VIC5211 A & E
Contents
1. DIVISION 28 23 23 VIC5211M VIC5211R SERIES FIBER OPTIC VIDEO INTERCOM SYSTEM ENGINEERING SPECIFICATIONS PART 1 GENERAL 1 01 SUMMARY A Fiber Optic Video Intercom System with Video Contact Closure and Bi directional Audio 1 02 SECTION INCLUDES A VICS5211M VIC5211R Series Video Transmitter Receiver Contact Closure Transmitter and Receiver and Audio Transceiver Standalone B VIC5211M R3 Series Video Transmitter Contact Closure Receiver and Audio Transceiver Rack Mount 1 03 REFERENCES A Underwriters Laboratory UL B Underwriters Laboratory Canada ULC C European Union Compliance CE 1 04 SYSTEM DESCRIPTION A Performance Requirements Provide a Video Transmitter Receiver and integrated Contact Closer Transmitter Receiver and audio transceiver system 1 The system shall utilize integrated WDM optics operating at 850 1300nm capable of simultaneous video contact closure and audio transmission on one multimode optical fiber VIC5211M VIC5211R 1 05 SUBMITTALS A Product Data Manufacturer s printed product data sheet for each type of Transmitter Receiver specified B Detail Drawings Electrical and optical connect drawings Product mounting template C Manufacturer s Installation and Operating Manual Printed installation and operating information for each type of Transmitter Receiver specified D Test Reports Manufacturer s Printed Test Report via a Tektronics VM700A Video Tes2. Optical Detector Type VT 1300nm PIN VR 850nm PIN 8 Receiver Sensitivity 1uw 30 dB Optical Power Budget 14 dB 10 Optical Attenuation No manual adjustments required 2 07 STATUS INDICATORS A Power On Red Off Off B Carrier Detect Video Carrier Active Yellow No Video Carrier Off 2 08 CONNECTORS A Optical ST B Power Contact Closure and Audio Terminal Block with Screw Clamps C Video BNC Gold Plated Center PIN 2 09 ELECTRICAL SPECIFICATIONS A Power VIC5211M 24 VAC CT VICS211R 18 VAC B Current Protection Automatic re settable solid state current limiters C Voltage Regulation Solid state Independent on each board D Circuit Board UL 94 flame rated and meets all PCI standards E Rack mount Card Shall be hot swappable with IFS Model Number R3 EIA 19 card cage 2 10 MECHANICAL SPECIFICATIONS A Surface Mount Dimensions VICS211M 7 1 x 4 9 x 2 0 18 00 cm x 12 45 cm x 5 08 cm MMO Ow gt Bi G2 MS SON Section Title 00000 2 VICS211R 10 8 x 5 7 x 1 0 27 18 cm x 14 48 cm x 2 54 cm B Rack Mount Dimensions VIC5211M ONLY 7 7 x 5 0 x 2 0 19 56 cm x 12 7 cm x 5 08 cm C Number of Rack Slots 2 D Finish Module shall be constructed of a metal enclosure with a powder coat finish model Number F63B 12 with all connections and indicators silk screened directly on unit Rack mount units shall be constructed of anodized aluminum E Weight lt 2 0 lb
3. a rack mount system to reduce complete system shut down during maintenance or repair The module shall have an MTBF of gt 100 000 hours and operate in an environment of 40 C to 74 C and relative humidity between 0 to 95 non condensing The module shall be UL and ULC listed and CE marked The circuit board shall be UL 94 flame rated and meet all PCI standards Section Title All PC boards shall be designated with part number PC board number and show appropriate revision number Housing shall be of all metal construction All LED indicators and both electrical and mechanical connections shall be identified with silk screened labels The module shall have a lifetime warranty to reduce system life cycle cost in an event of a module failure 2 04 VIDEO SPECIFICATIONS Input Video 1 volt pk pk 75 ohms Bandwidth 5 Hz 6 MHz Differential Gain lt 5 Differential Phase lt 5 Tilt lt 1 Signal Noise Ratio 60dB 2 05 CONTACT CLOSURE SPECIFICATIONS A Audio In Out 3 watts 8 20 ohms B Relay Rating 0 5 amps normally open N O 2 05 B AUDIO SPECIFICATIONS C Input Output 2 2 volts peak to peak D Bandwidth 5 Hz 6 MHz 2 06 OPTICAL SPECIFICATIONS A IFS Model Number VIC5211M VIC5211R Optical Fiber 62 5 125 micron Multimode Number of Fibers Required 1 Optical Wavelength 850nm 1300nm WDM Integrated WDM Optical Emitter Type VT 850nm Led VR 1300nm Led Transmitter Output Power 25uw 16 dB
4. be confirmed at this point 3 05 CLEANING A Follow all instructions for proper use of solvents and adhesives used for termination and splicing B At completion of the installation dispose of all fiber scraps properly 00000 3 Section Title MANUFACTURED UNITS REFERENCE TABLES Table A Product Number Descriptions VIC5211M SERIES DESCRIPTION MAX DISTANCE VIC5211M MM Video Audio Contact Closure 850 lt gt 2 5 Miles 4 KM Video Audio Contact Closure 1300 1 Fiber VIC5211M R3 MM Video Audio Data 850 lt gt Audio Data 2 5 Miles 4 KM 1300 1 Fiber Rack Mount Maximum distance is limited to optical loss of the fiber and any additional loss by connectors splices and patch panels VIC5211R DESCRIPTION MAX DISTANCE VIC5211R MM Video Audio Contact Closure 1300 lt gt 2 5 Miles 4 KM Video Audio Contact Closure 850 1 Fiber Table B Product Compatibility Chart TRANSCEIVER COMPATIBLE TRANSCEIVER VIC5211M VIC5211R VIC5211M R3 VIC5211R END OF SECTION Section Title 00000 4 Project name project number date Optional information e g owner A E
5. the approved detail drawings and in compliance with the IFS mounting template and installation manual B Rack Mount Module 19 Rack 1 Shall be installed in the IFS Model Number R3 card cage Ensure the card cage is Jawe Project name project number date Optional information e g owner A E C Opti 1 3 03 INS installed in a standard EIA 19 482 6 mm rack or wall standoff bracket adequate for the size and weight of the card cage The placement of the unit shall allow provision for cable installation and maintenance as indicated on the approved detail drawings and in compliance with the IFS installation manual cal Fibers Caution NEVER look into the end of an active optical fiber when using laser light output Eye damage can occur Wear eye protection when cleaving terminating and splicing fiber The number and type multimode or single mode of optical fiber shall meet the requirements of the IFS model number in article 2 06 used in the installation All optical fiber cables shall be properly installed and terminated with the mating optical connectors as submitted in article 2 08 A The optical link shall be tested with either a power meter at a minimum or OTDR to ensure the link budget overall path loss plus an added 3dB of optical safety margin does not exceed the optical power budget as submitted in article 2 06 All optical connectors on cable shall be cleaned in compliance to optical conn
6. ector manufactures specifications and covered with dust caps until connection to the fiber optic module TALLATION A General Locate fiber optic modules as indicated on the approved detail drawings and install Project n Optiona ame project number date information e g owner A E module in compliance with the IFS installation and operations manual 3 04 TESTING A Testing the Fiber Optic Video Link 1 2 Verify that the coax and optic fibers are properly connected Make sure that power is applied to all fiber optic modules camera and video monitor or other equipment used in the system The carrier detect indicator LED should be lit confirming a presence of a carrier signal Successful video link operation should be visible at this point as witnessed by a good quality video picture on the monitor B Testing the Fiber Optic Audio Link 1 Verify that the audio leads and optical fibers are properly connected 2 Make sure that power is applied to all fiber optic modules Pre amplifiers amplifiers or other equipment used in the system 3 Successful audio link operation should be confirmed at this point C Testing the Fiber Contact Closure Link 4 Verify that the contact leads and optical fibers are properly connected 5 Make sure that power is applied to all fiber optic modules controllers and receiver drivers or other equipment used in the system 6 Successful contact closure operation should
7. il sales ifs com Internet www ifs com B Substitutions Not Permitted C All fiber optic modules shall be supplied from a single manufacturer 2 02 MANUFACTURED UNITS A Model Number Descriptions Reference Table A Product Number Descriptions B Model Compatibility Chart Reference Table B Product Compatibility Chart 2 03 GENERAL SPECIFICATIONS A The Video Transmitter Receiver and integrated contact closure transmitter receiver and audio transceiver system shall be an IFS VIC5211M VIC5211R series The module shall be capable of transmitting full color video in real time in NTSC PAL or SECAM formats The module shall support the transmission of simplex or duplex audio as well as a return contact closure The module shall require no in field electrical or optical adjustments or in line attenuators to ease installation The module shall transmit the video contact closure and audio signals using frequency modulation of the optical signal The simultaneous video contact closure and audio transmission shall utilize an integrated WDM for increased stability and reliability of system performance The module shall provide power and carrier detect status indicating LED s for monitoring proper system operation The modules shall provide automatic re settable solid state current limiters and independent voltage regulators on each module to reduce the chance of a single point failure of the system The module shall be hot swappable in
8. s 1 0kg 2 11 ENVIRONMENTAL SPECIFICATIONS MTBF gt 100 000 Hours Operating Temp 40 C to 74 C Storage Temp 40 C to 85 C Relative Humidity 0 to 95 non condensing If product is installed under condensation conditions unit shall have conformal coating applied to the printed circuit board Add C to model number for conformal coated printed circuit board 2 12 REGULATORY AGENCIES APPROVALS AND LISTINGS A Underwriters Laboratory UL Listing Number I T E 6D16 B Underwriters Laboratory Canada ULC Listing Number I T E 6D16 C UL 94 flame rated PCB board 94VO D Conformity for Europe CE 2 13 ACCESSORIES A Card Cage IFS Model Number R3 EIA 19 card cage shall be available to house and power rack mount modules B Blank Panels IFS Model Number R3 BP shall be available to cover unused rack slots PART 3 EXECUTION 3 01 EXAMINATION A Inspect modules before installation B Modules shall be free of any cosmetic defects or damage C All optical connectors shall be covered with dust caps and remain on the module until installing cable connectors to module D Shipping box shall include the module power supply and operations manual 3 02 PREPARATION A Standalone Module Surface Mount 1 Shall be mounted on a properly prepared surface adequate for the size and weight of module The placement of the unit shall allow provision for cable installation and maintenance as indicated on
9. t Generator verifying product performance meets or exceeds the specified product performance referenced in Part 2 E Warranty Manufacturer s Printed Warranty 1 06 DELIVERY STORAGE AND HANDLING A Deliver materials in unopened factory packaging with Manufacturer s bar coding to the job site B Inspect product upon delivery to assure that specified products have been received C Store in original packaging in a climate controlled environment Storage Temperature not to exceed 40 C to 85 C 1 07 PROJECT SITE CONDITIONS A Temperature Requirements Products shall operate in an environment with an ambient temperature range of 40 C to 74 C without the assistance of fan forced cooling Project name project number date Optional information e g owner A E 00000 1 B Humidity Requirements Products shall operate in an environment with relative humidity of 0 to 95 non condensing If product is installed in condensation conditions unit shall have conformal coating applied to the printed circuit board 1 08 WARRANTY A Standard International Fiber Systems Comprehensive Lifetime Warranty IFS warrants the product to be free of factory defects under manufacture s Lifetime Warranty as submitted under article 1 05 E PART 2 PRODUCTS 2 01 MANUFACTURER A Acceptable Manufacturer International Fiber Systems Inc 16 Commerce Road Newtown CT 06470 USA Telephone 203 426 1180 Fax 203 426 3326 Ema
Download Pdf Manuals
Related Search