Home

www.nemko.com

Contents

1. ATTACHMENT TO TEST REPORT IEC 60950 1 EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES Information technology equipment Safety Part 1 General requirements Differences according to EN 60950 1 2006 A11 2009 Attachment Form No EU _GD_IEC60950_1A Attachment Originator SGS Fimko Ltd Master Attachment Date 2009 09 Copyright 2009 IEC System for Conformity Testing and Certification of Electrical Equipment IECEE Geneva Switzerland All rights reserved EN 60950 1 2006 A11 2009 CENELEC COMMON MODIFICATIONS IEC 60950 1 GROUP DIFFERENCES CENELEC common modifications EN Contents Add the following annexes P Annex ZA normative Normative references to international publications with their corresponding European publications Annex ZB normative Special national conditions Annex ZC informative A deviations General Delete all the country notes in the reference document according to the following P list 1 4 8 Note 2 1 5 1 Note 2 amp 3 1 5 7 1 Note 1 5 8 Note 2 1 5 9 4 Note 1 7 2 1 Note 4 5 amp 6 2 2 3 Note 2 2 4 Note 23 2 Note 2 3 2 1 Note 2 2 3 4 Note 2 2 6 3 3 Note 2 amp 3 2 7 1 Note 2 10 3 2 Note 2 2 10 5 13 Note 3 2 1 1 Note 3 2 4 Note 3 25 1 Note 2 43 6 Note1 amp 2 4 7 Note 4 4 7 2 2 Note 4 7 3 1Note 2 5 1 7 1 Note3 amp 4 5 3 7 Note 1 6 Note2 amp 5 6 1 2 1 Note 2 6 1 2 2 Note 6 2 2 Note 6 2 2 1 Note 2 6 2 2 2 Note 7 1 Note 3 7 2 Note 7 3 Note1 amp 2 G 2 1 Note 2 Annex H Note
2. NOTE In Sweden switches containing mercury are not permitted Switzerland Ordinance on environmentally No switch containing mercury hazardous substances SR 814 081 Annex 1 7 in the equipment Mercury Annex 1 7 of SR 814 81 applies for mercury Add the following NOTE In Switzerland switches containing mercury such as thermostats relays and level controllers are not allowed ON Nemko Page 12 of 12 Report No 175993 www nemko com IEC60950_1A ATTACHMENT Requirement Test Result Remark Denmark Heavy Current Regulations Class III equipment Supply cords of CLASS EQUIPMENT which is delivered without a plug must be provided with a visible tag with the following text Vigtigt Lederen med gr n gul isolation ma kun tilsluttes en klemme meerket eller If essential for the safety of the equipment the tag must in addition be provided with a diagram which shows the connection of the other conductors or be provided with the following text For tilslutning af de vrige ledere se medf lgende installationsvejledning Germany Gesetz Uber technische Arbeitsmittel Not applicable und Verbraucherprodukte Gerate und Produktsicherheitsgesetz GPSG Law on technical labour equipment and consumer products of 6th January 2004 Section 2 Article 4 Clause 4 Item 2 If for the assurance of safety and health certain rules during use amending or maintenance of a technical labo
3. USB port CN8 0 100 pin 2 4 RTN PL10 s c USB port CN8 7 28 5 60 nu 14 21 100 pin 1 RTN PU10 pin2 8 s c pin 2 4 RTN PU10 pin2 8 S C pin 1 RTN normal pin 2 4 RTN normal USB port CN9 4 96 0 70 ng 1 71 100 pin 1 RTN PL10 s c pin 2 4 RTN PL10 s c pin 1 RTN PU10 pin2 8 s c pin 2 4 RTN PU10 pin2 8 S C USB port CN14 4 96 3 31 ng 9 38 100 pin 1 RTN normal pin 2 4 RTN normal USB port CN14 4 96 0 70 ng 1 60 100 pin 1 RTN PL10 s c TRF No IEC60950_1C N Nemko Page 40 of 46 Report No 175993 www nemko com Uoc Isc A VA pin 2 4 RTN PL10 s c pin 1 RTN PU10 s c pin 2 4 RTN PU10 s c pin 10 RTN pin 1 9 11 13 RTN All pins to RTN All pins to RTN Supplementary information s c short circuit All tests are conducted under U5 by passed condition 2 10 2 Table working voltage measurement ON RMS voltage V Peak volage Supplementary information 2 10 3 and TABLE Clearance and creepage distance measurements 2 10 4 Clearance cl and creepage U peak Ur m s Required cl cl Required cr cr distance cr at of between V V mm mm mm mm Supplementary information 2 10 5 TABLE Distance through insulation measurements Distance through insulation DTI at of U peak U ms V Test volt Required V mm Supplementary information
4. Yes P data is not available Is it possible to install the battery in a reverse polarity position ee N OE Non rechargeable batteries Rechargeable batteries Discharging Un Charging Discharging Reversed intentional charging Meas Manuf SIE Meas Manuf Meas Manuf Meas Manuf current Specs current Specs current Specs current Specs Max 1 current during normal condition Max current during fault condition 1 Battery polarity can t be reversed according to the design of enclosure and connector 2 For RTC battery refer to above table for details Chemical leaks No chemical leaks affecting required insulation Emission of flame or expulsion of molten metal No emission of flame or expulsion of molten metal Electric strength tests of equipment after completion of tests Class III equipment Supplementary information TRF No IEC60950_1C ON Nemko Page 43 of 46 Report No 175993 www nemko com TABLE maximum temperatures P LEen I 1 discharge maximum temperature T of part at T C allowed Tmax C PCB near U19 44 5 42 8 84 5 PCB near U20 43 9 43 0 84 5 RTC body 40 9 39 2 PCB near U17 40 0 39 2 84 5 Enclosure inside near U19 40 0 39 2 Enclosure outside near U19 36 1 35 1 54 5 Battery Pack 30 2 29 9 54 5 Palm rest 25 0 25 9 54 5 Ambient 24 5 24 8 supplementary information Having a specified max
5. 2 3 1 Limits 2 3 1 2 3 5 No TNV circuits Type of TNV circuits pe Separation from other circuits and from accessible RN parts 2321 Teesra H 2322 Jraeaenterrete JH 2323 Protesionbyeathing Oo Protection by other constructions O 233 Separation romhazerdousvotages O Twn Insulation employed O RS 234 Connection of TNV ereus to nea n Insulation employed O O O 235 Testforoperaing volages generated exemaly w TRF No IEC60950_1C N Nemko Page 14 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark Limited current circuits oN General requirements No limited current circuits oN aa Loes Frequency Hz Measured current mA Measured voltage V Measured circuit capacitance nF or UE 2 4 3 Connection of limited current circuits to other circuits Limited power sources p a Inherently limited output MIC headphone ports are inherently limited only for signal transmission SD Card reader slot is inherently limited it can only insert the storage cards and covered by fire enclosure when such cards insert to the ports b Impedance limited output c Regulating network limited output under normal USB ports are limited by operating and single fault condition regulating network refer to appended table 2 5 d Overcurrent protective device limited output Max output voltage V max output current A refer to app
6. No TNV circuits oN Battery compartments No TNV circuits oN Access to ELV wiring Class III equipment oN Working voltage Vpeak or Vrms minimum distance through insulation mm Access to hazardous voltage circuit wiring Class III equipment oN No energy hazard in operator access area Checked by means of the test finger Manual controls No shafts of knobs etc at ELV or hazardous voltage Discharge of capacitors in equipment Class III equipment oN The equipment is not connected to d c mains supply TRF No IEC60950_1C N Nemko Page 13 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark i a Capacitor connected to the d c mains supply Fo nl WW b Internal battery connected to the d c mains oe Audio amplifiers The audio circuit complies with 2 1 1 1 Protection in service access areas Checked by inspection unintentional contact is unlikely during service operations 2 1 3 Protection in restricted access locations Equipment not intended for installation in RAL 2 2 1 General requirements SELV limits are not exceeded under normal condition and after a single fault Voltages under normal conditions V Within SELV limits P Voltages under fault conditions V Within SELV limits P 2 2 4 Connection of SELV circuits to other circuits j SELV circuits are only connected to other SELV circuits ao maen OOS ON
7. Test results according to last modification date 2008 07 31 in CB Bulletin IEC 60950 1 ed 2 Page 2 of 7 www nemko com Report No 175993 IEC 60950 1 2005 Requirement Test Result Remark 2 5 Where a fuse is used to provide Class 2 Limited No such fuse used Power Source or TNV current limiting it shall not be operator accessible unless it is not interchangeable 21 Suitable NEC CEC branch circuit protection rated Class III equipment at the maximum circuit rating is required for all standard supply outlets and receptacles such as supplied in power distribution units if the supply branch circuit protection is not suitable Power distribution transformers distributing power at 100 volts or more and rated 10 kVA or more require special transformer overcurrent protection 3 2 Wiring methods terminals leads etc used for the Class IlI equipment connection of the equipment to the mains shall be in accordance with the NEC CEC 3 2 1 Power supply cords are required to have Class III equipment attachment plugs rated not less than 125 percent of the rated current of the equipment 3 2 1 2 Equipment connected to a centralized d c power Class IlI equipment system and having one pole of the DC mains input terminal connected to the main protective earthing terminal in the equipment is required to comply with special earthing wiring marking and installation instruction requirements 3 2 3 Permanent connection
8. WMT Tested by name signature Witnessed by signature Approved by signature S Testing location address L Testing procedure SMT Tested by name signature Approved by signature Supervised by signature S Testing location address L Testing procedure RMT Tested by name signature Approved by signature d Supervised by signature f Testing location address TRF No IEC60950_1C N Nemko Page 4 of 46 Report No 175993 www nemko com Summary of testing Tests performed name of test and test clause Testing location See page 3 Power interface Marking and instructions Limited power sources Mechanical Strength Design and construction Thermal requirement Openings in enclosures Resistance to fire Abnormal operating and fault conditions Annex A Tests For Resistance To Heat Aand Fire Operation condition The unit is sending receiving data to all I O ports Each USB port loaded to 0 5A Speaker is adjusted to max volume Adjustment of brightness is set to maximum The empty battery pack is charging at the same time Radio and television interference suppression Must be considered when marketing in Norway compliance with the EMC directive is necessary for achieving type certification The appliance shall comply with the relevant EMC standards depending on the
9. symbol to alert user to important operating maintenance and or servicing instructions and the explanation of above symbols Marking is permanent comprehensible and easily discernible on the equipment NAF 2 8 3 Safety interlock can not be activated by articulated accessibility probe NAF 1 NAF 3 4 Isolation switch complying with 3 4 2 is provided to disconnect power to hazardous moving parts On off marking is provided for two position switch Off marking for multi position switch sese eee NAF 4 4 Protection against hazardous moving parts TRF No CSA60950 1 07A bI070423 Test results according to last modification date 2008 07 31 in CB Bulletin IEC 60950 1 ed 2 Page 7 of 7 www nemko com Report No 175993 IEC 60950 1 2005 Requirement Test Result Remark Verdict Accessibility probe Fig NAF 1 is inserted without force into each opening and did not contact hazardous moving parts Operator accessible guards are removed and Accessibility wedge is inserted into each opening according without contacting mechanical hazards e TE ET Cross cut 90N TRF No CSA60950 1 07A bI070423 Test results according to last modification date 2008 07 31 in CB Bulletin IEC 60950 1 ed 2 Page 1 of 8 www nemko com Report No 175993 IEC 60950 1 2005 Requirement Test Result Remark Verdict USA Differences to IEC 60950 1 2005 Second Edition P 1 1 Equipment
10. www nemko com object part No manufacturer type model technical data standard mark s of trademark conformity PCB Hannstar MV 4 V 0 130 C UL 796 UL Board Corp Kunshan ML V 0 130 C UL Yuanmao Various Various V 1 min 105 C UL min Speakers Various Various 8Q 1 0W max Tested in the Two provided equipment Wireless LAN QMI EM113 MV 3 3Vdc Tested in the Card Lite On WN6301MH 3 3Vdc equipment Optional Various Various 3 3Vdc supplementary information an asterisk indicates a mark which assures the agreed level of surveillance TABLE Opto Electronic Devices oN M ANUFACIUIER yaaa vaa x S N See TY P eecssetedi EE a Separately tested sse esse ee esse ereenn neee Bridging insulation sese eee eee ee External creepage distance S Internal creepage distance Distance through insulation ee E Tested under the following conditions ler E ST OOE E T Supplementary information TRF No IEC60950_1C N Nemko Page 38 of 46 Report No 175993 www nemko com 1 6 2 TABLE Electrical data in normal conditions P U V I A trated A p W Ifuse A Condition status DH 20 88 Normal load 1 AD Battery charging only 1 SC Ce oe 2 ave Ces ou 1e gt ef wa ed Cos re 1s w eatery enarna oniy 27 Cos 1m 1s Lasel romana o Cos re 1s w aegegeen Gs pa le System o
11. 2 ON Nemko Page 2 of 12 Report No 175993 www nemko com IEC60950_1A ATTACHMENT Requirement Test Result Remark Add the following subclause 1 3 21 Exposure to excessive sound pressure The apparatus shall be so designed and constructed as to present no danger when used for its intended purpose either in normal operating conditions or under fault conditions particularly providing protection against exposure to excessive sound pressures from headphones or earphones NOTE Z1 A new method of measurement is described in EN 50332 1 Sound system equipment Headphones and earphones associated with portable audio equipment Maximum sound pressure level measurement methodology and limit considerations Part 1 General method for one package equipment and in EN 50332 2 Sound system equipment Headphones and earphones associated with portable audio equipment Maximum sound pressure level measurement methodology and limit considerations Part 2 Guidelines to associate sets with headphones coming from different manufacturers Add the following NOTE Considered NOTE Z1 The use of certain substances in electrical and electronic equipment is restricted within the EU see Directive 2002 95 EC Add the following NOTE Not applicable NOTE Z1 In addition the instructions shall include as far as applicable a warning that excessive sound pressure from earphones and headphones can cause hearing loss Replace the
12. C for 7 days 168 h l Mounting of samples Samples are mounted vertically Test flame see IEC 60695 11 4 The test flame according to IEC 60695 11 4 is used Flame A B or C Flame A used p Compliance criteria Complied p TRF No IEC60950_1C A 1 1 SS me _ a gt EI N NN I P wji ON Nemko Page 30 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark Sample 1 burning time s The sample was not flammable and surgical cotton was not ignited Sample 2 burning time s The sample was not flammable and surgical cotton was not ignited Sample 3 burning time s The sample was not flammable and surgical cotton was not ignited Alternative test acc To IEC 60695 11 5 cl 5 and 9 Not used IN o Sample 1 burning time s j o Sample 2 burning time s A 3 buning time s S DELLES e S O aaz resposa OOo o ln Aaa comieron OOOO a ANNEX B MOTOR TESTS UNDER ABNORMAL CONDITIONS see 4 7 2 2 and kg 5 3 2 RES REG Si emer IN Ba enmol ln Ba _ Rumningovercastet HHT Si k n O ln Electric strength test test voltage V Running overload test for d c motors in secondary circuits asi Jee HH LN Sei een HH HTS Bss ere JL TRF No IEC60950_1C a Se SS N Nemko Page 31 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark Electric strength test test volt
13. TRF No IEC60950_1C N Nemko Page 41 of 46 Report No 175993 www nemko com 4 3 8 TABLE Batteries P Battery category eee Lithium ion for battery pack which is certified according to IEC 60950 1 For RTC battery lithium see below Manufacturer T See table 1 5 1 for details Type ue RE See table 1 5 1 for details Voltage tic ste coh teed eines See table 1 5 1 for details Capac E Dose Tested and Certified by incl Ref No UL see table 1 5 1 for details Circuit protection diagram 3 3VBAT C353 10U 10V X5R_8 T ani RTCRST ZN SHORT_PAD Q24 5VSUS O Max charge current during fault conditions Normal measured 3mA limit 300mA When D20 short circuit measured 4mA limit 300mA When R309 short circuit measured 4mA limit 300mA When Q24 1 3 short circuit measured 3mA limit 300mA When R306 short circuit measured 4mA limit 300mA When R298 short circuit measured 3mA limit 300mA MARKINGS AND INSTRUCTIONS 1 7 2 1 1 7 13 Location of replaceable battery In service access areas Language s English No see sub clause 1 7 13 Yes see sub clause 1 7 13 In the operating instructions TRF No IEC60950_1C Yes see sub clause 1 7 13 N Nemko Page 42 of 46 Report No 175993 www nemko com 4 3 8 TABLE Batteries p The tests of 4 3 8 are applicable only when appropriate battery
14. TT DEER RRC 2o21 fema RRC RMS working voltage N 21023 Peakworkingvotege O f 20s foams oo O S mai fema oooO S 24032 Mains vensiotvoleges OOO ln oO a AC mains supply f d Battery operation Transients from a c mains supply Transients from d c mains supply 2 10 3 8 Transients from telecommunication networks and cable distribution systems 2 Measurement of transient voltage levels P a Transients from a mains suplply i For an a c mains supply b Earthed d c mains supplies O o c Unearthed d c mains supplies iL 21033 9 For a d c mains supply b Transients from a telecommunication network CTI tests Semiconductor devices TRF No IEC60950_1C 3 4 4 4 5 5 5 10 10 10 10 10 10 10 N Nemko Page 18 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark 21056 ThinsheetmateielGererd ll 21057 Separabiethin shectmateral Jl Number of layers DCS see N 21058 Non separebe thinshestmateral OOO O y f 21058 Thinshestmateral standardtestprocedue w E A HT 210510 Thin sheet material denas est proceaue w E A HT 240511 insulation in wound rrer ln DEER RRC Working voltage a Basic insulation not under stress b Basic supplemetary reinforced insulation c Compliance with Annex U Two wires in contact inside wound component angle between 45 and 90 components Rer gennet TR
15. after 1 7 5 The equipment is regarded as class Ill equipment 1 7 5A Appliance Couplers If an appliance coupler according to IEC 60320 1 C 14 rated current 10 A is used in equipment whose rated voltage is less than 125 V and the rated current is over 10 A the following instruction or equivalent shall be described in the user instruction Use only designated cord set attached in this equipment 1 7 12 Replace first sentence with the following Must be considered when l marketing into Japan Instructions and equipment marking related to safety shall be in Japanese when disconnecting the earthing connection be sure to disconnect after pulling out the mains plug from the mains E NK In item b of this sub clause replace IEC Considered 60083 with JIS C 8303 2007 or Article 1 of the Ministerial Ordinance No 85 1962 1 7 17A Add the following new clause after 1 7 17 The equipment is regarded as class III equipment no 1 7 17A Marking for CLASS 01 EQUIPMENT earthing connection For CLASS 01 EQUIPMENT the following instruction shall be marked on the visible place of the mains plug or the main body UT PHO STT 5 TR SVS Provide an earthing connection Moreover for CLASS 01 EQUIPMENT the following or equivalent instruction shall be indicated on the visible place of the main body or written in the operating instructions rn T EMT I 7 ARo L ATIKFT 7 TFS NM EMEI SC d UTERT I Y xE b UV MEL T
16. an impulse test of 2 5 kV defined in EN 60950 1 2006 6 2 2 1 the additional testing shall be performed on all the test specimens as described in EN 132400 the impulse test of 2 5 kV is to be performed before the endurance test in EN 132400 in the sequence of tests as described inEN 132400 ON Nemko Page 11 of 12 Report No 175993 www nemko com IEC60950_1A ATTACHMENT Requirement Test Result Remark In Finland Norway and Sweden the exclusions No TNV circuits are applicable for PERMANENTLY CONNECTED EQUIPMENT PLUGGABLE EQUIPMENT TYPE B and equipment intended to be used in a RESTRICTED ACCESS LOCATION where equipotential bonding has been applied e g in a telecommunication centre and which has provision for a permanently connected PROTECTIVE EARTHING CONDUCTOR and is provided with instructions for the installation of that conductor by a SERVICE PERSON In Finland Norway and Sweden for Not connected to cable requirements see 6 1 2 1 and 6 1 2 2 of this distribution system annex The term TELECOMMUNICATION NETWORK in 6 1 2 being replaced by the term CABLE DISTRIBUTION SYSTEM In Norway and Sweden for requirements see Not connected to cable 1 2 13 14 and 1 7 2 1 of this annex distribution system In Norway for installation conditions see EN Not connected to cable 60728 11 2005 distribution system Sweden Ordinance 1990 944 No switch containing mercury Add the following in the equipment
17. considered to comply with the requirements Conditioning temperature C time weeks f Pe i OoN OoN H ES espace bie LE Reducing the risk of ignition and spread dame Method 1 is used P Be WM 4 4 Method 2 application of all of simulated fault condition tests 4 7 2 1 Parts requiring a fire enclosure The fire enclosure is required to cover all parts 4 7 2 2 Parts not requiring a fire enclosure The fire enclosure is required to cover all parts 1 4 7 3 1 General Components and materials have adequate flammability classification See appended table 1 5 1 and Annex A TRF No IEC60950_1C Method 1 selection and application of components see appended table 4 7 wiring and materials Conditions for a fire enclosure Refer below T T T ON Nemko Page 26 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark Materials for fire enclosures The fire enclosure is V 0 LCD bezel and keypad cover metal and glass LCD panel Glass complied with Annex A 2 4 7 3 3 Materials for components and other parts outside No parts outside the fire fire enclosures enclosure Materials for components and other parts inside fire Other materials inside the fire enclosures enclosure are minimum V 2 material 4 7 3 5 Materials for air filter assemblies No air filters in the equipment oN 4 7 3 6 Materials used in high voltage components No part
18. electrotechnical products Methods of test for the determination of the flammability of solid electrical insulating materials when exposed to an igniting source Index Between the entries polyimide insulating material Considered P and powder insert the following POTENTIAL IGNITION SOURCE 1 12 201 4 7 201 3 4 7 201 5 IEC 60950 1 ed 1 Page 1 of 3 www nemko com Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark ATTACHMENT SINGAPORE DIFFERENCES to IEC 60950 1 ed 1 The following is the national differences in accordance with safety authority website www safety org sq ref Singapore Consumer Protection Safety Requirements Information booklet chapter 7 page 23 26 Based on information by Singapore NCB PSB Corp 7 SAFETY AUTHORITY S REQUIREMENTS The Safety Authority monitors the safety of the controlled goods sold in Singapore by investigating all complaints incidents and accidents reported to the authority Experiences gained are translated into the Safety Authority s Requirements These requirements are to be fulfilled in addition to the applicable safety standards Applicable to all electrical products All appliances All appliances must be tested to 230 Class III equipment VAC Voltage selector Appliance fitted with voltage selector Class III equipment voltage mis shall be tested as follows match test Connect appliance to 230 VAC mains with voltage se
19. equipment in question In NO compliance with standards for radio interference suppression is a part of Nemko s certification In Fl DK and SE compliance is not necessary for achieving safety certification 1 5 1 AC DC adapter The maximum ambient temperature Tma of the following AC DC adapters is 40 C in power adapter CB test report However it has been evaluated and complied with the requirement for Tma 45 C in the CB test report 1 Bestec type NA0241WAA 2 Bestec type BT AG250SDFxy 1 7 2 1 Note 3 Instructions and equipment marking related to Language of safety markings instructions safety is applied in the language that is acceptable in the country in which the equipment is to be sold TRF No IEC60950_1C N Nemko Page 5 of 46 Report No 175993 www nemko com Summary of compliance with National Differences The sample s tested compliance with the requirements of IEC 60950 1 2005 2nd Edition and all CENELEC members as listed in EN 60950 1 2006 2nd Edition A11 2009 At the time of issuing this test report not all countries are listed for IEC 60950 1 2005 2nd Edition Therefore this test report includes national differences for IEC 60950 1 2001 1st Edition All national differences listed in the IECEE Online CB Bulletin are covered by the Common Modifications Special National Conditions National Deviations and the National Requirements noted above except for the following countries which are docu
20. in the external location where easily visible 3 Add the following after Table 3A Table 3A applies when cables complying with JIS C 3662 or JIS C 3663 are used In case of other cables the cable entries shall be so designed that a conduit suitable for the cable used can be fitted JIS C 0664 2003 class Ill equipment with JIS C 0664 2003 class Il equipment The equipment is regarded as class III equipment no earthing connection The equipment is regarded as class III equipment no earthing connection The equipment is regarded as class III equipment no earthing connection The equipment is regarded as class III equipment no earthing connection The equipment is not intended for permanent connection to the mains Test results according to last modification date 2010 11 27 in CB Bulletin N Nemko www nemko com IEC 60950 1 2001 Requirement Test Result Remark Add the following to the last of first dashed The equipment is regarded as paragraph class III equipment no power cord used Page 6 of 12 Report No 175993 Or mains cords shall be of the sheathed type complying with Appendix 1 of Article 1 of the Ministerial Ordinance No 85 1962 on stipulating technical requirements for the Electrical Appliance Add the following to the last of second dashed paragraph Or mains cords shall be of the sheathed type complying with Appendix 1 of Article 1 of the Ministerial Ordinance No 85 1962 o
21. installation and maintenance additional construction performance and marking requirements are applicable to determine the adequacy of the slide rails Test results according to last modification date 2007 08 08 in CB Bulletin IEC 60950 1 ed 2 www nemko com IEC 60950 1 2005 Page 6 of 8 Report No 175993 Requirement Test Result Remark 4 3 2 Loading test for equipment with handle s used to The handle is not intended to N support more than 9 kg support more than 9 0kg no special loading test required 4 3 6 In addition to the IEC requirements Direct Plug in Not intended to plug directly N Equipment complies with UL 1310 into a wall socket outlet 4 3 12 The max quantity of flammable liquid stored in No flammable liquids within N equipment per ANSI NFPA 30 Table NAE 6 the equipment 4 3 12 Equipment using replenishable liquids marked to No flammable liquids within N indicate type of liquid to be used the equipment 4 3 13 2 Equipment that produces x radiation and does not The equipment does not P comply with 4 3 12 under all conditions of servicing generate ionizing radiation marked to indicate the presence of radiation 4 3 13 5 Requirements contained in the applicable national No laser and LEDs are P codes apply to lasers 21 CFR 1040 diffusive type 47 Automated information storage equipment intended The equipment has no N to con
22. on the Ministerial Ordinance stipulating Technical Specifications for Electrical Appliances Commerce and Distribution Policy Group No 3 2008 06 19 may apply Add a note after the first paragraph as follows NOTE Attention should be drawn to that majority of three phase power system in Japan is of delta connection and therefore in that case the test is conducted using the test circuit from IEC 60990 figure 13 Replace Table 5A as follows Terminal A of measuring instrument connected to Type of equipment All equipment HAND HELD MOVABLE other than HAND HELD but including TRANSPORTABLE EQUIPMENT STATIONARY PLUGGABLE TYPE A All other STATIONARY EQUIPMENT not subject to the conditions of 5 1 7 subject to the conditions of 5 1 7 HAND HELD Accessible parts and circuits not connected to protective earth Equipment main protective earthing terminal if any CLASS EQUIPMENT Equipment main protective earthing terminal if any CLASS 01 EQUIPMENT ae The equipment is regarded as class III equipment Maximum TOUCH PROTECTIVE CURRENT CONDUCTOR mA r m s CURRENT Poo Maximum 1 If peak values of TOUCH CURRENT are measured the maximum values obtained by multiplying the r m s values by 1 414 Replace IEC 60664 1 in NOTE 4 with JIS C No TNV circuit in the 0664 equipment Test results according to last modification date 2010 11 27 in CB Bulletin N Nemko www nemk
23. other equipment or a network shall system if safety relies on connection to protective earth or if surge Suppressors are connected between the network terminals and accessible parts have a marking stating that the equipment must be connected to an earthed mains socket outlet The marking text in the applicable countries shall be as follows In Finland Laite on liitettava suojakoskettimilla varustettuun pistorasiaan ON Nemko Page 5 of 12 www nemko com IEC60950_1A ATTACHMENT Requirement Test Result Remark In Norway Apparatet ma tilkoples jordet stikkontakt In Sweden Apparaten skall anslutas till jordat uttag In Norway and Sweden the screen of the cable distribution system is normally not earthed at the entrance of the building and there is normally no equipotential bonding system within the building Therefore the protective earthing of the building installation need to be isolated from the screen of a cable distribution system It is however accepted to provide the insulation external to the equipment by an adapter or an interconnection cable with galvanic isolator which may be provided by e g a retailer The user manual shall then have the following or similar information in Norwegian and Swedish language respectively depending on in what country the equipment is intended to be used in Equipment connected to the protective earthing of the building installation through the mains con
24. power supply cord set not supplied by Registered Supplier IEC 60950 1 2001 Requirement Detachable power cord set must be listed in the test report critical component list Circuit diagrams must be indicated with component s values for products tested to IEC 60065 and IEC 60950 Circuit diagrams of the electronic modules in the electrical appliances must be provided Controlled goods having an enclosure which is shaped and decorated so that it is likely to be treated as a toy by children shall not be accepted for certification and registration Applicable to AC adaptor Test report showing that the 3 pin complied with sub clauses 12 1 amp 12 3 of SS 246 must be submitted The 2 pin Appendix W shall comply with IEC 83 1975 Standard C5 Version Il or EN 50075 Registered Supplier who is not supplying the detachable power supply cord set together with the AC Adaptor must provide written instruction to its customer on the type of approved detachable power cord set to use Page 2 of 3 Report No 175993 Requirement Test Result Remark Verdict Result Remark Class III equipment Must be considered when marketing in Singapore Must be considered when marketing in Singapore The shape and function are not considered as toy Class III equipment Class III equipment Class IIl equipment Test results according to last modification date 2007 05 29 in CB Bulletin IE
25. rated more than 1 3 hp locked rotor current over 43 A 3 4 8 Vertically mounted disconnect switches and circuit No switch acting as breakers are required to have the on position disconnect device indicated by the handle in the up position 3 4 11 For computer room applications equipment with No battery capable of battery systems capable of supplying 750 VA for supplying 750VA five minutes are required to have a battery disconnect means that may be connected to the computer room remote power off circuit Battery system EE No such battery system When power off is activated sese eee 4 3 12 The maximum quantity of flammable liquid stored in No flammable liquids within equipment is required to comply with NFPA 30 the equipment Flammable liquid material eee eee eee Container mate al a icskesdavescasadaeresaaaadsanaaausaensca Storage container SIZE x5 sscseacassusnasvenvenaanassenacdezsanncs 4 3 13 5 Equipment with lasers is required to meet the No laser and LEDs are Canadian Radiation Emitting Devices Act REDR diffusive type C1370 and or Code of Federal Regulations 21 CFR 1040 as applicable For computer room applications automated The equipment has no information storage systems with combustible combustible area greater than media greater than 0 76 m 27 cu ft are required 0 76 m to have a provision for connection of either automatic sprinklers or a gaseous agent extinguishing system with an extended discharge
26. sectional area sectional area in mm mm see note 2 Over 0 2 up to and including 3 05 18 0 8 Over 3uptoandincluding 7 5 0 75 16 1 3 Over 7 5 up to and including 10 0 75 1 00 16 1 3 Over 10 up to and including 16 1 0 1 5 14 2 Replace footnote 1 with the following gi D This nomina cross sectional area is only allowed for Class I appliances if the length of the power supply cord measured between the point where the cord or cord guard enters the appliance and the entry to the plug does not exceed 2 m 0 5 mm three core supply flexible cords are not permitted see AS NZS 3191 Delete Note 1 4 3 6 Replace paragraph three with Not intended to plug directly Equipment with a plug portion suitable for insertion deer into a 10 A 3 pin flat pin socket outlet complying with AS NZS 3112 shall comply with the requirements in AS NZS 3112 for equipment with integral pins for insertion into socket outlets or AS NZS 2211 1 PETERS SES 4 7 Aad the following paragraph Refer to below EJ IEC 60950 1 ed 1 Page 3 of 8 www nemko com Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark Aad the following after Clause 4 7 3 6 All materials have suitable 4 7 201 Resistance to fire Alternative tests HEEN required 4 7 201 1 General Parts of non metallic material shall be resistant to ignition and spread of fire This requirement does not apply to decorative t
27. subclause as follows Class III equipment Basic requirements To protect against excessive current short circuits and earth faults in PRIMARY CIRCUITS protective devices shall be included either as integral parts of the equipment or as parts of the building installation subject to the following a b and c a except as detailed in b and c protective devices necessary to comply with the requirements of 5 3 shall be included as parts of the equipment b for components in series with the mains input to the equipment such as the supply cord appliance coupler r f i filter and switch short circuit and earth fault protection may be provided by protective devices in the building installation ON Nemko www nemko com IEC60950_1A ATTACHMENT Requirement Test Result Remark Page 3 of 12 Report No 1 rating of the wall socket outlet This subclause has been declared void Class III equipment 3 2 3 Delete the NOTE in Table 3A and delete also in Class IIl equipment this table the conduit sizes in parentheses 3 2 5 1 Replace 60245 IEC 53 by H05 RR F Class III equipment 60227 IEC 52 by H03 VV F or H03 VVH2 P 60227 IEC 53 by H05 VV F or H05 VVH2 F2 In Table 3B replace the first four lines by the following Up to and including 6 0 75 Over 6 up to and including 10 0 75 N 4 0 Over 10 up to and including 16 1 0 9 1 6 In the conditions applica
28. with special loading tests Equipment intended to receive telecommunication ringing signals is required to comply with a special touch current measurement tests Ringing ports provided ss sssssss sese se esse esse eenn Simulation provided to sss eee eenn Measured total touch current Internal e g card cage SELV circuit connectors and printed wiring board connectors that are accessible to the operator and that deliver power are to be overloaded During abnormal operating testing if a circuit is interrupted by the opening of a component the test shall be repeated twice three tests total using new components as necessary Equipment intended for connection to telecommunication network outside plant cable is required to be protected against overvoltage from power line crosses in accordance with 6 4 and Annex NAC Continuous ringing signals up to 16 mA only are permitted if the equipment is subjected to special installation and performance restrictions TRF No CSA60950 1 07A b1070423 Class III equipment No CRTs in the equipment No mounting on racks and provided with slide rails The handle is not intended to support more than 9 0kg no special loading test required Not connected to a telecommunication network The SELV connectors comply with LPS no testing required No test interrupted by opening of a component No TNV circuits No TNV circuits Test results according to last modific
29. 0 mm and a height of 50 mm shall be subjected to the needle flame test However parts shielded by a barrier which meets the needle flame test shall not be tested The needle flame test shall be made in accordance with AS NZS 4695 2 2 with the following modifications Clause of Change ASINZS 4695 2 2 5 Severities Replace with The duration of application of the test flame shall be 30 s 1 s 8 Test procedure 8 2 Replace the first sentence with The specimen shall be arranged so that the flame can be applied to a vertical or horizontal edge as shown in the examples of figure 1 The first paragraph does not apply Addition If possible th flame shall be applied at least 10 mm from a corner Replace with The test shall be made on one specimen If the specimen does not withstand the test the test may be repeated on two further specimens both of which shall then withstand the test ge 10 Evaluation of test Replace with results The duration of burning t shall not exceed 30s However for printed circuit boards it shall not exceed 15 s IEC 60950 1 ed 1 Page 5 of 8 www nemko com Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark The needle flame test shall not be carried out on All materials have suitable parts of material classified as V 0 or V 1 according o flame class no testing IEC 60695 11 10 provided that the sample tested required w
30. 29 in CB Bulletin IEC 60950 1 ed 2 www nemko com IEC 60950 1 2005 Page 1 of 7 Report No 175993 Requirement Test Result Remark National Differences for Canada P Canada and the United States of America have adopted a single bi national standard CAN CSA C22 2 No 60950 1 UL60950 1 Second Edition which is based on IEC 60950 1 Second Edition This bi national standard should be consulted for further details on the national conditions and differences summarized below SPECIAL NATIONAL CONDITIONS The following is a summary of the key national differences based on national regulatory requirements such as the Canadian Electrical Code CEC Part and the Canadian Building Code which are referenced in legislation and which form the basis for the rules and practices followed in electrical and building installations TH 1 4 14 S RC ol gt oa All equipment is to be designed to allow installation in accordance with the National Electrical Code NEC ANSI NFPA 70 the Canadian Electrical Code CEC Part I CAN CSA C22 1 and when applicable the National Electrical Safety Code IEEE C2 Also unless marked or otherwise identified installation is allowed per the Standard for the Protection of Electronic Computer Data Processing Equipment ANSI NFPA 75 For Pluggable Equipment Type A the protection in the installation is assumed to be 204 For lengths exceeding 3 05 m external interconnecti
31. 3 2 9 Adequate wire bending space and volume of field Class Ill equipment N wiring compartment required to properly make the field connections 3 2 9 Equipment solely for installation in Restricted Equipment not intended for N Access Locations using low voltage d c systems installation in RAL Test results according to last modification date 2007 08 08 in CB Bulletin IEC 60950 1 ed 2 Page 5 of 8 www nemko com Report No 175993 IEC 60950 1 2005 Requirement Test Result Remark may not need provision for connecting and securing a field wiring system when wiring is protected from abuse 3 3 Field wiring terminals provided for interconnection of Class III equipment N units for other then LPS or Class 2 circuits also comply with 3 3 3 3 Interconnection of units by LPS or Class 2 Class II equipment N conductors may have field wiring connectors other than specified in 3 3 if wiring is reliably separated 3 3 1 Terminals for the connection of neutral conductor Class II equipment N identified by a distinctive white marking or other equally effective means 3 3 3 Wire binding screw terminal permitted for Class II equipment N connection of No 10 AWG 5 3 mm or smaller conductor if provided with upturned lugs cupped washer or equivalent retention 3 3 4 Terminals accept US wire sizes gauge Class Ill equipment N 3 3 4 Terminals accept current carrying conductors rated
32. 4 unless exempted by those regulations NOTE Standard plug is defined in SI 1768 1994 and essentially means an approved plug conforming to BS 1363 or an approved conversion plug 3 2711 In Ireland apparatus which is fitted with a flexible Class II equipment cable or cord and is designed to be connected to a mains socket conforming to l S 411 by means of that flexible cable or cord and plug shall be fitted with a 13 A plug in accordance with Statutory Instrument 525 1997 National Standards Authority of Ireland section 28 13 A Plugs and Conversion Adaptors for Domestic Use Regulations 1997 In Switzerland for requirements see 3 2 1 1 of Class III equipment this annex 1 In the United Kingdom a power supply cord with Class Il equipment conductor of 1 25 mm2 is allowed for equipment with a rated current over 10 A and up to and including 13 A In the United Kingdom the range of conductor Class II equipment sizes of flexible cords to be accepted by terminals for equipment with a RATED CURRENT of over 10 A up to and including 13 A is 425 mm to 1 5 mm nominal cross sectional In the United Kingdom the torque test is Class III equipment performed using a socket outlet complying with BS 1363 part 1 1995 including Amendment 1 1997 and Amendment 2 2003 and the plug part of DIRECT PLUG IN EQUIPMENT shall be assessed to BS 1363 Part 1 12 1 12 2 12 3 12 9 12 11 12 12 12 13 12 16 and 12 17 except that
33. 4 7 3 1 For computer room applications enclosures with The equipment has no combustible material measuring greater than 0 9 m combustible material greater 10 sq ft or a single dimension greater than 1 8 than 0 9m or single m 6 ft are required to have a flame spread rating gimension greater than 1 8m of 50 or less For other applications enclosures with the same dimensions require a flame spread rating of 200 or less Annex H Equipment that produces ionizing radiation is The equipment does not required to comply with the Canadian Radiation produce ionizing radiation Emitting Devices Act REDR C1370 and or Code of Federal Regulations 21 CFR 1020 as applicable Ces N OT O D DI gt gt Qa o5 Sct Ts TRF No CSA60950 1 07A b1070423 Test results according to last modification date 2008 07 31 in CB Bulletin IEC 60950 1 ed 2 Page 4 of 7 www nemko com Report No 175993 IEC 60950 1 2005 Clause Requirement Test Result Remark Verdict OTHER DIFFERENCES The following key national differences are based on requirements other than national regulatory requirements La Some components and materials associated with Critical components are IEC the risk of fire electric shock or personal injury are certified See list of critical required to have component or material ratings in components in main CB report accordance with the applicable national Canadian 1 5 1 There may be and or U S compo
34. 5 4 Transformers No isolating transformer in the equipment 1 5 5 Interconnecting cables No interconnecting cables 1 5 6 Capacitors bridging insulation No primary circuit 1 5 7 Resistors bridging insulation No such resistor used 1 5 7 1 Resistors bridging functional basic or supplementary insulation 1 5 7 2 Resistors bridging double or reinforced insulation between a c mains and other circuits 1 5 7 3 Resistors bridging double or reinforced insulation between a c mains and antenna or coaxial cable 1 5 8 Components in equipment for IT power systems The equipment is regarded as Class Ill 1 5 9 Surge suppressors No such component used 1 5 9 2 Protection of VDRs Ce 1 5 9 3 Bridging of functional insulation by a VDR TRF No IEC60950_1C ON Nemko Page 10 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark 1 5 9 4 Bridging of basic insulation by a VDR PN 1 5 9 5 Bridging of supplementary double or reinforced insulation by a VDR Power interface p AC power distribution systems The equipment is regarded as SN Class Ill Input current see appended table 1 6 2 P 1 6 3 Voltage limit of hand held equipment The equipment is not hand held 1 6 4 Neutral conductor The equipment is regarded as Class Ill Marking and instructions p The required marking is located in the battery pack compartment of the equipment zvao asv E na 5031 is used Rat
35. 6 2 1 a 7 0 kV for hand held telephones and for headsets and 2 5 kV for other equipment and for 6 2 1 b and 6 2 1 c 1 5 kV NOTE 201 The 7 kV impulse simulates lightning surges on typical rural and semi rural network lines NOTE 202 The 2 5 kV for 6 2 1 a was chosen to ensure adequacy of the insulation concerned and does not necessarily simulate likely overvoltages Add the symbol NZ in the right hand margin beside No TNV circuits the second paragraph Delete the Note Aad the following after the second paragraph In Australia this variation does not apply in New Zealand the a c test voltage is for 6 2 1 a 3 kV and for 6 2 1 b and 6 2 1 c 1 5 kV NOTE 201 Where there are capacitors across the insulation under test it is recommended that d c test voltages are used NOTE 202 The 3 kV and 1 5 kV values have been determined considering the low frequency induced voltages from the power supply distribution system IEC 60950 1 ed 1 Page 8 of 8 www nemko com Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark Annex P Add the following Normative References to Annex Considered P P IEC 60065 Audio Video and similar electronic apparatus Safety requirements AS NZS 3191 Approval and test specification Electric flexible cords AS NZS 3112 Approval and test specification Plugs and socket outlets AS NZS 4695 707 Fire hazard testing of
36. 93 www nemko com IEC60950_1A ATTACHMENT Requirement Test Result Remark In Denmark socket outlets for providing power to Class III equipment other equipment shall be in accordance with the Heavy Current Regulations Section 107 2 D1 Standard Sheet DK 1 3a DK 1 5a or DK 1 7a when used on Class equipment For STATIONARY EQUIPMENT the socket outlet shall be in accordance with Standard Sheet DK 1 1b or DK 1 5a For CLASS Il EQUIPMENT the socket outlet shall be in accordance with Standard Sheet DKA 1 4a In Norway for requirements see 1 7 2 1 6 1 2 1 No TNV circuits and 6 1 2 2 of this annex In Finland Norway and Sweden there are No TNV circuits additional requirements for the insulation See 6 1 2 1 and 6 1 2 2 of this annex In Norway for requirements see 1 7 2 1 6 1 2 1 No TNV circuits and 6 1 2 2 of this annex In the United Kingdom the current rating of the Class III equipment circuit shall be taken as 13 A not 16 A In the United Kingdom to protect against Class III equipment excessive currents and short circuits in the PRIMARY CIRCUIT of DIRECT PLUG IN EQUIPMENT tests according to 5 3 shall be conducted using an external protective device rated 30 A or 32 A If these tests fail suitable protective devices shall be included as integral parts of the DIRECT PLUG IN EQUIPMENT so that the requirements of 5 3 are met In Finland Norway and Sweden there are No TNV circuits addi
37. C 60950 1 ed 1 Page 3 of 3 www nemko com Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark Applicable to computer products CD DVD ROM Test certificate showing that No CD DVD ROM used in personal CD DVD ROM has complied with computer IEC 825 must be provided Modem Card used Modem card incorporated in the No modem card in personal personal computer must be tested computer at set level sub clauses 5 1 amp 6 of IEC 60950 or at component level Applicable to plasma LCD display monitor Plasma LCD Plasma LCD display monitor tested No TV tuner display monitor to IEC 60950 would require with TV tuner additional test to clauses 9 related to antenna only 10 1 10 2 10 3 and 12 5 of IEC 60065 Test results according to last modification date 2007 05 29 in CB Bulletin N Nemko www nemko com Page 1 of 12 Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark National Differences for JAPAN Differences according to J60950 1 H22 National Differences Japan 1 2 4 1 Add the following new NOTE The equipment is regarded as class Ill equipment NOTE Even if the equipment is designed as Class I the equipment is regarded as Class Ol equipment when a 2 pin adaptor with an earthing lead wire or a cord set having a 2 pin plug with an earthing lead wire is provided or recommended 1 2 4 3A Add the following new clause The equipment is regarded a
38. Class III equipment N 125 of the equipment current rating 3 3 6 Field wiring terminals marked to indicate the Class II equipment N material s of the conductor for the terminals used 3 3 6 Aluminum conductors not permitted for connection Class III equipment N to terminal for equipment earthing conductor 3 3 6 Field wiring connections made through the use of Class Il equipment N suitable pressure connectors including set screw type solder lugs or splices to flexible leads 3 4 2 Separate motor control device s required for cord No AC motors in the N connected equipment rated more than 12 A or with equipment motor rated more than 1 3 hp or more than 120 V 3 4 8 Vertically mounted disconnect devices oriented so No switch acting as disconnect N up position of handle is on device 3 4 11 For computer room applications equipment with No battery capable of N battery systems capable of supplying 750 VA for 5 supplying 750VA minutes provided with battery disconnect means 4 2 8 1 Special opening restrictions for enclosures around No CRTs in the equipment N CRTs with face dimension of 160 mm or more 4 2 9 Compartment housing high pressure lamp marked No high pressure lamp N to indicate risk of explosion provided 4 2 11 For equipment mounted on racks and provided with No mounting on racks and N slide rails allowing the equipment to slide away from provided with slide rails the rack for
39. Fall test Impact test not applicable refer cl 4 2 6 Swing test Drop test height mm Transportable equipment No damage after 1m drop Stress relief test Test is carried out at 70 5 C 7h for all shapes of enclosures No risk of shrinkage or distortion on enclosures due to release of internal stresses 4 2 8 Cathode ray tubes CRT s not used in the equipment Picture tube separately certified 4 2 9 High pressure lamps No high pressure lamps in the equipment Wall or ceiling mounted equipment force N Not intended to be mounted on a wall or ceiling f Design and construction 4 3 1 Edges and corners All edges and corners are rounded and or smoothed 4 3 2 Handles and manual controls force N Considered The force 50N is applied on the handle for 1 min and without hazard 4 3 3 Adjustable controls No hazardous adjustable controls 4 2 5 gt A N P B N a O A w TRF No IEC60950_1C ON Nemko Page 23 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark Securing of parts No loosening of parts impairing creepage distances or clearances is likely to occur Connection by plugs and sockets SELV connectors do not comply with IEC 60320 1 or IEC 60083 Direct plug in equipment Class III equipment oN 4 3 7 Heating elements in earthed equipment No heating elements provided Overcharging of a rechargeable ba
40. H PATT 3 PSL Provide an earthing connection before the mains plug is connected to the mains And Test results according to last modification date 2010 11 27 in CB Bulletin N Nemko www nemko com Page 5 of 12 IEC 60950 1 2001 Report No 175993 Requirement Test Result Remark Add the following after the first paragraph This also applies to the conductor of lead wire for protective earthing of CLASS 0 EQUIPMENT Replace the first paragraph with the following Equipment required to have protective earthing shall have a main protective earthing terminal For equipment with a DETACHABLE POWER SUPPLY CORD the earthing terminal in the appliance inlet is regarded as the main protective earthing terminal except for CLASS 0 EQUIPMENT providing separate main protective earthing terminal other than appliance inlet Replace the first sentence with the following 2 6 4 2 2 6 5 4 2 6 5 8A 2 6 3 2 Protective earthing connections of CLASS EQUIPMENT shall make earlier and break later than the supply connections in each of the following Add the following new clause after 2 6 5 8 2 6 5 8A Earthing of CLASS 01 EQUIPMENT Plugs with a lead wire for earthing shall not be used for equipment having a rated voltage exceeding 150 V For plugs with a lead wire for earthing the lead wire shall not be earthed by a clip CLASS 01 EQUIPMENT shall be provided with an earthing terminal or a lead wire for earthing
41. K 2 5a If poly phase equipment and single phase equipment having a RATED CURRENT exceeding 13 A is provided with a supply cord with a plug this plug shall be in accordance with the Heavy Current Regulations Section 107 2 D1 or EN 60309 2 In Spain supply cords of single phase equipment Class Il equipment having a rated current not exceeding 10 A shall be provided with a plug according to UNE 20315 1994 Supply cords of single phase equipment having a rated current not exceeding 2 5 A shall be provided with a plug according to UNE EN 50075 1993 CLASS EQUIPMENT provided with socket outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with standard UNE 20315 1994 If poly phase equipment is provided with a supply cord with a plug this plug shall be in accordance with UNE EN 60309 2 ON Nemko Page 8 of 12 Report No 175993 www nemko com IEC60950_1A ATTACHMENT Requirement Test Result Remark In the United Kingdom apparatus which is fitted Class IIl equipment with a flexible cable or cord and is designed to be connected to a mains socket conforming to BS 1363 by means of that flexible cable or cord and plug shall be fitted with a standard plug in accordance with Statutory Instrument 1768 1994 The Plugs and Sockets etc Safety Regulations 199
42. M2 UL A K S E V Cor 12Vdc 2 0A R Tma 40 C NA0241WAA is used Bestec Power BT AG250SDFxy I P 100 240V IEC 60950 1 CB by Electronics Co x A Z or blank 50 60Hz 0 4A ed 2 UL Demko DK Ltd y A Z or blank For Cl Il O P UL 60950 1 19690 UL marketing purpose 13 5Vdc 1 85A Tma 40 C Darfon BBOJ C I P 100 240V IEC 60950 1 CB by TUV SUD Electronics 50 60HZz 1A ed 2 A1 SG OF 05619 Corp Cl Il O P 2009 UL 13 5Vdc 1 85A UL 60950 1 25W max Tma 45 C Main Li lon Shanghai BYD CL1 6 5Vdc IEC 60950 1 CB by TUV battery pack Company 3100mAh 2005 ed 2 SUD SG OF Limited ami 05784 SG BT IEC 62133 00055 UL 2002 UL 60950 1 Enclosure Chi Mei PC 540 V 0 min 1 5mm UL 94 UL material Corporation thickness 70 C for top enclosure used only Enclosure Chi Lin PB 1201 V 0 min UL 94 UL material Technology 1 32mm for all thickness min enclosures 60 C LCD panel Various Various 7 5 TFT glass Tested in the type min 0 34 equipment mm thick with see annex A 2 LED back light module RTC battery Panasonic ML1220 Max charging UL 1642 UL MH12210 lithium voltage 12Vdc max charging current 300mA Power RICHTEK RT9703 series 2 5 5 5Vdc 3 2A UL subject UL distribution GMT G5282 Series 2 0 5 5Vdc 1 0 2367 UL switch U5 A for USB ports optional TRF No IEC60950_1C N Nemko Page 37 of 46 Report No 175993
43. NEX T GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER see 1 1 2 U ANNEX U INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED INSULATION see 2 10 5 12 ANNEX V AC POWER DISTRIBUTION SYSTEMS see 1 6 1 ON W ANNEX W SUMMATION OF TOUCH CURRENTS w wa Touchurenttomelecroniecreuts IJL CE a S wiz femeas O SS ln w 2 Jaeger of sover eaupmens 1 La w23 Jee HH a w22 Common reum zeiten 1 In TRF No IEC60950_1C N Nemko Page 35 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark W 2 3 Common return connected to protective earth PN ANNEX X MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS see clause ae C 1 H ULTRAVIOLET LGT CONDTIONNG TEST 648183 TW Mounting of test samples Carbon arc light exposure apparatus Xenon arc light exposure apparatus ANNEX Z OVERVOLTAGE CATEGORIES see 2 10 3 2 and Clause G 2 oN AA ANNEX AA MANDREL TEST see 2 10 5 8 N BB ANNEX BB CHANGES IN THE SECOND EDITION TRF No IEC60950_1C N Nemko Page 36 of 46 Report No 175993 www nemko com 1 5 1 TABLE list of critical components P object part No manufacturer type model technical data standard mark s of trademark conformity AC DC adapter Bestec Power NAwwwiWyA I P 100 240V IEC 60950 1 CB by TUV RH Electronics Co www can be 015 50 60Hz 1 0A ed 2 JPTUV Ltd 024 y can be D W CI Il O P UL 60950 1 031002
44. No hazard limit 3100mA TRF No IEC60950_1C Page 45 of 46 Report No 175993 www nemko com Component Fault Supply Test Fuse Fuse Observation No voltage time current PQ32 pini 8 PR185 PQ64 pini 5 Data ports USB CNB pin 1 to RTN USB CNB pin 2 4 to RTN USB CN9 pin 1 to RTN USB CN9 pin 2 4 to RTN USB CN14 pin 1 to RTN USB CN14 pin 2 4 to RTN pin 10 to RTN pin 1 9 11 13 to RTN i k rf it MIC port 13 5 All pins to RTN OV Headphone port 13 5 All pins to RTN Supplementary information s c short circuit o c open circuit o lI overload TRF No IEC60950_1C Charging current for battery pack 1 74A No hazard limit 3100mA Charging current for battery pack 1 68A No hazard limit 3100mA Charging current for battery pack 2 98A No hazard limit 3100mA Maximum available current 3300mA 4 96V no hazard Maximum available current OmA OV no hazard Maximum available current 3300mA 4 96V no hazard Maximum available current OmA OV no hazard Maximum available current 3310mA 4 96V no hazard Maximum available current OmA OV no hazard Maximum available current OmA 2 22V no hazard Maximum available current OmA OV no hazard Maximum available current OmA no hazard Maximum available current OmA OV no hazard N Nemko Page 46 of 46 Report No 175993 www nemko com C 2
45. Remark Replace the last paragraph of this annex by The unit does not emit X ray N At any point 10 cm from the surface of the radiation OPERATOR ACCESS AREA the dose rate shall not exceed 1 uSv h 0 1 mR h see NOTE Account is taken of the background level Replace the notes as follows NOTE These values appear in Directive 96 29 Euratom Delete NOTE 2 Bibliography Additional EN standards In Denmark certain types of Class appliances see 3 2 1 1 may be provided with a plug not establishing earthing conditions when inserted into Danish socket outlets 1 2 13 14 In Norway and Sweden for requirements see No such part 1 7 2 1 and 7 3 of this annex L In Finland Norway and Sweden resistors Class III equipment bridging BASIC INSULATION in CLASS PLUGGABLE EQUIPMENT TYPE A must comply with the requirements in 1 5 7 1 In addition when a single resistor is used the resistor must withstand the resistor test in 1 5 7 2 1 5 8 In Norway due to the IT power system used see Class II equipment annex V Figure V 7 capacitors are required to be rated for the applicable line to line voltage 230 V 1 5 9 4 In Finland Norway and Sweden the third dashed sentence is applicable only to equipment as defined in 6 1 2 2 of this annex 1 7 2 1 In Finland Norway and Sweden CLASS Class III equipment and not PLUGGABLE EQUIPMENT TYPE A intended for connected to cable distribution connection to
46. TABLE transformers N Tested insulation Working Working Required Required Required Required voltage voltage electric clearance creepage distance peak V rms V strength mm distance thr insul mm 2 10 2 2 10 2 5 2 2 10 3 2 10 4 2 10 5 Test Measured Measured Measured voltage clearance creepage distance V mm dist mm thr insul mm number of layers Supplementary information TRF No IEC60950_1C Page 1 of 5 Photos Gul BE www nemko com 175993 Report No Page 2 of B Photos Gul BE www nemko com 175993 Report No Page 3 of 5 ON Nemko Photos www nemko com Report No 175993 U V DOL 06 o OL OS S OF 08 OZ Ot OOE 06 08 OL 09 0S o SN Hd St WH MI Boa DS Of CC hie 09 0S Op op J ppp e n m vn OL 0006 98 oL o9 OS OF oe co 007 0 Lk COL gd GL to ae OF Page 4 of 5 www nemko com Report No nlnm Ui Junk S E g 3 2 g S 8 8 S S E 8 a 3 g njun mt uj 08 OL 09 OS Ov OF OZ OL QOLOS Page 5 of B ON Nemko Photos www nemko com Report No 175993 Main board MAM 0 OP WWW HMM HA DI 08 06 00L OL DS T HIHHH mm 1 mnnt ui OD ITT MPTE EN UA A K g d 007 0 08 OL 09 0S OY Of G Ol NOL 06 08 08 0L 09 oG Ov OF Oz ol ON Nemko Page 1 of 12 Report No 175993 www nemko com IEC60950_1A ATTACHMENT Requirement Test Result Remark
47. Test Report issued under the responsibility of www nemko com TEST REPORT IEC 60950 1 Information technology equipment Safety Part 1 General requirements Report Reference No 175993 Date of esue A June 21 2011 Total number of pages sees eee 46 pages and refer to list of attachments on page 6 CB Testing Laboratory Name Nemko Taiwan Phone 886 2 8797 8790 5FL No 409 Section 2 Tiding Blvd Neihu Taipei 114 Taiwan Quanta Computer Inc No 188 Wen Hwa 2nd Road Kuei Shan Hsiang Tao Yuan Shien 333 Taiwan Quanta Computer Inc No 188 Wen Hwa 2nd Road Kuei Shan Hsiang Tao Yuan Shien 333 Taiwan See name and address of production sites See name and address of production sites Test specification Standard IEC 60950 1 2005 2nd Edition Test procedure Non standard test method Test Report Form No IEC60950_1A Test Report Form s Originator SGS Fimko Ltd Master TRF Dated 2009 09 Copyright 2009 IEC System for Conformity Testing and Certification of Electrical Equipment IECEE Geneva Switzerland All rights reserved This publication may be reproduced in whole or in part for non commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material IECEE takes no responsibility for and will not assume liability for damages resulting from the reader s interpretation of the reproduced material due to its placement and context If this Test Repo
48. Up to 2 000m Up to 2 000m Max 1 32 kg Dimensions 230 by 247 by 33 mm Possible test case verdicts Date s of performance of tests test case does not apply to the test object N N A test object does meet the requirement see P Pass test object does not meet the requirement F Fail TEU EE Date of receipt of test Hem May 2011 May June 2011 TRF No IEC60950_1C N Nemko Page 8 of 46 Report No 175993 www nemko com General remarks The test results presented in this report relate only to the object tested This report shall not be reproduced except in full without the written approval of the Issuing testing laboratory See Enclosure refers to additional information appended to the report See appended table refers to a table appended to the report Throughout this report a point is used as the decimal separator General product information The EUT is a Class Il Laptop Computer OLPC The unit will be connected to a certified AC DC adapter ref list of critical components The unit was configured as follows CPU VIA type C7 M Battery pack and LCD panel with LED back light The EUT has following data ports USB 3 MIC 1 headphone 1 SD Card reader 1 If nothing else stated testing was conducted with AC DC adapter output 13 5Vdc 1 85A to represent the worst case Circuit characteristics The equipment c
49. Working voltage ON ON el H Basic insulation not under stress PN Supplemetary reinforced insulation PN 2 10 6 3 Insulation between conductors on the same inner surface of a printed board 2 10 6 4 Insulation between conductors on different surfaces of a printed board rr Distance through insulation 2 10 7 Component external terminations PN TRF No IEC60950_1C N Nemko Page 19 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark 2 10 8 Tests on coated printed boards and coated components 23083 _ Semple preparator and preiminanyinapecion 2082 memaca HH 21083 eene S 21084 masones O 2109 meman ln 2 10 10 Test for Pollution Degree 1 environment and insulating compound 2 10 11 Tests for semiconductor devices and cemented S joints 2 10 12 Enclosed and sealed parts Po WIRING CONNECTIONS AND SUPPLY Current rating and overcurrent protection Adequate cross sectional areas on internal wiring 3 1 1 3 1 2 Protection against mechanical damage Wireways are smooth and free from edges Wires are adequately fixed to prevent excessive strain on wire and terminals and avoiding damage to the insulation of the conductors Securing of internal wiring Internal wiring is secured against excessive strain loosening of terminals and damage to the conductor insulation Beads and ceramic insulators No beads or similar ceramic insulators on conductors Insulatio
50. able to be installed in accordance with __ Considered P the National Electrical Code ANSI NFPA 70 1 1 1 Equipment able to be installed in accordance with __ Considered P ANSI NFPA 75 and NEC Art 645 unless intended for use outside of computer room and provided with such instructions 1 1 2 Equipment in wire line communication facilities Class Il equipment N serving high voltage electric power stations operating at greater than 1kV are excluded 1 1 2 Equipment intended for outdoor use Not outdoor use equipment N 1 4 14 For Pluggable Equipment Type A the protection in Class Il equipment N the installation is assumed to be 20 A 1 5 1 All IEC standards for components identified in Critical components are IEC P Annex P 1 replaced by the relevant requirements of certified See list of critical UL component standards in Annex P 1 components in main CB report 1 5 1 There may be additional requirements for components in USA 1 5 1 All IEC standards for components identified in Critical components are IEC P Annex P 2 alternatively satisfied by the relevant certified See list of critical requirements of UL component standards components in main CB report 1 5 1 There may be additional requirements for components in USA 1 5 5 Interconnecting cables acceptable for the No external interconnecting N application regarding voltage current temperature flexible flammability mechanical serviceability and the like 1 5 5 For oth
51. age V N S ee secondary circuits GI H HH HT Bra eapo HHT B73 Atemelvetestpoceiuve JH B74 Electric strength test test voltage V PN DREES DREES B10 _ Testiorseresmowrs LR re te tee No transformer in the equipment C 2 ANNEX D MEASURING INSTRUMENTS FOR TOUCH CURRENT TESTS see 5 1 4 D 1 Measuring instrument Class III equipment D 2 Alternative measuring instrument Po ANNEX E TEMPERATURE RISE OF A WINDING see 1 4 13 ANNEX F MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES see 2 10 and Annex G ANNEX G ALTERNATIVE METHOD FOR DETERMINING MINIMUM CLEARANCES TRF No IEC60950_1C AIR N Nemko Page 32 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark zi m LN eit fema LN G 1 2 Summary of the procedure for determining BE LI G2 my Ir N S 62 Determination of mains transient voltage V 643 _ Combinaionoftansions T 644 Transients trom cable dstibuion systems w en measurementot wansientvoegs fw o a Transients from a mains supply IN C fomaem LN Jain O OOo o Ta Joy Transen toma tlecommunicatonnewok w Determination of minimum clearances ANNEX H IONIZING RADIATION see 4 3 13 oN K ANNEX K THERMAL CONTROLS see 1 5 3 and 5 3 8 ki Making and breaking capacity Po Temperature limiter endurance operating voltage in TRF No IEC60950_1C N Nemko Page 33 of 46 Report No 175993 www nemko c
52. ard receptacles accessible to the operator with LPS no testing required 5 3 7 Tests interrupted by opening of a component No test interrupted by opening N repeated two additional times of component 5 3 9 1 Test interrupted by opening of wire or trace subject Not applicable N to certain conditions Test results according to last modification date 2007 08 08 in CB Bulletin IEC 60950 1 ed 2 Page 7 of 8 www nemko com Report No 175993 IEC 60950 1 2005 Requirement Test Result Remark 6 Specialized instructions for telephones that may be No TNV circuits N connected to a telecommunications network 6 Marking identifying function of telecommunication No TNV circuits N type connectors not used for connection to a telecommunication network 6 3 Equipment remotely powered over No TNV circuits N telecommunication wiring systems provided with specialized markings adjacent to the connection 6 3 Overcurrent protection incorporated into equipment No TNV circuits N to provide power over telecommunication wiring system not interchangeable with devices of higher ratings if operator replaceable 6 4 Additional requirements for equipment connected to No TNV circuits N a telecommunication network using cable subject to overvoltage from power line failures 6 4 Where 26 AWG line cord required by Fig 6C either No TNV circuits N the cord is provided with the equipment or described in the safety in
53. arthed neutral and more than one phase conductor 1 7 1 Equipment voltage rating not higher than rating of Class Il equipment N the plug except under special conditions 1 7 6 Fuse replacement marking for operator accessible Class Il equipment N fuses 1 7 7 Identification of terminal connection of the Class II equipment N equipment earthing conductor 1 7 7 Connectors and field wiring terminals for external Class II equipment N Class 2 or Class 3 circuits provided with marking indicating minimum Class of wiring to be used 1 7 7 Marking located adjacent to terminals and visible No such terminal used N during wiring 2 1 1 1 Bare TNV conductive parts protected by a cover are No TNV circuits N exempt if instructions include directions for disconnection of TNV prior to removal of the cover 2 3 1 6 Other telecommunication signaling systems than No TNV circuits N described in 2 3 1 b are subject to M 4 2 3 1 6 For TNV 2 and TNV 3 circuits with other than No TNV circuits N ringing signals and with voltages exceeding 42 4 Vp or 60 V d c the max current limit through a resistor 2 2000 Ohm with loads disconnected is 7 1 mA peak or 30 mA d c under normal conditions 2 3 1 0 Limits for measurements across 5000 Ohm resistor No TNV circuits N in the event of a single fault are replaced after 200 ms with the limits of M 3 1 4 2 3 2 1 For a single fault the limits of 2 2 3 apply to SELV No TNV circui
54. as not thicker than the relevant part 4 7 201 4 Testing in the event of non extinguishing material If the parts other than enclosures do not withstand the glow wire tests of 4 7 201 3 by failure to extinguish within 30 s after the removal of the glow wire tip the needle flame test detailed in 4 7 201 3 shall be made on all parts of non metallic material which are within a distance of 50 mm or which are likely to be impinged upon by flame during tests of 4 7 201 3 Parts shielded by a separate barrier which meets the needle flame test need not be tested NOTE 1 If the enclosure does not withstand the glow wire test the equipment is considered to have failed to meet the requirements of Clause 4 7 201 without the need for consequential testing NOTE 2 If other parts do not withstand the glow wire test due to ignition of the tissue paper and if this indicates that burning or glowing particles can fall onto an external surface underneath the equipment the equipment is considered to have failed to meet the requirements of Clause 4 7 201 without the need for consequential testing NOTE 3 Parts likely to be impinged upon by the flame are considered to be those within the envelope of a vertical cylinder having a radius of 10 mm and a height equal to the height of the flame positioned above the point of the material supporting in contact with or in close proximity to connections IEC 60950 1 ed 1 Page 6 of 8 www nemk
55. ation date 2008 07 31 in CB Bulletin IEC 60950 1 ed 2 Page 6 of 7 www nemko com Report No 175993 IEC 60950 1 2005 Requirement Test Result Remark Annex Equipment connected to a telecommunication and No TNV circuits NAD cable distribution networks and supplied with an earphone intended to be held against or in the ear is required to comply with special acoustic pressure requirements Annex Document paper shredders likely to be used ina vor applicable NAF home or home office Pluggable Equipment Type A plug configuration are required to comply with additional requirements including markings instructions protection against inadvertent reactivation of a safety interlock disconnection from the mains supply via provision of an isolating switch and protection against operator access accessibility determined via new accessibility probe amp probe wedge Annex NAF Household home office Document shredders NAF 1 7 Markings and Instructions The equipment is not a shredder NAF 1 7 15 Symbols alerting the user to the following considerations are provided adjacent to the document feed opening These symbols are explained in the instructions Product is not intended for use by children product ISOLA LOW an Avoid touching the document feed opening with HANS uere sean NEN AAA Avoid clothing touching the document feed opening Keep aerosol products away applicable for product KOENEN The A ISO 7000 0434
56. ble to Table 3B delete the words in some countries in condition In NOTE 1 applicable to Table 3B delete the second sentence 3 3 4 In Table 3D delete the fourth line conductor Class III equipment sizes for 10 to 13 A and replace with the following Over 10 up to and including 16 1 5 to 2 5 1 5 to 4 Delete the fifth line conductor sizes for 13 to 16 A c it is permitted for PLUGGABLE EQUIPMENT TYPE B or PERMANENTLY CONNECTED EQUIPMENT to rely on dedicated overcurrent and short circuit protection in the building installation provided that the means of protection e g fuses or circuit breakers is fully specified in the installation instructions If reliance is placed on protection in the building installation the installation instructions shall so state except that for PLUGGABLE EQUIPMENT TYPE A the building installation shall be regarded as providing protection in accordance with the 75993 4 3 13 6 Add the following NOTE The equipment does not NOTE Z1 Attention is drawn to 1999 519 EC Council generate other types of Recommendation on the limitation of exposure of the radiation general public to electromagnetic fields 0 Hz to 300 GHz Standards taking into account this Recommendation which demonstrate compliance with the applicable EU Directive are indicated in the OJEC ON Nemko Page 4 of 12 Report No 175993 www nemko com IEC60950_1A ATTACHMENT Requirement Test Result
57. e test finger remove the parts detachable without a tool Insert the wedge probe Figure JA 2 into the document slot And against all directions of openings if straight cutting type a force of 45 N shall apply to the probe and 90 N if cross cutting type In this case the weight of the probe is to be factored into the overall applied force Before testing with the wedge probe remove the parts detachable without a tool It shall not be possible to touch any hazardous moving parts including the shredding roller or the mechanical section for shedding with the probe Test results according to last modification date 2010 11 27 in CB Bulletin N Nemko Page 11 of 12 Report No 175993 www nemko com IEC 60950 1 2001 Requirement Test Result Remark Dimensions in millimeters 28 Radius Figure JA 1 Test finger Test results according to last modification date 2010 11 27 in CB Bulletin N Nemko www nemko com Page 12 of 12 Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark Diameters in millimeters Diameters in millimeters L N See S Rounded to allow rotation about hinge pin thickness screw in one direction dimensions Details of the tip of wedge Distance from the tip mm Thickness of probe mm 0 2 12 4 180 24 NOTE 1 The thickness of the probe varies linearly with slope changes at the respective points shown in the table NOTE2 The allowab
58. ection against overvoltages is of flammability category FV 0 according to AS NZS 4695 707 or the printed boards are contained in a metal enclosure having openings only for connecting wires which fill the openings completely Compliance shall be determined using the smallest thickness of the material NOTE Available apparent power is the maximum apparent power which can be drawn from the supplying circuit through a resistive load whose value is chosen to maximise the apparent power from more than 2 min when the circuit supplied is disconnected Add the symbol NZ in the right hand margin beside No TNV circuits the first paragraph Aad the following after the first paragraph In Australia this variation does not apply in New Zealand compliance with 6 2 2 shall be checked by the tests of both 6 2 2 1 and 6 2 2 2 Delete the Note IEC 60950 1 ed 1 Page 7 of 8 www nemko com Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark Add the symbol NZ in the right hand margin beside No TNV circuits the first paragraph including Note 1 Delete the Note 2 Aad the following after the first paragraph In Australia this variation does not apply in New Zealand the electrical separation is subjected to 10 impulses of alternating polarity using the impulse test generator of annex N for 10 700us impulses The interval between successive impulses is 60 s and the initial voltage Uc is for
59. ed frequency or aed fequency range Ha DC supple Jaossa o Manufacturers name or trade mark or identification OLPC st ean BS The equipment is regarded as Class Ill The additional marking does not give rise to misunderstandings The user s manual contains information for operation installation servicing transport storage recycling and technical data The operation guide is provided to the user No other special installation instruction required as the equipment is class Ill TRF No IEC60950_1C ON Nemko Page 11 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark 1 7 2 3 Overcurrent protective device Class III equipment GE IT power distribution systems Class III equipment Operator access with a tool All areas containing hazard s are inaccessible to the operator 1 7 2 6 Ozone The equipment not containing Ozone Short duty cycles The equipment is intended for continuous operation _ Supply voltage adjustment No voltage selector No voltage selector selector Methods and means of adjustment reference to installation instructions E Power outlets on the equipment No standard power outlet oN Fuse identification marking special fusing ee ae characteristics cross reference arz wrens lass equipment dN Protective earthing and bonding terminals a a 17 72 Terminals fora mains supply eonaucors iY ON 17 73 Teminalst
60. ended table 2 5 max apparent power VA WE Current rating of overcurrent protective device A No such parts used oN Provisions for earthing and bonding N 2 6 1 Protective earthing 2 6 1 2 6 5 8 Class III E Functional earthing 2 6 3 Protective earthing and protective bonding conductors 2 6 3 2 Size of protective earthing conductors IN a Rated current A cross sectional area mm TRF No IEC60950_1C N Nemko Page 15 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark 2 6 3 3 Size of protective bonding conductors PN Rated current A cross sectional area mm Protective current rating A cross sectional area N D w P Resistance of earthing conductors and their terminations resistance Q voltage drop V test current A duration min N O L oa Colour of insulation 2 6 4 Terminals oN 6 4 Protective earthing and bonding terminals Po Rated current A type nominal thread diameter mm Separation of the protective earthing conductor from protective bonding conductors Integrity of protective earthing a et inerconecton ofequpment ll RS SSES N D P _ N N O O gt gt GA N protective bonding conductors Disconnection of protective earth 2655 _ Parsremovedduingsenicng J O Ton 2 6 5 7 Screws for protective bonding IN 2 6 5 8 Reliance on telecommunication network or cable distribution s
61. er than limited power and TNV circuits the No external interconnecting N type of output circuit identified for output connector flexible 1 5 5 External cable assemblies that exceed 3 05 m in No external interconnecting N length to be types specified in the NEC flexible 1 5 5 Detachable external interconnecting cables 3 05 m No external interconnecting N or less in length and provided with equipment flexible marked to identify the responsible organization and the designation for the cable 1 5 5 Building wiring and cable for use in ducts plenums No such wire used N and other air handling space subject to special requirements and excluded from scope 1 5 5 Telephone line and extension cords and the like No TNV circuits N comply with UL 1863 1 6 1 2 Equipment intended for connection to a d c power Class III equipment N mains distribution system subjected to special circuit classification requirements e g TNV 2 Test results according to last modification date 2007 08 08 in CB Bulletin IEC 60950 1 ed 2 Page 2 of 8 www nemko com Report No 175993 IEC 60950 1 2005 Requirement Test Result Remark 1 6 1 2 Earthing of d c powered equipment provided Class III equipment N 1 7 Lamp replacement information indicated on No lamp provided N lampholder in operator access area 1 7 1 Special marking format for equipment intended for Class III equipment N use on a supply system with an e
62. es gauge used in US 2 7 1 Data for selection of special external branch circuit Class III equipment N overcurrent devices marked on the equipment 2 7 1 Standard supply outlets protected by overcurrent Class Ill equipment N device in accordance with the NEC 2 7 1 Overcurrent protection for individual transformers Class II equipment N that distribute power to other units over branch circuit wiring 2 7 1 Additional requirements for overcurrent protection Class III equipment N apply to equipment provided with panelboards 2 7 1 Non motor operated equipment requiring special Class Ill equipment N overcurrent protective device marked with device rating 2 10 5 12 Multi layer winding wire subject to UL component No multi layer winding wire N wire requirements in addition to 2 10 5 12 and provided Annex U 3 1 1 Permissible combinations of internal wiring external Considered P cable sizes for overcurrent amp short circuit protection 3 1 1 All interconnecting cables protected against Considered P overcurrent and short circuit 3 2 Wiring methods permit connection of equipment to Class Ill equipment N primary power supply in accordance with the NEC 3 2 1 Permitted use for flexible cords and plugs The equipment is not for N connected to a D C mains supply 3 2 1 Flexible cords provided with attachment plug rated The equipment is not for N 125 of equipment current rating connected to a D C mains supply 3 2 1 Any Class II equipment prov
63. est Result Remark Add a new annex JA with the following The equipment is not contents document shredding Annex JA machines normative Document shredding machines Document shredding machines shall also comply with the requirements of this annex except those of STATIONARY EQUIPMENT used by connecting directly to an AC MAINS SUPPLY of three phase 200V or more JA 1 Markings and instructions The symbol Page 9 of 12 Report No 175993 JIS S 0101 2000 6 2 4 and the following precautions for use shall be marked on readily visible part adjacent to document feed opening The marking shall be clearly moia permanent and easily discernible that use by an infants children may cause a hazard of injury etc that a hand can be drawn into the mechanical section for shredding when touching the document slot that clothing can be drawn into the mechanical section for shredding when touching the document slot that hairs can be drawn into the mechanical section for shredding when touching the document slot in case of equipment incorporating a commutator motor that equipment may catch fire or explode by spraying of flammable gas JA 2 Inadvertent reactivation Any safety interlock that can be operated by means of the test finger Figure JA 1 is considered to be likely to cause inadvertent reactivation of the hazard Compliance is checked by inspection and where necessary by a test with the test finger Figure JA 1 JA 3 Disc
64. ff with empty battery 1 84 13 06 pack charging mode Supplementary information 1 Tested with power adapter Bestec NA0241WAA 1 1 7 Measure battery pack connector Maximum normal load supplied by battery pack discharge mode Measure battery pack 2 Tested with power adapter Darfon BBOJ C 3 Tested with power adapter Bestec NAO25SDF xy 2 1 1 5 c1 TABLE max V A VA test N Voltage rated Current rated Voltage max VA max II A Vv A VA Supplementary information 2 1 1 5 c2 TABLE stored energy N Capacitance C uF Voltage U V Energy E J Supplementary information E 0 5 CU x 10 TABLE evaluation of voltage limiting components in SELV circuits N Component measured between max voltage V Voltage Limiting Components normal operation EE Fault test performed on voltage limiting components Voltage measured V in SELV circuits V peak or V d c TRF No IEC60950_1C N Nemko Page 39 of 46 Report No 175993 www nemko com Supplementary information TABLE Limited current circuits Location Voltage Current Freq Vv mA kHz Supplementary information S c Short circuit O c Open circuit TABLE limited power sources P Uoc 5 i S imi Meas Limit USB port CNS 4 96 3 30 100 pin 1 RTN normal pin 2 4 RTN normal USB port CN8 4 96 0 70 1 65 100 pin 1 RTN PL10 s c
65. g N Max output current A Not applicable Current limiting method Not applicable 7 CONNECTION TO CABLE DISTRIBUTION SYSTEMS Protection of cable distribution system service persons and users of other equipment connected to the system from hazardous voltages in the equipment 7 1 General 7 1 7 4 3 Not connected to cable distribution systems TRF No IEC60950_1C ON Nemko Page 29 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark 7 3 Protection of equipment users from overvoltages on the cable distribution system Insulation between primary circuits and cable distribution i 744 4 1 741 General C lt E E mas mses S ON A ANNEX A TESTS FOR RESISTANCE TO HEAT AND FIRE p A 1 Flammability test for fire enclosures of movable Equipment mass lt 18kg equipment having a total mass exceeding 18 kg and of stationary equipment see 4 7 3 2 Test flame see IEC 60695 11 3 Test Se A 1 6 Compliance criteria N Flammability test for fire enclosures of movable All materials have suitable equipment having a total mass not exceeding 18 flame class Glass of LCD kg and for material and components located inside panel are complied with A 2 fire enclosures see 4 7 3 2 and 4 7 3 4 test see below Samples material Type various glass l Wall thickness mm Min 0 34mm thick Conditioning of samples temperature C 70
66. h as follows NOTE 1 See 1 7 5A when Type C 14 appliance coupler rated 10 A per IEC 60320 1 is used with an equipment rated not more than 125 V and rated more than 10 A Replace the first sentence in the third dashed paragraph as follows where no relevant IEC component standard or JIS component standard harmonized with the relevant IEC component standard exists or where components are used in circuits not in accordance with their specified rating the components shall be tested under the conditions occurring in the equipment 1 5 6 In this sub clause add JIS C 5101 14 1998 or No such parts before the reference number IEC 60384 14 1993 In this sub clause add JIS C 5101 14 1998 or No such parts before the reference number IEC 60384 14 1993 5 In the first paragraph add JIS C 5101 14 1998 No such parts or before the reference number IEC 60384 14 1993 Replace the fifth dashed paragraph with the Must be considered when following marketing into Japan manufacturer s or responsible company s name or trade mark or identification mark Test results according to last modification date 2010 11 27 in CB Bulletin N Nemko www nemko com Page 4 of 12 Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark 1 7 5 In the second paragraph add or JIS C No such part 8303 2007 after the reference number IEC TR 60083 1997 1 7 5A Add the following new clause
67. h voltages exceeding 42 4 Vpeak or 60 Vd c the maximum acceptable current through a 2000 ohm resistor or greater connected across the voltage source with other loads disconnected is 7 1 mA peak or 30 mA d c under normal operating conditions 2 3 2 1 In the event of a single fault between TNV and No TNV circuits SELV circuits SELV Circuits and accessible conductive parts comply with the North American limits of 2 2 3 TRF No CSA60950 1 07A bl070423 Test results according to last modification date 2008 07 31 in CB Bulletin IEC 60950 1 ed 2 www nemko com IEC 60950 1 2005 Page 5 of 7 Report No 175993 Requirement Test Result Remark Protective bonding conductors of non standard protective bonding constructions e g printed circuit traces subjected to the additional limited short circuit test conditions specified if required Enclosures around CRTs with a face diameter of 160 mm or more are provided with suitable enclosure to reduce the risk of injury due to the implosion of the CRT Projected area of opening sss eee eee Minor dimension of projected area sss sss eenn E For equipment intended for mounting on racks and provided with slide rails allowing the equipment to slide away from the rack for installation service and maintenance additional construction performance and marking requirements are applicable to determine the adequacy of the slide rails Equipment with handles is required to comply
68. ided with 15 or 20 A Class III equipment N standard supply outlets Edison base lampholders or single pole disconnect device provided with a polarized type attachment plug 3 2 1 2 Equipment intended for connection to DC mains The equipment is not for N supply power systems complies with special wiring connection to a DC mains requirements supply 3 2 1 2 Equipment with one pole of the DC mains supply The equipment is not for N Test results according to last modification date 2007 08 08 in CB Bulletin IEC 60950 1 ed 2 Page 4 of 8 www nemko com Report No 175993 IEC 60950 1 2005 Requirement Test Result Remark connected to both the equipment mains input connection to a DC mains terminal and the main protective earthing terminal supply provided with special instructions and construction provisions for earthing 3 2 1 2 Equipment with means for connecting supply to The equipment is not for N earthing electrode conductor has no switches or connection to a DC mains protective devices between supply connection and supply earthing electrode connection 3 2 1 2 Markings and instructions for equipment with The equipment is not for N provisions to connect earthed conductor of a DC connection to a DC mains supply circuit to the equipment earthing conductor supply 3 2 1 2 Special markings and instructions for equipment The equipment is not for N with earthed conductor of a DC supply circuit connec
69. iffusive type 4 3 13 6 Other types The equipment does not generate other types of radiation 44 Protection against hazardous moving parts 4 4 Protection in operator access areas eee No moving parts 4 4 Protection in restricted access locations l Not intended for installation in Ka RAL Protection in service access areas No moving parts oN as Thermelrequremens LE asi Je TT LE DECHE rr Normal load condition per Annex L sese f Te akc aoe Le a53 Temperature imis tor materas ieee apperdedianea 5 P a54 Touch temperatwe imis Jesse P E 4 5 4 5 5 Resistance to abnormal heat No thermoplastic parts carrying hazardous voltages Openings in enclosures Top and side openings Transportable equipment oN TRF No IEC60950_1C N Nemko Page 25 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark Dimensions mm cnca T mm Bottoms of fire enclosures Transportable equipment oN rr Construction of the bottomm dimensions mm O TT 4 6 3 Doors or covers in fire enclosures The door or cover is intended for occasional use Equipment instructions include directions 46 4 1 Constructional design measures Refer to below Dimensions MM sese e cette ee eee eee eee Top side Numerous circular openings for speakers each max 1 0mm in diameter Left right front rear and bottom sides No opening Fire enclosure construction is
70. imum ambient temperature of 45 C The maximum allowed temperatures are calculated based upon a minimum test temperature of 24 5 C Temp limit is adjusted according to cl 1 4 12 3 If no limit is stated temperature is for reference only Continuously held in normal use TABLE Ball pressure test of thermoplastic parts em Alowed impression diameter mm Is lt 2mm o mm Test Se diameter a mm Gel information TRF No IEC60950_1C N Nemko Page 44 of 46 Report No 175993 www nemko com Enclosure material for top enclosure Enclosure material for all enclosures Supplementary information TABLE touch current measurement Measured between Measured Limit Comments conditions mA mA Supplementary information TABLE Electric strength tests impulse tests and voltage surge tests ON Test voltage applied between Voltage shape Test voltage Breakdow AC DC impulse surge Supplementary information TABLE Fault condition tests rr Ambient temperature C 25 C if nothing else specified ey Power source for EUT Manufacturer model type Refer to general product output rating information for details Speaker Component Fault Test Fuse Fuse Observation No time current A SC 13 5 10 min Unit normal operation except speaker output shutdown no hazard Charger circuit on main board Normal 13 5 Charging current for battery pack 1 68A
71. irements of this standard or with the safety aspects of the relevant JIS component standard or IEC component standards in case there is no applicable JIS component standard is available However in case a component that falls within the scope of the METI Ministerial ordinance No 85 1962 is properly used in accordance with its marked ratings the requirements of 1 5 4 2 8 7 and 3 2 5 apply and in addition a cord connector of power supply cord set matching with an appliance inlet specified in the standard sheets of IEC 60320 1 shall comply with relevant standard sheet of IEC 60320 1 Replace NOTE 1 with the following NOTE 1 AJIS or an IEC component standard is considered relevant only if the component in question clearly falls within its scope Test results according to last modification date 2010 11 27 in CB Bulletin N Nemko www nemko com Page 3 of 12 Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark Replace the first sentence in the first dashed paragraph with the following Considered a component that has been demonstrated to comply with a JIS component standard harmonized with the relevant IEC component standard or where such JIS component standard is not available a component that has been demonstrated to comply with the relevant IEC component standard shall be checked for correct application and use in accordance with its rating Add a NOTE after the first dashed paragrap
72. k CB test report by TUV SUD mfg Shanghai BYD type CL1 CB certificate no SG OF 05784 report ref no 085 110016901 000 TRF No IEC60950_1C N Nemko Page 7 of 46 Report No 175993 www nemko com Test item particulars eee eee eee eee Equipment niels movable hand held x transportable Connection to the maine as snaz gg Ea 2 aya Soz o xte Operating condition ACCESS location EE Over voltage category OVC Mains supply tolerance or absolute mains supply TEE Tested for IT power systems sss ss ssse ess ssss esse ess ss s IT testing phase phase voltage NI Class of equipment Considered current rating A eeeeeeeeeeeteeeeeeeteeeeees Pollution degree PD cccccceeeeeeeeeeeeeeteeeeeneeees ele BEE Altitude during operation M sss sees essere eee Altitude of test laboratory M sse eee eee eee eee eee i Mass of equipment kg esesssssssesssasrsrnssesrnnanrsnneneenss stationary for building in direct plug in pluggable equipment type A type B permanent connection detachable power supply cord non detachable power supply cord x not directly connected to the mains x continuous rated operating resting time x operator accessible restricted access location x OVCI JOVCII JOVCIIl J OVCIV other N A N A N A Class Class Il x Class Ill Not classified N A HPD 1 x PD2 JPD3 IP20
73. le dimensional tolerance of the probe is 0 127 mm Figure JA 2 Wedge probe Test results according to last modification date 2010 11 27 in CB Bulletin
74. lector switch to settings not suitable for operation at 230 VAC Tropical All appliances with tropical test Class III equipment condition test requirements in applicable Standards shall comply with the tropical condition test as stated in the relevant IEC Standards 3 pin mains 145 SS 472 that are registered with the plug Safety Authority Class II a All Class II appliances must be fitted Class III equipment appliances with 2 pin mains plug Appendix W mains plug complied with IEC 83 1975 Standard C5 Version Il or EN 50075 1991 b Class II appliances that are fitted with 3 pin mains plugs must use plugs that are complied with SS 145 and registered with the Safety Authority Appliances rated Electric appliance gt 3 kW must be Class III equipment gt 3 kW or connected to fixed wiring All connection connected to to fixed wiring must be in accordance fixed wiring with Code of Practice CP5 Class All Class appliances must be fitted with Class III equipment appliances 3 pin mains plugs complied with SS Test results according to last modification date 2007 05 29 in CB Bulletin IEC 60950 1 ed 1 www nemko com Detachable power cord set consists of mains plug mains cord and appliance connector Circuit diagrams Circuit diagrams of electronic modules in electrical appliances Controlled goods likely to be treated as toy by children 3 pin AC adaptor 2 pin AC adaptor Detachable
75. mented in Attachment National Differences attached to this test report refer to List of attachments for details Copy of marking plate MODEL No XO 1 5 HS Input 12Vdc 2A em wm The device complies with Part 15 of the FCC Rules Operation Is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC ID HFS CL1B Product of China Quanta Computer Inc MODEL No X0 1 5 HS Input 13 5Vde 2185A O G O The device complies with Part 15 of the FCC Rules Operation Is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference recelved including interference that may cause undesired operation FCC ID HFS CL1B Product of China Quanta Computer Inc TRF No IEC60950_1C N Nemko Page 6 of 46 Report No 175993 www nemko com List of attachments 1 Photos 5 pages 2 European Group Differences and National Differences 12 pages 3 Korean differences 1 page 4 Canadian differences 7 pages 5 US differences 8 pages In addition the following national differences according to IEC 60950 1 2001 6 Australian differences AS NZS 60950 1 2003 8 pages 7 Singapore differences 3 pages 8 Japan differences 12 pages 9 Battery pac
76. n stipulating technical requirements for the Electrical Appliance Delete 1 in Table 3B Add the following note to Table 3D The equipment is regarded as class III equipment no power NOTE For cables other than those complying _ cord used with JIS C 3662 or JIS C 3663 terminals shall be suitable for the size of the intended cables Add the following after the first sentence The equipment is regarded as class III equipment This requirement is not applicable to the external earting terminal of Class 0 equipment Add the following after the first sentence This requirement also applies to those connections in Class 0l equipment where CLEARANCE or CREEPAGE DISTANCES over BASIC INSULATION would be reduced to less than the values specified in 2 10 Replace the first paragraph with the following Must be considered when marketing into Japan Except as permitted below equipment shall be classified and labelled according to JIS C 6802 2005 and JIS C 6803 2006 or IEC 60825 2 2000 as applicable Replace IEC 60825 1 in the second and the last paragraph with JIS C 6802 2005 Test results according to last modification date 2010 11 27 in CB Bulletin N Nemko www nemko com Page 7 of 12 IEC 60950 1 2001 Report No 175993 Requirement Test Result Remark Add the following NOTE to Table 4B 3 NOTE In case no data for the material is available Appendix 4 4 1 b 3 of the Interpretation
77. n of conductors Not applicable Screws for electrical contact pressure No electric screw connection Insulating materials in electrical connections No contact pressure through insulating material 3 1 8 Self tapping and spaced thread screws Thread cutting or space thread screws are not used for electrical connections 3 1 9 Termination of conductors No such device used in equipment TRF No IEC60950_1C N Nemko Page 20 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark Connection to a mains supply 3 2 1 Means of connection 3 2 1 3 2 9 Class III equipment B211 Connectontoanac mainssuppy LN EES B22 Mutple supply connections fa 323 Permanent comected equipment JL Number of conductors diameter of cable and e conduits mm E EE ad Sean ahane B Bza aeres nas LN E ll CS S SS SS PVG chaste wales Deeg Cord anchorages and strain relief WG SS Mass of aaa kg pull EE SS Rated current A cross sectional area mm a Sunywingspawe E m 09 Wiring terminals for connection of external conductors oN Class III equipment 382 __ Connecion ofnon detachable power suply cors LX Bas Scewtemnas TN Bsa Conducorszesiobeconnected LLN TRF No IEC60950_1C ON Nemko Page 21 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark Rated current A cord cable type cross sectional a
78. n the equipment Functional insulation Complies with c 5 3 5 Electromechanical components No electromechanical components in secondary circuits Audio amplifiers in ITE Considered the speaker is adjusted to max volume during the test 5 3 7 Simulation of faults See the enclosed fault condition tests 5 3 8 Unattended equipment No thermostats temperature limiters or thermal cut outs 5 3 9 Compliance criteria for abnormal operating and Refer to below fault conditions TRF No IEC60950_1C ON Nemko Page 28 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark During the tests No fire or molten metal occurred and no deformation of enclosure during the tests 5 3 9 2 After the tests Class III equipment oN e CONNECTION TO TELECOMMUNICATION NETWORKS 6 1 Protection of telecommunication network service persons and users of other equipment connected to the network from hazards in the equipment 6 1 1 Protection from hazardous voltages 6 1 1 6 1 2 2 No TNV circuits Separation of the telecommunication network from BS earth Po Supply voltage V E Current in the test circuit mA 6 1 2 2 Exclusions Protection of equipment users from overvoltages on telecommunication networks oN No TNV circuits e22 Reta ares OOO LH e221 enee H e222 seyss O LH e223 commana f a 6 3 Protection of the telecommunication wiring system from overheatin
79. nection or through other equipment with a connection to protective earthing and to a cable distribution system using coaxial cable may in some circumstances create a fire hazard Connection to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range galvanic isolator see EN 60728 11 NOTE In Norway due to regulation for installations of cable distribution systems and in Sweden a galvanic isolator shall provide electrical insulation below 5 MHZ The insulation shall withstand a dielectric strength of 1 5 kV r m s 50 Hz or 60 Hz for 1 min Translation to Norwegian the Swedish text will also be accepted in Norway Utstyr som er koplet til beskyttelsesjord via nettplugg og eller via annet jordtilkoplet utstyr og er tilkoplet et kabel TV nett kan for rsake brannfare For unng dette skal det ved tilkopling av utstyret til kabel TV nettet installeres en galvanisk isolator mellom utstyret og kabel TV nettet Translation to Swedish Utrustning som r kopplad till skyddsjord via jordat v gguttag och eller via annan utrustning och samtidigt r kopplad till kabel TV n t kan i vissa fall medf ra risk f r brand F r att undvika detta skall vid anslutning av utrustningen till kabel TV n t galvanisk isolator finnas mellan utrustningen och kabel TV n tet Report No 175993 ON Nemko Page 6 of 12 Report No 1759
80. nent or material standard additional requirements for requirements These components include components in Canada attachment plugs battery packs rechargeable type used with transportable equipment cathode ray tubes circuit breakers communication circuit accessories connectors used for current interruption of non LPS circuits cord sets and power supply cords direct plug in equipment enclosures outdoor flexible cords and cables fuses branch circuit fuseholders ground fault current interrupters industrial control equipment insulating tape interconnecting cables lampholders limit controls printed wiring protectors for communications circuits receptacles solid state controls supplementary protectors switches including interlock switches thermal cutoffs thermostats multi layer transformer winding wire transient voltage surge suppressors tubing wire connectors and wire and cables 1 6 1 2 A circuit for connection to the DC Mains Supply is No connect to DC power classified as either a SELV Circuit TNV 2 Circuit or distribution system Hazardous Voltage Circuit depending on the maximum operating voltage of the supply This maximum operating voltage shall include consideration of the battery charging float voltage associated with the intended supply system regardless of the marked power rating of the equipment 2 3 1 For TNV 2 and TNV 3 circuits with other than No TNV circuits ringing signals and wit
81. ng flexible cord and cable assemblies are required to be a suitable cable type e g DP CL2 specified in the CEC NEC essercene For lengths 3 05 m or less external interconnecting flexible cord and cable assemblies that are not types specified in the CEC NEC are required to have special construction features and identification markings Equipment for use on a c mains supply systems with a neutral and more than one phase conductor e g 120 240 V 3 wire require a special marking format for electrical ratings A voltage rating that exceeds an attachment plug cap rating is only permitted if it does not exceed the extreme operating conditions in Table 2 of CAN CSA C22 2 No 235 and if it is part of a range that extends into the Table 2 Normal Operating Conditions Likewise a voltage rating shall not be lower than the specified Normal Operating Conditions unless it is part of a range that extends into the Normal Operating Conditions Wiring terminals intended to supply Class 2 outputs in accordance with CEC Part 1 or NEC shall be marked with the voltage rating and Class 2 or equivalent Marking shall be located adjacent to the terminals and shall be visible during wiring TRF No CSA60950 1 07A b1070423 Considered Class III equipment No external interconnecting flexible cord or cable No external interconnecting flexible cord or cable Class III equipment Class Ill equipment Class III equipment
82. nition 1 2 12 15 add the following Considered 1 2 12 201 POTENTIAL IGNITION SOURCE Possible fault which can start a fire if the open circuit voltage measured across an interruption or faulty contact exceeds a value of 50 V peak a c or d c and the product of the peak value of this voltage and the measured r m s current under normal operating conditions exceeds 15 VA Such a faulty contact or interruption in an electrical connection includes those which may occur in CONDUCTIVE PATTERNS on PRINTED BOARDS NOTE 201 An electronic protection circuit may be used to prevent such a fault from becoming a POTENTIAL IGNITION SOURCE NOTE 202 This definition is from AS NZS 60065 2003 1 1 1 Add the following to the end of first paragraph Critical components are IEC ertified or the relevant Australian New Zealand Standard EES 1 2 5 1 5 2 Add the following to the end of first and third dash Critical components are IEC items certified or the relevant Australian New Zealand Standard 1 3 2 3 Delete Note 2 The equipment is not intended for permanent connection to the mains Test results according to last modification date 2007 05 29 in CB Bulletin IEC 60950 1 ed 1 Page 2 of 8 www nemko com Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark Modify Table 3B as follows Class III equipment Minimum conductor sizes RATED CURRENT OF EQUIPMENT A AWG or kemil cross cross
83. o 9 Chaoyang Road High tech Industrial Park Changshu Economic Development Zone Changshu Jiangsu Province China 6 Tech Com Shanghai Computer Co Ltd No 4 Lane 58 Sanzhuang Road Songjiang Export Processing Zone Shanghai P R China 7 Tech Com Shanghai Computer Co Ltd No 6 Lane 58 Sanzhuang Road Songjiang Export Processing Zone Shanghai P R China 8 Tech Com Shanghai Computer Co Ltd No 7 Lane 58 Sanzhuang Road Songjiang Export Processing Zone Shanghai P R China 9 Tech Giant Shanghai Computer Co Ltd No 68 Rongjiang Road Songjiang Export Processing Zone Shanghai China 10 Tech Front Shanghai Computer Co Ltd No 2 Lane 58 Sanzhuang Road Songjiang Export Processing Zone Shanghai P R China 11 Tech Com Shanghai Computer Co Ltd No 68 Sanzhuang Road Songjiang Export Processing Zone Shanghai P R China TRF No IEC60950_1C N Nemko www nemko com Page 3 of 46 Report No 175993 Testing procedure and testing location GI CB Testing Laboratory Testing location address L Associated CB Laboratory Testing location address Tested by name signature Approved by signature Nemko Taiwan DEI No 409 Section 2 Tiding Blvd Neihu Taipei 114 TAIWAN Vincent Lin Andy Lee Testing procedure TMP Tested by name signature Approved by signature i Testing location address CI Testing procedure
84. o com Page 8 of 12 Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark Replace IEC 60664 1 in NOTE 3 with JIS C The equipment is regarded as 0664 2003 Add the following after the paragraph However the separation requirements and tests of 6 2 1 a b and c do not apply to a CABLE DISTRIBUTION SYSTEM if all of the following apply the circuit under consideration is a TNV 1 CIRCUIT and the common or earthed side of the circuit is connected to the screen of the coaxial cable and to all accessible parts and circuits SELV accessible metal parts and LIMITED CURRENT CIRCUITS if any and the screen of the coaxial cable is intended to be connected to earth in the building installation Replace the second and the third sentence in the first paragraph with the following This distinction between earthed and unearthed floating circuit is not the same as between CLASS EQUIMENT CLASS Ol EQUIPMENT and CLASS II EQUIPMENT Floating circuits can exist in CLASS EQUIPMENT or CLASS 01 EQUIPMENT and earthed circuits in CLASS Il EQUIPMENT class III equipment and not for connected to cable distribution systems The equipment is regarded as class III equipment and not for connected to cable distribution systems Not for connected to TNV circuits Test results according to last modification date 2010 11 27 in CB Bulletin N Nemko www nemko com IEC 60950 1 2001 Requirement T
85. o com Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark 4 7 201 5 Testing of printed boards All materials have suitable flame class no testing The base material of printed boards shall be required subjected to the needle flame test of Clause 4 7 201 3 The flame shall be applied to the edge of the board where the heat sink effect is lowest when the board is positioned as in normal use The flame shall not be applied to an edge consisting of broken perforations unless the edge is less than 3 mm from a POTENTIAL IGNITION SOURCE The test is not carried out if the Printed board does not carry any POTENTIAL IGNITION SOURCE Base material of printed boards on which the available apparent power at a connection exceeds 15 VA operating at a voltage exceeding 50 V and equal or less than 400 V peak a c or d c under normal operating conditions is of flammability category FV 1 or better according to AS NZS 4695 707 or the printed boards are protected by an enclosure meeting the flammability category FV 0 according to AS NZS 4695 707 or made of metal having openings only for connecting wires which fill the openings completely or Base material of printed boards on which the available apparent power at a connection exceeds 15 VA operating at a voltage exceeding 400 V peak a c or d c under normal operating conditions and base material of printed boards supporting spark gaps which provides prot
86. of equipment to the mains Class III equipment supply by a power supply cord is not permitted except for certain equipment such as ATMs 3 2 5 Power supply cords are required to be no longer Class III equipment than 4 5 m in length Flexible power supply cords are required to be compatible with Tables 11 and 12 of the CEC and Article 400 of the NEC 3 2 9 Permanently connected equipment is required to Class III equipment have a suitable wiring compartment and wire bending space 33 Wiring terminals and associated spacings for field Class III equipment wiring connections shall comply with CSA C22 2 No 0 2 33 Wire binding screws are not permitted to attach Class III equipment conductors larger than 10 AWG 5 3 mm2 3 3 4 Terminals for permanent wiring including Class III equipment protective earthing terminals are required to be suitable for Canadian US wire gauge sizes rated 125 percent of the equipment rating and be specially marked when specified 1 7 7 TRF No CSA60950 1 07A b1070423 Test results according to last modification date 2008 07 31 in CB Bulletin IEC 60950 1 ed 2 Page 3 of 7 www nemko com Report No 175993 IEC 60950 1 2005 Requirement Test Result Remark 3 4 2 Motor control devices are required for No AC motors in the cord connected equipment with a motor if the equipment equipment is rated more than 12 A or if the motor has a nominal voltage rating greater than 120 V or is
87. om IEC 60950 1 Clause Requirement Test Result Remark Verdict K 5 Thermal cut out reliability SS K 6 Stability of operation Po ANNEX L NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL ca BUSINESS EQUIPMENT see 1 2 2 1 and 4 5 2 CG base TS ts fewses A LA esckeeeeg H T Ls stressegen TK Le wooro TK 7 ner busnss egupment E E ANNEX CRITERIA FOR TELEPHONE RINGING SIGNALS eee23 N Mi invowucion SS HHT m2 wera S o DEER ERC M 3 1 Ringing signal oN M 3 1 1 Frequency Hz i M 3 1 2 Voltage V M 3 1 3 Cadence time s voltage V M 3 1 4 Single fault current mA M 3 2 Tripping device and monitoring voltage M 3 2 1 Conditions for use of a tripping device or a monitoring voltage M 3 2 3 Monitoring voltage V S ANNEX N IMPULSE TEST GENERATORS see 1 5 7 2 1 5 7 3 2 10 3 9 6 2 2 1 7 3 2 7 4 3 and Clause G 5 N 1 ITU T impulse test generators N 2 IEC 60065 impulse test generator P ANNEX P NORMATIVE REFERENCES TRF No IEC60950_1C N Nemko Page 34 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark ANNEX Q ae EE resistors VDRs see 1 5 9 1 oN ANNEX R EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL PROGRAMMES Minimum separation distances for unpopulated coated printed boards 2 10 6 2 5 ANNEX S PROCEDURE FOR IMPULSE TESTING soe 6223 n si Testequpmen a H EG s2 Exemples of waveforms ving mpusevesing n AN
88. onnection from the mains supply Document shredding machines shall incorporate an isolating switch complying with sub clause 3 4 2 as the device disconnecting the power of hazardous moving parts For this switch two position single use switch or multi position multifunction switch e g slide switch may be used Test results according to last modification date 2010 11 27 in CB Bulletin N Nemko www nemko com IEC 60950 1 2001 Requirement Test Result Remark If two position switch the positions for ON The equipment is not and OFF shall be indicated in accordance document shredding with sub clause 1 7 8 If multi position switch machines the position for OFF shall be indicated in accordance with sub clause 1 7 8 and other positions shall be indicated with proper terms or symbols Page 10 of 12 Report No 175993 Compliance is checked by inspection JA 4 Protection against hazardous moving parts Any warning shall not be used instead of the structure for preventing access to hazardous moving parts Document shredding machines shall comply with the following requirements Insert the test finger Figure JA 1 into all openings in MECHANICAL ENCLOSURES without applying appreciable force It shall not be possible to touch hazardous moving parts with the test finger This consideration applies to all sides of MECHANICAL ENCLOSURES when the equipment is mounted as intended Before testing with th
89. ontains secondary circuits SELV Maximum recommended ambient Tmra 45 C 1 1 2 Additional requirements Exposure to extreme temperatures excessive dust moisture or vibration to flammable gases to corrosive or explosive atmospheres This equipment is intended to operate in a normal environment Offices and homes Electromedical equipment connected to the patient This equipment is not an electromedical equipment intended to be physically connected to a patient Equipment used in vehicles ships or aircrafts in tropical countries or at elevations gt 2000m This equipment is intended to operate in a normal environment Offices and homes TRF No IEC60950_1C ON Nemko Page 9 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark Tann LE Ys TE Comply with IEC 60950 1 or relevant component see appended table 1 5 1 standard 1 5 2 Evaluation and testing of components Certified components are used in accordance with their ratings certifications and they comply with applicable parts of this standard Components not certified are used in accordance with their ratings and they comply with applicable parts of IEC 60950 1 and the relevant component standard Components for which no relevant IEC standard exists have been tested under the conditions occurring in the equipment using applicable parts of IEC 60950 1 EA SS SS ag EC SS SS ECH 1
90. ordec mains supply conductors LH i78 Contlsandindiators i Reerbotow JL Identification location and marking The function of controls affecting safety is obvious without knowledge of language etc 1 7 8 2 Colours For functional indication a LED lights when the equipment is operating 1 7 8 3 Symbols according to IEC 60417 The functional switch is marked dh complies with IEC 60417 5009 1 7 8 4 Markings using figures i No controls affecting safety ON Isolation of multiple power sources Class III equipment oN 1 7 10 Thermostats and other regulating devices S No thermostats or other regulating devices 1 7 11 Durability The marking withstands required tests TRF No IEC60950_1C N Nemko Page 12 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark 1 7 12 Removable parts No marking is placed on removable parts e Replaceable batteries 1 The lithium ion battery cells in the battery pack are not regarded as replaceable Warning text provided in user s manual 2 The lithium type RTC battery is not replaceable Warning text provided in servicing instructions Equipment not intended for installation in RAL PROTECTION FROM HAZARDS p Protection from electric shock and energy hazards oP Protection in operator access areas Refer below p 2 1 1 1 Access to energized parts Energized parts are not accessible Complies Some e Complies
91. rea SD L Zada ean T CR Rated current A type nominal thread diameter Im 3 4 Disconnection from the mains supply Disconnection from the mains supply TN Class Ill equipment 342 osom RRC 343 Permanent comecied equipment w saa Pars which remain energized Jl 345 Tae niare ats LLN 346 Number ot poles single phase and dc eauipmen w 347 Number ot poles eana equpment fw 348 _ Swiches as dsconnestdeviess M f sao Pugsasdisconnectdeviees OOOO o o o o o y f 34 10 Iterconneced equpment LN san Igel LN Interconnection of equipment p 3 5 2 Types of interconnection circuits see eee eee ee Interconnection for SELV circuits only ELV circuits as interconnection circuits No ELV interconnections 3 5 4 Data ports for additional equipment Refer to cl 2 5 4 PHYSICAL REQUIREMENTS ui Stability Angle of 10 The mass of equipment is less than io a Test force N The unit is not The unit is not floor standing TRF No IEC60950_1C N Nemko Page 22 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark Mechanical strength P 4 2 1 General Complies with the requirement also after tests described below are applied Steady force test 10 N No such parts oN 4 2 3 Steady force test 30 N No internal enclosure Steady force test 250 N No hazard The test is performed at all sides of enclosure Impact test Refer below
92. rims knobs and other parts unlikely to be ignited or to propagate flames originating from inside the apparatus or the following a Components that are contained in an enclosure having a flammability category of FV 0 according to AS NZS 4695 707 and having openings only for the connecting wires filling the openings completely and for ventilation not exceeding 1 mm in width regardless of length b The following parts which would contribute negligible fuel to a fire small mechanical parts the mass of which does not exceed 4 g such as mounting parts gears cams belts and bearings small electrical components such as capacitors with a volume not exceeding 1750mm integrated circuits transistors and optocoupler packages if these components are mounted on material of flammability category FV 1 or better according to AS NZS 4695 707 NOTE In considering how to minimize propagation of fire and what small parts are account should be taken of the cumulative effect of small parts adjacent to each other for the possible effect of propagating fire from one part to another Compliance shall be checked by the tests of 4 7 201 2 4 7 201 3 4 7 201 4 and 4 7 201 5 For the base material of printed boards compliance shall be checked by the test of 4 7 201 5 The tests shall be carried out on parts of non metallic material which have been removed from the apparatus When the glow wire test is carried out the part
93. rst and second paragraph of the compliance clause If this insulation is solid including insulation forming part of a component it shall at least consist of either two layers of thin sheet material each of which shall pass the electric strength test below or one layer having a distance through insulation of at least 0 4 mm which shall pass the electric strength test below If this insulation forms part of a semiconductor component e g an optocoupler there is no distance through insulation requirement for the insulation consisting of an insulating compound completely filling the casing so that CLEARANCES and CREEPAGE DISTANCES do not exist if the component passes the electric strength test in accordance with the compliance clause below and in addition passes the tests and inspection criteria of 2 10 11 with an electric strength test of 1 5 kV multiplied by 1 6 the electric strength test of 2 10 10 shall be performed using 1 5 kV and is subject to ROUTINE TESTING for electric strength during manufacturing using a test voltage of 1 5 kV It is permitted to bridge this insulation with a capacitor complying with EN 132400 1994 subclass Y2 A capacitor classified Y3 according to EN 132400 1994 may bridge this insulation under the following conditions the insulation requirements are satisfied by having a capacitor classified Y3 as defined by EN 132400 which in addition to the Y3 testing is tested with
94. rt Form is used by non IECEE members the IECEE IEC logo and the reference to the CB Scheme procedure shall be removed This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02 This Test Report when bearing the Nemko name and logo is only valid when issued by a Nemko laboratory or by a laboratory having special agreement with Nemko N Nemko Page 2 of 46 Report No 175993 www nemko com Test item description seess Laptop Computer OLPC Wade Mai asinine OLPC Manufacturer e See page 1 Model Type reference e XO 1 5 HS Ratings sss sss sss ssss sss sss sees ZA 12Vdce or 1 854 13 5Vde Name and address of production sites Factories 1 Changshu Zhanyun Electronics Co Ltd No 18 Qingdao Road High tech Industrial Park Changshu Economic Development Zone Changshu Jiangsu Province P R China 2 Tech Full Computer Changshu Co Ltd 8 Jinzhou Rd High Tech Industrial Park Changshu Economic Development Zone Changshu Jiangsu 215500 China 3 Tech Full Computer Changshu Co Ltd No 9 Chaoyang Road High tech Industrial Park Changshu Economic Development Zone Changshu Jiangsu Province China 4 Tech Pro Shanghai Computer Co Ltd No 6 Lane 58 Sanzhuang Road Songjiang Export Processing Zone Shanghai P R China 5 Tech Com Shanghai Computer Co Ltd N
95. s class III equipment 1 2 4 3A CLASS 01 EQUIPMENT Equipment having attachment plug without earthing blade where protection against electric shock is achieved by using BASIC INSULATION and providing externally an earth terminal or a lead wire for earthing in order to connect those conductive parts that might assume a HAZARDOUS VOLTAGES in the event of BASIC INSULATION fault to the PROTECTIVE EARTHING CONDUCTOR in the building wiring NOTE Class 0l equipment may have a part constructed with Double Insulation or Reinforced Insulation circuit 1 3 2 Add the following notes after the first paragraph The equipment is regarded as class Ill equipment NOTE 1 Transportable or similar equipment that is relocated frequently for intended usage should not be designed as Class or Class Ol equipment unless it is intended to be installed by service personnel NOTE 2 Considering wiring circumstance in Japan equipment intended to be installed where the provision for earthling connection is unlikely should not be designed as Class or Class 0l equipment unless it is intended to be installed by service personnel Test results according to last modification date 2010 11 27 in CB Bulletin N Nemko www nemko com IEC 60950 1 2001 Requirement Test Result Remark Replace the first paragraph with the following Considered Page 2 of 12 Report No 175993 Where safety is involved components shall comply either with the requ
96. s exceeding 4kV oN ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS p 5 Touch current and protective conductor current 1 5 1 1 General 5 1 1 5 1 7 Class III equipment Configuration of equipment under test EUT 5 1 2 1 Single connection to an a c mains supply N 5 1 2 2 Redundant multiple connections to an a c mains supply 5 1 2 3 Simultaneous multiple connections to an a c mains supply Measured protective conductor current mA f Po Max allowed protective conductor current mA Equipment with touch current exceeding 3 5 mA 5 1 8 Touch currents to telecommunication networks and Not connected to cable distribution systems and from telecommunication networks telecommunication networks nor cable distribution systems TRF No IEC60950_1C ON Nemko Page 27 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark Limitation of the touch current to a telecommunication network or to a cable distribution system Max allowed touch current mA 5 1 8 2 Summation of touch currents from telecommunication networks Electric strength B2 emesen O 5 2 1 General 5 2 1 5 2 2 Class Ill equipment 22 fo ed Test procedure Abnormal operating and fault conditions 5 3 1 Protection against overload and abnormal Class III equipment within operation SELV circuits only No testing considered necessary 5 3 3 Transformers No isolating transformer i
97. s shall be placed in the same orientation as they would be in normal use These tests are not carried out on internal wiring 4 7 201 2 Testing of non metallic materials Parts of non metallic material shall be subject to the glow wire test of AS NZS 60695 2 11 which shall be carried out at 550 C IEC 60950 1 ed 1 Page 4 of 8 www nemko com Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark Parts for which the glow wire test cannot be carried All materials have suitable out such as those made of soft or foamy material flame class no testing shall meet the requirements specified in ISO 9772 required for category FH 3 material The glow wire test shall not be carried out on parts of material classified at least FH 3 according to ISO 9772 provided that the sample tested was not thicker than the relevant part 4 7 201 3 Testing of insulating materials Parts of insulating material supporting POTENTIAL IGNITION SOURCES shall be subject to the glow wire test of AS NZS 60695 2 11 which shall be carried out at 750 C The test shall also be carried out on other parts of insulating material which are within a distance of 3 mm of the connection NOTE Contacts in components such as switch contacts are considered to be connections For parts which withstand the glow wire test but produce a flame other parts above the connection within the envelope of a vertical cylinder having a diameter of 2
98. structions 7 Equipment associated with the cable distribution No Cable distribution systems N system may need to be subjected to applicable parts of Chapter 8 of the NEC H lonizing radiation measurements made under single The equipment does not N fault conditions according to 21 CFR 1020 produce ionizing radiation M 2 Continuous ringing signals evaluated to Method A No applicable N subjected to special accessibility considerations M 4 Special requirements for message waiting and Not applicable N similar telecommunications signals NAC Equipment for use with a generic secondary Not applicable N protector marked with suitable instructions NAC Equipment marked with suitable instructions if for Not applicable N use with a specific primary or secondary protector NAD Acoustic pressure from an ear piece for short and Not applicable N long duration disturbances NAD Equipment connected to a telecommunication and Not applicable N cable distribution networks and supplied with an earphone intended to be held against or in the ear is required to comply with special acoustic pressure requirements Test results according to last modification date 2007 08 08 in CB Bulletin IEC 60950 1 ed 2 Page 8 of 8 www nemko com Report No 175993 IEC 60950 1 2005 Requirement Test Result Remark NAF Household Home Office Document Shredders N NAF 1 7 Markings and instructions aler
99. t the user to key The equipment is not a N safety considerations related to use of shredders shredder including not intended to be used by children avoid touching document feed opening avoid clothes and hair entanglement and avoid aerosol products NAF 2 8 3 Safety interlock cannot be inadvertently activated by N the articulated accessibility probe NAF 3 4 Provided with an isolating switch complying with N 3 4 2 including 3 mm contact gap with appropriate markings associated with the switch NAF 4 4 Hazardous moving parts are not accessible as N determined using the articulated accessibility probe and the accessibility probe wedge Test results according to last modification date 2007 08 08 in CB Bulletin IEC 60950 1 ed 1 Page 1 of 8 www nemko com Report No 175993 IEC 60950 1 2001 Requirement Test Result Remark National Differences for AUSTRALIA NEW ZEALAND P ZZ 1 Introduction This Annex sets out variations between this Standard and IEC 60950 1 2001 These variations indicate national variations for purposes of the IECEE CB Scheme and will be published in the IECEE CB Bulletin These variations are indicated within the body of the Standard ZZ 2 Variations The variations are as follows 2 Between the definitions for Person service and Considered Range rated frequency insert the following POTENTIAL IGNITION SOURCE 1 2 12 201 2 12 15 After the defi
100. tain more than 0 76 m of combustible media combustible area greater than requires provision for automatic sprinklers or a 0 76 m gaseous agent extinguishing system 4 7 3 1 Equipment for use in environmental air space other Equipment not used in N than ducts or plenums provided with metal environmental air space enclosure or with non metallic enclosure having adequate fire resistance and low smoke producing characteristics according to UL 2043 Equipment for installation in space used for environmental air described in Sec 300 22 c of the NEC provided with instructions indicating suitability for installation 4 7 3 1 Flame spread rating for external surface of The equipment has neither N combustible material with exposed area greater combustible area greater than than 0 9 m or a single dimension greater than 1 8 0 9m nora single dimension m 50 or less for computer room applications or 200 greater than 1 8 m or less for other applications 4 7 3 4 Wire marked VW 1 or FT 1 considered Considered P equivalent 5 1 8 2 Special earthing provisions and instructions for Not connected to a N equipment with high touch current due to telecommunication network telecommunication network connections 5 1 8 3 Touch current due to ringing voltage for equipment Not connected to a N containing telecommunication network leads telecommunication network 5 3 7 Overloading of SELV connectors and printed wiring The SELV connectors comply P bo
101. the test of 12 17 is performed at not less than 125 C Where the metal earth pin is replaced by an Insulated Shutter Opening Device ISOD the requirements of clauses 22 2 and 23 also apply ON Nemko Page 9 of 12 Report No 175993 www nemko com IEC60950_1A ATTACHMENT Requirement Test Result Remark In Ireland DIRECT PLUG IN EQUIPMENT is Class IIl equipment known as plug similar devices Such devices shall comply with Statutory Instrument 526 1997 National Standards Authority of Ireland Section 28 Electrical plugs plug similar devices and sockets for domestic use Regulations 1997 In Finland Norway and Sweden TOUCH Class III equipment CURRENT measurement results exceeding 3 5 mA r m s are permitted only for the following equipment e STATIONARY PLUGGABLE EQUIPMENT TYPE A that o is intended to be used in a RESTRICTED ACCESS LOCATION where equipotential bonding has been applied for example in a telecommunication centre and o has provision for a permanently connected PROTECTIVE EARTHING CONDUCTOR and o is provided with instructions for the installation of that conductor by a SERVICE PERSON e STATIONARY PLUGGABLE EQUIPMENT TYPE B e STATIONARY PERMANENTLY CONNECTED EQUIPMENT ON Nemko Page 10 of 12 Report No 175993 www nemko com IEC60950_1A ATTACHMENT Requirement Test Result Remark In Finland Norway and Sweden add the No TNV circuits following text between the fi
102. tion to a DC mains connected to the equipment earthing conductor supply 3 2 1 2 Terminals and leads provided for permanent The equipment is not for N connection of DC powered equipment to supply connection to a DC mains marked to indicate polarity if reverse polarity may supply result in a hazard 3 2 3 Permanently connected equipment has provision for Class Il equipment N connecting and securing a field wiring system i e conduit or leads etc per the NEC 3 2 3 Permanently connected equipment may have Class Il equipment N terminals or leads not smaller than No 18 AWG 0 82 mm and not less than 150 mm in length for connection of field installed wiring 3 2 3 If supply wires exceed 60 C marking indicates use Class Ill equipment N of 75 C or 90 C wiring for supply connection as appropriate 3 2 3 Equipment compatible with suitable trade sizes of Class III equipment N conduits and cables 3 2 5 Length of power supply cord limited to between 1 5 Class Il equipment N and 4 5 m unless shorter length used when intended for a special installation 3 2 5 Conductors in power supply cords sized per NEC Class III equipment N 3 2 5 Power supply cords and cord sets incorporate Class Ill equipment N flexible cords suitable for the particular application 3 2 6 Strain relief provided for non detachable Class II equipment N interconnecting cables not supplied by a limited power source
103. tional requirements for the insulation see 6 1 2 1 and 6 1 2 2 of this annex In Switzerland supply cords of equipment having Class Il equipment a RATED CURRENT not exceeding 10 A shall be provided with a plug complying with SEV 1011 or IEC 60884 1 and one of the following dimension sheets SEV 6532 2 1991 Plug Type 15 3P N PE 250 400 V 10 A ON Nemko Page 7 of 12 Report No 175993 www nemko com IEC60950_1A ATTACHMENT Requirement Test Result Remark SEV 6533 2 1991 Plug Type 11 250 V 10A SEV 6534 2 1991 Plug Type 12 L N PE 250 V 10A In general EN 60309 applies for plugs for currents exceeding 10 A However a 16 A plug and socket outlet system is being introduced in Switzerland the plugs of which are according to the following dimension sheets published in February 1998 SEV 5932 2 1998 Plug Type 25 3L N PE 230 400 V 16A SEV 5933 2 1998 Plug Type 21 L N 250 V 16A SEV 5934 2 1998 Plug Type 23 L N PE 250 V 16A In Denmark supply cords of single phase Class III equipment equipment having a rated current not exceeding13 A shall be provided with a plug according to the Heavy Current Regulations Section 107 2 D1 CLASS EQUIPMENT provided with socket outlets with earth contacts or which are intended to be used in locations where protection against indirect contact is required according to the wiring rules shall be provided with a plug in accordance with standard sheet DK 2 1a or D
104. ts N circuits and accessible conductive parts 2 3 2 4 Enamel coating on signal transformer winding wire No TNV circuits N allowed as an alternative to Basic insulation in specific telecommunication applications if subject to special construction requirements and testing 2 5 Overcurrent protection device required for Class 2 No such component provided N and Class 3 limiting according to the NEC or for a Limited Power Source not interchangeable with devices of higher ratings if operator replaceable 2 6 Equipment having receptacles for output a c power Class III equipment N connectors generated from an internal separately derived source have the earthed grounded circuit conductor suitably bonded to earth Test results according to last modification date 2007 08 08 in CB Bulletin IEC 60950 1 ed 2 Page 3 of 8 ON Nemko www nemko com Report No 175993 IEC 60950 1 2005 Requirement Test Result Remark 2 6 3 3 For Pluggable Equipment Type A Ta b orc are Class Il equipment N not applicable the current rating of the circuit is taken as 20A 2 6 3 4 Capacity of connection between earthing terminal Class Ill equipment N and parts required to be earthed subject to special conditions based on the current rating of the circuit 2 6 4 1 Field wiring terminals for earthing conductors Class Ill equipment N suitable for wire siz
105. ttery Considered refer to separated battery pack CB test report and appended table 4 3 8 and 5 3 Unintentional charging of a non rechargeable No such battery used battery Reverse charging of a rechargeable battery Special shape connector provided for prevent reverse polarity or reverse charging Excessive discharging rate for any battery Considered refer to separated battery pack CB test report 4 3 9 Oil and grease Insulation is not exposed to oil grease etc Dust powders liquids and gases The batteries are considered not to contain flammable liquids or gases 4 3 11 Containers for liquids or gases No containers for liquids or gases in the equipment Flammable liquids The equipment does not contain flammable liquid Quantity of liquid I a TT generate ionizing radiation TRF No IEC60950_1C n n LA LA A a N CH ON Nemko Page 24 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark Measured radiation pA kg Measured high voltage kV Measured focus voltage kV o We E P CRT markings 4 3 13 3 Effect of ultraviolet UV radiation on materials The equipment does not produce significant UV Part property retention after test flammability classification radiation 4 3 13 4 Human exposure to ultraviolet UV radiation The equipment does not produce significant UV radiation 4 3 13 5 Laser including LEDs No laser and LEDs are d
106. ur equipment or readymade consumer product are to be followed a manual in German language has to be delivered when placing the product on the market Of this requirement rules for use even only by SERVICE PERSONS are not exempted Denmark Heavy Current Regulations Class III equipment With the exception of CLASS Il EQUIPMENT provided with a socket outlet in accordance with the Heavy Current Regulations Section 107 2 D1 Standard Sheet DK 1 4a CLASS II EQUIPMENT shall not be fitted with socket outlets for providing power to other equipment Switzerland Ordinance on chemical hazardous Considered risk reduction SR 814 81 Annex 2 15 Batteries Annex 2 15 of SR 814 81 applies for batteries Denmark Heavy Current Regulations Chapter Class III equipment 707 clause 707 4 TOUCH CURRENT measurement results exceeding 3 5 mA r m s are permitted only for PERMANENTLY CONNECTED EQUIPMENT and PLUGGABLE EQUIPMENT TYPE B IEC 60950 1 ed 2 Page 1 of 1 www nemko com Report No 175993 IEC 60950 1 2005 Requirement Test Result Remark National Differences for Korea N Addition Plugs for the connection of the apparatus to the supply mains shall comply with the Korean requirement KSC 8305 and 8305 Class III equipment Addition Must be considered before EMC marketed in Korea The apparatus shall comply with the relevant CISPR standards Test results according to last modification date 2007 05
107. ystem Overcurrent and earth fault protection in primary circuits oN 2 7 1 Basic requirements 2 7 1 2 7 6 Class Ill equipment Instructions when protection relies on building installation Number and location of protective devices S IN Protection by several devices oN TRF No IEC60950_1C N Nemko Page 16 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark Warning to service Dersonnel e ee Safety interlocks zs sym o LR No safety interlock provided Eee A HT zas maneretan LN zsa Fasen o CO 285 woms OOOO S 288 lomo ll 287 Switches andreas ooo f 2872 lomas O o HT az lewes OOOO o HT 274 leemes O o EE EECHER Electrical insulation oN Class III equipment 222 mee LR rr Relative humidity temperature C sese O SCH EELER O f o A Method s use Clearances creepage distances and distances through insulation oN 2 10 1 General 2 10 1 2 10 10 Class III equipment Frequency E Pollution degrees E N 7210 13 Reduced values fortunctonalinsuation n 7210 14 intervening unconnected condusive pars fwn 2410 15 Insulation wth varying dimensions fwn Special separation requirements PN TRF No IEC60950_1C N Nemko Page 17 of 46 Report No 175993 www nemko com IEC 60950 1 Requirement Test Result Remark 240 17 Insulation in crouts generating staring puses

Download Pdf Manuals

Related Search

www.nemko.com www.nemko.com www.nemo.com

Related Contents

Cobra Electronics ESD6060 Operating Instructions    METRAHIT EXTRA ETECH ESPECIAL EBASE - GMC  Eldy 2.3 User`s Manual September 24, 2010  Stoves S5-E900MF  ー電源部の取イ寸方法 ープースター(増幅部)の取イ寸方法  フラトップ Zero の 進化形  HP Stroller 11690A User's Manual  Safety, Operation & Maintenance Manual Manual de  Owner`s Manual - Roadmaster Inc.  

Copyright © All rights reserved. Failed to retrieve file