Home

CM6300 - Compustar

1. Page 20 www tirstechonline com www compustar com F RSTECH LLC Alarm System CM6300 Install Guide Troubleshooting CM6300 Alarm LED Diagnostics When the alarm is triggered the LED on the RPS if installed Secure Valet if installed and the LED if in stalled will flash a certain amount of times as shown in the table below This is intended for users with 1 Way remotes Priority Trigger 1 LED Flash Diagnostic _ Door Hood Trunk Ign Triggered 2 flashes break then repeat 2nd Shock Triggered 3 flashes break then repeat 2nd Auxiliary Input Triggered 4 flashes break then repeat 5 flashes break then repeat Frequently Asked Questions CM6300 I have everything hooked up and the system will not respond A The remotes need to be programmed Review the Common Procedure section of this manual I am trying to program the control module with the OP500 Option Programmer and it flashes ER 01 when I plug it in to the antenna cable What should I do A Make sure that the system is not locked armed The last thing to check is the antenna cable or antenna extension cable make sure this is not damaged If you need to try another cable When the OP500 is working properly it will read success good You no longer need to program the remotes before the OP500 will sync I need a ground when armed wire does the control module have one A You can use the ground when armed wire on CN3 t
2. Wid prduj deo pesos 6u010 T 9 20d mdo gen vugezt SuUI uNCIg padul asuas Aay mem SW Od z ue HNDJeQ WWOSZI WAPOA pdu 96614 1000 yoojg apym v DOA vie Hnojag ywogz FONHA pdu 15611 wm Veaie 90d 7 vie unoaa YWOSZ Swang WOR du sg 1004 3 Geo ve VppuO ywoszi lu upug oug igsug eya ueeg 1 90d Dr L t buoy puz ywoszi SOEupiebupagn Out Jepujwey Wf DUIOd Wi 29upIS OF INGINO wwoSz awy WIDE Su SOC DUUSJUD YOG SLN you Og an SINYNY 20 POS OUUB UD UGS SUL IT HIT 031 HUM COCONND JUI UI Datop JOU S SIWO IRL s10ep 20 ejnpow epp ey 104 jonuow VIE Gy GOs GEO S d a SHUM JOSUaS YOOUS cy apua Alayog dng Wow punog Se Josuas Guoudo ee SS 2 ag OLUM lee x29019 DEn punog 3066 juo su EDU EH uaaa T UOMIUEy oi AZL Agu i peu SYUNIUBEID mr rteere OASE wom aid awia pox Ip AC RSTECH LLCE CM6300 Install Guide g CG O D 2 2 N CH N re D Ve gt amp O WW ai www tirstechonline com www compustar com F RSTECH LLC Alarm System CM6300 Install Guide Copyright 2012 Firstech LLC Page 4 Introduction CM6300 Thank you for purchasing this Firstech system for your vehicle The following installation manual is in tended for experienced and authorized Firstech technicians We
3. gi 3 15 3 16 4 01 4 02 4 03 4 04 4 05 4 06 Copyright 2012 Firstech LLC Page 25 RSTECH LLC oie ae www tirstecnoniine com www compustar com CM6300 Install Guide Auxiliary settings The Auxiliary settings adds five additional independent auxiliary outputs for a total of seven with this option turned on Special Option Group 1 allows for independent timing of these outputs Soft Disarm When a vehicle has factory security and the Firstech alarm is triggered you may have both alarms sounding at the same time In the default setting silencing the Firstech system will not shut down the factory system therefore requiring the user to first silence the Firstech system by tap ping unlock 1 time and then unlock a 2nd time to silence the factory system Option2 will send the Factory Alarm Disarm orange white wire CN3 or any other POC programmed as FAD and 5 seconds later sends rearm pulse orange wire CN3 to ensure the doors re lock if needed RPS This option changes the between the option RPS 2 or the new RPS Touch Please see the Placement and Use of Components section of this manual for details Aux 1 Output This feature determines the duration of the auxiliary 1 output Option 4 allows the output duration to be set for a specitic length of time 1 99 sec only available when using the OP500 Aux 2 Output This Feature determines the duration of the auxiliary 2 output Option 4 allows the outpu
4. 15 Trunk Output Timing This option changes the time of the output pulse on the violet white wire during trunk release The default setting is 1 second With the options you can extend the output by 2 3 or 4 seconds to a maximum of 4 seconds Copyright 2012 Firstech LLC Page 23 lessen Alarm System www tirstechonline com www compustar com CM6300 Install Guide 3 02 Confirmation chirps This feature will allow the user to select a shorter siren output time to simulate a quieter arm disarm start output 3 03 Dome Light Delay This option is used when connecting the door trigger input to the vehicles dome light circuit It delays the door trigger input to prevent the door open icon displaying on 2 Way remotes upon lock arm 3 04 Starter Kill This option determines the mode of the anti grind starter kill relay Default 1 Anti grind starter kill Option 2 Anti grind only no starter kill Option 3 Anti grind passive starter kill starter kill activates in 45 seconds after ignition is turned off 3 05 Anti Jacking This option requires the starter kill relay to be wired to the ignition vs the starter wire Default 1 Acts like starter kill removes power from the ignition which allows the car to crank but not start Option 2 Turns on anti jacking when the remote panics the system power from the ignition will be removed at the end of the 30 second siren duration thereby disabling the vehicle IMPORTANT
5. 50 seconds 3 times and flash the battery indicator on the remote When you query the remote or unlock disarm the system the remote will display the voltage of the vehicle s battery Options 3 and 4 are not available with CM6300 Copyright 2012 Firstech LLC Page 26 lessen Alarm System www tirstechonline com www compustar com CM6300 Install Guide Special Option Groups 1 amp 2 CM6300 IMPORTANT The OP500 is required to change settings in Special Option Groups 1 and 2 Special Option Group 1 2 Aux 1 Output Timing Option 4 01 must first be set to setting 4 This special option allows a specific output duration for Aux 1 to be programmed 3 Aux 2 Output Timing Option 4 02 must first be set to setting 4 This special option allows a specitic output duration for Aux 2 to be programmed 4 8 Aux 3 7 Output Timing Option 3 11 must first be set to setting 2 and the optional Auxiliary settings module must be used These special options allow specific output durations to be set for Aux 3 7 Only available with 2 Way LCD remotes Special Option Group 2 This special option group allows you to determine the output type of the POC wires on CN2 For example it you want to set POC 5 default setting status out to Aux 1 you will need change special option 5 to number 10 This must be done with the OP500 Option Programming CM6300 Option Programming Using the OP500 programmer The OP500 can be used to progr
6. When using ignition kill on manual transmission vehicles Option 2 will need to be utilized Option 2 disables the anti grind circuit while the vehicle is remote started if the anti grind circuit is active and the start kill relay is installed in the ignition the relay will buzz while remote started 3 06 Factory Alarm Option This feature is default to on when set to option 2 the security features of the CM6300 will be deactivated leaving the keyless features functional 3 07 Siren Duration Upon Alarm Trigger This option changes the time that the siren sounds during alarm trigger The available options are 30 60 and 120 seconds It will also sound chirps for 20 seconds as a fourth option 3 08 Horn Output This feature will change the behavior of horn output white wire POC8 CN3 3 09 Siren Output This Feature will change the behavior of the siren output brown wire CN3 3 10 Valet This option changes valet modes Default 1 Key on off five times or remote valet I Ill for 0 5 seconds with key in the on position Option 2 Key on off five times or remote valet Ill for 0 5 seconds key does not need to be in the on position Option 3 Secure valet RPS Valet or remote valet I IlIl for 0 5 seconds this option prevents the system from being put into valet via key on off five times To set up the RPS Valet feature review the Placement and Use of Components section Copyright 2012 Firstech LLC Page 24
7. buttons 2 3 Trunk and Key Start buttons on 2W901R SS simultaneously for 2 5 seconds The remote will beep once and the LCD or read REMOTE MENU indicating that you have entered programming mode STEP 2 Scroll through the remote options by taping button 3 or 4 Function button 2W901R SS Once the LCD RPS icon flashes reads RPS ON tap button 1 or Lock button 2W901R SS to turn this feature on The LCD will read RPS OFF STEP 3 Exit remote programming by holding down buttons 2 3 Trunk and Key Start 2W901R SS buttons simultaneously for 2 5 seconds The remote will beep indicating that you have successfully exited programming RPS Remote Paging Sensor Unlock Disarm RPS and car call functions do not require programming however in order to unlock disarm your vehicle you must program a 4 digit passcode numbers 1 through 10 only using the instructions below STEP 1 Disarm unlock the alarm remote must be programmed first and choose a 4 digit code You can not have zeros STEP 2 Turn ignition key to the on position and leave the driver s door open STEP 3 Knock on the windshield in front of the RPS a total of 5 times each time you knock the LED on the RPS will flash RED The LED will begin to flash rapidly in BLUE with successful completion of this step STEP 4 Enter the first digit of the desired four digit pass code by knocking on the windshield in front of the RPS the desired number of times For exampl
8. connector one CN1 In the default position it provides a positive parking light output To change to a positive trunk output move the jumper A negative parking light output is found on connector three CN3 and a negative trunk output is found on connector four CN4 Setting Auxiliary Outputs on Connector 4 You Must Have the OP500 Option Programmer For your convenience certain wires are defaulted to Auxiliaries However to set specific auxiliary outputs on the control module you must choose two odd pin wires on the black 18 pin connector that you are not using For example we will use POC 8 and 9 STEP 1 Plug in OP500 and use the Right or Left Arrow Button to scroll through the menu to POC 8 and POC 9 on LCD Line 1 STEP 2 Use the Up or Down Arrow Button to change the lower number on LCD Line 2 to 10 Auxiliary 1 or 11 Auxiliary 2 STEP 3 Scroll up the menu to Option 4 01 and 4 02 and set the options Please see the Option Table for details www tirstechonline com www compustar com F RSTECH LLC Alarm System CM6300 Install Guide STEP 4 The control modules have a secure auxiliary option 4 05 This requires you to tap button 4 before you tap button 2 for Aux 1 or button 3 for Aux 2 On 1 Way remotes you must hold the Trunk and Key Start buttons for 2 5 seconds then tap the Trunk button for Aux 1 or the Key Start button for Aux 2 STEP 5 If you need to change the time settings of the outputs go to AU or
9. ANT RFID STEP 5 Connect your antenna to the ANT RFID This is the blue 6 Pin port If you have a 4 Pin antenna cable use the included 4 Pin to 6 Pin adapter STEP 6 Find a spot to mount your ANT RFID on the windshield This is recommended for optimum range For more specific mounting location information visit us at www firstechonline com under the Authorized Tech section document titled FT EZGO Recommended Mounting Locations STEP 7 Program your EZ100 R and additional RF Kit remotes to the control module Maximum 3 Remotes including EZ100 R You are now ready to test your FT EZGO system Testing The FT EZGO STEP 1 Turn the auto unlock feature by holding the button on the EZ100 R for at least 8 seconds You will get one parking light flash and or siren chirp Hold the button again for at least 8 seconds and you will get two parking light flashes and or chirps showing that the auto unlock feature is off STEP 2 Arm Lock the vehicle and wait at least 15 seconds STEP 3 Walk up to the vehicle and it will automatically unlock disarm If you have the option set walk away and the vehicle will lock and arm Copyright 2012 Firstech LLC Page 9 www tirstechonline com www compustar com E RSTECH LLC Alarm System CM6300 Install Guide A Copyright 2012 Firstech LLC Page 12 Thermister Temperature Sensor Every 2 Way LCD Firstech RF kit includes an optional thermister which must be plugged into the 2 pin
10. AU2 on the OP500 LCD Line 2 is the timed output STEP 6 Hold the W Write button for 3 seconds to set all the options Version Diagnostics All the new control modules come with the ability to check which firmware is on the module This is accomplished by turning the ignition on Then with 2 Way remotes you must hold buttons 1 and 4 together for 2 5 seconds With the 1 Way remotes you must hold the Lock and Key Start buttons together for 2 5 seconds Blade Cartridge Slot and Connector The slot gives you the ability to use the Blade AL and Blade TB modules from Firstech and ADS With these modules you can virtually eliminate all wire connections between your control module and bypass module You only need to connect the main ignition harness and your required wires on the 20 pin Blade connector For more information on how to program and wire the Blade please visit www idatalink com for the specific wiring diagram for that vehicle The CM6 Series Blade connector has a locking tab Older blade harnesses will work but you must cut the notches on the black harness plug off Blade system includes 1 Blade AL or Blade TB NOTE These modules are blank and must be flashed on your computer 2 20 Pin locking wiring harness 3 3 Pin harness used in some installs IMPORTANT Install diagrams are not included and must be downloaded from www idatalink com compustar When flashing the Blade you can use the Y Cable OP500 end and not CM4 Series en
11. Fjestecueoe CM6300 Alarm System Installation Manual Firstech LLC 21903 68th Ave S Kent WA 98032 Phone 888 820 3690 Fax 206 957 3330 Please visit www firstechonline com for additional installation resources i Version 7 11 www tirstechonline com www compustar com F RSTECH LLC Alarm System CM6300 Install Guide Table of Contents CM6300 Introduction 4 Kit Contents 4 Installation Basics 5 Remote Programming Routine 6 Placement and Use of Components 6 Common Procedures 12 Wiring Descriptions 13 Option Programming Tables 20 Option Menu Descriptions 22 Special Option Groups 1 amp 2 27 Option Programming 27 Troubleshooting 31 Frequently Asked Questions 31 Technical Support Contacts 32 Copyright 2012 Firstech LLC Page 2 tem Alarm Sy ong poun usam punog toral A Ap out gi A 180854 punoo le WT Br zs Jere sof SH a at w n tr LOWE no E O U 8 LO Q E O Z E O H oO ES O Be U Ki 2 z SSES SUON DOP E a xoana Dono ve eu er Lawn 49018 ang pano woun vuos LI YOOIQEUDIO HANO yDOjUN Aoud YUIDGZ SINNA NANO gepaak YUN YUIDSZ uoN Ml anpop 4207 200g ovum dpjanpow ouuajuy anig Ty F Us vam o mo ACL Loi 481014 6 230d L xfv vunect 42010 4019 pdu ulj POOH A 8 90d WOH ywosz Le S D01 Waa indui Dupues YO SOUS 04 wiond ywosd
12. a e aia SE EE 3 02 Contirmation Chirps Medium 30 ms Short 15 ms Normal 60 ms ras 3 03 Dome Light Delay See D SC Auto kill Auto kill der Gelb Starter kill lanition Kill Auto door locks Off Auto door locks On g No Anti Grind g International Remotes w International Remotes w AUTO Function Only AUTO Function eT 3 06 Factory Alarm Option On OR 3 07 Siren Duration 30 sec 60 sec 120 sec Chirps for 20 seconds Upon Alarm Trigger Copyright 2012 Firstech LLC Page 20 lee zeecnax e one ae www tirstecnoniine com www compustar com CM6300 Install Guide Option Group 3 Continued Default Setting I Optional Setting Optional Setting Optional Setting OI IH IV Horn Output On Double Lock Only On Lock and Unlock On Lock Unlock and On Double Lock and Start Start Siren Output On Tock Unlock and On Double Lock Only On Lock and Unlock On Pouple Lyck ang Start Start pret SLU Key 5 times or Remote Secure Valet Valet Remote I ll while y SE EU Detault code 3 3 Ignition is On Auxiliary Settings Mode Disabled Enabled Po E a of On a RPS 2 RPS Touch ___ Option Group 4 Feature O Default Setting I Optional Setting EE E ene rogram rogram ll rm Aux 2 output Control rm Secure Aux Output Auxiliary Input 1 Green CN Auxiliary Input 2 Green CN Extended Accessory After Ign Until Door Open 1 Disable Arm Disarm A when Brown White Key Sense or Glow Plug input Glow Plug In
13. am any available option It is required to program options in Special Option Groups 1 and 2 STEP 1 Make sure system is unlocked disarmed Using the blue or black 6 pin connector on the top of the OP500 connect it to the control module via the antenna wire Use the included extension cable if necessary Once connected the OP500 will power up as long as the main ignition harness to the controller has been connected properly STEP 2 To change the option number you wish to program use the left and right arrow keys on the OP500 It will scroll through the options available in menu 1 and then move to menu 2 then 3 and 4 Use the up and down arrow buttons on the OP500 to adjust the option settings 1 is the default setting and 2 3 and 4 are the optional settings Copyright 2012 Firstech LLC KISEKR lessen Alarm System www tirstechonline com www compustar com CM6300 Install Guide At the end of menu 4 if diesel mode or auxiliary setting functions were enabled or if any of the auxiliary outputs were set to Program the duration of these settings can now be adjusted Following the auxiliary and diesel settings if selected the POC options will be displayed on the OP500 The POCs can be set between O default and 19 All are only available on the CM5000 STEP 3 When finished with the adjustment of the various option settings press and hold the W write button until the OP500 chirps w
14. as been disarmed and the doors have not been opened 1 11 Ignition Accessory Upon Unlock Negative Out This option will pulse the ignition wire accessory or both upon unlock disarm Most new Chrysler vehicles need the ignition and accessory pulsed to disarm the factory alarm 1 13 Double pulse disarm This feature changes the behavior of the small orange white disarm wire When the feature is turned on it will change the default single pulse to double pulse upon disarm unlock 1 14 Auto Mode EZ GO This feature enables the RFID EZ GO functions according to the option selected Once selected and the EZ GO remote has been programmed to the Control Module the user can activate deactivate the proximity function by holding the button on the back of the RFID remote for 10 seconds Option 2 will keep the EZ GO antenna awake and allow the system to unlock every time the RFID remote is within proximity of the EZ GO antenna regardless of the state of the control module i e locked armed or unlocked disarmed Option 3 will allow the RFID remote to proximity unlock the system after it has been outside proximity of the EZ GO antenna and the control Module has been locked armed for at least 15 seconds Option 4 will allow the system to arm lock aprox 12 seconds after the RFID remote leaves proximity of the EZ GO antenna and allow it to unlock the system as the user approaches the vehicle and is within the proximity of the EZ GO antenna 1
15. ch antennas are calibrated for horizontal installation at the top of the windshield The cable that connects the antenna to the control module must be free from any pinches or kinks Installing the antenna in areas other than the windshield may adversely affect the effective transmitting distance of the remotes Copyright 2012 Firstech LLC Page 6 www tirstechonline com www compustar com E RSTECH LLC Alarm System CM6300 Install Guide Placement and Use of Components CM6300 RPS Touch and RPS Remote Paging Sensor The RPS is an optional feature The car call RPS feature uses a small sensor that is mounted on the inside of your windshield Important When using the RPS Touch you cannot use the LED port or Secure Valet Switch RPS Touch Remote Paging Sensor The new RPS touch has multiple features including remote paging 4 digit pin unlock disarm and arm lock All features are operated with a simple touch of the sensor Please program Option 3 16 to Setting 2 RPS Touch and car call functions do not require programming however in order to unlock disarm your vehicle you must program a 4 digit passcode numbers 1 through 10 only using the instructions below STEP 1 Choose your RPS Touch 4 digit code O is not available STEP 2 Turn ignition to the ON position and leave driver s door open STEP 3 Hold your finger over the Red Circle icon for 2 5 seconds STEP 4 When the siren chirps and LEDs fla
16. ck doors and arm alarm IMPORTANT You must reverse polarity for trigger door lock systems For additional lock settings review Option Group 1 Pin 6 Not used Connector 6 CN6 4 Pin RS 232 Data Port This connector is used for updating control modules via www compustar com You must also use this port to flash Blade bypass modules This port provides simple connectivity of Fortin and iDataLink bypass modules This port is also used to communicate with DroneMobile controllers Make sure to use the data port from the DroneMobile unit to this RS232 port Copyright 2012 Firstech LLC Page 17 www tirstechonline com www compustar com E RSTECH LLC Alarm System CM6300 Install Guide Connector 7 CN7 4 Pin to 4 Pin or 6 Pin Pre wired Antenna Cable Connect your antenna cable to this port You can only use 4 to 4 pin or 4 to 6 pin antenna cables 6 to 6 Pin antenna cables do not work Do not use both Connector 7 and Connector 8 at the same time Pin 1 Yellow RX input This wire receives the signal from remote Pin 2 White TX output This wire transmits the signal to remote Pin 3 Red Constant 12V positive output Pin A Black Negative ground Connector 8 CN8 6 Pin to 6 Pin Pre wired Antenna Cable Connect your antenna cable to this port You can only use 6 to 6 pin antenna cables 4 to 4 or 4 to 6 Pin antenna cables do not work Do not use both Connector 9 and Connector 10 at the same time Co
17. cks setting 2 which will let the doors lock when brake is pressed Pin 7 Green POC 3 Auxiliary 4 250mA negative output This is an optional output that will provide a programmable output to trigger sliding doors power windows or whatever other features vou d like Pin 8 Violet Black Trunk negative input This is an optional input that will monitor when the vehicle s trunk has been opened The proper wire will provide a trigger while the trunk is open Pin 9 White Black POC 4 Auxiliary 3 250mA negative output This is an optional output that will provide a programmable output to trigger sliding doors power windows or whatever other features you d like Pin 10 Red White Door trigger input This wire monitors negative or positive trigger door pins The proper wire will provide a trigger or a trigger only when the doors are opened You will need to test the wire for proper polarity and set door dip switch on the control module for the corresponding polarity Copyright 2012 Firstech LLC Page 15 lessen Alarm System www tirstechonline com www compustar com CM6300 Install Guide Pin 11 Black POC 5 Auxiliary 2 250mA negative output This is an optional output that will provide a programmable output to trigger sliding doors power windows or whatever other features vou d like Pin 12 Brown White This wire looks for key sense negative input The proper wire will show a
18. ct to the RS232 before the CM is powered up the this feature will automatically switch to option 2 4 12 Impact Sensor This feature changes between the standard included shock sensor and the optional DAS Digital Adjustable Sensor The DAS has additional programming Please see the Placement and Use of Components section of this manual for details 4 13 Antenna Power Save Some people may not drive their vehicle very often this may cause the battery to become discharged because it is not getting recharged on a regular basis The antenna power save option will turn off the antenna after the specified amount of time to conserve power While the antenna is asleep the system will not respond to the remotes Any type of input to the system will wake up the antenna i e ignition brake door trunk hood shock RPS etc A remote start only user just needs to open their door to reactivate the system however a user with an alarm or alarm start system will need to trigger the pre warn stage of the shock sensor to quietly wake up the antenna This feature is not available when using EZ GO 4 14 Low Battery Warning This feature option which is default to off when the system is armed and the feature is on the main control unit will monitor the voltage of the vehicles battery at its connection point When the battery voltage drops to or below 11 3 volts the control module will send a page to the 2 Way It will beep several times for 5 seconds every
19. d ADS and Firstech recommends using the 4 pin RS232 cable to avoid contusion Cartridge must be removed to flash the control module firmware NOTE The ADS RNG C1 ADS RNG C2 and ADS RNG GM3 are not included and must be purchased separately The 20 pin Blade connector comes only with the Blade cartridge and not the CM6 control modules d WARNING Manufacturer or seller assumes no responsibility for any injuries and or damages caused by LA improper care of the product such as decomposition conversion and transform done by a user voluntarily WARNING There should be no wiring routed around any pedals which can cause a driving hazard Wiring Descriptions CM6300 lessen Alarm System www tirstechonline com www compustar com CM6300 Install Guide Connector 1 CN1 4 Pin Pin 1 Red Constant 12V positive power input This wire must be connected The proper vehicle wire will test 12V at all times while the key is in the off position the on position and during crank Pin 2 Green White This is a dual purpose wire that features selectable functionality thru the trunk light jumper on the control module It is either a positive parking light output or positive trunk output This wire carries a 10 amp fuse Default Parking light positive output The proper vehicle wire will test 12V when the parking light switch is in the on position Optional Trunk release positive output The proper vehicle
20. d 6 Pin antennas This will work with all new RF kits as well as the current ones Do not have antennas plugged into both ports on the CM6300 as the remotes will not function properly Supports Blade The CM6300 supports the Blade AL and TB systems as well as 2 way data for Idatalink and Fortin bypass modules The data port will also support full data connection with DroneMobile New Option Menus It is important to familiarize yourself with all the options as it will save time in most applications For in stance Option 1 04 controls the double pulse unlock feature on all CM6 series control modules Programmable Output Channel POC Must have Option Programmer OP500 All control modules come with 9 programmable outputs that can be configured 19 different ways It is important to familiarize yourself with the POCs as it will save time in most applications Note that the CM6300 POCs are defaulted to Aux 1 5 as shown in the Special Option Group Table 2 Internet updatable processors Visit www firstechonline com All CM6 series units are equipped with some of the most powerful processors available today This flexibility allows for on demand internet updating capabilities in the event of a version update or change All CM6 series control modules use the same version firmware lessen Alarm System www tirstechonline com www compustar com CM6300 Install Guide Remote Programming Routine CM6300 IMPORTANT Any and all remotes must be co
21. ded to the control module prior to performing any and all operations STEP 1 Activate programming mode by manually turning the vehicle s key between the Ign On and Off or the Acc amp On positions five times within 7 seconds The vehicle s parking lights will flash once with the suc cessful completion of this step Note this step also places the control module into Valet Mode STEP 2 Within a 2 second period after the 5th ignition cycle tap Button on two way remotes or the Lock button on one way remotes for 0 5 seconds The parking lights will flash once to confirm the transmitter has been coded Repeat for additional remotes up to three Exiting Programming Programming is a timed sequence After 2 seconds the parking lights will flash twice signaling the end of programming mode Programming Multiple Remotes After the confirmation flash given in STEP 2 code additional remotes by tapping Button on two way remotes or the Lock button on one way remotes The parking lights will flash once confirming each additional remote All systems can recognize up to three remotes Note If you do not program any remotes and enter this sequence it will put the system into Valet Mode Only the keyless entry will work in Valet Mode To exit Valet Mode just program remote s Placement and Use of Components CM6300 IMPORTANT The placement and use of components are critical to the performance of this system Antenna and Cable Firste
22. e to enter 3 knock on the sensor 3 times each time you knock the LED will flash RED then wait Copyright 2012 Firstech LLC Page 8 www tirstechonline com www compustar com E RSTECH LLC Alarm System CM6300 Install Guide Placement and Use of Components CM6300 STEP 5 The LED on the RPS will confirm your first number by flashing BLUE slowly Once the LED begins to flash rapidly in BLUE enter your second number by repeating step 4 STEP 6 Repeat steps 4 amp 5 to enter all four numbers STEP 7 Turn the ignition OFF the RPS disarm unlock passcode is now programmed Follow steps 3 5 to enter your disarm unlock code Alarm rearm and lock To rearm knock on your sensor 5 times Alarm disarm and unlock To disarm knock on your sensor 5 times Wait for the Blue LEDs to flash rapidly Follow STEP 4 and 5 above to enter your 4 digit passcode 2 Way LCD remote paging To page a 2 Way LCD remote just knock on the RPS twice Knock Panel Sensitivity To change knock sensitivity disarm the system and adjust the switch on the rear of the RPS The larger the circle the more sensitive the knock sensor is Secure Valet Switch Not available when using RPS Touch The optional Secure Valet Switch prevents the alarm from being put into valet mode through cycling the ignition on off five times The Secure Valet Switch is more secure than traditional toggle valet switches because it requires a two digit code To program
23. e the hood is open Pin 19 Violet POC 9 Auxiliary 1 250mA negative output This is an optional output that will provide a programmable output to trigger sliding doors power windows or whatever other features vou d like Pin 20 Brown Siren 12V positive output Connect this wire to the wire located on the siren To change siren output settings review Option 3 7 Copyright 2012 Firstech LLC Page 16 lessen Alarm System www tirstechonline com www compustar com CM6300 Install Guide Connector 5 CN5 6 Pin Pin 1 Not used Pin 2 Violet White Trunk release 250mA negative output This is an optional output that will release the trunk Use CN1 Pin 2 if the vehicle is equipped with a trunk release System will unlock doors and disarm alarm prior to trunk release Pin 3 Orange Black 2nd Unlock 250mA negative output This is an optional output that will provide a pulse for driver s priority door lock IMPORTANT You must isolate the driver s door and turn on Option 1 3 Pin A Blue Unlock 250mA negative output This is an optional output that will provide a pulse for unlocking doors System will unlock doors and disarm alarm IMPORTANT You must reverse polarity for trigger door lock systems For additional lock settings review Option Group 1 Pin 5 Blue Black Lock 250mA negative output This is an optional output that will provide a pulse for locking doors System will lo
24. e will allow the user to unlock the driver s door first and if the unlock button is pressed again within 4 seconds the other doors will unlock The driver s door unlock must be isolated from the other doors and use the blue unlock The Orange Black CN4 will be used for your 2nd Unlock output to unlock all other doors Copyright 2012 Firstech LLC Page 22 www tirstechonline com www compustar com F RSTECH LLC Alarm System CM6300 Install Guide 1 04 Double Pulse Unlock If enabled this option will cause the system to double pulse the lock unlock or both lock and unlock outputs This can be used for vehicles that need two pulses to unlock or relock the doors 1 07 Unlock Disarm with Trunk Release This option allows the user to configure or disable the unlock disarm outputs that trigger with the trunk release command 1 08 Passive Mode This option comes with default off This feature controls what the lock wire does during passive mode Passive must also be activated by the end user remote according to the process specitied in the remote user s manual 1 09 Ignition Controlled Locks Setting 2 will lock the doors when the ignition is turned on and doors closed Tach sensing mode must be used for setting 3 You must also turn this feature on through the remote by tapping I IV 2 Way remotes or Lock Key 1 Way remotes 1 10 Auto Relock This option will automatically relock rearm at the selected timed if system h
25. hat goes to the starter kill relay You must cut this wire and place a diode in line so that when the ignition on the other side of the relay goes to ground it won t back feed to your accessory Install the stripe side of the diode facing the control module On the brain how do I set the auxiliaries A Auxiliary 1 through 5 are defaulted on with the CM6300 Although you must have an Option Programmer OP500 to change the outputs to a specific time Secure auxiliary option 4 05 will prevent these outputs from triggering without doing query first Please review the Special Option Group programming section of this manual for more details The vehicle will lock and unlock but not flash the parking lights A The system is in valet mode Tap buttons I Ill for 0 5 second or Lock and Trunk Release buttons for a half second Whenever I try to arm the vehicle it chirps the siren 3 times and will not arm A Check the hood and trunk trigger inputs Copyright 2012 Firstech LLC Page 31 www tirstechonline com www compustar com E RSTECH LLC Alarm System CM6300 Install Guide Do the door locks flip flop in polarity A No You can use the CompuPack relay pack for high current positive locks or the DM600 harness used for low current 600mA positive locks What are Firmware Version Diagnostics A When you turn the Ignition on and hold buttons 1 and 4 or Lock and Key Start for 2 5 seconds then the parking ligh
26. hich is approximately 2 5 seconds This will write the settings to the control module Wait until the module displays Success before disconnecting it from the antenna cable To reset the options hold the R reset button and the W write button for 2 5 seconds Release then write the reset hold the W button until the OP500 chirps which is approximately 2 5 seconds Option Programming Using a Remote Using a remote is a timed process so read this section in its entirety before beginning IMPORTANT Special Option Groups cannot be programmed with a remote the OP500 must be used STEP 1 Select the option menu that contains the desired programming option To program options use the following button combinations How to Program Options with 5 Button 2 Way Remotes Scroll Through between each tap Select Option 1 Select Option 2 Select Option 3 GE fEE LEE EE moree Menu Wait for chirp With 2 Way Wait for chirp between each Remotes F Trunk for 2 5 seconds then F Trunk for 2 5 seconds F Trunk for 2 5 seconds Tao K then F Key for 2 5 apiisey Button seconds F Key for 2 5 seconds then F Trunk for 2 5 Tap Key Button seconds F Key for 2 5 seconds then F Key for 2 5 Tap Key Button seconds Copyright 2012 Firstech LLC Page 28 Tap Lock Tap Unlock Tap Trunk Tap Key Button Button Button Button Tap Lock Tap Unlock Tap Trunk Tap Key Button Button Button Bu
27. highly recommend that you contact your local Firstech dealer and seek professional installation Call 888 820 3690 or visit our websites at www compustar com or www firstechllc com to locate your nearest dealer If you need additional or replacement remotes and or online support please visit www compustar com dealersupport Caution The Manufacturer s warranty will be void if this product is installed by anyone other than an authorized Firstech dealer Firstech reserves installation support services to authorized dealers only This manual may change frequently Please check www compustar com dealersupport for updates Kit Contents CM6300 All Firstech FT 6300A CONT controllers include the following CM6300 main control module Wiring diagram sheet Main wiring harness Wiring harnesses Hood pin Mountable bright blue LED Firstech dual stage shock sensor RF Kits with remote s Antenna and Antenna Cable are not included with the FT 6300A CONT The following sensors are available but not included with every system Auto lock and unlock system FT EZGO Remote pager sensor FT RPS TOUCH or FT RPS 2 Firstech secure valet switch FT VALET GREY Thermister temperature sensor FT TEMP SENSOR 2 Way LCD remote systems only DAS sensor FT DAS The remote s and antenna are modular and are not specific to the control modules You have the ability to pair almost any Firstech remote s and antenna receiver t
28. ht flash and or siren chirp before selecting the option Tap Button 1 Tap Button 1 Tap Button 1 Tap Button 1 HAG SE Tap Button 2 Tap Button 3 Tap Button 4 Tap Button 2 Tap Button 3 Tap Button 4 Tap Button 2 Tap Button 3 Tap Button 4 Tap Button 2 Tap Button 3 Tap Button 4 HEHE HEHE FRE How To Program Options With 1 Way Remotes With 2 Way Wait for chirp between each Remotes Lock Unlock for 2 5 seconds then Lock Unlock for 2 5 seconds Lock Unlock for 2 5 seconds then Lock Key for 2 5 seconds Lock Key for 2 5 seconds then Lock Unlock for 2 5 seconds Lock Key for 2 5 seconds then Lock Key for 2 5 seconds Copyright 2012 Firstech LLC Scroll Through Menu between each Wait for chirp Hold Trunk Key for 2 5 seconds Hold Trunk Key for 2 5 seconds Hold Trunk Key for 2 5 seconds Hold Trunk Key for 2 5 seconds Wait for corresponding parking light flash and or siren chirp before selecting the option Select Option 1 Select Option 2 single Tap Lock Button Tap Lock Button Tap Lock Button Tap Lock Button Select Option 4 Hold Trunk Key for 2 5 seconds Hold Trunk Key for 2 5 seconds Hold Trunk Key for 2 5 seconds Hold Trunk Key for 2 5 seconds Tap Unlock Button Tap Key Button Tap Unlock Button Tap Key Button Tap Unlock Button Tap Key Button Tap Unlock Button Tap Key Button
29. impact sensitivity Firstech Shock Sensor For best results mount the shock sensor by zip tying it to the vehicles main ignition harness You can also use the supplied mounting hardware to mount your sensor There is a small dial on the sensor that ranges from Off to 10 The higher the number on the dial the greater sensitivity of impact A small adjustment to the dial can make a significant difference in sensitivity for both 1st and 2nd stages Recommended dial settings for most vehicles is somewhere between 2 amp 4 Siren To adjust duration time when the alarm has been triggered change Option 3 07 the system default is 30 seconds Copyright 2012 Firstech LLC Page 10 www tirstechonline com www compustar com E RSTECH LLC Alarm System CM6300 Install Guide FT EZGO Setup The FT EZGO from Firstech will unlock disarm the vehicle when in range It will also lock arm and unlock disarm the vehicle when you press the button on the EZ100 R Installing The FT EZGO STEP 1 Flash your CM6 Series control module for FT EZGO compatible firmware STEP 2 Set Option 1 14 to Setting 2 3 or 4 STEP 3 Connect included 6 Pin to 6 Pin with Ground Wire to control module If connecting to a 4 Pin to 4 Pin antenna use the included 6 Pin to 4 Pin adapter STEP 4 Connect the ground wire from the included 6 Pin to 6 Pin cable to vehicle s ground Warning Failure to connect this wire WILL result in damage to your FT EZGO antenna
30. ine com www compustar com CM6300 Install Guide Connector 3 CN3 20 Pin Blade Connector New Generation This connector is used only if you are installing a Blade AL or Blade TB The wiring harness for this connector also comes with the Blade cartridge Please refer to the Blade install guide for wire description The new generation 20 pin Blade connector now has a locking tab The old connector with out a locking tab is compatible but you must modify the connector Connector 4 CN4 20 Pin Programmable Output Connector POC IMPORTANT Odd Pin numbers 1 through 17 are programmable for up to 19 different output types Reter to Special Option Group 2 for complete details Pin 1 Blue 250mA negative output when armed and during remote start while running This wire has a connector and must plug into same wire at the starter kill relay Caution When this wire is being used to trigger aftermarket accessories it must be diode isolated Pin 2 Not Used Pin 3 Green White POC 1 Parking light 250mA negative output The proper wire will test when the parking light switch is in the on position Pin A Not Used Pin 5 Red Black POC 2 Auxiliary 5 250mA negative output This is an optional output that will provide a programmable output to trigger sliding doors power windows or whatever other features you d like Pin 6 Light Blue White Foot brake input This is used for option 1 09 Igniton controlled door lo
31. n STEP 3 Once finished scrolling through the menu wait for the parking lights and or siren chirp to contirm the option number i e option 2 04 will flash 4 times Then use one of the table selections to select the option corresponding to your desired setting Resetting to Factory Defaults To reset the options in a particular menu group enter the menu shown in the above tables To reset options with a 2 Way remote tap button 3 three times To reset options with a 1 Way remote tap the Key Start button 3 times Wait for the siren to chip and parking lights to flash between each tap After the third tap the option menu will reset and the siren will chirp three times This must be done for each option group that needs to be reset Copyright 2012 Firstech LLC Page 29 ai CM6300 Install Guide RSTECH LLCE Alarm System www tirstechonline com www compustar com How to Program Options with 2 Way Remotes with Roman Numerals With 2 Way Wait for chirp between each Remotes Option 1 2 for 2 5 seconds then Menu 1 1 2 for 2 5 seconds Option Menu 2 Option Menu 3 Option Menu 4 2 for 2 5 seconds then 4 for 2 5 seconds 4 for 2 5 seconds then 1 2 for 2 5 seconds 1 1 1 4 for 2 5 seconds then 1 4 for 2 5 seconds Scroll Through Menu between each Wait for chirp Tap Button 4 Tap Button 4 Tap Button 4 Tap Button 4 Wait for corresponding parking lig
32. nnector 9 CN9 2 Pin Pre wired Thermister Plug optional thermister into this connector to monitor the vehicle s temperature It is used to display temperature on two way LCD s To use Timer Start features review Option Group 2 IMPORTANT New Thermister plugs are blue 2 pin connectors on the CM6 series but old white plug Thermisters will still work Pin 1 Black Thermister Pin 2 Black White Thermister Connector 10 CN10 3 Pin Pre wired Valet Programming Switch Pin 1 Gray Black Negative Cl ground Pin 2 Gray 3V positive L E D output Pin 3 Gray Negative Cl output Copyright 2012 Firstech LLC Page 18 F RSTECH LLC Alarm System www tirstechonline com www compustar com CM6300 Install Guide Connector 11 CN11 2 Pin Pre wired LED Note Do not mistake for Thermister port Pin 1 Black L E D negative ground Pin 2 Black White L E D 3V positive output Connector 12 CN12 4 Pin Pre wired RPS Pin 1 Black Negative ground Pin 2 White Negative paging input Pin 3 Red 12V positive output Pin A Yellow 9V positive L E D output Connector 13 CN13 4 Pin Pre wired Shock Sensor or DAS Sensor Pin 1 Black Negative ground Pin 2 White 2nd stage negative input Instant trigger Pin 3 Red 12V positive output Pin 4 Yellow 1st stage negative input Warn away Connector 14 CN14 4 Pin Optional Sensor Input This connect
33. nstall Guide 4 07 Aux 2 Input This option changes the input behavior of the instant trigger wire on the Aux Input Sensor green connector Default 1 Will instant trigger with a negative ground input Option 2 Will pre warn with a negative ground input Option 3 Will arm the alarm with a negative ground input Used when adding an alarm to a factory keyless entry system Option 4 Changes the output into an open circuit input 4 08 Extended Accessory After Ignition Shutoff Negative Output This option keeps the Accessory wire powered up after the ignition is shut off This can be used to keep the radio turned on even after the key is removed from the ignition similar to GM vehicles 4 09 negative Key Sense Default setting sets the wire to off Option 2 changes the wire to a negative key sense input Keys sense input can keep system from passive arming while the key is still in the ignition Key sense also turns off dome light supervision when the key is inserted into the ignition Option 3 will provide an arm disarm disable input wire input polarity jumper selectable on the CM to work with analog arm lock disarm unlock input using green CN8 with CM6000 CM6300 using red CN6 with CM6200 4 11 Data to Data interface protocol through RS232 Port Default setting allows for compatibility with ADS Idatalink modules Option 2 changes compatibility to Fortin interface modules If a Fortin Module is conne
34. o the CM6300 This includes all 4 and 6 pin antennas Any questions on contents please contact your distributor or us directly at 1 888 820 3690 Monday through Friday 8 AM to 5 PM Pacific Time lessen Alarm System www tirstechonline com www compustar com CM6300 Install Guide L L Copyright 2012 Firstech LLC Page 5 Installation Basics CM6300 If you are new to installing Firstech Series Remote Starts and or Alarms we highly recommended that you thoroughly review this manual to installing your first unit Key Points to Consider Before Installation You must code remotes to this system before anything will function Program remotes by cycling the ignition ON OFF five times within seven seconds and tap button 1 half second on the first remote and then tap button 1 half second on the second remote RPS Touch Touch Remote Paging Sensor The optional RPS that has four main functions 1 Status LED 2 Remote notification when triggered 3 Auto unlock alarm disarm when a user specific 4 digit knock code is entered via tapping sensor through the windshield 4 You can also relock your vehicle if equipped with an RPS Touch sensor DAS Sensor The DAS sensor monitors forward movement for remote starting manual transmissions dual stage impact and auto adjusting tilt sensor See the DAS Sensor section of this manual for details Supports 4 Pin and 6 Pin Antennas The CM6300 supports both Firstech 4 Pin an
35. or provides optional sensor inputs Most commonly used with proximity and tilt sensors Pin Block Negative ground Pin 2 Black White 2nd stage negative input Instant trigger Arm Pin 3 Red 12V positive output Pin A Grey White 1st stage negative input Warn away Disarm Copyright 2012 Firstech LLC Page 19 www tirstechonline com www compustar com E RSTECH LLC Alarm System CM6300 Install Guide Option Programming Tables CM6300 Option Group 1 Default Setting Optional Setting Optional Setting Optional Setting 0 8 sec SR GE Disarm and Trunk Release Unlock Disarm With Trunk Release Factory Disarm Trunk Release Only Trunk Release Only Seele Of Passive Locking with No Passive Locking Passive Arming with Passive Arming RPM Locks Tach Ignition controlled door locks Sensing Modeni Auto Relock If a door is not opened within 60 sec this amount of time Ignition and Acc Pulse same timing as disarm pulse Ignition Accessory Out Ignition Pulse same Acc Pulse same tim Off e Upon Unlock Negative Out timing as disarm pulse ing as disarm pulse Double Pulse Disarm Output Single Pulse Double Pulse Aaa Mode FT EZGO Unlock for FT EZGO Unlock FT EZGO Lock and FTX Unlock Trunk Output Timing 2 sec 3 sec 4 sec Option Group 2 Not Available in CM6300 Option Group 3 o Feature Default Setting I saat
36. port of the control module for use This plug is blue on the CM6300 The use of the thermister allows the 2 Way remote to display the vehicle s interior temperature on the remote LCD liquid crystal display IMPORTANT New thermister plugs are blue 2 pin connectors on the CM series but old white plug thermistors will still work Hood Pin The hood pin switch triggers the alarm in the event the hood is opened while the system is armed Backup Battery The backup battery input on the control module brain is for any optional battery backup unit FT BATT BACKUP The red positive lead acts both as an input and charging output for a 12 Volt battery backup A backup battery maintains basic alarm functionality when main vehicle power is lost See the wiring schematic section for complete details Do not power any other modules or DroneMobile off this port as it will not support a heavy load of current Common Procedures CM6300 Jumper Settings Caution Jumper settings affect the polarity and use of certain outputs If these jumpers are used incorrectly damage to the vehicle and or control module may occur Jumper 1 Door Trigger Polarity Determines the polarity of the door trigger input wire red white In the default position the door trigger registers negative triggers To change to a positive trigger move the jumper Jumper 2 Parking Light to Trunk Output Determines the output type not polarity of the green white wire on
37. put Key Sense Input Wire moed Same Time Bypass Through 5232 Pon abs form OOO O a es Wer lst Stage Disarm Input Impact Sensor Shock Sensor DAS Sensor 2nd Stage Double g H Arm Input 2nd Stage Arm Input ol Aux output Cont enter 2 04 Suman esta E Copyright 2012 Firstech LLC Fjpsvecuece vies eri seei WWW tirstecnonline com www compustar com CM6300 Install Guide Special Option Group 1 Special Option Group 2 Setting and OP500 Value Programmable Output 0 Default Setting 1 18 Optional Settings Connector POC 1 2nd Parking Light Green White POC 2 Aux 5 Red Black 2nd Light 1 2nd Start 2 2nd IG1 3 FOC Ge be 2nd Acc 4 Status Out 5 Rearm Out 6 aay An Whi ok Disarm Out 7 Horn Out 8 Dome Light 9 POC 5 Aux 2 Black Aux 1 Out 10 Aux 2 Out 11 Aux 3 12 Le POC 6 Rearm Wire Orange POC 7 PB Mee Aux 4 Out 13 Aux 5 Out 14 Aux 6 Out 15 Le POC 8 Horn White Aux 7 Out 16 N A 17 GWA 18 EN POC 9 Aux 1 Violet Option Menu Descriptions CM6300 1 02 Door Lock Unlock Pulse Duration This feature determines the output duration of the door lock and unlock pulses Some vehicles do not respond to short door lock unlock pulses This does not affect the output of the factory arm orange wire CN3 or factory alarm disarm orange white wire CN3 1 03 Driver s Priority Unlock If enabled this featur
38. r explanation or switches STEP 3 Connect cable to the red 4 pin port on the CM6 Series module STEP 4 Mount DAS securely using zip ties or included hardware Can be mounted in any orientation Tilt will set 30 seconds after arming Switch 1 ON 3 Degree Tilt Switch 2 ON 4 Inch Movement OFF 1 5 Degree Tilt OFF 3 Inch Movement Adjusting DAS Shock Sensitivity CM6000 or CM6300 STEP 1 Turn the ignition to the on position STEP 2 2 Way remotes hold buttons 1 and 2 Lock and Unlock for 2 5 seconds You will get two parking light flashes 1 Way remotes hold Lock and Unlock for 2 5 seconds You will get two parking light flashes STEP 3 To set the Warn Away Zone 1 tap button 1 1 Way Lock After you get one parking light flash tap the vehicle You will get siren chirps 1 most sensitive through 10 least sensitive This sets the impact sensitivity of Warn Away Zone 1 Setting Zone 1 will automatically set Zone 2 If you would like to manually set Zone 2 proceed To set Instant Trigger Zone 2 tap button 2 1 Way Unlock After you get two parking light flashes tap the vehicle You will get siren chirps 1 most sensitive through 10 least sensitive This sets the impact sensitivity of Instant Trigger Zone 2 STEP 4 Once you get two parking light flashes you are ready to test your DAS Testing The DAS Sensor STEP 1 Turn the ignition off and Arm Lock the system STEP 2 Wait 30 seconds then test the
39. sh in a circular pattern tap on your first number Hold the number for 2 5 seconds to choose 6 through 10 After choosing your first number you will get one siren chirp and LEDs will flash in a circular pattern STEP 5 Repeat Step 4 until all four digits are set You will get 1 siren chirp and 1 parking light flash Repeat Steps 2 5 if you get 3 chirps and light flashes Your RPS Touch is now programmed Alarm rearm and lock To rearm hold your finger on the Red Circle for 2 5 seconds Alarm disarm and unlock To disarm hold your finger over the Red Circle for 2 5 seconds Once the LEDs start their circular pattern enter your 4 digit code Refer to Step 4 above Two seconds after entering the 4th digit your system will disarm Copyright 2012 Firstech LLC Page 7 F RSTECH LLC Alarm System www tirstechonline com www compustar com CM6300 Install Guide Placement and Use of Components CM6300 2 Way LCD remote paging To page a 2 Way LCD remote just tap the Red Circle twice Touch Panel Sensitivity To change touch sensitivity open the driver s door hold the button on the back of the RPS Touch until the LEDs go out Release button and tap again The number of solid LEDs represent sensitivity of touch 1 being the lowest 5 the highest RPS Touch On or Off You can turn the RPS Touch off from your remote Just follow the instructions below STEP 1 Enter remote programming mode by holding down
40. t duration to be set for a specitic length of time 1 99 sec only available when using the OP500 Aux 1 Output Control This feature allows the user to configure the method of which Auxiliary 1 can be activated Option 4 will activate AUX 1 for a set period of time based off of feature 4 01 as soon as ignition input to the CM is removed Aux 2 Output Control This feature allows the user to configure the method of which Auxiliary 2 can be activated Option 4 will activate AUX 2 for a set period of time based off of feature 4 02 as soon as the CM receives the start command Secure Aux Output This feature in the default option should help prevent accidental activation of the AUX outputs 2way remotes will require button IV or start button to be tapped before activating any of the AUX outputs Two remotes require the user to hold trunk start buttons for 2 5 seconds before activating AUX outputs Option setting II turns this feature off Aux 1 Input This feature changes the input behavior of the pre warn wire on the Aux Input Sensor green connector Default 1 Will pre warn with a negative ground input Option 2 Will instant trigger with a negative ground input Option 3 Will disarm the alarm with a negative ground input Used when adding an alarm to a factory keyless entry system Option 4 Changes the output into an open circuit input lessen Alarm System www tirstechonline com www compustar com CM6300 I
41. this feature you must perform the following procedures STEP 1 Turn on Option 3 10 II STEP 2 Turn ignition key to the on position STEP 3 Hold down the valet switch for 1 5 seconds The LED on the valet switch will begin to flash rapidly with successful completion of this step STEP 4 Enter the first digit of the desired two digit pass code by depressing the switch the number of times that coordinates with the desired first number For example to enter 3 depress the switch 3 times then wait STEP 5 The LED will confirm the first number by flashing BLUE slowly Once the LED begins to flash rapidly enter your second number by repeating step 4 STEP 6 Turn the ignition off the Secure Valet Switch is now programmed Follow steps 3 5 to enter your Secure Valet code The first two digits of the RPS unlock disarm pass code will be the default pass code for the Secure Valet you do not need to program them independently Copyright 2012 Firstech LLC Page 9 www firstechonline com www compustar com lee zeen C Alarm System CM6300 Install Guide Placement and Use of Components CM6300 DAS Sensor The DAS sensor monitors forward movement for remote starting manual transmissions dual stage impact and auto adjusting tilt sensor Follow the steps below to properly setup your DAS sensor Installing Your DAS STEP 1 Set Option 4 12 to Setting 2 STEP 2 Set switch 1 and 2 on the side of the DAS See below fo
42. trigger only when the key is in the ignition The purpose of the key sense is to prevent the system from passively arming or relocking while the key is still in the ignition Pin 13 Orange POC 6 Factory Arm 250mA negative output This is an optional output that will provide a pulse during lock after crank and again after the ignition shuts down Pin 14 Pink Closed Loop negative input This wire acts as an instant trigger when separated from ground It is most commonly used to protect headlights or trailers Pin 15 Orange White POC 7 Factory Disarm 250mA negative output This is an optional output that will provide a pulse during unlock and prior to the ignition turning on Pin 16 Yellow Black Tach Sense input Connect this wire to a tach source for Ignition controlled door locks This is option 1 09 setting 3 The doors will lock once the rpms double from what they are programmed at Pin 17 White POC 8 Horn honk 250mA negative output This is an optional output that will pulse the factory horn The proper wire will show ground while the horn is sounding To change horn output settings review Options 3 8 and 3 9 Pin 18 Gray Black Hood Pin negative input This input is a satety shut down and alarm trigger It triggers the alarm if the hood is opened while the it is armed You can connect this wire to the hood pin supplied with this kit or to a wire in the vehicle that shows only whil
43. ts will flash 1 time on the CM6 series showing V 1 and so forth Current version 3 11 should show 3 flashes when triggered What is this cartridge slot on the rear of the CM6300 A This is the slot for the Blade cartridge system This slot is for the Idatalink Blade remote start bypass modules For more information on the compatibility and install information please visit www idatalink com fitguide Using this system eliminates many connections between your standard control module and bypass module IMPORTANT If you are not using the Blade then you will not have or use the 20 pin connector next to the back up battery port I m using the RPS Touch but my LED s and Secure Valet LED does not flash A The CM6000 and CM6300 LED and Secure Valet LEDs will not work when using an RPS Touch This is a hardware limitation The RPS 2 will work with LEDs and Secure Valet Technical Support Contacts CM6300 Firstech technical support is reserved for authorized dealers only Monday Friday 888 820 3690 8 00 am 5 00 pm Pacific Coast Time Email support compustar com Web www compustar com dealersupport emm COV FL Wire Diagrams Click on the Installogy Access Client link found on your desktop If you are a qualified dealer and unable to access this site call your sales representative or the number above Copyright 2012 Firstech LLC Page 32
44. tton Tap Lock Tap Unlock Tap Trunk Tap Key Button Button Button Button Tap Lock Tap Unlock Tap Trunk Tap Key Button Button Button Button Wait for corresponding parking light flash and or siren chirp before selecting the option lessen one ee www tirstecnoniine com www compustar com CM6300 Install Guide How to Program Options on 2 Way Remotes with Separate Lock and Unlock Buttons etween each between each tap Scroll Through Select Option 1 Select Option 2 Select Option 3 ee es FE FE Menu Wait for chirp Wait for chirp a z N z Remotes Hold Trunk Button for 2 5 seconds Hold Trunk Button for 2 5 seconds Tap Lock Tap Unlock Hole in Tap Key Button for Button Button Button 2 5 seconds Hold Trunk Tap Lock Tap Unlock GE Tap Key Butt Butt Button ay ee 2 5 seconds j Lock Unlock for 2 5 seconds then Lock Unlock for 2 5 seconds Lock Unlock for 2 5 Tan K seconds then Lock Key for SPED Button 2 5 seconds Lock Key for 2 5 seconds aa Ge then Lock Unlock for 2 5 Be Button seconds Lock Key for 2 5 seconds tara then Lock Key for 2 5 GE Button seconds STEP 2 Scroll through menu allowing for 1 parking light flash and or siren chirp per step Tap Key Button Tap Lock Tap Unlock Button Button Tap Key Button Tap Lock Tap Unlock Button Button Wait for corresponding parking light flash and or siren chirp before selecting the optio
45. wire will test 12V when the trunk release is triggered Pin 3 Green Ignition 12V positive input This wire must be connected to the vehicles ignition for valet programming The proper wire will test OV with the key in the off position 12V while the key is in the on position and 12V during crank This pin also has a thin green wire that is prewired to the starter kill relay If you are not installing starter kill you do not need to use the included relay There are two wires coming off of the relay yellow black and yellow To utilize the starter kill feature the vehicle s starter wire must be cut in half otherwise cut the relay D NW out of the harness The starter kill St Sc Starter g s Ge Starter Side relay has a thin 24 gauge blue UI wire This must be connected to pin 1 24 gauge blue wire on Connector 3 Yellow Black Yellow IMPORTANT For starter kill applications the yellow wire goes to the starter side of the vehicle s starter wire and the yellow black goes to the key side Pin A Black Ground negative input This wire must be connected to the vehicle s ground The wires from the Compustar come prewired to the relay Connector 2 CN2 2 Pin Optional Battery Back up Pin 1 Red Constant 12 V positive input and charging output Pin 2 Black Ground negative input Copyright 2012 Firstech LLC Page 14 lessen Alarm System www tirstechonl

CM6300 - Compustar

Contents

Download Pdf Manuals

Related Search

Related Contents