instructions WARNING is a lower priority than ALARM WARNING 1s identified by YELLOW ALARM 1s identified by RED AUDIO OFF inactivates the audible signal only until another event occurs Another event includes maximum temperature increasing from warning to alarm level or temperature drops below warning or alarm value then increases and is equal and above set value 12 Channel i Channel Graphs Set Up Temperature Monitor 12 12 Channel i Channel Graphs Set Up Temperature Monitor Figure 5 Alarm Signal CS ART2005 Rev 03 Page 7 of 27 CIRCA Scientific Temperature Monitor User Manual 5 Setup instructions The operator is responsible for checking the compatibility of the monitor interconnect cable and temperature probe before use Ensure only CIRCA Scientific components and equipment is connected S1 Mount monitor to standard IV pole or similar rigid structure Secure by tightening knob located at the bottom of the bracket S2 Adjust monitor to desired position tilt position and angle using lock levers located on bracket Note intended position of the Operator to observe the Alarm Signal is within an approximate distance of 4 5 feet 1 4 meters S3 Connect interconnect cable to monitor connection located on back of monitor by aligning snap fit connectors and pushing firmly S4 Connect temperature probe to interconnect cable by aligning sna
13. ent level guidance Portable and mobile RF communications equipment should be used no closer to any part of the CIRCA Scientific CS 1000 Temperature Monitoring System including cables than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter Recommended separation distance 3 Vrms 3 Vrms d 1 2VP 150 kHz to 80 MHz Conducted RF IEC 61000 4 6 3 V m 3 V m d 1 2 VP 80 MHz to 2 5 GHz 80 to 800 MHz Radiated RF IEC 61000 4 3 d 2 3 yP 800 MHz to 2 5 GHz Where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in meters m Field strengths from fixed RF CS ART2005 Rev 03 Page 25 of 27 CIRCA Scientific Temperature Monitor User Manual transmitters as determined by an electromagnetic site a survey should be less than the compliance level in each f b requency range Interference may occur in the vicinity of equipment that include RF transmitters or that apply RF electromagnetic energy for diagnosis 1 e equipment marked with the following symbol H Note 1 At 80 MHz and 800 MHz the higher frequency range applies Note 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people a Field strengths from fixed transmitters s
14. firmly seated in ports Reconnect cable Proceed with Shut Down from Windows screen Turn monitor back on by momentarily pushing Power Button on back of monitor Ensure temperature probe is firmly seated to interconnect cable and interconnect cable is firmly seated to monitor Replace probe and or interconnect cable if no temperature data can be displayed after verifying connections Touch OK button Ensure USB Cable back of monitor is firmly seated in ports Reconnect cable Proceed with Shut Down from Windows screen Turn monitor back on by momentarily pushing Power Button on back of monitor The computer inside the monitor is provided with a battery powered real time clock circuit The battery has no power Warning There is a danger of explosion if battery is incorrectly replaced Refer servicing to qualified personnel Page 16 of 27 CIRCA Scientific Temperature Monitor User Manual S is displayed for an individual sensor No action required temperature reading and an individual sensor graph under Channel Graphs display is orange The four dashes and orange colored graph indicate an individual sensor wire has failed Frozen Screen Monitoring indicator does not flash Shut down unit and re start 12 Channel Temperature Monitor Monitoring 12 0 i 11 A 37 0 E 27 0 E J 270 E 370 E d 27 0 E 270 E g 270 E 370 E J 370 E 370 E Table 2 Troubleshooting
15. itter manufacturer Note 1 At 80 MHz and 800 MHz the separation distance for the higher frequency range applies Note 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people CS ART2005 Rev 03 Page 27 of 27
16. ive humidity should be at least 30 Mains power quality should be that of a typical commercial or hospital environment Mains power quality should be that of a typical commercial or hospital environment Mains power quality should be that of a typical commercial or hospital environment If the user of the CIRCA Scientific CS 1000 Temperature Monitoring System requires continued operation during power mains interruptions it is recommended that the CIRCA Scientific CS 1000 Temperature Monitoring System be powered from an uninterruptible power supply or a battery Page 23 of 27 CIRCA Scientific Temperature Monitor User Manual Power frequency Power frequency magnetic 50 60 Hz magnetic fields should be at levels field characteristic of a typical location in a typical commercial or hospital environment IEC 61000 4 8 Note Uris the a c mains voltage prior to application of the test level CS ART2005 Rev 03 Page 24 of 27 CIRCA Scientific Temperature Monitor User Manual Table 7 Guidance and manufacturer s declaration Electromagnetic Immunity The CIRCA Scientific CS 1000 Temperature Monitoring System is intended for use in the electromagnetic environment specified below The customer or the user of the CIRCA Scientific CS 1000 Temperature Monitoring System should assure that it is used in such an environment Immunity test IEC 60601 test level Compliance Electromagnetic environm
17. l shock Do not cover the openings Overheating may occur as the openings on the enclosure are for air convection If the equipment is not in use disconnect it from the power source to avoid damage by transient overvoltage Do not remove cover No user serviceable parts inside There is a danger of shock if incorrectly serviced There is a danger of explosion if battery is incorrectly replaced Refer servicing to qualified personnel To avoid the risk of electric shock this equipment must only be connected to a supply mains with protective earth To avoid product damage do not repair or replace power supply and USB Cable Refer servicing to qualified personnel This equipment needs special precautions regarding EMC Electromagnetic Compatibility and needs to be put into service according to the EMC information provided in section 16 Electromagnetic Compatibility Do not connect additional accessory equipment to the analog and digital interfaces for signal input or output Personnel who connect additional equipment configure a medical system degraded performance and damage to the unit could occur Part of defibrillation proof protection is provided by the S Cath temperature probe Do not use with any other applied part Caution is a statement that alerts the user to the possibility of a problem with the device associated with its use or misuse Such problems include device malfunction device failure damage to the devi
18. nd manufacturer s declaration Electromagnetic Immunity The CIRCA Scientific CS 1000 Temperature Monitoring System is intended for use in the electromagnetic environment specified below The customer or the user of the CIRCA Scientific CS 1000 Temperature Monitoring System should assure that it is used in such an environment Immunity test IEC 60601 test level Compliance level Electromagnetic environment guidance Electrostatic discharge ESD IEC 61000 4 2 Electrical fast transient burst IEC 61000 4 4 Surge IEC 61000 4 5 Voltage dips short interruptions and voltage variations on power supply input lines IEC 61000 4 11 CS ART2005 Rev 03 6 kV contact 8 kV air 2 kV for power supply lines 1 kV for input output lines 1 kV line s to line s 2 kV line s to earth lt 5 Ur gt 95 dip in Ur for 0 5 cycle 40 Ur 60 dip in Ur for 5 cycles 70 Ur 30 dip in Ur for 25 cycles lt 5 Ur gt 95 dip in Ur for 5 s 6 kV contact 8 kV air 2 kV for power supply lines kV for input output lines 1 kV line s to line s 2 kV line s to earth lt 5 Ur gt 95 dip in Ur for 0 5 cycle 40 Ur 60 dip in Ur for 5 cycles 70 Ur 30 dip in Ur for 25 cycles lt 5 Ur gt 95 dip in Ur for 5 s Floors should be wood concrete or ceramic tile If floors are covered with synthetic material the relat
19. nel 12 Channel Graphs Temperature Monitor Monitoring re 27 0 E 7 0 B A 37 0 7 d 270 E 37 0 E 37 0 3 g 37 0 E 37 0 amp Maximum Temperature Channel Graphs Set Up Audio Off 12 Channel Maximum Temperature Channel Graphs J SetUp Temperature Monitor Monitoring fli 37 0 Mf 37 0 BE 12 7370 EZA 1A Alarm 7370 E ai 5 4 1 Temperature C Audio Tone Volume Test Update Waring 37 0 37 0 Graph Graph Minimum Audio Off Figure 2 Display Screens CS ART2005 Rev 03 Page 5 of 27 CIRCA Scientific Temperature Monitor User Manual Note numbered channels 1 through 12 correspond to each sensor located within the S Curve of the temperature probe Channel number begins with sensor 1 located on distal end l 7 I N l Soiree 2 Pan 12 Figure 3 Temperature Probe Sensor Location CS ART2005 Rev 03 Page 6 of 27 CIRCA Scientific Temperature Monitor User Manual 4 Alarm System Overview The alarm system provides visual and audible feedback when a sensor temperature is equal to and above the user selected value The alarm system is intended to provide operator feedback regarding temperature compared to user selected levels only it does not provide physiological alarm conditions The visual and audible signal is triggered when a sensor temperature is equal to and above the set value Alarm levels are set by the operator s
20. onnecting the message No valid temperature data Please check probe will display O4 Prepare temperature probe for patient use per temperature probe s instructions for use O5 Once temperature probe is set in patient and connected to interconnect cable temperatures will display CS ART2005 Rev 03 Page 11 of 27 CIRCA Scientific Temperature Monitor User Manual 8 Shut Down Turn monitor off by following 3 steps Step 1 Go to Set Up Screen and select Stop Button Maximum Temperature Channel Graphs Set Up Temperature C Audio Tone Volume Test Update a 2 e BEES Select Stop Button Graph Graph After Selecting Stop Program will exit to Windows Screen Step 2 Select Start Shutdown Windows Embedded Standard o My Documents fe My Recent Documents gt bS My Computer My Network Places E Control Panel amp Network Connections s etwork Co gt Printers and Faxes 9 Help and Support Search Run Select Start Button Select Shut Down Button CS ART2005 Rev 03 Page 12 of 27 CIRCA Scientific Temperature Monitor User Manual Step 3 Select OK and unit will shut down _ Windows Embedded Standard Shut Down Windows Copyrigh 1985 2008 Microsoft Corporation LT What do you want the computer to do Shut down Ends your session and shuts down Windows so that
21. p fit connectors and pushing firmly S5 Plug power cord into power outlet Warning To avoid the risk of electric shock this equipment must only be connected to a supply mains with protective earth W NNA Uf N Hi W Wi Wii i Cable to Monitor I i I connection WA ji pea n Hi lf a AN VA 7 iN Wij _ Qa A Lec SS ee j e i LSS C i E j W Cable to Temperature Probe l l l l l l l l l l M connection Qj Power Supply Se 100 240 AC Figure 6 Setup Connections CS ART2005 Rev 03 Page 8 of 27 CIRCA Scientific Temperature Monitor User Manual 6 Check out Instructions C1 Turn monitor on by momentarily pushing Power Button located on back of monitor C2 During start up monitor will deliver a test audible alarm signal 3 beeps If no audible signal is heard sound system is defective Refer service of monitor to qualified personnel C3 Verify temperatures are displayed on monitor If no temperature displays verify connections are fully seated and resolve any error messages displayed on monitor The following messages will display if cables are not connected or unit does not initialize USE Communications Failure Touch OR button Ensure USB Cable back of monitor 1s firmly USB Communications Failure seated in ports Reconnect cable Please reconnect USB cable Proceed with Shut Down from Windows and restart system screen
22. uch as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the CIRCA Scientific CS 1000 Temperature Monitoring System is used exceeds the applicable RF compliance level above the CIRCA Scientific CS 1000 Temperature Monitoring System should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as re orienting or relocating the CIRCA Scientific CS 1000 Temperature Monitoring System 0 Over the frequency range 150 kHz to 80 MHz field strengths should be less than 3 V m Note If high frequency surgical equipment is used at the same time and interferes with the operation of the CIRCA Scientific CS 1000 Temperature Monitoring System additional measures may be necessary such as re orientation of cables relocation and or connecting the hospital grade power cable into a different grounded receptacle or separate grounded power source CS ART2005 Rev 03 Page 26 of 27 CIRCA Scientific Temperature Monitor User Manual Table 8 Recommended separation distances between portable and mobile RF communications equipment and the CIRCA Scientific CS 1000 Temperature Monitoring
Download Pdf Manuals
Related Search