UV Table USER MANUAL
Contents
1. A 96 W 6 T 8 M 312nm 8W 11 2A 2A BTS 26 MS 5 T 8 M 312nm DW FBT 26 S 11 2A 2A 96 W 6 T 8 S 254nm DW 11 2A 2A BTS 26 LS 5 T 8 L 365nm DW FBT 26 S 11 2A 2A 96 W 6 T 8 S 254nm 8W 11 2A 2A A WARNING A UV radiation can be dangerous for unprotected eyes and skin therefore we recommend the user to wear UV protective goggles LP 70 or face shield MP 80 or MP 800 SXT F transilluminator Operating instructions Place your UV Table on a level working surface Plug the unit into a properly grounded electrical outlet To work in reading mode select position 100 then switch on the on off switch To work in preparation mode select position 70 then switch on the on off switch After use switch off the on off switch CAUTION Switch off the fluorescent table when electrophoresis gel is not present on the transilluminator If the filter is too hot it will damage your electrophoresis gel Over 20 minutes transilluminator will be in energy saving mode To activate it again wait for 20 seconds and press switch on NOTE Wait at least 20 second in the 100 position before reducing the intensity selector to 70 If one or several tubes are off or used and in order to keep a better homogeneity UVITEC recommends to change the 6 tubes simultaneously Changing the tubes Before dismantling unplug the UV Table Unscrew the 6 fixing screws on the filter sup2. P 80 or MP 800 BXT F transilluminator Operating instructions Place your UV Table on a level working surface Plug the unit into a properly grounded electrical outlet To work in reading mode select position 100 then switch on the on off switch To work in preparation mode select position 70 then switch on the on off switch After use switch off the on off switch CAUTION Switch off the fluorescent table when electrophoresis gel is not present on the transilluminator If the filter is too hot it will damage your electrophoresis gel Over 20 minutes transilluminator will be in energy saving mode To activate it again wait for 20 seconds and press switch on NOTE Wait at least 20 second in the 100 position before reducing the intensity selector to 70 If one or several tubes are off or used and in order to keep a better homogeneity UVITEC recommends to change the 6 tubes simultaneously Changing the tubes Before dismantling unplug the UV Table Unscrew the 6 fixing screws on the filter support Remove the filter support Change the 6 tubes A quarter turn will release the OH tubes cia zeit IMPORTANT Reassemble the UV table completely St 4 before checking it works correctly Sg i a P To reassemble the UV table follow the
3. REW THE TWO HINGES dl a CAUTION Switch off the fluorescent table when electrophoresis gel is not present The fluorescent table should not be kept On for more than 25 minutes without gel If such is the case switch off the fluorescent table for 20 minutes before a new utilization If the filter is too hot it will destroy your electrophoresis gel All our fluorescent tables are fitted with one or two safety fuses These are found in the plug at the back of the UV table The plugs vary according to the type of UV table and the voltage see the 2 different types below Type of socket and fuse Type of sockets for all models Sockets for all 100V 50 60Hz Type of fuse models except BXT F and SXT F all models PE ay Type FST i d d Time lag T d ay Power See the power values for each item in the spare parts and characteristics board on the last page of the manual Changing the frequency BXT SXT models work at all For other 100V 50 60 Hz models frequency Remove the fuse holder tray Remove the frequency selector located inside Twist a half turn to change the frequency Check that the value visible through the fuse holder tray corresponds to the desired frequency A WARNING A UV radiation can be dangerous for unprotected eyes and skin therefore we recommend the user to wear UV protective goggles LP 70 or face shield M
4. To change the wavelength put the switch to position O After use select position O Changing the tubes a Before dismantling unplug the TABLE b Unscrew the 6 fixing screws on the filter support c d Remove the filter support Change the 6 tubes of the first wavelength and 5 tubes of the second wavelength then the 11 starters starters are located under the tubes only for the BTS A quarter turn will release the tubes and the starters e CAREFULLY keep tubes in the same order see de Medea Med el ed el ed X diagram L BTS 20 LM BTS 26 LM X T 8 M 312nm IMPORTANT Reassemble the transilluminator completely Y T 8 L 365nm peforechecking it Works correctly BTS 20 MS BTS 26 MS X T 8 S 254nm Y T 8 M 312nm To reassemble the transilluminator follow the above BTS 20 LS BTS 26 LS_ X T 8 S 254nm instructions in reverse order Fuses are located in the plug see page 4 Y T 8 L 365nm Spare parts Tubes Filter with Starter Fuse 5x 20 Ref Article Qty Ref Wavelength W support ST 151 230 115v 230 V 100 V Power PP FG 7P 100v 240v 115 V BTS 20 LM 5 T 8 L 365nm 8W FBT 20 S 11 2A 2A 96 W 6 T 8 M 312nm DW 11 2A 2A BTS 20 MS 5 T 8 M 312nm 8W FBT 20 S 11 2A 2A 96 W 6 T 8 S 254nm 8W 11 2A 2A BTS 20 LS 5 T 8 L 365nm DW FBT 20 S 11 2A 2A 96 W 6 T 8 S 254nm 8W 11 2A 2A BTS 26 LM 5 T 8 L 365nm DW FBT 26 S 11 2A 2
5. UVITEC Cambridge EXPAND YOUR TERRITORIES UVItec Ltd Unit 36 St John s Innovation Centre Cowley Road Cambridge CB4 OWS UK Tel 44 0 1223 421270 Fax 44 0 1223 421271 DAMENG E mail uvi uvitec co uk USER WON OS www uvitec co uk 09 2011Index P Table of content LNS le TEE 3 General mpnstruchons EE 4 BXT F transilluminator 5 BTS 2 wavelengths transilluminator EE 6 SXT F transilluminator cccce 7 STS Mixed oto ene 8 STS SOY siderite Cerra 9 ACCESGORIES eessen 10 WARRANTY see 11 UV table You have purchased a new UV transilluminator We are sure it will give you entire satisfaction All our UV transilluminators come equipped with the following UV safety screen total protection for the user against UV rays fully adjustable angle long lifetime Filter unrivalled UV transmitting quality high capacity for absorption of visible light brighter fluorescent response Reflector high reflecting quality to give a perfect diffusion of UV radiation Optic quality 7 Filter support Stainless steel UV intensity selector 2 positions on BXT F and SXT F models position 100 for reading position 70 for preparation Security To prevent an excessive use the transilluminator only BXT F SXT F models will switch OFF automatically after a time from 10 to 15 minutes Warning On the safety a T
6. above instructions in fl e A reverse order Fuses are located in the plug see page 4 H E gt Spare parts Tubes Starter Fuse 5x20 Ref Article Qty Ref Wavelength W Filter with ST 151 230 V 100 V Power support 230 115V 240 V 115 V FG 7P 100v BXT F 15 L 4 T 8 L 365nm DW FBT TC15 CM 4 2A 2A 90 W BXT F 15 M 4 T 8 M 312nm DW FBT TC15 CM 4 2A 2A 90 W BXT F 15 S 4 T 8 C 254nm DW FBT TC15 CM 4 2A 2A 90 W BXT F 20 L 6 T 8 L 365nm DW FBT TC20 CM 6 2A 2A 90 W BXT F 20 M 6 T 8 M 312nm DW FBT TC20 CM 6 2A 2A 90 W BXT F 20 S 6 T 8 C 254nm DW FBT TC20 CM 6 2A 2A 90 W BXT F 20 W 2 T 8 WL White light DW FBT TC20 W 2 2A 2A 30 W BXT F 26 M 6 T 8 M 312nm DW FBT TC26 CM 6 2A 2A 90 W BXT F 26 MX 6 T 8 M 312nm DW FBT TC26 MX 6 2A 2A 90 W BXT F 26 S 6 T 8 C 254nm DW FBT TC26 CM 6 2A 2A 90 W A WARNING A UV radiation can be dangerous for unprotected eyes and skin therefore we recommend the user to wear UV protective goggles LP 70 or face shield MP 80 or MP 800 BTS 2 wavelengths transilluminator Operating instructions Place your transilluminator on a level working surface Check that your electrical supply is compatible with the voltage of your transilluminator Plug the unit into a properly grounded electrical outlet Select the desired wavelength Put the O I switch to the position The switch diode will light up
7. anging the tubes Before dismantling unplug the UV table i a Unscrew the 6 fixing screws on the filter support Remove the filter support Change the 4 tubes and 4 starters starters are located under the tubes A quarter turn will release the tubes and the starters 2252 IMPORTANT Reassemble the UV table completely before checking it functions correctly To reassemble the UV table follow the above instructions in reverse order Fuses are located in the plug see page 4 gt Spare parts Tubes Filter with Starter Fuse 5x 20 Ref Article Qty Ref Wavelength W support ST 151 230 115v 230 V 100 V Power FG 1P 100v 240 V 115 V STS 35 W 2 T 15 WL White Light 15W FS T35 WL 2 2A 2A 80 W 2 T 6 WL White Light 6W 2 2A 2A A WARNING A UV radiation can be dangerous for unprotected eyes and skin therefore we recommend the user to wear UV protective goggles LP 70 or face shield MP 80 or MP 800 ACCESSORIES gt Conversion filter FC 26 WL Converter of UV Light in White Light working area 260 x 210mm Protection LP 70 Goggles for total eye protection MP 800 Face shield for total face and ear protection Other accessories CV 015W Viewing cabinet with internal white light that can be fitted onto a standard large transilluminator for maximum fluorescence in day
8. consumable products or non original spare parts not recommended by our service department is at the user s own risk and therefore automatically invalidates the warranty Tubes filters batteries and consumable products are not included in the warranty We reserve the right to decide where the faulty goods will be repaired in our workshop or elsewhere and whether or not the faulty part is to be replaced all other freight charges incurred being at the cost of the purchaser Returned goods will not be accepted for repair unless previous written authorisation is obtained from our service department A request for authorisation must be accompanied by an itemised list of products model numbers and the corresponding invoice numbers under which they were originally shipped All returned goods should have a certificate of decontamination The Buyer must bear all costs and risks incurred during the transportation of the goods from their collection at UVITEC warehouse In the case UVITEC incorporates some devices or equipment from another supplier in the manufacture of its products the extent and the duration of the warranty will be those conceded by the suppliers or sellers Manufacturer cannot be held responsible for any loss bodily injury or material accident incurred by any failure of this supply whatever the origin of this failure may be The responsibility of Manufacturer is strictly limited to its staff and to its own supplies In the ca
9. erly grounded electrical outlet To work in reading mode select position 100 then switch on the on off switch To work in preparation mode select position 70 then switch on the on off switch After use switch off the on off switch CAUTION Switch off the fluorescent table when electrophoresis gel is not present on the transilluminator If the filter is too hot it will damage your electrophoresis gel Over 20 minutes transilluminator will be in energy saving mode To activate it again wait for 20 seconds and press switch on NOTE Wait at least 20 second in the 100 position before reducing the intensity selector to 70 If one or several tubes are off or used and in order to keep a better homogeneity UVITEC recommends to change the 8 tubes simultaneously Changing the tubes Before dismantling unplug the UV Table Gi Unscrew the 6 fixing screws on the filter support Remove the filter support Change the 8 tubes and 8 starters starters are located under the tubes A quarter turn will release the tubes and the starters e CAUTION Keep the tubes in the same order E ES i es E D ei ege IMPORTANT Reassemble the UV table completely before checking it works correctly Be To reassemble the UV table follow the above instructions in reverse order Fuses are located in the plug
10. his unit must be connected to a wall outlet having protective earth terminal Connecting to ground is an obligatory protection To prevent fire or shock hazard do not expose the unit to rain or moisture Unplug the unit from the wall outlet if you do not use it for a long time Disconnect the power cord by grasping the plug Never pull the cord itself d Never obstruct the air admission grids of the unit b c wa A This symbol is warning against a possible UV radiation Protect the eyes and skin from the UV radiation gt Climatic conditions Altitude lt 2000 meters Operating humidity 20 to 80 no condensation allowed Operating temperature 5 to 33 C General advice To clean the surface of the filter use a mild solvent or warm water Dry with a soft cloth The filter is porous so try to keep it dry Normal cycle using 1 to 25 minutes SPECTRAL CURVES 254 nm 312 nm 365 nm Filter lifetime 2000 hours Unlimited filter life time i see ee life time r Intensity 7 mW cm No 254nm emission guaranteed 9 en SE Intensity 8 mW cm2 ntensity m v cem General instructions ANTI SCRATCH UV SAFETY SCREEN HINGE PIN sl Gy E F A yr S ELE SC ADJUSTING SCREW 4 Re G VC D KH p Kc Af SCREW DRIVER P d ay TO REMOVE THE UV SAFETY SCREEN d Al 2 JUST UNSC
11. light A UV blocking viewing port enables safe viewing of fluorescent objects in the darkroom The lighting 2 x 40W white light enables easy positioning of the object to be viewed CV 415UV UV viewing cabinet with powerful overhead epi UV lights that can be fitted onto a standard large UV transilluminator for very high UV intensity in daylight CV 415 LL 365nm CV 415 LS 365 254nm CV 415 SS 254nm CV 415 LM 365 312nm CV 415 MM 312nm CV 415 MS 312 254nm WARRANTY Our products except Compact Flash light tubes and filters are warranted against faulty construction or defective material for a period of TWO YEARS from the date of supply Our products are not warranted for damage due to carelessness incorrect use or bad maintenance The following defects are also specifically excluded Defects caused by improper operation Repair or modification done by anyone other than UVITEC or an authorised agent Corrosion caused by improper solvents or samples Use of spare parts supplied by anyone other than UVITEC Damage caused by accident or misuse Damage caused by disaster This instrument should not be modified or altered in any way Modification or alteration of this instrument will 1 Void the manufacturer s warranty 2 Void the conformity certifications 3 Create a potential safety hazard The Compact Flash the tubes and the filters are not covered by our warranty The use of
12. port JA Remove the filter support Change the 6 tubes A quarter turn will release the tubes Sa SE EH ai Be IMPORTANT Reassemble the UV table completely pl before checking it works correctly Ag To reassemble the UV table follow the above instructions in reverse order Fuses are located in the plug see page 4 gt Spare parts Tubes Filter with Starter Fuse 5x 20 Ref Article Qty Ref Wavelength Ww Beer ST 151 230 115v 230 V 100 V Power PP FG 7P 100v 240V 115 V SXT F20 L 6 T 15 L 365nm 15W_ FST 20 S 6 3 15A 315A 180W SXT F20 M 6 T 15 M 312nm 15W FST 20 S 6 3 15A 315A 180W SXT F20 S 6 T 15 S 254nm 15W FST 20 S 6 3 15A 3 15A 180W SXT F26 M 6 T 15 M 312nm 15W FST 26 S 6 3 15A 3 15A 180W SXT F26 S 6 T 15 S 254nm 15W_ FST 26 S 6 3 15A 315A 180W SXT F26 MX 6 T 15 M 312nm 15W_ FST 26 MX 6 3 15A 3 15A 180W SXT F36 M 6 T 15 M 312nm 15W FST 36 S 6 3 15A 3 15A 180W SXT F36 S 6 T 15 S 254nm 15W_ FST 36 S 6 3 15A 315A 180W A WARNING A UV radiation can be dangerous for unprotected eyes and skin therefore we recommend the user to wear UV protective goggles or face shield STS Mixed Operating instructions Place your UV Table on a level working surface Plug the unit into a prop
13. se of dispute only the commercial court of Cambridge United Kingdom shall be competent even in third party claims proceedings or when there are several co defendants NOTE UVITEC is not responsible for any injury or damage caused by use of this instrument for purposes other than those for which it is intended or by modifications of the instrument not performed by UVITEC Decontamination collection and elimination of waste The buyer ensures and finances the decontamination the collection and the disposal of waste electrical and electronic equipment WEEE under the conditions provided men in the Articles 21 and 22 of the Decree No 2005 829 dated of 20 July 2005 Improper disposal may be harmful to the environment and human health Declaration of conformity The materials complies with the requirements of the EC Directive 2004 108 EEC 2006 95 EEC and C EN 61010 1 electro magnetic compatibility and low voltage The electro magnetic susceptibility has been chosen at a level that gains proper operation in residential areas on business and light industrial premises and on small scale enterprises inside as well as outside of the buildings All places of operation are characterized by their connection to the public low voltage power supply system
14. see page 4 Spare parts Tubes Filter with Starter Fuse 5x 20 Ref Article Qty Ref Wavelength Ww Support ST 151 230 115v 230 V 100 V Power FG 7P 100V 240 V 115 V STS 20 WS 6 T 8 S 254nm 8W FST 20 WS 6 2A 2A 100 W 2 T 8 WL_ White Light OW 2 2A 2A STS 20WM 6 T 8 M 312nm 8W FST 20 WS 6 2A 2A 100 W 2 T 8 WL_ White Light OW 2 2A 2A STS 20WL 6 T 8 L 365nm 8W FST 20 WS 6 2A 2A 100 W 2 T 8 WL_ White Light OW 2 2A 2A A WARNING A UV radiation can be dangerous for unprotected eyes and skin therefore we recommend the user to wear UV protective goggles or face shield STS 35W Operating instructions Place your UV Table on a level working surface Plug the unit into a properly grounded electrical outlet To work in reading mode select position 100 then switch on the on off switch To work in preparation mode select position 70 then switch on the on off switch After use select position 0 CAUTION Switch off the fluorescent table if not used NOTE Wait at least 20 second in the 100 position before reducing the intensity selector to 70 CAUTION When one or several tubes are out of order the warning tubes flicker for a short moment at the lighting of the UV table Then all the tubes are automatically switched off by the security device For a better homogeneity UVITEC recommends to change the 2 tubes simultaneously Ch
Download Pdf Manuals
Related Search