SPECTRA BATTEN 12T3 EXTERIOR
Contents
1. SPECTRA BATTEN 1273 EXTERIOR No e 300090909999 9 Order code LEDJ259 User manual Spectra Batten 12T3 Exterior Safety WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION INPUT VOLTAGE OF 100 240V SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty Spectra Batten 12T3 Exterior Safety IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution Never remove warning or informative labels from the equipment Do not ope2. LEDJ91 1M Interior to IP Rated Exterior DMX Cable Also remember that DMX cable must be daisy chained and cannot be split Spectra Batten 12T3 Exterior DMX Set up Notice Be sure to follow figures 2 amp 3 when making your own cables Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out s ioo RR S DMX 512 in 3 pin XLR g s 3 pin XLR XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 2 cold Pin 1 Ground 1 ground Pin 2 Negative 3Hot 3Hot Pin 3 Postive FIGURE 3 FIGURE 2 Special Note Line termination When longer runs of cable are used you may need to use a DMX terminator on the last unit to avoid erratic behaviour LEDJ260 Termination reduces signal transmission problems and interferance it is always advisable to connect a DMX terminal resistance 120 Ohm 1 4 W between pin 2 DMX and pin 3 DMX of the last fixture AC Plug The Spectra Batten 12T3 features captive power cords terminated with IP66 connectors for pow er input and power linking The fixture is then supplied with a short 13A to IP66 connector power cord If at any stage the 13A plug is removed please follow the chart below Any changes to the connector types must be verified by a PAT test or equivalent
3. M button for 2 seconds to show COL on the LED screen Now tap the M button to scroll through the three separate colours red green and blue To adjust the brightness of each individual colour use the UP and DOWN buttons The r represents Red G Green and B Blue The two digits after it are the brightness 00 to 99 Note 00 Off 99 Full on Examples If you set r G and B to 00 the Spectra Batten 24T3 will have no LEDs on blackout If you set r to 99 and G and B to 00 the Spectra Batten 24T3 will be 100 Red Built in programmes To activate the units built in programmes press and hold the M button for 2 seconds to show P 01 on the LED screen Now use the UP and DOWN buttons to scroll through the built in programmes from P 01 to P 07 Now tap the M button to select the desired speed and adjust by using the UP and DOWN buttons Tap the M button once more to select the desired flash value and adjust by using the UP and DOWN buttons Speed values S 00 S 99 00 slow 99 fast Flash values F 00 F 99 00 slow 99 fast In P 01 you can set a specific static colour When in P 01 tap the M button and use the UP and DOWN buttons to scroll through the list of built in static colours 0 White RGB 1 Red 2 Orange 3 Light Yellow 4 Green 5 Cyan 6 Blue 7 Purple 8 Pink 9 Yellow 10 Cool white 11 W
4. electrical safety test Connection Wire Europe AC Live Brown AC Neutral Blue AC Ground Green Yellow Power linking The Spectra Batten 12T3 supports power linking You can link up to 8 products at 120 VAC or 16 at 240 VAC This product supplied with a fixed power input cord This product is not suppled with a power link cable however power cables are available as an option see page 7 Spectra Batten 12T3 Exterior Trouble Shooting One or more fixtures are completely dead Fixtures reset correctly but all are responding erratically or not at all to the controller Fixtures reset correctly but some are responding erratically or not at all to the controller No power to the fixture Internal fuse has blown The controller is not connected The 3 pin XLR out of the controller does not match the XLR out of the first fixture i e signal is reversed Poor data quality Bad data link connection Data link not terminated with 120 Ohm termination plug Incorrect addressing of the fixtures One of the fixtures is defective and disturbs the data transmission on the link The 3 pin XLR Out on the fixture do not match pins 2 and 3 reversed Check that the power is switched on and cables are connected Contact your Prolight dealer Connect the controller Install a phase reversing cable between the controller and the first fixture in the link Check the data quality
5. number 0 to 5 To choose one of the two DMX channels tap the M button and use the UP and DOWN buttons to scroll the through the 1 3 3 4 or 5 channel options dP 1 1 channel mode dP 2 3 channel mode RGB dP 3 3 channel mode Function dP 4 4 channel mode dP 5 5 channel mode To confirm your choice pres the M button For DMX functions please see the DMX charts below and overleaf Master salve mode To set the unit as the master simply use any of the function modes on the unit To set the unit as a slave unit s press the M button to show SLA on the LED display The unit will follow in sequence with the master unit DMX Charts 1 channel mode DMX chart e ee O e O 1 184 206 Dark Blue 253 255 Warm White Spectra Batten 12T3 Exterior DMX Programme Charts DMX Charts 3 channel mode DMX chart RGB 0 255 Green 0 100 3 channel mode DMX chart function 4 channel mode DMX chart 0 255 Master dimmer 0 100 5 channel mode DMX chart 0 255 Green 0 100 0 255 Master dimmer 0 100 0 255 Strobe slow to fast Spectra Batten 12T3 Exterior DMX Set up DMX 512 DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DA
6. that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please seperate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal Create the right effect www prolight co uk
7. If much lower than 100 the problem may be a bad data link connection poor quality or broken cables missing termination plug or a defective fixture is disturb ing the link Inspect the connection and cables Correct the connection Repair or replace the damaged cables Insert a termination plug into the output socket of the last fixture Check that DMX address setting is correct Bypass one fixture at a time until normal operation is regained Unplug both connectors and connect them together Have the fixture serviced by a qualified technician Install a phase reversing cable between the fixtures or swap pin 2 and 3 in the fixture that behaves erratically Spectra Batten 12T3 Exterior Trouble Shooting Contact a technician for servicing Fixture black out suddenly The fixture is resetting the effect f if the problem persists Allow the fixture to cool down Fixture is too hot Make sure that all air vents are not blocked No Light Disconnect the fixture and return it The LEDs are damaged to your dealer The power supply settings do not match Disconnect the fixture and check the local AC voltage and frequency settings and correct if necessary 10 Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with seperate collection systems This marking shown on the product or its literature indicates
8. TA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX Linking e DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DATA Cable DMX cable requirements for DMX operation The Spectra Batten 12T3 can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output Further exterior DMX and power cables IP Rated Exterior Power Cable can be purchased from all good sound and lighting suppliers or Prolight dealers Please quote DMX Power LEDJ141 1M LEDJ146 1M LEDJ142 2M LEDJ147 2M IP Rated Exterior DMX Cable P Aa en LEDJ144 10M LEDJ149 10M Interior to exterior DMX
9. arm white To add strobe tap the M button again and use the UP and DOWN buttons to set strobe from F 00 to F 99 To confirm your setting press the M button Note F 00 slow F 99 fast Auto run mode To activate the units auto run mode press and hold the M button for 2 seconds to show AUT on the LED screen Now tap the M button to select the desired speed and adjust by using the UP and DOWN buttons Tap the M button once more to select the desired flash value and adjust by using the UP and DOWN buttons To adjust the fading value tap the M button and set the value from U 00 to U 99 by using the UP and DOWN buttons To confirm your setting press the M button Speed values 8 00 S 99 00 slow 99 fast Flash values F 00 F 99 00 slow 99 fast Fading values U 00 slow U 99 fast Spectra Batten 12T3 Exterior DMX Programme Charts DMX Mode To activate the units DMX mode press and hold the M button for 2 seconds to show 0 01 on the LED screen and use the UP and DOWN buttons to set the first digit in the DMX address from 0 to 9 To set the second digit of the DMX address tap the M button and use the UP and DOWN buttons to select the desired number form 0 to 9 Now to set the final digit of the DMX address tap the M button again and use the UP and DOWN buttons to select the desired
10. ay lead to danger e g short circuit burns electric shocks LED failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property Spectra Batten 12T3 Exterior Introduction Introduction Features e 12 x 3W tri colour LEDs e Beam angle 40 degrees e 0 100 dimming and variable strobe e DMX channels 1 3 3 4 or 5 selectable e Static colour colour fade colour change colour mix auto master slave and DMX modes e 3 push button menu with LED display e IP rated power in out sockets e IP rated 3 pin DMX in out sockets Lumen chart e Power consumption 50W 40 Lux 2600 779 345 205 140 e Power supply 100 240V 50 60Hz Rag IP rating IP 66 pu e es a E O Es Dimensions 619 x 120 x 140mm a ee e Weight 2 6kg m u EE A a mo Overview 0 M 1 2 3 4 5 Identification 1 Tightening knobs 2 Mounting bracket 3 Power in 4 DMX in 5 DMX out 6 Power out 7 LED display 8 Mode button 9 Up button 10 Down button Setup Operating Instructions The Spectra Batten 12T3 Exterior is a DMX 512 controllable unit made up of high efficiency RGB LEDs and will operate in stand alone master slave or DMX control modes 3 Spectra Batten 12T3 Exterior Operation Modes Operation modes Colour mix mode To activate the units colour mix mode press and hold the
11. n the equipment and do not modify the equipment Do not connect this equipment to a dimmer pack Do not switch the equipment on and offin short intervals as this will reduce the system s life Do not expose to flammable sources or gases Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable Make sure that the available voltage is between 100V 240V Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically Avoid direct eye exposure to the light source while the product is on e If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service Only use fuses of same type and rating Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS WARRANTY One year from date of purchase OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation m
Download Pdf Manuals
Related Search