Shanghai Diebold Security Equipment Co., Ltd.
Contents
1. L To visit our website http www diebold cn 11 EBOLD ELECTRICAL PARAMETERS 1 Operational Power 4 x 1 5V AA battery 2 Non Operational Voltage By Circuit Protection 10VDC 3 Normal Operational Voltage Range 3 5V 7V 4 Sleeping Mode Current 4VH lt 0 5uA 7VH typ lt 2UA 5 Stand By Mode Current 4VH lt 100uA 7VH lt 300UA ACCESSORIES LIST L User s Manual 1 PC L Main key 2 PCS each door L Override Key 1 PC each door L Inner Door Key 2 PCS L Conformity Certificate 1 PC L Bolt down hardware 2 Sets L AA Battery 8 PCS 12 _DEBOLD MAINTENANCE GUARANTEE This product is guaranteed for one year from the date when it is purchased e This guarantee only applies to the product quality problems occurring under normal operating conditions except man made damages e g damages incurred from improper operation or carelessness damages incurred from assemble or disassemble repair and improper installation without permission from our company and damages incurred from force majeure The original invoice that is issued when this product is purchased must be presented when guaranteed maintenance service is provided Maintenance Record Calling Date Service Date Trouble amp Cause Action amp Result Repairer 13 EBOLD TO AFFIX THE INVOICE Please affix the invoice or copy f2. EBOLD OPERATIONS Prior to your use of Shanghai Diebold LCD electronic lock safe you have got please install batteries in accordance with FIRST TIME OPERATION first All indicators on LCD will go on and then go off Now you can follow the instructions below Al Insert the main key into the main lock keyhole please note the key direction See figure 3 and 4 Enter the factory code 1 5 9 Press the Prog button and the prompt will be displayed Turn the main key clockwise Turn the knob clockwise to open the door To follow steps for both upper and lower door TO OPEN CLOSE CE To Open Step 1 Insert the main key into the main lock keyhole please note the key direction See figure 3 and 4 Step 2 Enter your code The number you are entering will display on LCD If a wrong number is entered use the Clear button to clear it Step 3 Press the Prog button and the prompt will be displayed Step 4 Turn the main key clockwise then turn the knob clockwise to open the door _DEBOLD A Note If 3 consecutive invalid entries occur the keypad will discontinue functioning for 2 minutes and any key entry will not be accepted CG To Close Close the safe door Turn the knob counterclockwise Turn the main key counterclockwise to lock the door OOOO Remove the main key TO CHANGE CODE To follow the following ste
3. Shanghai Diebold Security Equipment Co Ltd Thank you for choosing Shanghai Diebold LCD electronic lock safe In order for you to use this product well please read this User s Manual carefully before using this product This is a new generation of LCD electronic lock safe series developed meticulously by Shanghai Diebold with succinct appearance and reliable structure All functioning indicators on LCD are clear to read and make it easy to operate Blue backlit display is pleasant to users High anti burglar capability for Diebold safe is secured with its patented boltwork and locking system Shanghai Diebold Security Equipment Co Ltd SDSEC is a joint venture with foreign partner the world famous multinational corporation Diebold Inc and is licensed to use the Diebold patents and the world famous trademark OIEBOLD For over one hundred years Diebold has been the world market leader in security products and financial equipment industry SDSEC regards high tech high standard and high quality as its basis and excellent service and good reputation as its root Note This User s Manual applies to models FDG A1 D 75L2S and FDG A1 D 110L2S EBOLD fe a EBOLD Ee L First Time Operation Insert the override key into the main lock keyhole Figure 4 P 4 turn it clockwise for 45 50 then return it counterclockwise to its reference position and remove it Now insert the main key into t
4. and align the bolt down holes Install and tighten the washers and the nuts from inside the safe Bolting down is complete now TO PROVIDE INFORMATION O If you provide the following information to service people OOL you will get quicker assistance Product Serial Number See label on the right side of product Product Model Purchase Invoice of Product Maintenance Guarantee 10 EBOLD CUSTOMER SUPPORT HOW TO OBTAIN ASSISTANCE If you have any question that this User s Manual cannot answer when using this product please take one of the following approaches to obtain assistance To call SDSEC Technical Advisory Service at TO 021 64809355 _ To send questions through SDSEC s fax response system to get product specifications Fax 86 21 6480 3291 Service hot line 133 8629 0300 ext 6320 6321 6322 or 6323 L Compensation Conditions for Product Liability Insurance This product is manufactured in line with the national standard GB 10409 2001 If any attack provided in this standard is made to this product and valuables stored in the safe are lost the following items need to be provided in order to get compensations maximum 30 000RMB from the insurance company for the losses herein e Original invoice to show that it s still within one year guarantee period e Evidence to show that you ve reported the case to the local police county level or above within 24 hours after the case happens
5. ect code is entered and the lock No Trouble Cause Solution No batteries installed Refer to TO REPLACE THE BATTERIES Install the conformity batteries No reaction 1 upon button ER i pressing Me polarity hipaa A Install the conformity batteries non conformity batteries according to Figure 5 Wrong key or incorrect insert direction Use the right key and insert it See Figure 3 and Figure 4 in the right direction Lock Low batteries Refer to TO Replace the old batteries with 9 vann REPLACE THE BATTERIES new conformity batteries open Incorrect user code Enter the right user code User code is forgotten Refer to HOW TO OBTAIN ASSISTANCE ET RELATED LINK O OO OU Override key is used in emergency Please keep it in a secure place and do not place it inside this safe If user is changed your code must be changed If your safe is not used for a long time it is suggested that you remove batteries or the circuit will possibly get damaged Please keep your code properly TO BOLT DOWN THE SAFE Place the safe where it will be installed Mark the locations of the bolt down holes See Figure 1 Move aside the safe and drill about 100mm deep holes by using an electric percussion drill with a 12mm drill bit in the marked locations Put and tighten the bolt down bolts into the holes Remove the nuts and washers Replace the safe where it will be installed
6. er the code Crog Prog keypad is used to validate the entered code ies Clear keypad is used for closing the code display or clearing the entered code 1 2 3 Oxy Qa 80 es BHHEEBEEHE F 4 f Figure 2 LCD screen will be used to display the entered code and the status graphs 1 The prompt xs will be highlighted to indicate that changing the user code is under process 2 The prompt amp will be highlighted to indicate that the electronic combination lock is unlocked 3 The prompt 4 will be highlighted to indicate that the batteries are low and the user should replace them with new ones 4 Digits will be displayed to indicate the user code entered The prompt will be displayed to indicate the corresponding code number entered at the spyproof function mode e will be displayed to indicate that the keyboard is under dead lock and the code cannot be entered now e error 1 error 2 and error 3 will be displayed respectively to indicate an incorrect user code is entered once twice and three times _DEBOLD KEY AND KNOB Key and Knob Description Wi Main Key On Override Key fa Knob E Figure 3 PANEL AND BATTERY COMPARTMENT Main Lock LCD screen e f Ge C0 X Cre Z AL j Battery Compartment Figure 4 Panel 1 0 N mn Figure 5 Removing the Compartment Cover
7. he main lock keyhole turn it clockwise to the end then turn the knob clockwise to open the door Take out four AA batteries from inside the safe and remove the battery compartment cover Figure 5 P 4 then install the batteries properly into the compartment and replace its cover To download our English User s Manual please visit our website wwwdiebold cn EBOLD CONTENTS ca First Time Operation LCD Electronic Lock Safe Figure 1 Button and LCD Screen Figure 2 Key and Knob Figure 3 Panel and Battery Compartment Figure 4 and 5 Operations To Open Close To Change Code To Test the New Code To Change the Number Entered To Use Spyproof Function To Change Batteries To Openin Emergency Beeper Indication Trouble Shooting Related Link and To Bolt Down the Safe Customer Support Electrical Parameters and Accessories List Maintenance Guarantee 12 13 MIEBOLD te SAFE WITH ELECTRONIC COMBINATION LOCK LCD screen Upper door Body Lower door Keypad Knob CEN Shelves Bolt down Inner door lock holes K Inner door a a er Bolt down holes Inner door lock gt Shelves e l 7 FDG A1 D 75L2S FDG A1 D 110L2S Figure 1 2 EBOLD BUTTONS AND LCD SCREEN Button Function OO 0 9 ten numeric keypad are used to ent
8. or this product in this place in order to present it to our customer support personnel and get assistance without delay j E i MEMO MIEBOLD a SDSEC PRODUCT SERIES LJ OO UU U Various security container and floppy disk media security container series Safe Series Vault Door Series Vault Wall Module Panels Remote Teller System RTS Series Integrated Bullet resistant and robbery proof system such as windows windows frame passageway lattice window shooting holes article receiving boxes ATM safes and After Hour Depositories AHD Access Control Systems with different complex and advanced levels Parking Lot Control Systems Integrated Security System be able to monitor and control all sensitive places within the designated facilities including alarm systems closed circuit television CCTV access controls remote facility monitoring systems and advanced telecommunication technologies No B 05033
9. ps to change code 1 Press the Prog button 2 Enter the existing code if it is the first time to change please enter the factory code 1 5 9 followed by pressing the Prog button 3 Enter the code you want to use 2 8 digits 4 Press the Prog button and the new code you have programmed will flash three times The new code has been programmed successfully The codes for upper door and lower door shall be changed in separately A You must keep your new code in mind because you have to enter the code first before you try to change it again EBOLD TO TEST THE NEW CODE 1 Insert the main key into the main lock keyhole Please note the key direction See figure 3 and 4 2 Enter the new code you have programmed If a wrong number is entered press the clear button to clear it 3 Press the Prog button and the prompt will be displayed 4 Turn the main key clockwise 5 Turn the knob clockwise to open the door A Please make sure the new code works before you close the door Turn the knob counterclockwise and turn the main key counterclockwise to lock the door then remove the main key TO CHANGE THE NUMBER ENTERED If a wrong number is entered simply press the Clear button to clear it followed by entering correct ones If the Clear button is pressed consecutively numbers on LCD will all be cleared TO USE SPYPROOF FUNCTION Before entering code press the Clear but
10. ton first Now all the numbers you are entering will display symbol _ After each operation this function will not be activated again Normal display will be functioned ET TO REPLACE THE BATTERIES When t j displays on LCD it indicates batteries are low and you need to replace with new batteries Method Remove battery cover per Figure 5 and replace with new batteries properly Place back battery cover A Note If your safe will not be used for a long time it is suggested that you remove batteries When batteries are placed back the code will be still stored TO OPEN IN EMERGENCY In case in emergency please use override key and main key to open your safe 1 Insert override key and turn it clockwise approx 4550 degrees then turn it counterclockwise and remove it see Figure 3 and 4 2 Insert main key and turn it clockwise 3 Turn the knob clockwise to open the door To follow steps for both upper and lower door A NOTE Override key is used only in emergency Please keep it in a secure place and do not place it inside this safe _DEBOLD BEEPER INDICATION One beep indicates e A button is pressed Three beeps indicate wrong code is entered After code is changed with three flashes of code on LCD to indicate the code is changed successfully activates Batteries are changed Six beeps indicate the circuit has problem TROUBLE SHOOTING E displays on LCD when corr
Download Pdf Manuals
Related Search