Turbo Gauge Manual - Leagend: Easier OBD II Diagnostics, Smarter
Contents
1. Turhefloaune MANUAL htto www leagend com 1 Safety Precautions and Warnings To prevent personal injury or damage to vehicles and or the auto computer read this instruction manual first and observe the following safety precautions at a minimum whenever working on a vehicle Always keep attentive while driving DO NOT try to make any adjustments while driving DO NOT mount the auto computer in a position which can obstruct the view of the driver DO NOT mount the auto computer in a manner which could cause it to be propelled through the vehicle during an accident Causing injury such as over or near an airbag DO NOT route the cable in a manner which would interfere with the operation of the vehicle controls Keep the auto computer dry clean free from oil water or grease Use a mild detergent on a clean cloth to clean the outside of the auto computer when necessary 2 Using the Auto Computer 2 1 Tool Descriptions need to change 1 LCD Display Displays retrieved data 2 3 4 5Menu Selection Buttons When there is or icon on the screen next to the button press it to perform what is displayed next to it 6 Button Moves to next screen it is also used to enter time setup screen 7 Button Return to previous screen exit a menu or wake up the tool from sleep mode 8 USB Port Connects the tool to a computer with the USB cable supplied to update the tool 9 10 OBDII Connector Port Conne2. 1 Press the button next to I M to view I M readiness status i DTC I M lt FRZD VIN gt 2 View I M readiness status on screen OK CAT OK HCAT OK EVAP OK AIR 3 Use the upper four buttons next to any of the items or use lower left button to view additional data on next screen s 4 Press lower left button to exit 9 3 Reading Freeze Frame Data Home gt Scan gt FRZD 1 To view freeze frame data press the button next FRZD a DTC aH ZD I M gt VIN gt 2 Use the button next to and to view previous or next PID data RUBIES Ys lt OL Drive gt If there is no freeze frame data available a No FRZD message shows on the screen Press BACK or wait a few seconds to return 3 Press the lower right button to exit 5 4 Viewing VIN Number Home gt Scan gt VIN The tool is able to retrieve Vehicle Identification number on 2002 and newer vehicles that support Mode 9 1 Press the button next to VIN to view vehicle information 4 DTC I M gt lt FRZD VIN gt If the vehicle does not support this mode a Not Supported message comes up on the display Press BACK or wait a few seconds to return 2 View VIN no on screen VIN IHGES16684H88888 3 Press the lower right button to exit 6 CBB Car Black Box Home gt gt CBB gt gt means to press the lower left button The tool is able to save up to 300 hours of your driving d
3. To reset the auto computer to factory defaults oress lower right button from home screen doubly i SPEED DISPLAY K 4 ABOUT DEFAULT K 2 Press the button next to DEFAULT Are you sure a YES NO K 3 Press YES to reset the tool to factory defaults or press NO to exit 9 Appendix 9 1 Appendix 1 GAUGE ABBREVIATIONS SCAN ABBREVIATIONS CLD LP Baani gyen loop status floog Intake Ag T emperaiure e 2 a Fra rusresere ou Joos compres notin hones aerHour 9 2 Appendix 2 Uni Abbrevalion meme ee jiManarumSpeed SIKH KilometerHour Max MHA Mile Hour Max ajCunrentspeed CK KilometerPerHour MPH Mie Per Hour 4 Driving Time ee I d Driving Distance CC BE i S S a S ME E S th oi co ma en en E F 5 i E 2 2 AF S lell Ml EE TT E S E 2 a E l 8 E l S ih d 3 F used since last THIS il I 5 B i Distance emani before tank is eng Tame Diven since last THE Time remaining before tank E emph d Z T ENE j Lh SISI ES ES OS E i Gi Tip Fuel Economy LKS Liter M00 kilometers sIMGS Mie Gallon Gallon 7 Hour Warranty and Service 1 Limited One Year Warranty TurboGauge warrants to its customers that this product will be free from all defects in materials and workmanship for a period of one 1 year from the date of the original purchase subject to the foll
4. by the auto computer by applying this correction A To set the speed accurately you need a handheld GPS One person observes the speed displayed on the GPS and adjusts the percentage till the lower right value agrees with the speed indicated on the GPS while the other is driving Set both the GPS and the auto computer to display the same unit of speed KPH or MPH to make more accurate adjustments B Drive at an auto computer indicated speed of 60 MPH and measure the time between mile marker posts on a highway For every second more than 60 it takes to go 1 mile subtract 1 from the adjustment with the upper left button Repeat this a few times until it takes 60 seconds plus or minus a second to go 1 mile C Use distance measurements to adjust the auto computer and use highway mile markers to check the setting 1 From the home screen press TRIP lt TRIP GAUGES K lt SCAN SETUP K 2 Select CURRENT i CURRENT TODAY K lt TANK TOTAL K 3 Use any of menu selection buttons to select current distance and hold the lower left bottun for about 3 seconds to reset current trip data while passing a mile marker 00 15 15 0M 60MPH 0 8L 4 After passing the mile marker observe the MILES changes on screen and record the indicated distance between two markers 5 Use upper left or right button to adjust the speed in 1 step till the lower right figure agrees with the indicated distance a
5. 4 NORMAL gt SMP Rate SAV K 4 Use the upper left and upper right button to select a sampling rate between NORMAL and SLOW and press SAVE button to save the setup it returns Rate Menu NORMAL is the factory default rate If this causes some updates to be skipped or irregular operation SLOW should be used NORMAL can be used in PWM and all the CAN vehicles and SLOW should be used in VPW ISO and KWP vehicles 5 To change recording rate press the button next to REC RATE i SMP RATE lt REC RATE 6 Use the upper left and upper right button to change and press SAVE button to save the setup and returns to Rate menu lt 3 Seconds K REC Rate SAVE K 8 5 Speed Home gt gt gt gt speed Double press the lower left button will enter the below menu To Do Speed Correction Home gt gt gt gt speed gt Adjust Speed and distance adjustments are used to compensate for changes in tire size gears tire wear etc 1 Press the button next to SPEED si SPEED DISPLAY K ABOUT DEFAULT gt 2 Use the button next to ADJUST to enter speed correction screen lt LIMITED 3 Use the button next to or to adjust in 1 step till the adju stment factor reaches the computed percentage and press SAVE button 10 80 89 SAVE gt The lower left number is the speed reported by the vehicle The lower right number is the speed which is displayed
6. TIME gt a FILLUP RATE K 3 Drive your vehicle normally with the auto computer connected 4 When the tank is around 1 4 full drive to the same gas station use the same fuel pump fill uo the tank at the same rate and let it shut off automatically 5 Press the button next to FILLUP i CBB TIME gt lt FILLUP RATE gt 6 Use the button next to or to change the adjustment factor in 0 1 step till the number to the right of gt agrees with the value reported by the fuel dispenser 1 1 LITRES F lone NO 6 SAVE The number to the left of is the amount of fuel the auto computer believes was used since last fill up the number to the right of gt is the amount of fuel reported by fuel dispenser Before changing the adjustment factor these two numbers should be the same 7 Press SAVE to finish the adjustment and the fuel economy will be immediately affected by the adjustment Record the adjustment factor for your vehicle if you use it in another vehicle and then return it back to this one so you can later adjust it back to this one without repeating the steps above 8 4 Rate Home gt gt Rate 1 Press the lower left button from home screen lt CBB TIME gt i FILLUP RATE K 2 Press the button next to RATE i SMP RATE lt REC RATE 3 To change system management processor rate press the button next to SMP RATE
7. TRIP from home screen lt TRIP GAUGE K lt SCAN SE TUD rs 2 Press the button next to Current to enter current trip screen lt CURRENT TODAY K lt i TANK TOTAL K 3 View detailed trip information on the screen 0 0 LPH 12 5 LK 1 8L 400 KMR Use the upper four buttons next to any of the items or use lower right button to view additional data on next screen s if you want to return or get to the previous page please press the lower right button 4 When viewing current trip information hold lower left button about 3 seconds to reset current trip data manually Reset CURRENT lt YES NO K Only current trip information can be reset 5 Press YES to clear data of current trip or use the button next to NO to exit 3 2 Today Trip Home gt Trip gt Today The Today trip shows the following items 1 Maximum Speed Unit KHM 2 Average Speed Unit KH 3 Driving Time Unit 5 Trip Fuel Economy Unit LK 7 Fule Used Unit L 4 Driving Distance Unit KM 6 Time fuel economy Unit LH g 1 Press the upper left button next to TRIP from home screen lt TRIP lt SCAN GAUGE gt SETUP i 2 Press the button next to TODAY to enter today trip screen CURRENT 4 TANK TODAY K TOTAL K 3 View detailed trip information on the screen 0 0 LPH 1 8L 12 5 LK 400 KM Use the upper fou
8. ata Each itrip record the informtion including the belows Time and date for each trip starts and ends Distance travel each trip Maximum speed during trip Time over speed Number of times of extreme acceleration during trip Number of times of extreme deceleration during trip Number of times of hard acceleration Number of times of hard brake Average Speed 1 Press the lower right button from home screen lt TRIP GAUGE K lt SCAN SETUP amp 2 Press the button next to CBB i CBB TIME gt lt FILLUP RATE gt 3 Select a set of trip information to view lt TRIPI TRIP2 K a TRIP3 TRIP4 i 4 Use lower left button to view detailed trip information Trip Start and Trip End Trip Start gt Mip End E Distance and Max SPD Distance 250Km Max SPD 100KPH i Time Over limitied Soeed 00 00 Over Limitied Speed Number of times of hard brake Number of times of extreme deleration during trip Hard Brakes Ext Brakes Number of times of hard acceleration Number of times of extreme acceleration during trip Hard Acl EKU ACI Average Speed Average Speed 50 KPH jis 5 Press the lower right button it returns to the previous screen 7 Setup Home gt Setup The auto computer allows you to make following adjustments and settings 1 Fuel Selects the fuel type your vehic
9. cts the tool to vehicle s DLC with the OBDII cable supplied 2 2 Specifications 1 Display Backlit 2 lines 16 character display 2 Operating Temperature O to 50 C 32 to 122 F Storage Temperature 20 to 70 C 4 to 158 F Power 8 to 18 volts provided via vehicle battery Dimensions Length Width Height 126 mm 5 in 41 6 mm 1 61 in 26 6 mm 1 05 in 6 NW 0 70kg 1 54lb GW 1 0kg 2 20lb 3 4 5 eS Sr NA NA 2 3 Accessories Included 1 User s manual Instructions on tool operations 2 OBD2 cable Provides power to tool and communicates between the tool and vehicle 3 USB cable Connects the tool to a computer for software updates 4 CD Contains the software update tool user s manual and etc 2 4 Navigation Characters Characters used to help navigate the auto computer are 1 K or lt Indicates the button next to it can be used and presses it to do what is displayed next to it 2 oOr Indicates more information available on previous next screens Pd Identifies a pending code when viewing DTCs 4 Moves to previous digit 5 gt Moves to next digit Indicates an option is selected 6 Increase digit value 7 Decrease digit value 8 Indicates average speed and average fuel consumption 9 gh Indicates oil volume 10 Indicates invalid data 2 5 Connection to the Vehicle Follow the below steps to connect the
10. el Economy Unit LK 1 Press the upper left button next to TRIP from home screen lt TRIP lt SCAN GAUGE K SETUP lt 2 Press the button next to TOTAL to enter total trip screen lt CURRENT lt i TANK TODAY K TOTAL gt 3 View detailed trip information on the screen 0 0 LH 1 8L 56 LK 400 KM Use the upper four buttons next to any of the items or use lower left button to view additional data on next screen s if you want to return or got to the previous page please press the lower right button 4 Gauges The auto computer can be configured to measure and monitor up to four different sets of information simultaneously providing real time engine performance analysis to allow you to adjust driving behavior and improve fuel economy 1 Vehicle soeed KPH MPH 3 Battery voltage VLT 2 Manifold pressure MAP 4 Engine load LOD 5 Fuel Pressure FPR 6 Throttle position TPS 7 Intake air temperature FIA CIA 8 Ignition timing IGN 9 Engine speed RPM 10 Closed open loop CLSD OPEN LP 11 Water temperature FWT CWT 1 Press the button next to GAUGE to view gauge readings lt TRIP GAUGE K lt SCAN SETUPS 2 View currently selected gauges on screen 40 KPH 56 C WT 380 RPM 56 CIA The information available varies from vehicle to vehicle If the information is not available for a certain gauge the trip com
11. le uses 2 Size Sets tank size of the vehicle 3 Engine Sets up engine size 4 Units Changes unit of measure The auto computer uses flash memory to save settings so they will not be lost when the tool is disconnected from the vehicle To enter setup menu Home gt Setup Press the button next to SETUP to perform various setups lt TRIP GUAGE K lt SCAN SETUP ie NOTE In order to get accurate data of fuel consumption distance to empty time to empty and etc always perform vehicle setups if it is the first time to use the auto computer in a vehicle if you use it in another vehicle and then return it back to this one or if you reset the tool to factory defaults 7 1 Fuel Home gt Setup gt Fuel 1 Press the button next to FUEL to enter fuel setup menu a FUEL SIZE K ENGINE UNITS K 2 Use the button on the upper left or upper right to select the fuel type your vehicle uses E GAS gt Fuel Type SAVE K There are DIESELa DIESELb HYBRID GAS LPG fules types to choose as different cars DIESELa and DIESELb do not refer to different tyoes of diesel fuel They only affect the way fuel consumption is computed and are selected based on the way the vehicle computer reports its sensor information Most diesel vehicles use DIESELa 3 Press SAVE button and an icon appears on the screen indicating the type is selected then it returns the Setup Menu 4 HYBRID gt F
12. lect MENU to show 4 menu options in one screen or to set the screen to show current trip information by selecting CURRENT TRIP and press SAVE li is advisable to set the home screen to show current trip information if you use the trio computer in one vehicle only If the trip computer is set to show information of current trip use the lower right button to exit current trip display before viewing other information or performing setups C Enter Contrst Menu 1 To change the contrast of display press the button next to CONTRAST E 3 gt CONTRAST SAVE K 2 Use the button next to or to adjust the contrast and press SAVE 8 7 About Home gt gt gt gt About This function is used to view software version of the tool and look up unit conversions between metric and English unit of measure 1 Doubly press the lower left button from the home menu it will enter the below menu 4 SPEED DISPLAY K lt ABOUT DEFAULT K 2 Use the button next to ABOUT i VERSION CONVERSION 3 Press the button next to VERSION to view software version on screen Version 1 0 2008 TurboGauge 4 Press the lower right button to exit 5 To look up unit conversions press the button next to CONVERSION 3 VERSION a CONVERSION 6 View the conversion results on screen 1 Mile 1 61Km 1Km 0 621Mile 8 8 Default Home gt gt gt gt Default 1
13. nd press SAVE 5 P 60 63 SAVE gt The adjustment does not affect the vehicle soeedometer or odometer readings but the auto computer indicated speed and distance only To Set Speed Limit Home gt gt gt gt speed gt Limited To make the TIME OVER SPEED data in RECORD valid you need to set a speed limit for the vehicle being tested 1 Use the button next to LIMITED 4 ADJUST lt LIMITED 2 Use the button next to or to adjust in IKPH MPH step or use the button next to 10 to change in 10 KPH MPH step till the limit reaches your desired one and press SAVE button 80KPH 410 SAVE gt 8 6 Display Home gt gt gt gt Display 1 Press the lower left button from home screen doubly SPEED DISPLAY K ABOUT DEFAULT K 2 Press the button next to DISPLAY ai MODE HOME gt lt CONTRAST K A Enter Mode Menu 1 To change the display mode of trip items press the button next to MODE lt 2 ITEMS gt Trip Mode SAVE K 2 Use the upper left or upper right button to change between 2 ITEMS and 4 ITEMS and press SAVE and return to Display menu x ITEMS indicates how many items are displayed in one screen when viewing trip information B Enter Home Menu 1 To change the display of home screen press the button next to HOME lt MENU gt Home Page Save gt 2 Use the upper left or upper right button to se
14. owing terms and conditions 1 The sole responsibility of TurboGauge under the Warranty is limited to either the repair or at the option of TurboGauge replacement of the auto computer at no charge with Proof of Purchase The sales receipt may be used for this purpose 2 This warranty does not apply to damages caused by improper use accident flood lightning or if the product was altered or repaired by anyone other than the Manufacturer s Service Center 3 TurboGauge shall not be liable for any incidental or consequential damages arising from the use misuse or mounting of the auto computer Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you 4 All information in this manual is based on the latest information available at the time of publication and no warranty can be made for its accuracy or completeness TuroboGauge reserves the right to make changes at any time without notice 2 Service Procedures If you have any questions please contact your local store distributor or visit our website at htto www leagend com If it becomes necessary to return the auto computer for repair contact your local distributor for more information
15. puter shows When the selected gauges are displayed for about 12 seconds the trip computer records them automatically It show these 4 gauges directly when viewing gauges readings next time 3 Use the upper four buttons next to any of the items or use lower left button to view additional data on next screen s 4 Press the lower right button to exit 5 Scan Tool 5 1 Reading and Erasing Codes Home gt Scan gt DTC 1 Press the button next to SCAN to start scanning lt TRIP GAUGE K lt SCAN SETUP amp 2 Press the button next to DTC to view codes a DTC I M gt 4 FRZD VIN gt If no codes are found the screen will show No Codes Found 3 If more than one code is detected use the button next to and KLO view previous or next codes P1430 ERASE K lt 1 6 gt If a pending code is detected a pd icon appears P2033 Pd ERASE K lt 3 5 gt 4 To erase codes use the button next to ERASE Puss 5 Fd ERASE gt lt 25 gt 5 A warning message comes up asking for your confirmation Erase Codes AYE NUK 6 If you wish to erase codes press YES When codes are cleared successfully an Erase Done message comes up If codes are not cleared a Failed message appears Erase Done lt Back 7 Choose the Back to return the sreen below of 4 8 If you do not wish to erase code press NO button to exit The
16. r buttons next to any of the items or use lower left button to view additional data on next screen s if you want to return or got to the previous page please press the lower right button 3 3 Tank Trip Home gt Trip gt Tank The TANK trip shows the following items Fuel used since last fill up Unit L Distance driven since last fill up Unit KM Distance remaining before tank is empty Unit KM Rg Time Driven since last fill up Unit _ Time remaining before tank is empty Unit k Trip fuel economy since last fill up Unit LK Time fuel economy Unit LH Z Fuel remaining Unit L ih Q JOO ELO M 1 Press the upper left button next to TRIP from home screen a TRIP GAUGE K lt SCAN SETUP i 2 Press the button next to TANK to enter tank trip screen lt CURRENT TODAY K lt i TANK TOTAL K 3 View detailed trip information on the screen 0 0 LH 1 8L 25 LK 400 KM Use the upper four buttons next to any of the items or use lower left button to view additional data on next screen s if you want to return or got to the previous page please press the lower right button 3 4 Total Trip Home gt Trip gt Total The Total trip shows the following items 1 Maximum Speed Unit KHM 3 Driving Time Unit 5 Driving Distance Unit KM 7 Time fuel economy Unit LH 2 Average Speed Unit KH 4 Fuel Used Unit L 6 Trip Fu
17. r s manual for troubleshooting tips Follow steps below to troubleshoot it Verify that the ignition is ON Check if the OBDII connector is connected to the vehicle s DLC well Verify that the vehicle is OBD2 compliant Turn the ignition off and wait for about 10 seconds Turn the ignition back to on and repeat the procedure from step 5 If the auto computer still fails to communicate with the ECU contact the manufacturer or local agent View Mode SETUP 7 When communication has been established it shows the HOME screen GUAGE K SETUP r The HOME screen is defaulted to display 4 menu options as shown in the figure above It can be set to show the CURRENT trip information also HOME screen hereafter in the manual refers to the default setting 3 Trip Computer The auto computer records information about CURRENT TODAY TOTAL and TANK trips 3 1 Current Trip Home gt Trip gt current gt means to press the button next to a or p Displayed data are as follows 1 Maximum Speed Unit KHM 2 Average Speed Unit KH 3 Current speed Unit KPH 4 Driving Time Unit 5 Driving Distance Unit KM 6 Fuel Used Unit L 7 Trip Fuel Economy Unit LK 8 Current fuel economy Unit LPH 9 Distance to Empty Unit KM p NOTE Definition of one trip is the time from when your engine ignition to your engine turn off over 30 minutes 1 Press the upper left button next to
18. screen will retrurn the sreen below of 4 CAUTION Erasing the Diagnostic Trouble Codes may allow the trip Computer to delete not only the codes from the vehicle s on board computer but also Freeze Frame data and manufacturer enhanced data Further M Readiness Monitor Status for all vehicle monitors are reset to Not Ready or Not Complete status Do not erase the codes before the system has been checked completely by a technician 9 Press the lower right button return preivous menu 5 2 Retrieving I M Readiness Status Home gt Scan gt M I M Readiness function is used to check the operations of the Emission System on OBD2 compliant vehicles including the belows 1 Malfunction Indicator Lamp Status MIL 2 Misfire monitoring MIS 3 Fuel System Monitoring Fuel 4 Comprehensive Component Monitoring CCM 5 Catalyst Monitoring CAT 6 Heated Catalyst Monitoring HCAT 7 Evaporative System Monitoring EVAP 8 Secondary Air System Monitoring AIR 9 A C System Refrigerant Monitoring ACRF 10 OXygen Sensor Heater Monitoring O28 11 Oxygen Sensor Heater Monitoring HTR 12 EGR System Monitoring EGR Besides the below world show these monitors status OK Indicates that a particular monitor being checked has completed its diagnostic testing NC Indicates that a particular monitor being checked has not completed its diagnostic testing NA The function is not supported on that vehicle
19. screen of the tool Default Resets all units engine displacement engine type tank size gauge settings trio data and screen settings to manufacturer defaults 8 1 CBB Home gt gt CBB See the item 6 8 2 Time Home gt gt Time 1 press the lower left button from home screen iCBB TIME K lt FILLUP RATE K the home screen is set to display information of current trip Press the lower right buton to enter HOME screen first then from home screen to Tool Informations 2 Press the button next to TIME 20260 28 2007 08 20 3 Press the lower left button to enter time adjustment screen 20 26 28 2007 08 20 4 Use the button next to lt or to select a digit and then use the button next to or to increase or decrease value 5 Press the lower left button to finish and save the setup or press the lower right button to exit without saving the settings 8 3 Fill up Home gt gt Fillup NOTE In order to get more accurate fuel consumption readings and to get valid TANK information use the FILLUP function every time when your vehicle is refueled Make sure the tank size and the fuel type are properly set before use this function 1 Fill the tank in gas station and let the pump shut off automatically 2 Press the button next to HLLUP and press SAVE without adjusting the indicated fuel on the first after connecting the trip computer to the vehicle iCBB
20. tool to the vehicle 1 Connect the OBD II cable to the tool 2 Place the tool to the position you have chosen 3 Locate DLC on vehicle The DLC Data Link Connector or Diagnostic Link Connector is a standa rdized 16 cavity connector where diagnostic auto computers interface with the vehicle s on board computer The DLC is usually located 12 inches from the center of the instrument panel dash under or around the driver s side for most vehicles If Data Link Connector is not located under dashboard a label should be there telling location For some Asian and European vehicles the DLC is located behind the ashtray and the ashtray must be removed to access the connector A plastic DLC cover may be found for some vehicles and you need to remove it before plugging the OBD2 cable If the DLC can not be found refer to the vehicle s service manual for the location 4 Pug OBD II cable to the vehicle s DLC 5 Turn the ignition on Engine can be off or running 6 The auto computer starts to communicate with the vehicle if the auto computer fails to communicate with the vehicle s ECU Engine Control Unit a Link Error message shows as below Link Error lt AGAIN Use the button next to AGAIN to try to connect to the vehicle and the tool re attempts to communicate with the ECU If there is still no communication between them a CHECK MANAUL message comes up prompting you to refer to the tool s use
21. uel Type SAVE K 7 2 Tank Size Home gt Setup gt Size 1 Press the button next to SIZE to set the tank size of your vehicle a FUEL T lt 4 ENGINE UNITS gt 2 Use the button next to or to change the tank size and press SAVE button to save then it returns the Setup Menu 56 LITERS Tank Size SAVE 7 3 Engine Home gt Setup gt Engine 1 Press the button next to ENGINE 4 FUEL lt ENGINE SIZE gt UNITS K 2 Use the button next to or to change engine size and press SAVE button then it returns the Setup Menu 2 4 LITRES ENGINE SAVE K 7 4 Units of Measure Home gt Setup gt Units 1 Press the button next to UNIT to change units of measure al FUEL ENGINE SIZE K UNITS gt 2 Use the upper left or upper right button to change between metric and English unit of measure and press SAVE then it returns the Setup Menu lt METRIC Units gt GAVE K 8 Tool Information Tool information includes the follows 1 Record The Trip Recorder please see the previous item 6 Speed adjust and limit the speed 2 3 4 5 6 7 About The version and conversion 8 Time Changes time displayed by the auto computer FILLUP Used to refuel the vehicle every time Rate Sets sampling and recording rate Display Sets contrast display mode and home
Download Pdf Manuals
Related Search