Model 1020 Standalone Enclosure User Manual
Contents
1. Web Site www canoga com Email fiber canoga com Copyright 2003 2005 Canoga Perkins Corporation All Rights Reserved EdgeAccess Universal Chassis System Model 1020 Users Manual Model Number 1020 UM Product Number 6913070 Rev D 01 2008 2 EdgeAccess Model 1020 Model 1020 Standalone Enclosure User Manual The Model 1020 standalone enclosure shown in Figure 1 supports one 2U sized module that is managed through either SNMP or Sideband Management Control SBMC Figure I Model 1020 Standalone Enclosure The front provides three switches three LEDs two connectors and a slot for a managed module The back includes an AC power cord socket The AC power supply provides 5 VDC to the module Switch Setting Selects MDM TRM for EIA 232 port MDM DTE terminal for SLIP TRM DCE terminal for VT100 F1 NRM F2 typically for Loopback for the module F1 Local loopback typically Note Set to NRM except to isolate a fault NRM Normal operation F2 Remote loopback typically HDX FDX for 10BASE T port HDX Half duplex FDX Full duplex Note Ifthe link partner is set to auto negotiation the link uses 10M and follows the HDX FDX switch setting for this port otherwise set this switch to match the other switch on the link LED State Definition PWR Off No power Green Power is on Tx for 10BASE T port Off No transmission Green blinking Transmission activity LNK Rx for 10BASE T port Off No link Green Link is established at full duple2. CANOGA PERKINS Model 1020 Standalone Enclosure User Manual NOTICE This device contains static sensitive components It should be handled only with proper Electrostatic Discharge ESD grounding procedures NOTE Cet quipement contient des composants sensibles aux d charges lectro statiques Il doit absolument tre manipul en respectant les r gles de mise la terre afin de pr venir de telles d charges NOTICE Canoga Perkins has prepared this users manual for use by customers and Canoga Perkins personnel as a guide for the proper installation operation and or maintenance of Canoga Perkins equipment The drawings specifications and information contained in this document are the property of Canoga Perkins and any unauthorized use or disclosure of such drawings specifications and information is prohibited Canoga Perkins reserves the right to change or update the contents of this manual and to change the specifications of its products at any time without prior notification Every effort has been made to keep the information in this document current and accurate as of the date of publication or revision However no guarantee is given or implied that the document is error free or that is accurate with regard to any specification Canoga Perkins Corporation 20600 Prairie Street Chatsworth California 91311 6008 Business Phone 818 718 6300 Monday Friday 7 a m 5 p m Pacific Time FAX 818 718 6312 24 hrs
3. t the COM Properties dialog on the Port Settings tab check for these selections e Bits per second 19200 bps e Data bits 8 e Parity None e Stop bits 1 e Flow control None Click OK HyperTerminal connects to the system and the VT100 terminal emulation starts To use the module and access its management functions in the 1020 enclosure see the User Manual for the module EdgeAccess Model 1020 Specifications Dimensions 10 0 L x 6 25 W x 1 625 H 254 mm x 159 mm x 43 mm Weight 3 0 Ibs 1 4 kg Power 10 W maximum 100 to 240 VAC 50 to 60 Hz autoranging Operating Environment 0 to 50 C Up to 90 Non condensing Regulatory Compliance ETL cETL UL 60950 CAN CSA C22 2 No 60950 EN IEC 60950 EN 60825 1 2 CDRH CFR21 FCC Part 15B IC 003 VCCI Class A C Tick AS NZS 3548 EN 55022 Class A EN 61000 3 2 EN 61000 3 3 EN 55024 R amp TTE Directive EN 300 386 CE Mark Warranty Information Current Warranty information is available on line in the Client Login Area of the Canoga Perkins web site www canoga com or by contacting Technical Support at 800 360 6642 voice or fiber canoga com email EdgeAccess Model 1020 CANOGA PERKINS EdgeAccess Model 1020
4. x Amber Link is established at half duplex Blinking Data is received EdgeAccess Model 1020 3 Connector Manages EIA 232 Serial port for modem or terminal 10BASE T Half or full duplex Ethernet supports only modules that include SNMP such as 2x46 or L3x1 Installing and Using the 1020 Enclosure To use the 1020 enclosure 1 Place it on a secure surface with room for air flow and within 10 ft 3 m of the AC power source Insert a managed module in the guide rails and press it firmly into the backplane then secure the thumbscrew finger tight Plug the power cord into the rear of the 1020 enclosure then plug it into the AC power source this turns on the power To turn off the power unplug the power cord To set any switches on the module install the module in the 1020 enclosure connect all cables and access the module see the User Manual for the module Use HyperTerminal for your first VT100 session These steps briefly describe how to set up your PC for a terminal connection For details on using Windows see your Windows documentation 1 2 Turn on your PC When the Windows desktop appears click Start then highlight Programs Accessories the HyperTerminal Folder and then click HyperTerminal At the Connection Description dialog select an icon enter a name for the connection to the system and click OK At the Connect To dialog pull down the Connect using menu select the COM port and click OK A
Download Pdf Manuals
Related Search