Manual Supplement
Contents
1. r1 r2 rn On page 20 replace the Extended Documentation Mode section with Extended Documentation Mode In the Extended Documentation mode 1654B only the Tester stores the measurement result with the measurement location P P P N P E or N E You can select the information before or after the measurement with The definitions are P P L P N L N P E L PE N E N PE On page 22 replace Extended Documentation Mode section with Extended Documentation Mode In the Extended Documentation mode 1654B only the Tester stores the measurement result with the measurement location R1 R2 R2 r1 r2 or rn You can select the information before or after the measurement with The definitions are R1 R2 Rx1 2 R2 R 2 r1 x1 r2 2 rn x5 On pages 24 and 26 replace step 4 with 4 For the 1654B only press 2 to select between Q and mO resolution for the test results The mO resolution test takes between 30 and 60 seconds to complete On page 29 replace the last two bullets in step 4 and the Note with 1654B only e E Smooth DC current to test type B RCD e s Delayed response to S type B time delayed smooth DC current RCD 10 11 1 Manual Supplement 1652C 1653B 1654B Users Note For RCD type B or S type B E S you must test with both phase settings and measure the trip current On page 33 replace the last two bullets in step 3 1654B only e Smooth DC current to test type2. 100 300 or 500 mA If the RCD has a special nominal current setting other than the standard options 10 30 100 300 500 mA you can use a custom setting with the VAR mode On page 54 replace the Tripping Speed Test T table with Tripping Speed Test 4T Test Functi RCD Current Selection est FuncHon Lo mAl30 mA 100 mA 300 ma 500 mA 1000 mA var eee T T Rame EV EY vy yvy y auto Ayeye y S S d Notes Mains voltage 100 V 265 V ac 50 60 Hz 1 Type B RCDs require mains voltage range of 195 V 265 V 2 Type AC RCDs only 3 Type A RCDs are limited to 700 mA not available for Type B RCDs 2 15 3
3. B RCD e s Delayed response to S type B time delayed smooth DC current RCD On page 52 replace the second Table with 0 0019 Hi Current mN mode 2 15 digits 456 oor Me Trip mode 3 6 digits Hi Current mode 2 4 digits oio No Trip mode 3 Hi Current mode 2 Notes 1 Valid for resistance of neutral circuit lt 20 Q and up to a system phase angle of 30 Test leads must be zeroed before testing 2 1654B only 3 Valid for mains voltage gt 200 V Change 3 464 On page 3 add the following to the Symbols table G Conforms to relevant South Korean EMC Standards On page 45 under General Specifications remove EMC and add Electromagnetic Environment IEC 61326 1 Portable Applies to use in Korea only Class A Equipment Electromagnetic Compatibility Industrial Broadcasting amp Communication Equipment This product meets requirements for industrial Class A electromagnetic wave equipment and the seller or user should take notice of it This equipment is intended for use in business environments and is not to be used in homes 2 2 15 1652C 1653B 1654B Users Manual Supplement Change 4 114 On page 32 under the note remove the following sentence Type A and type B RCDs do not have the 1000 mA option available On page 32 under To measure RCD tripping current replace step 2 with 2 Press F to select the RCD current rating 10 30
4. Manual Supplement Manual Title 1652C 1653B 1654B Users Supplement Issue 4 Print Date September 2010 Issue Date 2 15 Revision Date Page Count 3 This supplement contains information necessary to ensure the accuracy of the above manual This manual is distributed as an electronic manual on the following CD ROM CD Title 1652C 1653B 1654B CD Rev amp Date 9 2010 CD PN 3798444 2010 2015 Fluke Corporation All rights reserved l J KE 1652C 1653B 1654B Users Manual Supplement Change 1 56800 On page 3 add the following bullet e Do not use in CAT Ill or CAT IV environments without the protective cap installed The protective cap decreases the possibility of arc flash caused by short circuits On page 6 under Operating the Tester Using the Rotary Switch add the following AWarning Do not use in CAT Ill or CAT IV environments without the protective cap installed The protective cap decreases the exposed probe metal to lt 4mm This decreases the possibility of arc flash from short circuits On page 45 under General Specifications add the following to the Safety section Complies with EN IEC 61010 031 2002 A1 2008 Change 2 59912 On page 18 Table 8 replace row 2 with Extended documentation mode Simultaneously press the Power button and the Up cursor key 1654B only Additional information is stored with an insulation test result P P P N P E N E and with a continuity test result R1 R2 R2
Download Pdf Manuals
Related Search