Home

The LEON Processor User`s Manual

1. Figure 32 LEON configuration register 25 UMAC SMAC instruction implemented 24 20 Number of register windows The implemented number of SPARC register windows 1 19 17 gicsz QILSZ Instruction cache size The size in Kbytes of the instruction cache Cache size 16 15 Instruction cache line size The line size in 32 bit words of each line Line size 14 12 Data cache size The size in kbytes of the data cache Cache size 2DCSZ e 11 10 Data cache line size The line size in 32 bit words of each line Line size 2PLSZ 9 UDIV SDIV instruction implemented 8 UMUL SMUL instruction implemented 6 Memory status and failing address register present 5 4 FPU type 00 none 01 Meiko PCI core type 00 none 01 InSilicon 10 ESA 1 1 other 5 4 3 2 1 0 Write protection type 00 none 01 standard Gaisler Research 37 LEON user s manual 5 8 Power down The processor can be powered down by writing an arbitrary value to the power down register Power down mode will be entered on the next load or store instruction To enter power down mode immediately two consecutive stores to the power down register should be performed During power down mode the integer unit will effectively be halted The power down mode will be terminated and the integer unit re enabled when an unmasked interrupt with higher level than the current processor i
2. Table 10 Memory bus signals 7 2 System interface signals Name Type Function Active CLK Input System clock ERRORN Open drain System error High PIO 15 0 Bidir Parallel I O port RESETN Input System reset WDOGN Open drain Watchdog output Table 11 System interface signals Gaisler Research 46 LEON user s manual 7 3 Signal description A 30 0 Address bus output These active high outputs carry the address during accesses on the memory bus When no access 1s performed the address of the last access is driven also internal cycles BEXCN Bus exception input This active low input is sampled simultaneously with the data during accesses on the memory bus If asserted a memory error will be generated BRDYN Bus ready input This active low input indicates that the access to a memory mapped I O area can be terminated on the next rising clock edge D 31 0 Data bus bi directional D 31 0 carries the data during transfers on the memory bus The processor only drives the bus during write cycles During accesses to 8 bit areas only D 31 24 are used IOSN I O select output This active low output is the chip select signal for the memory mapped I O area OEN Output enable output This active low output is asserted during read cycles on the memory bus ROMSN 1 0 PROM chip select output These active low outputs provide the chip
3. Gaisler Research 7 LEON user s manual 1 6 Functional overview A block diagram of LEON can be seen in figure 1 LEON processor LEON SPARC Integer unit El Co proc User 1 0 e gt I Cache D Cache AMBA AHB AHB Controller Timers IrqCtrl AHB APB Bridge UARTS I O port Memory Controller 8 16 32 bits memory bus PROM SRAM 1 0 Figure 1 LEON block diagram AMBA APB LLL 1 6 1 Integer unit The LEON integer unit implements the full SPARC V8 standard including all multiply and divide instructions The number of register windows is configurable within the limit of the SPARC standard 2 32 with a default setting of 8 1 6 2 Floating point unit and co processor The LEON model does not include an FPU but provides a direct interface to the Meiko FPU core and a general interface to connect other floating point units A generic co processor interface is provided to allow interfacing of custom co processors 1 6 3 Cache sub system Separate instruction and data caches are provided each configurable to 1 64 kbyte with 8 32 bytes per line Sub blocking is implemented with one valid bit per 32 bit word The caches uses streaming during line refill to minimise refill latency The data cache uses write through policy and implements a double word write buffer Gaisler Research 8 LEON user s manual 1 6 4 Memory interface
4. where the selection is done depending on the configured synthesis method and target technology To port to a new tool or target library a technology dependant package should be added exporting the proper cell generators In the TARGET package the targettechs type should be updated to include the new technology or synthesis tool while the TECH_MAP package should be edited to call the exported cell generators for the appropriate configuration 12 2 Target specific mega cells 12 2 1 Register file The register file should have one synchronous write port and two synchronous or asynchronous read ports The data width is 32 bits while the number of registers depend on the configured number of register windows The standard configuration of 8 windows requires 136 registers numbered 0 135 Note that register 128 is not used and will never be written corresponds to SPARC register g0 If the register file has synchronous read ports the RFSYNCRD field should be set to true in the processor configuration record If the Meiko FPU is enabled using the direct interface the register file should have 32 extra registers to store the FPU registers i e 168 registers for 8 register windows FPU For all target technologies FPGA and ASIC the register file is currently implemented as two parallel dual port rams each one with one read port and one write port For register file implementations using asynchronous read ports bypass logic must be inserted
5. 1t was enabled but no new lines are allocated on read misses 31 17 16 15 14 543210 RESERVED IB IP DP RESERVED DF IF DCS ICS Figure 7 Cache control register Field Definitions e 31 17 Reserved e 16 Instruction burst fetch IB This bit enables burst fill during instruction fetch 15 Instruction cache flush pending IP This bit is set when an instruction cache flush operation is in progress e 14 Data cache flush pending DP This bit is set when an data cache flush operation is in progress e 5 Data Cache Freeze on Interrupt DF If set the data cache will automatically be frozen when an asynchronous interrupt is taken e 4 Instruction Cache Freeze on Interrupt IF If set the instruction cache will automatically be frozen when an asynchronous interrupt is taken e 3 2 Data Cache state DCS Indicates the current data cache state according to the following X0 disabled 01 frozen 11 enabled e 1 0 Instruction Cache state ICS Indicates the current data cache state according to the following X0 disabled 01 frozen 11 enabled If the DF or IF bit is set the corresponding cache will be frozen when an asynchronous interrupt is taken This can be beneficial in real time system to allow a more accurate Gaisler Research 20 LEON user s manual calculation of worst case execution time for a code segment The execution of the interrupt handler will not evi
6. 4 3 AHB slave inputs HCLK and HRESETn routed separately type AHB_Slv_lIn_ Type is record HSEL Std_ULogic slave select HADDR Std_Logic_Vector HAMAX 1 downto 0 address bus byte HWRITE Std_ULogic read write HTRANS Std_Logic_Vector 1 downto 0 transfer type HSIZE Std_Logic_Vector 2 downto 0 transfer size HBURST Std_Logic_Vector 2 downto 0 burst type HWDATA Std_Logic_Vector HDMAX 1 downto 0 write data bus HPROT Std_Logic_Vector 3 downto 0 protection control HREADY Std_ULogic transfer done HMASTER Std_Logic_Vector 3 downto 0 current master HMASTLOCK Std_ULogic locked access end record AHB slave outputs type AHB_Slv_Out_Type is record HREADY Std_ULogic transfer done HRESP Std_Logic_Vector 1 downto 0 response typ HRDATA std_Logic_Vector HDMAX 1 downto 0 read data bus HSPLIT Std_Logic_Vector 15 downto 0 split completion end record The AHB controller AHBARB controls the AHB bus and implements both bus decoder multiplexer and the bus arbiter The arbitration scheme is fixed priority where the bus master with highest index has highest priority The processor is by default put on the lowest index Note to be granted the bus a master must drive both the request signal and a valid i e non idle transfer type on HTRANS APB bus The APB bridge is connected to the AHB bus as a s
7. 5 5 3 5 5 4 5 5 5 5 5 6 5 6 5 7 5 8 6 6 1 6 2 6 3 6 4 6 5 6 6 6 7 6 7 1 6 7 2 6 8 7 7 1 7 2 7 3 8 8 1 8 2 8 3 AHB DIS A ad 21 APB Dis as een dal E N AE SET easduon sea EEE 22 A A E E E E EE Oe R 22 AHB cache A O O a A EE ai 23 On chip pr O eens n 24 On chip register S cisnienia n RR 24 Interrupt controleT rcr i A dees E RE aS 25 OperatON asee evades seen E aa A EE E E E EE EKES EE EET 25 A O E EEE 26 Controlre sisters nrin a a a N A A EE E aN 26 Secondary interrupt controller ssseesseeeesseesseesseesseeesseessseesseesseesssressseesseese 28 OP OM iaa 28 Control register iii ida diaa Eo E 29 A EN 30 A E EEEE EE aay ate ena ta toate eo aus T 30 RS US GSTS Ac 31 OS 32 Transmitter Opera diia sides 32 RECEIVER OP ELALOMS td 33 Bavid rate SEneration airis diri iras riada atea 33 Loop Dack moden ON 33 ao A ae a R E aa 34 HART ts do 34 Parallel VO PO dd II AA duane iO ia 35 LEON configuration Te Sister ici tiraera tanda dde daran deben 36 POW OWI toa daa 37 External Menor acces O 38 Memory interface e dat 38 MEMO COM A ated naa ea Schnee easton 38 RANE ACCESS uss O syseec4 isa ION 39 PROM CCESS ivan iia aE ocean 40 Memory mapped Oia 40 BUSES daa 41 8 bit and 16 bit memory configuration ccoooccnoncccnoncccnoncnonnnnncnoncnonnnnncnnncnonnnnno 41 Memory configuration register Li a ee ea 42 Memory configuration register 2 5 235 cs2assceseceesausccd sxassdaaeaceanacsedendeeeanccedanece ses 43 WW T
8. RESERVED TIMER RELOAD VALUE Figure 21 Timer 1 2 reload registers 31 3 2 1 0 RESERVED LD RL EN Figure 22 Timer 1 2 control registers e 2 Load counter LD when written with one will load the timer reload register into the timer counter register Always reads as a zero 1 Reload counter RL if RL is set then the counter will automatically be reloaded with the reload value after each underflow 0 Enable EN enables the timer when set 31 RESERVED RELOAD VALUE Figure 23 Prescaler reload register 31 RESERVED COUNTER VALUE Figure 24 Prescaler counter register Gaisler Research 32 LEON user s manual 5 5 UARTs Two identical UARTs are provided for serial communications The UARTs support data frames with 8 data bits one optional parity bit and one stop bit To generate the bit rate each UART has a programmable 12 bits clock divider Hardware flow control is supported through the RTSN CTSN hand shake signals Figure 25 shows a block diagram of a UART CTSN Serial port Baud rate 8 bitcik Controller RTSN generator RXD K Receiver shift register k gt Transmitter shift register gt TXD Receiver holding register Transmit holding register Internal I O Bus Figure 25 UART block diagram 5 5 1 Transmitter operation The transmitter is enabled through the TE bit in the UART control register
9. 31 16 15 1 0 RESERVED IPEND 15 1 R Figure 11 Interrupt pending register Field Definitions e 15 1 Interrupt pending IPEND 15 1 indicates whether an interrupt is pending IPEND n 1 e 31 16 0 Reserved 31 16 15 1 0 RESERVED IFORCE 15 1 Figure 12 Interrupt force register Field Definitions e 15 1 Interrupt force IFORCE 15 1 indicates whether an interrupt is being forced IFORCE n 1 e 31 16 0 Reserved 31 16 15 1 0 RESERVED ICLEAR 15 1 R Figure 13 Interrupt clear register Field Definitions e 15 1 Interrupt clear ICLEAR 15 1 if written with a 1 will clear the corresponding bit s in the interrupt pending register A read returns zero e 31 16 0 Reserved Gaisler Research 28 LEON user s manual 5 3 Secondary interrupt controller The optional secondary interrupt controller is used add up to 32 additional interrupts to be used by on chip units in system on chip designs Figure 9 shows a block diagram of the interrupt controller IRQ Pending Priority encoder 32 Filtering 32 5 IRQ 31 0 IRL 4 0 IRQIO IRQ mask E Figure 14 Secondary interrupt controller block diagram 5 3 1 Operation The incoming interrupt signals are filtered according to the setting in the configuration record The filtering condition can be one of four active low active high negative edge tri
10. When ready to transmit data is transferred from the transmitter holding register to the transmitter shift register and converted to a serial stream on the transmitter serial output pin TXD It automatically sends a start bit followed by eight data bits an optional parity bit and one stop bits figure 26 The least significant bit of the data is sent first Data frame no parity Start Do D1 D2 D3 D4 D5 De D7 Stop Data frame with parity Start Do D1 D2 D3 D4 D5 D6 D7 Parity Stop Figure 26 UART data frames Following the transmission of the stop bit if a new character is not available in the transmitter holding register the transmitter serial data output remains high and the transmitter shift register empty bit TSRE will be set in the UART control register Transmission resumes and the TSRE is cleared when a new character is loaded in the transmitter holding register If the Gaisler Research 33 LEON user s manual transmitter is disabled it will continue operating until the character currently being transmitted is completely sent out The transmitter holding register cannot be loaded when the transmitter is disabled If flow control is enabled the CTSN input must be low in order for the character to be transmitted If it is deasserted in the middle of a transmission the character in the shift register is transmitted and the transm
11. code pragma translate_on This works with most synthesis tools although in Synopsys requires the hdlin_translate_off_skip_text variable be set to true 11 2 Synthesis procedure Synthesis should be done from the syn directory It includes scripts project files for Synplify Synopsys DC Synopsys FC2 and Leonardo The source files are read from the leon directory so it is essential that the configuration in the TARGET and DEVICE packages is correct To simplify the synthesis procedure a number of pre defined configuration are provided in the TARGET package The selection of the active configuration is done in the DEVICE package The following table shows the characteristics of some of the pre defined configurations Configuration cache regfile mul div rom pads target syntool fpga_2k2k inferred inferred none none inferred any synp leo fpga_2k2k_softprom inferred inferred none inferred inferred any synp leo fpga_2k2k_v8_softprom inferred inferred inferred inferred inferred any synp leo virtex_2k2k_blockprom inferred instance none instance inferred virtex any virtex_2k2k_v8_blockprom inferred instance inferred instance inferred virtex any gen_atc25 instance instance instance none instance ATC25 any gen_atc35 instance instance instance none instance ATC35 any gen_fs90 instance instance instance none instance FS90AB any Table 15 Some pre defined sy
12. later can be used the earlier 2000 x versions have bugs in type resolution functions and will fail during analysis of the model Leonardo is capable of automatically inferring the necessary ram cells for register file and caches Gaisler Research 63 LEON user s manual 12 Porting to a new technology or synthesis tool 12 1 General LEON uses three types of technology dependant cells rams for the cache memories 3 port register file for the IU FPU registers and pads These cells can either be inferred by the synthesis tool or directly instantiated from a target specific library For each technology or instantiation method a specific package is provided The selection of instantiation method and target library is done through the configuration record in the TARGET package The following technology dependant packages are provided package Function Instantiation method TECH_GENERIC Behavioural models inferred TECH_VIRTEX Generators for Xilinx VIRTEX direct instantiated TECH_ATC25 Generators for Atmel ATC25 direct instantiated TECH_ATC35 Generators for Atmel ATC35 direct instantiated TECH_FS90 Generators for UMC FS90A B direct instantiated TECH_MAP Selects mega cells depending on configuration Table 17 Register file connections The technology dependant packages can be seen a wrappers around the mega cells provided by the target technology or synthesis tool The wrappers are then called from TECH_MAP
13. or to use direct instantiation The choice is done by setting the parameters infer_ram infer_regf and infer_rom accordingly The rfsynerd option has impact on target technologies which are capable of providing a register file with both asynchronous and synchronous read ports Currently this is only used when infer_regf is true and the synthesis tool infers the register file Infer_mult selects how the multiplier is generated for details see section 9 2 below Gaisler Research 51 LEON user s manual 9 2 Integer unit configuration The integer unit configuration record is used to control the implementation of the integer unit integer unit configuration type multypes is none iterative m32x8 ml16x16 m32x16 m32x32 type divtypes is none radix2 type iu_config_type is record nwindows integer register windows 2 32 multiplier multypes multiplier type divider divtypes divider typ mac boolean multiply accumulate fpuen integer range 0 to 1 FPU enable cpen boolean co processor enabl fast jump boolean enable fast jump address generation icchold boolean enable fast branch logic lddelay integer range 1 to 2 load delay cycles 1 2 fastdecode boolean optimise instruction decoding FPGA only watchpoints integer range 0 to 4 hardware watchpoints 0 4 impl integer range 0 to 15 IU implementation ID version integer range 0 to 15 IU version ID end reco
14. output This active low output is asserted when the watchdog times out Gaisler Research 48 LEON user s manual 8 VHDL model architecture 8 1 Model hierarchy The LEON VHDL model hierarchy can be seen in table 12 below Entity Package File name Function LEON leon vhd LEON top level entity LEON_PCI leon_pci vhd LEON PCI top level entity LEON MCORE mcore vhd Main core LEON MCORE CLKGEN clkgen vhd Clock generator LEON MCORE RSTGEN rstgen vhd Reset generator LEON MCORE AHBARB ahbarb vhd AMBA ABB controller LEON MCORE APBMST apbmst vhd AMBA APB controller LEON MCORE MCTRL mctrl vhd Memory controller LEON MCORE MCTRL BPROM bprom vhd Internal boot prom LEON MCORE PROC proc vhd Processor core LEON MCORE PROC CACHE cache vhd Cache module LEON MCORE PROC CACHE CACHEMEM cachemem vhd Cache ram LEON MCORE PROC CACHE DCACHE dcache vhd Data cache controller LEON MCORE PROC CACHE ICACHE icache vhd Instruction cache controller LEON MCORE PROC CACHE ACACHE acache vhd AHB cache interface module LEON MCORE PROC IU iu vhd Processor integer unit LEON MCORE PROC MUL mul vhd Multiplier state machined LEON MCORE PROC DIV div vhd radix 2 divider LEON MCORE PROC FP1EU fpleu vhd parallel FPU interface LEON MCORE PROC REGFILE regfile vhd Processor register file LEON MCORE IRQCTRL irqctrl vhd Interrupt controller LEON MCORE IOPORT ioport vhd Parallel I O port LEON MCORE TIMERS timers vhd Timers and watchdo
15. the prescaler underflows it is reloaded from the prescaler reload register and a timer tick is generated for the two timers and watchdog The effective division rate is therefore equal to prescaler reload register value 1 The operation of the timers is controlled through the timer control register A timer is enabled by setting the enable bit in the control register The timer value is then decremented each time the prescaler generates a timer tick When a timer underflows it will automatically be reloaded with the value of the timer reload register if the reload bit is set otherwise it will stop at Oxffffff and reset the enable bit An interrupt will be generated after each underflow The timer can be reloaded with the value in the reload register at any time by writing a one to the load bit in the control register The watchdog operates similar to the timers with the difference that it is always enabled and upon underflow asserts the external signal WDOG This signal can be used to generate a system reset To minimise complexity the two timers and watchdog share the same decrementer This means that the minimum allowed prescaler division factor is 4 reload register 3 Gaisler Research 31 LEON user s manual 5 4 2 Registers Figures 20 to 23 shows the layout of the timer unit registers 31 24 23 0 RESERVED TIMER WATCHDOG VALUE Figure 20 Timer 1 2 and Watchdog counter registers 31 24 23 0
16. to bypass write data in case of read write contention read and write to the same Gaisler Research 64 LEON user s manual address The timing and behaviour of the read ports during read write contention can then be ignored For synchronous register files reading and writing is done on the falling edge of the clock and the standard bypass logic is sufficient to bypass read write conflicts Also in this case the timing and behaviour of the read port during read write contention can be ignored The TECH_ATC25 contains an example on a register file with asynchronous read ports while TECH_ATC35 uses synchronous read ports 12 2 2 Cache ram memory cells Synchronous single port ram cells are used for both tag and data in the cache The width and depth depends on the configuration as defined in the configuration record The table below shows the ram size for certain cache configurations Cache size Words line tag ram data ram 1 kbyte 8 32x30 256x32 1 kbyte 4 64x26 256x32 2 kbyte 8 64x29 512x32 2 kbyte 4 128x25 512x32 4 kbyte 8 128x28 1024x32 4 kbyte 4 256x24 1024x32 8 kbyte 8 256x27 2048x32 8 kbyte 4 512x23 2048x32 16 kbyte 8 512x26 4096x32 16 kbyte 4 1024x22 4096x32 Table 18 Cache ram cell sizes The cache controllers are designed such that the used ram cells do NOT have to support write through simultaneous read of written data 12 2 3 Pads Technology specific pads are usually aut
17. true interrupt ctrl 0x90 0x9C 0010100000 0010101100 9 true I O port OxA0 OxAC others gt apb_slv_config_void type apb_config_type is record table apb_slv_config_vector 0 to APB_SLV_MAX 1 end record constant apb_std apb_config_type table gt apbslvcfg_std The table is used to automatically configure the AHB APB bridge To add APB slaves edit the slave configuration table and add your modules in MCORE The APB slaves should be connected to the apbi apbo buses The index field in the table indicates which bus index the slave should connect to Gaisler Research 58 LEON user s manual 10 Simulation 10 1 Un packing the tar file The model is distributed as a gzipped tar file leon 2 x x tar gz On unix systems use the command gunzip c leon 2 x x tar gz tar xf to unpack the model in the current directory The LEON model has the following directory structure leon top directory leon Makefile top level makefile leon leon LEON vhdl model leon modelsim Modelsim simulator support files leon pmon Boot monitor leon syn Synthesis support files leon tbench LEON VHDL test bench leon tsource LEON test bench C source 10 2 Compilation of the model On unix systems or MS windows with cygwin installed the LEON VHDL model and test bench can be built using make in the top directory Doing make without a target or make all will build the model and test benches using the m
18. 3 2 sub block Note that diagnostic access to the cache is not possible during a FLUSH operation and will cause a data exception trap 0x09 if attempted 3 1 4 Instruction cache tag A instruction cache tag entry consists of several fields as shown in figure 5 31 10 9 8 7 0 ATAG 00 VALID Figure 5 Instruction cache tag layout Field Definitions e 30 10 Address Tag ATAG Contains the tag address of the cache line e 7 0 Valid V When set the corresponding sub block of the cache line contains valid data These bits is set when a sub block is filled due to a successful cache miss a cache fill which results in a memory error will leave the valid bit unset A FLUSH instruction will clear all valid bits V O corresponds to address 0 in the cache line V 1 to address 1 V 2 to address 2 and so on NOTE only the necessary bits will be implemented in the cache tag depending on the cache configuration As an example a 2 kbyte cache with 32 bytes per line would only have eight valid bits and 21 tag bits The cache rams are sized automatically by the ram generators in the model Data cache 3 2 1 Operation The LEON data cache is a direct mapped cache configurable to 1 64 kbyte The write policy for stores is write through with no allocate on write miss The data cache is divided into cache lines of 8 32 bytes Each line has a cache tag associated with it containing a tag field and one valid bit per 4 by
19. 3 2 Control registers The operation of the interrupt controller is programmed through the following registers 31 0 IMASK 31 0 Figure 15 Interrupt mask register e 31 0 Interrupt mask indicates whether an interrupt is masked IMASK n 0 or enabled IMASK n 1 31 0 IPEND 31 0 Figure 16 Interrupt pending register e 31 0 Interrupt pending indicates whether an interrupt is pending PEND n 1 31 5 4 0 RESERVED I IRL 4 0 az Figure 17 Interrupt status register e 4 0 Interrupt request level indicates the highest unmasked pending interrupt e 5 Interrupt pending if set then IRL is valid If cleared no unmasked interrupt is pending 31 0 ICLEAR 31 0 Figure 18 Interrupt clear register e 31 0 Interrupt clear if written with a 1 will clear the corresponding bit s in the interrupt pending register Gaisler Research 30 LEON user s manual 5 4 Timer unit The timer unit implements two 24 bit timers one 24 bit watchdog and one 10 bit shared prescaler figure 19 timer1 reload prescaler reload timer2 reload el timer1 value gt irq 8 prescaler value timer2 value gt irq 9 watchdog gt WDOG Y 1 Figure 19 Timer unit block diagram 5 4 1 Operation The prescaler is clocked by the system clock and decremented on each clock cycle When
20. Gaisler Research 25 LEON user s manual 5 2 Interrupt controller The LEON interrupt controller is used to prioritize and propagate interrupt requests from internal or external devices to the integer unit In total 15 interrupts are handled divided on two priority levels Figure 9 shows a block diagram of the interrupt controller IRQ Pending T Oo PER_IRQ 7 0 gt Priority 4 encoder PCI_IRQ 3 0 gt 4 Irq amp trig 4 PIO 15 0 select E IRL 3 0 IR IRQ Priority ne mask select E Figure 9 Interrupt controller block diagram 5 2 1 Operation When an interrupt is generated the corresponding bit is set in the interrupt pending register The pending bits are ANDed with the interrupt mask register and then forwarded to the priority selector Each interrupt can be assigned to one of two levels as programmed in the interrupt level register Level 1 has higher priority than level 0 The interrupts are prioritised within each level with interrupt 15 having the highest priority and interrupt 1 the lowest The highest interrupt from level 1 will be forwarded to the IU if no unmasked pending interrupt exists on level 1 then the highest unmasked interrupt from level O will be forwarded When the IU acknowledges the interrupt the corresponding pending bit will automatically be cleared Interrupt can also be forced by setting a bit in the interrupt force register In this case the I
21. ILEY FOLG A O ER A A 43 NN 45 Memory Bug al tico 45 Systeminterface SIGNALS A 45 O 46 VHDL model architectiite ni iia 48 Model erareh Yidis AAEE aE A Ea iA 48 Model coding Styles ii boi 49 Clocking scheme A E N A AN 49 Gaisler Research 5 LEON user s manual 9 1 9 2 9 3 9 4 9 5 9 6 9 7 9 7 1 9 7 2 9 7 3 9 8 9 8 1 9 8 2 9 8 3 9 8 4 10 10 1 10 2 10 3 10 4 10 5 10 6 10 6 1 10 6 2 10 7 11 11 1 11 2 11 2 1 11 2 2 11 2 3 11 2 4 12 12 1 12 2 12 2 1 12 22 12 2 3 12 2 4 Model COn Urantia 50 Synthesis configuration sti pass 50 Integer nit configuration onn AA A ia 51 Cache confirur tion lo Ra 52 Memory controller confguratiolsrraniii ii a 52 Deb g CON ASUS aria e ia 52 Peripheral configuration vv seacecsadesdacessuside susedecatasuadaads deeccdeantesdaawades 53 BORNEO UA de a do de 54 Booting from MEN LP aaa 54 PMON S record Lt eii id A AA ee 54 RADMOR ee atonien tect a E tetas stanton E IREN 55 AMBA configuration sseseeeeeseeeesseessresserssereseeeessresseesseeeseeeeseeesseessersseeeseeee 55 AHB master configuration tii 55 AHB slave CONT UTA OM escroto nrnesneneiinii ini eii 56 AHB cachability configuration sssessesssesssesesseeessressessseresseeesseessesseesseeeeseee 56 APB confisuration dia 56 Sinulat gi AAA e O 58 Un packing the tar Fle iria is 58 Compilation ot the Mode idilio 58 Generic test bench cesan di da ie 58 Des o soe 59 A A 59 Simulator specific support nateni ele e
22. The LEON Processor User s Manual Version 2 3 5 July 2001 Chore Hani WET Jiri Gaisler Gaisler Research 2 The LEON processor user s manual Gaisler Research jiri gaisler com TheLEON processor user s manual Copyright 2001 Gaisler Research Permission is granted tomakeand distribute verbatim copies of this manual provided the copyright notice and this permission notice are preserved on all copies Permission is granted to copy and distribute modified versions of this manual under the conditions for verbatim copying provided also that the entire resulting derived work is distributed under the terms of a permission notice identical to this one Permission is granted to copy and distribute translations of this manual into another language un der the above conditions for modified versions Gaisler Research 3 LEON user s manual 1 1 1 2 1 3 1 4 1 5 1 6 1 6 1 1 6 2 1 6 3 1 6 4 1 6 5 1 6 6 1 6 7 1 6 8 1 6 9 1 6 10 1 6 11 1 6 12 2 1 2d 2 3 2 4 2 3 2 6 2 7 2 8 2 9 2 10 2 11 3 1 3 1 1 3 1 2 3 1 3 3 1 4 3 2 3 2 1 3 2 2 3 2 3 3 2 4 3 2 3 3 2 6 3 3 A a ec a a aE iiei 6 OVERVIEW ari shane IN sevecaniaee iatoes Hi sdeaed appease 6 PST AGRI BAECS 532s egy Si SOS 6 News in LEON 1 Version ss it 6 CASA ios 6 Fault tolerant LEON LEON FT coccccccnnnonononononononnononnnnnnononcnnononnnnnnononononnons 6 Eunectional OvervieW ausen di leida aE 7 A E tac 2k sues te 8 a asta she
23. The memory interface provides a direct interface PROM SRAM and memory mapped I O devices The memory areas can be programmed to either 8 16 or 32 bit data width 1 6 5 Timers Two 24 bit timers are provided on chip The timers can work in periodic or one shot mode Both timers are clocked by a common 10 bit prescaler 1 6 6 Watchdog A 24 bit watchdog is provided on chip The watchdog is clocked by the timer prescaler When the watchdog reaches zero an output signal WDOG is asserted This signal can be used to generate system reset 1 6 7 UARTs Two 8 bit UARTs are provided on chip The baud rate is individually programmable and data is sent in 8 bits frames with one stop bit Optionally one parity bit can be generated and checked 1 6 8 Interrupt controller The interrupt controller manages a total of 15 interrupts originating from internal and external sources Each interrupt can be programmed to one of two levels A chained secondary controller for up to 32 extra interrupts is also available 1 6 9 Parallel I O port A 16 bit parallel I O port is provided Each bit can be programmed to be an input or an output Some of the bits have alternate usage such as UART inputs outputs and external interrupts inputs 1 6 10 AMBA on chip buses The processor has a full implementation of AMBA AHB and APB on chip buses A flexible configuration scheme makes it simple to add new IP cores Also all provided peripheral units implement
24. U acknowledgement will clear the force bit rather than the pending bit After reset the interrupt mask register is set to all zeros while the remaining control registers are undefined Interrupts 10 15 are unused by the default configuration of LEON and can be use by added IP cores Note that interrupt 15 cannot be maskable by the integer unit and should be used with care most operating system do safely handle this interrupt Gaisler Research 5 2 2 Interrupt assignment 26 Table 7 shows the assignment of interrupts Interrupt Source 15 user defined 14 user defined PCI 13 user defined 12 user defined 11 user defined 10 user defined 9 Timer 2 8 Timer 1 7 Parallel I O 3 6 Parallel I O 2 5 Parallel I O 1 4 Parallel 1 O 0 3 UART 1 2 UART 2 1 AHB error Table 7 Interrupt assignments 5 2 3 Control registers LEON user s manual The operation of the interrupt controller is programmed through the following registers Field Definitions 31 17 16 15 ILEVEL 15 1 R IMASK 15 1 Figure 10 Interrupt mask and priority register 31 17 Interrupt level LEVEL 15 1 indicates whether an interrupt belongs to priority level 1 ILEVELT n 1 or level 0 LEVEL n 0 15 1 Interrupt mask IMASK 15 0 indicates whether an interrupt is masked MASK n 0 or enabled IMASK n 1 16 0 Reserved Gaisler Research 27 LEON user s manual
25. binary steps from 8 Kbyte to 256 Mbyte A read access to static RAM consists of two data cycles and between zero and three waitstates On non consecutive accesses a lead out cycle is added after a read cycle to prevent bus contention due to slow turn off time of memories or I O devices Figure 34 shows the basic read cycle waveform zero waitstate datal data2 lead out A RAMSN RAMOEN D Figure 34 Static ram read cycle For read accesses a separate output enable signal RAMOEN n is provided for each RAM bank and only asserted when that bank is selected If you use memory modules with several banks but a common output enable use the OEN signal instead which is asserted on any read cycle A write access is similar to the read access but has takes a minimum of three cycles lead in lead out CLK RAMSN RWEN Figure 35 Static ram write cycle Through a feed back loop from the write strobes the data bus is guaranteed to be driven until the write strobes are de asserted Each byte lane has an individual write strobe to allow efficient byte and half word writes If you memory used a common write strobe for the full 16 or 32 bit data set the read modify write bit MCR2 which will enable read modify write cycles for sub word writes Gaisler Research 40 LEON user s manual 6 4 PROM access Accesses to prom have the same timing as RAM accesses the differences being that PROM cycles can have up to 15 wait
26. ch illegal_instruction 0x02 3 UNIMP or other un implemented instruction privileged_instruction 0x03 4 Execution of privileged instruction in user mode fp_disabled 0x04 6 FP instruction while FPU disabled cp_disabled 0x24 6 CP instruction while Co processor disabled watchpoint_detected 0x0B 7 Instruction or data watchpoint match window_overflow 0x05 8 SAVE into invalid window window_underflow 0x06 8 RESTORE into invalid window register_hadrware_error 0x20 9 register file EDAC error LEON FT only mem_address_not_aligned 0x07 10 Memory access to un aligned address fp_exception 0x08 11 FPU exception cp_exception 0x28 11 Co processor exception data_access_exception 0x09 13 Access error during load or store instruction Table 3 Trap allocation and priority Gaisler Research 13 LEON user s manual Trap TT Pri Description tag_overflow Ox0A 14 Tagged arithmetic overflow divide_exception 0x2A 15 Divide by zero interrupt_level_1 0x11 31 Asynchronous interrupt 1 interrupt_level_2 0x12 30 Asynchronous interrupt 2 interrupt_level_3 0x13 29 Asynchronous interrupt 3 interrupt_level_4 0x14 28 Asynchronous interrupt 4 interrupt_level_5 0x15 27 Asynchronous interrupt 5 interrupt_level_6 0x16 26 Asynchronous interrupt 6 interrupt_level_7 0x17 25 Asynchronous interrupt 7 interrupt_level_8 0x18 24 Asynchronous interrupt 8 interrupt_level_9 0x19 23 Asynchronous interrupt 9 interru
27. ch address generation fastjump can be set to implement a separate branch address adder The pipeline can be configured to have either one or two load delay cycles using the Iddelay option One cycle gives higher performance lower CPI but may result in slower timing in ASIC implementations In FPGA implementations setting icchold will improve timing by adding a pipeline hold cycle if a branch instruction is preceded by an icc modifying instruction Similarly fastdecode will improve timing by adding parallel logic for register file address generation Setting watchpoint to a value between 1 4 will enable coresponding number of watch points Seeting it to 0 will disable all watch point logic The imp1 and version fields are used to set the fixed fields in the psr register Cache configuration The cache is configured through the cache configuration record type cache_config_type is record icachesize integer size of I cache in Kbytes ilinesize integer words per I cache lin dcachesize integer size of D cache in Kbytes dlinesize integer words per D cache lin bootcache boolean boot from cache Xilinx only end record Valid settings for the cache size are 1 64 Kbyte and must be a power of 2 The line size may be 2 4 words line The instruction and data caches may be configured independently Memory controller configuration The memory controller is configured through the memory controlle
28. ct any cache lines and when control is returned to the interrupted task the cache state is identical to what it was before the interrupt If a cache has been frozen by an interrupt it can only be enabled again by enabling it in the CCR This is typically done at the end of the interrupt handler before control is returned to the interrupted task Gaisler Research 4 4 1 21 LEON user s manual AMBA on chip buses Two on chip buses are provided AMBA AHB and APB The APB bus is used to access on chip registers in the peripheral functions while the AHB bus is used for high speed data transfers The specification for the AMBA bus can be downloaded from ARM at www arm com The full AHB APB standard is implemented and the AHB APB bus controllers can be customised through the TARGET package Additional user defined AHB APB peripherals should be added in the MCORE module AHB bus LEON uses the AMBA 2 0 AHB bus to connect the processor cache controllers to the memory controller and other optional high speed units In the default configuration the processor is the only master on the bus while two slaves are provided the memory controller and the APB bridge Table 5 below shows the default address allocation Address range Size Mapping Module 0x00000000 Ox 1FFFFFFF 512M Prom Memory controller 0x20000000 Ox3FFFFFFF 512M Memory bus I O 0x40000000 Ox 7FFFFFFF 1G Ram 0x80000000 0x9FFFFFFF 256 M On chip regist
29. d and the prom is directly instantiated Depending on the value of pabits either a prom with 1 2 4 or 8 kbyte is instantiated The xilinx sub directory contains two templates virtex_prom256 1 kbyte and virtex_prom2048 8 kbyte The virtex_prom256 contains PMON while virtex_prom2048 contains a prom version of rdbmon from LECCS 1 1 1 The pre defined configuration virtex_2k1k_rdbmon in device vhd will instantiate the virtex_prom2048 prom 9 7 2 PMON S record loader Pmon is a simple monitor that can be placed in an on chip boot prom external prom or cache memories using the boot cache configuration Two versions are provided one to be used for on chip prom or caches bprom c and one for external proms eprom c On reset the monitor scans all ram banks and configures the memory control register 2 accordingly The monitor can detect if 8 16 or 32 bit memory is attached if read modify write sub word write cycles are needed and the size of each ram bank It will also set the stack pointer to the top of ram The monitor writes a boot message on UART1 transmitter Gaisler Research 55 LEON user s manual 9 8 describing the detected memory configuration and then waits for S records to be downloaded on UART receiver It recognises two types of S records memory contents and start address A memory content S record is saved to the specified address in memory while a start address record will cause the monitor to jump to the indicated addre
30. de appropriate library mapping 10 6 2 Synopsys VSS A synopsys_vss setup file is present in the top directory and in the leon and tbench directory to provide appropriate library mapping 10 7 Post synthesis simulation The supplied test benches can be used to simulate the synthesised netlist Use the following procedure e Compile the complete model i e do a make at the top level It is essential that you use the same configuration as during synthesis This step is necessary because the test bench uses the target config and device packages e In the top directory compile the simulation libraries for you ASIC FPGA technology and then your VHDL netlist e Cd to tbench and do make clean all This will rebuild the test bench linking it with your netlist e Cd back to the top directory and simulate you test bench as usual Gaisler Research 60 LEON user s manual 11 Synthesis 11 1 General The model is written with synthesis in mind and has been tested with Synopsys DC Synopsys FPGA Compiler FPGA Express Exemplar Leonardo and Synplicity Synplify synthesis tools Technology specific cells are used to implement the IU FPU register files cache rams and pads These cells can be automatically inferred Synplify and Leonardo only or directly instantiated from the target library Synopsys Non synthesisable code is enclosed in a set of embedded pragmas as shown below pragma translate_off non synthesisable
31. e LEON instruction cache is a direct mapped cache configurable to 1 64 kbyte The instruction cache is divided into cache lines with 8 32 bytes of data Each line has a cache tag associated with it consisting of a tag field and one valid bit for each 4 byte sub block On an instruction cache miss to a cachable location the instruction is fetched and the corresponding tag and data line updated If instruction burst fetch is enabled in the cache control register CCR the cache line is filled from main memory starting at the missed address and until the end of the line At the same time the instructions are forwarded to the IU streaming If the IU cannot accept the streamed instructions due to internal dependencies or multi cycle instruction the IU is halted until the line fill is completed If the IU executes a control transfer instruction branch CALL JMPL RETT TRAP during the line fill the line fill will be terminated on the next fetch If instruction burst fetch is enabled instruction streaming is enabled even when the cache is disabled In this case the fetched instructions are only forwarded to the IU and the cache is not updated If a memory access error occurs during a line fill with the IU halted the corresponding valid bit in the cache tag will not be set If the IU later fetches an instruction from the failed address a cache miss will occur triggering a new access to the failed address If the error remains an instruction acces
32. e also indicates if the slave is capable of returning a SPLIT response if so the split element should be set to true thereby generating the necessary split support logic in the AHB arbiter To add or remove an AHB slave edit the configuration table and the AHB bus decoder multiplexer and will automatically be reconfigured The AHB slaves should be connected to the ahbsi ahbso buses The index field in the table indicates which bus index the slave should connect to 9 8 3 AHB cachability configuration The AHB controller controls which areas contains cachable data This is defined through a table in the AHB configuration record type ahb_cache_config_type is record firstaddr ahb_cache_addr_type lastaddr ahb_cache_addr_type end record type ahb_cache_config_vector is array Natural Range lt gt of ahb_cache_config_type constant ahb_cache_config_void ahb_cache_config_type others gt 0 others gt 0 The standard configuration is to mark the PROM and RAM areas of the memory controller as cachable while the remaining AHB address space is non cachable standard cachability config constant ahbcachecfg_std ahb_cache_config_vector 0 to AHB_CACHE_MAX 1 irst last function HADDR 31 29 000 000 PROM area 0x0 0x0 LEDO ROTI RAM area 0x2 0x3 others gt ahb_cache_config_void 9 8 4 APB configuration The number of APB slaves and their address range is defined th
33. e cat 7 Floating point unit and CO PproceSSOT ceesceceeececesececeeeeecseeeecseeeecseeeeeeteeeees 7 Cars RS a Memory interface nanona O 8 TIMES id 8 Watchdog aio a a a dates aea a ei 8 VAR TS innata 8 inmterrupt contralto 8 PA seo ou saa candace Gade cet covecdac den adades ced a eee to 8 AMBA ORCOS A E ea Schnee 8 B ot loader ie ata coed eat a de eet ook a aa al a ak ts ines paca nao ae ae 8 Watch point Tesisters nc nad diri eden 8 LEON integer Unai iii aah O RERE 9 OC cio 9 o A AE 10 A A AN 10 Multiply and accumulate instructions ooooooococcnuccconancnnnnnnononanonnncnnnnncnnnnncnnnns 11 Divide INSTUCIONS Werder 11 Watch Points y io 11 O 12 EXCEPHONS na a a dd IN 12 PLOCES SOLES CELO a 13 Co sprocessor INTENT ACE iii nidad T Sesnodeetesccoedenaagds 13 FPU terrace dnde tl le ele lle ndo el e is 15 Cache uba ia 16 Instruction cache a cdo dada 16 DP OA c 16 Instruction cache flushing e A a o ina 16 Diagnostic Cache ACCESS siii dd exassdaavasuanaaeedandduvasucsanenasds 16 Instruction Cached ia in 17 Data Cache ui dla 17 A O 17 A O NITO 17 ON 18 Diasnostic cache aras di ios 18 Cache Dy PASS sisi ii saaeansvassd G sustea es degsdazaceasaasuanes cade coat 18 Data cach tag di seuss tessa aden coca EAEE 18 Cache Control Resister E E AD 19 AMBA On chip DISCS a a TAE 21 Gaisler Research 4 LEON user s manual 4 1 4 2 4 3 4 4 5 5 1 5 2 5 2 1 3 2 2 5 2 3 5 3 5 3 1 5 3 2 5 4 5 4 1 5 4 2 5 5 5 5 1 5 5 2
34. e performed For memory operations e g LD and for JMPL RETT the address is generated 4 ME Memory Data cache is accessed For cache reads the data will be valid by the end of this stage at which point it is aligned as appropriate Store data read out in the E stage 1s written to the data cache at this time 5 WR Write The result of any ALU logical shift or cache read operations are written back to the register file Table 1 lists the cycles per instruction assuming cache hit and no load interlock Instruction Cycles JMPL 2 Double load 2 Single store 2 Double store 3 SMUL UMUL 1 2 4 35 SDIV UDIV 35 Taken Trap 4 Atomic load store 3 All other instructions 1 Table 1 Instruction timing depends on multiplier configuration 2 3 Multiply instructions The LEON processor supports the SPARC integer multiply instructions UMUL SMUL UMULCC and SMULCC These instructions perform a 32x32 bit integer multiply producing a 64 bit result SMUL and SMULCC performs signed multiply while UMUL and UMULCC performs unsigned multiply UMULCC and SMULCC also set the condition codes to reflect the result Several multiplier implementation are provided making it possible to choose between area delay and latency see Integer unit configuration on page 51 for more details Gaisler Research 11 LEON user s manual 2 4 2 5 2 6 asr24 asr26 Joasr28 Yasr30 WADDR 31 2 DL DS M
35. e state disabled enabled or frozen indicated in the cache control register 3 2 4 Diagnostic cache access Diagnostic software may read the tags directly by executing a single word load alternate space instructions in ASI space OxE The cache offset indexes the tag to be read all other address bits are ignored Similarly the data sub blocks may be read by executing a single word load alternate space instructions in ASI space OxF The cache offset indexes the line to be read while A 4 2 index which of the sub blocks to be read The tags can be directly written by executing single word store alternate space instructions in ASI space OxE The cache offset indexes the tag to be written and A 31 10 is written into the ATAG filed see below The valid bits are written with the D 7 0 of the write data The data sub blocks can be directly written by executing single word store alternate space instructions in ASI space OxF Address bits The cache offset indexes the cache line and A 4 2 selects the sub block The sub block is written with the write data Note that diagnostic access to the cache is not possible during a FLUSH operation An attempt to perform a diagnostic access during an ongoing flush will cause a data exception trap trap 0x09 3 2 5 Cache bypass The memory can be accessed directly without caching by using ASI 0x0 However if the accessed location is in the data cache the cache will be updated to reflect the changed me
36. ee ns E 59 A A rg al nse aE a a E eii 59 Synopsys VSS iria bass 59 Post synthesis simulation si ad 59 O 60 A a A E A O A A PRT OF POET 60 Synthesis proced re dd 60 A a dew nant ee aa ea rA rE 61 SYMOPSYS DC iii a cs 61 Synopsys FC2 and Synopsys F cscccssscecsssceceeececesececesececsseeecsseceesteeeesaes 61 A E aes Zod Techs ue atas Pied acetate 62 Porting to a new technology or synthesis tOOl ooonccnnncninncnoccconccnocncnoncnonennnos 63 A ice acne clone Bea en eee Ae Goh nda Beet 63 Target specific mesas on taa 63 RegisterTile iia A a is 63 Cachexram memory Clan on 64 Pl a a 64 Adding a new technology or synthesis tOOl ooooonncccinncinocononnnonnnnncnnonncnncnnnos 64 Gaisler Research 6 LEON user s manual 1 1 1 2 1 3 1 4 1 5 Introduction Overview The LEON VHDL model implements a 32 bit processor conforming to the SPARC V8 architecture It is designed for embedded applications with the following features on chip separate instruction and data caches hardware multiplier and divider interrupt controller two 24 bit timers two UARTs power down function watchdog 16 bit I O port and a flexible memory controller Additional modules can easily be added using the on chip AMBA AHB APB buses The VHDL model is fully synthesisable with most synthesis tools and can be implemented on both FPGAs and ASICs Simulation can be done with all VHDL 87 compliant simulators Performance Using a 16x16 multiplie
37. ers APB bridge Table 5 AHB address allocation An attempt to access a non existing device will generate an AHB error response The AHB bus can connect up to 16 masters and any number of slaves The LEON processor core is normally connected as master 0 while the memory controller and APB bridge are connected at slaves O and 1 Each master is connected to the bus through two records corresponding to the AHB signals AHB master inputs HCLK and HRESETn routed separately type AHB_Mst_In_Type is record HGRANT Std_ULogic bus grant HREADY Std_ULogic transfer done HRESP Std_Logic_Vector 1 downto 0 response typ HRDATA std_Logic_Vector HDMAX 1 downto 0 read data bus HCACHE Std_ULogic cacheable access end record AHB master outputs type AHB_Mst_Out_Type is record HBUSREQ Std_ULogic bus request HLOCK Std_ULogic lock request HTRANS Std_Logic_Vector 1 downto 0 transfer type HADDR Std_Logic_Vector HAMAX 1 downto 0 address bus byte HWRITE Std_ULogic read write HSIZE Std_Logic_Vector 2 downto 0 transfer size HBURST Std_Logic_Vector 2 downto 0 burst type HPROT Std_Logic_Vector 3 downto 0 protection control HWDATA Std_Logic_Vector HDMAX 1 downto 0 write data bus end record Each slave is similarly connected through two records Gaisler Research 22 LEON user s manual 4 2
38. esponding function will be suppressed resulting in a smaller design The secondary interrupt controller is enabled by selecting a configuration record with irq2cfg enable true An example record defining four extra interrupts could look like this constant irg2chan4 irq2type enable gt true channels gt 4 filter gt 1v10 lvll edge0 edgel others gt 1v10 Lvl0 mean that the interrupt will be treated as active low Ivll as active high edge0 as negative edge triggered and edgel as positive edge triggered Since the registers in the secondary interrupt controller are accessed through the APB bus an APB configuration with the interrupt controller present must be selected Gaisler Research 54 LEON user s manual 9 7 Boot configuration Apart from that standard boot procedure of booting from address O in the external memory LEON can be configured to boot from an internal prom The boot options are defined on the boot configuration record as defined in the TARGET package type boottype is memory prom dual type boot_config_type is record boot boottype select boot source ramrws integer range 0 to 3 ram read waitstates ramwws integer range 0 to 3 ram write waitstates sysclk integer cpu clock baud positive UART baud rate extbaud boolean us xternal baud rate setting pabits positive internal boot prom address bits end record 9 7 1 Booting from internal prom If the boo
39. full AMBA configuration is defined through two configuration sub records one for the AHB bus and one for APB type ahb_config_type is record masters integer range 1 to AHB_MST_MAX defmst integer range 0 to AHB_MST_MAX 1 split boolean add support for SPLIT reponse slvtable ahb_slv_config_vector 0 to AHB_SLV_MAX 1 cachetable ahb_cache_config_vector 0 to AHB_CACHE_MAX 1 end record type apb_config_type is record table apb_slv_config_vector 0 to APB_SLV_MAX 1 end record 9 8 1 AHB master configuration The number of attached masters is defined by the masters field in the AHB configuration record The masters are connected to the ahbmi ahbmo buses in the MCORE module AHB master should be connected to index 0 masters 1 of the ahbmi ahbmo buses The defmst field indicates which master is granted by default if no other master is requesting the bus Gaisler Research 56 LEON user s manual 9 8 2 AHB slave configuration The number of AHB slaves and their address range is defined through the AHB slave table The default table has only two slaves the memory controller and the APB bridge standard slave config constant ahbslvcfg_std ahb_slv_config_vector 0 to AHB_SLV_MAX 1 first last index split enable function HADDR 31 28 BV OI e false true memory controller 0x0 0x7 1000 1000 1 false true APB bridge 128 MB 0x8 0x8 others gt ahb_slv_config_void The tabl
40. g LEON MCORE UART uart vhd UARTs LEON MCORE LCONF Iconf vhd LEON configuration register LEON MCORE AHBSTAT ahbstat vhd AHB status register Table 12 LEON model hierarchy Table 13 shows the packages used in the LEON model Package File name Function TARGET target vhd Pre defined configurations for various targets DEVICE device vhd Current configuration CONFIG config vhd Generation of various constants for processor and caches SPARCV8 sparcv8 vhd SPARCV8 opcode definitions IFACE iface vhd Type declarations for module interface signals Table 13 LEON packages Gaisler Research 49 LEON user s manual Package File name Function MACRO macro vhd Various utility functions AMBA amba vhd Type definitions for the AMBA buses AMBACOMP ambacomp vhd AMBA component declarations MULTLIB multlib vhd Multiplier modules FPULIB fpu vhd FPU interface package DEBUG debug vhd Debug package with SPARC disassembler TECH_GENERIC tech_generic vhd Generic regfile and pad models TECH_ATC25 tech_atc25 vhd Atmel ATC25 specific regfile ram and pad generators TECH_ATC35 tech_atc35 vhd Atmel ATC35 specific regfile ram and pad generators TECH_MAP tech_map vhd Maps mega cells according to selected target Table 13 LEON packages 8 2 Model coding style 8 3 The LEON VHDL model is designed to be used for both synthesis and board level simulation It is therefore written using
41. ggered and positive edge triggered When the condition is fulfilled the corresponding bit 1s set in the interrupt pending register The pending bits are ANDed with the interrupt mask register and then forwarded to the priority selector If at least one unmasked pending interrupt exists the interrupt output will be driven generating interrupt 10 by default The highest unmasked pending interrupt can be read from the interrupt status register see below Interrupts are not cleared automatically upon a taken interrupt the interrupt handler must reset the pending bit by writing a 1 to the corresponding bit in the interrupt clear register It must then also clear interrupt 10 in the primary interrupt controller Testing of interrupts can be done by writing directly to the interrupt pending registers Bits written with 1 will be set while bits written with 0 will keep their previous value Note that not all 32 interrupts have to be implemented how many are actually used depends on the configuration Unused interrupts are ignored and the corresponding register bits are not generated Mapping of interrupts to the secondary interrupt controller is done by editing mcore vhd See the configuration section on how to enable the controller and how to configure the interrupt filters After reset the interrupt mask register 1s set to all zeros while the remaining control registers are undefined Gaisler Research 29 LEON user s manual 5
42. ier iterative 16x16 32x8 32x16 amp 32x32 e Optional 16x16 bit MAC with 40 bit accumulator e Radix 2 divider non restoring Figure 2 shows a block diagram of the integer unit call branch address I cache x Xa data address y jmpa ior A ALA A ps ure A ee hap Se AA CE 2 rs ny AS RAS a AS e g erin RA he ie Fetch 7 7 5 Ean dpe j Decode imm tbr wim psr T 1 a a E A elinst D pE rst operand2 Execute a ek sik alu shi mul div y pi a Se M_INST e HS sre S MPE 4 pl result yimp 74 Memory 3 EL er DAA W_INSE 2 gt 23 w_pc A iak iae SA at a wres Write 39 lt tbr wim psr regfile rst rs2 Figure 2 LEON integer unit block diagram Gaisler Research 10 LEON user s manual 2 2 Instruction pipeline The LEON integer unit uses a single instruction issue pipeline with 5 stages 1 FE Instruction Fetch If the instruction cache is enabled the instruction is fetched directly from the instruction cache Otherwise the fetch is forwarded to the memory controller The instruction is valid at the end of this stage and is latched inside the IU 2 DE Decode The instruction is decoded and the operands are read Operands may come from the register file or from internal data bypasses CALL and Branch target addresses are generated in this stage 3 EX Execute ALU logical and shift operations ar
43. ift register empty TS indicates that the transmitter shift register is empty Transmitter hold register empty TH indicates that the transmitter hold register is empty Break received BR indicates that a BREAK has been received Overrun OV indicates that one or more character have been lost due to overrun Parity error PE indicates that a parity error was detected Framing error FE indicates that a framing error was detected 12 11 0 RESERVED SCALER RELOAD VALUE Figure 29 UART scaler reload register Gaisler Research 35 LEON user s manual 5 6 Parallel VO port A partially bit wise programmable 32 bit I O port is provided on chip The port is split in two parts the lower 16 bits are accessible via the PIO 15 0 signal while the upper 16 bits uses D 15 0 and can only be used when all areas rom ram and I O of the memory bus is in 8 or 16 bit mode see 8 bit and 16 bit memory configuration on page 41 The low 16 I O ports can be individually programmed as output or input while the high 16 I O ports only be configures as outputs or inputs on byte basis Two registers are associated with the operation of the I O port the combined I O input output register and I O direction register When read the input output register will return the current value of the I O port when written the value will be driven on the port signals if enabled as output The direction register defines the d
44. ill be lost and the overrun bit will be set in the UART status register If flow control is enabled then the RTSN will be negated high when a valid start bit is detected and the receiver holding register contains an un read character When the holding register is read the RTSN will automatically be reasserted again 5 5 3 Baud rate generation Each UART contains a 12 bit down counting scaler to generate the desired baud rate The scaler is clocked by the system clock and generates a UART tick each time it underflows The scaler is reloaded with the value of the UART scaler reload register after each underflow The resulting UART tick frequency should be 8 times the desired baud rate If the EC bit is set the scaler will be clocked by the PIO 3 input rather than the system clock In this case the frequency of PIO 3 must be less than half the frequency of the system clock 5 5 4 Loop back mode If the LB bit in the UART control register is set the UART will be in loop back mode In this mode the transmitter output is internally connected to the receiver input and the RTSN is connected to the CTSN It is then possible to perform loop back tests to verify operation of receiver transmitter and associated software routines In this mode the outputs remain in the inactive state in order to avoid sending out data Gaisler Research 34 LEON user s manual 5 5 5 Interrupt generation The UART will generate an interrupt under the following condi
45. ion register 2 0x800000B4 Secondary interrupt mask register 0x80000008 Reserved 0x800000B8 Secondary interrupt status register 0x8000000C AHB Failing address register 0x800000B8 Secondary interrupt clear register 0x80000010 AHB status register 0x80000014 Cache control register 0x80000018 Power down register 0x8000001C Write protection register 1 0x80000020 Write protection register 2 0x80000024 LEON configuration register 0x80000040 Timer 1 counter register 0x80000044 Timer 1 reload register 0x80000048 Timer 1 control register 0x8000004C Watchdog register 0x80000050 Timer 2 counter register 0x80000054 Timer 2 reload register 0x80000058 Timer 2 control register 0x80000060 Scaler counter register 0x80000064 Scaler reload register 0x80000070 Uart 1 data register 0x80000074 Uart 1 status register 0x80000078 Uart 1 control register 0x8000007C Uart 1 scaler register 0x80000080 Uart 2 data register 0x80000084 Uart 2 status register 0x80000088 Uart 2 control register 0x8000008C Uart 2 scaler register 0x80000090 Interrupt mask and priority register 0x80000094 Interrupt pending register 0x80000098 Interrupt force register 0x8000009C Interrupt clear register Ox800000A0 I O port input output register 0x800000A4 I O port direction register 0x800000A8 I O port interrupt register Table 6 On chip registers
46. ion that a lead out cycle will only occurs after the last transfer 8 bit and 16 bit memory configuration To support applications with low memory and performance requirements efficiently it is not necessary to always have full 32 bit memory banks The RAM and PROM areas can be individually configured for 8 or 16 bit operation by programming the ROM and RAM size fields in the memory configuration registers Since access to memory is always done on 32 bit word basis read access to 8 bit memory will be transformed in a burst of four read cycles while access to 16 bit memory will generate a burst of two 16 bits reads During writes only the necessary bytes will be writen Figure 38 shows an interface example with 8 bit PROM and 8 bit RAM Figure 39 shows an example of a 16 bit memory interface 8 bit PROM WRITEN RAMSN 0 RAMOEN 0 RWEN 0 A 27 0 D 31 24 Figure 38 8 bit memory interface example Gaisler Research 42 LEON user s manual 16 bit PROM s o Eo A OEN JE PROM WRITEN WE D 16 bit RAM RAMSN 0 cs D RAMOEN 0 e RWEN O0 1 RWELTO1 wg SRAM gt A 27 0 D 31 16 Figure 39 16 bit memory interface example 6 7 1 Memory configuration register 1 Memory configuration register is used to program the timing of rom and local I O accesses 31 29 28 27 26 25 24 23 20 19 18 17 12 11 10 9 8 7 4 3 0 Reserved TO waitstates Reserved Prom w
47. irection for each individual port bit O input 1 output 31 18 17 0 IODIR 17 0 Figure 30 I O port direction register e IODIR z VO port direction The value of IODIR 15 0 defines the direction of I O ports 0 15 If bit n is set the corresponding I O port becomes an output otherwise it is an input IODIR 16 controls D 15 8 while IODIR 17 controls D 7 0 The I O ports can also be used as interrupt inputs from external devices A total of four interrupts can be generated corresponding to interrupt levels 4 5 6 and 7 The I O port interrupt configuration register figure 31 defines which port should generate each interrupt and how it should be filtered 31 30 29 28 24 23 22 21 20 16 15 14 13 12 8 765 4 0 ENI LE PL ISEL3 EN LE PL ISEL2 EN LE PL ISEL1 EN LE PL ISELO Figure 31 I O port interrupt configuration register ISELn I O port select The value of this field defines which I O port 0 31 should generate parallel I O port interrupt n e PL Polarity If set the corresponding interrupt will be active high or edge triggered on positive edge Otherwise it will be active low or edge triggered on negative edge LE Level edge triggered If set the interrupt will be edge triggered otherwise level sensitive EN Enable If set the corresponding interrupt will be enabled otherwise it will be masked Gaisler Research 36 LEON user s ma
48. itter serial output then remains inactive until CTSN is asserted again If the CTSN is connected to a receivers RTSN overrun can effectively be prevented 5 5 2 Receiver operation The receiver is enabled for data reception through the receiver enable RE bit in the USART control register The receiver looks for a high to low transition of a start bit on the receiver serial data input pin If a transition is detected the state of the serial input is sampled a half bit clocks later If the serial input is sampled high the start bit is invalid and the search for a valid start bit continues If the serial input is still low a valid start bit is assumed and the receiver continues to sample the serial input at one bit time intervals at the theoretical centre of the bit until the proper number of data bits and the parity bit have been assembled and one stop bit has been detected The serial input is sampled three times for each bit and averaged to filter out noise During this process the least significant bit is received first The data is then transferred to the receiver holding register RHR and the data ready DR bit is set in the USART status register The parity framing and overrun error bits are set at the received byte boundary at the same time as the receiver ready bit is set If both receiver holding and shift registers contain an un read character when a new start bit is detected then the character held in the receiver shift register w
49. lave and acts as the only master on the APB bus The slaves are connected through a pair of records containing the APB signals APB slave inputs PCLK and PRESETn routed separately type APB_Slv_In_Type is record PSEL Std_ULogic PENABLE Std_ULogic PADDR Std_Logic_Vector PAMAX 1 downto 0 PWRITE Std_ULogic PWDATA Std_Logic_Vector PDMAX 1 downto 0 end record APB slave outputs type APB_Slv_Out_Type is record PRDATA Std_Logic_Vector PDMAX 1 downto 0 end record The number of APB slaves and their address range is defined through the APB slave table in the TARGET package The default table has 10 slaves AHB status register Any access triggering an error response on the AHB bus will be registered in two registers AHB failing address register and AHB status register The failing address register will store the address of the access while the memory status register will store the access and error types The registers are updated when an error occur and the NE new error is set When the Gaisler Research 4 4 NE bit is set interrupt 1 is generated to inform the processor about the error After an error the NE bit has to be reset by software Figure 8 shows the layout of the AHB status register 31 23 8 7 6 LEON user s manual 3 2 RESERVED NE RW HMASTER HSIZE Figure 8 AHB status register e 8 NE New error Se
50. lowing two records type cp_unit_in type is record coprocessor execution unit input opl std_logic_vector 63 downto 0 operand 1 op2 std_logic_vector 63 downto 0 operand 2 opcode std_logic_vector 9 downto 0 opcode start std_logic start load std_logic load operands flush std_logic cancel operation end record type cp_unit_out_type is record coprocessor execution unit output res std_logic_vector 63 downto 0 result cc std_logic_vector 1 downto 0 condition codes exc std_logic_vector 5 downto 0 exception busy std Logic eu busy end record The waveform diagram for the execution unit interface can be seen in figure 4 CLK i cpi op1 Kop D X cpi op2 aot X cpi opcode OPC xO cpi start E cpi load EE cpo busy Vo Cpo cc a S O O condition codes cpo exc IES A y ption codes cpo result ARA rest Figure 4 Execution unit waveform diagram The execution unit is started by asserting the start signal together with a valid opcode The operands are driven on the following cycle together with the load signal If the instruction will take more than one cycle to complete the execution unit must drive busy from the cycle after the start signal was asserted until the cycle before the result is valid The result condition codes and exception information are valid from the cycle after the de assertion of busy and until the next assertion of start The opcode c
51. mbler A SPARC disassembler is provided in the DEBUG package It is used by the test bench to disassemble the executed instructions and print them to stdout 1f enabled Test bench configurations with names ending in a _d have disassembly enabled 10 5 Test suite The supplied test suite which is run by the test bench and only tests on chip peripherals and interfaces compliance to the SPARC standard has been tested with proprietary test vectors not supplied with the model To re compile the test program the LEON ERC32 GNU Cross Compiler System LECCS provided by Gaisler Research www gaisler com needs to be installed The test programs are in the tsource directory and are built by executing make tests in the top directory or in the tsource directory The makefile will build the program and generate prom and ram images for the test bench Pre compiled images are supplied so that the test suite can be run without installing the compiler The test programs probes the LEON configuration register to determine which options are enabled in the particular LEON configuration and only tests those E g if no FPU is present the test program will not attempt to perform FPU testing 10 6 Simulator specific support 10 6 1 Modelsim The file modelsim wave do is a macro file for modelsim to display some useful internal LEON signals A modelsim init file modelsim ini is present in the top directory and in the leon and tbench directory to provi
52. mory contents 3 2 6 Data cache tag A data cache tag entry consists of several fields as shown in figure 6 31 109 8 7 0 ATAG 00 VALID Figure 6 Data cache tag layout Field Definitions Gaisler Research 19 LEON user s manual 3 3 e 30 12 Address Tag ATAG Contains the address of the data held in the cache line e 3 0 Valid V When set the corresponding sub block of the cache line contains valid data These bits is set when a sub block is filled due to a successful cache miss a cache fill which results in a memory error will leave the valid bit unset V O corresponds to address 0 in the cache line V 1 to address 1 V 2 to address 2 and V 3 to address 3 NOTE only the necessary bits will be implemented in the cache tag depending on the cache configuration As an example a 2 kbyte cache with 32 bytes per line would only have eight valid bits and 21 tag bits The cache rams are sized automatically by the ram generators in the model Cache Control Register The operation of the instruction and data caches is controlled through a common Cache Control Register CCR figure 7 Each cache can be in one of three modes disabled enabled and frozen If disabled no cache operation is performed and load and store requests are passed directly to the memory controller If enabled the cache operates as described above In the frozen state the cache is accessed and kept in sync with the main memory as if
53. nd anded with the mask field A write protection error is generated if the result is not equal to zero the corresponding unit is enabled and the block protect bit BP is set or if the BP bit is cleared and the result is equal to zero If a write protection error is detected the write cycle is aborted and a memory access error is generated Gaisler Research 44 LEON user s manual 31 30 29 15 14 0 EN BP TAG 14 0 MASK 14 0 Figure 42 Write protection register 1 amp 2 e 14 0 Address mask MASK this field contains the address mask e 29 15 Address tag TAG this field is compared against address 29 15 e 30 Block protect BP if set selects block protect mode e 31 Enable EN if set enables the write protect unit The ROM area can be write protected by clearing the write enable bit MCR1 Gaisler Research 45 LEON user s manual 7 Signals All input signals are latched on the rising edge of CLK All outputs are clocked on the rising edge of CLK 7 1 Memory bus signals Name Type Function Active A 30 0 Output Memory address High BEXCN Input Bus exception Low BRDYN Bus ready strobe Low D 31 0 Memory data High IOSN Local I O select Low OEN Output enable Low RAMOEN 3 0 RAM output enable Low RAMSNI 3 0 RAM chip select Low READ Read strobe High ROMSN 1 0 PROM chip select Low RWEN 3 0 RAM write enable Low WRITEN Output Write strobe Low
54. nfig_type apb apb_config_type mctrl mctrl_config_type boot boot_config_type debug debug_config_type pci pci_config_type peri peri_config_type end record Synthesis configuration The synthesis configuration sub record is used to adapt the model to various synthesis tools and target libraries type targettechs is gen virtex atc35 atc25 synthesis configuration type syn_config_type is record targettech targettechs infer_ram boolean infer cache ram automatically infer_regf boolean infer regfile automatically infer_rom boolean infer boot prom automatically infer_pads boolean infer pads automatically infer_mult boolean infer multiplier automatically gatedclk boolean select clocking strategy rfsyncrd boolean synchronous register file read port end record Depending on synthesis tool and target technology the technology dependant mega cells ram rom pads can either be automatically inferred or directly instantiated Using direct instantiation three types of target technologies are currently supported Xilinx Virtex FPGA Atmel ATC35 0 35 um CMOS and Atmel ATC25 0 25 um CMOS In addition any technology that is supported by synthesis tools capable of automatic inference of mega cells Synplify and Leonardo is also supported When using tools with inference capability targeting Xilinx Virtex a choice can be made to either infer the mega cells automatically
55. nterrupt level PIL becomes pending All other functions and peripherals operate as nominal during the power down mode Gaisler Research 38 LEON user s manual 6 External memory access 6 1 Memory interface The memory bus provides a direct interface to PROM static RAM and memory mapped I O devices Chip select decoding is done for two PROM banks one I O bank and four RAM banks Figure 33 shows how the connection to the different device types is made ROMSN 1 0 Figure 33 Memory device interface 6 2 Memory controller The external memory bus is controlled by a programmable memory controller The controller acts as a slave on the AHB bus The function of the memory controller is programmed through memory configuration registers 1 amp 2 MCR1 amp MCR2 through the APB bus The memory bus supports three types of devices prom ram and local I O The memory bus can also be configured in 8 bit mode for applications with low memory and performance demands The controller can decode a 2 Gbyte address space divided according to table table 9 Address range Size Mapping 0x00000000 Ox 1 FFFFFFF 512M Prom 0x20000000 Ox3FFFFFFF 512M TO 0x40000000 Ox7FFFFFFF 1G RAM Table 9 ASI map Gaisler Research 39 LEON user s manual 6 3 RAM access The RAM area can be up to 1 Gbyte divided on four RAM banks The size of each bank is programmed in the RAM bank size field MCR2 12 9 and can be set in
56. nthesis configurations Note e 8 16 bit memory support is optional make sure that you enable the option s if needed e Make sure that the selected configuration in the DEVICE package correctly reflects your synthesis tools and target technology Gaisler Research 61 LEON user s manual 11 2 1 Synplify To synthesise LEON using Synplify start synplify in the syn directory and open leon prj A synthesis run takes about 15 minutes on a 650 MHz Pentium II PC 128 MB ram necessary The table below shows some obtained synthesis results post layout timing Icache Dcache Regfile Device Freq Area Kbyte Kbyte implement MHz 2 2 EAB EPF10K200E 1 20 5 800 LC 8 4 blockRam XCV300E 8 45 5 000 LUT 8 8 RAM16X1 XCV400E 8 48 6 300 LUT Table 16 Synplify project files If you use synplify 6 11 or earlier versions the FSM complier must be switched off or the UART receiver will not be correctly synthesised due to synplify bugs 11 2 2 Synopsys DC To synthesise LEON using Synopsys DC start synopsys in the syn directory and execute the script leon dcsh Before executing the script edit the beginning of the script to insure that the library search paths reflects your synopsys installation and that the timing constraints are appropriate KK KK KK RR A A A A A A A A A A A I I Script to compile leon with synopsys DC Jiri Gaisler Gaisler Research 2001 E AA Li
57. nual 5 7 To save pins I O pins are shared with other functions according to the table below T O port Function Type Description Enabling condition PIO 15 TXD1 Output UARTI transmitter data UART transmitter enabled PIO 14 RXD1 Input UART receiver data PIO 13 RTS1 Output UARTI request to send UART flow control enabled PIO 12 CTS1 Input UART clear to send PIO 11 TXD2 Output UART2 transmitter data UART transmitter enabled PIO 10 RXD2 Input UART receiver data PIO 9 RTS2 Output UART2 request to send UART2 flow control enabled PIO 8 CTS2 Input UART 2 clear to send PIO 4 Boot select Input Internal or external boot prom PIO 3 UART clock Input Use as alternative UART clock PIO 1 0 Prom width Input Defines prom width at boot time Table 8 UART IO port usage LEON configuration register Since LEON is synthesised from a extensively configurable VHDL model the LEON configuration register read only is used to indicate which options were enabled during synthesis For each option present the corresponding register bit is hardwired to 1 Figure 32 shows the layout of the register 31 30 29 28 27 26 25 24 20 19 17 16 15 14 12 11 10 9 8 765 4 3 2 10 NWINDOWS ICSZ ILSZ DCSZ DLSZ L_UMAC SMAC inst UDIV SDIV inst SMUL UMUL inst Watchdog present Memory status reg FPU PCI core Write protection
58. odeltech compiler Doing a make vss will build the model with Synopsys VSS To use an other simulator the makefiles in the leon and tbench sub directories have to be modified to reflect the simulator commands On non unix systems e g windows the compile bat file in the leon and tbench directories can be used to compile the model in correct order 10 3 Generic test bench A generic test bench is provided in tbench tbgen vhd This test bench allows to generate a model of a LEON system with various memory sizes and configuration by setting the appropriate generics A default configuration of the test bench TBDEF is in tbench tbdef vhd The file tbench tbleon vhd contains a number of alternative configuration using the generic test bench Once the LEON model have been compiled one of the test benches e g TBDEF can be simulated to verify the behaviour of the model Simulation should be started in the top directory The output from the simulation should be as follows xxx Starting LEON system test Memory interface test Cache memory Register fil Interrupt controller Timers watchdog and power down Parallel 1 0 port UARTS Test completed OK halting with failure Failure TEST COMPLETED OK ending with FAILURE Se H SE OSE de SHE Ae e e Se de e de Se e de e e e Simulation is halted by generating a failure Gaisler Research 59 LEON user s manual 10 4 Disasse
59. omatically inferred by the synthesis tool targeting FPGA technologies For ASIC technologies generate statements are used to instantiate technology dependant pads The selection of pads is done in TECH_MAP 12 2 4 Adding a new technology or synthesis tool Adding support for a new target library or synthesis tool is done as follows 1 Create a package similar to tech_ vhd containing the specific rams regfile and pads 2 Edit target vhd to include your technology or synthesis tool in targettechs 3 Edit tech_map vhd to instantiate the cells when the technology is selected 4 Define and select a configuration using the new technology target vhd device vhd 5 Submit your changes to jiri gaisler com for inclusion in future version of LEON
60. pi opcode 9 0 is the concatenation of bits 19 13 5 of the instruction If execution of a co processor instruction need to be pre maturely aborted due to an IU trap cpi flush will be asserted for two clock cycles The execution unit should then be reset to its idle condition Gaisler Research 15 LEON user s manual 2 11 FPU interface The LEON model can be connected to the Meiko floating point core thereby providing full floating point support according to the SPARCV8 standard Two interface options are available either a parallel interface identical to the above described co processor interface or an integrated interface where FP instruction do not execute in parallel with IU instruction The FPU interface is enabled selected by setting of the FPU element of the configuration record The direct FPU interface does not implement a floating point queue the processor is stopped during the execution of floating point instructions This means that QNE bit in the fsr register always is zero and any attempts of executing the STDFQ instruction will generate a FPU exception trap The parallel interface lets FPU instructions execute in parallel with IU instructions and only halts the processor in case of data or resource dependencies Refer to the SPARC V8 manual for a more in depth discussion of the FPU and co processor characteristics Gaisler Research 16 LEON user s manual 3 1 Cache sub system Instruction cache 3 1 1 Operation Th
61. pt_level_10 Ox1A 22 Asynchronous interrupt 10 interrupt_level_11 0x1B 21 Asynchronous interrupt 11 interrupt_level_12 0x1C 20 Asynchronous interrupt 12 interrupt_level_13 0x1D 19 Asynchronous interrupt 13 interrupt_level_14 Ox1E 18 Asynchronous interrupt 14 interrupt_level_15 Ox1F 17 Asynchronous interrupt 15 trap_instruction Ha 16 Software trap instruction TA x Table 3 Trap allocation and priority 2 9 Processor reset operation The processor is reset by asserting the RESET input for at least one clock cycle The following table indicates the reset values of the registers which are affected by the reset All other registers maintain their value or are undefined Register Reset value PC program counter 0x0 nPC next program counter 0x4 PSR processor status register ET 0 S 1 CCR cache control register 0x0 Table 4 Processor reset values Execution will start from address 0 2 10 Co processor interface LEON can be configured to provide a generic interface to a special purpose co processor The interface allows an execution unit to operate in parallel to increase performance One co processor instruction can be started each cycle as long as there are no data dependencies Gaisler Research 14 LEON user s manual When finished the result is written back to the co processor register file The execution unit 1s connected to the interface using the fol
62. r the drystone 2 1 benchmark reports 2 000 iteration s MHz This translates to 55 drystone MIPS at 50 MHz or 110 MIPS at 100 MHz News in LEON 1 version 2 3 5 leon 2 3 5 is primarily a bug fix release not new features has been added The following modifications has been done e Corrected missing I O pad problem in the ATC25 port e Cleaned up generation of regfile write strobe e Fixed bprom c to correctly detect 8 bit ram License The LEON VHDL model is provided under two licenses the GNU Public License GPL and the Lesser GNU Public License LGPL The LGPL applies to the LEON model itself while remaining support files and test benches are provided under GPL This means that you can use LEON as acore in a system on chip design without having to publish the source code of any additional IP cores you might use You must however publish any modifications you have made to the LEON core itself as described in LGPL Fault tolerant LEON LEON FT The original LEON design includes advanced fault tolerance features to withstand arbitrary single event upset SEU errors without loss of data The fault tolerance is provided at design VHDL level and does not require an SEU hard semiconductor process nor a custom cell library or special back end tools The LGPL version of LEON is a sub set derived from the fault tolerant model This document provides some references to LEON FT functionality which users of the LGPL version safely can disregard
63. r configuration record type mctrl_config_type is record bus8en boolean nable 8 bit bus operation busl6en boolean nable 16 bit bus operation rawaddr boolean enable unlatched address option end record The 8 and 16 bit memory interface features are optional if set to false the associated function will be disabled resulting in a smaller design The rawaddr fields enables the raw unlatched address output option in the memory controller If enabled timing analysis of the address bus might be difficult since the bus outputs can be driven both by registers synchronous and combinational logic asynchronous Debug configuration Various debug features are controlled through the debug configuration record type debug_config_type is record enable boolean nable debug port uart boolean enable fast uart data to console iureg boolean enable tracing of iu register writes fpureg boolean enable tracing of fpu register writes nohalt boolean dont halt on error pclow integer set to 2 for synthesis 0 for debug end record Gaisler Research 53 LEON user s manual 9 6 The enable field has to be true to enable the built in disassembler it does not affect synthesis Setting uart to true will tie the UART transmitter ready bit permanently high for simulation does not affect synthesis and output any sent characters on the simulator console line buffered The UART output TX will not simula
64. rather high level VHDL constructs mostly using sequential statements Typically each module only contains two processes one combinational process describing all functionality and one process implementing registers Records are used extensively to group signals according their functionality In particular signals between modules are passed in records Clocking scheme The model implements two clocking schemes a continuous clock and the use of multiplexers to enable loading of pipe line registers or a gated clock which is stopped during pipe line stalls While a continuous clock provides easier timing analysis gated clocks usually cost less area and power The selection of clock scheme is done by setting the configuration element GATEDCLK to true or false Gaisler Research 50 LEON user s manual 9 9 1 Model Configuration The model is configurable to allow different cache sizes multiplier performance clock generation and target technologies Several configurations are defined as constant records in the TARGET package while the active configuration record is selected in the DEVICE package The model is configured from a master configuration record which contains a number of sub records which each configure a specific module function complete configuration record type type config_type is record synthesis syn_config_type iu iu_config_type fpu fpu_config_type cp cp_config_type cache cache_config_type ahb ahb_co
65. rd nwindows set the number of register windows the SPARC standard allows 2 32 windows but to be compatible with the window overflow underflow handlers in the LECCS compiler 8 windows should be used The multiplier option selects how the multiply instructions are implemented The table below show the possible configurations Configurati latency approx area on clocks Kgates iterative 35 1000 ml6x16 4 6 000 m32x8 4 5 000 m32x16 2 9 000 mx32x32 1 15 000 Table 14 Multiplier configurations If infer_mult in the synthesis configuration record see above is false the multipliers are implemented using the module generators in multlib vhd Ifinfer_mult is true the synthesis tool will infer a multiplier For FPGA implementations best performance is achieved when infer_mult is true and m16x16 is selected ASIC implementations using synopsys DC should set infer_mult to false since the provided multiplier macros in MULTLIB are faster than the synopsys generated equivalents The mac option enables the SMAC UMAC instructions Requires the multiplier to use the m16x16 configuration The divider field select how the UDIV SDIV instructions are implemented Currently only a radix 2 divider is available If an FPU will be attached fpuen should be set to 1 If a co processor will be attached cpen should be set to true Gaisler Research 52 LEON user s manual 9 3 9 4 9 5 To speed up bran
66. rite ws Prom read ws T O wid T O enable VO ready enable External alatch BEXCN enable Prom write enable Prom width Figure 40 Memory configuration register 1 e 3 0 Prom read waitstates Defines the number of waitstates during prom read cycles 0000 0 0001 1 1111 15 e 7 4 Prom write waitstates Defines the number of waitstates during prom write cycles 0000 0 0001 1 1111 15 e 9 8 Prom with Defines the data with of the prom area 00 8 01 16 10 32 e 10 Reserved e 11 Prom write enable If set enables write cycles to the prom area e 17 12 Reserved e 18 External address latch enable If set the address is sent out unlatched and must be latched by external address latches e 19 VO enable If set the access to the memory bus I O area are enabled Gaisler Research 43 LEON user s manual 6 8 e 23 20 I O waitstates Defines the number of waitstates during I O accesses 0000 0 0001 1 0010 2 1111 15 e 25 Bus error BEXCN enable e 26 Bus ready BRDYN enable e 28 27 I O bus width Defines the data with of the I O area 00 8 01 16 10 32 During power up the prom width bits 9 8 are set with value on PIO 1 0 inputs The prom waitstates fields are set to 15 maximum External bus error and bus ready are disabled All other fields are undefined 6 7 2 Memor
67. rough the APB slave table in the TARGET package The default table has 10 slaves constant APB _SLV_MAX integer 16 maximum APB slaves constant APB_SLV_ADDR_BITS integer LOY address bits to decode APB slaves subtype apb_range_addr_type is std_logic_vector APB_SLV_ADDR_BITS 1 downto 0 type apb_slv_config_type is record firstaddr apb_range_addr_type lastaddr apb_range_addr_type index integer enable boolean end record type apb_slv_config_vector is array Natural Range lt gt of apb_slv_config_type constant apb_slv_config_void apb_slv_config_type others gt 0 others gt 0 0 false Gaisler Research 57 LEON user s manual standard config constant apbslvcfg_std apb_slv_config_vector 0 to APB_SLV_MAX 1 first last index enable function PADDR 9 0 0000000000 0000001000 O true memory controller 0x00 0x08 0000001100 0000010000 1 true AHB status reg 0x0C 0x10 0000010100 0000011000 2 true cache controller 0x14 0x18 0000011100 0000100000 3 true write protection 0x1C 0x20 0000100100 0000100100 4 true config register 0x24 0x24 0001000000 0001101100 5 true timers 0x40 0x6C 0001110000 0001111100 6 true uartl 0x70 Ox7C 0010000000 0010001100 7 true uart2 0x80 0x8C 0010010000 0010011100 8
68. s error trap tt 0x1 will be generated 3 1 2 Instruction cache flushing The instruction cache is flushed by executing the FLUSH instruction or by writing to ASI 0x5 The flushing will take one cycle per cache line during which the IU will not be halted but during which the instruction cache will be disabled When the flush operation is completed the cache will resume the state disabled enabled or frozen indicated in the cache control register 3 1 3 Diagnostic cache access Diagnostic software may read the tags directly by executing a single word load alternate space instructions in ASI space OxC Address bits making up the cache offset will be used to index the tag to be read all other address bits are ignored Similarly the data sub blocks may be read by executing a single word load alternate space instructions in ASI space OxD The cache offset indexes the line to be read while A 4 2 indexes which of the eight sub blocks to be read The tags can be directly written by executing single word store alternate space instructions in ASI space OxC The cache offset will index the tag to be written and D 31 12 is written into the ATAG filed see below The valid bits are written with the D 7 0 of the write data The data sub blocks can be directly written by executing single word store alternate space instructions in ASI space OxD The cache offset indexes the cache line and A 4 2 selects the Gaisler Research 17 LEON user s manual
69. select signal for the PROM area ROMSN O is asserted when the lower half of the PROM area is accessed 0 0x10000000 while ROMSNT 1 is asserted for the upper half RAMOENT 3 0 RAM output enable output These active low signals provide an individual output enable for each RAM bank RAMSN 3 0 RAM chip select output These active low outputs provide the chip select signals for each RAM bank Gaisler Research 47 LEON user s manual READ Read cycle This active high output is asserted during read cycles on the memory bus RWEN 3 0 RAM write enable output These active low outputs provide individual write strobes for each byte lane RWEN O controls D 31 24 RWEN 1 controls D 23 16 etc WRITEN Write enable output This active low output provides a write strobe during write cycles on the memory bus CLK Processor clock input This active high input provides the main processor clock ERROR Processor error open drain output This active low output is asserted when the processor has entered error state and is halted This happens when traps are disabled and an synchronous un maskable trap occurs PIO 15 0 Parallel I O port bi directional These bi directional signals can be used as inputs or outputs to control external devices RESETN Processor reset input When asserted this active low input will reset the processor and all on chip peripherals WDOGN Watchdog time out open drain
70. sr28 30 and asr30 31 registers one with the break address and one with a mask 31 2 1 0 31 2 0 asr25 asr27 asr29 asr3 1 WMASK 31 2 Figure 3 Watch point registers Gaisler Research 12 LEON user s manual Any binary aligned address range can be watched the range is defined by the WADDR field masked by the WMASK field WMASK x 1 enables comparison On a watch point hit trap OxOB is generated By setting the IF DL and DS bits a hit can be generated on instruction fetch data load or data store Clearing these three bits will effectively disable the watch point function 2 7 ASI assignment The table shows the address space identifier ASI usage for LEON Only ASI 3 0 are used for the mapping ASI 7 4 have no influence on operation ASI Usage 0x0 0x1 0x2 0x3 0x4 0x7 Uncached access Will update the cache on read hit 0x5 Flush instruction cache 0x6 Flush data cache 0x8 0x9 OxA OxB Cached access OxC Instruction cache tags OxD Instruction cache data OxE Data cache tags OxF Data cache data Table 2 ASI usage 2 8 Exceptions LEON adheres to the general SPARC trap model The table below shows the implemented traps and their individual priority Trap TT Pri Description reset 0x00 1 Power on reset write error 0x2b 2 write buffer error instruction_access_error 0x01 3 Error during instruction fet
71. ss Applications compiled with LECCS can be converted to a suitable S record stream with sparc rtems objcopy O srec app app srec See the README files in the pmon directory for more details After successful boot the monitor will write a message similar to LEON 1 2 2048K 32 bit memory gt 9 7 3 Rdbmon A promable version of rdbmon is provided in pmon lmon o It can be put in the boot prom if infer_prom is false and pabits 11 Note that rdbmon needs to be re compiled for each specific target hardware it does not automatically detect the memory configuration To do this change the makefile in the pmon directory so that the mkprom settings will reflect your hardware Then do a make which will produce a virtex_prom2048 mif file Use the Xilinx Coregen to produce a synchronous ram from the mif file and put the resulting edif file virtex_prom2048 edn in the syn directory so that the Xilinx place amp route tools will find it during design expansion The file virtex_prom2048 xco contains a suitable project file for coregen LECCS 1 1 1 or higher is needed to build rdbmon for the boot prom Rdbmon consumes 8 kbyte 16 Virtex blockrams so at least an XCV800 device is needed to fit both the boot prom and ram for the caches and register file AMBA configuration The AMBA buses are the main way of adding new functional units The LEON model provides a flexible configuration method to add and map new AHB APB compliant modules The
72. st paths to your sources target and link libraries below include atc35setup dcsh constraints tailor to your own technology frequency 62 5 clock_skew 0 25 input_setup 2 0 output_delay 5 0 don t touch anything from here unless you know what you are doing The top level constraints are used to generate the appropriate synopsys constraints commands 11 2 3 Synopsys FC2 and Synopsys FE To synthesise LEON using Synopsys FC2 FE start fc2_shell fe2_shell in the syn directory and execute the script leon fc2 The script will analyse all source files and create a leon project Compilation and optimisation is left to the user Note FC2 FE do NOT support automatic inference of ram cells rams have to be directly instantiated from the target library Currently only the Xilinx VIRTEX technology is supported through the TECH_VIRTEX package Gaisler Research 62 LEON user s manual 11 2 4 Leonardo Use the following steps to synthesise LEON using Exemplar Leonardo e Start Leonardo and select target technology and device e Read the technology library e Set working directory to leon syn e Run the leon tcl script which will analyse and elaborate the design Compilation and optimisation is left to the user It is essential that the source files are read with the dont_elaborate switch or Leonardo will not be able to properly resolve certain generate statements Note only Leonardo version 2001 1a or
73. states datal data2 lead out CLK ROMSN OEN Figure 36 Prom read cycle Two PROM chip select signals are provided ROMSN 1 0 ROMSN 0 is asserted when the lower half 0 0x 10000000 of the PROM area as addressed while ROMSN 1 is asserted for the upper half 0x10000000 0x20000000 When the VHDL model is configured to boot from internal prom see Boot configuration on page 54 ROMSN 0 is never asserted and all accesses between 0 0x10000000 are mapped on the internal prom When the model is configured to support both external and internal boot prom the PIO 4 input is used to enable the internal prom 6 5 Memory mapped I O Accesses to I O have similar timing to ROM RAM accesses the differences being that a additional waitstates can be inserted by de asserting the BRDYN signal A lead in cycle is always added to provide stable address before IOSN is asserted lead in datal data2 lead out A IOSN OEN BRDYN Figure 37 I O read cycle Gaisler Research 41 LEON user s manual 6 6 6 7 Burst cycles To improve the bandwidth of the memory bus accesses to consecutive addresses can be performed in burst mode Burst transfers will be generated when the memory controller is accessed using an AHB burst request These includes instruction cache line fills double loads and double stores The timing of a burst cycle is identical to the programmed basic cycle with the except
74. t option is set to prom an internal prom will be inferred When booting from internal prom the UART baud generator timer 1 scaler and memory configuration register 2 are preset to the values calculated from the boot configuration record The UART scaler is preset to generate the desired baud rate taking the system clock frequency into account The timer 1 scaler is preset to generate a 1 MHz tick to the timers The ram read and write waitstate are set directly from to the boot configuration record If the extbaud variable is set in the boot configuration record the UART scalers will instead be initialised with the value on I O port 7 0 the top 4 bits of the scalers will be cleared Using external straps or assigning the port as pull up pull down the desired baud rate can be set regardless of clock frequency and without having to regenerate the prom or re synthesise If a different boot program is desired use the utility in the pmon directory to generate a new prom file When the dual boottype is configured the boot source is defined by PIO 4 If PIO 4 is asserted 1 the internal prom will be enabled otherwise the external prom will be used Which content is placed in the boot prom is decided by the infer_prom and the pabits settings in the configuration record If infer_prom is true the contents is generated from bprom vhd which by default contains PMON see below If infer_prom is false only Xilinx Virtex devices can be targette
75. t when a new error occurred e 7 RW Read Write This bit is set if the failed access was a read cycle otherwise it is cleared e 6 3 HMASTER AHB master This field contains the HMASTER 3 0 of the failed access e 2 0 HSIZE transfer size This filed contains the HSIZE 2 0 of the failed transfer AHB cache aspects Since no MMU is provided with LEON the AHB controller generates a signal which indicates to the AHB masters whether the current access may be cached The areas containing cachable data are defined through a table in the AHB configuration record The standard configuration is to mark the PROM and RAM areas of the memory controller as cachable while the remaining AHB address space is non cachable There is no cache snooping performed by the cache controllers if data is sent to memory from an other AHB master than the processor a data cache flush operation should be done before the new data can safely be used by the processor Alternatively the data can be accessed through ASI 0 to bypass the cache Gaisler Research 24 LEON user s manual 5 On chip peripherals 5 1 On chip registers A number of system support functions are provided directly on chip The functions are controlled through registers mapped APB bus according to the following table Address Register Address 0x80000000 Memory configuration register 1 0x800000B0 Secondary interrupt pending register 0x80000004 Memory configurat
76. te properly in this mode Setting iureg will trace all IU register writes to the console Setting fpureg will trace all FPU register writes to the console Setting nohalt will cause the processor to take a reset trap and continue execution when error mode trap in a trap is encountered Do NOT set this bit for synthesis since it will violate the SPARC standard and will make it impossible to halt the processor Since SPARC instructions are always word aligned all internal program counter registers only have 30 bits A 31 2 making them difficult to trace in waveforms If pclow is set to 0 the program counters will be made 32 bit to aid debugging Only use pclow 2 for synthesis Peripheral configuration Enabling of some peripheral function is controlled through the peripheral configuration record type irg_filter_type is 1v10 lvll edge0 edgel type irg_filter_vec is array 0 to 31 of irq filter _ type type irg2type is record enable boolean secondary interrupt controller channels integer number of additional interrupts 1 32 filter irq_filter_vec irq filter definitions end record type peri_config_type is record c greg boolean enable LEON configuration register ahbstat boolean enable AHB status register wprot boolean enable RAM write protection unit wdog boolean enable watchdog irgq2cfg irq2type secondary interrupt controller config end record If not enabled the corr
77. te sub block On a data cache read miss to a cachable location 4 bytes of data are loaded into the cache from main memory 3 2 2 Write buffer The write buffer WRB consists of three 32 bit registers used to temporarily hold store data until it is sent to the destination device For half word or byte stores the stored data replicated into proper byte alignment for writing to a word addressed device before being loaded into one of the WRB registers The WRB is emptied prior to a load miss cache fill sequence to avoid any stale data from being read in to the data cache Since the processor executes in parallel with the write buffer a write error will not cause an exception to the store instruction Depending on memory and cache activity the write cycle may not occur until several clock cycles after the store instructions has completed If a write error occurs the currently executing instruction will take trap 0x2b Gaisler Research 18 LEON user s manual Note the 0x2b trap handler should flush the data cache since a write hit would update the cache while the memory would keep the old value due the write error 3 2 3 Data cache flushing The data cache can be flushed by executing the flush instruction or by writing to ASI 0x6 any address or data The flushing will take one cycle per line during which the IU will not be halted but during which the data cache will be disabled When the flush operation is completed the cache will resume th
78. the AMBA AHB APB interface making it easy to add more of them or reuse them on other processors using AMBA 1 6 11 Boot loader A on chip boot loader can optionally be enabled allowing to boot the processor and download applications without any external boot prom This feature is mostly suitable for FPGA implementations In larger FPGAs a monitor compatible with the GNU debugger gdb can also be included 1 6 12 Watchpoint registers To aid software debugging up to four watchpoint registers can be configured Each register can cause a trap on an arbitrary instruction or data address range Gaisler Research LEON user s manual 32 ex pc 30 jmpl address D cache address dataout datain 2 LEON integer unit The LEON integer unit IU implements SPARC integer instructions as defined in SPARC Architecture Manual version 8 It is a new implementation not based on any previous designs The implementation is focused on portability and low complexity 2 1 Overview The LEON integer unit has the following features e 5 stage instruction pipeline e Separate instruction and data cache interface e Support for 2 32 register windows e Configurable multipl
79. tions when the transmitter is enabled the transmitter interrupt is enabled and the transmitter holding register moves from full to empty when the receiver is enabled the receiver interrupt is enabled and the receiver holding register moves from empty to full when the receiver is enabled the receiver interrupt is enabled and a character with either parity framing or overrun error is received 5 5 6 UART registers 31 31 8 765 4 3 2 1 0 RESERVED EC LB FL PE PS TI RI TE RE AANA kh YN FY O Figure 27 UART control register Receiver enable RE if set enables the receiver Transmitter enable TE if set enables the transmitter Receiver interrupt enable RI if set enables generation of receiver interrupt Transmitter interrupt enable TI if set enables generation of transmitter interrupt Parity select PS selects parity polarity 0 odd parity 1 even parity Parity enable PE if set enables parity generation and checking Flow control FL if set enables flow control using CTS RTS Loop back LB if set loop back mode will be enabled External Clock if set the UART scaler will be clocked by PIO 3 31 76543210 RESERVED FE PE OV BR TH TS DRI Aan h UNEO Figure 28 UART status register Data ready DR indicates that new data is available in the receiver holding register Transmitter sh
80. ultiply and accumulate instructions To accelerate DSP algorithms two multiply amp accumulate instructions are implemented UMAC and SMAC The UMAC performs an unsigned 16 bit multiply producing a 32 bit result and adds the result to a 40 bit accumulator made up by the 8 Isb bits from the y register and the asrl18 register The least significant 32 bits are also written to the destination register SMAC works similarly but performs an signed multiply and accumulate The MAC instructions execute in one clock but have two clocks latency meaning that one pipeline stall cycle will be inserted if a subsequent instruction tries to use the destination register of the MAC as a source operand Assembler syntax umac__rsl reg_imm rd smac rsl reg_imm rd Operation prod 31 0 rs1 15 0 reg_imm 15 0 result 39 0 Y 7 0 amp asr18 31 0 prod 31 0 Y 7 0 amp asr18 31 0 result 39 0 rd result 31 0 asr18 can be read and written using the rdasr and wrasr instructions Divide instructions Full support for SPARC V8 divide instructions is provided SDIV UDIV SDIVCC UDIVCC The divide instructions perform a 64 by 32bit divide and produce a 32 bit result Rounding and overflow detection is performed as defined in the SPARC V8 standard Watch points The integer unit can be conigured to include up to four hardware watch points Each watch point consists of a pair of application specific registers asr24 25 Yoasr26 27 Yoa
81. y configuration register 2 Memory configuration register 2 is used to control the timing of static ram accesses 31 13 12 987 6 5 4 32 1 0 Not used Bank size Read modify write Ram width Figure 41 Memory configuration register 2 Write waitstates Read waitstates e 1 0 Ram read waitstates Defines the number of waitstates during ram read cycles 00 0 01 1 10 2 11 3 e 3 2 Ram write waitstates Defines the number of waitstates during ram write cycles 00 0 01 1 10 2 11 3 e 5 4 Ram with Defines the data with of the ram area 00 8 10 32 1X 32 6 Read modify write Enable read modify write cycles on sub word writes to 16 and 32 bit areas with common write strobe no byte write strobe e 8 6 Reserved e 12 9 Ram bank size Defines the size of each ram bank 0000 8 Kbyte 0001 16 Kbyte 1111 256 Mbyte Write protection Write protection is provided to protect the memory and I O areas against accidental over writing It is implemented as two block protect units capable of disabling or enabling write access to a binary aligned memory block in the range of 32 Kbyte 1 Mbyte Each block protect unit is controlled through a control register figure 42 The units operate as follows on each write access to RAM address bits 29 15 are xored with the tag field in the control register a

The LEON Processor User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents