Scosche NN1669B car kit
Contents
1. codes and information pertaining to installation of this kit NN1669B in 2011 Nissan Quest vehicles Scosche Industries Inc can not be held responsible for discrepancies inconsistencies that may occur due to the automobile manufacturing changes or options or damage that may occur in the automobile during the installation of components while using this booklet If you have any further questions call our toll free technical help line at 1 800 621 3695x3 2011 SCOSCHE INDUSTRIES INC SI NN16698 3000003 7 11 FACTORY STEREO REMOVAL 2011 NISSAN QUEST 1 Open passenger door Using a panel removal tool unclip and remove triangle shaped side dash panel that is exposed when door is open 2 Using a Phillips head screwdriver extract 1 screw that is now exposed securing the large trim bezel above the glove box 3 Using a panel removal tool unclip the trim bezel above glove box starting from passenger side and moving towards the radio and remove 4 Using a panel removal tool unclip and remove both lower center dash side panels 5 Using a panel removal tool extract 4 plastic snap rivets holding the center dash lower front bezel in place First pop center pin up then remove entire rivet Disconnect wiring and remove panel 6 Using a panel removal tool Unclip and remove entire panel underneath steering column 7 Using a panel removal tool remove hazard light trim bezel from left side or shifter Disconnect wiring and rem2. SCOSCHE IN DASH STEREO INSTALLATION KIT FOR 2011 NISSAN QUEST NON NAVIGATION MODELS ONLY NN1669B 2 F neser Z BRACKET 7197 RIGHT BRACKET P o o This premium installation kit is for 2011 Nissan Quest vehicles Included are all the parts you need to mount your car stereo or CD player into your vehicle s dash Refer to the individual instruction in this manual to remove your vehicle s factory radio and assemble the kit CAUTION DISCONNECT YOUR VEHICLE S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION TO HELP PREVENT ELECTRICAL DAMAGE WE RECOMMEND THE USE OF A VOLT OHM METER OVER A TEST LIGHT TO CHECK WIRING A TEST LIGHT OR GROUNDED WIRE PROBE CAN CAUSE DAMAGE TO THE VEHICLE S COMPUTER AND OR DIAGNOSTIC SYSTEMS AVOID ALL FACTORY AIRBAG WIRING AIRBAGS CAN ACCIDENTALLY DEPLOY CAUSING SERIOUS INJURY OR DEATH NOTES See your vehicle s instructions for any special tools your installation might require Read all instructions accompanying your car stereo for proper wiring and mounting instructions FACTORY WI G CODES For Factory Wiring Codes go to WWWw Scosche cars com CAR STEREO CONNECTORS PROVIDE EASY CONNECTION OF YOUR CAR STEREO TO FACTORY WIRING HARNESS NNO4B NAA2B 2007 up Nissan 2007 up Nissan Versa wy 4 J Versa Antenna Adapter LIABILITY DISCLAIMER This instruction booklet is based on carefully documented data and research of automobile dash disassembly wire harness
3. ied a SUPPORTS with aftermarket stereo and bolt secure in place Note If hardware is not supplied with aftermarket stereo reuse hardware from 7408 factory stereo BRACKET 7197 RIGHT BRACKET NOTE REAR SUPPORT AVAILABLE SEPARATELY REAR SUPPORT OF THE STEREO ADDS TO THE INSTALLATION S STRUCTURAL INTEGRITY
4. ove 8 Using a Phillips head screwdriver remove the 4 screws securing the trim around the shifter and HVAC controls and remove 9 Using a Phillips head screwdriver remove the 2 screws securing the bottom portion of bezel surrounding the radio 10 Using a panel removal tool unclip bezel surrounding the radio and remove 11 Using a Phillips head screwdriver remove the 4 screws securing radio to the dash Disconnect wiring and remove MOUNTING THE STEREO DIN ISO MOUNT im 1 Align 7197 right amp 7198 left brackets to appropriate sides of 6796 pocket with the bottom A B amp C slots The front peg of r pocket should rest as far forward a in the slot as possible 7198 2 Secure pocket using supplied Lert screws in the post above the BRACKET markings 3 Align aftermarket single din stereo with top hole pattern of kit Use reference indicator lines A B amp C to match desired alignment on both sides 4 Mount brackets using hardware supplied with aftermarket stereo and bolt secure in place Note If hardware is not supplied with aftermarket stereo reuse hardware from factory stereo 7197 RIGHT BRACKET DOUBLE DIN ISO MOUNT 1 Align 7197 right amp 7198 left brackets to appropriate sides of aftermarket double din stereo Use reference indicator lines A B amp C to match desired alignment on both sides 2 Mount brackets using m VARIOUS REAR hardware suppl
Download Pdf Manuals
Related Search