Optical Modulator Remote Commands - Electro
Contents
1. After the input has been completed press the OK or ENTER key SYSTEM 24 Date Time Network Set Trigger Password Condition Check GP IB Address Display Screen Note In this Chapter keys are indicated as described below e Hard key e Parameter item e Function key lt gt 2 1 Uonoeuuo JO suopesedasd ne 2 2 Connecting through Ethernet 2 2 Connecting through Ethernet 2 2 A different address needs to be set for the network address of each unit in order to identify the unit to be connected to the network Follow the steps below to set the network address 1 Press the SYSTEM key to display the system screen 2 With the A or W key move the cursor to Network Set and press the lt Edit gt or ENTER key 3 With the A or W key move the cursor to IP Address SubNetmask or Gateway and press the lt Edit gt or ENTER key to select it 4 With the ten key pad or the A or W key change the numeric value and press the OK or ENTER key 5 Repeat steps 3 and 4 to input all parameters IP Address SubNetmask and Gateway 6 After all parameters have been input press the lt Close gt or CANCEL key 7 To make the set numeric values valid turn OFF the power and turn it ON again SYSTEM IP Address Date Time GP IB Address Network Set Trigger Password Condition Check Network Address Display Screen Note For IP Address S2. Contents Execution error Remedy Check the command and send it again Type EXE 1034 Message Data out of range Contents Data is beyond the setting range Remedy Check the setting range and send the command again Type EXE 1036 Message Queue Overflow Contents Error queue overflow Remedy Read out the error or clear the error queue Type DDE 1037 Message Query Error Contents Query error Remedy Check the command and send it again Type CME 1M810518802 17E 5 1 siog puewwog 9joul9yJ e 5 1 Remote Command Errors Remote Command Errors 2 2 Code Item Description 2031 Message Invalid update memory Contents Update Memory of the Firmware is faulty Remedy Update the firmware again Type DDE 2032 Message Invalid ID information memory Contents Update Memory of the Firmware is faulty Remedy Hardware is faulty Type DDE 2033 Message Temperature limit error Contents Temperature error is detected Remedy Check whether or not the temperature of the installation place is too high Type DDE 2036 Message A D timeout error Contents AID conversion is failed Remedy Hardware is faulty Type DDE 5 2 1M810518802 17E 6 1 Troubleshooting Chapter 6 Troubleshooting 6 1 Troubleshooting 1 The setting does not become valid even though the setting command is sent Send SYST ERR command to check the error contents After that send the correct command Example Parameter value beyond the setting range is specified SOURS AMPL
3. parameters state Type discrete Range POS NEG POS Auto Bias Control is locked on the Positive side NEG Auto Bias Control is locked on the Negative side Default POS example SOUR ABC SLOP POS ll SOURce n ABC SLOPe description Obtains the set slope value of the Auto Bias Control response state Type discrete Range POS NEG ll SOURce n ABC RESet description Resets the Auto Bias Control forcibly example SOUR ABC RES ll SOURce n BIAS syntax SOURCe n BIAS bias description Sets a DC Bias of the LN However this setting cannot be made when SOUR ABC STAT is set at ON parameters bias Type decimal Range 10 00 to 9 90 0 01V Step Default 0 00 example SOUR BIAS 10 00 ll SOURce n BIAS description Obtains the set DC Bias value of the LN responese lt bias gt Type decimal Range 10 0 to 9 90 0 01V Step 1M810518802 17E ll SOURce n AMPLitude syntax description parameters example SOURCce n AMPL itude amplitude Sets an output amplitude of the driver amplitude Type integer Range 0to255 1Step Default 180 Optional setting is 1 5m and X cut 160 Optional setting is 1 5um and Z cut 150 Optional setting is 1 3um and X cut 130 Optional setting is 1 3m and Z cut SOUR AMPL 180 ll SOURce n AMPLitude description response Obtains the set output amplitude value of the driver amplitude Type integer Ra
4. 300 Parameter value beyond the range is set SYST ERR 1034 Data out of range SOUR3 AMPL 200 Parameter value within the range is set SYST ERR 0 No Error 2 Command process time According to the command it takes a long time to make the setting causing Timeout Error to occur If this occurs wait for enough time after the command has been sent and send the next command or send the next command after the command has been completed by the OPC command Bunoouse qno B Example The completion of the command is checked with SLOT OPC command SOUR3 AMPL 150 SLOT3 OPC 0 SLOT3 OPC 1 SOUR3 AMPL 200 The following shows the response of SLOT OPC command 0 Command is being processed 1 Command process is completed 1M810518802 17E 6 1 Appendix 1 List of Commands Appendix 1 List of Commands Common Commands Command Description Page SLOT n IDN Obtains the module information 3 1 SLOT n OPC Obtains the command processing status 3 1 SLOT n OPTions Obtains the module information 3 1 SLOT n PRESet Returns the set information to its factory default setting 3 1 SLOT n TST Obtains the self test results 3 2 Unit Specific Commands Command Description Page STATUS n Obtains the alarm information 4 1 SOURce nABC S TATe Sets the Auto Bias Control to ON or OFF 4 1 SOURce n ABC STATe Obtains the set valu
5. If the value is not 0 the bit value corresponding to the fault item becomes 1 Bit Bit Item Name 0 Upgrade Memory error 1 ID Information Memory error 2 Temperature alarm 6 3 Not used T AID error 3 2 1M810518802 17E 4 1 Unit Specific Commands Chapter 4 Unit Specific Commands 4 1 Unit Specific Commands This Chapter describes the function commands of the AQ2200 621 622 ll STATUS n description Obtains the alarm information response lt alarm gt Type integer Bit Item Name Obtained Value 1 0 Temperature alarm 00 Correct status 01 The temperature exceeds the upper limit of the operating temperature This may cause an operational fault 2 ABC alarm 0 Correct 1 Faulty ll SOURce n ABC STATe syntax SOURCe n ABC STATe state description Sets the Auto Bias Control to ON or OFF parameters lt state gt Type discrete Range OFF ON OFF Auto Bias Control is stopped ON Auto Bias Control is operated Default ON example SOUR ABC STAT ON ll SOURce n ABC STATe description Obtains the set value of the Auto Bias Control response state Type discrete Range OFF ON 1M810518802 17E Spueululo aads yun B 4 1 Unit Specific Commands 4 2 ll SOURce n ABC SLOPe syntax SOURCe n ABC SLOPe state description Sets a slope of the Auto Bias Control However this setting cannot be made when SOUR ABC STAT is set at OFF
6. Remote Control Functions eeseeessesssssuss 1 1 1 4 Command Format sess emeret i E e a nnn a nnn na 1 2 Preparations for Connection 2 1 Connecting through GPeIB aeui rhe neben veece Eo pte ba lesen ien pua 2 1 2 2 Connecting through Ethernet coat e E bp ets tutbe edt ob qao edo e cede 2 2 Common Commands 3 1 Common Gomrmnatids ase tee diete tee eorr on tse A een xxr ect trenta 3 1 Unit Specific Commands 4 1 Unit Specific Commands sessssssssssssssssssseeeeee eene mener 4 1 Remote Command Errors 5 1 Remote Command Errors cccccccccccccceccceccceeceeeeeeeeeeceeeceeeeeeaeceaeeeaeeeaeeaas 5 1 Troubleshooting 6 1 Troubleshooting rrr eer n pee gre rc KIKI Prae EE T Ree MGR 6 1 Appendix 1 List of Commands ssssssssseeene Appendix 1 1M810518802 17E iii 1 1 Overview 1 2 Connections 1 3 Specifications of Remote Control Functions Chapter 1 Functional Description 1 11 Overview This remote control function remotely controls the AQ2200 series Frame Controller using an external controller such as personal computer through the GP IB or Ethernet interface This user s manual describes the remote control functions of AQ2200 621 622 10Gbit s Optical Modulator 1 2 Connections For details about connections see the Remote Command Reference for AQ2201 AQ2202 Frame Controller 1 3 Specifications of Remote Control Funct
7. aan Model 810518802 AQ2200 621 622 10Gbit s Optical Modulator Remote Commands YOKOGAWA IM 810518802 17E Yokogawa Electric Corporation 1st Edition Introduction Notes Trademarks Revisions 1st Edition March 2005 YK Thank you for your purchasing of this AQ2200 621 622 10Gbit s Optical Modulator This User s Manual for remote command describes the following interface functions and their related commands e GP IB interface e Ethernet interface Before starting operation of this module thoroughly read this manual to use the product properly After reading this manual always store it in a safe place where all concerned personnel can refer to it immediately This manual is useful if the operator have forgotten proper operation steps during operation In addition to this manual two kinds of manuals shown below are provided for the AQ2200 621 622 Therefore you need to read the following two manuals as well as this user s manual Manual Item Manual No Description AQ2200 621 622 IM810518802 01E This manual describes all functions of the AQ2200 621 622 10Gbit s Optical except for the communication functions and proper operating Modulator procedures User s Manual AQ2200 621 622 IM810518802 17E This user s manual The manual describes the communication 10Gbit s Optical functions remote control functions of the AQ2200 621 622 Modulator Remote Commands User s Manual Additionally you must also
8. e lower case character portion can be omitted Example SYSTem e Correct description SYSTem SyStEm SYST sysTEM syst SYSTEm SYSTeM System sYSTEM syST etc e Incorrect description SYSTe SYS SYSTemm syste etc Items described in lt gt in the syntax and response of the command show parameters Parameter name is described in lt gt Example syntax SOURCce n ABC STATe state parameters lt state gt response lt status gt If there are multiple parameters they are separated by a comma Example response lt Manufacturer gt lt Model gt lt Serial Numbers gt lt Firmware Revision gt There are also commands which do not have any parameters Example SLOT n IDN Items that I is described in Range of the parameter show that one element is selected from those listed A B 7 Either A or B is selected Example Range OFF ON For details see the Remote Command Reference for AQ2201 AQ2202 Frame Controller 1M810518802 17E 2 1 Connecting through GP IB Chapter 2 Preparations for Connection 2 1 Connecting through GP IB 1M810518802 17E When connecting multiple units a different address needs to be set for the GP IB address Follow the steps below to set the GP IB address Press the SYSTEM key to display the SYSTEM screen With the A or W key move the cursor to GP IB Address and press the Edit or ENTER key With the ten key pad or the A or V key change the address
9. e of the Auto Bias Control 4 1 SOURce n ABC SLOPe Sets a slope of the Auto Bias Control 4 2 SOURce n ABC SLOPe Obtains the set slope value of the Auto Bias Control 4 2 SOURce n ABC RESet Resets the Auto Bias Control forcibly 4 2 SOURce n BIAS Sets a DC Bias value of the LN 4 2 SOURce n BIAS Obtains the set DC Bias value of the LN 4 2 SOURce n AMPLitude Sets an output amplitude of the driver 4 3 SOURce n AMPLitude Obtains the set output amplitude value of the driver 4 3 SOURce n CROSs Sets a cross point of the driver 4 3 SOURce n CROSs Obtains the set cross point value of the driver 4 3 1M810518802 17E Appendix 1 A xe xe xipueddy
10. ions The following shows the specifications of the GP IB and Ethernet remote control functions Specifications of GP IB remote control function Item Specifications GP IB address Delimiter code 0 to 30 Default value 20 EOV is put at the end of the data Specifications of Ethernet remote control function Item Specifications IP Address shows a numeric value ranging from 0 to 255 Factory default setting 192 168 1 1 SubNetmask gt shows a numeric value ranging from 0 to 255 Factory default setting 255 255 255 254 Gateway 55 shows a numeric value ranging from 0 to 255 Factory default setting No default setting Port No 0 to 65535 Factory default setting 50000 Communication protocol TCP IP Delimiter 1M810518802 17E With Client Server Model Frame Controller functions as Server CRLF 2 bytes 1 1 uonduoseq jeuonoun fe 1 4 Command Format 1 4 Command Format 1 2 1 2 3 4 5 6 When the frame No slot No and device No are specified this manual describes each No as shown below Frame m Frame controller 0 Slot No n AQ2201 1t03 AQ2202 1t09 The command in the portion enclosed by can be omitted When the frame No m is omitted the frame No becomes 0 When the slot No n is omitted the slot No becomes 1 Example SLOT n IDN STATUS n etc When describing a command th
11. nge 0to255 1Step ll SOURce n CROSs syntax description parameters example SOURCe n CROSs lt crosspoint gt Sets a cross point of the driver lt crosspoint gt Type integer Range 31 to 32 1 Step Default 0 SOUR CROS 20 ll SOURce n CROSs description response 1M810518802 17E Obtains the set cross point value of the driver lt crosspoint gt Type integer Range 31 to 32 1 Step 4 1 Unit Specific Commands 4 3 SPUBWWO oads Pun B 5 1 Remote Command Errors Chapter 5 Remote Command Errors 5 1 Remote Command Errors This Chapter describes errors that occur when using the remote command The following shows the error messages caused by the remote command For details about other errors see the list of error codes stated in the Operation Manual for AQ2200 multi application system Additionally the flag set information on standard status and register is described in Type CME Command error EXE Execution error DDE Device error QYE Query error Remote Command Errors 1 2 Code Item Description 1030 Message Command Error Contents Command error Remedy Check the command and send it again Type CME 1031 Message Syntax Error Contents Syntax error Remedy Check the command syntax and send the command again Type CME 1032 Message Parameter Error Contents Parameter error Remedy Check the command parameter and send the command again Type CME 1033 Message Execution Error
12. read the manual for AQ2201 AQ2202 Frame Controller a main unit on which the AQ2200 621 622 is to be mounted Furthermore when performing the BER measurement of the 10Gbit s band optical interface by combining optional units such as BERT module 1 light source module 2 and optical receiving module 3 of the AQ2200 series thoroughly read relevant manuals 1 AQ2200 601 10Gbit s BERT Module 2 AQ2200 111 DFB LD Module 3 AQ2200 631 10Gbit s Optical Receiver The contents of this manual are subject to change without prior notice as a result of continuing improvements to the instrument s performance and functions The figures given in this manual may differ from the actual screen Every effort has been made in the preparation of this manual to ensure the accuracy of its contents However should you have any questions or find any errors please contact your nearest YOKOGAWA dealer Copying or reproducing all or any part of the contents of this manual without the permission of Yokogawa Electric Corporation is strictly prohibited This unit uses Montavista Linux Montavista is a registered trademark or trademarks of Montavista Software Inc Linux is a registered trademark or trademarks of Linus Torvalds in the United States and or other countries Adobe and Acrobat are trademarks of Adobe Systems Incorporated In this manual TM and marks are not indicated on the registered trademarks and or trademark
13. s of their respective companies Other company and product names mentioned herein may be the trademarks of their respective owners 1st Edition March 2005 All Rights Reserved Copyright 2005 Yokogawa Electric Corporation 1M810518802 17E i How To Use This Manual Structure of This Manual This user s manual consists of the following sections Chapter Title Description 1 Functional Description This Chapter describes the overview specifications and command format of the remote function of this unit 2 Preparations for Connection This Chapter describes how to set up the GP IB and Ethernet interfaces of this unit 3 Common Commands This Chapter describes the commands common to all AQ2200 series modules 4 Unit Specific Commands This Chapter describes the function commands specific to this module 5 Remote Command Errors This Chapter describes the errors that occur when using the remote commands 6 Troubleshooting This Chapter describes the troubleshooting procedures Appendix This Appendix describes the list of commands of this module ii 1M810518802 17E Contents Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 5 Chapter 6 Appendix Introd ctoN RE TARTE CT DD TIEREN i HowTo Use This Mariual 3 AA ha ba WADI Aika li Functional Description TA 37 gt 071 WA AA WE WA ahu 1 1 1 2 GOnDnecllons oeste Deed e eo Ee ie ieee Sora av eae Seda Os 1 1 1 3 Specifications of
14. ubNetmask and Gateway of Network Set items the numeric values you have input become valid after the power has been turned OFF and it has been turned ON again Power OFF ON The previous status is retained unless the power is turned OFF and it is turned ON again 1M810518802 17E 3 1 Common Commands Chapter 3 Common Commands 3 1 Common Commands This Chapter describes the commands common to all modules JJ SLOT n IDN description Obtains the module information response lt Manufacturer gt lt Model gt lt Serial Numbers gt lt Firmware Revision gt example SLOT IDN YOKOGAWA AQ2200 621 81D300041 01 00 ll SLOT n 0PC description Obtains the command process status response status Type integer Range 01 0 Process is in progress 1 Process is completed ll SLOT n OPTions description Obtains the module information response option Type integer Bit Bit Item Name Value 1 0 Wavelength 00 1 5um 01 1 3um 2 LN Type 0 Z Cut 1 X Cut 3 Not used 0 ABC Bias Point 0 Center 7 5 Not used 0 example SLOT OPT gt 4 JJ SLOT n PRESet description Returns the setting information to the factory default setting status 1M810518802 17E 3 1 SpueuluJo UOWWUOD n 3 1 Common Commands ll SLOT n TST description Obtains the self test results response lt result gt Type integer Range 0 Correct Value other than 0 Faulty
Download Pdf Manuals
Related Search