Home
12V/10A 12V/20A - Besøg masterpiece.dk
Contents
1. batteries only Do not recharge non rechargeable batteries Charge the batteries only if there is proper ventilation Especially around the batteries While charging a small amount of explosive gasses can be generated in the batteries inadequate ventilation in combination with open fire or sparks can lead to dangerous Situations Do not connect or disconnect the battery while the battery charger is connected to the mains E g to reduce risk of sparking Always disconnect the mains prior to connecting a battery Batteries are capable of providing much energy in a very short time Prevent short circuits any way For example walking over the cables or damaging the cables or connector by improper use Do not shorten the length of the charge cable 3 Mounting and installation The power supply battery charger is not suited for outdoor use Use the battery charger in a dry well ventilated place Keep at least an area of 10cm around the enclosure for proper battery charger cooling During charging the enclosure can become hand warm This is normal The 20A version is equipped with a build in fan operating automatically when the internal battery charger temperature increases For all versions the output power will be reduced in case of insufficient cooling or too high ambient temperatures When charging the time required for the total charge process may increase In power supply mode the maximum output current will be limited For
2. is a class Il appliance double insulated The battery charger complies with the European CE requirements 2 Safety advices This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision Never use the charger in a wet environment for example outside spill fluids over the enclosure or submerge in water Do not use the charger if the cables are damaged the enclosure is open or the charger is damaged in such way that internal parts become accessible lf the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard If the charger is defective do not try to repair it Make sure the charger is positioned stable Keep a free zone of 10cm around the charger to ensure that heat generated during operation can be removed The battery charger is suited for the in Europe standard 220 240V 50Hz mains grid Operating the charger in places where different mains voltages are applicable will damage the charger or render it unsafe Please consult Your supplier in case of doubt Charge specified
3. c GO 12V 10A 12V 20A Power supply and battery charger Instruction manual index C Podu ICS CI ClO eea r E EE E A A a SAVA a EE E E 3 Mounting and installation ccccccsssecccssceccceeeccceeseceeeecceeeueceeeescesseesceseuseceeeaeceseueeessugeeeeeenecetees Ae MOO TATION ccaaresesseeocosesstanassscceseasecsianwensscssecenesn tacossea canada smenaaseaamesans unauhnoutienoseweueeenaiacceesnuoaanawenasees Be Proe ONIE ee E E E dante aantesenseosscneacmaecsiaiee e PEE aO E E E 1 Product description De Go 12V charger series is designed for full automatic supplying a caravan 12V board system and charging Gel and AGM batteries The charger contains the latest state of the art power converter and the charge process is controlled by a microcontroller If the safety precautions in this manual are observed and the charger is operated according to this manual optimal and save charging of the battery is guaranteed The charger consists of 1 A high quality plastic enclosure 2 A battery cable with a 3 pole connector for connecting to the caravan 12V board system a battery and the car 12V supply Supplied with two cables A mains cable for connecting to the public grid 4 Two colored LED s Light Emitting Diodes indicating the operation mode The charger operates full automatically and needs no adjusting Symbols household waste Dispose properly according to the local regulations The battery charger
4. cating the error code Next consult the next tables to diagnose the problem Table 1 Fault diagnostics Problem Possible causes Solution None of the LEDs Check the mains voltage connection are on Car battery voltage too low Check the car battery voltage Consult Your supplier cable broken All LEDs are blinking Problem detected Count the number of flashes between quickly the pauses and consult table 2 Table 2 Error codes Error code s Description Possible causes and solution s 1 2 3 Restart battery charger If the error is repeated problem Consult Your supplier 4 Move to a warmer environment and restart the charging 5 Temperature too high Let the charger cool down for 15 minutes and restart the charging Prevent direct sunlight If the problem persists please consult Your supplier 7 Current too high Cabling problem or other problem Check cabling and connections and restart If unsuccessful consult Your supplier 9 Battery reverse polarity Disconnect the battery and check the polarity If the cause of the failure has been removed the power supply battery charger can be restarted by disconnecting it shortly from the mains 6 Specifications c Go specifications model Supported batteries Battery capacity range Mains voltage Mains frequency Output voltage range Output current range Maximum output power Efficiency Protections Dimensions Charge status indication Use Operational te
5. mperature range Storage temperature Cooling Maximum humidity Safety class Regulations Standards 10A 20A Lead Acid Gel AGM 12V 60 100Ah 90 240Ah 220 240Vac nominal single phase 50 60 Hz 12V nominal O 10A O 20A 150W 240W gt 90 at full load and 230Vac Polarity Output voltage Temperature 210 x 175 x 65mm 2 LEDs Indoor use only 0 40 C 15 50 C Passive Active Fan 95 non condensing II CE LVD EMC RoHS EN60335 2 29 EN55014 1 EN55014 2 At elevated ambient temperatures or if there is no sufficient cooling the output power can be reduced The polarity detection does not detect connecting a reversed polarity battery when the power supply battery charger already is connected to the mains operating as a power supply
6. this reason do not subject the battery charger to direct sunlight Connections The battery charger is equipped with a EU plug for connection to the 220 240V 50Hz mains grid Connect the power supply battery charger to the mains after the battery is connected The output cable has 3 connections Connect A to the battery or caravan board system with one of the two included connection cables Red is positive and black is minus For fixed installations the connection cable with the Ring Tongues are recommended The crocodile clamp connection cable should only be used if a battery outside the caravan should be charged e g at home Connect B to the permanent plus 12V connection of the car Now the power supply battery charger can be connected to the mains Important note Always disconnect the power supply battery charger from the mains if the battery has to be installed or replaced 4 Operation The power supply battery charger operates automatically The operation mode can be read from the LED indications Depending on the installation and the charge level of the battery the following indications can occur LED indication overview Orange LED Green LED Mains Description D a available Off No car connected Power supply battery charger off or car voltage too low Blinking o 2 Caravan battery and 12V board system are slowly slowly supplied from the car Off Caravan battery is charged slowl
7. y No car connected On Caravan battery is charged slowly Car is connected O Ys Caravan battery full No car connected Caravan battery full Car connected o Oon Ys Blinking Blinking Yes A problem occurred quickly quickly See chapter Problem solving 2 seconds on 2 seconds off Y second on second off User tips Prevent deep discharging of the batteries The battery life will be reduced significantly Charge a deep discharged battery as soon as possible Let the battery charger finish the charge cycle completely If the battery is not charged for a longer period for example during winter connect the battery charger to the mains once every month to recharge the battery Battery self discharge and the quiescent current of the connected users will drain the battery charge slowly Do not charge the batteries below 0 C Move the battery to a warmer place and start the charge Keep the ventilation openings clean and free of accumulated dust Blow away the dust and clean the battery charger enclosure eventually with a cloth slightly moistened 5 Problem solving In case there is a problem or there is a suspicion the charger is not operating as expected first check which of the indication LEDs are on If both the orange and the green LED are blinking quickly second on second off followed by a 1 second pause they are indicating an error The number of flashes between the pauses are indi
Download Pdf Manuals
Related Search
Related Contents
Barclay Products 4124-CP Installation Guide do Manual Viewsonic Graphic Series 20” Widescreen Graphic Series LCD E S P A Ñ O L «Dieu de toute éternité, au cours de ma visite à Jérusalem, la "Cité Samsung Galaxy Tab 2 (7.0, 3G) Instrukcja obsługi Copyright © All rights reserved.
Failed to retrieve file