Worldwide Lighting W83116C19-CH Installation Guide
Contents
1. Frame Parts List 02 Crossbar VAYAYAYAYAYAYAYAYAYAYAYAYAVAVAVAYAYAYVAVAVAVAYA YAYA VA TATAY EAAAAAAAAAAANSI SISI SINI NNNNA NINININI VAYAYAYAYAYAYAYAVAYAYAYAVAVAVAVAVAVAVA VAVA VAYA YAYATA TAVAYAYAYAVAVAVAVAVAYAVA VAYA YAYA VAVA VAVA VA VAVA TAT UUAZAZZAAAZZZZZAZZZZAZZAZAAAZ AAAA SISI NINININI NINININI 7 7 7 7 03 04 Chains Ol Lamp Body WARNING Crystal Dressing Diagram CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please have extreme caution when unpacking and installing When dressing the chandelier WARNING 11 with the crystals please remember mam e M eA NM to wear either rubber or cotton gloves So as to prevent any damage or smudging on the crystals After passing the main electrical wire through the 10mm pipe and connecting the pipe to the top main body connector place all remaining pieces as shown in numerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts n rr eR 9 9 765706 67676 6 9595205242909 209 CAUT ON 0 00 09 EX SS 4 a 1 Rated 110v 130v 60Hz bulb E12 40W maximum Take care to avoid2. UCTIONS Please read all instructions carefuly Before you proceed to install make sure that the power supply is turned off and off until installation is complete Please note that each part has been asigned a letter Please proceed in an alphabetical order A Existing Electrical Box B Crossbar 9 C Crossbar Screws D Metal Plate E Crossbar Bracket F Neutral Conductor G Hot Wire H Junction Caps Ground Wire 5 55 X 9245 XS OD OOO 4 22 NN ee NS 9 9 ee J Wire Cad 5 4 Attach the Crossbar the existing electrical using the two crossbar screws E which are not supplied and should already be in your box N i Als I VV QA IN WARNING CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please have extreme caution when unpacking and WARNING After passing the main electrical wire through the 10mm pipe and connecting the pipe to the top main body connector place all remaining pieces as shown in numerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts installing CAUTION 1 Rated 110v 130v 60Hz bulb E12 40W maximum Take care to avoid damage to the surface of lighting and wire Wearing glov
3. W 83116 19 D19 H18 L5 We are dedicated to providing the finest quality of crystal chandeliers for our customers Our master craftsman and designers pay their full attention to detail prompt and efficient service Enclosed are detailed instructions on how to properly install your chandelier Please read all instructions thoroughly If you have any questions please feel free to call our toll free chandelier hotline at 1 855 411 8999 Crystal Dressing Instructions CANOPY PARTS LIST When dressing the chandelier with the crystals please remember Existing Electrical Box to wear either rubber or cotton gloves So as to prevent any damage or smudging on the crystals Crossbar Screws Quantity Mo n ric 14mmX1 14mmX1 Chains Al 2 X1 2 5 X1 14mmX12 25 Wire Connector Shrinkable tube EI 14mmX1 BPR S22 2 X1 14mmX3 9 y1 14mmX7 Crossbar Screws x 2 not srpplied m o gt a D DI E 14mmX3 14mmX 1 UN Cable tie g VNv NN ANININ VAVA IN 40mmX 1 40mmX 1 F G Ground Wire Qu CANOPY INSTALLATION DIAGRAM VVVVAAAAAARAANAAAALAAAARANALAAAAALY VVAAAAAAAAALAAAAAAAAAAAAALAAAALY OAAAAAAAAAAAANAAAAAAAAAAAA Y WAVVVAVAAALAALAAAAAAAAAAALAALY LALAVVAVAAAAALRARAAAALAAAAALY NQAAAAAAAANAIAAAAAAAALAY SALVAAAAAANMAAARAAAD MA ALA LAID Lint tit fe L
4. damage to the surface of lighting and wire Wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to the white or blue wire Then connect to the neutral wire and double colored or bare copper wire to the ground wire 4 Never install lighting on damp ceiling The room should be Speet Al dry and well ventilated dui 5 Keep lighting away from acid alkali and other corrosive M eM EE N 09 00 N tT NN o T e W chemical or gas Clean with soft cloth only n 6 Installation must be carried out by qualified electrician B B only WY 4 7746 29 ENE NS 7 Disconnect the power before installing cleaning or replacing the lamp 8 Never cover the lighting when power is connected 9 Fixture must be secured when installing the ceiling tube chain pipe and other connecting parts 10 Take care to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code It must be in the appropriate local electrical codes Make sure that the electrical supply to the chandelier is turned off at the main fuse or circuit breaker before doing any installation im QU is not responsible for NN LVN ZN IV NN NVVVY F MV unprofessional wiring Frame Assembly Diagragram CANOPY INSTALLATION INSTR
5. es is recommended when installing 3 Connect black or red wire of the lighting to the white or blue wire Then connect to the neutral wire and double colored or bare copper wire to the ground wire 4 Never install lighting on damp ceiling The room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas Clean with soft cloth only 6 Installation must be carried out by qualified electrician only 7 Disconnect the power before installing cleaning or replacing the lamp 8 Never cover the lighting when power is connected 9 Fixture must be secured when installing the ceiling tube chain pipe and other connecting parts 10 Take care to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code It must be in the appropriate local electrical codes Make sure that the electrical supply to the chandelier is turned off at the main fuse or circuit breaker before doing any installation Worldwide lighting is not responsible for unprofessional wiring 05 Frame Assembly Instructions Installation Please read all instructions carefully Before you proceed to install make sure that the power supply is turned off and remains off until installation is complete please note that each part has been assigned a number please proceed in a numerical order Assembly Lamp B
6. ody 01 Install Crossbar with J Box and then Fixed the Canopy 03 Join the Lamp Body 01 and crossbar 02 with Chains 04 Make sure the positive and negative charges of wire and Lamp Body 02 match correctly screw the connect point with the junction cap Make sure the main wire is enough long and keep the rest wire in the 4 J box As the crystal pressing instruction hang the crystal parts Install lighting Source The end
Download Pdf Manuals
Related Search