USER`S MANUAL - Tyconpower.com
Contents
1. TP MS4x4 4 Port Gigabit PoE Injector USER S MANUAL TYCON Power Systems TYCON POWER SYSTEMS User s Manual TP MS4x4 V5 1 General Information The TP MS4x4 is a DC DC PoE Power over Ethernet Injector provide up to 4 different voltage DC input and four different voltage PoE output output power maximum 1A port data rate can be 1OM 100M 1000M The polarity of each PoE output can be reversed if you need to reverse the output polarity This manual will help you to install and setting the PoE injector 2 Hardware Description Data in Data Power out Front panel detail the port number is as the diagram shows Rear panel detail TYCON POWER SYSTEMS User s Manual TP MS4x4 V5 LED Indicator There are 4 LEDs on the front panel to indicate the input and output power status of each port Green A valid power device is detected on this port Active current is 80mA at power device is detected on this port Off No input power apply or input source alarm Alarm voltage is less than 58 VDC or larger than 10 5 VDC Alarm current is 2A Data Input The upper ports 1 4 on the front panel are used for Gigabit Ethernet data input All four ports with surge protection TYCON POWER SYSTEMS User s Manual TP MS4x4 V5 Power Input The input voltage of TP MS4x4 is 12VDC to 57VDC it is common negative design the green terminal CON1 on rear panel is used for power input wiring it can be connected to m2. aximum 4 different sources with 4 different voltages the jumper A B C of JPI on rear panel controls the input output connection its setting as below 1 jumper on O off PoE Output 1 2 1 3 1 4 PoE 1 2 3 4 VIN1 Factory setting PoE 1 2 3 lt VINI PoE 4 VIN4 PoE 1 2 4 lt VINI PoE 3 VIN3 PoE1 2 VINI PoE3 VIN3 PoE4 VIN4 PoE1 3 4 lt VINI PoE2 VIN2 PoE1 3 lt VINI PoE2 VIN2 PoE4 VIN4 PoE1 4 VINI PoE2 VIN2 PoE3 VIN3 PoE I lt VINI PoE 2 VIN2 PoE 3 VIN3 PoE 4 VIN4 TYCON POWER SYSTEMS User s Manual TP MS4x4 V5 PoE Output The bottom ports 1 4 on the front panel are used for carry PoE output the output voltage is the same as input no regulated Normally as detailed below Data pair A on line and 2 Data pair B on line 3 and 6 Data pair C plus V on line 4 and 5 Data pair D plus V on line 7 and 8 Output Polarity Reverse for technician operation only The TP MS4x4 may deliver PoE output with reverse polarity Just move related jumpers from pin 1 2 to pin 2 3 and then Data pair C carry V on line 4 and 5 Data pair D carry V on line 7 and 8 Open the cover the JP4 JP11 on the PCB responds for the output polarity of port 1 4 each two jumpers should be paired moved to ensure the path enough for the through current P SPO amp SPL JP8 amp JP9 JP6 amp JP7 JP4 amp JP5 Pinl 2 short pinl amp pin2 RJ45 pair C pin4 amp 5 carry PoE positive voltage Pin2 3 short pi
3. n2 amp pin3 RJ45 pair C pin4 amp 5 carry PoE negative voltage CON VINA VINS YIN PP EET VIN34VINIH JP1 1 4 1 3 1 2 PORT FEA ue 123 P JE HEH PORT 123 pio P EEA PORTS ONE 123 IPS LED2 LEDI a E g TYCON POWER SYSTEMS User s Manual TP MS4x4 V5 4 Technical Information Data Rate 10M 100M 1000M Input voltage I2VDC to 57VDC Maximum PoE power Current limited 1 A port PoE protection over current over under voltage LEDs Green PD detect Red Power ready Off No power apply Operating temperature 40 C 75 C Operation humidity 90 relative humidity non condensing Storage temperature 40 C 85 C Dimension 40mm H x118mm W x90mm D DIN RAIL Mountable Surge protection on data input ports ga Clamping Voltage Data 16 5V CI PP 5A t p 8 20us I O pin to GND Peak Pulse Current 20A tp 8 20us Pin Protected All 8 pin protected lt 3pF VR OV f IMHz I O pin to GND Max Shut Capacitance lt 1 5 pF VR OV f IMHz Between I O pins IEC61000 4 2 ESD 15kV air 8kV contact IEC COMPATIBILITY EN61000 4 IEC61000 4 4 EFT 40A 5 50ns IEC61000 4 5 Lightning 20A 8 20us TYCON POWER SYSTEMS
Download Pdf Manuals
Related Search