User Manual KVM CAT5 USB Extender Kit
Contents
1. VGA cables to local computer 3 0g 2 USB connectors for keyboard and mouse 2 HDDB15 connectors one for VGA monitor one for Connecting 3 in 1 VGA cables to local computer 1920 x 1440 1280 x 1024 KVM 9006 Receiver Weight g9 3709 13 Appendix B CAT5 Cable Connector Pin Definition Pair 4a Pa r Pair 4 Pair TRTRTRTR 9090699009 _Wire Color Orange 7 Pin 6 EEE ae 6 14 Appendix C CERTIFICATES FCC This equipment has been tested and found to comply with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CE Mark Warning This equipment is in compliance with the requirements of the following regulations EN 55 022 Class RoHS All contents of this package including products packing Materials and documentation comply with RoHS FE CE 152. keyboard and mouse RJ 45 Port for connecting to a CAT5 cable Local Host Port for connecting to the local host via 3 in 1 VGA cable Console Port for connecting to monitor Power Jack for connecting to the power adapter Cable Diagrams 3 in 1 VGA Cable HDDB15 male to one HDDB15 male plus two mini din 6 pin PS 2 connectors PS 2 Keyboard to USB Changer PS 2 keyboard to USB keyboard and mouse changer gt CAT5 5E 6 Straight Through UTP STP Cable CAT5 5E 6 Straight Through Cable Connector 8P8C 3 Hardware Installation 3 1 Installation Diagram It is recommended to power off all the computers and server before the installation If it is difficult to turn off the computers for PS 2 computer connect the Transmitter KVM 9006T and KVM 90086R in the following order first the PS 2 mouse connector followed by PS 2 keyboard connector and then the VGA connector to the computer 1 Refer to the figure below Turn the KVM 9006T KVM 9006R upside down and plaster it with the four accompanied rubber food pads CO 2 Make sure the CAT5 cable is straight through type 3 Plug one end of CAT5 cable into RJ 45 connector of the KVM 9006T and plug the other end of CAT5 cable into RJ 45 port of KVM 9006R 4 Connect keyboard mouse and monitor to the KVM 9006T KVM 9006R console ports USB Keyboard Mouse ports and VGA port 5 Connect local computer to KVM 9006T KVM 9006R with the accompanied 3 in 1 VGA cabl
3. D lt 9 User Manual KVM CATS USB Extender Kit KVM 9006 KVM 9006 Transmitter amp KVM 9006 Receiver Table of Contents t INTRODUCTION see ee 1 1 1 MODEL INFORMATION as es a een essen een lage 1 1 2 FEATURE Son a a a ein Baie bse Eee ne 2 1 3 PACKAGE CONTENTS ee ee 2 2 HARBWARE OVERVIE Wasser 3 2 1 TRANSMITTER S LEDS BUTTON AND PORTS csccesscescescessenccccessenccessesseuccessesseuces 3 2 2 RECEIVER S LEDS BUTTON AND PORTS 2 2 2 Hein 5 3 HARDWARE INSTALLATION en en en en en en en en een 8 3 1 INSTALLATION DJAGRAM 22225322 leh Sa heat Ele 8 3 2 3 IN I VGA GABLE INSTALLATION te ae 9 dA BO ls ee ee lea er 10 4 1 KEYBOARD HOTKEY E ak 10 are 11 APPENDIX A nennen nennen nennen 13 APPENDIX B CAT5 CABLE CONNECTOR PIN DEFINITION 14 APPENDIX C CERTIRICATES 15 1 Introduction The CAT5 USB KVM Extender enables user to access the computer server or KVM switch up to 150 meters away with superior auto adjust RGB gain delay control capability The CAT5 USB Extender is a pair of Transmitter KVM 9006T and Receiver KVM 9006R for high density applications where you want full use of keyboard mouse and monitor but t
4. LEDs Button and Ports Power Status LED os Console Power Status KVM 9006T is power off O KVM 9006T is connected to a computer which is power Power off O KVM 9006T is power on or connected to a computer which is power on m KVM 9006T s RJ 45 port is not connected to the remote site KVM 9006R KVM 9006T is occupied by the remote site KVM 9006R ee Flash KVM 9006R E the VGA signal KVM 90061 is linking with remote when plugging by a CAT5 cable ff On ff n USB Console Ar Console Power Status USB Console Port for connecting to USB type keyboard and mouse RJ 45 Port for connecting to a CAT5 cable Local Host Port for connecting to the local host via 3 in 1 VGA cable Console Port for connecting to monitor Power Jack for connecting to the power adapter Power Jack Console Port RJ 45 Port Local Host Port DC 12V 1A Option RJ45 Console Local Host 2 2 Receiver s LEDs Button and Ports Local Remote LED Sl Console Local Remote The Local port is not selected The Local port is selected and a computer connected to the Local port is power on The Remote port is selected and a computer connected to the Remote port is power on Remote USB Console Local Remote Button Local Remote Power Jack Console Port RJ 45 Port Local Host Port Console Local Host Local Remote Button for selecting local or remote computer USB Console Port for connecting to USB type
5. e see section 3 in 1 VGA Cable Installation for detailed description 3 2 3 in 1 VGA Cable Installation The 3 in 1 VGA cable has a HDDB15 male connector at one end Plug it into the Local Host port of the KVM 9006R The other end of input cable has three connectors a HDDB15 male type for computer video a purple mini din 6 pin PS 2 connector for keyboard and a green mini din 6 pin PS 2 connector for mouse Plug these three connectors into the respective ports of computer PS 2 Computer Plug in PS 2 mouse connector to computer mouse port the PS 2 keyboard connector to computer keyboard port Do not hot plug PS 2 port If you must do that please make sure PS 2 mouse first then the PS 2 keyboard then VGA port USB Computer Connect the PS 2 USB changer to PS 2 keyboard connector and then plug the changer into an available USB port This single USB port can communicate both keyboard and mouse signals It works as a standard HID Human Interface Device no extra driver needed Note that the PS 2 mouse connector should be left disconnected 4 Operations 4 1 Keyboard Hotkey Commands You can switch the KVM 9006R between Local Host port and RJ 45 port through simple key sequences made by the remote console side To send commands to the KVM 9006R you must press the hotkey default is Scroll Lock twice within 2 seconds You will hear a beep sound confirming you are in the hotkey mode Then you have to
6. enter command in 2 seconds If you do not press any key during hotkey mode over 2 seconds the hotkey mode will be terminated and back to normal state Example Default Hotkey Scroll Lock Tseron f Tseron f Lock Lock Switch between Local and Remote Site The table below lists all the supported hotkey commands To switch between Local and Remote ports Q T turn the beep sound on or off To activate the Auto Scan function Auto scan Remote and Local port every 8 seconds repeatedly A For auto adjust video signal of remote port to optimum 10 5 Troubleshooting Make sure that all cables are well seated Label all cables with the name number for each respective computer to avoid confusion Q KVM 9006 Transmitter or KVM 9006R s LED is not ON Make sure the computer connected to KVM 9006T or KVM 9006R is power on Make sure the cable connected to KVM 9006T or KVM 9006R is well seated Q No video signal is displayed on the monitor Make sure the power adapter is connected to the KVM 9006R Make sure the VGA cable and CAT5 cable are properly connected to the connectors Make sure the VGA cable is attached to computer before the boot up process Q The computer has started up but keyboard or mouse doesn t work Make sure your keyboard and mouse work fine if directly plugged into the computer PS 2 Computer Keyboard and mouse are not hot pluggable Make sure the PS 2 cables are well co
7. here is no room for a server nearby Or for applications where you want to put all computers in a safe place all the users only have keyboard mouse and monitor on their desk The Transmitter KVM 9006T allows you to locate your console keyboard mouse and monitor to a suitable control field conveniently over existing network construction You need just install a pair of extender the Transmitter and the Receiver at local side and remote side individually It also saves your cable layout and cable installation cost KVM 9006R allows you to control remote computer system 150 meters away while working on local computer 1 1 Model Information Transmitter Box KVM 9006T with USB Local Console Receiver Box KVM 9006R with USB Local Console support 150 meters 9 2 Features Compact box design Locate CAT5 console up to 150 meters Collocate computers and servers on one location ideal for hazardous or unsecured environments Switch computers by push button or hotkey commands Audible feedback when switching LED indicators for computer status or data transmission Work with PS 2 or USB computer Easy to install and use with plug and play functionality 3 Package Contents 1 x KVM 9006T 1 x KVM 9006R 2 x KVM 3 in 1 Cable 2 x USB Changer 1 x User Manual 1 x DC12V 1A AC to DC Power Adapter for KVM 9006T 1 x DC12V 1A AC to DC Power Adapter for KVM 9006R 8 x Footpad 2 Hardware Overview 2 1 Transmitter s
8. nnected then reboot the computer USB Computer Unplug and plug in the USB connector wait few seconds for USB bus emulations and start up process to complete Do not press any keys on keyboard while the selected computer is booting up Otherwise it might cause keyboard error or keyboard is not detected by the Host side Try a different keyboard but use only 101 102 104 key keyboard 11 Q Video signal is foggy or un cleared on the screen Make sure the VGA cable is properly connected There are various CAT5 cables such as CAT5 CAT5E CAT6 and STP UTP types If your application need long distance with high VGA resolution please select higher quality cables Make sure the VGA resolution is not too high for the length of cable that is used It is highly recommended to use optimal CAT5 cable length to obtain the best video quality while still saving the redundant cable length Therefore if the problem remained please Shorten the CAT5 cable length or reduce VGA resolution Q There is an error message Keyboard or Mouse not found on the screen Please make sure USB or PS 2 connectors are well seated Q How to use the KVM CATS5 Extender with an USB interface computer such as PC MAC or SUN Microsystems Please plug PS 2 USB changer to change a PS 2 connector to a USB connector 12 Appendix A Specifications KVM 9006 Transmitter 2 HDDB15 connectors one for VGA monitor one for Connecting 3 in 1
Download Pdf Manuals
Related Search