JetTimer User Manual
Contents
1. 1 Jet Nr 2 0N OFF 1 Jet Nr 2 Time 3 0N OFF 4 6 Pro ES 9 LL en JetTimer User Manual Manually acoustical signal ais 1 To give your client an acoustical signal you have to switch on the remote zeit control by pressing the ON button for 3 sec Choose the number of PWC for example 1 press BUZZ and then ON The client gets a ae ee beep for 2 5 seconds 2 3 Ne 4 5 6 7 8 9 fa s Mom Timer 2 To give a PWC a rental time countdown start the remotecontrol by SS pressing ON for 3 sec Choose the number of the PWC for example 7 directly followed by the rental time for example 10 minutes the 2 display will show JetTimer gt JET No 7 BOD PER gt Time 10 WM Jet Nr 2 Time 3 0N OFF PRO and then press ON On the display will appear sending The receiver ALL is getting the signal 3 Under the number of the PWC in our case number 7 you can see the remaining time on the display of the remotecontrol It will count down NS till O When the time is over the client is getting several beeps to tell him the time is over It will beep in a2. appears sending As long as you see this the remote te BE control gives several signals to make sure the receiver gets it After the 5 Le Pre receiver got the signal the engine of the PWC will be switched off and 7 8 9 ALL ie E locked Under the number of the PWC in the display of the remotecontrol appears an X This means the boat is switched off the client cannot restart it The starter of the engine is not turning even if the client pushes the Start button ETES 2 To unlock the PWC you have to switch on the remotecontrol by pressing ON for 3 seconds after that press the number of the PWC and ON It RENE will appear sending After you unlocked the client can restart the PWC nm with the Start button on the PWC a ts s Pro MO Under the number of the PWC will appear an O which means the boat is on or unlocked 3 With the button ALL you can switch off or on all PWC s at one time U 3 JetTimer JetTimer 1 Jet Nr 2 0N OFF 1 Jet Nr 2 0N OFF 1 Jet Nr 2 Time 3 0N OFF 1 Jet Nr 2 Time 3 0N OFF 1 2 3 u 2 3 pvz 4 5 6 4 5 6 nd 8 9 7 8 9 o 1 a L lt gt 4 4 If you type the wrong number just press DEL to delete JetTimer
3. JetTimer User Manual WORLDWIDE JetTimer 888 EEE 72 ME 2 aaa lan NS www jet timer com JetTimer User Manual Introduction Jet Timer is a development for watersport stations which need to have control over the personal water crafts during the rental time With Jet Timer you have the opportunity to stop the PWC s on the water by remotecontrol You can give manually acoustical signals to your clients and you have also the possibility to start a time countdown between 1 and 99 minutes when the clients start the rental time After the countdown has ended your client will get an acoustical signal which tells him the rental time is over The display of the remotecontrol shows you the remaining rental time of each PWC With one remotecontrol you can control maximum 9 PWC s Each receiver is free programmable between the numbers 1 through 9 Remotecontrol and receiver are working bidirectional which means that they are communicating together So you are at all times informed about the current status of the PWC s With an access code you have the possibility to see the total runtime of each PWC a reset is possible JetTimer User Manual First Steps Follow the installation manual for the receivers and install the wire harness to connect the receiver to the PWC At this time do not fix the receiver to the gastank cause you have to programm the number of the PWC to the receiver as s
4. With button 2 you can adjust the Contrast of the display Inside this menu you can change the contrast with the buttons 4 and 6 and save the adjustment with ON With button 3 you can change the Query Status This is the bidirectio nal control If you switch this off it s saving battery power but you cannot see the rentaltime countdown and the status of the PWC s under the num bers on the remotecontrol display Leave the PROG menu by pressing DEL Battery change on remote control The display shows the charging condition of the batteries Change the batteries only in closed rooms never on the beach The salty humidity can damage the sensitive electronic inside 2 x R6 1 5 Volt JetTimer User Manual Thomas Porda e K Wiesenstr 11 D 64319 Pfungstadt Germany Tel 49 0 6157 850096 Fax 49 0 6157 850097 E Mail info jet timer com www jet timer com
5. oon as it is connected to power After you installed the receiver the PWC is in the OFF mode so you cannot start the engine 1 To programm the receiver PWC number hold the enclosed magnet directly over the black line on the receiver Switch on the remotecontrol by pressing the ON button for three seconds 2 Choose the number on the remotecontrol you want to programm for example 1 after that press immediately ON Now the PWC is programmed as boat number 1 3 Press now 1 and then ON The PWC is switched on you can start the engine al 2 3 JetTimer JetTimer 1 Jet Nr ZON OFF 1 Jet Nr 2 0N OFF 1 Jet Nr ZON OFF 1 Jet Nr 2 Time 3 0N OFF Jej Nr 2 Time 3 ON OFF Jej Nr 2 Time 3 0N OFF 1 2 3 bez r 2 3 u 2 Buzz a 5 6 pro 4 ts 6 Pro alfs Pro 7 8 9 aLi 7 8 9 au 8 ALL XE B pe w o BEE Per o DEL JetTimer User Manual Switch PWC ON OFF 1e 1 To switch off the PWC press ON for three seconds to start the remote STERNEN control After that choose the number of the PWC you want to switch off for example number 1 In the display appears Jet No 1 press OFF SS in the display
6. row and will not stop to beep When the client arrives back you have to switch off the PWC with the remotecontrol and after that you must switch it on again Then the beep will stop 3 JetTimer JetTimer 1 Jet Nr 2 0N OFF 1 Jet Nr 2 ON OFF Jet Nr 2 Time 3 0N OFF LJet Nr 2 Time 3 0N OFF Fae 3 puzz e 3 euzz 5 6 pro 5 6 Pro 7 8 9 ALL 7 8 9 ALL Hi o D De o BEE per Le gt JetTimer User Manual Total Runtime Recall To get the total runtimes of all connected PWC s press O Enter the following code 4228 Now you will see all numbers of connected PWC s with the total runningtimes behind the numbers If a PWC is not in range to send the total time you will see Press ALL to reset the hours Press DEL to leave the menu NOTE If you disconnect the battery from the PWC it will loose the total runtime and starts at O Adjusting Remote Control In this menu you can adjust 3 parameters Press ON for 3 sec to switch on the remotecontrol Press PROG followed by the code 3579 With button 1 you can change the Groupaddress This is important if two watersportstations which are using the Jet Timer are so close together that they could disturb each other If you choose another group address you have to repeat the programming of all receivers with the numbers of the PWC s like described under First Steps at the beginning of this manual
Download Pdf Manuals
Related Search