Home

User`s Manual - akcesoriaPC.pl

1. MONET gt Current Password New Password Confirmed Password _ fram Password Settings u can Change Ihe password of the system required to log into Ihe web management The password car rtan up to 30 t ters and cese sonstive e Parameters Description Current Password Enter your current password for the remote management administrator to login to your server By default the password is 1234 New Password Please enter your new password The password can be 0 to 30 alphanumeric characters and are case sensitive Confirmed Password Enter your new password again for password confirmation Note If you forget your password you have to reset the server to the factory defaults by pressing the Release 1 button longer than 10 seconds Click lt Apply gt at the bottom of the screen to save the above configurations 31 8 3 Network 8 3 1 IP Address Settings You can configure the server to automatically get IP Address from DHCP server or manually specify static IP Address The IP Address of the server must be set to have the same network segment within your network environment or connected computer If the network IP Address settings are incorrect then the server will not be able to communicate throughout the network For example if your router gateway computer is using IP Address 192 168 2 1 then you need to give a unique IP Address to your server with IP range 19
2. Site Survey all the networks nearby will be listed You can select the network you want to connect and click Done 3 http 192 166 2 5 Wireless Site Survey Microsoft Internet Explorer Wireless Site Survey This page provides tool to scan the wireless network If any Access Point or IBSS is found you could choose to connect it manually when client mode is enabled Channel Type ETS 6F_EMAX00 0E 2E FF FF 01 11 Infrastructure off 46 Parameters Description The SSID up to 32 printable ASCII characters is the SSID unique name identified in a WLAN The SSID name of the access points routers stations nearby will be listed here BSSID The MAC ID of the access point router station The radio channel used by the wireless LAN All devices Channel l in the same wireless LAN should use the same channel Display the type of the network If the network is an Type Infrastructure network it will show Infrastructure If the network is an Ad Hoc network it will show Ad Hoc Display the security setting of the network If Off is Encrypt displayed it means that the network is no security settings The signal strength of the network will be displayed Signal e here The higher signal strength the better link quality Sab Click the radio button of the network which you want to elec connect and click Done to connect to the network 39 8 4 2 Secur
3. EPSON Fuji Xerox Fujitsu ES This driver is digitally signed Windows Update Q Have Disk P Tell me why driver signing is important I TT TT 7 Name your printer and setup the default printer click Next Add Printer Wizard Name Your Printer You must assign a name to this printer Type a name for this printer Because some programs do not support printer and server name combinations of more than 31 characters it is best to keep the name as short as possible Printer name EPSON Stylus C61 Series ETEY TT TT 18 8 Choose to print the test page or not lt is recommended to print a test page Click Next Add Printer Wizard Print Test Page To confirm that the printer is installed properly you can print a test page Do you want to print a test page Cas Ue DE tee 9 You have added the printer to the PC successfully The information of the printer is displayed in the windows Click Finish Add Printer Wizard Completing the Add Printer Y Wizard You have successfully completed the Add Printer Wizard You specified the following printer settings Name EPSON Stylus C61 Series Share name lt Not Shared gt Port P5334455 P1 Model EPSON Stylus C61 Series Default Yes Test page Yes To close this wizard click Finish Cancel 10 Now you can start to print from your PC to the print server 19 7 FTP File Server Configuration The serve
4. Add and fill the information of the Add Edit Add Shared Folder page to add a new shared folder for File server Edit Select any shared folder in Shared Folders list and click Edit to modify its setting 72 Parameters Description Click Delete All to delete all the shared folders in Shared Delete All Folders list Delete Click Delete Selected to delete the selected shared Selected folders in Shared Folders list Reset Click Reset to reset selection in Shared Folders list New Storage Default Sharing Policy You can set a default sharing policy Read amp Write Read Only or Not to Share to any USB storage which you don t set any shared folder All users will have the same authority to share all folders in the storage Note1 If you have set shared folders and the user s read write authority the New Storage Default Sharing Policy you set here will not enable Note2 If the storage has NTFS partitions all folders in NTFS partitions are Read Only even you choose Read 8 Write here 73 e Add Edit Shared Folder noo f fie Serer It Server Add Edit Shared Folder EZI alphanumeric and underline Shared folder Brown c Share al folders in Path storage System Users Share Users Add gt gt Admini Add All gt gt Dre Parameters Description Folder Name Define the shared f
5. Mass Storage or Printer to all PCs through Wired or Wireless Network e Compatible with all major operating systems Windows 98SE Me 2000 XP MAC OS and Unix Linux e Easy to configure through the Setup wizard and Web Management tool Print Server e Supports LPR IPP and Raw printing protocols e High compatibility with the popular brands of printers NAS e Share USB Hard Disk or Flash Drive through the network e Support FAT16 FAT 32 Ext2 Ext3 and NTFS Read Only for NTFS file systems e Built in Samba FTP Server e Support account management and user authorization for file folders e Release USB storage through hardware buttons 2 Product Package This package contains the following components WR One Print Server with Storage Server NAS One Dipole Antenna PS 2207SUg only One Power Adapter One Quick Installation Guide One CD ROM Including all the software utilities drivers and User s Manual 3 Hardware Installation Step 1 Connect the server to your LAN network Connect the server to your PC hub or switch by attached the Ethernet cable to the LAN port of the server Step 2 Connect the USB devices to the USB ports of the server You could connect the USB mass storage or printer to any one of two ports for files or printer sharing Note 1 It is recommended to plug the external power to your USB mass storage devices if the USB LED of the connected port is not lit Note 2 Please plug the USB mass stor
6. Server Insiallaton 12 FTP File Server Configuration cooccccccccccccncncncncncnnnos 20 Fei E A a O Lat tale 20 O EE 26 Web Management occcnncnnncnnncninnnnnenininineneneneneninineneneninos 26 Gal US ad doi EOS 29 O O E 30 Ge A A IN 30 8 2 2 Ss EE 31 8 3 NO Ee 32 8 3 1 IP Address Gettmge Aen 32 Ee LEE Ee 34 8 4 TEEN 36 8AT SM SUNY iii 36 8 4 2 SOU 40 ARM NB E E E ere 41 8 4 2 TE A korean tetas slave acer 43 8 4 3 Advanced WEE 45 Ge m AEEA E A A T EE E 48 301 ILPRUPMMUNG a a E E E A atti 50 8 5 1 1 Windows 20001XPI2007 50 851 2 AMADA 56 85 13 AAA CORNER ARAN CRM EE 61 8 5 2 EE ee 65 8 6 FTP File A serch vies 69 Sp NM RE 70 816 2 RIG ONE aaa 72 8 6 3 FIP SO id 76 8 6 4 Storage TOOS ee o o e oe oa s 79 GR EE ill 82 EE Nee EE 8 7 1 Configuration Tools 83 8 7 2 gu TEE 84 NS OSO EE RSE E A e SR EE 85 1 Introduction Thank you for purchasing and using our Print Server with Storage Server NAS product This product provides two USB 2 0 ports User can connect the USB mass storage or printer to each USB port When the USB mass storage is connected the device can be a Storage Server NAS Network Attached Storage allowing user to share files in the storage When the printer is connected the device can be a print server allowing user to share printer through the network Main Features e Comply with IEEE 802 3 IEEE 802 3u Wired Ethernet and IEEE 802 11g b 2 4GHz Wireless LAN standards e Share USB
7. gt at the bottom of the screen to save the above configurations 49 8 5 1 LPR Printing LPR printing protocol is supported in Windows 98SE Me NT 2000 XP 2003 MAC OS 9 x above and Linux Unix The following sections introduce the standard LPR setup process in Windows 2000 XP 2003 MAC OS 9 x and Linux Unix Note It is recommended that running the Print Server Setup Tool in Windows operating system when you want to install the print server Please refer to Chapter 6 8 5 1 1 Windows 2000 XP 2003 To configure the LPR setting in Windows 2000 XP 2003 please follow the steps below 1 Click Start choose Settings and select Printers and Faxes 2 Click Add a Printer 3 The Add Printer Wizard is displayed Click Next Add Printer Wizard Welcome to the Add Printer Wizard This wizard helps you install a printer or make printer connections e If you have a Plug and Play printer that connects 1 through a USB port or any other hot pluggable port such as IEEE 1394 infrared and so on you do not need to use this wizard Click Cancel to close the wizard and then plug the printer s cable into pour computer or point the printer toward your computer s infrared port and turn the printer on Windows will automatically install the printer for you To continue click Next j Cancel 50 4 Select Local Printer attached to this computer and click Next Add Printer Wizar
8. of the server At this mode the server will automatically decide to enable or disable the wireless function When the server starts up it will auto detect if the LAN port is connected to an active network by an Ethernet cable If this is the case the server will run in Ethernet mode If the server is not connected to an active network by Ethernet cable the server will run in wireless LAN mode Users can plug the Ethernet cable to the server at the first after configuring the server features and wireless settings they can unplug the Ethernet cable to enable the wireless connection It makes the configuration much easier without creating the wireless connection in advance Enable Enable wireless function only the server s wireless LAN will be always enabled and Ethernet will be always disabled Disable Disable the wireless function the server s wireless LAN will be always disabled and Ethernet will be always enabled Mode Infrastructure This operation mode requires the presence of an 802 11 Access Point or Router All communication is done via the Access Point or Router Ad Hoc Select this mode if you want to connect to other wireless stations in the Wireless LAN network without through an Access Point or Router Click lt Apply gt at the bottom of the screen to save the above configurations 37 Parameters Description Band 2 4GHz B This server can be compatible with b
9. selection in FTP Folders list Click lt Save gt at the bottom of the screen to save the above configurations 76 Parameters Description Set the maximum concurrent users for the FTP server Max Users f The range is from 1 to 20 Set the time slice for FTP server waits to disconnect a Idle Time FTP client when a FTP client is inactive The available idle time is 1 10 minute s Click lt Save gt at the bottom of the screen to save the above configurations Add Edit FTP Folder Brome Read Ony O Read amp Write Save Reset Cancel Parameters Description Select the user who is authorized to share the folder via FTP Server User Shared Folder s Click Browse to open the explorer window and select Path the shared folder path Click lt Save gt at the bottom of the screen to save the above configurations 77 Parameters Description Here you can assign the read write authority for this Gen shared folder You can select Read Only for read only uthori sharing or select Read Write to give users full access right Click lt Save gt at the bottom of the screen to save the above configurations Note You can not set sharing policy here for folders in NTFS partitions e Browser Shared Folder s Path When you click the Browse button you can see the following pop up window that shows the USB mass s
10. server 11 6 Print Server Installation This server provides a Print Server Setup tool for you to add the network port of the server to your computer automatically After you have added the network port you can run the standard Add Printers procedures in the Windows to install the printer with the print server The program can be performed on Windows 98SE Me 2000 XP 2003 with the same user interface Before installation please confirm that your PC has already connected to the network and installed TCP IP network protocol Please follow the steps below to start installation 1 Insertthe CD shipped along with the server into your CD ROM drive The Autorun exe program should be executed automatically If not run Autorun exe manually from Autorun folder in the CD 2 The following screen will be displayed Click Print Server Utility Print Server and Storage Server NAS Click here to visit www edimax com 3 The PrintServer Utilities window will be displayed Click Next PrintServer Utilities InstallShield Wizard Print Server Utilities Setup Welcome This installation wizard will 1 Copy all necessary utilities and drivers 2 Guide you through the print server setup process 3 Add the print server network print port to your computer 4 Click Next to install the utilities in the default folder or click Browse to specify the destination folder where you would like to ins
11. to enter Storage Name or IP Address of the server User Name for example MS334455 test or 192 168 2 5 test in the User Name field 24 Connect to MS334455 25 7 2 FTP Server To set the USB mass storage or USB Flash Disk as FTP Server for your FTP clients to upload download files from the server please follow the procedures below 1 Open your Web Browser and enter the IP address of the server to logon to the web management of the server The default settings of the server are IP Address 192 168 2 5 User Name admin Password 1234 2 Set the users who are authorized to access to the USB storage device in the Users menu of FTP File Server page O Click Add 0 Enter the user information including User Name and Password Users setup wg klech users tor Fat TP server Users list E CH Agere Data Cortar Add Est L Delete Selected Delete AN Reset Store 26 3 Set the shared folders of the USB storage device which are allowed to access by authorized users in the FTP Server menu of FTP File Server page Please assign the shared folders and the user s read write authority User Select the user who has the right to access the FTP Server Path Designated the shared folder path Read Write Select Read Only or Read Write Note You can not set sharing policy here for folders in NTFS partitions FTP Foldors WC IE Read Witte
12. to prevent further changes 58 5 Enter the Printer Type Printer Address and Queue Name and select the Printer Model to setup the server Click Add to continue Printer Type LPD LPR Printer Address Input the IP Address of the server Queue Name The queue name of the server is Ipt1 or Ipt2 Printer Model Select the Printer Model that is attached to the server Printer Setup Utility Edit View Printers Window Help 088 Printer List O ip Printing E A In Men Printer Type LPD LPR B Printer Address 192 168 1 227 E Complete and valid address Queue Name ptt E Leave blank for default queue Printer Model EPSON FS EPSON Stylus C61 CUPS Gimp Print v4 2 5 EPSON Stylus C62 CUPS Gimp Print v4 2 5 EPSON Stylus C70 CUPS Gimp Print v4 2 5 a EPSON Stylus C80 CUPS Gimp Print v4 2 5 gt Caca GD REN 59 6 The server is installed completely You can see it in the Printer List Printer Setup Utility Edit View Printers Window Help 4 Wed 11 42 PM FE 005 Printer List CH ni OH CH Io Menu j Z LPT1 on 192 168 1 227 EPSON Stylus C61 CUPS Gimp Print v4 2 E PSOOOSER T o Pr Cimp Print v4 2 5 E 5 P5123487_1pt1 EPSON Stylus Color 740 CUPS Gimp Print v4 2 5 Host 7 You can print a file to check whether the server is installed successfully LPT1 on 192 168 1 227
13. traffics by the data categories to provide enhanced multimedia support When the server is connected to the Access Point or Router with WMM function you can enable the function of the server Click lt Apply gt at the bottom of the screen to save the above configurations 47 8 5 Print Server The server supports print server function by default It supports LPR IPP printing protocols These two protocols allow users to connect to printers via TCP IP for printing sharing By using LPR protocol the computer with Windows 98SE Me NT 2000 XP 2003 MAC OS 9 x above and Linux Unix operating systems can use the protocol to share printing in the network By using IPP protocol you can share the printer to all the computers that can access the server by IP Address in Windows 2000 XP 2003 operating systems Print Server The system supports LPR and PP pnrbng methods Vhen you enatle Me pret server Archon please aiso enable Ine IPP or LPR protocol and asugn he printer queue name to each printer connected to the USS port Enable Print Server Print Server Protocol Support EH REH on Print Server Configuration 48 Parameters Description Print Server Features Enable or disable the print server function By default it is enabled IPP When the print server function is enabled the IPP protocol will be enabled as well IPP Internet Printing Protocol Printing provides a convenient way of remote printi
14. 1 pt s go co P zeg E ED MAX R aa Fireware Upgrade Thes too a ows you fo upgrade ihe system s Armste Enter fw path and name of the upgrede file and then cick the APPLY bution below y WHE be prompted to conirm the upgrade This tool wit automatically reboot the system after you have finished the firmware upgrade process if the firmware upgrade process is failed in the next step please do not reboot the system tl you have finished the process 84 8 7 3 Reset If the server stops responding correctly or stop functioning you can perform reset to reboot the server Your settings will not be changed To perform the reset click on the APPLY and you will be asked to confirm the decision Once the reset process is complete you may start using the server again gd Se pan Ppt E s RH kA teats inmenso Rnet Reset In the event that the system stops responding correctly or stops functboning you can pectorm a Reset Your settings wil not be Changed To perform the reset cick on the APFL Y bution below You wil be asked to cor rm your decision R Apoy Cancel Qore orem 85
15. 2 168 2 x Please note Above IP address setting is only an example please do not follow exactly Qro Dy ac y Segcp ana E e An Wo y Sd Mr 1122 148 2 inet x PEJ rm Ouran e EDIMAx Network Settings Set the P Address of the system manualy tor geting IF Address from DHCP Server Thes system also has buin DHCP Server and s able to dispatch he IP address to cher chants IP Address Settings Obtain an IP address automatically Use the following IP address s DHCP Server Domain Name Lease Time 32 Parameters Description Obtain an IP Address Automatically If there is a DHCP Server within your network please select to obtain an IP Address from DHCP Server Then the DHCP server will assign a unique IP Address to your server Use the following If you want to set the server s IP Address manually please select this option You have to enter the IP IP Address Address Subnet Mask and Gateway Address for the Password server Enter the IP Address of the server If your router gateway computer is using IP Address IP Address 192 168 2 1 then you need to give a unique IP Address to your server with IP range 192 168 2 x Subnet Mask Enter the same Subnet Mask as your router gateway computer Enter the same Gateway Address as your Gateway Address router gateway computer This server has a built in DHCP Server please select DHCP Server Enabled to activate the funct
16. 92 168 2 5 Queue Set the queue name to Ipt1 or Ipt2 Name You can designate a name for the printer Location You can enter the location of the printer Printer Select the printer model that is attached to the server Click Add to complete the printer installation 56 e MAC 10 3 x To enable LPR Printing in Macintosh 10 3 x please follow the procedures below 1 In the Desktop click System Preferences System Preferences 2 Click Print amp Fax e a0 System Preferences e Personal E oS e Appearance Desktop Dock Expos International Security Screen Saver Hardware Oy Y Y A CDs DVDs Displays Energy Keyboard amp Sound Saver Mouse Internet Network Mac Network QuickTime Sharing System CO nu a y Accounts Classic Date amp Time Software Speech Startup Disk Universal Update Access 57 3 From the Print 8 Fax screen click Set Up Printers 800 Print amp Fax ges RE E CC Set Up Printers nn Selected printer in Print Dialog Last printer used Default paper size in Page Setup US Letter vi 7 Share my printers with other computers D el Click the lock to prevent further changes 4 Click Add to add the new server through TCP IP 000 Print amp Fax T Printing Faxing Printer List je PSO00888_Ipt1 EPSON Stylus Color PS123487_Iptl EPSON Stylus Color M rr Click the lock
17. B mass storage will be reconnected by the server Please wait a moment till the USB LED for the USB port is turn on again Note 2 If you experience extreme problems or you forgot your password press the Release 1 for longer than 10 seconds and the server will reset itself to the factory default settings warning your original configurations will be replaced with the factory default settings Local Area Network LAN The server s LAN port is where you connect your hubs switches or routers 4 2 Front LEDs On the server s front panel there are LED lights that inform you of the server s current status Below is an explanation of each LED and its description NETWORKING PEOPLE TOGETHER NETWORKING PEOPLE TOGETHER LED Mode Status Description Power On The device is ready Both Green Off No power Off The wireless mode is disabled WLAN Green a The device is trying to connect to the AP or Blinking station On Printing jobs are sending to the printer Print Server E Off No printing jobs On USB mass storage is ready to use e No device is connected USB Status Off e Release is cancelled Green FTP File l e Release is completed Server The Release button is clicked for over 5 Blinking seconds The USB LED is blinking to alert user to unplug the USB mass storage O The LAN cable is connected to the network n UAN device such as hub or switch Both Off No network connection G
18. EDIMAX NETWORKING PEOPLE TOGETHER Fast Ethernet Wireless 11b g Print Server with Storage Server NAS User s Manual Version 1 0 February 2007 COPYRIGHT Copyright 2007 2008 by this company All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of this company Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation b
19. NAS System MS334455 from workgroup computers in My Network Places of the Windows O Please assign the shared folders and the user s read write authority Folder Name Enter the name for shared folder Path Designated the shared folder path or enable to share all folders in the storage Description The comments or description for the shared folder User Assign users with read write authority for the shared folder Read Write Select Read Only or Read Write Note You can not set sharing policy here for folders in NTFS partitions 21 If you want to set all users have the same authority to share the all folders in the storage please select Read amp Write Read Only or Not to Share here Note1 If you have set shared folders and the user s read write authority the New Storage Default Sharing Policy you set here will not enable Note2 If the storage has NTFS partitions all folders in NTFS partitions are Read Only even you choose Read Write here vd mn Pres E sc RB WS Jo so E us f Snr fis ss LU a sep thee File Server Storage name in the My network places geg a bereet WORKGROUF alphanumeric space and Workgre enen AID ju Can oddest shared lolders below Al shared folders can be accessed from My Network Places Please astign Ihe users read write authority for each shared folder ABerbon You cannot setup shanng policy here for fokle
20. Select Agmnt USBNCA v add Edie Delete AN Delete Selected Reset Advanced Setting E o 11 20 RECH d NOTE if an FTP connector ot die bmeout no fon and no Me tramster Ine cornechon vell be dscormectod auformabcaty Pore Dim 4 Open your web browser and enter ftp IP Address of the Server for example ftp 192 168 2 5 5 Enter user name and password to logon to the FTP Server 27 3 Web Management This server can be configured and managed on the Web Through Local Area Network or even Internet administrator can easily configure and manage the server s various main functions in browsers Simply enter the server s IP address into your browser s address field to start the configuration The default IP Address User Name and Password settings of the server are as follows IP Address 192 168 2 5 User Name Admin Password 1234 Note Please make sure that your computer is in the same segment network of the server or you cannot get into the web management of the server Connect to 192 168 2 5 Ee 1 f Default admin 1234 User name Password cece Remember my password 28 8 1 Status The status of the server will be displayed here You can find the information including system time firmware version network settings and the USB port status sn Fyre O Dry Md inde a SE PEJ E p Shag E EDIMAX k 7 Status and Information Ties page Gspirys the general f
21. Shared Key WPA Unicast WPA2 PSK is also for home and small business The Cipher Suite difference between WPA PSK and WPA2 PSK is that WPA2 PSK provides data encryption via the AES In contrast WPA PSK uses Temporal Key Integrity Protocol TKIP WPA2 PSK offers the highest level of security available When WPA2 PSK is selected please enter 8 64 characters as the Pre Shared Key Click lt Apply gt at the bottom of the screen to save the above configurations 43 Parameters Description Pre shared Key Format You can select Passphrase or Hex 64 characters format for the WPA pre shared key Pre shared Key Enter 8 to 64 digits as you select Passpharse format or 64 digits in the A F a f and 0 9 range as you select Hex format to be the key for the authentication within the network Click lt Apply gt at the bottom of the screen to save the above configurations 44 8 4 3 Advanced You can set advanced wireless LAN parameters of this sever The parameters include Fragment Threshold RTS Threshold Data Rate Preamble Type etc It is recommended that do not change these parameters unless you know what effect the changes will have on this server micaly advanced users who have a suficient inowiedoe about wireless LAN These sefings J Wow what effect fe changes wil have on your system 256 3348 2347 0 2347 5 Long Prea
22. WEP key 2 as its default key to transmit while the server can use WEP key 3 as its default key to transmit The two devices will communicate as long as the wireless device s WEP key 2 is the same as the server s WEP key 2 and the wireless device s WEP key 3 is the same as the server s WEP key 3 Encryption Key 1 4 Enter the four sets of keys the key order should be the same as the wireless device you want to connect 64 bit Input 10 digit Hex values in the A F a f and 0 9 range or 5 digit ASCII characters including a z and 0 9 as the encryption keys For example 0123456aef or test1 128 bit Input 26 digit Hex values in the A F a f and 0 9 range or 13 digit ASCII characters including a z and 0 9 as the encryption keys For example 01234567890123456789abcdef or administrator Click lt Apply gt at the bottom of the screen to save the above configurations 42 8 4 2 2 WPA PSK fam Security Settings This poge slow you h ihgure Pe wireless security Enable WEP of WPA could provert eny unauthorized eccess to your roles WPA Unicast Cipi eet eme rome Parameters Description Encryption Select WPA pre shared key encryption type WPA PSK is suitable for home and small business It uses TKIP for data encryption When WPA PSK is selected please enter 8 64 characters as the Pre
23. age dedicated to this server in the USB port 1 for disk management such as Add Delete Partitions or Format the disk If you just want to share the USB mass storage you can plug the storage in USB port 1 or 2 Note3 USB Flash Disk has to be plugged to USB port 2 Step3 Connect the power adapter to the server You must use the power adapter shipped along with the server do NOT use any other power adapter from other sources 4 Hardware Placement 4 1 Rear Panel SH oo LI USB2 USB1 Releas LAN EECH JOL 1 Power Jack Please plug the power adapter attached with the server to the power jack 2 Antenna Connector PS 2207SUg only The antenna connector of the server is reverse SMA connector It allows you to connecting an external antenna with reverse SMA connector to the server easily USB 1 and USB 2 The USB ports allow you to connect to printer or USB mass storage for oo network sharing 4 Release 2 and Release 1 The Release button is used to safely remove USB mass storage from your server Click the Release 1 and 2 buttons for over 5 seconds to remove device connected in the USB port 1 and port 2 individually The USB LED of the USB port will be blinking after you have clicked Release button for over 5 seconds Please unplug the USB mass storage while the USB LED is blinking When the USB LED is turning unlighted the release function is cancelled Note1 If the release function is cancelled the US
24. d Local or Network Printer The wizard needs to know which type of printer to set up Select the option that describes the printer you want to use 2 Local printer attached to this computer Automaticall Plug and Play printer O A network printer or a printer attached to another computer a To set up a network printer that is not attached to a print server LD use the Local printer option reg TT TIA 5 Choose Create a new port and Standard TCP IP Port Click Next Add Printer Wizard Select a Printer Port Computers communicate with printers through ports Select the port you want your printer to use If the port is not listed you can create a new port O Use the following port LPT 1 Recommended Printer Port Note Most computers use the LPT1 port to communicate with a local printer The connector for this port should look something like this Create a new port Type of port Standard TCP IP Port Ca me RR 51 6 Please make sure that the print server and the printer have turned on and connected to the network correctly before you continue Click Next Add Standard TCP IP Printer Port Wizard Welcome to the Add Standard TCP IP Printer Port Wizard You use this wizard to add a port for a network printer Before continuing be sure that 1 The device is turned on 2 The network is connected and configured To continue click Next Back i Cance
25. ddress assigned to the LAN client By default the End IP is 192 169 2 200 Domain Name You can specify a Domain Name for your LAN Lease Time In the Lease Time setting you can specify the time period that the DHCP Server lends an IP Address to your LAN clients The DHCP will change your LAN client s IP Address when this time threshold period is terminated Click lt Apply gt at the bottom of the screen to save the above configurations 35 8 4 Wireless PS 2207Sug only If you want to use the server through wireless LAN please set up the server through Ethernet first and make sure your wireless LAN setting is correct After setting the wireless LAN unplug the Ethernet cable and restart the server then you can start to use the server through wireless LAN If the wireless configuration does not work please plug the Ethernet cable again restart the server and configure the server through Ethernet until the wireless LAN settings are correct 8 4 1 Site Survey This page allows you to enable disable the wireless function and set the wireless networks that you want to connect If you want to automatically search and connect to the wireless networks nearby please click Site Survey button 36 Parameters Description Wireless Function You can select Auto Enable or Disable to manually configure the wireless function Auto Auto is the default setting
26. e USB storage device O Double click My Network Places in Windows You will find the USB storage device Note If you cannot find the device in My Network Places you can click Start and select Run Enter IP Address of the server to access the device Type the name of a program folder document or Internet resource and Windows will open it For you 23 Y My Network Places File Edit View Favorites Tools Help Kp Bec X bi Na Search E Folders EZ Address my Network Places f Local Network Network Tasks a Add a network place 1234_USB2_C on NAS SYSTEM Ms334455 View network connections dE Setup a home or small office network Y Set up a wireless network for a home or small office Ai View workgroup computers 8 Show icons For networked UPnP devices Other Places Di Desktop d My Computer CH My Documents VC Shared Documents Eg Printers and Faxes Details 8 Double click the device to logon to the folder User Name Please enter the user s name who has been allowed to access the folder Password Please enter the user s password Note1 In Windows multiple connections to a server or shared resource by the same user using more than one user name is not allowed Please make sure that you use one user name for one computer to access the same shared resource Note2 If you cannot logon to the shared folder it is recommended
27. e in USB1 port according to the following rules 1 It partitions the USB storage device to a partition with 160GB size and formats to FAT32 file system 2 If the rest of partition size is under 160GB then it will be partitioned as a partition Please wait for a moment System is adding partitions and formatting the device that is plugged in the USB1 port PPPS SSDS PPPS PSS gt gt gt gt gt rom e Add a Partition Please set the partition size and the file system that you want to create and format a new partition in the USB storage device attached in USB port 1 Then click Save to add the partition 81 8 6 5 Storage Status This Page shows the status of attached USB storage devices Storage Status This page shows Pie stats of al vato partions of atached rage Any rte parihon and any nor partibonad space of a achod storage vell not be Atclayod here USB Port 1215M su 0 1214 FAT Refresh USB Ga E Dre Parameters Description To safely remove the USB storage device please click Unplug Unplug Partition The partition names in the USB storage device Size Total available space of this partition Used Total used space of this partition Here shows the byte se count and the percentage of the total space Free This shows free space of the specified partition Sist The partition type of the partition lt can be FAT16 FAT32 atus NTFS and Linux Refresh Refre
28. e same access point cannot see each other decide that the channel is free and transmit at the same time The frames collide when they reach the access point and all of them are rejected When CTS protect is enabled the throughput will be a little lower but it will help to reduce the packet loss Select Auto the server will automatically enable the CTS protection mechanism when it is needed Select Always the function will be always enabled If you don t want to enable the function please select None Click lt Apply gt at the bottom of the screen to save the above configurations 46 Parameters Description Turbo Mode This sever supports specific ways to increase the data transfer rate at a time compress the data and decrease the waiting time to send the next data to the Access Point or Router this feature known as Turbo Mode enables higher throughput than IEEE 802 11g standard When the server is connecting to the Access Point or Router with the same proprietary Turbo Mode feature the Turbo Mode will be enabled automatically without any configuration WMM This server supports WMM function When you use the devices such as Voice over Internet Protocol VolP phones televisions VCRs and MP3 players IEEE 802 11e Quality of Service QoS The Wi Fi Alliance defined WMM as a profile of the IEEE 802 11e extensions for 802 11 networks will help to define the priorities of the data
29. e the installation PrintServer Utilities InstallShield Wizard InstallShield Wizard Complete Congratulation You have completed the PrintServer Utilities installation procedure Cancel 15 Add Printer After adding a Network Port of the print server to your PC you can follow the procedure described below to add printer to the Windows Note that following Add Printer steps are running in Windows XP the steps in other Operating Systems are similar 1 Click Start and select Printers and Faxes 2 Click Add a Printer 3 The Add Printer Wizard is displayed Click Next Add Printer Wizard Welcome to the Add Printer Y Wizard This wizard helps you install a printer or make printer connections through a USB port or any other hot pluggable port such as IEEE 1394 infrared and so on you do not need to use this wizard Click Cancel to close the wizard and then plug the printer s cable into your computer or point the printer toward pour computer s infrared port and turn the printer on Windows will automatically install the printer for you i If you have a Plug and Play printer that connects To continue click Next 16 4 Select Local printer attached to this computer and make sure that Automatically detect and install my Plug and Play printer is not selected Click Next Add Printer Wizard Local or Network Printer The wizard needs
30. ed Community Name public SNMP Device Index 1 lt A cancel _ 53 10 Click Finish Add Standard TCP IP Printer Port Wizard Completing the Add Standard TCP IP Printer Port Wizard You have selected a port with the following characteristics SNMP Yes Protocol LPR ott Device 192 168 2 2 Port Name IP_192 168 2 2 Adapter Type To complete this wizard click Finish 11 Select a suitable printer manufacturer and the printer model and click Next If your printer is not in the list click Have Disk to install the driver of the printer After installation the printer model will be added to the list Add Printer Wizard Install Printer Software The manufacturer and model determine which printer software to use pa Select the manufacturer and model of pour printer If your printer came with an installation disk click Have Disk If your printer is not listed consult your printer documentation for compatible printer software Manufacturer A Printers Gestetner Mf HP Laserjet IIP PostScript Cartridge v52 2 Cu infotec Ki HP LaserJet Plus lwatsu z S HP LaserJet Series Il Y This driver is digitally signed Windows Update Have Disk y La 2 Tell me why driver signing is important ETEY ETE E 54 12 Choose to set the print whether as a default printer or not Click Next Add Printer Wizard Name Your Printer You must assign a name to t
31. ers Please perform Window s standard Add New Printer procedure 1 Click Start choose Settings and select Printers and Faxes 2 Click Add a Printer 3 The Add Printer Wizard is displayed Click Next Add Printer Wizard Welcome to the Add Printer Y Wizard This wizard helps you install a printer or make printer connections i If you have a Plug and Play printer that connects through a USB port or any other hot pluggable port such as IEEE 1394 infrared and so on you do not need to use this wizard Click Cancel to close the wizard and then plug the printer s cable into your computer or point the printer toward your computer s infrared port and turn the printer on Windows will automatically install the printer for you To continue click Next Cancel 65 4 Select A network printer or a printer attached to another computer Click Next Add Printer Wizard Local or Network Printer The wizard needs to know which type of printer to set up Select the option that describes the printer you want to use Local printer attached to this computer To set up a network printer that is not attached to a print server use the Local printer option MT pm Sep 5 Select Connect to a printer on the Internet or on a home or office network and enter the URL of server The URL format is http IP Address of the Server 631 Queue Name The IP Addres
32. ettings assigned by the DHCP Server to the server The assigned IP Address will be shown in the IP Address fields If no DHCP Server is present within the network please assign the network settings of the server manually Please click Next once you have found appropriate network settings for the server By default the network settings are as follows IP Address 192 168 2 5 Subnet Mask 255 255 255 0 IP Ackhess Assignment O DHCP IP Address 10 0 mm Subnet Mask 255 255 255 0 Default Gateway 10 0 11 1 Manual IP IP Address EX 168 2 5 Subnet Mask 255 255 255 0 Default Gateway 0 0 0 0 Back A Men JD Cancel 6 Review the network settings of the server If there is no problem click Save to save the settings and reboot the server Sais Oveniaw To confirm the IP Address settings please click Save button Device Name MS334455 IP Address Setting Manual IP IP Address 192 168 2 5 Subnet Mask 255 255 255 0 Default Gateway 0 0 0 0 7 The server is saving the settings and rebooting please wait for a while 10 8 The configuration is finished For more settings please click Advanced Settings to get into the web management of the server Or click Finish to close the wizard Congrat lations The IP Address settings are finished For more advanced settings please click Advanced Settings to get into the web management of the
33. etween the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio technician for help FCC Caution This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and person s body excluding extremities of hands wrist and feet during wireless modes of operation This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment Federal Communication Commission FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment In order to avoid the possibility of exceeding the FCC radio frequency exposure limits human proximity to the antenna shall not be less than 20cm 8 inches during normal operation The antenna s used for this transmitter must not be co located or operating in conjunction with any other antenna or transmitter R amp TTE Compliance Statement This equipment complies with all the req
34. his printer Type a name for this printer Because some programs do not support printer and server name combinations of more than 31 characters it is best to keep the name as short as possible Printer name HP LaserJet Do you want to use this printer as the default printer O Yes O No TOTO eg 13 You have added the network printer to the PC successfully The information of the printer is displayed in the windows Click Finish Add Printer Wizard Completing the Add Printer Y Wizard You have successfully completed the Add Printer Wizard You specified the following printer settings Name HP Laseret Share name lt Not Shared gt Port 1P_192 168 2 2 Model HP LaserJet Default Yes Test page Yes To close this wizard click Finish 55 8 5 1 2 MAC OS LPR Printing Line Printer Remote technology allows Macintosh computers to connect to printers via TCP IP LPR Printing can be set up on any Macintosh with version 9 x above MAC 10 4 x To enable LPR Printing in Macintosh 10 4 x please follow the procedures below 1 Open Print and Fax from the System Preferences With the Printing tab selected click the Add button When the Printer Browser opens select IP Printer In the IP Printer screen please configure as below Protocol Select Line Printer Daemon LPD as the Protocol IP Address Set the address to the server s IP Address for example 1
35. ine Confirm password alphanumeric space and underine Seve Reset Cancel ATTENTION User name and password are case sensitive and the max length of these strings is 20 Dre Parameters Description User Name Enter the user name of this user Description Enter the description for this user Set the password for the user to logon to the USB mass Password storage Confirm Re type the password of this user for confirmation Password Click lt Save gt at the bottom of the screen to save the above configurations Note The max number of users you are able to set for sharing FTP File server is 32 71 8 6 2 File Server You can add edit the File Server name shared folders and sharing policies for sharing files via My Network Places Be n S e eServer File Server Storage name in the My network places WR atpnanumene and undertine Workgroup t Se alphanumeric space and Shared Folders Test USB1 C V v New Storage Default Sharing Policy ror Parameters Description Name The File Server name that shows in My Network Places The workgroup that the server will be joined in My Workgroup Network Places By default the workgroup is WORKGROUP o A brief description for this File Server This string will be Description ae SE shown at the detailed information in My Network Places Click
36. ion By default it is disabled Click lt Apply gt at the bottom of the screen to save the above configurations 33 8 3 2 DHCP Server This server has a built in DHCP Server If the DHCP Server is enabled it will automatically give your LAN clients a unique IP Address also include Default Gateway and DNS Server IP Address if you have designated De Omer amp i the P Acker of he system manually for geing P Address rom LEM Server res system SO Nas Du Bn UHL Server and to Gripatch the IP edaress to other ciont IP Address Settings Obtain an IP address automatically Use the fofowing P address dre Parameters Description A default gateway is a node a router on a network that Default Gateway Ip serves as an access point to another network Please enter the IP Address of the default gateway A Domain Name System DNS server is like an index of IP addresses and Web addresses If you type a Web Domain Name address into your browser such as www server com a Server IP DNS server will find that name in its index and the matching IP address Please enter the DNS Server IP Address here Start IP The Start IP is the first IP Address assigned to the LAN client By default the Start IP is 192 168 2 100 Click lt Apply gt at the bottom of the screen to save the above configurations 34 Parameters Description End IP The End IP is the last IP A
37. ity This server supports 64 128 bit WEP data encryption that protects your wireless network from eavesdropping It also supports WPA PSK and WPA2 PSK security which provide stronger security level for your wireless network Security Settings Tes page alons you lo conbgure De wireless securty Enable WEP or WPA could prevert any unauthortred access to your wireless nator SZ Cancel 40 8 4 2 1 WEP ETT Security Settings Tivs page alons you lo conbgure De wireless securty Enable WEP or WPA coud prevert any unauthonred access lo your wireless D fregk Key Length tout e Hea 10 charactor Orem Parameters Description Encryption Select WEP encryption type You can select 64 bit or 128 bit length for the data Key Length encryption Longer key length can provide stronger security but worth communication performance You can select Hexadecimal or ASCII format for the Key Format encryption key Click lt Apply gt at the bottom of the screen to save the above configurations 41 Parameters Description Default Key Select the default key from the key1 to 4 The default key will be used to encrypt the transmission data from the server Note The default key on the wireless device that you want to connect and the server can have different default WEP keys as long as the keys are in the same order In other words the wireless device can use
38. l 7 Enter the IP Address of the print server in the Printer Name or IP Address Click Next Add Standard TCP IP Printer Port Wizard Add Port For which device do you want to add a port Enter the Printer Name or IP address and a port name for the desired device Printer Name or IP Address 192 168 2 2 Port Name IP_192 168 2 2 52 8 Select Custom and click Settings When you have finished the settings at step 9 click Next to continue Add Standard TCP IP Printer Port Wizard Additional Port Information Required The device could not be identified The detected device is of unknown type Be sure that 1 The device is properly configured 2 The address on the previous page is correct Either correct the address and perform another search on the network by returning to the previous wizard page or select the device type if you are sure the address is correct Device Type O Standard lt Back O Nex JX Cance 9 Select LPR and enter Ipt1 for printer attached in USB Port 1 or Ipt2 for printer attached in USB Port 2 in the Queue Name click OK Configure Standard TCP IP Port Monitor Port Settings Port Name Printer Name or IP Address Protocol O Baw Raw Settings IP 92 168 2 2 192 168 2 2 O LPR rt Numbe LPB e Queue Name ku E LPR Byte Counting Enabled SNMP Status Enabl
39. lder for sharing You can also click New Folder to create a new share folder Note Only the folders in USB storage devices will be shown as icons in the pop up window due to the share function is restricted to folders not files http 192 168 2 5 NAS Download Microsoft Internet Explorer DER Cas New Folder E Done Internet 75 8 6 3 FTP Server You can add edit shared folders and sharing policies for sharing files via FTP service FTP Server e 10 edl FTP folders below hor FTP geste Please 15350 Me users rotkrete athonty tor each FTP bider Esch user an belong to one FTE k ier orby Attention You cannot set fokders in NTFS partbors es FIP foid FTP Folders MT II E Write Select Admini USBI V Add Ede Delete All Delete Selected Reset Advanced Setting NOTE if an FTP connector ns idie bmeout no actor and no Me tramter ne cornechon vell be dscormectod auformabcaty Dro Parameters Description Add Click Add and fill the information in the Add Edit FTP Folder page to add a new shared folder for FTP server Edit Select any shared folders in FTP Folders list and click i Edit to modify its setting Click Delete All to delete all the shared folders in FTP Delete All Folders list Click Delete Selected to delete the selected shared Delete Selected f S folders in FTP Folders list Reset Click Reset to reset
40. ng service by TCP IP The server can support IPP printing in Windows 2000 XP 2003 by default By using the IPP printing you can share the printer to all the PC s that can access the server by IP You can even share your printer to Internet users LPR When the print server function is enabled the LPR protocol will be enabled as well LPR Printing Line Printer Remote technology allows users to connect to printers via TCP IP for printing sharing The computer with Windows 98SE Me NT 2000 XP 2003 MAC OS 9 x above and Linux Unix operating systems can use the protocol to share printing in the network Print Server Name The name of the print server You can use this name to identify the print server when you are searching for the print server by the Windows utilities By default the print server name is the last 6 digit of MAC ID with prefix PS Queue Name of USB Port 1 The server has two USB 2 0 ports If you connect a printer to the USB port 1 you have to designate a printer queue name to the port Then you can use this name to access the printer port By default the printer queue name is Ipt1 for port 1 Queue Name of USB Port 2 The server has two USB 2 0 ports If you connect a printer to the USB port 2 you have to designate a printer queue name to the port Then you can use this name to access the printer port By default the printer queue name is Ipt2 for port 2 Click lt Apply
41. o Q R Y ae Delete Hold Resume Stop jeStop Jobs j SuperMario jpg Spooling LPR job 55 complete Sass sss ww Name SuperMario jpg 60 8 5 1 3 Linux Unix The server is available for TCP IP printing by Unix Linux LPD Line Printer Daemon protocol This section explains how to set the server with the LPD protocol in the Unix Linux system The following procedures are running in the Fedora Core 4 system 1 Select Printing from System Settings Printer configuration fedora lle Action Test Help 3 gt 1 2 Edit Delete Default Apply Queue name v Shared Default Description 61 3 Click Forward Add a new print queue Add a new print queue On the following screens you will be asked to provide basic information for adding a new print queue You will be able to edit the more advanced options afterwards Nothing will be done to your settings until you hit Finish on the last screen 4 Set the printer queue name and the short description of the printer and 5 click Forward Add a new print queue Queue name Please enter a name for this queue Choose a short name that begins with a letter and contains no spaces About If you like you can enter a description of the printer to help you identify it more easily Short description HP PSC 1210 In the following screen please configure as below Then click Forward to contin
42. older name Click Browse to open the explorer window to select the Shared Folder s shared folder path or click Share all folders in storage to Path share the whole storage Here you can assign some users with read write authority for this shared folder Select the users in System Users t and click Add to add into Share Users Click Add All to sers add all users Select the users in Share Users and click Delete to remove the selected users Click Delete All to remove all users Click lt Save gt at the bottom of the screen to save the above configurations 74 Parameters Description Here you can assign the read write authority for this shared folder You can select Read Only for read only Authority sharing or select Read amp Write to give users full access right Description Fill the share comments for this share item here Click lt Save gt at the bottom of the screen to save the above configurations Note You can not set sharing policy here for folders in NTFS partitions e Browser Shared Folder s Path When you click the Browse button you can see the following pop up window that shows the USB mass storage devices Please select the USB devices from left panel the right panel will show the directories in this USB storage device Choose the folder you want to share and click Submit to select this fo
43. ormation and tne status of the System General information Syston Tene 2000111 00 55 52 MAL Adaress 00 Oe Ze 44 55 40 Firmware vergoen 120 Prira Server Status Pret Server Eratze LES Enable WE Enable FUMIFTP Server Status FIWFTP Server MS44540 Workgroup WORKGROUP Descrigico NAS SYSTEM USB Status usat Ott une USR Dit Network Status IP oddress 192 166 25 Subnet Mask 255 2552550 frend 0000 rem 29 8 2 Basic 8 2 1 Time Zone The Time Zone allows your server to refer the time configured here This information is used for recording files created and modified date in the FTP File server Enatte Funchon A RH Times From To i oro Parameter Description Select the time zone of the country you are currently in Set Time Zone o l The server will set its time based on your selection Time Server Set the time from a time server the default time server is Address 192 43 244 18 If your region is currently in DST please check the Daylight Savings Enable Function and set the time period of Daylight Savings Times From Select the beginning date of the Daylight Savings Time Times to Select the end date of the Daylight Savings Time Click lt Apply gt at the bottom of the screen to save the above configurations 30 8 2 2 Password You can change the password required to log into the server s web based management By default the password is 1234
44. oth 802 11g and 802 11b wireless devices If there are only 802 11b wireless devices in the network you can set the server to this mode 2 4GHz G This server can be compatible with both 802 11g and 802 11b wireless devices If there are only 802 11g wireless devices in the network you can set the server to this mode 2 4GHz B G If you have a mix of 802 11b and 802 11g wireless devices in your network it is recommended to set the server to this mode This mode is also the default setting ESSID The ESSID up to 32 printable ASCII characters is the unique name identified in a WLAN The ID prevents the unintentional merging of two co located WLANs You may specify an ESSID for the server and then only the device with the same ESSID can interconnect to the server By default the ESSID of the server is default Channel The radio channel used by the wireless LAN All devices in the same wireless LAN should use the same channel When you have set the wireless mode to Ad Hoc you have to select the channel that is used in the Ad Hoc network Site Survey Click Site Survey and then the server will scan all the channels to find all the access points routers stations within the accessible range of your server You can then connect to one of the networks you have selected Click lt Apply gt at the bottom of the screen to save the above configurations 38 e Site Survey Tool From the
45. r provides FTP File Server function which let you share a USB storage device to all PCs in your Intranet Internet It supports SAMBA protocol in File Server let you share files via Network Neighborhood And also supports FTP Server for your FTP clients to upload download files from the server 7 1 File Server To share the USB mass storage or USB Flash Disk from the server please follow the procedures below 1 Open your Web Browser and enter the IP address of the server to logon to the web management of the server The default settings of the server are IP Address 192 168 2 5 User Name admin Password 1234 2 Set the users who are authorized to access to the USB storage device in the Users menu of FTP File Server page O Click Add Enter the user information including User Name and Password 20 Users setup Users list D At Es Delete Selected Lette AS Heset Apani Data Carter 3 Set the share folders of the USB storage device which are allowed to access by authorized users in the Storage Server menu of FTP File Server page O Set the following information to identify your USB storage device on the network Storage Name By default the storage name is the last 6 digit of MAC ID with prefixes MS Workgroup The default workgroup is WORKGROUP Description The device name displayed in My Network Places Follow the default settings you will find a device
46. reen Ta SC Network traffic transferring or receiving Blinking through the LAN port 5 Setup Wizard This Setup Wizard is for you to configure the server s IP Address This wizard can be run in Windows 98SE Me 2000 XP The following procedures are operated in Windows XP Procedures are similar for Windows 98SE Me 2000 1 Insert the CD shipped along with the server into your CD ROM drive The Autorun exe program should be executed automatically If not run Autorun exe manually from Autorun folder in the CD 2 The following screen will be displayed Click Setup Utility Print Server and Storage Server NAS Click here to visit www edimax com 3 The wizard will search for all the servers within the network and list the connected device in each port of the servers Please select the server you want to configure and click Next Device List Select one device to configure IP Address Connected Po Connected Port2 M5334455 192 168 2 5 WinFast Disk 128 M Status 1 Device Found 4 Please enter user name and password to login the server By default the user name is Admin and password is 1234 Click Next to continue User Name Password Login User Name admin Password 5 The wizard will try to determine your network settings automatically If a DHCP Server is present within the network the wizard will automatically obtain and configure the network s
47. rs in NTFS partitions Shared Folders Folder Name Path Description ReadWriteSelect Test USBI C v v The seting below wil ech lo any storage wsch you dont set any st folder above In Pas woy af users have he same ff Read A Vinte Read Or f or Not to Share to access amp Y ape Alertior if the storage hes NTFS parsbona af New Storage Default Sharing Policy rer 22 fee Ce ves Favors Took ret Quo s gd Se pean frr E Ss RH k A EDISI 168 7 Sree Do uv On v DUDO He hie My III A piatos WER wiphanumeric and underline Workgroup o i ur siphanumeric space and You cen added shared folders below Ai shared folders can be accessed from My Network Pisces Please asugn te users read write minority tor each shared k ier A erbon You carrot setup shang pobcy here for folders in NTFS partion Shared Folders Folder Name Path _ Description Read Write Select Test USB1ICA WOIV 6 404 Eat Dele Al D se Selectos Reset The sating below wil apply lo ary storage whch you dort sel any shared K ier above in frz wey af users have he same Race Read 4 Write Read Org or Not lo Share to access folders in hw siorage Aleron if the storage has NTFS pardons af fokjers in NTFS parthora are Read Ord even you choose Read 4 verte hera New Storage Default Sharing Policy gt Reed 4 vito Read Orvy Net to Share Save 4 Access the share folder of th
48. rtte Shor Preantie A n Abys Note 5 Enti Disadie Enst Diss is Parameters Description Fragment Threshold specifies the maximum size of Fragment packet during the fragmentation of data to be Threshold transmitted If you set this value too low it will result in bad performance Enter a value from 256 to 2346 When the packet size is smaller than the RTS threshold RTS Threshold the server will not use the RTS CTS mechanism to send this packet The range is from 0 to 2347 Click lt Apply gt at the bottom of the screen to save the above configurations 45 Parameters Description Data Rate There are several data rates including Auto 1 2 5 5 11 6 9 12 18 24 36 48 54Mbps for you to select When the Auto is selected the device will choose the most suitable transmission rate automatically Preamble Type The preamble defines the length of the CRC block for communication among wireless devices There are two modes including Long and Short Preamble Therefore for an IEEE 802 11g network to be interoperable with IEEE 802 11b clients it must use larger preambles than it would normally need CTS Protect The RTS CTS protection mechanism is needed to ensure that all the devices can access the medium when IEEE 802 11b and IEEE 802 119 devices are co existence in the same network Especially when Hidden Node is existent Hidden Node occurs when different clients connected to th
49. s server supports USB mass storage with FAT16 32 EXT2 EXT3 and NTFS file systems This server can support Read Only when you use the partition with NTFS file system 2 The maximum file size of a single file is less than 2GB when using a partition with FAT16 32 file system due to operating system limitation whereas for a partition with EXT2 3 file system the file size is up to 4GB 3 The maximum number of users you are able to set for sharing FTP File server is 32 4 The maximum users that reserve the connection such as open and edit the files directly through the server to the FTP or File Server concurrently are 10 users 69 8 6 1 Users This page allows you to add edit delete users for FTP File server Users setup Users list II EL Amin Data Contor Add Es L Ges Seat 1 Goes Roser Dre Parameters Description Aud Click Add and fill the information in the Add a New User page to add a new user for FTP File server Edit You can select any user in Users list and click Edit to i modify the profile Click Delete Selected to delete the selected users in Delete Selected Users list Delete All Click Delete All to delete all the users in Users list Reset Click Reset to reset selection in Users list 70 e Add Edit Users 192 148 2 Sindee on sx Ow Sun wv Add a New User User Name alphanumeric and vergeet ne menne undert
50. s should be the server s IP Address The number 631 is IPP standard port number Queue Name is the queue name of the USB port that your printer is connected to The default queue name is Ipt1 for printer attached to USB Port 1 and Ipt2 for printer attached to USB Port 2 One example of the URL is http 192 168 2 2 631 lpt1 After entering the URL of the server click Next 66 Add Printer Wizard Specify a Printer If you don t know the name or address of the printer you can search for a printer that meets your needs What printer do you want to connect to O Browse for a printer Connect to this printer or to browse for a printer select this option and click Next Name URL http 192 168 2 2 631 ptt Example http server printers myprinter printer reg mmm em Select a suitable printer manufacturer and the printer model and click Next If your printer is not in the list click Have Disk to install the driver of the printer After installation the printer model will be added to the list Add Printer Wizard Install Printer Software The manufacturer and model determine which printer software to use all Select the manufacturer and model of your printer If your printer came with an installation disk click Have Disk If your printer is not listed consult your printer documentation for compatible printer software Manufacturer Printers Gestetner SW HP La
51. serJet IIP PostScript Cartridge v52 2 HP AHP Lasenet IBM i HP LaserJet Plus Iwatsu EJ HP Laserjet Series Il v infotec v Mem o nuna mm ES This driver is digitally signed Windows Update Tell me why driver signing is important reg pm ST 67 7 Choose to set the print whether as a default printer or not Click Next Add Printer Wizard Default Printer Your computer will always send documents to the default printer unless pou specify otherwise Do you want to use this printer as the default printer Back Cl Next gt D Cancel 8 You have added the network printer to the PC successfully The information of the printer is displayed in the windows Click Finish Add Printer Wizard Completing the Add Printer Wizard You have successfully completed the Add Printer Wizard You specified the following printer settings Name unknown on http 192 168 2 2 631 Default Yes Location Comment To close this wizard click Finish Cancel 68 8 6 FTP File Server The server provides FTP File Server function which let you share a USB storage device to all PCs in your Intranet Internet It supports SAMBA protocol in File Server let you share files via Network Neighborhood And also supports FTP Server for your FTP clients to upload download files from the server When you start to use the FTP File server please read the following information carefully 1 Thi
52. sh the USB storage status 82 8 7 Tools 8 7 1 Configuration Tools This page allows you to backup or restore the settings and reset to factory defaults If you want to backup the settings please click Save and designate the file path where you want to save the settings To restore the settings please click Browse to select the file and click Upload If you want to restart the server with the factory default settings click Reset You can also click the Release 1 button in the rear panel of the server over 10 seconds to reset to default settings Comfia Tests Configuration Tools Use he Backup tooi to save the system s current configuradons to a Me named coro tr You can then use Be Restore tool to restore the saved configuradons to the system Afernatvely you can ute the Restore to Factory Deta toot to force the system th lora to ite factory defauts 83 8 7 2 Firmware You can upgrade new firmware of this server in this page Click Next and enter the file name and the path of the firmware in the appropriate field or click Browse button to find the firmware file on your computer Click Apply and the firmware will be updated in several minutes Note If you have started upgrading firmware you have to follow all the upgrading steps Do not turn off the server during upgrading X W Cae ves Peris Too mk ES Qu O 22H mm frr E e BR A res tra 148
53. tall the utilities PrintServer Utilities InstallShield Wizard Choose Destination Location Select folder where setup will install files A Install PrintServer Utilities to C Program Files PrintServer Utilities C Change D InstallShield 13 5 The system will start to install the utilities automatically PrintServer Utilities InstallShield Wizard Setup Status PrintServer Utilities Setup is performing the requested operations Installing CAWINDOWS system32 pswin dll UU 6 The Remote Port Setup is for you to add the network port of the print server to your computer Please click Add Remote port setup Remote port list Delete 7 Enter the Print Server Name and the IP Address of the server and also select the port number then click OK to add the print server port to your computer Print Server Name It is the last 6 digit of MAC ID with prefix PS IP Address By default it is 192 168 2 5 Port Designate the printer port name for each port By default it is Ipt1 for USB port 1 and Ipt2 for USB port 2 14 Create remote port Print Server Name P5334455 ef IP Address 1921 68 2 5 Cancel r Port Iv lipti TT Metz M pt3 8 The network port of the print server is set completely Click Exit Remote port setup Remote port list PS334455 P1 9 Click Finish to complet
54. to know which type of printer to set up O A network piero pr ateched iO another computer To set up a network printer that is not attached to a print server J use the Local printer option chek CL news zeegt 5 Choose the suitable Print Server Network Port which was created by the installation process and click Next Add Printer Wizard Select a Printer Port Computers communicate with printers through ports Select the port you want your printer to use If the port is not listed you can create a new port Use the following port PS334455 P1 PrintServer Network Port v Note Most computers use the LPT1 port to communicate with a local printer The connector for this port should look something like this ya a ya O Create a new port Type of por MIXTO zeegt 17 6 Select the printer manufacturer and the printer model and click Next If your printer is not in the list click Have Disk to install the driver of the printer After installation the printer model will be added to the list Add Printer Wizard Install Printer Software The manufacturer and model determine which printer software to use VAL Select the manufacturer and model of your printer If your printer came with an installation disk click Have Disk If your printer is not listed consult your printer documentation for compatible printer software Manufacturer A Printers Diconix Digital
55. tod Partitions Remee All Partitions Reset sro 79 Parameters Description Auto Partition amp Format By clicking this button the system will partition and format the USB storage device in USB port 1 to FAT 32 file system automatically Partition The partition names in the USB storage device Size Total available space of this partition Start Cylinder The first cylinder of the partition End Cylinder The last cylinder of the partition File System The file system of the partition You can format your USB storage device by using this tool Tool This server supports to format the device in FAT16 FAT32 or EXT2 file format If you want to select the partition select the check box Select here Add a Partition If there are free spaces in the USB storage device you can find the button in the Select column By clicking this button you can launch the Add a Partition page for you to add a new partition on the USB storage device Remove You can click Remove Selected Partitions to remove the Selected selected partitions on USB storage device Partitions Remove All You can click Remove All Partitions to remove all the Partitions partitions on USB storage device Reset You can click Reset to reset selection in partition list 80 e Auto Partition amp Formatting The storage tool will partition and format the USB storage devic
56. torage devices Please select the USB devices from left panel the right panel will show the directories in this USB storage device Choose the folder you want to share and click Submit to select this folder for sharing You can also click New Folder to create a new share folder Note Only the folders in USB storage devices will be shown as icons in the pop up window due to the share function is restricted to folders not files A http 192 168 2 5 NAS Download Microsoft Internet Explorer Path ep New Folder Si Done a S Internet 78 8 6 4 Storage Tools You can use the storage tools here to format add or remove partitions in the storage attached to USB Port 1 Note1 It is recommended that use the Storage tools to partition and format the USB storage that you want to share in the network usually the disk is brand new or no need to move to other PC environment Note2 Please make sure that the USB storage device is plugged and idle and you are the only user to format or manage the partitions Note 3 The partition size with FAT16 file system should be less than 2GB and for FAT32 or EXT2 file system the partition should be less than 160GB adto Of Format tool cannot format the partion larger Sian 10064 Aho the partition storage with FAT32 ae Port e Auto Partition amp Format gt File ge Se A cancer symm To E Format c 123M 1 223 FATS y PATI Hemeve Selec
57. ue Select a queue type Select Network Unix LPD as the queue type Server Enter the IP Address of the server for example 192 168 2 253 Queue Set the queue name to Ipt1 or Ipt2 62 Add a new print queue Queue type Server Queue 192 168 2 253 LPT Add a new print queue Printer model Select the printer manufacturer and model Depending on how the remote queue is configured you may need to select the generic PostScript option here PSC 1205 PSC 1210 PSC 1300 63 7 Please review the settings If the settings are no problem click Finish Add a new print queue Finish and create the new print queue About to create the following queue Type Unix Print Queue Queue LPT1 192 168 2 253 Printer HP PSC 1210 Question Would you like to print a test page Answering yes will apply all changes and print a test page to this printer _ sn JC m 9 If the test page is printed without problem please click Yes If it is failed to print please click No to go back to Printer configuration fedora screen and configure again Information Sent CUPS test page to printer queue Does it look okay 64 8 5 2 IPP Printing The server can support IPP printing in Windows 2000 XP 2003 by default By using the IPP printing you can share the printer to all the PC s that can access the print server by IP You can even share your printer to Internet us
58. uirements of DIRECTIVE 1999 5 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity R amp TTE The R amp TTE Directive repeals and replaces in the directive 98 13 EEC Telecommunications Terminal Equipment and Satellite Earth Station Equipment As of April 8 2000 Safety This equipment is designed with the utmost care for the safety of those who install and use it However special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria Belgium Denmark Finland France Germany Greece Ireland Italy Luxembourg the Netherlands Portugal Spain Sweden and the United Kingdom The ETSI version of this device is also authorized for use in EFTA member states Iceland Liechtenstein Norway and Switzerland EU Countries Not intended for use None E Dpi Contents EPO ele e EE 1 Product PACK ADC sc atada ds 2 Hardware Installation oooccccoccccoocnnnconnncoroncnaronnns 3 Hardware Placement nneennnoenneennnsnnnennrrennrerrrrerrrerrrene 4 A O 4 A2 GHEET 6 SSUP WIZA sisas 7 Print

User`s Manual - akcesoriaPC.pl

Contents

Download Pdf Manuals

Related Search

Related Contents