Home

RFFS-100 USER MANUAL

1. Place the actuator in the hole and hold in place with a scrap balsa wedged in the clearance gap Adjust the actuator position to where it is parallel and centered before gluing in place MAGNET INSTALLATION Clean the magnet Strip the insulation off a 1 piece of blue wire Bend one end to match the curve of the magnet and then a sharp right angle at the end of the curve as below Apply thick Ca glue on the wire around the magnet and hit it with the zip kicker Bend the remaining part of the wire as below With the magnet centered in actuator push the end of the wire into the control surface This should hold it in place well enough to glue it with a tiny dab of thick Ca glue on either side of the control surface Make sure the flats of the magnets are fore amp aft D ht Je Control Surface Now make any adjustments to center the magnet in the coil by bending the wire Be sure to use non magnetic tools MOTOR AND BATTERY PREP MOTOR Cut 2 blue wires about 4 5 for thistles or 3 25 for Lil Skeeter Strip 4 of insulation off one end and 1 8 off the other Solder the 1 8 ends to the motor terminals The 4 ends push into the control module at final assembly For a KP00 replace the heavy wires and cut the plastic tabs off BATTERIES Cut a red wire about 2 25 for the terminal and a 1 black for the minus Strip 4 of insulation off one end and 1 8 off the other Cut the terminal tab on one battery and the mi
2. 310 SACI anys pue jppes SUIM U ONM poquq UOneLIO 1293 SuIpueT SN APJA uo p310 109 yous ese Ce T JOJADTY JO Joppny pwg Jaqqny CEO LAV Y AAO AAV SLVTA LAN VN 939N IOWAJA IO Joppny 0 poyorye Ia SEIN deny a30uEIEOIH pwg Jo0OTt 3 CG EU gt be ded 91 1 Dau enen A0 7007 I4s14AdoD yoys ese CC QUIS ZIOY 10 IA xxx UAC S AALAAMS TIT LON SI STHL A INO SASOdANd AONANAAAA WON xxx 13u 2 UMOp sooisop ISNIY L Pan VWE A W109 AUAOIS AAA i1 ays d AUCH TAIM Cras TIVL OAC SOINOYLOYTA 91 1 Les woNeso 193 Surpue y coun mo 310909 eon ee SJo s IJU MIx uone EE E EE EE IO E A Sea Rae a A PoJLOIPUL SIO M SSOUYITY JOO Pete Ia CE 79 0N S I TVACHHIG OTO TAIM dv NOILVOOT ara Dau enen A0 7007 107
3. RFFS 100 USER MANUAL Voltage Input 1 5V to 5 5V 2 to 4 cells or 1 lithium Weight 1 8 grams Channels Throttle rudder and elevator Receiver Band 72 Mhz CH s 11 60 Mode FM negative shift Bandwidth 76 KHz Current Draw 015A motor micro servos 2 servos at full throw Amps Batt V 50 ESC Amps 1A Max Servo Coil Ohms 25 or greater Dynamics Unlimited issue 50 Ohms 5 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation RFFS 100 Hook Up ke CO COD DH Y Aan bei SE ECKE 4 580 wl 3850 Hes slowfly com 0 000 1 340 RFFS 100 HANDLING ETIQUETTE The RFFS 100 is built for extreme lightness Care must be taken when handling First the board is 010 thick It s still pretty tough but not like 062 circuit boards Second the board has no protective covering Care must be taken not to let a dangling battery wire contact the board other than the battery lead sockets Also proper etiquette should be observed when handling the RFFS 100 unit When setting the unconnected unit down metal surfaces should be touched first When picking up metal surfaces should touched first with one hand before the other touche
4. nus terminal on the other battery to where they extend 1 4 beyond their outside diameter With a hot clean iron tin both sides of the 4 part of the tab being careful not to melt the plastic cover on the end of a battery If it does melt it may short the battery Now clean the tip of the iron and solder the two batteries together Cut the other tabs to about Li or longer if preferred and solder the longer red wire to the and the short black wire to the minus The 1 4 ends push into the RFFS 100 at final assembly Fort cells LU A little additional info Be careful connecting the battery Double check the polarity before connecting There is no reverse polarity protection The red dot on the receiver is positive There is also a sign on the board To turn the receiver on and off I just plug the positive wire in and out of the receiver Just be careful when it s out that it doesn t make some unplanned contact with the receiver in a bad place The yellow wire is for the antenna I recommend going to the local music store and buying a 010 to 013 diameter guitar string and turning it into a 15 whip You can solder a short piece of the yellow wire to it to plug into the RFFS 100 Be sure to put a small piece of balsa on the end for eye protection Glue hint I put a large drop of Ca glue on a piece of poly plastic a baggie will do and then use a piece of wire to transfer from the drop to what is being glued The best par
5. s the unit When handing the unit to your envious friend touch him first with one hand before he grabs it out of your other hand And touch him first before you wrestle it back After the unit is installed first contact should be either the batteries motor of the left side of the unit as shown above at or near the sockets Do not panic The above dissertation is mostly important in low humidity seasons or locations when static sparks are flying The board was designed with an embedded ground plane around the circuitry and components on both sides along with very short runs This makes the RFFS 100 very tough to static discharge but the above information will help you not test it e eg WHAT ELSE DO YOU NEED 1 32 1 16 and 1 8 contest balsa Kenway KR1 D or KP00 motor and Union 80 prop Two or three 50 ma hr batteries 2 cells amp KR1D 6 minutes 3 cells amp KP00 aerobatics CA thin glue thick glue and zip kick Soldering Iron Stainless steel tweezers or plastic tweezers non magnetic tools Brass 3 8 tube for cutting actuator holes ACTUATORS ACTUATOR INSTALLATION Once the hinges and control surfaces are in place before they are attached to the airframe use a 3 8 diameter brass tube local hobby supply sharpened at one end to cut a hole for the actuator Be sure to have the brass tube centered on the 1 16 gap before cutting Now carefully cut an extra 1 32 to 1 16 off the control surface side for a clearance gap
6. t is when you forget about it and you spend the rest of the day with people asking you why that baggie is stuck to your arm IMPORTANT The RFFS 100 s software will automatically detect transmitter types Hitec Futaba JR or Airtronics In order for the automatic detection to work it is important that power to the transmitter is on before power is applied to the receiver The throttle also should be in the off position when the receiver is powered up THINGS THAT MAKE IT WORK e The coils must absolutely be centered on the effective axis e Keep the glue off where the rubber hinges bend e Keep at least a 1 16 inch space for the rubber hinge to bend e Magnet flat sides should be fore and aft Have Fun DWE www smallrc com Stoot oyouZew uou ISN 0 ANS Og OITA o4 SuIpusg Aq 109 y UI Joe oY 194U99 0 sjuouNsn pe Aue ae MON d9dBJINS ONUOD oY JO Opts at UO an BD J01 JO qep Aun e YIM y an 0 YSnoud Jam ad UL 1 Pio prnoys SLL sovZNs ToUOS OY OFUT OITM OY FO Dua oy Ysnd 10N UT p9197U99 ouseU 201 0 IJ MS 0U UMOS se OTM oy JO Wed Sura oy puog RES diz ou YIM 1 10 pue qep oy UO onm oy Jo Hed posna oy Jos ouseUT oy Jo a8po oy UO an BD Jop Jo qep B Md MOTAQ SB 9AIND I JO Dua au 12 au 14311 dieys g uoy pue jouseul oY FO SAINI OY YOU 0 pu oUO JO 8 1 Dua M DMV 87 Jo 291d I 2 UO uoneqsur oy ding jouseu 20 WO NOILV TTYLSNI DINN IMPON 0u ei 0 UE 10

RFFS-100 USER MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents