6160RF - At Knight Watch, Inc
Contents
1. K0903 11 022. BASIS OF LIABILITY WHATSOEVER EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER S OWN NEGLIGENCE OR FAULT Seller does not represent that the products it sells may not be compromised or circumvented that the products will prevent any personal injury or property loss by burglary robbery fire or otherwise or that the products will in all cases provide adequate warning or protection Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary robbery fire or other events occurring without providing an alarm but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING HOWEVER IF SELLER IS HELD LIABLE WHETHER DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN SELLER S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER This warranty replaces any previous warranties and is the only warranty made by Seller on this product No increase or alteration written or verbal of the obligations of this Limited Warranty is authorized ADEMCO GROUP 165 Eileen Way Syosset NY 11791 Copyright 2002 PITTWAY CORPORATION
3. PANEL Figure 2 6160RF Wiring Details Table 1 Wiring Table Keypad Control Panel AG Data Out ee ceux Pwr Red 6 5 Reattach the keypad to the mounted case back Attach the top of the keypad first and then press the bottom section down until it snaps into place securely Peel off protective film on the LED panel and install the keypad labels as required APPLICATION GUIDELINES FOR THE 6160RF Use the following guidelines when planning an installation This is the only transceiver on the system There is another receiver or transceiver on the system Notes You want to use both the receiver and transmitter function on a single partition system You want to use only the transmitter function on a second partition You want to use only the transmitter function on a single partition system e Set the keypad to a device address assigned to the desired partition e Enable the receiver e Program a system House ID in the control panel this will enable the transmitter function Set the wireless devices that will communicate with this 6160RF to the same system House ID e Set the keypad to a device address assigned to the desired partition e Disable the receiver e Program a DIFFERENT House ID in the 6160RF than is programmed in the control panel Set the wireless devices that will communicate with this 6160RF to the same House ID as the 6160RF e Set the keypad to a device
4. address assigned to the Partition 1 e Disable the receiver e Program a House ID in the 6160RF that matches the system House ID programmed in the control panel e Set the wireless devices that will communicate with this 6160RF to the same House ID On Vista 40 panels and above wireless keypads e g 5827BD can only be used on a single partition This partition is programmed in field 1 48 and must match the partition assigned to the 6160RF Wireless keys can be used on more than one partition using a House ID programmed in the 6160RF and the devices In this case the wireless keys must be assigned to the same partition as the 6160RF On Vista 20P panels the 6160RF will use the House ID programmed in the panel for the partition to which it is assigned Wireless keypads can only be used on Partition 1 PROGRAMMING THE 6160RF Refer to the following procedure to program the 6160RF STEP DESCRIPTION DISPLAY CHOICES Enter the program mode by pressing the 1 and 3 keys simultaneously for a few seconds within 60 seconds after applying power 2 Keypad Address Enter the two digit keypad address Press the key to continue Notes 1 Refer to the control panel s installation instructions for the receiver if RF transmitters or wireless keypads are programmed into the CONAGGRESS XX Ord acceptable keypad addresses 2 On the VISTA 40 and above the 6160RF s partition assignment must match the RF keypad part
5. of Pittway Corporation and its divisions subsidiaries and affiliates Seller 165 Eileen Way Syosset New York 11791 warrants its products to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 24 months from the date stamp control on the product or for products not having an Ademco date stamp for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period in which case the shorter period shall apply Seller s obligation shall be limited to repairing or replacing at its option free of charge for materials or labor any product which is proved not in compliance with Seller s specifications or proves defective in materials or workmanship under normal use and service Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Ademco factory service For warranty service return product transportation prepaid to Ademco Factory Service 170 Michael Drive Syosset New York 11791 THERE ARE NO WARRANTIES EXPRESS OR IMPLIED OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED OR UPON ANY OTHER
6. 1 YES Note If you need to disable encrypted devices refer to the Disabling High Security Devices section When operating the system in High Security mode 5804BD wireless keys will still function If you want the system to recognize only encrypted wireless devices program only encrypted devices in the system ACTIVATING HIGH SECURITY DEVICES This following procedure should be followed if using High Security encrypted devices DESCRIPTION Follow the normal procedure for programming the device into the control panel refer to the Installation Instructions for the device that you are programming Exit out of Programming Mode Put the control panel in Go No Go Test mode See the Installation Guide for the panel being installed Follow the instructions supplied with each wireless device to enroll the device in High security mode The 6160RF will momentarily display the serial number of the device DISABLING HIGH SECURITY DEVICES This mode gives you the ability to disable high security on all wireless keys that have been enrolled in the 6160RF This is particularly useful if a user loses a wireless key Once high security encrypted devices have been disabled they will only operate if the 6160RF is set to listen to both e encrypted and non encrypted devices programming step 6 above To completely disable the devices they must be deleted from the control panel DESCRIPTION DISPLAY CHOICES After the keypad has be
7. 3 8 H x 7 3 8 Wx 1 1 4 D eure an son ahd ae 137mm x 187mm x 32mm Sounderon 150mA Wiring Refer to Table 1 Display 2 x 16 alphanumeric supertwist LCD backlit Range 200 ft 60 9 m nominal Sounder Tone Generator Integrated Circuit fire alarm is loud pulsing tone Frequency 345 MHz burglary audible panic alarm is continuous tone FOR DETAILS ON THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL PANEL BEING INSTALLED IN CONJUCTION WITH THIS DEVICE FCC STATEMENT FCC ID CFS8DL6160RF This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation FEDERAL COMMUNICATIONS COMMISSION FCC Part 15 STATEMENT This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User s Manual Unauthorized changes or modifications could void the user s authority to operate the equipment ADEMCO LIMITED WARRANTY Alarm Device Manufacturing Company a Division
8. ADEMCO K0903 11 02 6160RF Keypad Transceiver Installation and Setup Guide GENERAL INFORMATION The 6160RF keypad transceiver is a combination unit that combines the functions of the following devices e 6160 Alphanumeric Addressable K eypad e 5881H RF Receiver e 5800TM Transmitter Module The 6160RF Keypad Transceiver may be used on any control panel that supports 5800 Series wireless devices e g VISTA 10P VISTA 15P VISTA 20P FEATURES e Supports wireless key transmitters e g 5804 and bi directional transmitters e g 5804BD 5827BD e Supports wireless keys with high security encryption capability e g 5804 e Provides a nominal range of 200 for the RF transmitters some transmitters have a shorter range e Supports RF jam detection when the receiver is enabled e Capable of sending status signals Armed Ready etc to bi directional units such as 5804BD 5804BDV and 5827BD UL The following transmitters are not intended for use in UL installations 5804 5804BD 5804BDV 5804E and 5827BD INSTALLING THE 6160RF Locate the 6160RF in an area and at a height where it is convenient for user operation The 6160RF must be at least 10 ft from the control panel to ensure proper operation of the RF receiver Mounting And Wiring The 6160RF has terminal blocks for connection to power and data wires Removing the keypad s case back provides access to the terminal blocks The 6160RF can be surface moun
9. en powered for at least 60 seconds hold down CONADDRESS XX 00 31 the 1 and 8 keys at the same time for 3 seconds The current keypad address will be displayed You cannot change the keypad s address at this point Press the key to continue Delete High Security Devices Press the 1 key to remove all high DISABLE HS DEV 1 YES security encrypted devices Press the key to continue NO 1 9E5 0 NO If YES was selected in Step 2 the unit will display a confirm request to ARE YOU SUREP delete the stored high security device Press the 1 key to accept NO YES followed by the key to exit the programming mode TROUBLESHOOTING The error messages listed in the following table cause the 6160RF to produce a single ding tone The table describes the error messages and the corrective actions Low battery in the wireless key Replace the panel if the wireless key has a replaceable battery ial heme meme a Verify that the keypad DI yellow wire is connected properly control panel terminals is not communicating to the control panel Check 09 1 The control panel does not see the 1a Verify that the keypad DI yellow and DO green wires are connected properly O 100i eels Of ihe MeceWvel 1b Verify that the control s receiver address is correct is not functioning 2 Another device on the keypad 2 Verify the wiring connections between the control and all other devices SPECIFICATIONS Physical 5
10. ition assignment programmed in field 1 48 RECEIVER ON 0 OFF control and no other receivers are enabled Press the key to continue 1 Receiver Enable Enter 1 to enable or 0 to disable Receiver Enable the DESCRIPTION DISPLAY CHOICES Receiver Address If receiver is enabled enter the two digit receiver PEC ADDRESS XX 00 30 address 01 30 Note Refer to the control panel s installation instructions for the acceptable receiver addresses Press the key to continue House ID This prompt will only appear if the receiver is disabled If the HOUSE ID XX receiver is enabled the 6160RF will use the House ID programmed in the panel Refer to the Application Guidelines on the previous page when selecting a House ID To program a House ID Enter 01 31 To disable the transmitter Enter 00 Note All devices that you want to receive status from the 6160RF must be set to the same House ID as the 6160RF refer to Table on Page 1 Press the key to continue Enable High Security Mode Enter 1 to select High Security Mode HIGH SECURITY 1 Enable Note If this mode is enabled the 6160RF will only recognize encrypted GFF f ON 0 Disable devices If this mode is disabled the 6160RF will recognize both encrypted and non encrypted devices Press the key to continue Disable High Security Devices Press the key to skip this prompt and DISABLE HS DEVP exit Program Mode NDO
11. ted directly to walls or toa single or double gang electrical box Follow these steps to mount and wire the keypad 1 Detach the case back by pushing up into one of the two slots at the bottom of the keypad with the blade of a small screwdriver this will push in the release snap then pull that side of the case back away Repeat for the other side Refer to Figure 1 for location of the case back release snaps NOTE TO REMOVE REAR COVER PUSH IN THE TWO MOUNTING SNAPS LOCATED ALONG THE BOTTOM OF THE KEYPAD AND LIFT COVER UP 6164RF 003 V0 MOUNTING RELEASE SNAPS Figure 1 Removing the Case Back 2 Pass the wiring from the control panel through the opening in the case back see the control panel s instructions for proper run lengths a If surface wiring is being used wiring may be routed through the top or the bottom left side breakout in the case back The breakouts must be punched out using a screwdriver before mounting the case back b If desired wires may be strain relieved to the wire tie point on the inside of the case back with a tie wrap not supplied 3 Mount the case back to a wall or to an electrical box using the 25mm long self tapping screws supplied mollies for drywall are not supplied 4 Connect the power and data wires from the control panel to the terminals on the 6160RF as indicated in Figure 2 and Table 1 OOO000000 WIRING TERMINALS TO CONTROL
Download Pdf Manuals
Related Search