SMART Sensor 5DPI 19fe
Contents
1. luminaires we recommend that the sensor should be located centrally in the luminaire e Sensor wires must be routed separately from the lamp wires and mains cables otherwise the lighting control system may malfunction If separate routing is not possible for reasons of space shielded lamp wires and mains cables must be used e Application wiring and functionality see separate user manual smartSENSOR 13 25 0 10 2g variant 1 S o gt E drilling hole for IR Receiver oe 1 5 010 5 oe variant 2 E D b Q drilling hole for IR Receiver Note By the installation is to be paid attention to the fact that the IR sensor and the light sensor is visible www tridonic com luxCONTROL lighting control system SMART sensors A corridorFUNCTION with integrated motion sensor soft start of PCA EXCEL one4all is followed by activation of motion detection and constant light control B corridorFUNCTION with external motion sensor The corridorFUNCTION is activated when a standard motion sensor is connected to the central interface D1 D2 If movement is detected by the motion sensor the PCA EXCEL one4all ballasts switch on if no movement is detected they switch to the absence value after the delay time on the motion sensor Only the presence value is constant light controlled For the corridorFUNCTION profile there will be used the profile o2. switch off delay may have different values or may not be defined Absence value The luminous intensity when there is no person present Presence value The luminous intensity when persons are present Dead time Manual off If the system is switched off manually via the switch or REMOTECONTROL IR6 the motion sensor is deactivated At the end of a delay time if motion has not been detected the motion sensor is activated again If the sensor detects motion during the Manual off delay the time will be reset to the start www tridonic com 7 General settings luxCONTROL lighting control system SMART sensors Parameter Default Values Motion Detector enabled on off Light Regulation enabled setpoint Light Regulation 500 Ix Bright out timeout 0 min Bright out threshold 150 Switch On Value auto calculated Default Parameter Motion Detector Parameter Default Values Adjustable range 1 Fade in time lt 0 78S A Presence value controlled Absence value to 100 2 Run on time 20 min 10 s to 42 4 min 3 Fade time 32 S 0 90 5 s B Absence value 10 0 to presence value 4 Switch off delay never off 1 min 30 min O s to 42 3 min never off 5 Fade off time lt 0 7S Manual off 20 min 3 s to 42 5 min Light Data sheet 10 15 C0012 13 Subject to change without notice www tridonic com
3. 20m 4 00m 8 30m d 4 50m 9 30m 5 00m 10 40m The recommended maximum room height for office appli cations is 3m and for corridor applications for example 4m Calculation of the diameter d 2 x tan 0 5 x a x h The following operating modes can be set for the motion detector via the masterCONFIGURATOR configuration software version 2 02 or higher Active The light is switched on or off automatically depending on whether or not there is a person in the room Only Off The motion detector only switches the connected lighting off The luminaires are switched on manually via the con nected external switch or infra red control Never Off If it has not detected any movement the sensor dims to the Absence value parameter and remains at this value Inactive The motion sensor is deactivated The light must be swit ched on or off manually Run on time The time that starts as soon as the presence of a person is no longer detected If the presence of a person is detected again during the run on time the run on time is restarted from Zero If no presence is detected during the run on time the fade time is started as soon as the run on time expires Fade time The time during which the luminous intensity is faded from the presence value to the absence value Switch off delay The time during which the absence value is held before the lighting is switched off Depending on the profile selected the
4. Sensor Extension Cable art no 86459176 PCA EXCEL one4all SMART Interface l l l all PCA EXCEL one4all l l l l i l ie SMART Interface ayn ee eee l optional all SMART Sensor Extension Cable art no 864591 76 PCA EXCEL one4all SMART Interface PCA EXCEL one4all SMART Interface I optional o ee ee 4 cn a i ae me i l ERS h SMART Sensor Extension Cable art no 86459176 PCA EXCEL one4all SMART Interface l l l l l l l PCA EXCEL one4all SMART Interface l l optional L a m l i ee fe a ef Se l l SMART Sensor Extension Cable art no 86459176 luxCONTROL lighting control system SMART sensors Light regulation Precise light measurement via photo diodes 1 50m 0 90m 0 22m 2 00m 1 20m 0 30m 2 50m 1 50m 0 37m 3 00m 1 80m 0 45m 3 50m 2 10m 0 52m 4 00m 2 40m 0 60m 4 50m 2 70m 0 67m 5 00m 3 00m 0 75m 1 m 1 094 yd a The sensor detection zone is dimensioned so that the entire work area is cove red and evaluated not just a single point This ensures that false readings are not made as a result of moving objects across the work surface such as white paper which would otherwise lead to a sudden change in the brightness level The absolute value depends on the luminaire used and the reflectance in the room The rate at which the di
5. f the sensor The motion detector integrated in the SMART Sensor is inactive in this mode C Compatibility with the controllers must be checked before a PCA EXCEL one4all with connected SMART Sensor 5DPI is integrated in a DSI or DALI light management system DSI switch ON OFF via DSI command DSI command 0 zero power switch OFF DSI commands gt 0 switch ON ON means activation of the motion detector by sensor DALI Switch ON OFF via DALI commands Control possible via DALI commands For more information see the x tec II documentation Extension via SMART Sensor Extension Cable If DALI is used both ballasts must be in the same group and controlled via group commands D switchDIM PCA EXCEL one4all with switchDIM function can be switched ON OFF by a short key press By dimming up and down with a long press the set point of the light control can be changed temporarily After switching OFF and ON again the previous setted value will be activated again If presence control and switchDIM are used in combination there may be loss of synchronism if several ballasts are connected to the same momentary action switch and the ballasts or the sensors connected to them are large distances apart Data sheet 10 15 CO0012 13 Subject to change without notice www tridonic com PCA EXCEL one4all SMART Interface l l l all l l l PCA EXCEL one4all SMART Interface l optional l all _ l SMART
6. ile Light detection angle Light measurement at luminance Motion detection angle asymmetric the sensor head factory default symmetric SMART Sensor 5DPI 19fe 3217 40 1 000 Ix 500 Ix 92 0 8m 2 SMART Sensor 5DPI 19fe cF n o 31 40 1 000 Ix 500 Ix 92 0 8 m 2 never off SMART Sensor 5DPI 19fe cF 01 31 40 1 000 Ix 500 Ix 92 0 8 m 2 switch off 1 minute SMART Sensor 5DPI 19fe cF 30 31 40 1 000 Ix 500 Ix 92 0 8 m 2 switch off 30 minutes The measured value at the sensor head corresponds to approx 60 to 3000 lux on the surface measured The illuminance is set for a room defined by Tridonic Depending on the actual room reflectance the measured illuminance may deviate from this value The illuminance should therefore be checked in the installation and adjusted if necessary Data sheet 10 15 CO0012 13 Subject to change without notice www tridonic com luxCONTROL lighting control system SMART sensors SMART Sensor T5 Clip Cap Product description e Clip for mounting the sensor directly to the lamp and cover to protect against indirect light Ordering data Type Article number Packaging bag Packaging carton SMART Sensor T5 Clip Cap 86459499 10 pc s 200 pc s SMART Sensor T8 Clip Cap Product description e Clip for mounting the sensor directly to the lamp and cover to protect against indirect light Ordering data Type Article number Packaging bag Packaging carton SMART Senso
7. luxCONTROL lighting control system TRI DON IC SMART sensors OCE SMART Sensor 5DPI 19fe Ambient light sensor and presence detector for lighting control Product description e Optional ambient light sensor and presence detector for PCA EXCEL one4all devices from the x tec Il generation e Can be remote controlled e Compact dimensions for luminaire installation e Simple cable connection to the ballast via SMART interface e Power supply via ballast e Lighting control and presence detection can be deactivated e Individual adjustment of the parameters with configuration software e Optional with corridorFUNCTION profile e Optional connection with second ballast possible via accessory cable e Max installation height 5 m Technical data Power supply via SMART interface Current draw 1 mA from SMART interface Operating temperature 0 60 C Storage temperature 20 65 C Type of protection IP20 Max casing temperature tc 63 C Ordering data Standards page 5 Type Article number Packaging carton Wiring diagrams and installation examples page 6 7 SMART Selisor UE VI 20000344 20 pels SMART Sensor 5DPI 19fe cF n o 28000929 20 pc s SMART Sensor 5DPI 19fe cF 01 28000927 20 pc s SMART Sensor 5DPI 19fe cF 30 28000928 20 pc s Specific technical data Type Detection Max cable length Control output devices corridorFUNCTION prof
8. mming value is changed is dynamically linked to the overall lighting level The following operating modes can be set for lighting control via the masterCONFIGURATOR configuration software version 2 02 or higher Active Constant light control is active Inactive Constant light control is deactivated The lighting switches to a defineable value Permanent change of light control set point The Up Down button on the remote control enables the setpoint value to be changed temporarily Pressing the Set button on the remote control stores the setpoint value permanently The light source indicates that the value has been stored successfully by flashing twice In DALI operation the setpoint can be adjusted also with the masterCONFIGURATOR version 2 02 or higher The DALI RESET command restores the default value set at the factory Bright out If the nominal illuminance e g 500 lux is exceeded by more than 150 e g 750 lux the lighting is switched off even if motion is detected The lighting is switched on again when the measured light value falls below the setpoint This function can be adjusted via the masterCONFIGURATOR version 2 02 or higher Data sheet 10 15 CO0012 13 Subject to change without notice Presence detection Detection area 46 scope 2 5 m presence detection 5m motion detection h d 1 50m 3 10m 2 00m 4 10m 2 50m 5 20m 3 00m 6 20m 3 50m 7
9. r T8 Clip Cap 86459500 10 pc s 200 pc s Data sheet 10 15 CO0012 13 Subject to change without notice www tridonic com Product description e Cover to protect against indirect light Product description e Optional infra red remote control e Switching on and off On Off button e Dimming Up Down button e Activation of automatic lighting control e Setting the threshold control point Set button Data sheet 10 15 CO0012 13 Subject to change without notice luxCONTROL lighting control system SMART sensors SMART Sensor Cap Ordering data Type Article number Packaging bag Packaging carton SMART Sensor Cap 86459501 50 pc s 500 pc s REMOTECONTROL IR6 Ordering data Type Article number Dimensions Lx WxH Packaging carton REMOTECONTROL IR6 28000647 86 5 x 40 5 x 7 2 mm 500 pc s www tridonic com 3 luxCONTROL lighting control system SMART sensors SMART Sensor Extension Cable Product description e Cable for optional connection of the sensor with a second ballast e Only use with SMART Sensor 19fe Ordering Data Type Article number Length Packaging carton SMART Sensor Extension Cable 86459176 0 8m 1 500 pc s SMART Sensor Cover Frame Product description e Cover frame for attaching the sensor directly to the luminaire casing Ordering data Type Article number Packaging bag Packaging carton SMART Mounting Ring 5DPI 86459428 50 pc
10. rs and copiers located in the detection zone may cause incorrect presence detection e To avoid false readings the sensor should be installed so there is no direct light from the lamp in the detection zone Mounting with cams at the sensor housing On the housing of the sensor are fixing cams integrated With this cams the sensor can be mounted directly in the luminaire housing Size of the sheet 0 8 1 2mm Mounting with cover frame in luminair housing SMART Mounting Ring SDPI art no 28000910 size of the sheet 0 8 1 2mm 13 75 oi Data sheet 10 15 CO0012 13 Subject to change without notice With the sensor installed the setpoint value dimming can be temporarily changed by means of DALI or switchDIM set point can be changed and set via REMOTECONTROL IR6 on the sensor The configuration of the sensors is done via masterCONFIGURATOR software tool version 2 02 or higher For further information please refer to the x tec Il documentation Standards EN 61547 EN 61347 1 EN 61347 2 11 EN 55015 e The back side of the sensor should not be exposed to the light output of the lamp as this can negatively influence the operation of the sensor To avoid any malfunction we strongly recommend Use the SMART Sensor cap which can be ordered as accessories or Alternatively Mount the sensor away from light exposure from behind e o avoid false measurements caused by the light from other
11. s 200 pc s Data sheet 10 15 CO012 13 Subject to change without notice www tridonic com luxCONTROL lighting control system SMART sensors SMART Sensor 5DPI 19fe In combination with the PCA EXCEL one4all based on the xitec Il platform SMART Sensor SDPI 19fe provides the basis for an easy to use and cost effec tive lighting system When the sensor detects movement it triggers a predefined motion detection profile in the ballast Constant lighting control acts exclusively on the presence value As the amount of natural ambient light changes the illuminance from the artificial lighting system is adjusted With a SMART Sensor 5DPI 19fe installed PCA EXCEL one4all based on the x tec Il platform can be switched on and off via DSI or DALI signals switchDIM or the mains Installation A e Before connecting disconnecting the sensor to from the SMART interface the power supply has to be switched off e Only for the use of ballasts with x tec II label e The SMART Sensors have to be connected only to the SMART interface of PCA EXCEL one4all based on the xtec Il range e The SMART interface is not SELV The installation instructions for mains voltage therefore apply e Please ensure that the detection range of the sensor lies in the lighting area of the controlled luminaires e Please ensure that the detection ranges of the sensors do not overlap This may have influence to the lighting control e Heaters fans printe
Download Pdf Manuals
Related Search