PM-200A - B&H Photo Video
Contents
1. 2 internal speakers 2 external 1 4 outputs 2 x 50W RMS 80 Total 100W RMS 2 x 75W RMS 40 Total 150W RMS Frequency Response 20Hz 50KHz THD 0 055 S N 81dB Noise Floor 200uV Amplifier protection clipping LEDs thermal runaway short circuit anti thump on off protection Internal Speakers Impedance Voice Coil diameter 1 5 full range 8 O Power Requirements Selectable 115VAC 60Hz or 230VAC 50Hz Fuse Requirements 5x20mm glass tube F B 6A 250V 115VAC 3A 250V 230VAC Weight 9 6 lbs 4 4 Kg et CAR Ko 28 x 18 x 15 5 cm Dimensions HWD Specifications subject to change at any time without prior notice for purposes of product improvement ONE YEAR LIMITED WARRANTY Nady Systems Inc warrants to the original consumer purchaser that the unit is free from any defects in material or workmanship for a period of one year from the date of original retail purchase If any such defect is discovered within the warranty period Nady Systems Inc will repair or replace the unit free of charge subject to verification of the defect or malfunction upon return to Nady Systems Please do not return your Nady product to the store where it was purchased as Nady Systems handles your warranty service directly Communication with our Service Department is the most efficient means of servicing your unit and we are dedicated to keeping you a satisfied customer To the extent permitted by law any applicab2. Nady Systems will inform the buyer if product sent in does not meet the terms of this warranty and will provide a quote for fixing the unit and or shipping it back exclusively at the buyer s expense SERVICE FOR YOUR NADY AUDIO PRODUCT In the U S If you are experiencing operational problems with your system please refer to the Support page at www nady com for assistance Should your wireless system require service please contact the Nady Service Department at 510 652 2411 for a Return Authorization R A Number and service quote if out of warranty Make sure the R A Number is clearly marked on the outside of the package that you are returning If your unit is out of warranty please enclose a cashier s check or money order or pay by credit card per instructions by the Nady Service Department Ship your unit prepaid to Nady Systems Service Department 6701 Shellmound Street Emeryville CA 94608 Include a brief description of the problem you are experiencing For service of a unit under warranty please follow the instructions in the following section Outside the U S For service or warranty matters please contact the Nady distributor in your country through the dealer store from which you purchased this product Do not attempt to service this unit yourself as it can be dangerous and will also void the warranty amo DOT CGC gt NADY SYSTEMS INC 6701 SHELLMOUND STREET EMERYVILLE CA 94608 Tel 510 652
3. level signals Make sure to turn down the preceding unit to avoid distortion The XLR jack is configured for Pin1 ground Pin2 positive Pin3 negative Note the Mic input is more sensitive than the Line input INPUTS The 14 TRS LINE input is designed to accept balanced or unbalanced linelevel signals such as those from keyboards drum machines or samplers If a balanced signal is to be connected to the line input then a 1 4 TRS stereo phone plug should be wired for Tip positive Ring negative Sleeve ground Note Both Mic input and Line input can be used simultaneously if desired however audio levels cannot be adjusted separately 2 LINE OUT This 1 4 unbalanced output can be used to daisy chain multiple PM 200A or O send the input signal directly to a mixer PA system or recording device The Line Output is not affected by the Volume controls or EQ 3 VOLUME This adjusts the signal level sent to the internal speakers external speaker and headphone outputs VOLUME MAKE SURE TO AVOID EXCESSIVE CLIPPING OF THE POWER AMPLIFIER The Volume should be adjusted to be comfortably audible without excessive clipping The red clipping LED indicator located on the front baffle will light when the amplifier is within 3dB of clipping It is acceptable if the red LED lights occasionally If the red LED lights more than occasionally you should turn down the volume to avoid audible dist
4. or other devices including amplifiers that produce heat The product should be connected to a power supply only of the type described in the operating instructions or as marked on the product Replace the fuse only with one of the specified type size and correct rating The power supply cord should 1 be undamaged 2 never share an outlet or extension cord with other devices so that the outlet s or extension cord s power rating is exceeded and 3 never be left plugged into the outlet when not being used for a long period of time Care should be taken so that objects do not fall into and liquids are not spilled through the enclosure s openings The product should be serviced by qualified service personnel if A The power supply cord or the plug has been damaged B Objects have fallen into or liquid has been spilled onto the product C The product has been exposed to rain D The product does not appear to operate normally or exhibits a marked change in performance E The product has been dropped or the enclosure damaged Do not attempt to service the product beyond what is described in the user maintenance instructions All other servicing should be referred to qualified service personnel PANEL CONTROLS AND CONNECTIONS 1 INPUTS The electronically balanced XLR MIC input is designed to accept signals from any balanced or unbalanced low impedance Low Z microphone This qr input can also be used for low line
5. sounding mix Cutting the HIGH and BASS then pushing up the Volume control is equivalent to a mid range boost PANEL CONTROLS AND CONNECTIONS Note the PM 200A internal speaker has been specially designed to reduce feedback frequencies while allowing maximum punch from center vocal and instrument tones This allows clear and comprehensive monitoring with the speaker in close proximity with maximum feedback rejection The speakers are not meant to be flat in audio quality or used for music reproduction But when the band or DJ is pumping they kick out exactly what you need and then some 5 EXTERNAL SPEAKERS The PM 200A can also be used to power external speakers for additional EXTERNAL SPEAKERS monitoring or added volume Each External Speaker jack can power any number of speakers with a total impedance not being less than 80 The PM 200A actually uses a dual power amp each side of which is used to power the internal 80 speakers The power amp is capable of MIN IMPEDANCE 80 delivering up to 50W RMS of clean power to EACH SPEAKER When additional speakers are connected to the two External Speaker B O outputs they are automatically wired in parallel with each internal speaker reducing the total impedance of each channel If an 80 speaker MIN IMPEDANCE 80 is connected to each output the power amp can deliver up to 75W RMS to each channel that means 37 5W per speaker If the internal speakers are turned off in this configur
6. 1 UT FS ae OWNER S MANUAL PM 200A N UJ LOT CGC gt Congratulations you have purchased one of the finest personal stage monitors on the market today This unit was developed using the expertise of professional sound engineers and working musicians You will find that your new NADY AUDIO Powered Personal Stage Monitor has superior performance and greater flexibility than any other monitors in its price range The PM 200A Powered Personal Stage Monitor is the perfect tool for monitoring audio on stage or in rehearsal This unit puts the controls at your fingertips so you ll never have to scream for More Monitors again The speaker system is tailor made to reduce fee back while allowing vocals and instruments to stand out in the mix Simply input a line level feed from the main or monitor mixer and adjust the EQ s and Volume to your personal liking Or you can input your instrument vocal signal directly before outputting to the main PA to hear yourself solo With added features like Headphone outputs Line outputs and External Speaker outputs there are any number of PM 200A configurations to suit your special needs You ll hear yourself loud and clear and never miss the bridge again with the PM 200A by your side Please read this manual carefully to get the most out of your new unit Thanks for selecting Nady Audio as your choice in personal stage monitors TABLE OF CONTENTS FEATURES Designed to r
7. 2411 Fax 510 652 5075 www nady com
8. ation each 8Q external speaker can receive up to 50W RMS of power 6 INTERNAL SPEAKERS ENABLE When external speakers or headphones are being used it may be desirable to turn off the internal speakers to decrease noise or to increase the power somewhat to the external speakers When the External Speakers push button switch is depressed the internal speakers are enabled When it is out the internal speakers are disconnected INT SPEAKERS 7 HEADPHONES A The Headphone 1 4 stereo output can be used to monitor the signal post o Volume and EQ Itis capable of powering headphones with impedances of 80 or greater The internal speakers can be used simultaneously or turned off using the Internal Speakers Enable switch 8 POWER This switch turns the AC power on and off as indicated by the front baffle green Power Led 9 POWER CONNECTOR The IEC jack is used to connect the power cord to the AC Power Source Caution Never remove the center grounding pin as this can cause a serious safety hazard and will immediately void your warranty 12 9 10 230V BA 115V 6A Emenylio CA USA Mode in China SERIAL NO E See WARNING Rear panel heat sink can get very hot during hi power 115V 60Hz 230V 50Hz a operation Make sure to lea uci 4 PANEL CONTROLS AND CONNECTIONS 10 FUSE COMPARTMENT Replace with only the same type fuse If the fuse blows continuously have the unit serviced by qualified personne
9. ch may be of sufficient magnitude to constitute a risk of electric shock CAUTION DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL An equilateral triangle enclosing an exclamation point is intended to alert the user to the presence of important operating and service instructions in the literature enclosed with this unit A A IMPORTANT SAFETY INSTRUCTIONS When using this electronic device basic precautions should always be taken including the following LE 2 10 11 Read all instructions before using the product Do not use this product near water e g near a bathtub washbowl kitchen sink in a wet basement or near a swimming pool etc This product should be used only with a cart or stand that will keep it level and stable and prevent wobbling This product in combination with headphones or speakers may be capable of producing sound levels that could cause permanent hearing loss Do not operate for a long period of time at a high volume level or at a level that is uncomfortable If you experience any hearing loss or ringing in the ears you should consult an audiologist The product should be positioned so that proper ventilation is maintained The product should be located away from heat sources such as radiators heat vents
10. educe stage clutter and volume by putting the sound where you can most use it the compact rugged lightweight PM 200A can be mounted on a mic stand with optional mic stand mount adapter if needed set on a keyboard amp or table for effective up close monitoring or as a stage monitor with 4 different angled positions for optimum placement and versatility Powerful internal 150W RMS amp can power internal speakers plus up to four PM 100 Personal Stage Monitors using the two External Speaker outputs Specially designed dual ferro fluid 5 drivers offer superior gain and optimum intelligibility at key vocal instrument frequencies with ultimate feedback rejection Maximum 125dB maximum SPL cuts through even the loudest ambient noise clutter Balanced 1 4 TRS and XLR input jacks can be used simultaneously if desired Volume control 3 band EQ controls High Mid Bass front baffle Power On and Clipping LED indicators High powered Headphone Output and convenient 1 4 balanced Line Output for daisy chaining with other PM 200A or connecting to mixers and PA s Amplifier s integrated low noise distortion Mosfet outputs offer thermal short circuit and antithump on off protection Externally selectable 115VAC or 230VAC operation 2 An equilateral triangle enclosing a lightning flash arrowhead symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure whi
11. l The PM 200A powered mixer uses 20mm glass tube Fast Blow fuses 6A 250V for 115VAC 3A 250V for 230VAC 11 AC VOLTAGE SELECTOR SWITCH Before plugging in the power cord check to see that the unit is set for the proper voltage for your area 115V 60Hz or 230V 50Hz 12 HEAT SINK The heat sink can get very hot during high power operation Make sure to leave properly ventilated and avoid touching 13 MOUNTING SOCKET On the bottom panel of the PM 200A is a 5 8 dia socket for mounting the PM 200A on a mic stand Depending on your mic stand you may require the optional MSA 100 200A Mic Stand Adapter for most secure mounting For ordering see PM 100 200A Optional Accessories Ordering Form included PM 200A bottom and standard mounting socket MSA 100 200A Mic Stand Adapter SPECIFICATIONS Mic Input Input Impedance Maximum Input balanced XLR 2KQ 10 2dBm 235mV Sensitivity for max output w Volume max Line Input Input Impedance Maximum Input 40dBm 7 5mV balanced unbalanced TRS 1 4 20KQO 10KQ unbalanced 22dBm 10V Sensitivity for max output w Volume max Line Output Output Impedance Maximum Output w 10K load EQ and Volume High Mid Bass Headphone Output Power Power Amp Output Power 10dBm 230mV balanced XLR 1 4KQ 15 5dBm 4 3V rotary knobs 12dB 10K Hz 12dB O 2 5K Hz 12dB 120 Hz 1 4 TRS Stereo 2 x 80mW O 320
12. le implied warranties including warranties of merchantability and fitness are hereby limited to one year from the date of purchase Consequential or incidental damages resulting from a breach of any applicable express or implied warranties are hereby excluded This warranty is in lieu of all other agreements and warranties general or special express or implied and no representative or person including a Nady dealer agent or employee is authorized to assume for us any other liability in connection with the sale or use of this Nady Systems product Whereas some states do not allow limitations on how long implied warranties last and do not allow exclusion of incidental or consequential damages the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which may vary from state to state This warranty is subject to the following conditions 1 This system must have been purchased from an authorized Nady dealer and all warranty service must be performed by Nady s service department Any service not performed by Nady will automatically void this warranty 2 Items not covered physical damage resulting from improper handling of the unit in transit from the factory by the shipper Nady Systems is not responsible for such damage and all such claims must be made against the shipping company by the consignee defects caused by normal wear of the product expendable par
13. ortion and possible damage to the speakers or amplifier The PM 200A uses a high power amplifier in a small enclosure for maximum power and portability combined Care should be taken to avoid overheating and possibly damaging the power amp or speakers with excessive clipping Note Speakers and amplifiers damaged due to hard clipping are not covered under warranty 4 EQ The three band equalizer section utilizes a HIGH MID and BASS EQ control each of which has 12dB of cut and boost with a center detent for off indication The frequency response is flat when all three EQ knobs are in the center detent position The HIGH and BASS shelving controls have their frequencies fixed at 10 KHz and 120Hz respectively The MID control has a peaking response at 2 5KHz The EQ is a valuable feature of the PM 200A as it allows the user to control the tonal characteristics of their monitor mix For example boosting the BASS can fatten the sound add warmth to vocals or extra punch to bass drums and synths the MID control can be used to define the midrange or bring out the vocals and adjusting the HIGH control can provide a crisp sounding high end for high hat and vocal clarity Another very important yet often overlooked technique is to use the EQ to subtract from the mix Cutting the HIGH control can reduce unwanted sibilance hiss cymbals or high frequency feedback while attenuating the MID or BASS can also eliminate feedback or clear up a muddy
14. ts are typically connectors cables potentiometers switches and similar components damage or defects caused by abuse neglect accident failure to connect or operate the unit in any way that does not comply with applicable technical or safety regulations or improper repair excessive heat or humidity alteration or unreasonable use of the unit causing cracks broken cases housings or parts damage caused by leaking batteries finish or appearance items items damaged in shipment en route to Nady Systems Inc for repair The warranty is null and void if any Nady serial number has been removed or defaced How To Obtain Service 1 If factory service is required you must contact our Service Department at 510 652 2411 for a return authorization RA number Make sure the RA number is clearly marked on the outside of your package Please note if an RA number is not included our shipping department cannot accept your package 2 Send the unit back to Nady Systems 6701 Shellmound Street Emeryville CA 94608 freight pre paid You must include proof of date and place of purchase i e photocopy of your bill of sale or Nady cannot be responsible for repair or replacement Nady Systems Inc will not repair nor be held responsible for any units returned without proper identification return address and RA number clearly marked on the package 3 Per the above Nady will perform all warranty service and return the unit to you at no charge
Download Pdf Manuals
Related Search