User manual Richter Bass Amplification
Contents
1. Paramid frq Selects the MID frequencies to be cut or boosted in conjunction with the PARAMID GAIN control 7 To access LO mid frequencies turn the FREQUENCY control anticlockwise to access HI mid frequencies turn the FREQUENCY control clockwise 7 Paramid Level Sets the level of boost or cut applied to the frequency set by control 6 For frequency boost turn the control clockwise For frequency cut turn the control anti clockwise 8 Treble Controls the high frequency response of the pre amplifier g Presence Controls the high frequency signal content of the pre amplifier The PRESENCE control is set at 3K 10 Limiter Allows the on board limiter to be defeated if desired With the switch in the out position the limiter is engaged The LIMITER is automatically triggered at high output levels and is designed to prevent power amp distortion at high output levels When the limiter is autpmatically triggered an LED lights up to indicate the limiter is active It is possible to have the limiter engaged but not have the LED active The LIMITER monitors both power amp clipping and load so it automatically registers the cabinet impedance and sets itself accordingly 11 Volume Sets the overall listening level of the amplifier 12 Horn switch Switches the on board horn either on or off 13 0 1 XLR socket for direct injection of the amplifier signal to a mixing desk or additional power amplifier The XLR socket provides a low impedanc2. CONNECTION C E CALIBRE ATTENTION DEBRANCHER LE CORDON D ALIMENTATION AVANT TOUTE INTERVENTION FXReturn O ATTENTION REFROIDI PAR VENTILATEUR NE PAS OBSTRUER LES GRILLES CAUTION FAN COOLED DO NOT OBSTRUCT THE FAN OR VENT APERTURES I yg D AERATION ET DE VENTILATION Richt Lane 1 Inputs normal and High inputs are provided for connection of bass guitars High output basses either Active or Passive should be connected via the High socket Low output basses should be y 8 connected using the normal input High output basses may also be placed in the Normal input if pre amp overloading is desired 2 Gain This control is used to set the level of gain present in the pre amp The higher the level of gain the more the signal will clip producing distortion The GAIN control should be used in conjunction vith the VOLUME control 9 to produce the desired signal characteristics 3 Compressor Engages and disengages the on board compressor This compresses the input signal giving a punchier sound In association with the compressor are two LED s one indicating that the compressor is engaged and one indicating the compressor is active Jt is possible to have the compressor engaged but it only be active during certian periods of playing typically the most dynamic sections 5 Bass Controls the low frequency response of the pre amplifier 6 Graphic EQ The 7 band onboard GRAPHIC EQ allows extens
3. ELECTRIC SHOCK LTIAL 230v O NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE Fuse RATING amp SUPPLY VOLTAGE CAUTION FOR CONTINUED PROTECTION EHEN RISK OF FIRE REPLACE ONLY WITH SAME TYPE AND RATED FU CAUTION TO REDUCE THE RISK OF ceoTRIG SHOCK DO NOT REMOVE COVERS NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL ONLY JARNING THIS EQUIPMENT MUST BE EARTHED ATTENTION REMPLACER LE FUSIBLE SEULEMENT PAR LE MEME TYPE ET LE MEME CALIBRE Avis RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR ATTENTION DEBRANCHER LE CORDON D ALIMENTATION H MAXIMUM POWER CONSUMPTION AVANT TOUTE INTERVENTION lead Phones 120 Watts 50 60 Hz Em O D SERIAL y CE gt Designed And Assembled in the UK by BLT Industries LTD 4 Inputs Normal and High inputs are provided for connection of bass guitars High output basses either Active or Passive should be connected via the High socket Low output basses should be connected using the normal input High output basses may also be placed in the Normal input if pre amp overloading is desired 2 Gain This control is used to set the level of gain present in the pre amp The higher the level of gain the more the signal will clip producing distortion The GAIN control should be used in conjunction with the VOLUME control 10 to produce the desired signal characteristics 3 Compressor Engages and disengages the on board cpmpressor This compresses the input s
4. Laney Richter Bass Amplification User manual www laney co lis IMPORTANT SAFETY INSTRUCTIONS WARNING When using electric products basic cautions should always be followed including the following Read all safety and operating instructions before using this product All safety and operating instructions should be retained for future reference Obey all cautions in the Operating instructions and on the back of the unit All operating instructions should be followed This product should not be used near water e a bathtub sink swimming pool wet basement etc This product should be located so that its position does not interfere with its proper ventilation It should not be placed flat against a wall or placed in a built up enclosure that will impede the flow of cooling air This product should not be placed near a source of heat such as stove radiator or another heat producing amplifier Connect only to a power supply of the type marked on the unit adjacent to the power supply cord Never break off the ground pin on a power supply cord Power supply cords should always be handled carefully Never walk or place equipment on power supply cords Periodically check cords for cuts or signs of stress especially at the plug and the point where the chord exits the unit The power supply cord should be unplugged when the unit is to be unused for long periods of time If this product is to be mounted in an equipment rack rear support should be
5. NEL ONLY ann pis QUIPMENT MUST BE EARTHE EMPLACER LE FUSIBLE SEULEMENT PAR LE MEE ae a LE MEME CALIBRE SOU DE DE CHOC ELECTRIQUE NE PAS OUVRIR BRANCHER LE CORDON D ALIMENTATION AVANT TOUTE INTERVENTION RES A rl ESE ma Designed And Assembled in the UK by BLT Industries LTD Loudspeakers 4 OHM TOTAL MINIMUM IMPEDANCE 00 O REFER To USER MANUAL FOR RECOMMENDED TunerOut LOUDSPEAKER CONNECTIONS R4 R4H Front Bass AMPLI RAEN 5 5 0 RO 4 2 6 a A a HIER 3 7 x cil By ee cf ci 20 js se 3 les he wa 4 9 te ee oy io e 0 INPUTS ENHANCE 40Hz 80Hz 160Hz 400Hz 800Hz 2KHz 6KHz TREBLE Fee D I Power Tor 606 e R4 R4H Rear 115A L_ 230V1 LOUDSPEAKERS Fuse amp SUPPLY VOLTAGE RECOMMENDED SPEAKER CONNECTIONS A KR LOAD OF NO less 4 d IAN 4 OHMS MAY Bi core AT ANY mu NUMBER A IN Designed And Assembled in the UK by BLT Industries LTD TES a CLASS 2 WIRING MAY BE USED Maximin Pon Power En gt AUTION do ln ith RISK OF ELECTRIC SHOCK DO NOT e SERVICEABLE PARTS INSIDE U eu THIS APPLIANCE TO RAIN Ol rt TI go A TION FOR ca AET N I FIRE OYLY WITH SAME TYPE A WARNING His EQUIPMENT MUST BE MO ant T PARLEUR Wis isa DE CHOC ELECTRIQUE NE PAS OUVRIR ATTENTION REMPLACER LE FUSIBLE SEULEMENT PAR LE MEME TYPE ET LE ENS HA MEMI USER es BER seno no auno PERSONNEL ae JE RISK OF FIRE Ol ATTENTION Si REFERER AU MANUEL D UTILISATION POUR LA
6. R CONNECTIONS Extension 4 Inputs Normal and High inputs are provided for connection of bass guitars High output basses either Active or Passive should be connected via the High socket Low output basses should be connected using the normal input High output basses may also be placed in the Normal input if pre amp overloading is desired 2 Gain This control is used to set the level of gain present in the pre amp The higher the level of gain the more the signal will clip producing distortion The GAIN control should be used in conjunction with the VOLUME control 12 to produce the desired signal characteristics 3 Compressor Engages and disengages the on board compressor This compresses the input signal giving a punchier sound In association with the compressor are two LED sone indicating that the compressor is engaged and one indicating the compressor is active IJt is possible to have the compressor engaged but it only be active during certain periods of playing typically the most dynamic sections Richter Lane 4 Enhance The ENHANCE control provides an increased definition at the low end of the frequency spectrum giving you a tighter punchier sound The ENHANCE control does this by providing a dip in the frequency response of the amplifier at y 6 approximately 200hz This dip eliminates some of the secondary harmonics of the important lou frequencies around 40 80 Hz producing a thicker sound Turni
7. RVICEABLE FARTS INSIDE aan PA A Designed And Assembled in the UK by BLT Industries LTD 8 OHMS MINI LOUDSPEAKER IMPEDANCE CAUTION REFER TO USERS awa OR RecoumeNDED CORDON D ALIMENTATION AVANT iss 2 wams ma est CAUTION FAN COOLED DO NOT OBSTRUCT THE FAN OR VENT APERTURES Normal and High inputs are provided for connection of bass guitars High output basses either Active or Passive should be connected via the High socket Low output basses should be connected using the normal input High output basses may also be placed in the Normal input if pre amp overloading is desired This control is used to set the level of gain present in the pre amp The higher the level of gain the more the signal will clip producing distortion The GAIN control should be used in conjunction with the VOLUME control 12 to produce the desired signal characteristics Engages and disengages the on board compressor This compresses the input signal giving a punchier sound In association with the compressor are two LED s one indicating that the compressor is engaged and one indicating the compressor is active IJt is possible to have the compressor engaged but it only be active during certian periods of playing typically the most dynamic sections The ENHANCE control provides an increased definition at the low end of the frequency spectrum giving you a tighter Punchier sound The ENHANCE control does this by providing a dip in the fr
8. cabinet must not be less than 8 Ohms Connecting cabinets that have a lower impedance than 8 Ohms vill result in the amplifier overheating Continual use in this manner may cause permanent damage Connecting a cabinet with an impedance of greater than 8 Ohms will cause no damage to the amplifier but will result in a reduced output 12 Tuner out Socket for connecting external tuner 13 FX LOOP Send and return sockets are provided for connecting external effects_units Richter Laney T3 16A L_ 290 REMOVE CON Fuse Raro 2 Su VOLTAGE REFER SERVING To CUALED PERSONNEL O WARNING TO A THE RISK OF FIRE OR ELECTR RS Front EQUALISATION Bass AMPLIFIER el a 9 2 a Re a La aS gs Q 1 3 e 20 7202 o Ne 2 2 6 Ne 2 2 2 N e2 LIMITER Horn 20 ol oa 3 330 i gt Ah 9 a IO O MS A A here Les O F gt 98 0 cow s ae K 5 5 e Ss 5 o p ns Power ENHANCE pa mo un TREB VOLUME POWER 6 Posa iii dodo RS Rear Mo 450 CAUTION To To REDO E THE RISK OF ELECTRIC SHOCK DO NOT Gol ec RGR KU mue FIRE A ee une qa EE Amel us An IE D UTILISATION POUR tara Kiste we the HLECrRIQUE NE PAS OUVRIR ATTENTION REMPLACER LE FUSIBLE SEULEMENT R LE MEME TYPE ET LE MEME CALIBRE Pai Power CONSUMPTION ATTENTION DEBRANCHER LE ATIS 50 60 HZ TOUTE INTERVENTION ot 1 Inputs 2 Gain 3 Compressor 4 Enhance 5 Bass 1 O EXTENSION LOUDSPEAKER SERIAL NUMBER SE
9. d be connected using the normal input High output basses may also be placed in the Normal input if pre amp overloading is desired Richter Lane 2 Gain This control is used to set the level of gain present in the pre amp The higher the level of gain the more the signal will clip producing distortion The GAIN control should be used in conjunction with the VOLUME control 10 to produce the desired signal characteristics y 4 3 Compressor Engages and disengages the on board comprssor This compresses the input signal giving a punchier sound In association with the compressor are two LED sone indicating that the compressor is engaged and one indicating the compressor is active Jt is possible to have the compressor engaged but it only be active during certian periods of playing typically the most dynamic sections 4 Enhance The ENHANCE control provides an increased definition at the low end of the frequency spectrum giving you a tighter punchier sound The ENHANCE control does this by providing a dip in the frequency response of the amplifier at approximately 200hz This dip eliminates some of the secondary harmonics of the important lou frequencies around 40 80 Hz producing a thicker sound Turning the control through to its maximum has the effect of boosting both the low and high frequency content of the signal whilst not effecting the mids 5 Bass Controls the low frequency response of the pre amplifier 6
10. e 8 Treble Controls the high frequency response of the pre amplifier 9 Horn Switch Switches the on board horn either on or off 10 Volume Sets the overall listening level of the amplifier 11 D 1 XLR socket for direct injection of the amplifier signal to a mixing desk or additional power amplifier The XLR socket provides a low impedance balanced output signal 12 Phones Headphone output for silent practicing 13 Tuner out Socket for connecting external tuner 14 FX Loop Send and return sockets are provided for connecting external effects units R2 Front p EQUALISATION R2 Basi 5 0 A 350 metal LA A y ee R2 Rear i WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK x Fuse RATING amp SUPPLY VOLTAGE e or EREN Yo REDUCE THE RISK OF ELECTRIC SHOCK Do NoT REMOVE COVERS NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL ONLY WARNING THIS EQUIPMENT MUST BE EARTHED ATTENTION REMPLACER LE FUSIBLE SEULEMENT PAR LE BRE rae ie ET LE MEME CALII VIS RISQUE DE Clos fis ales PAS OUVRIR ATTENTION Bat ALIMENTATION AVANT T Toute INTERVENTION ae MAKINO POWER Con EN ON 240 Warts 30 NE JAS SERIAL OQ aL J Designed And Assembled in the UK by BLT Industries LTD 1 Inputs Normal and High inputs are provided for connection of bass guitars High output basses either Active or Passive should be connected via the High socket Low output basses shoul
11. e balanced output signal Richter Lane 14 Ext Speaker This socket should be used to connect an extension cabinet socket The impedance of the extension cabinet must not be less y than 8 Ohms Connecting cabinets that have a lower impedance than 8 Ohms will Tesult in the amplifier overheating Continual use in this Manner may cause Permanent damage Connecting a cabinet with an impedance of greater than 8 Ohms will cause no damage to the amplifier but will result ina reduced output 15 Tuner out Socket for connecting external tuner 16 FX Loop Send and return sockets are provided for connecting external effects_units R3 R3H Front ott Be ee ee a te te gee ce o 5 e or CUE ha a ama A Tass vos O ETLE R3 Rear LTSAL 116V WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK RAUHA POR CONEA PRETEC AN AANB RISE oF FUSE RATING amp SUPPLY VOLTAGE EICE pepiar ERRENA MEM E RISK OF ELECIRIE SROCK Do nor REMOVE COVERS NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL ONLY JARNING THIS EQUIPMENT MUST BE NTARTHED ATTENTION Kein LE FUSIBLE SEULEMENT PAR LE MEME TYPE ET LE MEME CALIBRE PUES RISQUE DE DE CHOC ELECTRIQUE N PAS OUVRIR BRANCHER LE CORDON D ALIMENTATION AVANT TOUTE beca Maxim WER MI ons REO T A RISK OF ELECTRIC SHOCK DO NOT OPEN AN o es CE Designed And Assembled in the UK by BLT Industries LTD REER To UseR MANA FOR LOUDSPEAKE
12. equency response of the amplifier at approximately 200hz This dip eliminates some of the secondary harmonics of the important lou frequencies around 40 80 Hz producing a thicker sound Turning the control through to its maximum has the effect of boosting both the low and high frequency content of the signal whilst not effecting the mids Controls the low frequency response of the pre amplifier Richter Lane 6 Lo Paramid frq Selects the LO MID frequencies to be cut or boosted in conjunction with the LO PARAMID LEVEL control 7 To access low LO mid frequencies turn the FREQUENCY control anticlockwise to access higher LO MID frequencies turn the FREQUENCY control clockwise y 10 7 Lo Paramid Level Sets the level of boost or cut applied to the frequency set by control 6 For frequency boost turn the control clockwise For frequency cut turn the control anti clockwise 8 Hi Paramid frq Hi Paramid Frequency Selects the HI MID frequencies to be cut or boosted in conjunction with the Hi PARAMID LEVEL control 9 To access low Hi mid frequencies turn the FREQUENCY control anticlockwise to access higher Hi MID frequencies turn the FREQUENCY control clockwise 9 Lo Paramid Level Sets the level of boost or cut applied to the frequency set by control 8 For frequency boost turn the control clockwise For frequency cut turn the control anti clockwise 10 Treble Controls the high frequency response of the pre ampli
13. fier 11 Limiter Allows the on board limiter to be defeated if desired With the switch in the out position the limiter is engaged The limiter is automatically triggered at high output levels and is designed to prevent power amp distortion at high output levels When the limiter is autpmatically triggered an LED lights up to indicate the limiter is active It is Possible to have the limiter engaged but not have the LED active The LIMITER monitors both power amp clipping and load so it automatically registers the cabinet impedance and sets itself accordingly 12 Volume Sets the overall listening level of the amplifier 13 Horn switch Switches the on board horn either on or off 14 D 1 XLR socket for direct injection of the amplifier signal toa mixing desk or additional pover amplifier The XLR socket provides a low impedance output signal 15 Ext Speaker This socket s should be used to connect an extension socket cabinet The impedance of the extension cabinet must not be less than 8 Ohms Connecting cabinets that have a lower impedance than 8 Ohms will result in the amplifier overheating Continual use in this manner may cause permanent damage Connecting a cabinet with an impedance of greater than 8 Ohms will cause no damage to the amplifier but will result ina reduced output 16 Tuner out Socket for connecting external tuner 17 FX Loop Send and return sockets are provided for connecting external effects units Ric
14. hter Laney a R1 R2 R3 R3H R4 R4H R5 Power Output 65W 120W 165W 165W 300W 300W 300W Maximum Power Consumption 120W 240W 300W 300W 450W 450W 450W 50 60Hz Input Impedance Normal Hi 1MOhm 1MOhm 1MOhm 1MOhm 1MOhm 1MOhm 1M Ohm Input Sensitivity Norma Hi 20 40mV 10 20mV 12 24mV 12 24mV 12 24mV 12 24mV 12 24mV FX Loop Level 700mV 800mV 800mV 800mV 800mV 800mV 800mV Nominal Minimum Ext Speaker n a 8 Ohms 8Ohms 4Ohms 8Ohms 4Ohms 8 Ohms Impedance eg 2x8 Ohms eg 2x8 Ohms or 1x4 Ohms or 1x4 Ohms Recommended Minimum Extension n a 60 Watts 80 Watts 165 Watts 300 Watts Speaker Power Rating 150 Watts 4 Ohms 150 Watts 4 Ohms 100 watts 8 Ohms 150 Watts 8 Ohms Recommended Richter n a R115 R410 R410 R410 R410 R410 Extension Cabinets or R115 amp R115 or R115 amp R115 or R115 or 2xR410 or 2xR410 Richter Laney Amplification N Newlyn Road Cradley Heath West Midlands B64 6BE United Kingdom x WWW laney co uk J In the interest of on going product development Laney reserves the right to amend specifications without prior notification
15. ignal giving a punchier sound In association with the compressor are two LED s one indicating that the compressor is engaged and one indicating the compressor is active It is possible to have the compressor engaged but it only be active during certian periods of playing typically the most dynamic sections Note that the higher the gain the greater the level of compression 4 Enhance The ENHANCE control provides an increased definition at the low end of the frequency spectrum giving you a tighter punchier sound The ENHANCE control does this by providing a dip in the frequency response of the amplifier at approximately 200h2 This dip eliminates some of the secondary harmonics of the important low frequencies around 40 80 Hz producing a thicker sound Turning the control through to its maximum has the effect of boosting both the low and high frequency content of the signal whilst not effecting the mids 5 Bass Controls the low frequency response of the pre amplifier Richter Lane y 6 Paramid frg Selects the MID frequencies to be cut or boosted in conjunction with the PARAMID GAIN control 7 To access LO mid frequencies turn the FREQUENCY control anticlockwise to access HI mid frequencies turn the FREQUENCY control clockwise 3 7 Paramid Level Sets the level of boost or cut applied to the frequency set by control 6 For frequency boost turn the control clockwise For frequency cut turn the control anti clockwis
16. ive tonal shaping to be achieved With the sliders along the centre line the GRAPHIC EQ will exert a flat signal response it is at this point that individual frequency bands can be cut or boosted Moving the slider beneath the centre line will incur a frequency cut conversely pushing the slider above the centre line facilitates frequency boost As a general rule avoid extreme settings of the sliders try to set the GRAPHIC with as little cut or boost as possible 7 Treble Controls the high frequency response of the pre amplifier 8 Limiter Switch Allows the on board LIMITER to be defeated if desired With the switch in the out position the limiter is engaged The limiter is automatically triggered at high output levels and is designed to prevent power amp distortion at high output levels When the limiter is autpmatically triggered an LED lights up to indicate the limiter is active It is possible to have the limiter engaged but not have the LED active The limiter monitors both power amp clipping and load so it automatically registers the cabinet impedance and sets itself accordingly g Volume Sets the overall listening level of the amplifier 10 0 1 XLR socket for direct injection of the amplifier signal to a mixing desk or additional power amplifier The XLR socket provides a low impedance balanced output signal 11 Ext Speaker This socket s should be used to connect an extension socket cabinet The impedance of the extension
17. lification system in order to prevent a permanent hearing loss if exposure exceeds the limits set forth above To ensure against potentially dangerous exposure to high sound pressure levels it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation Lightning Bolt Symbol Exclamation Mark Symbol This symbol is used to alert the user to the presence A This symbol is used to alert the user to make special note of of dangerous voltages and the possible risk of important operating or maintenance instructions found in the electric shock reference manual SAVE THESE INSTRUCTIONS Lane INTRODUCTION y Congratulations on your decision to purchase a Laney amplifier Laney products are designed with ease of operation as a primary objective hovever to ensure you derive the best from your new amplifier it is important you take time to read this user manual and to familiarise yourself with the control functions and facilities available BEFORE SWITCHING ON After unpacking your amplifier check that it is factory fitted with a three pin grounded or earthed plug Before plugging into the power supply ensure you are connecting to a grounded earth outlet If you should wish to change the factory fitted plug yourself ensure that the viring convention applicable to the count
18. ng the control through to its maximum has the effect of boosting both the low and high frequency content of the signal whilst not effecting the mids 5 Bass Controls the low frequency response of the pre amplifier 6 Lo Paramid frq Selects the LO MID frequencies to be cut or boosted in conjunction with the LO PARAMID LEVEL control 7 To access low LO mid frequencies turn the FREQUENCY control anticlockuise to access higher LO MID frequencies turn the FREQUENCY control clockwise 7 Lo Paramid Level Sets the level of boost or cut applied to the frequency set by control 6 For frequency boost turn the control clockwise For frequency cut turn the control anti clockwise 8 Hi Paramid frq Hi Paramid Frequency Selects the HI MID frequencies to be cut or boosted in conjunction with the Hi PARAMID LEVEL control 9 To access low Hi mid frequencies turn the FREQUENCY control anticlockwise to access higher Hi MID frequencies turn the FREQUENCY control clockuise 9 Lo Paramid Level Sets the level of boost or cut applied to the frequency set by control 8 For frequency boost turn the control clockwise For frequency cut turn the control anti clockwise 10 Treble Controls the high frequency response of the pre amplifier 11 Limiter Allows the on board limiter to be defeated if desired With the switch in the out position the limiter is engaged The limiter is automatically triggered at high output levels and is designed to prevent powe
19. provided Metal parts can be cleaned with a damp cloth The vinyl covering used on some units can be cleaned with a damp cloth or ammonia based household cleaner if necessary Disconnect the unit from the power supply before cleaning Care should be taken so that objects do not fall and liquids are not spilled into the unit through any ventilation holes or openings On no account place drinks on the unit A qualified service technician should check the unit if The power cord has been damaged Anything has fallen or spilled into the unit The unit does not appear to operate correctly The unit has been dropped or the enclosure damaged The user should not attempt to service the equipment All service work is done by a qualified service technician Exposure to extremely high noise levels may cause a permanent hearing loss Individuals vary considerably in susceptibility to noise induced hearing loss but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time The U S Government s Occupational Safety and Health Administration OSHA has specified the following permissible noise level exposure Duration Per Day In Hours Sound Level dBA slow response 90 92 95 97 100 102 105 110 Ya or less 115 According to OSHA any exposure in excess of the above permissible limits could result in some hearing loss Ear plugs or protectors in the ear canals or over the ears must be worn when operating this amp
20. r amp distortion at high output levels When the limiter is autpmatically triggered an LED lights up to indicate the limiter is active It is Possible to have the limiter engaged but not have the LED active The LIMITER monitors both power amp clipping and load so it automatically registers the cabinet impedance and sets itself accordingly 12 Volume Sets the overall listening level of the amplifier 13 Horn switch Switches the on_board horn either on or off 14 D I XLR socket for direct injection of the amplifier signal to a mixing desk or additional power amplifier The XLR socket provides a balanced low impedance output signal Richter Lane 15 Ext Speaker This socket s should be used to connect an extension socket cabinet The impedance of the extension cabinet must not be less thean 8 Ohmsfor the R3 or for the R3H a Minimum 4 Ohms Connecting cabinets that have a lower impedance than 8 Ohms will result in the amplifier overheating Continual use in this manner may cause permanent damage Connecting a cabinet with an impedance of greater than 8 Ohms will cause no damage to the amplifier but will result in a Teduced output y 16 Tuner out Socket for connecting external tuner 17 FX Loop Send and return sockets are provided for connecting external effects units R3H Rear Wi M E o IRA rA TO KERLE THEA OF ELEERI SROLR Do nor REMOVE COVERS NO USER SERVICEABLE PARTS INSIDE REFER iene h QUALIFIED PERSON
21. ry where the amplifier is to be used is strictly conformed to As an example in the United Kingdom the cable colour code for connections are as follous EARTH OR GROUND GREEN YELLOW NEUTRAL BLUE LIVE BROUN This manual has been written for easy access of information The front and rear Panels of each unit are graphically illustrated with each control and feature numbered For a description of the function of each control feature simply check the number with the explanations adjacent to each panel Your Laney RICHTER bass amplifier has undergone a thorough tuo Stage pre delivery inspection involving actual play testing as well as burnin When you first receive your Laney RICHTER bass amp follow these simple procedures i Ensure that the amplifier is set at the correct voltage for the country it is to be used in ii Connect your instrument with a high quality shielded instrument cable Use of cheap cables will compromise the sound of your instrument and your amplifier Care of your Laney amplifier will prolong it s life and yours Lane y RI front u FQUALISA ee Bass AMPLIFIER Norma HiGH 4 3 Q ae AA as e q a 6 R I 1 as 3 T2 2 2 2 r Comp 2 3 wee Cy 8 i 2e 830 q 330 eM pS Sr 8 ie AR ots a 34 gt a 0 10 o 5 100 5k 5 5 0 10 o 0 FREQUENCY Par POWER INPUTS ai ENHANCE EL TREBLE VOLUME D I POWER RY Rear T2AL 115V WARNING TO REDUCE THE RISK OF FIRE OR
Download Pdf Manuals
Related Search